usb: ulpi: Add omap-ulpi-view port support

[u-boot] / include / configs / sbc8560.h

diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h
index a75e4be2126fd436f2f2e421f5ed8f8b787a7ae4..95c68bce3cbde94206602dce5ce5d0c858ca256e 100644 (file)
--- a/include/configs/sbc8560.h
+++ b/include/configs/sbc8560.h
@@ -92,20 +92,6 @@
 #error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC."
 #endif
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT     0xff700000      /* CCSRBAR Default      */
-
-#if XXX
-  #define CONFIG_SYS_CCSRBAR           0xfdf00000      /* relocated CCSRBAR    */
-#else
-  #define CONFIG_SYS_CCSRBAR           0xff700000      /* default CCSRBAR      */
-#endif
-#define CONFIG_SYS_CCSRBAR_PHYS        CONFIG_SYS_CCSRBAR      /* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR    */
-
 #define CONFIG_SYS_SDRAM_SIZE          512             /* DDR is 512MB */
 
 /* DDR Setup */
@@ -116,7 +102,7 @@
 #undef  CONFIG_DDR_SPD
 
 #if defined(CONFIG_MPC85xx_REV1)
-  #define CONFIG_DDR_DLL                       /* possible DLL fix needed      */
+#define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN    /* possible DLL fix needed */
 #endif
 
 #undef  CONFIG_DDR_ECC                     /* only for ECC DDR module */
@@ -191,10 +177,9 @@
 
 #define CONFIG_SYS_INIT_RAM_LOCK       1
 #define CONFIG_SYS_INIT_RAM_ADDR       0x70000000      /* Initial RAM address  */
-#define CONFIG_SYS_INIT_RAM_END        0x4000          /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE       0x4000          /* Size of used area in RAM */
 
-#define CONFIG_SYS_GBL_DATA_SIZE       128             /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
 #define CONFIG_SYS_MONITOR_LEN         (256 * 1024)    /* Reserve 256 kB for Mon */
@@ -245,10 +230,6 @@
 
 #ifdef CONFIG_TSEC_ENET
 
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI       1
-#endif
-
 #ifndef CONFIG_MII
 #define CONFIG_MII             1       /* MII PHY management */
 #endif
@@ -279,8 +260,8 @@
      * - Select bus for bd/buffers
      * - Full duplex
      */
-    #define CONFIG_SYS_CMXFCR_MASK     (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-    #define CONFIG_SYS_CMXFCR_VALUE    (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
+    #define CONFIG_SYS_CMXFCR_MASK2    (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+    #define CONFIG_SYS_CMXFCR_VALUE2   (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
     #define CONFIG_SYS_CPMFCR_RAMTYPE  0
     #define CONFIG_SYS_FCC_PSMR        (FCC_PSMR_FDE)
 
@@ -424,14 +405,6 @@
  */
 #define CONFIG_SYS_BOOTMAPSZ           (8 << 20) /* Initial Memory map for Linux */
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD  0x01            /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM  0x02            /* Software reboot              */
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
@@ -455,8 +428,8 @@
  */
 
 #define CONFIG_HOSTNAME                SBC8560
-#define CONFIG_ROOTPATH                /home/ppc
-#define CONFIG_BOOTFILE                uImage
+#define CONFIG_ROOTPATH                "/home/ppc"
+#define CONFIG_BOOTFILE                "uImage"
 
 #define        CONFIG_EXTRA_ENV_SETTINGS               \
        "netdev=eth0\0"                         \