*/
#define CONFIG_OMAP 1 /* in a TI OMAP core */
#define CONFIG_OMAP34XX 1 /* which is a 34XX */
-#define CONFIG_OMAP3430 1 /* which is in a 3430 */
#define CONFIG_OMAP3_BEAGLE 1 /* working with BEAGLE */
#define CONFIG_SDRC /* The chip has SDRC controller */
#define STATUS_LED_BOOT STATUS_LED_BIT
#define STATUS_LED_GREEN STATUS_LED_BIT1
-/* DDR - I use Micron DDR */
-#define CONFIG_OMAP3_MICRON_DDR 1
-
/* Enable Multi Bus support for I2C */
#define CONFIG_I2C_MULTI_BUS 1
/* Probe all devices */
-#define CONFIG_SYS_I2C_NOPROBES {0x0, 0x0}
+#define CONFIG_SYS_I2C_NOPROBES {{0x0, 0x0}}
/* USB */
#define CONFIG_MUSB_UDC 1
/* USB EHCI */
#define CONFIG_CMD_USB
#define CONFIG_USB_EHCI
+
+#define CONFIG_USB_EHCI_OMAP
+/*#define CONFIG_EHCI_DCACHE*/ /* leave it disabled for now */
+#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147
+
+#define CONFIG_USB_ULPI
+#define CONFIG_USB_ULPI_VIEWPORT_OMAP
+
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_SMSC95XX
#define CONFIG_USB_ETHER_ASIX
-#define CONFIG_NET_MULTI
/* commands to include */
#include <config_cmd_default.h>
"loadaddr=0x80200000\0" \
"rdaddr=0x81000000\0" \
"usbtty=cdc_acm\0" \
- "usbethaddr=de:ad:be:ef\0" \
"bootfile=uImage.beagle\0" \
- "console=ttyS2,115200n8\0" \
+ "console=ttyO2,115200n8\0" \
"mpurate=auto\0" \
"buddy=none "\
"optargs=\0" \
"mmcdev=0\0" \
"mmcroot=/dev/mmcblk0p2 rw\0" \
"mmcrootfstype=ext3 rootwait\0" \
- "nandroot=/dev/mtdblock4 rw\0" \
- "nandrootfstype=jffs2\0" \
+ "nandroot=ubi0:rootfs ubi.mtd=4\0" \
+ "nandrootfstype=ubifs\0" \
"ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=0x81000000,64M\0" \
"ramrootfstype=ext2\0" \
"mmcargs=setenv bootargs console=${console} " \
* The stack sizes are set up in start.S using the settings below
*/
#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
-#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */
-#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */
-#endif
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
-/* SDRAM Bank Allocation method */
-#define SDRC_R_B_C 1
-
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
#define CONFIG_OMAP3_SPI
+#define CONFIG_SYS_CACHELINE_SIZE 64
+
+/* Defines for SPL */
+#define CONFIG_SPL
+#define CONFIG_SPL_NAND_SIMPLE
+#define CONFIG_SPL_TEXT_BASE 0x40200800
+#define CONFIG_SPL_MAX_SIZE (45 * 1024)
+#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
+
+#define CONFIG_SPL_BSS_START_ADDR 0x80000000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
+
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
+#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_POWER_SUPPORT
+#define CONFIG_SPL_OMAP3_ID_NAND
+#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
+
+/* NAND boot config */
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
+#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
+ 10, 11, 12, 13}
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+
+/*
+ * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
+ * 64 bytes before this address should be set aside for u-boot.img's
+ * header. That is 0x800FFFC0--0x80100000 should not be used for any
+ * other needs.
+ */
+#define CONFIG_SYS_TEXT_BASE 0x80100000
+#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
+
#endif /* __CONFIG_H */
projects / u-boot / blobdiff