added the config File for the MUNICes board.

[u-boot] / include / configs / lwmon5.h

diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h
index 3180617b1e0614d5af790317d7f435506d85972a..c5c2724dd2d6ab29b7aaec44d5b37d817f2edb61 100644 (file)
--- a/include/configs/lwmon5.h
+++ b/include/configs/lwmon5.h
@@ -71,15 +71,20 @@
 /*-----------------------------------------------------------------------
  * Initial RAM & stack pointer
  *----------------------------------------------------------------------*/
-/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache    */
-#define CFG_INIT_RAM_ADDR      CFG_OCM_BASE    /* OCM                  */
-#define CFG_OCM_DATA_ADDR      CFG_OCM_BASE
-
+/*
+ * On LWMON5 we use D-cache as init-ram and stack pointer. We also move
+ * the POST_WORD from OCM to a 440EPx register that preserves it's
+ * content during reset (GPT0_COM6). This way we reserve the OCM (16k)
+ * for logbuffer only.
+ */
+#define CFG_INIT_RAM_DCACHE    1               /* d-cache as init ram  */
+#define CFG_INIT_RAM_ADDR      0x70000000              /* DCache       */
 #define CFG_INIT_RAM_END       (4 << 10)
-#define CFG_GBL_DATA_SIZE      256             /* num bytes initial data */
+#define CFG_GBL_DATA_SIZE      256             /* num bytes initial data*/
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_POST_WORD_ADDR     (CFG_GBL_DATA_OFFSET - 0x4)
-#define CFG_INIT_SP_OFFSET     CFG_POST_WORD_ADDR
+#define CFG_INIT_SP_OFFSET     CFG_GBL_DATA_OFFSET
+#define CFG_POST_ALT_WORD_ADDR (CFG_PERIPHERAL_BASE + GPT0_COMP6)
+                                               /* unused GPT0 COMP reg */
 
 /*-----------------------------------------------------------------------
  * Serial Port
@@ -153,7 +158,7 @@
                                 CFG_POST_SPR      | \
                                 CFG_POST_UART)
 
-#define CFG_POST_CACHE_ADDR    0x10000000      /* free virtual address         */
+#define CFG_POST_CACHE_ADDR    0x7fff0000 /* free virtual address      */
 #define CONFIG_LOGBUFFER
 #define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
 
@@ -243,6 +248,18 @@
 #define CONFIG_HAS_ETH1                1       /* add support for "eth1addr"   */
 #define CONFIG_PHY1_ADDR       1
 
+/* Video console */
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_MB862xx
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_CONSOLE_EXTRA_INFO
+#define VIDEO_FB_16BPP_PIXEL_SWAP
+
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_SPLASH_SCREEN
+
 /* USB */
 #ifdef CONFIG_440EPX
 #define CONFIG_USB_OHCI
@@ -289,6 +306,10 @@
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 
+#ifdef CONFIG_VIDEO
+#define CONFIG_CMD_BMP
+#endif
+
 #ifdef CONFIG_440EPX
 #define CONFIG_CMD_USB
 #endif
@@ -414,7 +435,7 @@
 /*-----------------------------------------------------------------------
  * PPC440 GPIO Configuration
  */
-#define CFG_440_GPIO_TABLE { /*          Out             GPIO  Alternate1      Alternate2      Alternate3 */ \
+#define CFG_4xx_GPIO_TABLE { /*          Out             GPIO  Alternate1      Alternate2      Alternate3 */ \
 {                                                                                      \
 /* GPIO Core 0 */                                                                      \
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO0        EBC_ADDR(7)     DMA_REQ(2)      */      \