mpc8xx: remove ELPT860 board support

[u-boot] / include / configs / zynq-common.h

diff --git a/include/configs/zynq-common.h b/include/configs/zynq-common.h
index 875cb43f15b8d284272aece7ce16251cba61e777..87b4fffeb9fb262143edaae2599220c04255a959 100644 (file)
--- a/include/configs/zynq-common.h
+++ b/include/configs/zynq-common.h
@@ -10,9 +10,6 @@
 #ifndef __CONFIG_ZYNQ_COMMON_H
 #define __CONFIG_ZYNQ_COMMON_H
 
-/* High Level configuration Options */
-#define CONFIG_ARMV7
-
 /* CPU clock */
 #ifndef CONFIG_CPU_FREQ_HZ
 # define CONFIG_CPU_FREQ_HZ    800000000
@@ -227,8 +224,6 @@
 #define CONFIG_IMAGE_FORMAT_LEGACY /* enable also legacy image format */
 
 /* FDT support */
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
 #define CONFIG_DISPLAY_BOARDINFO_LATE
 
 /* RSA support */
@@ -270,28 +265,23 @@
 #define CONFIG_SPL_MMC_SUPPORT
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS      0x200 /* 256 KB */
-#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION    1
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
 #define CONFIG_SPL_LIBDISK_SUPPORT
 #define CONFIG_SPL_FAT_SUPPORT
-#if defined(CONFIG_OF_CONTROL) && defined(CONFIG_OF_SEPARATE)
-# define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME     "u-boot-dtb.img"
-#else
-# define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME     "u-boot.img"
-#endif
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME     "u-boot-dtb.img"
 #endif
 
 /* Disable dcache for SPL just for sure */
 #ifdef CONFIG_SPL_BUILD
 #define CONFIG_SYS_DCACHE_OFF
 #undef CONFIG_FPGA
-#undef CONFIG_OF_CONTROL
 #endif
 
 /* Address in RAM where the parameters must be copied by SPL. */
 #define CONFIG_SYS_SPL_ARGS_ADDR       0x10000000
 
-#define CONFIG_SPL_FAT_LOAD_ARGS_NAME          "system.dtb"
-#define CONFIG_SPL_FAT_LOAD_KERNEL_NAME                "uImage"
+#define CONFIG_SPL_FS_LOAD_ARGS_NAME           "system.dtb"
+#define CONFIG_SPL_FS_LOAD_KERNEL_NAME         "uImage"
 
 /* Not using MMC raw mode - just for compilation purpose */
 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR  0
@@ -303,9 +293,7 @@
 #define CONFIG_SPL_SPI_SUPPORT
 #define CONFIG_SPL_SPI_LOAD
 #define CONFIG_SPL_SPI_FLASH_SUPPORT
-#define CONFIG_SPL_SPI_BUS     0
 #define CONFIG_SYS_SPI_U_BOOT_OFFS     0x100000
-#define CONFIG_SPL_SPI_CS      0
 #endif
 
 /* for booting directly linux */