* Switched default PCI speed for 8540 ADS back to 33MHz

[u-boot] / include / configs / innokom.h

diff --git a/include/configs/innokom.h b/include/configs/innokom.h
index 709c0d7a9934e7bf68342b82fa304441f08ddac8..3cb9ebc454cf413b148a95c1b54aa9dcb0d5e34b 100644 (file)
--- a/include/configs/innokom.h
+++ b/include/configs/innokom.h
@@ -30,12 +30,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-/*
- * If we are developing, we might want to start U-Boot from ram
- * so we MUST NOT initialize critical regs like mem-timing ...
- */
-#define CONFIG_INIT_CRITICAL           /* undef for developing */
-
 /*
  * High Level Configuration Options
  * (easy to change)
@@ -82,9 +76,7 @@
  */
 
 /*
- * Size of malloc() pool; this lives below the uppermost 128 KiB which are
- * used for the RAM copy of the uboot code
- *
+ * Size of malloc() pool
  */
 #define CFG_MALLOC_LEN         (256*1024)
 #define CFG_GBL_DATA_SIZE      128             /* size in bytes reserved for initial data */
@@ -142,6 +134,7 @@
 #define CONFIG_SMC91111_BASE           0x14000000 /* chip select 5         */
 #undef  CONFIG_SMC_USE_32_BIT                     /* 16 bit bus access     */
 #undef  CONFIG_SMC_91111_EXT_PHY                  /* we use internal phy   */
+#define CONFIG_SMC_AUTONEG_TIMEOUT     10         /* timeout 10 seconds    */
 #undef  CONFIG_SHOW_ACTIVITY
 #define CONFIG_NET_RETRY_COUNT         10         /* # of retries          */
 
@@ -171,14 +164,42 @@
 
 #define CFG_FLASH_BASE          PHYS_FLASH_1
 
-
 /*
- * JFFS2 Partitions
+ * JFFS2 partitions
+ *
  */
-#define CFG_JFFS_CUSTOM_PART   1               /* see board/innokom/flash.c */
-#define CONFIG_MTD_INNOKOM_16MB 1              /* development flash         */
-#undef  CONFIG_MTD_INNOKOM_64MB                        /* production flash          */
+/* development flash */
+#define CONFIG_MTD_INNOKOM_16MB        1
+#undef CONFIG_MTD_INNOKOM_64MB
+
+/* production flash */
+/*
+#define CONFIG_MTD_INNOKOM_64MB        1
+#undef CONFIG_MTD_INNOKOM_16MB
+*/
 
+/* No command line, one static partition, whole device */
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV               "nor0"
+#define CONFIG_JFFS2_PART_SIZE         0xFFFFFFFF
+#define CONFIG_JFFS2_PART_OFFSET       0x00000000
+
+/* mtdparts command line support */
+/* Note: fake mtd_id used, no linux mtd map file */
+/*
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT         "nor0=innokom-0"
+*/
+
+/* development flash */
+/*
+#define MTDPARTS_DEFAULT       "mtdparts=innokom-0:256k(uboot),768k(kernel),8m(user),7m(data)"
+*/
+
+/* production flash */
+/*
+#define MTDPARTS_DEFAULT       "mtdparts=innokom-0:256k(uboot),768k(kernel),16256k(user1),16256k(user2),32m(data)"
+*/
 
 /*
  * GPIO settings