* Steven J. Hill <sjhill@realitydiluted.com>
* Thomas Gleixner <tglx@linutronix.de>
*
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
+ * SPDX-License-Identifier: GPL-2.0+
*
* Info:
* Contains standard defines and IDs for NAND flash devices
#ifndef __LINUX_MTD_NAND_H
#define __LINUX_MTD_NAND_H
+#define __UBOOT__
+#ifndef __UBOOT__
+#include <linux/wait.h>
+#include <linux/spinlock.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/flashchip.h>
+#include <linux/mtd/bbm.h>
+#else
#include "config.h"
#include "linux/compat.h"
#include "linux/mtd/mtd.h"
+#include "linux/mtd/flashchip.h"
#include "linux/mtd/bbm.h"
-
+#endif
struct mtd_info;
struct nand_flash_dev;
/* Scan and identify a NAND device */
-extern int nand_scan (struct mtd_info *mtd, int max_chips);
-/* Separate phases of nand_scan(), allowing board driver to intervene
- * and override command or ECC setup according to flash type */
+extern int nand_scan(struct mtd_info *mtd, int max_chips);
+/*
+ * Separate phases of nand_scan(), allowing board driver to intervene
+ * and override command or ECC setup according to flash type.
+ */
extern int nand_scan_ident(struct mtd_info *mtd, int max_chips,
- const struct nand_flash_dev *table);
+ struct nand_flash_dev *table);
extern int nand_scan_tail(struct mtd_info *mtd);
/* Free resources held by the NAND device */
/* Internal helper for board drivers which need to override command function */
extern void nand_wait_ready(struct mtd_info *mtd);
+#ifndef __UBOOT__
+/* locks all blocks present in the device */
+extern int nand_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len);
+
+/* unlocks specified locked blocks */
+extern int nand_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len);
+
+/* The maximum number of NAND chips in an array */
+#define NAND_MAX_CHIPS 8
+#endif
+
/*
* This constant declares the max. oobsize / page, which
* is supported now. If you add a chip with bigger oobsize/page
* adjust this accordingly.
*/
-#define NAND_MAX_OOBSIZE 640
+#define NAND_MAX_OOBSIZE 744
#define NAND_MAX_PAGESIZE 8192
/*
#define NAND_CMD_READOOB 0x50
#define NAND_CMD_ERASE1 0x60
#define NAND_CMD_STATUS 0x70
-#define NAND_CMD_STATUS_MULTI 0x71
#define NAND_CMD_SEQIN 0x80
#define NAND_CMD_RNDIN 0x85
#define NAND_CMD_READID 0x90
#define NAND_CMD_RESET 0xff
#define NAND_CMD_LOCK 0x2a
-#define NAND_CMD_LOCK_TIGHT 0x2c
#define NAND_CMD_UNLOCK1 0x23
#define NAND_CMD_UNLOCK2 0x24
-#define NAND_CMD_LOCK_STATUS 0x7a
/* Extended commands for large page devices */
#define NAND_CMD_READSTART 0x30
/* Chip has copy back function */
#define NAND_COPYBACK 0x00000010
/*
- * AND Chip which has 4 banks and a confusing page / block
- * assignment. See Renesas datasheet for further information.
+ * Chip requires ready check on read (for auto-incremented sequential read).
+ * True only for small page devices; large page devices do not support
+ * autoincrement.
*/
-#define NAND_IS_AND 0x00000020
-/*
- * Chip has a array of 4 pages which can be read without
- * additional ready /busy waits.
- */
-#define NAND_4PAGE_ARRAY 0x00000040
-/*
- * Chip requires that BBT is periodically rewritten to prevent
- * bits from adjacent blocks from 'leaking' in altering data.
- * This happens with the Renesas AG-AND chips, possibly others.
