ARCH_DMA_MINALIGN)];
};
+/**
+ * struct nand_sdr_timings - SDR NAND chip timings
+ *
+ * This struct defines the timing requirements of a SDR NAND chip.
+ * These information can be found in every NAND datasheets and the timings
+ * meaning are described in the ONFI specifications:
+ * www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf (chapter 4.15 Timing
+ * Parameters)
+ *
+ * All these timings are expressed in picoseconds.
+ *
+ * @tALH_min: ALE hold time
+ * @tADL_min: ALE to data loading time
+ * @tALS_min: ALE setup time
+ * @tAR_min: ALE to RE# delay
+ * @tCEA_max: CE# access time
+ * @tCEH_min: CE# high hold time
+ * @tCH_min: CE# hold time
+ * @tCHZ_max: CE# high to output hi-Z
+ * @tCLH_min: CLE hold time
+ * @tCLR_min: CLE to RE# delay
+ * @tCLS_min: CLE setup time
+ * @tCOH_min: CE# high to output hold
+ * @tCS_min: CE# setup time
+ * @tDH_min: Data hold time
+ * @tDS_min: Data setup time
+ * @tFEAT_max: Busy time for Set Features and Get Features
+ * @tIR_min: Output hi-Z to RE# low
+ * @tITC_max: Interface and Timing Mode Change time
+ * @tRC_min: RE# cycle time
+ * @tREA_max: RE# access time
+ * @tREH_min: RE# high hold time
+ * @tRHOH_min: RE# high to output hold
+ * @tRHW_min: RE# high to WE# low
+ * @tRHZ_max: RE# high to output hi-Z
+ * @tRLOH_min: RE# low to output hold
+ * @tRP_min: RE# pulse width
+ * @tRR_min: Ready to RE# low (data only)
+ * @tRST_max: Device reset time, measured from the falling edge of R/B# to the
+ * rising edge of R/B#.
+ * @tWB_max: WE# high to SR[6] low
+ * @tWC_min: WE# cycle time
+ * @tWH_min: WE# high hold time
+ * @tWHR_min: WE# high to RE# low
+ * @tWP_min: WE# pulse width
+ * @tWW_min: WP# transition to WE# low
+ */
+struct nand_sdr_timings {
+ u32 tALH_min;
+ u32 tADL_min;
+ u32 tALS_min;
+ u32 tAR_min;
+ u32 tCEA_max;
+ u32 tCEH_min;
+ u32 tCH_min;
+ u32 tCHZ_max;
+ u32 tCLH_min;
+ u32 tCLR_min;
+ u32 tCLS_min;
+ u32 tCOH_min;
+ u32 tCS_min;
+ u32 tDH_min;
+ u32 tDS_min;
+ u32 tFEAT_max;
+ u32 tIR_min;
+ u32 tITC_max;
+ u32 tRC_min;
+ u32 tREA_max;
+ u32 tREH_min;
+ u32 tRHOH_min;
+ u32 tRHW_min;
+ u32 tRHZ_max;
+ u32 tRLOH_min;
+ u32 tRP_min;
+ u32 tRR_min;
+ u64 tRST_max;
+ u32 tWB_max;
+ u32 tWC_min;
+ u32 tWH_min;
+ u32 tWHR_min;
+ u32 tWP_min;
+ u32 tWW_min;
+};
+
+/**
+ * enum nand_data_interface_type - NAND interface timing type
+ * @NAND_SDR_IFACE: Single Data Rate interface
+ */
+enum nand_data_interface_type {
+ NAND_SDR_IFACE,
+};
+
+/**
+ * struct nand_data_interface - NAND interface timing
+ * @type: type of the timing
+ * @timings: The timing, type according to @type
+ */
+struct nand_data_interface {
+ enum nand_data_interface_type type;
+ union {
+ struct nand_sdr_timings sdr;
+ } timings;
+};
+
+/**
+ * nand_get_sdr_timings - get SDR timing from data interface
+ * @conf: The data interface
+ */
+static inline const struct nand_sdr_timings *
+nand_get_sdr_timings(const struct nand_data_interface *conf)
+{
+ if (conf->type != NAND_SDR_IFACE)
+ return ERR_PTR(-EINVAL);
+
+ return &conf->timings.sdr;
+}
+
/**
* struct nand_chip - NAND Private Flash Chip Data
* @mtd: MTD device registered to the MTD framework
}
#endif
+int onfi_init_data_interface(struct nand_chip *chip,
+ struct nand_data_interface *iface,
+ enum nand_data_interface_type type,
+ int timing_mode);
+
/*
* Check if it is a SLC nand.
* The !nand_is_slc() can be used to check the MLC/TLC nand chips.
void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len);
uint8_t nand_read_byte(struct mtd_info *mtd);
-/*
- * struct nand_sdr_timings - SDR NAND chip timings
- *
- * This struct defines the timing requirements of a SDR NAND chip.
- * These informations can be found in every NAND datasheets and the timings
- * meaning are described in the ONFI specifications:
- * www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf (chapter 4.15 Timing
- * Parameters)
- *
- * All these timings are expressed in picoseconds.
- */
-
-struct nand_sdr_timings {
- u32 tALH_min;
- u32 tADL_min;
- u32 tALS_min;
- u32 tAR_min;
- u32 tCEA_max;
- u32 tCEH_min;
- u32 tCH_min;
- u32 tCHZ_max;
- u32 tCLH_min;
- u32 tCLR_min;
- u32 tCLS_min;
- u32 tCOH_min;
- u32 tCS_min;
- u32 tDH_min;
- u32 tDS_min;
- u32 tFEAT_max;
- u32 tIR_min;
- u32 tITC_max;
- u32 tRC_min;
- u32 tREA_max;
- u32 tREH_min;
- u32 tRHOH_min;
- u32 tRHW_min;
- u32 tRHZ_max;
- u32 tRLOH_min;
- u32 tRP_min;
- u32 tRR_min;
- u64 tRST_max;
- u32 tWB_max;
- u32 tWC_min;
- u32 tWH_min;
- u32 tWHR_min;
- u32 tWP_min;
- u32 tWW_min;
-};
-
/* get timing characteristics from ONFI timing mode. */
const struct nand_sdr_timings *onfi_async_timing_mode_to_sdr_timings(int mode);
void *ecc, int ecclen,
void *extraoob, int extraooblen,
int threshold);
+
+/* Reset and initialize a NAND device */
+int nand_reset(struct nand_chip *chip);
+
#endif /* __LINUX_MTD_NAND_H */
projects / u-boot / blobdiff