stdio: Add force parameter to stdio_deregister

[u-boot] / include / configs / stxgp3.h

diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h
index 80b46a0033a56add2395c61d468e28d5b9e9c501..5fb40ebf8ba534e791b02d79a596b4a12c7bc67b 100644 (file)
--- a/include/configs/stxgp3.h
+++ b/include/configs/stxgp3.h
@@ -7,7 +7,7 @@
  * (C) Copyright 2002,2003 Motorola,Inc.
  * Xianghua Xiao <X.Xiao@motorola.com>
  *
- * SPDX-License-Identifier:    GPL-2.0+ 
+ * SPDX-License-Identifier:    GPL-2.0+
  */
 
 /* mpc8560ads board configuration file */
@@ -22,7 +22,6 @@
 /* High Level Configuration Options */
 #define CONFIG_BOOKE           1       /* BOOKE                */
 #define CONFIG_E500            1       /* BOOKE e500 family    */
-#define CONFIG_MPC85xx         1       /* MPC8540/MPC8560      */
 #define CONFIG_CPM2            1       /* has CPM2 */
 #define CONFIG_STXGP3          1       /* Silicon Tx GPPP board specific*/
 #define CONFIG_MPC8560         1
@@ -98,7 +97,7 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
 #undef CONFIG_FSL_DDR_INTERACTIVE
@@ -162,18 +161,18 @@
 /*
  * I2C
  */
-#define CONFIG_FSL_I2C         /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C                /* I2C with hardware support*/
-#undef CONFIG_SOFT_I2C                 /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED           400000  /* I2C speed and slave address  */
-#define CONFIG_SYS_I2C_SLAVE           0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED       400000
+#define CONFIG_SYS_FSL_I2C_SLAVE       0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET      0x3000
+
 #if 0
 #define CONFIG_SYS_I2C_NOPROBES        {0x00}  /* Don't probe these addrs */
 #else
 /* I did the 'if 0' so we could keep the syntax above if ever needed. */
 #undef CONFIG_SYS_I2C_NOPROBES
 #endif
-#define CONFIG_SYS_I2C_OFFSET          0x3000
 
 /* RapdIO Map configuration, mapped 1:1.
 */
@@ -331,7 +330,6 @@
 #define CONFIG_SYS_MAXARGS     16              /* max number of command args   */
 #define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 #define CONFIG_SYS_LOAD_ADDR   0x1000000       /* default load address */
-#define CONFIG_SYS_HZ          1000            /* decrementer freq: 1 ms ticks */
 
 /*
  * For booting Linux, the board info and command line data
@@ -342,7 +340,6 @@
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
 #endif
 
 /*Note: change below for your network setting!!! */