- */
-#define BBT_AUTO_REFRESH 0x00000080
+#define NAND_NEED_READRDY 0x00000100
+
/* Chip does not allow subpage writes */
#define NAND_NO_SUBPAGE_WRITE 0x00000200
#define NAND_ROM 0x00000800
/* Device supports subpage reads */
-#define NAND_SUBPAGE_READ 0x00001000
+#define NAND_SUBPAGE_READ 0x00001000
/* Options valid for Samsung large page devices */
-#define NAND_SAMSUNG_LP_OPTIONS \
- (NAND_NO_PADDING | NAND_CACHEPRG | NAND_COPYBACK)
+#define NAND_SAMSUNG_LP_OPTIONS NAND_CACHEPRG
/* Macros to identify the above */
-#define NAND_MUST_PAD(chip) (!(chip->options & NAND_NO_PADDING))
#define NAND_HAS_CACHEPROG(chip) ((chip->options & NAND_CACHEPRG))
-#define NAND_HAS_COPYBACK(chip) ((chip->options & NAND_COPYBACK))
#define NAND_HAS_SUBPAGE_READ(chip) ((chip->options & NAND_SUBPAGE_READ))
/* Non chip related options */
#define NAND_OWN_BUFFERS 0x00020000
/* Chip may not exist, so silence any errors in scan */
#define NAND_SCAN_SILENT_NODEV 0x00040000
+/*
+ * Autodetect nand buswidth with readid/onfi.
+ * This suppose the driver will configure the hardware in 8 bits mode
+ * when calling nand_scan_ident, and update its configuration
+ * before calling nand_scan_tail.
+ */
+#define NAND_BUSWIDTH_AUTO 0x00080000
/* Options set by nand scan */
/* bbt has already been read */
/* Cell info constants */
#define NAND_CI_CHIPNR_MSK 0x03
#define NAND_CI_CELLTYPE_MSK 0x0C
+#define NAND_CI_CELLTYPE_SHIFT 2
/* Keep gcc happy */
struct nand_chip;
+/* ONFI features */
+#define ONFI_FEATURE_16_BIT_BUS (1 << 0)
+#define ONFI_FEATURE_EXT_PARAM_PAGE (1 << 7)
+
/* ONFI timing mode, used in both asynchronous and synchronous mode */
#define ONFI_TIMING_MODE_0 (1 << 0)
#define ONFI_TIMING_MODE_1 (1 << 1)
/* ONFI feature address */
#define ONFI_FEATURE_ADDR_TIMING_MODE 0x1
+/* Vendor-specific feature address (Micron) */
+#define ONFI_FEATURE_ADDR_READ_RETRY 0x89
+
/* ONFI subfeature parameters length */
#define ONFI_SUBFEATURE_PARAM_LEN 4
+/* ONFI optional commands SET/GET FEATURES supported? */
+#define ONFI_OPT_CMD_SET_GET_FEATURES (1 << 2)
+
struct nand_onfi_params {
/* rev info and features block */
/* 'O' 'N' 'F' 'I' */
__le16 revision;
__le16 features;
__le16 opt_cmd;
- u8 reserved[22];
+ u8 reserved0[2];
+ __le16 ext_param_page_length; /* since ONFI 2.1 */
+ u8 num_of_param_pages; /* since ONFI 2.1 */
+ u8 reserved1[17];
/* manufacturer information block */
char manufacturer[12];
__le16 io_pin_capacitance_typ;
__le16 input_pin_capacitance_typ;
u8 input_pin_capacitance_max;
- u8 driver_strenght_support;
+ u8 driver_strength_support;
__le16 t_int_r;
__le16 t_ald;
u8 reserved4[7];
/* vendor */
- u8 reserved5[90];
+ __le16 vendor_revision;
+ u8 vendor[88];
__le16 crc;
-} __attribute__((packed));
+} __packed;
#define ONFI_CRC_BASE 0x4F4E
+/* Extended ECC information Block Definition (since ONFI 2.1) */
+struct onfi_ext_ecc_info {
+ u8 ecc_bits;
+ u8 codeword_size;
+ __le16 bb_per_lun;
+ __le16 block_endurance;
+ u8 reserved[2];
+} __packed;
+
+#define ONFI_SECTION_TYPE_0 0 /* Unused section. */
+#define ONFI_SECTION_TYPE_1 1 /* for additional sections. */
+#define ONFI_SECTION_TYPE_2 2 /* for ECC information. */
+struct onfi_ext_section {
+ u8 type;
+ u8 length;
+} __packed;
+
+#define ONFI_EXT_SECTION_MAX 8
+
+/* Extended Parameter Page Definition (since ONFI 2.1) */
+struct onfi_ext_param_page {
+ __le16 crc;
+ u8 sig[4]; /* 'E' 'P' 'P' 'S' */
+ u8 reserved0[10];
+ struct onfi_ext_section sections[ONFI_EXT_SECTION_MAX];
+
+ /*
+ * The actual size of the Extended Parameter Page is in
+ * @ext_param_page_length of nand_onfi_params{}.
