/*define gps port conf. */
/* register later on to */
/*enable UART function! */
-#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
/*
* Command line configuration.
*/
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
#define CONFIG_CMD_PCI
#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */
#define MTDPARTS_DEFAULT "mtdparts=physmap-flash.0:256k(ubootl)," \
"1792k(kernel),13312k(jffs2),256k(uboot)ro,256k(oftree),-(space)"
-/*-----------------------------------------------------------------------------
-Autobooting
------------------------------------------------------------------------------*/
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* allow stopping of boot process */
- /* even with bootdelay=0 */
#undef CONFIG_BOOTARGS
-
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run bootcmd_net\" to load Kernel over TFTP and to "\
"mount root filesystem over NFS;" \
* 0x40000000 - 0x4fffffff - PCI Memory
* 0x50000000 - 0x50ffffff - PCI IO Space
* -----------------------------------------------------------------------*/
-#define CONFIG_PCI 1
-#define CONFIG_PCI_PNP 1
#define CONFIG_PCI_SCAN_SHOW 1
#define CONFIG_PCI_MEM_BUS 0x40000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
#define CONFIG_PCI_IO_SIZE 0x01000000
#define CONFIG_SYS_XLB_PIPELINING 1
-/*---------------------------------------------------------------------------
- I2C configuration
----------------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*---------------------------------------------------------------------------
- EEPROM CAT24WC32 configuration
----------------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010100x */
-#define CONFIG_SYS_I2C_FACT_ADDR 0x52 /* EEPROM CAT24WC32 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
-#define CONFIG_SYS_EEPROM_SIZE 2048
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15
-
-/*---------------------------------------------------------------------------
-RTC configuration
----------------------------------------------------------------------------*/
-#define RTC
-#define CONFIG_RTC_PCF8563 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51
-
/*---------------------------------------------------------------------------
Flash configuration
---------------------------------------------------------------------------*/
Environment settings
---------------------------------------------------------------------------*/
-/* pcm030 ships with environment is EEPROM by default */
-#define CONFIG_ENV_IS_IN_EEPROM 1
+#define CONFIG_ENV_IS_NOWHERE
#define CONFIG_ENV_OFFSET 0x00 /* environment starts at the */
/*beginning of the EEPROM */
-#define CONFIG_ENV_SIZE CONFIG_SYS_EEPROM_SIZE
+#define CONFIG_ENV_SIZE 2048
#define CONFIG_ENV_OVERWRITE 1
#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
-#define CONFIG_DISPLAY_BOARDINFO 1
-
/*-----------------------------------------------------------------------------
Various low-level settings
-----------------------------------------------------------------------------*/
#define CONFIG_SYS_ATA_STRIDE 4
#define CONFIG_ATAPI 1
-/* we enable IDE and FAT support, so we also need partition support */
-#define CONFIG_DOS_PARTITION 1
-
/* USB */
#define CONFIG_USB_OHCI
-#define CONFIG_USB_STORAGE
/* pass open firmware flat tree */
-#define CONFIG_OF_BOARD_SETUP 1
-
#define OF_CPU "PowerPC,5200@0"
#define OF_TBCLK CONFIG_SYS_MPC5XXX_CLKIN
#define OF_SOC "soc5200@f0000000"