/* High Level Configuration Options */
#define CONFIG_OMAP /* in a TI OMAP core */
-#define CONFIG_OMAP34XX /* which is a 34XX */
#define CONFIG_OMAP_COMMON
#define CONFIG_MACH_TYPE MACH_TYPE_TRICORDER
#include <asm/arch/cpu.h> /* get chip and board defs */
#include <asm/arch/omap3.h>
+#define CONFIG_SYS_GENERIC_BOARD
+
/* Display CPU and Board information */
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_SILENT_CONSOLE
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
/* Clock Defines */
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
/* Hardware drivers */
+/* GPIO support */
+#define CONFIG_OMAP_GPIO
+
+/* GPIO banks */
+#define CONFIG_OMAP3_GPIO_2 /* GPIO32..63 are in GPIO bank 2 */
+
+/* LED support */
+#define CONFIG_STATUS_LED
+#define CONFIG_BOARD_SPECIFIC_LED
+#define CONFIG_CMD_LED /* LED command */
+#define STATUS_LED_BIT (1 << 0)
+#define STATUS_LED_STATE STATUS_LED_ON
+#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
+#define STATUS_LED_BIT1 (1 << 1)
+#define STATUS_LED_STATE1 STATUS_LED_ON
+#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
+#define STATUS_LED_BIT2 (1 << 2)
+#define STATUS_LED_STATE2 STATUS_LED_ON
+#define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 2)
+
/* NS16550 Configuration */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_DOS_PARTITION
/* I2C */
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 1
-#define CONFIG_DRIVER_OMAP34XX_I2C 1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_OMAP34XX
+
+
+/* EEPROM */
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_CMD_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_BUS_NUM 1
/* TWL4030 */
#define CONFIG_TWL4030_POWER
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
-#define CONFIG_NAND_OMAP_BCH8
#define CONFIG_BCH
+#define CONFIG_SYS_NAND_MAX_OOBFREE 2
+#define CONFIG_SYS_NAND_MAX_ECCPOS 56
/* commands to include */
#include <config_cmd_default.h>
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
#define CONFIG_MTD_PARTITIONS
-/* Environment information */
-#define CONFIG_ENV_OVERWRITE /* allow to overwrite serial and ethaddr */
+/* Environment information (this is the common part) */
-#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTDELAY 0
+
+/* hang() the board on panic() */
+#define CONFIG_PANIC_HANG
+
+/* environment placement (for NAND), is different for FLASHCARD but does not
+ * harm there */
+#define CONFIG_ENV_OFFSET 0x120000 /* env start */
+#define CONFIG_ENV_OFFSET_REDUND 0x2A0000 /* redundant env start */
+#define CONFIG_ENV_SIZE (16 << 10) /* use 16KiB for env */
+#define CONFIG_ENV_RANGE (384 << 10) /* allow badblocks in env */
/* the loadaddr is the same as CONFIG_SYS_LOAD_ADDR, unfortunately the defiend
* value can not be used here! */
#define CONFIG_LOADADDR 0x82000000
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CONFIG_COMMON_ENV_SETTINGS \
"console=ttyO2,115200n8\0" \
"mmcdev=0\0" \
"vram=3M\0" \
"defaultdisplay=lcd\0" \
- "kernelopts=rw rootwait\0" \
+ "kernelopts=mtdoops.mtddev=3\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "mtdids=" MTDIDS_DEFAULT "\0" \
"commonargs=" \
"setenv bootargs console=${console} " \
"${mtdparts} " \
+ "${kernelopts} " \
+ "vt.global_cursor_default=0 " \
"vram=${vram} " \
- "omapdss.def_disp=${defaultdisplay}\0" \
+ "omapdss.def_disp=${defaultdisplay}\0"
+
+#define CONFIG_BOOTCOMMAND "run autoboot"
+
+/* specific environment settings for different use cases
+ * FLASHCARD: used to run a rdimage from sdcard to program the device
+ * 'NORMAL': used to boot kernel from sdcard, nand, ...
+ *
+ * The main aim for the FLASHCARD skin is to have an embedded environment
+ * which will not be influenced by any data already on the device.