+ * The following are the variable length sections.
+ * So we do not add any fields below. Please see the ONFI spec.
+ */
+} __packed;
+
+struct nand_onfi_vendor_micron {
+ u8 two_plane_read;
+ u8 read_cache;
+ u8 read_unique_id;
+ u8 dq_imped;
+ u8 dq_imped_num_settings;
+ u8 dq_imped_feat_addr;
+ u8 rb_pulldown_strength;
+ u8 rb_pulldown_strength_feat_addr;
+ u8 rb_pulldown_strength_num_settings;
+ u8 otp_mode;
+ u8 otp_page_start;
+ u8 otp_data_prot_addr;
+ u8 otp_num_pages;
+ u8 otp_feat_addr;
+ u8 read_retry_options;
+ u8 reserved[72];
+ u8 param_revision;
+} __packed;
+
/**
* struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independent devices
* @lock: protection lock
* when a hw controller is available.
*/
struct nand_hw_control {
-/* XXX U-BOOT XXX */
-#if 0
- spinlock_t lock;
+ spinlock_t lock;
+ struct nand_chip *active;
+#ifndef __UBOOT__
wait_queue_head_t wq;
#endif
- struct nand_chip *active;
};
/**
* any single ECC step, 0 if bitflips uncorrectable, -EIO hw error
* @read_subpage: function to read parts of the page covered by ECC;
* returns same as read_page()
+ * @write_subpage: function to write parts of the page covered by ECC.
* @write_page: function to write a page according to the ECC generator
* requirements.
* @write_oob_raw: function to write chip OOB data without ECC
uint8_t *buf, int oob_required, int page);
int (*read_subpage)(struct mtd_info *mtd, struct nand_chip *chip,
uint32_t offs, uint32_t len, uint8_t *buf);
+ int (*write_subpage)(struct mtd_info *mtd, struct nand_chip *chip,
+ uint32_t offset, uint32_t data_len,
+ const uint8_t *data_buf, int oob_required);
int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip,
const uint8_t *buf, int oob_required);
int (*write_oob_raw)(struct mtd_info *mtd, struct nand_chip *chip,
* consecutive order.
*/
struct nand_buffers {
+#ifndef __UBOOT__
+ uint8_t *ecccalc;
+ uint8_t *ecccode;
+ uint8_t *databuf;
+#else
uint8_t ecccalc[ALIGN(NAND_MAX_OOBSIZE, ARCH_DMA_MINALIGN)];
uint8_t ecccode[ALIGN(NAND_MAX_OOBSIZE, ARCH_DMA_MINALIGN)];
uint8_t databuf[ALIGN(NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE,
ARCH_DMA_MINALIGN)];
+#endif
};
/**
* flash device.
* @read_byte: [REPLACEABLE] read one byte from the chip
* @read_word: [REPLACEABLE] read one word from the chip
+ * @write_byte: [REPLACEABLE] write a single byte to the chip on the
+ * low 8 I/O lines
* @write_buf: [REPLACEABLE] write data from the buffer to the chip
* @read_buf: [REPLACEABLE] read data from the chip into the buffer
- * @verify_buf: [REPLACEABLE] verify buffer contents against the chip
- * data.
* @select_chip: [REPLACEABLE] select chip nr
- * @block_bad: [REPLACEABLE] check, if the block is bad
- * @block_markbad: [REPLACEABLE] mark the block bad
+ * @block_bad: [REPLACEABLE] check if a block is bad, using OOB markers
+ * @block_markbad: [REPLACEABLE] mark a block bad
* @cmd_ctrl: [BOARDSPECIFIC] hardwarespecific function for controlling
* ALE/CLE/nCE. Also used to write command and address
* @init_size: [BOARDSPECIFIC] hardwarespecific function for setting
* commands to the chip.
* @waitfunc: [REPLACEABLE] hardwarespecific function for wait on
* ready.
+ * @setup_read_retry: [FLASHSPECIFIC] flash (vendor) specific function for
+ * setting the read-retry mode. Mostly needed for MLC NAND.
