/*
- * (C) Copyright 2006-2007
+ * (C) Copyright 2006-2008
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* (C) Copyright 2006
* Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
* Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com
*
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
-/************************************************************************
+/*
* sequoia.h - configuration for Sequoia & Rainier boards
- ***********************************************************************/
+ */
#ifndef __CONFIG_H
#define __CONFIG_H
-/*-----------------------------------------------------------------------
+/*
* High Level Configuration Options
- *----------------------------------------------------------------------*/
+ */
/* This config file is used for Sequoia (440EPx) and Rainier (440GRx) */
#ifndef CONFIG_RAINIER
-#define CONFIG_SEQUOIA 1 /* Board is Sequoia */
-#define CONFIG_440EPX 1 /* Specific PPC440EPx */
+#define CONFIG_440EPX 1 /* Specific PPC440EPx */
+#define CONFIG_HOSTNAME sequoia
#else
-#define CONFIG_440GRX 1 /* Specific PPC440GRx */
+#define CONFIG_440GRX 1 /* Specific PPC440GRx */
+#define CONFIG_HOSTNAME rainier
#endif
-#define CONFIG_4xx 1 /* ... PPC4xx family */
-#define CONFIG_SYS_CLK_FREQ 33000000 /* external freq to pll */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
-
-/*-----------------------------------------------------------------------
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- *----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-
-#define CFG_BOOT_BASE_ADDR 0xf0000000
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */
-#define CFG_OCM_BASE 0xe0010000 /* ocm */
-#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */
-#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
-#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
-#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
-#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
-
-/* Don't change either of these */
-#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
-
-#define CFG_USB2D0_BASE 0xe0000100
-#define CFG_USB_DEVICE 0xe0000000
-#define CFG_USB_HOST 0xe0000400
-#define CFG_BCSR_BASE 0xc0000000
-
-/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer
- *----------------------------------------------------------------------*/
-/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
-#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */
-#define CFG_INIT_RAM_END (4 << 10)
-#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
-/* define this if you want console on UART1 */
-#undef CONFIG_UART1_CONSOLE
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+#define CONFIG_440 1 /* ... PPC440 family */
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-#else
-#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
-#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xFFF80000
#endif
-/*-----------------------------------------------------------------------
- * FLASH related
- *----------------------------------------------------------------------*/
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
-
-#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
-
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#include "amcc-common.h"
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+/* Detect Sequoia PLL input clock automatically via CPLD bit */
+#define CONFIG_SYS_CLK_FREQ ((in8(CONFIG_SYS_BCSR_BASE + 3) & 0x80) ? \
+ 33333333 : 33000000)
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */
+/*
+ * Define this if you want support for video console with radeon 9200 pci card
+ * Also set CONFIG_SYS_TEXT_BASE to 0xFFF80000 in board/amcc/sequoia/config.mk in this case
+ */
+#undef CONFIG_VIDEO
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
+#ifdef CONFIG_VIDEO
+/*
+ * 44x dcache supported is working now on sequoia, but we don't enable
+ * it yet since it needs further testing
+ */
+#define CONFIG_4xx_DCACHE /* enable dcache */
+#endif
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
-#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
+#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
-/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
-#endif
+/*
+ * Base addresses -- Note these are effective addresses where the actual
+ * resources get mapped (not physical addresses).
+ */
+#define CONFIG_SYS_TLB_FOR_BOOT_FLASH 0x0003
+#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000
+#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */
+#define CONFIG_SYS_NAND_ADDR 0xd0000000 /* NAND Flash */
+#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */
+#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_OCM_BASE
+#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */
+#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
+#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
+
+#define CONFIG_SYS_USB2D0_BASE 0xe0000100
+#define CONFIG_SYS_USB_DEVICE 0xe0000000
+#define CONFIG_SYS_USB_HOST 0xe0000400
+#define CONFIG_SYS_BCSR_BASE 0xc0000000
/*
- * IPL (Initial Program Loader, integrated inside CPU)
- * Will load first 4k from NAND (SPL) into cache and execute it from there.
- *
- * SPL (Secondary Program Loader)
- * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
- * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
- * controller and the NAND controller so that the special U-Boot image can be
- * loaded from NAND to SDRAM.