+ */
+#ifdef CONFIG_FLASHCARD
+
+#define CONFIG_ENV_IS_NOWHERE
+
+/* the rdaddr is 16 MiB before the loadaddr */
+#define CONFIG_ENV_RDADDR "rdaddr=0x81000000\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_COMMON_ENV_SETTINGS \
+ CONFIG_ENV_RDADDR \
+ "autoboot=" \
+ "run commonargs; " \
+ "setenv bootargs ${bootargs} " \
+ "flashy_updateimg=/dev/mmcblk0p1:corscience_update.img " \
+ "rdinit=/sbin/init; " \
+ "mmc dev ${mmcdev}; mmc rescan; " \
+ "fatload mmc ${mmcdev} ${loadaddr} uImage; " \
+ "fatload mmc ${mmcdev} ${rdaddr} uRamdisk; " \
+ "bootm ${loadaddr} ${rdaddr}\0"
+
+#else /* CONFIG_FLASHCARD */
+
+#define CONFIG_ENV_OVERWRITE /* allow to overwrite serial and ethaddr */
+
+#define CONFIG_ENV_IS_IN_NAND
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_COMMON_ENV_SETTINGS \
"mmcargs=" \
"run commonargs; " \
"setenv bootargs ${bootargs} " \
"root=/dev/mmcblk0p2 " \
- "${kernelopts}\0" \
+ "rootwait " \
+ "rw\0" \
"nandargs=" \
"run commonargs; " \
"setenv bootargs ${bootargs} " \
- "omapdss.def_disp=${defaultdisplay} " \
"root=ubi0:root " \
"ubi.mtd=7 " \
"rootfstype=ubifs " \
- "${kernelopts}\0" \
+ "ro\0" \
"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source ${loadaddr}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"bootm ${loadaddr}\0" \
- "loaduimage_ubi=mtd default; " \
- "ubi part ubi; " \
+ "loaduimage_ubi=ubi part ubi; " \
"ubifsmount ubi:root; " \
"ubifsload ${loadaddr} /boot/uImage\0" \
+ "loaduimage_nand=nand read ${loadaddr} kernel 0x500000\0" \
"nandboot=echo Booting from nand ...; " \
"run nandargs; " \
- "run loaduimage_ubi; " \
+ "run loaduimage_nand; " \
"bootm ${loadaddr}\0" \
- "autoboot=mtdparts default;" \
- "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "autoboot=mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
"fi; " \
"else run nandboot; fi\0"
-#define CONFIG_BOOTCOMMAND "run autoboot"
+#endif /* CONFIG_FLASHCARD */
/* Miscellaneous configurable options */
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_CMDLINE_EDITING /* enable cmdline history */
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_PROMPT "OMAP3 Tricorder # "
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
-#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0 + 0x07000000)
+#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0 + 0x00000000)
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \
- 0x01000000) /* 16MB */
+ 0x07000000) /* 112 MB */
#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0 + 0x02000000)
*/
#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-#define CONFIG_SYS_HZ 1000
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/* NAND and environment organization */
-#define PISMO1_NAND_SIZE GPMC_SIZE_128M
-
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET 0x120000 /* env start */
-#define CONFIG_ENV_OFFSET_REDUND 0x2A0000 /* redundant env start */
-#define CONFIG_ENV_SIZE (16 << 10) /* use 16KiB for env */
-#define CONFIG_ENV_RANGE (384 << 10) /* allow badblocks in env */
-
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
#define CONFIG_SYS_INIT_RAM_SIZE 0x800
#define CONFIG_SYS_SRAM_SIZE 0x10000
/* Defines for SPL */
-#define CONFIG_SPL
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_NAND_SIMPLE
#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_FAT_SUPPORT
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
-#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
-#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
+#define CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION 1
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
#define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/
-#define CONFIG_SPL_MAX_SIZE (55 * 1024) /* 7 KB for stack */
+#define CONFIG_SPL_MAX_SIZE (57 * 1024) /* 7 KB for stack */
#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
#define CONFIG_SPL_BSS_START_ADDR 0x80000000 /*CONFIG_SYS_SDRAM_BASE*/
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
-#define CONFIG_SYS_NAND_ECCPOS {12, 13, 14, 15, 16, 17, 18, 19, 20,\
- 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33,\
- 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46,\
- 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59,\
- 60, 61, 62, 63}
+#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, \
+ 13, 14, 16, 17, 18, 19, 20, 21, 22, \
+ 23, 24, 25, 26, 27, 28, 30, 31, 32, \
+ 33, 34, 35, 36, 37, 38, 39, 40, 41, \
+ 42, 44, 45, 46, 47, 48, 49, 50, 51, \
+ 52, 53, 54, 55, 56}
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 13
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_SYS_MEMTEST_SCRATCH 0x81000000
#endif /* __CONFIG_H */