+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Configuration settings for the SAMA5D4EK board.
*
* Copyright (C) 2014 Atmel
* Bo Shen <voice.shen@atmel.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
-/* No NOR flash, this definition should put before common header */
-#define CONFIG_SYS_NO_FLASH
-
#include "at91-sama5_common.h"
-/* serial console */
-#define CONFIG_ATMEL_USART
-#define CONFIG_USART_BASE ATMEL_BASE_USART3
-#define CONFIG_USART_ID ATMEL_ID_USART3
-
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
-#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
+#define CONFIG_SYS_SDRAM_BASE 0x20000000
#define CONFIG_SYS_SDRAM_SIZE 0x20000000
#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_INIT_SP_ADDR 0x210000
+#define CONFIG_SYS_INIT_SP_ADDR 0x218000
#else
#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+ (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
#endif
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
-/* SerialFlash */
-#define CONFIG_CMD_SF
-
#ifdef CONFIG_CMD_SF
-#define CONFIG_ATMEL_SPI
-#define CONFIG_ATMEL_SPI0
-#define CONFIG_SPI_FLASH_ATMEL
-#define CONFIG_SF_DEFAULT_BUS 0
-#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_SF_DEFAULT_SPEED 30000000
#endif
/* NAND flash */
-#define CONFIG_CMD_NAND
-
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_ATMEL
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
+#define CONFIG_SYS_NAND_BASE 0x80000000
/* our ALE is AD21 */
#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
/* our CLE is AD22 */
#define CONFIG_ATMEL_NAND_HW_PMECC
#endif
-/* MMC */
-#define CONFIG_CMD_MMC
-
-#ifdef CONFIG_CMD_MMC
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#define ATMEL_BASE_MMCI ATMEL_BASE_MCI1
-#endif
-
-/* USB */
-#define CONFIG_CMD_USB
-
-#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_ATMEL
-#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
-#define CONFIG_USB_STORAGE
-#endif
-
-/* USB device */
-#define CONFIG_USB_GADGET
-#define CONFIG_USB_GADGET_DUALSPEED
-#define CONFIG_USB_GADGET_ATMEL_USBA
-#define CONFIG_USB_ETHER
-#define CONFIG_USB_ETH_RNDIS
-#define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D4EK"
-
-#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-
-/* Ethernet Hardware */
-#define CONFIG_MACB
-#define CONFIG_RMII
-#define CONFIG_NET_RETRY_COUNT 20
-#define CONFIG_MACB_SEARCH_PHY
-
-/* LCD */
-#define CONFIG_LCD
-#define LCD_BPP LCD_COLOR16
-#define LCD_OUTPUT_BPP 18
-#define CONFIG_LCD_LOGO
-#define CONFIG_LCD_INFO
-#define CONFIG_LCD_INFO_BELOW_LOGO
-#define CONFIG_SYS_WHITE_ON_BLACK
-#define CONFIG_ATMEL_HLCD
-#define CONFIG_ATMEL_LCD_RGB565
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-
-#ifdef CONFIG_SYS_USE_SERIALFLASH
-/* bootstrap + u-boot + env + linux in serial flash */
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
-#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
-#define CONFIG_ENV_OFFSET 0x10000
-#define CONFIG_ENV_SIZE 0x10000
-#define CONFIG_ENV_SECT_SIZE 0x1000
-#define CONFIG_BOOTCOMMAND "sf probe 0; " \
- "sf read 0x21000000 0xa0000 0x60000; " \
- "sf read 0x22000000 0x100000 0x300000; " \
- "bootz 0x22000000 - 0x21000000"
-#elif CONFIG_SYS_USE_NANDFLASH
-/* bootstrap + u-boot + env in nandflash */
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET 0xc0000
-#define CONFIG_ENV_OFFSET_REDUND 0x100000
-#define CONFIG_ENV_SIZE 0x20000
-#define CONFIG_BOOTCOMMAND "nand read 0x21000000 0x180000 0x80000;" \
- "nand read 0x22000000 0x200000 0x600000;" \
- "bootz 0x22000000 - 0x21000000"
-#elif CONFIG_SYS_USE_MMC
-/* bootstrap + u-boot + env in sd card */
-#define CONFIG_ENV_IS_IN_FAT
-#define CONFIG_FAT_WRITE
-#define FAT_ENV_INTERFACE "mmc"
-/*
- * We don't specify the part number, if device 0 has partition table, it means
- * the first partition; it no partition table, then take whole device as a
- * FAT file system.
- */
-#define FAT_ENV_DEVICE_AND_PART "0"
-#define FAT_ENV_FILE "uboot.env"
-#define CONFIG_ENV_SIZE 0x4000
-#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 sama5d4ek.dtb; " \
- "fatload mmc 0:1 0x22000000 zImage; " \
- "bootz 0x22000000 - 0x21000000"
-#endif
-
/* SPL */
-#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x200000
-#define CONFIG_SPL_MAX_SIZE 0x10000
+#define CONFIG_SPL_MAX_SIZE 0x18000
#define CONFIG_SPL_BSS_START_ADDR 0x20000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_GPIO_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
-
-#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_MONITOR_LEN (512 << 10)
-#ifdef CONFIG_SYS_USE_MMC
-#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds
-#define CONFIG_SPL_MMC_SUPPORT
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
+#ifdef CONFIG_SD_BOOT
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
-#define CONFIG_SPL_FAT_SUPPORT
-#define CONFIG_SPL_LIBDISK_SUPPORT
-#elif CONFIG_SYS_USE_NANDFLASH
-#define CONFIG_SPL_NAND_SUPPORT
+#elif CONFIG_SPI_BOOT
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x10000
+
+#elif CONFIG_NAND_BOOT
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
+#endif
#define CONFIG_PMECC_CAP 8
#define CONFIG_PMECC_SECTOR_SIZE 512
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
-#elif CONFIG_SYS_USE_SERIALFLASH
-#define CONFIG_SPL_SPI_SUPPORT
-#define CONFIG_SPL_SPI_FLASH_SUPPORT
-#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
-
-#endif
#endif
projects / u-boot / blobdiff