* @ecc: [BOARDSPECIFIC] ECC control structure
* @buffers: buffer structure for read/write
* @hwcontrol: platform-specific hardware control structure
* @badblockbits: [INTERN] minimum number of set bits in a good block's
* bad block marker position; i.e., BBM == 11110111b is
* not bad when badblockbits == 7
- * @cellinfo: [INTERN] MLC/multichip data from chip ident
+ * @bits_per_cell: [INTERN] number of bits per cell. i.e., 1 means SLC.
+ * @ecc_strength_ds: [INTERN] ECC correctability from the datasheet.
+ * Minimum amount of bit errors per @ecc_step_ds guaranteed
+ * to be correctable. If unknown, set to zero.
+ * @ecc_step_ds: [INTERN] ECC step required by the @ecc_strength_ds,
+ * also from the datasheet. It is the recommended ECC step
+ * size, if known; if unknown, set to zero.
* @numchips: [INTERN] number of physical chips
* @chipsize: [INTERN] the size of one chip for multichip arrays
* @pagemask: [INTERN] page number mask = number of (pages / chip) - 1
* @pagebuf: [INTERN] holds the pagenumber which is currently in
* data_buf.
+ * @pagebuf_bitflips: [INTERN] holds the bitflip count for the page which is
+ * currently in data_buf.
* @subpagesize: [INTERN] holds the subpagesize
* @onfi_version: [INTERN] holds the chip ONFI version (BCD encoded),
* non 0 if ONFI supported.
* @onfi_params: [INTERN] holds the ONFI page parameter when ONFI is
* supported, 0 otherwise.
- * @onfi_set_features [REPLACEABLE] set the features for ONFI nand
- * @onfi_get_features [REPLACEABLE] get the features for ONFI nand
- * @ecclayout: [REPLACEABLE] the default ECC placement scheme
+ * @read_retries: [INTERN] the number of read retry modes supported
+ * @onfi_set_features: [REPLACEABLE] set the features for ONFI nand
+ * @onfi_get_features: [REPLACEABLE] get the features for ONFI nand
* @bbt: [INTERN] bad block table pointer
* @bbt_td: [REPLACEABLE] bad block table descriptor for flash
* lookup.
uint8_t (*read_byte)(struct mtd_info *mtd);
u16 (*read_word)(struct mtd_info *mtd);
+ void (*write_byte)(struct mtd_info *mtd, uint8_t byte);
void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len);
void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len);
- int (*verify_buf)(struct mtd_info *mtd, const uint8_t *buf, int len);
+#ifdef __UBOOT__
+#if defined(CONFIG_MTD_NAND_VERIFY_WRITE)
+ int (*verify_buf)(struct mtd_info *mtd, const uint8_t *buf, int len);
+#endif
+#endif
void (*select_chip)(struct mtd_info *mtd, int chip);
int (*block_bad)(struct mtd_info *mtd, loff_t ofs, int getchip);
int (*block_markbad)(struct mtd_info *mtd, loff_t ofs);
int (*errstat)(struct mtd_info *mtd, struct nand_chip *this, int state,
int status, int page);
int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip,
- const uint8_t *buf, int oob_required, int page,
- int cached, int raw);
+ uint32_t offset, int data_len, const uint8_t *buf,
+ int oob_required, int page, int cached, int raw);
int (*onfi_set_features)(struct mtd_info *mtd, struct nand_chip *chip,
int feature_addr, uint8_t *subfeature_para);
int (*onfi_get_features)(struct mtd_info *mtd, struct nand_chip *chip,
int feature_addr, uint8_t *subfeature_para);
+ int (*setup_read_retry)(struct mtd_info *mtd, int retry_mode);
int chip_delay;
unsigned int options;
uint64_t chipsize;
int pagemask;
int pagebuf;
+ unsigned int pagebuf_bitflips;
int subpagesize;
- uint8_t cellinfo;
+ uint8_t bits_per_cell;
+ uint16_t ecc_strength_ds;
+ uint16_t ecc_step_ds;
int badblockpos;
int badblockbits;
int onfi_version;
#ifdef CONFIG_SYS_NAND_ONFI_DETECTION
- struct nand_onfi_params onfi_params;
+ struct nand_onfi_params onfi_params;
#endif
- int state;
+ int read_retries;
+
+ flstate_t state;
uint8_t *oob_poi;
struct nand_hw_control *controller;
+#ifdef __UBOOT__
struct nand_ecclayout *ecclayout;
+#endif
struct nand_ecc_ctrl ecc;
struct nand_buffers *buffers;
#define NAND_MFR_AMD 0x01
#define NAND_MFR_MACRONIX 0xc2
#define NAND_MFR_EON 0x92
+#define NAND_MFR_SANDISK 0x45
+#define NAND_MFR_INTEL 0x89
+
+/* The maximum expected count of bytes in the NAND ID sequence */
+#define NAND_MAX_ID_LEN 8
+
+/*
+ * A helper for defining older NAND chips where the second ID byte fully
+ * defined the chip, including the geometry (chip size, eraseblock size, page
+ * size). All these chips have 512 bytes NAND page size.
