arm: mach-omap2: Generate MLO file from SD boot capable targets

[u-boot] / include / configs / pdm360ng.h

diff --git a/include/configs/pdm360ng.h b/include/configs/pdm360ng.h
index 17d7bcab0087538a5f1210c390ccaf35d69b6d47..676d55f5e8b10ead9d3501bd08a66fc95bce89b2 100644 (file)
--- a/include/configs/pdm360ng.h
+++ b/include/configs/pdm360ng.h
@@ -13,8 +13,6 @@
 #define __CONFIG_H
 
 #define CONFIG_PDM360NG 1
-#define CONFIG_DISPLAY_BOARDINFO
-#define CONFIG_SYS_GENERIC_BOARD
 
 /*
  * Memory map for the PDM360NG board:
@@ -38,14 +36,10 @@
 
 /* Used for silent command in environment */
 #define CONFIG_SYS_DEVICE_NULLDEV
-#define CONFIG_SILENT_CONSOLE
 
 /* Video */
-#define CONFIG_VIDEO
 
 #if defined(CONFIG_VIDEO)
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VGA_AS_SINGLE_DEVICE
 #define CONFIG_SPLASH_SCREEN
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_VIDEO_BMP_RLE8
@@ -251,14 +245,6 @@
                                        "f8000000.flash:-(unused);"     \
                                        "MPC5121 NAND:1024m(extended-userfs)"
 
-/*
- * Override partitions in device tree using info
- * in "mtdparts" environment variable
- */
-#ifdef CONFIG_CMD_MTDPARTS
-#define CONFIG_FDT_FIXUP_PARTITIONS
-#endif
-
 #define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_TEXT_BASE    /* Start of monitor */
 #define CONFIG_SYS_MONITOR_LEN         (512 * 1024)    /* 512 kB for monitor */
 #ifdef CONFIG_FSL_DIU_FB
@@ -315,34 +301,11 @@
 #define CONFIG_SYS_PDM360NG_COPROC_READ_DELAY  5000
 #define CONFIG_SYS_PDM360NG_COPROC_BAUDRATE    38400
 
-/*
- * I2C
- */
-#define CONFIG_HARD_I2C                        /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SPEED           100000
-#define CONFIG_SYS_I2C_SLAVE           0x7F
-
 /*
  * IIM - IC Identification Module
  */
 #undef CONFIG_FSL_IIM
 
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         2       /* 16-bit EEPROM addr */
-#define CONFIG_SYS_I2C_EEPROM_ADDR             0x50    /* ST AT24C01 */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  10      /* 10ms of delay */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      4       /* 16-Byte Write Mode */
-
-/*
- * MAC addr in EEPROM
- */
-#define CONFIG_SYS_I2C_EEPROM_BUS_NUM          0
-#define CONFIG_SYS_I2C_EEPROM_MAC_OFFSET       0x10
 /*
  * Enabled only to delete "ethaddr" before testing
  * "ethaddr" setting from EEPROM
@@ -358,12 +321,6 @@
 #define CONFIG_FEC_AN_TIMEOUT  1
 #define CONFIG_HAS_ETH0
 
-/*
- * Configure on-board RTC
- */
-#define CONFIG_RTC_M41T62                      /* use M41T00 rtc via i2c */
-#define CONFIG_SYS_I2C_RTC_ADDR                0x68    /* at address 0x68      */
-
 /*
  * Environment
  */
@@ -381,23 +338,8 @@
 #define CONFIG_LOADS_ECHO      1       /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   1       /* allow baudrate change */
 
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 
-#undef CONFIG_CMD_FUSE
-
-#ifdef CONFIG_VIDEO
-#define CONFIG_CMD_BMP
-#endif
-
 /*
  * Miscellaneous configurable options
  */
@@ -456,7 +398,6 @@
 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR                400000
 
-#define CONFIG_BOOTDELAY       5       /* -1 disables auto-boot */
 
 #define CONFIG_PREBOOT "echo;" \
        "echo PDM360NG SAMPLE;" \
@@ -464,11 +405,7 @@
 
 #define CONFIG_BOOTCOMMAND     "run env_cont"
 
-#define CONFIG_OF_LIBFDT       1
-#define CONFIG_OF_BOARD_SETUP  1
 #define CONFIG_OF_SUPPORT_OLD_DEVICE_TREES     1
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE
 
 #define OF_CPU                 "PowerPC,5121@0"
 #define OF_SOC_COMPAT          "fsl,mpc5121-immr"