#undef CONFIG_USE_IRQ /* no support for IRQs */
#define CONFIG_MISC_INIT_R
+#define CONFIG_OF_LIBFDT 1
+/*
+ * The early kernel mapping on ARM currently only maps from the base of DRAM
+ * to the end of the kernel image. The kernel is loaded at DRAM base + 0x8000.
+ * The early kernel pagetable uses DRAM base + 0x4000 to DRAM base + 0x8000,
+ * so that leaves DRAM base to DRAM base + 0x4000 available.
+ */
+#define CONFIG_SYS_BOOTMAPSZ 0x4000
+
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS 1
#define CONFIG_INITRD_TAG 1
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
/* Sector */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
/* initial data */
/*
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
115200}
+#define CONFIG_GENERIC_MMC 1
#define CONFIG_MMC 1
-#define CONFIG_OMAP3_MMC 1
+#define CONFIG_OMAP_HSMMC 1
#define CONFIG_DOS_PARTITION 1
/* DDR - I use Micron DDR */
#define CONFIG_USB_DEVICE 1
#define CONFIG_USB_TTY 1
#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
-/* Change these to suit your needs */
-#define CONFIG_USBD_VENDORID 0x0451
-#define CONFIG_USBD_PRODUCTID 0x5678
-#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
-#define CONFIG_USBD_PRODUCT_NAME "Beagle"
/* commands to include */
#include <config_cmd_default.h>
#define CONFIG_SYS_I2C_SLAVE 1
#define CONFIG_SYS_I2C_BUS 0
#define CONFIG_SYS_I2C_BUS_SELECT 1
+#define CONFIG_I2C_MULTI_BUS 1
#define CONFIG_DRIVER_OMAP34XX_I2C 1
/*
"vram=12M\0" \
"dvimode=1024x768MR-16@60\0" \
"defaultdisplay=dvi\0" \
+ "mmcdev=0\0" \
"mmcroot=/dev/mmcblk0p2 rw\0" \
"mmcrootfstype=ext3 rootwait\0" \
"nandroot=/dev/mtdblock4 rw\0" \
"omapdss.def_disp=${defaultdisplay} " \
"root=${nandroot} " \
"rootfstype=${nandrootfstype}\0" \
- "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+ "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source ${loadaddr}\0" \
- "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+ "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"bootm ${loadaddr}\0" \
"bootm ${loadaddr}\0" \
#define CONFIG_BOOTCOMMAND \
- "if mmc init; then " \
+ "if mmc rescan ${mmcdev}; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
extern unsigned int boot_flash_type;
#endif
-/* additions for new relocation code, must be added to all boards */
-#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_SP_ADDR (LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE 0x800
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
#endif /* __CONFIG_H */