+ */
+#define LEGACY_ID_NAND(nm, devid, chipsz, erasesz, opts) \
+ { .name = (nm), {{ .dev_id = (devid) }}, .pagesize = 512, \
+ .chipsize = (chipsz), .erasesize = (erasesz), .options = (opts) }
+
+/*
+ * A helper for defining newer chips which report their page size and
+ * eraseblock size via the extended ID bytes.
+ *
+ * The real difference between LEGACY_ID_NAND and EXTENDED_ID_NAND is that with
+ * EXTENDED_ID_NAND, manufacturers overloaded the same device ID so that the
+ * device ID now only represented a particular total chip size (and voltage,
+ * buswidth), and the page size, eraseblock size, and OOB size could vary while
+ * using the same device ID.
+ */
+#define EXTENDED_ID_NAND(nm, devid, chipsz, opts) \
+ { .name = (nm), {{ .dev_id = (devid) }}, .chipsize = (chipsz), \
+ .options = (opts) }
+
+#define NAND_ECC_INFO(_strength, _step) \
+ { .strength_ds = (_strength), .step_ds = (_step) }
+#define NAND_ECC_STRENGTH(type) ((type)->ecc.strength_ds)
+#define NAND_ECC_STEP(type) ((type)->ecc.step_ds)
/**
* struct nand_flash_dev - NAND Flash Device ID Structure
- * @name: Identify the device type
- * @id: device ID code
- * @pagesize: Pagesize in bytes. Either 256 or 512 or 0
- * If the pagesize is 0, then the real pagesize
- * and the eraseize are determined from the
- * extended id bytes in the chip
- * @erasesize: Size of an erase block in the flash device.
- * @chipsize: Total chipsize in Mega Bytes
- * @options: Bitfield to store chip relevant options
+ * @name: a human-readable name of the NAND chip
+ * @dev_id: the device ID (the second byte of the full chip ID array)
+ * @mfr_id: manufecturer ID part of the full chip ID array (refers the same
+ * memory address as @id[0])
+ * @dev_id: device ID part of the full chip ID array (refers the same memory
+ * address as @id[1])
+ * @id: full device ID array
+ * @pagesize: size of the NAND page in bytes; if 0, then the real page size (as
+ * well as the eraseblock size) is determined from the extended NAND
+ * chip ID array)
+ * @chipsize: total chip size in MiB
+ * @erasesize: eraseblock size in bytes (determined from the extended ID if 0)
+ * @options: stores various chip bit options
+ * @id_len: The valid length of the @id.
+ * @oobsize: OOB size
+ * @ecc.strength_ds: The ECC correctability from the datasheet, same as the
+ * @ecc_strength_ds in nand_chip{}.
+ * @ecc.step_ds: The ECC step required by the @ecc.strength_ds, same as the
+ * @ecc_step_ds in nand_chip{}, also from the datasheet.
+ * For example, the "4bit ECC for each 512Byte" can be set with
+ * NAND_ECC_INFO(4, 512).
