mpc8xx: remove ELPT860 board support

[u-boot] / include / configs / zynq-common.h

diff --git a/include/configs/zynq-common.h b/include/configs/zynq-common.h
index d2149b3c2b88d64fe8621105c9435ac9f1b595c3..87b4fffeb9fb262143edaae2599220c04255a959 100644 (file)
--- a/include/configs/zynq-common.h
+++ b/include/configs/zynq-common.h
@@ -10,10 +10,6 @@
 #ifndef __CONFIG_ZYNQ_COMMON_H
 #define __CONFIG_ZYNQ_COMMON_H
 
-/* High Level configuration Options */
-#define CONFIG_ARMV7
-#define CONFIG_ZYNQ
-
 /* CPU clock */
 #ifndef CONFIG_CPU_FREQ_HZ
 # define CONFIG_CPU_FREQ_HZ    800000000
@@ -214,6 +210,10 @@
 #define CONFIG_FPGA_XILINX
 #define CONFIG_FPGA_ZYNQPL
 #define CONFIG_CMD_FPGA
+#define CONFIG_CMD_FPGA_LOADMK
+#define CONFIG_CMD_FPGA_LOADP
+#define CONFIG_CMD_FPGA_LOADBP
+#define CONFIG_CMD_FPGA_LOADFS
 
 /* Open Firmware flat tree */
 #define CONFIG_OF_LIBFDT
@@ -221,10 +221,9 @@
 /* FIT support */
 #define CONFIG_FIT
 #define CONFIG_FIT_VERBOSE     1 /* enable fit_format_{error,warning}() */
+#define CONFIG_IMAGE_FORMAT_LEGACY /* enable also legacy image format */
 
 /* FDT support */
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
 #define CONFIG_DISPLAY_BOARDINFO_LATE
 
 /* RSA support */
@@ -252,7 +251,6 @@
 #define CONFIG_CMD_TFTPPUT
 
 /* SPL part */
-#define CONFIG_SPL
 #define CONFIG_CMD_SPL
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
@@ -262,29 +260,28 @@
 
 #define CONFIG_SPL_LDSCRIPT    "arch/arm/cpu/armv7/zynq/u-boot-spl.lds"
 
-/* Disable dcache for SPL just for sure */
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_DCACHE_OFF
-#undef CONFIG_FPGA
-#undef CONFIG_OF_CONTROL
-#endif
-
 /* MMC support */
 #ifdef CONFIG_ZYNQ_SDHCI0
 #define CONFIG_SPL_MMC_SUPPORT
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS      0x200 /* 256 KB */
-#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION    1
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
 #define CONFIG_SPL_LIBDISK_SUPPORT
 #define CONFIG_SPL_FAT_SUPPORT
-#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME     "u-boot.img"
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME     "u-boot-dtb.img"
+#endif
+
+/* Disable dcache for SPL just for sure */
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_DCACHE_OFF
+#undef CONFIG_FPGA
 #endif
 
 /* Address in RAM where the parameters must be copied by SPL. */
 #define CONFIG_SYS_SPL_ARGS_ADDR       0x10000000
 
-#define CONFIG_SPL_FAT_LOAD_ARGS_NAME          "system.dtb"
-#define CONFIG_SPL_FAT_LOAD_KERNEL_NAME                "uImage"
+#define CONFIG_SPL_FS_LOAD_ARGS_NAME           "system.dtb"
+#define CONFIG_SPL_FS_LOAD_KERNEL_NAME         "uImage"
 
 /* Not using MMC raw mode - just for compilation purpose */
 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR  0
@@ -296,9 +293,7 @@
 #define CONFIG_SPL_SPI_SUPPORT
 #define CONFIG_SPL_SPI_LOAD
 #define CONFIG_SPL_SPI_FLASH_SUPPORT
-#define CONFIG_SPL_SPI_BUS     0
 #define CONFIG_SYS_SPI_U_BOOT_OFFS     0x100000
-#define CONFIG_SPL_SPI_CS      0
 #endif
 
 /* for booting directly linux */
@@ -330,4 +325,6 @@
 
 #define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
 
+#define CONFIG_SYS_GENERIC_BOARD
+
 #endif /* __CONFIG_ZYNQ_COMMON_H */