#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-/* Zynq Serial driver */
-#ifdef CONFIG_ZYNQ_SERIAL_UART0
-# define CONFIG_ZYNQ_SERIAL_BASEADDR0 0xE0000000
-# define CONFIG_ZYNQ_SERIAL_BAUDRATE0 CONFIG_BAUDRATE
-# define CONFIG_ZYNQ_SERIAL_CLOCK0 50000000
-#endif
-
-#ifdef CONFIG_ZYNQ_SERIAL_UART1
-# define CONFIG_ZYNQ_SERIAL_BASEADDR1 0xE0001000
-# define CONFIG_ZYNQ_SERIAL_BAUDRATE1 CONFIG_BAUDRATE
-# define CONFIG_ZYNQ_SERIAL_CLOCK1 50000000
-#endif
-
-#if defined(CONFIG_ZYNQ_SERIAL_UART0) || defined(CONFIG_ZYNQ_SERIAL_UART1)
-# define CONFIG_ZYNQ_SERIAL
-#endif
-
/* DCC driver */
#if defined(CONFIG_ZYNQ_DCC)
# define CONFIG_ARM_DCC
# define CONFIG_CPU_V6 /* Required by CONFIG_ARM_DCC */
+#else
+# define CONFIG_ZYNQ_SERIAL
#endif
/* Ethernet driver */
# define CONFIG_CMD_SF
#endif
+/* NOR */
+#ifndef CONFIG_SYS_NO_FLASH
+# define CONFIG_SYS_FLASH_BASE 0xE2000000
+# define CONFIG_SYS_FLASH_SIZE (16 * 1024 * 1024)
+# define CONFIG_SYS_MAX_FLASH_BANKS 1
+# define CONFIG_SYS_MAX_FLASH_SECT 512
+# define CONFIG_SYS_FLASH_ERASE_TOUT 1000
+# define CONFIG_SYS_FLASH_WRITE_TOUT 5000
+# define CONFIG_FLASH_SHOW_PROGRESS 10
+# define CONFIG_SYS_FLASH_CFI
+# undef CONFIG_SYS_FLASH_EMPTY_INFO
+# define CONFIG_FLASH_CFI_DRIVER
+# undef CONFIG_SYS_FLASH_PROTECTION
+# define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
/* MMC */
#if defined(CONFIG_ZYNQ_SDHCI0) || defined(CONFIG_ZYNQ_SDHCI1)
# define CONFIG_MMC
# define CONFIG_DOS_PARTITION
#endif
+#define CONFIG_SYS_I2C_ZYNQ
/* I2C */
-#if defined(CONFIG_ZYNQ_I2C0) || defined(CONFIG_ZYNQ_I2C1)
+#if defined(CONFIG_SYS_I2C_ZYNQ)
# define CONFIG_CMD_I2C
# define CONFIG_SYS_I2C
-# define CONFIG_SYS_I2C_ZYNQ
# define CONFIG_SYS_I2C_ZYNQ_SPEED 100000
-# define CONFIG_SYS_I2C_ZYNQ_SLAVE 1
+# define CONFIG_SYS_I2C_ZYNQ_SLAVE 0
+#endif
+
+/* EEPROM */
+#ifdef CONFIG_ZYNQ_EEPROM
+# define CONFIG_CMD_EEPROM
+# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+# define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
+# define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
+# define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+# define CONFIG_SYS_EEPROM_SIZE 1024 /* Bytes */
#endif
#define CONFIG_BOOTP_SERVERIP
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_MAY_FAIL
+/* Total Size of Environment Sector */
+#define CONFIG_ENV_SIZE (128 << 10)
+
+/* Allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
/* Environment */
-#define CONFIG_ENV_SIZE 0x10000 /* Env. sector size */
-#define CONFIG_ENV_IS_NOWHERE
-#define CONFIG_SYS_LOAD_ADDR 0
+#ifndef CONFIG_ENV_IS_NOWHERE
+# ifndef CONFIG_SYS_NO_FLASH
+# define CONFIG_ENV_IS_IN_FLASH
+# elif defined(CONFIG_SYS_NO_FLASH)
+# define CONFIG_ENV_IS_NOWHERE
+# endif
+
+# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
+# define CONFIG_ENV_OFFSET 0xE0000
+# define CONFIG_CMD_SAVEENV
+#endif
+
+/* Default environment */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "fit_image=fit.itb\0" \
+ "load_addr=0x2000000\0" \
+ "fit_size=0x800000\0" \
+ "flash_off=0x100000\0" \
+ "nor_flash_off=0xE2100000\0" \
+ "fdt_high=0x20000000\0" \
+ "initrd_high=0x20000000\0" \
+ "norboot=echo Copying FIT from NOR flash to RAM... && " \
+ "cp.b ${nor_flash_off} ${load_addr} ${fit_size} && " \
+ "bootm ${load_addr}\0" \
+ "sdboot=echo Copying FIT from SD to RAM... && " \
+ "fatload mmc 0 ${load_addr} ${fit_image} && " \
+ "bootm ${load_addr}\0" \
+ "jtagboot=echo TFTPing FIT to RAM... && " \
+ "tftpboot ${load_addr} ${fit_image} && " \
+ "bootm ${load_addr}\0"
