#ifndef __CONFIG_H
#define __CONFIG_H
-#define GRUSS_TESTING
+#define CONFIG_SKIP_RELOCATE_UBOOT
+
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_X86 1 /* This is a X86 CPU */
-#define CONFIG_SC520 1 /* Include support for AMD SC520 */
+#define CONFIG_SYS_SC520 1 /* Include support for AMD SC520 */
#define CONFIG_ALI152X 1 /* Include support for Ali 152x SIO */
-#define CFG_SDRAM_PRECHARGE_DELAY 6 /* 6T */
-#define CFG_SDRAM_REFRESH_RATE 78 /* 7.8uS (choices are 7.8, 15.6, 31.2 or 62.5uS) */
-#define CFG_SDRAM_RAS_CAS_DELAY 3 /* 3T */
+#define CONFIG_SYS_SDRAM_PRECHARGE_DELAY 6 /* 6T */
+#define CONFIG_SYS_SDRAM_REFRESH_RATE 78 /* 7.8uS (choices are 7.8, 15.6, 31.2 or 62.5uS) */
+#define CONFIG_SYS_SDRAM_RAS_CAS_DELAY 3 /* 3T */
/* define at most one of these */
-#undef CFG_SDRAM_CAS_LATENCY_2T
-#define CFG_SDRAM_CAS_LATENCY_3T
-
-#define CFG_SC520_HIGH_SPEED 0 /* 100 or 133MHz */
-#define CFG_RESET_GENERIC 1 /* use tripple-fault to reset cpu */
-#undef CFG_RESET_SC520 /* use SC520 MMCR's to reset cpu */
-#undef CFG_TIMER_SC520 /* use SC520 swtimers */
-#define CFG_TIMER_GENERIC 1 /* use the i8254 PIT timers */
-#undef CFG_TIMER_TSC /* use the Pentium TSC timers */
-#define CFG_USE_SIO_UART 0 /* prefer the uarts on the SIO to those
+#undef CONFIG_SYS_SDRAM_CAS_LATENCY_2T
+#define CONFIG_SYS_SDRAM_CAS_LATENCY_3T
+
+#define CONFIG_SYS_SC520_HIGH_SPEED 0 /* 100 or 133MHz */
+#undef CONFIG_SYS_SC520_RESET /* use SC520 MMCR's to reset cpu */
+#undef CONFIG_SYS_SC520_TIMER /* use SC520 swtimers */
+#define CONFIG_SYS_GENERIC_TIMER 1 /* use the i8254 PIT timers */
+#undef CONFIG_SYS_TSC_TIMER /* use the Pentium TSC timers */
+#define CONFIG_SYS_USE_SIO_UART 0 /* prefer the uarts on the SIO to those
* in the SC520 on the CDP */
+#define CONFIG_SYS_PCAT_INTERRUPTS
+#define CONFIG_SYS_NUM_IRQS 16
-#define CFG_STACK_SIZE 0x8000 /* Size of bootloader stack */
+#define CONFIG_SYS_STACK_SIZE 0x8000 /* Size of bootloader stack */
#define CONFIG_SHOW_BOOT_PROGRESS 1
#define CONFIG_LAST_STAGE_INIT 1
/*
* Size of malloc() pool
*/
-#define CONFIG_MALLOC_SIZE (CONFIG_ENV_SIZE + 128*1024)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
#define CONFIG_BAUDRATE 9600
#include <config_cmd_default.h>
#define CONFIG_CMD_PCI
-#ifndef GRUSS_TESTING
#define CONFIG_CMD_SATA
-#else
-#undef CONFIG_CMD_SATA
-#endif
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_NET
#define CONFIG_CMD_EEPROM
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "boot > " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x01000000 /* 1 ... 16 MB in DRAM */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "boot > " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x01000000 /* 1 ... 16 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1024 /* incrementer freq: 1kHz */
+#define CONFIG_SYS_HZ 1024 /* incrementer freq: 1kHz */
/* valid baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*-----------------------------------------------------------------------
* Physical Memory Map
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
