/*
- * (C) Copyright 2007
+ * (C) Copyright 2007-2011
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* See file CREDITS for list of people who contributed to this
* (easy to change)
*/
-#define CONFIG_MPC8247 1
-#define CONFIG_MPC8272_FAMILY 1
-#define CONFIG_MGCOGE 1
+#define CONFIG_MPC8247
+#define CONFIG_MGCOGE
+#define CONFIG_HOSTNAME mgcoge
+#define CONFIG_KM_82XX
-#define CONFIG_CPM2 1 /* Has a CPM2 */
+#define CONFIG_SYS_TEXT_BASE 0xFE000000
-/* Do boardspecific init */
-#define CONFIG_BOARD_EARLY_INIT_R 1
+/* include common defines/options for all Keymile boards */
+#include "km/keymile-common.h"
+#include "km/km-powerpc.h"
-/*
- * Select serial console configuration
- *
- * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- */
-#define CONFIG_CONS_ON_SMC /* Console is on SMC */
-#undef CONFIG_CONS_ON_SCC /* It's not on SCC */
-#undef CONFIG_CONS_NONE /* It's not on external UART */
-#define CONFIG_CONS_INDEX 2 /* SMC2 is used for console */
-
-/*
- * Select ethernet configuration
- *
- * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
- * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
- * SCC, 1-3 for FCC)
- *
- * If CONFIG_ETHER_NONE is defined, then either the ethernet routines
- * must be defined elsewhere (as for the console), or CONFIG_CMD_NET
- * must be unset.
- */
-#define CONFIG_ETHER_ON_SCC /* Ethernet is on SCC */
-#undef CONFIG_ETHER_ON_FCC /* Ethernet is not on FCC */
-#undef CONFIG_ETHER_NONE /* No external Ethernet */
-
-#define CONFIG_ETHER_INDEX 4
-#define CFG_SCC_TOUT_LOOP 10000000
-
-# define CFG_CMXSCR_VALUE (CMXSCR_RS4CS_CLK7 | CMXSCR_TS4CS_CLK8)
-
-#ifndef CONFIG_8260_CLKIN
-#define CONFIG_8260_CLKIN 66000000 /* in Hz */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-
-/*
- * Default environment settings
- */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "u-boot_addr=100000\0" \
- "kernel_addr=200000\0" \
- "fdt_addr=400000\0" \
- "rootpath=/opt/eldk-4.2/ppc_82xx\0" \
- "u-boot=/tftpboot/mgcoge/u-boot.bin\0" \
- "bootfile=/tftpboot/mgcoge/uImage\0" \
- "fdt_file=/tftpboot/mgcoge/mgcoge.dtb\0" \
- "load=tftp ${u-boot_addr} ${u-boot}\0" \
- "update=prot off fe000000 fe03ffff; era fe000000 fe03ffff; " \
- "cp.b ${u-boot_addr} fe000000 ${filesize};" \
- "prot on fe000000 fe03ffff\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "addcons=setenv bootargs ${bootargs} console=ttyCPM0,${baudrate}\0" \
- "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:" \
- "${netmask}:${hostname}:${netdev}:off panic=1\0" \
- "net_nfs=tftp ${kernel_addr} ${bootfile}; " \
- "tftp ${fdt_addr} ${fdt_file}; run nfsargs addip addcons;" \
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
- "net_self=tftp ${kernel_addr} ${bootfile}; " \
- "tftp ${fdt_addr} ${fdt_file}; " \
- "tftp ${ramdisk_addr} ${ramdisk_file}; " \
- "run ramargs addip; " \
- "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run net_nfs"
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#undef CONFIG_WATCHDOG /* disable platform specific watchdog */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xFE000000
-#define CFG_FLASH_SIZE 32
-#define CFG_FLASH_CFI
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFE000000
+#define CONFIG_SYS_FLASH_SIZE 32
+#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
-#define CFG_MAX_FLASH_BANKS 2 /* max num of flash banks */
-#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-
-#define CFG_FLASH_BASE_1 0x50000000
-#define CFG_FLASH_SIZE_1 64
-
-#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE, CFG_FLASH_BASE_1 }
-
-#define CFG_MONITOR_BASE TEXT_BASE
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#define CFG_RAMBOOT
-#endif
-
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256KB for Monitor */
-
-#define CONFIG_ENV_IS_IN_FLASH
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
-#endif /* CONFIG_ENV_IS_IN_FLASH */
-
-/* enable I2C and select the hardware/software driver */
-#undef CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
-#define CFG_I2C_SPEED 50000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-
-/*
- * Software (bit-bang) I2C driver configuration
- */
+#define CONFIG_SYS_MAX_FLASH_BANKS 3
+/* max num of sects on one chip */
+#define CONFIG_SYS_MAX_FLASH_SECT 512
-#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE (iop->pdir |= 0x00010000)
-#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
-#define I2C_READ ((iop->pdat & 0x00010000) != 0)
-#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
- else iop->pdat &= ~0x00010000