+#define CONFIG_BOOTCOMMAND "run $modeboot"
+#define CONFIG_BOOTDELAY 3 /* -1 to Disable autoboot */
+#define CONFIG_SYS_LOAD_ADDR 0 /* default? */
/* Miscellaneous configurable options */
#define CONFIG_SYS_PROMPT "zynq-uboot> "
#define CONFIG_CMDLINE_EDITING
#define CONFIG_AUTO_COMPLETE
+#define CONFIG_BOARD_LATE_INIT
#define CONFIG_SYS_LONGHELP
+#define CONFIG_CLOCKS
+#define CONFIG_CMD_CLK
#define CONFIG_SYS_MAXARGS 15 /* max number of command args */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
#define CONFIG_FPGA_XILINX
#define CONFIG_FPGA_ZYNQPL
#define CONFIG_CMD_FPGA
+#define CONFIG_CMD_FPGA_LOADMK
+#define CONFIG_CMD_FPGA_LOADP
+#define CONFIG_CMD_FPGA_LOADBP
+#define CONFIG_CMD_FPGA_LOADFS
/* Open Firmware flat tree */
#define CONFIG_OF_LIBFDT
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
+/* FDT support */
+#define CONFIG_OF_CONTROL
+#define CONFIG_OF_SEPARATE
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+
+/* RSA support */
+#define CONFIG_FIT_SIGNATURE
+#define CONFIG_RSA
+
+/* Extend size of kernel image for uncompression */
+#define CONFIG_SYS_BOOTM_LEN (20 * 1024 * 1024)
+
/* Boot FreeBSD/vxWorks from an ELF image */
#if defined(CONFIG_ZYNQ_BOOT_FREEBSD)
# define CONFIG_API
# define CONFIG_SYS_MMC_MAX_DEVICE 1
#endif
+#define CONFIG_SYS_LDSCRIPT "arch/arm/cpu/armv7/zynq/u-boot.lds"
+
/* Commands */
#include <config_cmd_default.h>
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII
+#define CONFIG_CMD_TFTPPUT
+
+/* SPL part */
+#define CONFIG_SPL
+#define CONFIG_CMD_SPL
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+
+#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/zynq/u-boot-spl.lds"
+
+/* Disable dcache for SPL just for sure */
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_DCACHE_OFF
+#undef CONFIG_FPGA
+#undef CONFIG_OF_CONTROL
+#endif
+
+/* MMC support */
+#ifdef CONFIG_ZYNQ_SDHCI0
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
+#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+#endif
+
+/* Address in RAM where the parameters must be copied by SPL. */
+#define CONFIG_SYS_SPL_ARGS_ADDR 0x10000000
+
+#define CONFIG_SPL_FAT_LOAD_ARGS_NAME "system.dtb"
+#define CONFIG_SPL_FAT_LOAD_KERNEL_NAME "uImage"
+
+/* Not using MMC raw mode - just for compilation purpose */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0
+#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0
+
+/* qspi mode is working fine */
+#ifdef CONFIG_ZYNQ_QSPI
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_BUS 0
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x100000
+#define CONFIG_SPL_SPI_CS 0
+#endif
+
+/* for booting directly linux */
+#define CONFIG_SPL_OS_BOOT
+
+/* SP location before relocation, must use scratch RAM */
+#define CONFIG_SPL_TEXT_BASE 0x0
+
+/* 3 * 64kB blocks of OCM - one is on the top because of bootrom */
+#define CONFIG_SPL_MAX_SIZE 0x30000
+
+/* The highest 64k OCM address */
+#define OCM_HIGH_ADDR 0xffff0000
+
+/* Just define any reasonable size */
+#define CONFIG_SPL_STACK_SIZE 0x1000
+
+/* SPL stack position - and stack goes down */
+#define CONFIG_SPL_STACK (OCM_HIGH_ADDR + CONFIG_SPL_STACK_SIZE)
+
+/* On the top of OCM space */
+#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_STACK + \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x1000
+
+/* BSS setup */
+#define CONFIG_SPL_BSS_START_ADDR 0x100000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x100000
+
+#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
#endif /* __CONFIG_ZYNQ_COMMON_H */