Remove remnants of obsolete CONFIG_SYS_GBL_DATA_SIZE comments

[u-boot] / include / configs / omap3_evm.h

diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h
index c4aa220f78900024875a89abee1fc8908ded30b3..13a4fbf322d547aa7433a4fbbf359692d5d96ed3 100644 (file)
--- a/include/configs/omap3_evm.h
+++ b/include/configs/omap3_evm.h
@@ -71,8 +71,6 @@
 #define CONFIG_ENV_SIZE                        (128 << 10)     /* 128 KiB */
                                                /* Sector */
 #define CONFIG_SYS_MALLOC_LEN          (CONFIG_ENV_SIZE + (128 << 10))
-#define CONFIG_SYS_GBL_DATA_SIZE       128     /* bytes reserved for */
-                                               /* initial data */
 /*
  * Hardware drivers
  */
@@ -297,53 +295,48 @@
 #define PISMO1_NAND_SIZE               GPMC_SIZE_128M
 #define PISMO1_ONEN_SIZE               GPMC_SIZE_128M
 
-#define CONFIG_SYS_MAX_FLASH_SECT      520     /* max number of sectors */
-                                               /* on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS     2       /* max number of flash banks */
 #define CONFIG_SYS_MONITOR_LEN         (256 << 10)     /* Reserve 2 sectors */
 
-#define CONFIG_SYS_FLASH_BASE          boot_flash_base
+#if defined(CONFIG_CMD_NAND)
+#define CONFIG_SYS_FLASH_BASE          PISMO1_NAND_BASE
+#elif defined(CONFIG_CMD_ONENAND)
+#define CONFIG_SYS_FLASH_BASE          PISMO1_ONEN_BASE
+#endif
 
 /* Monitor at start of flash */
 #define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_ONENAND_BASE                ONENAND_MAP
 
+#define ONENAND_ENV_OFFSET             0x260000 /* environment starts here */
+#define SMNAND_ENV_OFFSET              0x260000 /* environment starts here */
+
 #if defined(CONFIG_CMD_NAND)
 #define CONFIG_NAND_OMAP_GPMC
 #define GPMC_NAND_ECC_LP_x16_LAYOUT    1
 #define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET              SMNAND_ENV_OFFSET
 #elif defined(CONFIG_CMD_ONENAND)
 #define CONFIG_ENV_IS_IN_ONENAND       1
+#define CONFIG_ENV_OFFSET              ONENAND_ENV_OFFSET
 #endif
-#define ONENAND_ENV_OFFSET             0x260000 /* environment starts here */
-#define SMNAND_ENV_OFFSET              0x260000 /* environment starts here */
 
-#define CONFIG_SYS_ENV_SECT_SIZE       boot_flash_sec
-#define CONFIG_ENV_OFFSET              boot_flash_off
-#define CONFIG_ENV_ADDR                        boot_flash_env_addr
+#define CONFIG_SYS_ENV_SECT_SIZE       (128 << 10)     /* 128 KiB */
+#define CONFIG_ENV_ADDR                        CONFIG_ENV_OFFSET
 
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
+/*
+ * Support for relocation
  */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT    (100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT    (100 * CONFIG_SYS_HZ)
-
-/* Flash banks JFFS2 should use */
-#define CONFIG_SYS_MAX_MTD_BANKS       (CONFIG_SYS_MAX_FLASH_BANKS + \
-                                       CONFIG_SYS_MAX_NAND_DEVICE)
-#define CONFIG_SYS_JFFS2_MEM_NAND
-/* use flash_info[2] */
-#define CONFIG_SYS_JFFS2_FIRST_BANK    CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS     1
-
-#ifndef __ASSEMBLY__
-extern unsigned int boot_flash_base;
-extern volatile unsigned int boot_flash_env_addr;
-extern unsigned int boot_flash_off;
-extern unsigned int boot_flash_sec;
-extern unsigned int boot_flash_type;
-#endif
+#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR       0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE       0x800
+#define CONFIG_SYS_INIT_SP_ADDR                (CONFIG_SYS_INIT_RAM_ADDR + \
+                                        CONFIG_SYS_INIT_RAM_SIZE - \
+                                        GENERATED_GBL_DATA_SIZE)
+
+/*
+ * Define the board revision statically
+ */
+/* #define CONFIG_STATIC_BOARD_REV     OMAP3EVM_BOARD_GEN_2 */
 
 /*----------------------------------------------------------------------------
  * SMSC9115 Ethernet from SMSC9118 family