-#define CFG_MAX_FLASH_BANKS 3 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Write */
#define CONFIG_SPI_EEPROM /* Support for SPI EEPROMs (AT25128) */
#define CONFIG_MW_EEPROM /* Support for MicroWire EEPROMs (AT93LC46) */
#define CONFIG_SPI
#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment EEPROM 16k is SPI is used or 128 bytes if MW is used*/
#define CONFIG_ENV_OFFSET 0
-#define CONFIG_SC520_CDP_USE_SPI /* Store configuration in the SPI part */
-#undef CONFIG_SC520_CDP_USE_MW /* Store configuration in the MicroWire part */
+#define CONFIG_SYS_SC520_CDP_USE_SPI /* Store configuration in the SPI part */
+#undef CONFIG_SYS_SC520_CDP_USE_MW /* Store configuration in the MicroWire part */
#define CONFIG_SPI_X 1
/*
* JFFS2 partitions
*/
/* No command line, one static partition, whole device */
-#undef CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_MTDPARTS
#define CONFIG_JFFS2_DEV "nor0"
#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
#define CONFIG_JFFS2_PART_OFFSET 0x00000000
/* mtdparts command line support */
/*
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
#define MTDIDS_DEFAULT "nor0=SC520CDP Flash Bank #0"
#define MTDPARTS_DEFAULT "mtdparts=SC520CDP Flash Bank #0:-(jffs2)"
*/
/************************************************************
*SATA/Native Stuff
************************************************************/
-#ifndef GRUSS_TESTING
-#define CFG_SATA_MAXBUS 2 /*Max Sata buses supported */
-#define CFG_SATA_DEVS_PER_BUS 2 /*Max no. of devices per bus/port */
-#define CFG_SATA_MAX_DEVICE (CFG_SATA_MAXBUS* CFG_SATA_DEVS_PER_BUS)
+#define CONFIG_SYS_SATA_MAXBUS 2 /*Max Sata buses supported */
+#define CONFIG_SYS_SATA_DEVS_PER_BUS 2 /*Max no. of devices per bus/port */
+#define CONFIG_SYS_SATA_MAX_DEVICE (CONFIG_SYS_SATA_MAXBUS* CONFIG_SYS_SATA_DEVS_PER_BUS)
#define CONFIG_ATA_PIIX 1 /*Supports ata_piix driver */
-#else
-#undef CFG_SATA_MAXBUS
-#undef CFG_SATA_DEVS_PER_BUS
-#undef CFG_SATA_MAX_DEVICE
-#undef CONFIG_ATA_PIIX
-#endif
/************************************************************
/************************************************************
* Video/Keyboard support
************************************************************/
-#ifndef GRUSS_TESTING
#define CONFIG_VIDEO /* To enable video controller support */
-#else
-#undef CONFIG_VIDEO
-#endif
+#define PCI_VIDEO_VENDOR_ID 0 /*Use the appropriate vendor ID*/
+#define PCI_VIDEO_DEVICE_ID 0 /*Use the appropriate Device ID*/
#define CONFIG_I8042_KBD
-#define CFG_ISA_IO 0
+#define CONFIG_SYS_ISA_IO 0
/************************************************************
* RTC
/*
* PCI stuff
*/
-#ifndef GRUSS_TESTING
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_PNP /* pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW
-#define CFG_FIRST_PCI_IRQ 10
-#define CFG_SECOND_PCI_IRQ 9
-#define CFG_THIRD_PCI_IRQ 11
-#define CFG_FORTH_PCI_IRQ 15
-#else
-#undef CONFIG_PCI
-#undef CONFIG_PCI_PNP
-#undef CONFIG_PCI_SCAN_SHOW
-#endif
+#define CONFIG_SYS_FIRST_PCI_IRQ 10
+#define CONFIG_SYS_SECOND_PCI_IRQ 9
+#define CONFIG_SYS_THIRD_PCI_IRQ 11
+#define CONFIG_SYS_FORTH_PCI_IRQ 15
#endif /* __CONFIG_H */