-#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
- else iop->pdat &= ~0x00020000
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+#define CONFIG_SYS_FLASH_BASE_1 0x50000000
+#define CONFIG_SYS_FLASH_SIZE_1 32
+#define CONFIG_SYS_FLASH_BASE_2 0x52000000
+#define CONFIG_SYS_FLASH_SIZE_2 32
-#define CONFIG_I2C_MULTI_BUS 1
-#define CONFIG_I2C_CMD_TREE 1
-#define CFG_MAX_I2C_BUS 2
-
-/* EEprom support */
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_I2C_MULTI_EEPROMS 1
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-#define CFG_IMMR 0xF0000000
-
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2000 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-/* Hard reset configuration word */
-#define CFG_HRCW_MASTER 0x0604b211
-
-/* No slaves */
-#define CFG_HRCW_SLAVE1 0
-#define CFG_HRCW_SLAVE2 0
-#define CFG_HRCW_SLAVE3 0
-#define CFG_HRCW_SLAVE4 0
-#define CFG_HRCW_SLAVE5 0
-#define CFG_HRCW_SLAVE6 0
-#define CFG_HRCW_SLAVE7 0
-
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#define CFG_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-#define CFG_HID0_INIT 0
-#define CFG_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE)
-
-#define CFG_HID2 0
-
-#define CFG_SIUMCR 0x4020c200
-#define CFG_SYPCR 0xFFFFFFC3
-#define CFG_BCR 0x10000000
-#define CFG_SCCR (SCCR_PCI_MODE | SCCR_PCI_MODCK)
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register 5-5
- *-----------------------------------------------------------------------
- * turn on Checkstop Reset Enable
- */
-#define CFG_RMR 0
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control 4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration 13-7
- *-----------------------------------------------------------------------
- */
-#define CFG_RCCR 0
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, \
+ CONFIG_SYS_FLASH_BASE_1, \
+ CONFIG_SYS_FLASH_BASE_2 }
+#define MTDIDS_DEFAULT "nor3=app"
/*
- * Init Memory Controller:
- *
- * Bank Bus Machine PortSz Device
- * ---- --- ------- ------ ------
- * 0 60x GPCM 8 bit FLASH
- * 1 60x SDRAM 32 bit SDRAM
- * 3 60x GPCM 8 bit GPIO/PIGGY
- * 5 60x GPCM 16 bit CFG-Flash
- *
- */
-/* Bank 0 - FLASH
- */
-#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\
- BRx_PS_8 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV2 |\
- ORxG_SCY_5_CLK |\
- ORxG_TRLX )
-
-
-/* Bank 1 - 60x bus SDRAM
- */
-#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
-#define CFG_GLOBAL_SDRAM_LIMIT (256 << 20) /* less than 256 MB */
-
-#define CFG_MPTPR 0x1800
-
-/*-----------------------------------------------------------------------------
- * Address for Mode Register Set (MRS) command
- *-----------------------------------------------------------------------------
+ * Bank 1 - 60x bus SDRAM
*/
-#define CFG_MRS_OFFS 0x00000110
-#define CFG_PSRT 0x0e
-
-#define CFG_BR1_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_SDRAM_P |\
- BRx_V)
-
-#define CFG_OR1_PRELIM CFG_OR1
+#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
+#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (256 << 20) /* less than 256 MB */
/* SDRAM initialization values
*/
-#define CFG_OR1 ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+#define CONFIG_SYS_OR1 ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & \
+ ORxS_SDAM_MSK) |\
ORxS_BPD_8 |\
ORxS_ROWST_PBI0_A7 |\
ORxS_NUMR_13)
-#define CFG_PSDMR (PSDMR_SDAM_A14_IS_A5 |\
+#define CONFIG_SYS_PSDMR (PSDMR_SDAM_A14_IS_A5 |\
PSDMR_BSMA_A14_A16 |\
PSDMR_SDA10_PBI0_A9 |\
PSDMR_RFRC_5_CLK |\
PSDMR_WRC_1C |\
PSDMR_CL_2)
-/* GPIO/PIGGY on CS3 initialization values
-*/
-#define CFG_PIGGY_BASE 0x30000000
-#define CFG_PIGGY_SIZE 128
-
-#define CFG_BR3_PRELIM ((CFG_PIGGY_BASE & BRx_BA_MSK) |\
- BRx_PS_8 | BRx_MS_GPCM_P | BRx_V)
-
-#define CFG_OR3_PRELIM (MEG_TO_AM(CFG_PIGGY_SIZE) |\
- ORxG_CSNT | ORxG_ACS_DIV2 |\
- ORxG_SCY_3_CLK | ORxG_TRLX )
-
-/* CFG-Flash on CS5 initialization values
-*/
-#define CFG_BR5_PRELIM ((CFG_FLASH_BASE_1 & BRx_BA_MSK) |\
- BRx_PS_16 | BRx_MS_GPCM_P | BRx_V)
-
-#define CFG_OR5_PRELIM (MEG_TO_AM(CFG_FLASH_SIZE_1) |\
- ORxG_CSNT | ORxG_ACS_DIV2 |\
- ORxG_SCY_5_CLK | ORxG_TRLX )
-
-#define CFG_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_KM_BOARD_EXTRA_ENV ""
-#define OF_CPU "PowerPC,8247@0"
-#define OF_SOC "soc@f0000000"
-#define OF_TBCLK (bd->bi_busfreq / 4)
-#define OF_STDOUT_PATH "/soc/cpm/serial@11a90"
+/* include further common stuff for all keymile 82xx boards */
+#include "km/km82xx-common.h"
#endif /* __CONFIG_H */
projects / u-boot / blobdiff