#define CONFIG_OMAP54XX /* which is a 54XX */
#define CONFIG_OMAP5430 /* which is in a 5430 */
#define CONFIG_5430EVM /* working with EVM */
-#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_OMAP_GPIO
/* Get CPU defs */
#include <asm/arch/cpu.h>
#define CONFIG_DISPLAY_BOARDINFO
/* Clock Defines */
-#define V_OSCK 38400000 /* Clock output from T2 */
+#define V_OSCK 19200000 /* Clock output from T2 */
#define V_SCLK V_OSCK
-#undef CONFIG_USE_IRQ /* no support for IRQs */
#define CONFIG_MISC_INIT_R
#define CONFIG_OF_LIBFDT
#define CONFIG_DRIVER_OMAP34XX_I2C
#define CONFIG_I2C_MULTI_BUS
-/* TWL6030 */
-#define CONFIG_TWL6030_POWER
-#define CONFIG_CMD_BAT
+/* TWL6035 */
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_TWL6035_POWER
+#endif
/* MMC */
#define CONFIG_GENERIC_MMC
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV 1 /* SLOT2: eMMC(1) */
#define CONFIG_ENV_OFFSET 0xE0000
+#define CONFIG_CMD_SAVEENV
-/* USB */
-#define CONFIG_MUSB_UDC
-#define CONFIG_USB_OMAP3
-
-/* USB device configuration */
-#define CONFIG_USB_DEVICE
-#define CONFIG_USB_TTY
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
/* Flash */
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
- "console=ttyS2,115200n8\0" \
+ "console=ttyO2,115200n8\0" \
"usbtty=cdc_acm\0" \
"vram=16M\0" \
"mmcdev=0\0" \
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_PROMPT "OMAP5430 EVM # "
#define CONFIG_SYS_CBSIZE 256
/* Print Buffer Size */
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
#define CONFIG_SYS_HZ 1000
-/*
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 << 10) /* Regular stack */
-#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack */
-#endif
-
/*
* SDRAM Memory Map
* Even though we use two CS all the memory
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE 0x80000000
-#define CONFIG_SYS_INIT_RAM_ADDR 0x4030D800
-#define CONFIG_SYS_INIT_RAM_SIZE 0x800
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - \
+#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
/* Defines for SPL */
#define CONFIG_SPL
-#define CONFIG_SPL_TEXT_BASE 0x40304350
-#define CONFIG_SPL_MAX_SIZE 0x1E000 /* 120K */
-#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
+#define CONFIG_SPL_TEXT_BASE 0x40300350
+#define CONFIG_SPL_MAX_SIZE 0x19000 /* 100K */
+#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
#define CONFIG_SPL_FAT_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/omap-common/u-boot-spl.lds"
+#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
/*
* 64 bytes before this address should be set aside for u-boot.img's