- *
- * NUB (NAND U-Boot)
- * This NAND U-Boot (NUB) is a special U-Boot version which can be started
- * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
- *
- * On 440EPx the SPL is copied to SDRAM before the NAND controller is
- * set up. While still running from cache, I experienced problems accessing
- * the NAND controller. sr - 2006-08-25
+ * Initial RAM & stack pointer
*/
-#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
-#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
-#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */
-#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
-#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */
-#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
+/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */
+#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
/*
- * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ * Serial Port
*/
-#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
-#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
+#define CONFIG_CONS_INDEX 1 /* Use UART0 */
+#define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
/*
- * Now the NAND chip has to be defined (no autodetection used!)
+ * Environment
+ */
+#if defined(CONFIG_SYS_RAMBOOT)
+#define CONFIG_ENV_IS_NOWHERE /* Store env in memory only */
+#define CONFIG_ENV_SIZE (8 << 10)
+/*
+ * In RAM-booting version, we have no environment storage. So we need to
+ * provide at least preliminary MAC addresses for the 4xx EMAC driver to
+ * register the interfaces. Those two addresses are generated via the
+ * tools/gen_eth_addr tool and should only be used in a closed laboratory
+ * environment.
*/
-#define CFG_NAND_PAGE_SIZE (512) /* NAND chip page size */
-#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
-#define CFG_NAND_PAGE_COUNT (32) /* NAND chip page count */
-#define CFG_NAND_BAD_BLOCK_POS (5) /* Location of bad block marker */
-#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
+#define CONFIG_ETHADDR 4a:56:49:22:3e:43
+#define CONFIG_ETH1ADDR 02:93:53:d5:06:98
+#else
+#define CONFIG_ENV_IS_IN_FLASH /* use FLASH for environ vars */
+#endif
-#ifdef CFG_ENV_IS_IN_NAND
+#if defined(CONFIG_CMD_FLASH)
/*
- * For NAND booting the environment is embedded in the U-Boot image. Please take
- * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
+ * FLASH related
*/
-#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE
-#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
-#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE)
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
+
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
+
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#endif
+#endif /* CONFIG_CMD_FLASH */
-/*-----------------------------------------------------------------------
+/*
* DDR SDRAM
- *----------------------------------------------------------------------*/
-#define CFG_MBYTES_SDRAM (256) /* 256MB */
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
-#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
+ */
+#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */
+#if !defined(CONFIG_SYS_RAMBOOT)
+#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
#endif
+#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
+ /* 440EPx errata CHIP 11 */
-/*-----------------------------------------------------------------------
+/*
* I2C
- *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-
-#define CFG_I2C_MULTI_EEPROMS
-#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-/* I2C SYSMON (LM75, AD7414 is almost compatible) */
-#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_AD7414 1 /* use AD7414 */
-#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CFG_DTT_MAX_TEMP 70
-#define CFG_DTT_LOW_TEMP -30
-#define CFG_DTT_HYSTERESIS 3
+ */
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
- "echo"
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1)
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-#undef CONFIG_BOOTARGS
+/* I2C bootstrap EEPROM */
+#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x52
+#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0
+#define CONFIG_4xx_CONFIG_BLOCKSIZE 16
-/* Setup some board specific values for the default environment variables */
-#ifndef CONFIG_RAINIER
-#define CONFIG_HOSTNAME sequoia
-#define CFG_BOOTFILE "bootfile=/tftpboot/sequoia/uImage\0"
-#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0"
-#else
-#define CONFIG_HOSTNAME rainier
-#define CFG_BOOTFILE "bootfile=/tftpboot/rainier/uImage\0"
-#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0"
-#endif
+/* I2C SYSMON (LM75, AD7414 is almost compatible) */
+#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
+#define CONFIG_DTT_AD7414 1 /* use AD7414 */
+#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
+#define CONFIG_SYS_DTT_MAX_TEMP 70
+#define CONFIG_SYS_DTT_LOW_TEMP -30
+#define CONFIG_SYS_DTT_HYSTERESIS 3
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- CFG_BOOTFILE \
- CFG_ROOTPATH \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=FC000000\0" \
"ramdisk_addr=FC180000\0" \
- "load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \
- "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \
- "cp.b 200000 FFFA0000 60000\0" \
