arm: ls1046ardb: Add SD secure boot target

[u-boot] / include / configs / ls1046a_common.h

diff --git a/include/configs/ls1046a_common.h b/include/configs/ls1046a_common.h
index 7c5e6350e2907639f8337f17f3592efa9a5079b5..957ffd36347f982ba6bade01e05b92cd46a93fc1 100644 (file)
--- a/include/configs/ls1046a_common.h
+++ b/include/configs/ls1046a_common.h
@@ -7,17 +7,30 @@
 #ifndef __LS1046A_COMMON_H
 #define __LS1046A_COMMON_H
 
+/* SPL build */
+#ifdef CONFIG_SPL_BUILD
+#define SPL_NO_QBMAN
+#define SPL_NO_FMAN
+#define SPL_NO_ENV
+#define SPL_NO_MISC
+#define SPL_NO_QSPI
+#define SPL_NO_USB
+#define SPL_NO_SATA
+#endif
+#if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT))
+#define SPL_NO_MMC
+#endif
+#if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SD_BOOT))
+#define SPL_NO_IFC
+#endif
+
 #define CONFIG_REMAKE_ELF
 #define CONFIG_FSL_LAYERSCAPE
-#define CONFIG_FSL_LSCH2
 #define CONFIG_MP
-#define CONFIG_SYS_FSL_CLK
 #define CONFIG_GICV2
 
 #include <asm/arch/config.h>
-#ifdef CONFIG_SYS_FSL_SRDS_1
-#define        CONFIG_SYS_HAS_SERDES
-#endif
+#include <asm/arch/stream_id_lsch2.h>
 
 /* Link Definitions */
 #define CONFIG_SYS_INIT_SP_ADDR                (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
@@ -25,7 +38,6 @@
 #define CONFIG_SUPPORT_RAW_INITRD
 
 #define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_BOARD_EARLY_INIT_F      1
 
 #define CONFIG_VERY_BIG_RAM
 #define CONFIG_SYS_DDR_SDRAM_BASE      0x80000000
@@ -45,9 +57,8 @@
 #define CONFIG_CONS_INDEX              1
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
-#define CONFIG_SYS_NS16550_CLK         (get_bus_freq(0)/2)
+#define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
 
-#define CONFIG_BAUDRATE                        115200
 #define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }
 
 /* SD boot SPL */
@@ -65,8 +76,6 @@
 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
 
 #define CONFIG_SPL_MMC_SUPPORT
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR                0x110
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS             0x500
 #define CONFIG_SPL_TEXT_BASE           0x10000000
 #define CONFIG_SPL_MAX_SIZE            0x1f000         /* 124 KiB */
 #define CONFIG_SPL_STACK               0x10020000
@@ -76,7 +85,19 @@
 #define CONFIG_SYS_SPL_MALLOC_START    (CONFIG_SPL_BSS_START_ADDR + \
                                        CONFIG_SPL_BSS_MAX_SIZE)
 #define CONFIG_SYS_SPL_MALLOC_SIZE     0x100000
-#define CONFIG_SYS_MONITOR_LEN         0xa0000
+
+#ifdef CONFIG_SECURE_BOOT
+#define CONFIG_U_BOOT_HDR_SIZE                         (16 << 10)
+/*
+ * HDR would be appended at end of image and copied to DDR along
+ * with U-Boot image. Here u-boot max. size is 512K. So if binary
+ * size increases then increase this size in case of secure boot as
+ * it uses raw u-boot image instead of fit image.
+ */
+#define CONFIG_SYS_MONITOR_LEN         (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
+#else
+#define CONFIG_SYS_MONITOR_LEN         0x100000
+#endif /* ifdef CONFIG_SECURE_BOOT */
 #endif
 
 /* NAND SPL */
@@ -96,7 +117,7 @@
 #define CONFIG_SPL_NAND_SUPPORT
 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
 #define CONFIG_SPL_TEXT_BASE           0x10000000
-#define CONFIG_SPL_MAX_SIZE            0x1d000         /* 116 KiB */
+#define CONFIG_SPL_MAX_SIZE            0x17000         /* 90 KiB */
 #define CONFIG_SPL_STACK               0x1001f000
 #define CONFIG_SYS_NAND_U_BOOT_DST     CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_NAND_U_BOOT_START   CONFIG_SYS_TEXT_BASE
@@ -118,25 +139,28 @@
 #define CONFIG_SYS_I2C_MXC_I2C4
 
 /* Command line configuration */
+#ifndef SPL_NO_ENV
 #define CONFIG_CMD_ENV
+#endif
 
 /* MMC */
-#define CONFIG_MMC
+#ifndef SPL_NO_MMC
 #ifdef CONFIG_MMC
 #define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
-#define CONFIG_GENERIC_MMC
-#define CONFIG_DOS_PARTITION
+#endif
 #endif
 
-#define CONFIG_FSL_CAAM                        /* Enable SEC/CAAM */
-
+#ifndef SPL_NO_QBMAN
 #define CONFIG_SYS_DPAA_QBMAN          /* Support Q/Bman */
+#endif
 
 /* FMan ucode */
+#ifndef SPL_NO_FMAN
 #define CONFIG_SYS_DPAA_FMAN
 #ifdef CONFIG_SYS_DPAA_FMAN
 #define CONFIG_SYS_FM_MURAM_SIZE       0x60000
+#endif
 
 #ifdef CONFIG_SD_BOOT
 /*
@@ -166,12 +190,11 @@
 
 /* Miscellaneous configurable options */
 #define CONFIG_SYS_LOAD_ADDR   (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
-#define CONFIG_ARCH_EARLY_INIT_R
-#define CONFIG_BOARD_LATE_INIT
 
 #define CONFIG_HWCONFIG
 #define HWCONFIG_BUFFER_SIZE           128
 
+#ifndef SPL_NO_MISC
 /* Initial environment variables */
 #define CONFIG_EXTRA_ENV_SETTINGS              \
        "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
@@ -189,13 +212,19 @@
 #define CONFIG_BOOTARGS                        "console=ttyS0,115200 root=/dev/ram0 " \
                                        "earlycon=uart8250,mmio,0x21c0500 " \
                                        MTDPARTS_DEFAULT
+#endif
+
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE              512     /* Console I/O Buffer Size */
 #define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE + \
                                        sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE /* Boot args buffer */
 #define CONFIG_SYS_LONGHELP
+
+#ifndef SPL_NO_MISC
 #define CONFIG_CMDLINE_EDITING         1
+#endif
+
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_MAXARGS             64      /* max command args */