#ifndef __CONFIG_ZYNQ_COMMON_H
#define __CONFIG_ZYNQ_COMMON_H
-/* High Level configuration Options */
-#define CONFIG_ARMV7
-#define CONFIG_ZYNQ
-
/* CPU clock */
#ifndef CONFIG_CPU_FREQ_HZ
# define CONFIG_CPU_FREQ_HZ 800000000
# define CONFIG_CMD_EXT2
# define CONFIG_FAT_WRITE
# define CONFIG_DOS_PARTITION
+# define CONFIG_CMD_EXT4
+# define CONFIG_CMD_EXT4_WRITE
#endif
#define CONFIG_SYS_I2C_ZYNQ
#define CONFIG_SYS_LONGHELP
#define CONFIG_CLOCKS
#define CONFIG_CMD_CLK
-#define CONFIG_SYS_MAXARGS 15 /* max number of command args */
+#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_FPGA_XILINX
#define CONFIG_FPGA_ZYNQPL
#define CONFIG_CMD_FPGA
+#define CONFIG_CMD_FPGA_LOADMK
+#define CONFIG_CMD_FPGA_LOADP
+#define CONFIG_CMD_FPGA_LOADBP
+#define CONFIG_CMD_FPGA_LOADFS
/* Open Firmware flat tree */
#define CONFIG_OF_LIBFDT
/* FIT support */
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
+#define CONFIG_IMAGE_FORMAT_LEGACY /* enable also legacy image format */
/* FDT support */
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
#define CONFIG_DISPLAY_BOARDINFO_LATE
/* RSA support */
#define CONFIG_CMD_TFTPPUT
/* SPL part */
-#define CONFIG_SPL
#define CONFIG_CMD_SPL
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/zynq/u-boot-spl.lds"
-/* Disable dcache for SPL just for sure */
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_DCACHE_OFF
-#undef CONFIG_FPGA
-#undef CONFIG_OF_CONTROL
-#endif
-
/* MMC support */
#ifdef CONFIG_ZYNQ_SDHCI0
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
-#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
+#define CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SPL_FAT_SUPPORT
-#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot-dtb.img"
+#endif
+
+/* Disable dcache for SPL just for sure */
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_DCACHE_OFF
+#undef CONFIG_FPGA
#endif
/* Address in RAM where the parameters must be copied by SPL. */
#define CONFIG_SYS_SPL_ARGS_ADDR 0x10000000
-#define CONFIG_SPL_FAT_LOAD_ARGS_NAME "system.dtb"
-#define CONFIG_SPL_FAT_LOAD_KERNEL_NAME "uImage"
+#define CONFIG_SPL_FS_LOAD_ARGS_NAME "system.dtb"
+#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
/* Not using MMC raw mode - just for compilation purpose */
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SPL_SPI_FLASH_SUPPORT
-#define CONFIG_SPL_SPI_BUS 0
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x100000
-#define CONFIG_SPL_SPI_CS 0
#endif
/* for booting directly linux */
#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_GENERIC_BOARD
+
#endif /* __CONFIG_ZYNQ_COMMON_H */