*/
struct nand_flash_dev {
char *name;
- int id;
- unsigned long pagesize;
- unsigned long chipsize;
- unsigned long erasesize;
- unsigned long options;
+ union {
+ struct {
+ uint8_t mfr_id;
+ uint8_t dev_id;
+ };
+ uint8_t id[NAND_MAX_ID_LEN];
+ };
+ unsigned int pagesize;
+ unsigned int chipsize;
+ unsigned int erasesize;
+ unsigned int options;
+ uint16_t id_len;
+ uint16_t oobsize;
+ struct {
+ uint16_t strength_ds;
+ uint16_t step_ds;
+ } ecc;
};
/**
char *name;
};
-extern const struct nand_flash_dev nand_flash_ids[];
-extern const struct nand_manufacturers nand_manuf_ids[];
+extern struct nand_flash_dev nand_flash_ids[];
+extern struct nand_manufacturers nand_manuf_ids[];
extern int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd);
-extern int nand_update_bbt(struct mtd_info *mtd, loff_t offs);
extern int nand_default_bbt(struct mtd_info *mtd);
+extern int nand_markbad_bbt(struct mtd_info *mtd, loff_t offs);
extern int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt);
extern int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
int allowbbt);
extern int nand_do_read(struct mtd_info *mtd, loff_t from, size_t len,
size_t *retlen, uint8_t *buf);
+#ifdef __UBOOT__
/*
* Constants for oob configuration
*/
#define NAND_SMALL_BADBLOCK_POS 5
#define NAND_LARGE_BADBLOCK_POS 0
+#endif
/**
* struct platform_nand_chip - chip level device structure
/**
* struct platform_nand_ctrl - controller level device structure
+ * @probe: platform specific function to probe/setup hardware
+ * @remove: platform specific function to remove/teardown hardware
* @hwcontrol: platform specific hardware control structure
* @dev_ready: platform specific function to read ready/busy pin
* @select_chip: platform specific chip select function
* @cmd_ctrl: platform specific function for controlling
* ALE/CLE/nCE. Also used to write command and address
+ * @write_buf: platform specific function for write buffer
+ * @read_buf: platform specific function for read buffer
+ * @read_byte: platform specific function to read one byte from chip
* @priv: private data to transport driver specific settings
*
* All fields are optional and depend on the hardware driver requirements
*/
struct platform_nand_ctrl {
+ int (*probe)(struct platform_device *pdev);
+ void (*remove)(struct platform_device *pdev);
void (*hwcontrol)(struct mtd_info *mtd, int cmd);
int (*dev_ready)(struct mtd_info *mtd);
void (*select_chip)(struct mtd_info *mtd, int chip);
void (*cmd_ctrl)(struct mtd_info *mtd, int dat, unsigned int ctrl);
+ void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len);
+ void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len);
unsigned char (*read_byte)(struct mtd_info *mtd);
void *priv;
};
return chip->priv;
}
-/* Standard NAND functions from nand_base.c */
-void nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len);
-void nand_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len);
-void nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len);
-void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len);
-uint8_t nand_read_byte(struct mtd_info *mtd);
+#ifdef CONFIG_SYS_NAND_ONFI_DETECTION
+/* return the supported features. */
+static inline int onfi_feature(struct nand_chip *chip)
+{
+ return chip->onfi_version ? le16_to_cpu(chip->onfi_params.features) : 0;
+}
/* return the supported asynchronous timing mode. */
-
-#ifdef CONFIG_SYS_NAND_ONFI_DETECTION
static inline int onfi_get_async_timing_mode(struct nand_chip *chip)
{
if (!chip->onfi_version)
}
#endif
+/*
+ * Check if it is a SLC nand.
+ * The !nand_is_slc() can be used to check the MLC/TLC nand chips.
+ * We do not distinguish the MLC and TLC now.
+ */
+static inline bool nand_is_slc(struct nand_chip *chip)
+{
+ return chip->bits_per_cell == 1;
+}
+
+/**
+ * Check if the opcode's address should be sent only on the lower 8 bits
+ * @command: opcode to check
+ */
+static inline int nand_opcode_8bits(unsigned int command)
+{
+ switch (command) {
+ case NAND_CMD_READID:
+ case NAND_CMD_PARAM:
+ case NAND_CMD_GET_FEATURES:
+ case NAND_CMD_SET_FEATURES:
+ return 1;
+ default:
+ break;
+ }
+ return 0;
+}
+
+#ifdef __UBOOT__
+/* Standard NAND functions from nand_base.c */
+void nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len);
+void nand_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len);
+void nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len);
+void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len);
+uint8_t nand_read_byte(struct mtd_info *mtd);
+#endif
#endif /* __LINUX_MTD_NAND_H */
projects / u-boot / blobdiff