- "upd=run load;run update\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_M88E1111_PHY 1
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
-#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
+#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_HAS_ETH0
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NET_MULTI 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY1_ADDR 1
/* USB */
#ifdef CONFIG_440EPX
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_STORAGE
+#undef CONFIG_USB_EHCI /* OHCI by default */
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_PPC4XX
+#define CONFIG_SYS_PPC4XX_USB_ADDR 0xe0000300
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_EHCI_MMIO_BIG_ENDIAN
+#define CONFIG_EHCI_DESC_BIG_ENDIAN
+#else /* CONFIG_USB_EHCI */
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_SYS_OHCI_BE_CONTROLLER
+
+#undef CONFIG_SYS_USB_OHCI_BOARD_INIT
+#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
+#define CONFIG_SYS_USB_OHCI_REGS_BASE CONFIG_SYS_USB_HOST
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
+#endif
+
+#define CONFIG_USB_STORAGE
/* Comment this out to enable USB 1.1 device */
#define USB_2_0_DEVICE
-#define CMD_USB CFG_CMD_USB
-#else
-#define CMD_USB 0 /* no USB on 440GRx */
#endif /* CONFIG_440EPX */
/* Partitions */
#define CONFIG_DOS_PARTITION
#define CONFIG_ISO_PARTITION
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DHCP | \
- CFG_CMD_DTT | \
- CFG_CMD_DIAG | \
- CFG_CMD_EEPROM | \
- CFG_CMD_ELF | \
- CFG_CMD_FAT | \
- CFG_CMD_I2C | \
- CFG_CMD_IRQ | \
- CFG_CMD_MII | \
- CFG_CMD_NAND | \
- CFG_CMD_NET | \
- CFG_CMD_NFS | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SDRAM | \
- CMD_USB)
+/*
+ * Commands additional to the ones defined in amcc-common.h
+ */
+#define CONFIG_CMD_CHIP_CONFIG
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_SDRAM
-#define CONFIG_SUPPORT_VFAT
+#ifdef CONFIG_440EPX
+#define CONFIG_CMD_USB
+#endif
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#ifndef CONFIG_RAINIER
+#define CONFIG_SYS_POST_FPU_ON CONFIG_SYS_POST_FPU
+#else
+#define CONFIG_SYS_POST_FPU_ON 0
+#endif
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+/*
+ * Don't run the memory POST on the NAND-booting version. It will
+ * overwrite part of the U-Boot image which is already loaded from NAND
+ * to SDRAM.
+ */
+#if defined(CONFIG_SYS_RAMBOOT)
+#define CONFIG_SYS_POST_MEMORY_ON 0
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_POST_MEMORY_ON CONFIG_SYS_POST_MEMORY
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+/* POST support */
+#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \
+ CONFIG_SYS_POST_CPU | \
+ CONFIG_SYS_POST_ETHER | \
+ CONFIG_SYS_POST_FPU_ON | \
+ CONFIG_SYS_POST_I2C | \
+ CONFIG_SYS_POST_MEMORY_ON | \
+ CONFIG_SYS_POST_SPR | \
+ CONFIG_SYS_POST_UART)
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+#define CONFIG_LOGBUFFER
+#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#define CONFIG_SUPPORT_VFAT
-/*-----------------------------------------------------------------------
+/*
* PCI stuff
- *----------------------------------------------------------------------*/
+ */
/* General PCI */
-#define CONFIG_PCI /* include pci support */
-#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
-
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_SYS_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to */
+ /* CONFIG_SYS_PCI_MEMBASE */
/* Board-specific PCI */
-#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */
-#define CFG_PCI_TARGET_INIT
-#define CFG_PCI_MASTER_INIT
+#define CONFIG_SYS_PCI_TARGET_INIT
+#define CONFIG_SYS_PCI_MASTER_INIT
+#define CONFIG_SYS_PCI_BOARD_FIXUP_IRQ
-#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
-#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
+#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */
/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
- *----------------------------------------------------------------------*/
+ */
/*
* On Sequoia CS0 and CS3 are switched when configuring for NAND booting
*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
-#define CFG_NAND_CS 3 /* NAND chip connected to CSx */
-/* Memory Bank 0 (NOR-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x03017200
-#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000)
-
-/* Memory Bank 3 (NAND-FLASH) initialization */
-#define CFG_EBC_PB3AP 0x018003c0
-#define CFG_EBC_PB3CR (CFG_NAND_ADDR | 0x1c000)
+#if !defined(CONFIG_SYS_RAMBOOT)
+#define CONFIG_SYS_NAND_CS 3 /* NAND chip connected to CSx */
+/* Memory Bank 0 (NOR-FLASH) initialization */
+#define CONFIG_SYS_EBC_PB0AP 0x03017200
+#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE | 0xda000)
+
+/* Memory Bank 3 (NAND-FLASH) initialization */
+#define CONFIG_SYS_EBC_PB3AP 0x018003c0
+#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_NAND_ADDR | 0x1c000)
#else
-#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
-/* Memory Bank 3 (NOR-FLASH) initialization */
-#define CFG_EBC_PB3AP 0x03017200
-#define CFG_EBC_PB3CR (CFG_FLASH_BASE | 0xda000)
-
-/* Memory Bank 0 (NAND-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x018003c0
-#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1c000)
+#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */
+/* Memory Bank 3 (NOR-FLASH) initialization */
+#define CONFIG_SYS_EBC_PB3AP 0x03017200
+#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_FLASH_BASE | 0xda000)
+
+/* Memory Bank 0 (NAND-FLASH) initialization */
+#define CONFIG_SYS_EBC_PB0AP 0x018003c0
+#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1c000)
#endif
-/* Memory Bank 2 (CPLD) initialization */
-#define CFG_EBC_PB2AP 0x24814580
-#define CFG_EBC_PB2CR (CFG_BCSR_BASE | 0x38000)
+/* Memory Bank 2 (CPLD) initialization */
+#define CONFIG_SYS_EBC_PB2AP 0x24814580
+#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_BCSR_BASE | 0x38000)
-/*-----------------------------------------------------------------------
- * NAND FLASH
- *----------------------------------------------------------------------*/
-#define CFG_MAX_NAND_DEVICE 1
-#define NAND_MAX_CHIPS 1
-#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
-#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- *----------------------------------------------------------------------*/
-#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
+#define CONFIG_SYS_BCSR5_PCI66EN 0x80
/*
- * Internal Definitions
- *
- * Boot Flags
+ * NAND FLASH
*/
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS)
+#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+/*
+ * PPC440 GPIO Configuration
+ */
+/* test-only: take GPIO init from pcs440ep ???? in config file */
+#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
+{ \
+/* GPIO Core 0 */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 EBC_ADDR(6) DMA_ACK(2) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO2 EBC_ADDR(5) DMA_EOT/TC(2) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO3 EBC_ADDR(4) DMA_REQ(3) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO4 EBC_ADDR(3) DMA_ACK(3) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO5 EBC_ADDR(2) DMA_EOT/TC(3) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO6 EBC_CS_N(1) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 EBC_CS_N(2) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS_N(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS_N(4) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS_N(5) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 EBC_BUS_ERR */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO12 */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO13 */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO14 */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO15 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO16 GMCTxD(4) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO17 GMCTxD(5) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO18 GMCTxD(6) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO19 GMCTxD(7) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO20 RejectPkt0 */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO21 RejectPkt1 */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO22 */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO23 SCPD0 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO24 GMCTxD(2) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO25 GMCTxD(3) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO26 */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO27 EXT_EBC_REQ USB2D_RXERROR */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO28 USB2D_TXVALID */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO29 EBC_EXT_HDLA USB2D_PAD_SUSPNDM */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO30 EBC_EXT_ACK USB2D_XCVRSELECT*/ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO31 EBC_EXR_BUSREQ USB2D_TERMSELECT*/ \
+}, \
+{ \
+/* GPIO Core 1 */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO32 USB2D_OPMODE0 EBC_DATA(2) */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO33 USB2D_OPMODE1 EBC_DATA(3) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO34 UART0_8PIN_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO36 UART0_CTS_N EBC_DATA(0) UART3_SIN*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO37 UART0_RTS_N EBC_DATA(1) UART3_SOUT*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_8PIN_DTR_N UART1_SOUT */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_8PIN_RI_N UART1_SIN */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 UIC_IRQ(0) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 UIC_IRQ(1) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 UIC_IRQ(2) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 UIC_IRQ(3) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO44 UIC_IRQ(4) DMA_ACK(1) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO45 UIC_IRQ(6) DMA_EOT/TC(1) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO46 UIC_IRQ(7) DMA_REQ(0) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO47 UIC_IRQ(8) DMA_ACK(0) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO48 UIC_IRQ(9) DMA_EOT/TC(0) */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO55 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \
+} \
+}
+
+#ifdef CONFIG_VIDEO
+#define CONFIG_BIOSEMU /* x86 bios emulator for vga bios */
+#define CONFIG_ATI_RADEON_FB /* use radeon framebuffer driver */
+#define VIDEO_IO_OFFSET 0xe8000000
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_CMD_BMP
#endif
-#endif /* __CONFIG_H */
+
+#endif /* __CONFIG_H */