#define UNUSABLE_ERR -17 /* Unusable Card */
#define COMM_ERR -18 /* Communications Error */
#define TIMEOUT -19
+#define IN_PROGRESS -20 /* operation is in progress */
#define MMC_CMD_GO_IDLE_STATE 0
#define MMC_CMD_SEND_OP_COND 1
/*
* EXT_CSD fields
*/
+#define EXT_CSD_GP_SIZE_MULT 143 /* R/W */
#define EXT_CSD_PARTITIONING_SUPPORT 160 /* RO */
+#define EXT_CSD_RPMB_MULT 168 /* RO */
#define EXT_CSD_ERASE_GROUP_DEF 175 /* R/W */
#define EXT_CSD_BOOT_BUS_WIDTH 177
#define EXT_CSD_PART_CONF 179 /* R/W */
#define EXT_CSD_REV 192 /* RO */
#define EXT_CSD_CARD_TYPE 196 /* RO */
#define EXT_CSD_SEC_CNT 212 /* RO, 4 bytes */
+#define EXT_CSD_HC_WP_GRP_SIZE 221 /* RO */
#define EXT_CSD_HC_ERASE_GRP_SIZE 224 /* RO */
#define EXT_CSD_BOOT_MULT 226 /* RO */
uint write_bl_len;
uint erase_grp_size;
u64 capacity;
+ u64 capacity_user;
+ u64 capacity_boot;
+ u64 capacity_rpmb;
+ u64 capacity_gp[4];
block_dev_desc_t block_dev;
int (*send_cmd)(struct mmc *mmc,
struct mmc_cmd *cmd, struct mmc_data *data);
int (*getcd)(struct mmc *mmc);
int (*getwp)(struct mmc *mmc);
uint b_max;
+ char op_cond_pending; /* 1 if we are waiting on an op_cond command */
+ char init_in_progress; /* 1 if we have done mmc_start_init() */
+ char preinit; /* start init as early as possible */
+ uint op_cond_response; /* the response byte from the last op_cond */
};
int mmc_register(struct mmc *mmc);
/* Function to send commands to open/close the specified boot partition */
int mmc_boot_part_access(struct mmc *mmc, u8 ack, u8 part_num, u8 access);
+/**
+ * Start device initialization and return immediately; it does not block on
+ * polling OCR (operation condition register) status. Then you should call
+ * mmc_init, which would block on polling OCR status and complete the device
+ * initializatin.
+ *
+ * @param mmc Pointer to a MMC device struct
+ * @return 0 on success, IN_PROGRESS on waiting for OCR status, <0 on error.
+ */
+int mmc_start_init(struct mmc *mmc);
+
+/**
+ * Set preinit flag of mmc device.
+ *
+ * This will cause the device to be pre-inited during mmc_initialize(),
+ * which may save boot time if the device is not accessed until later.
+ * Some eMMC devices take 200-300ms to init, but unfortunately they
+ * must be sent a series of commands to even get them to start preparing
+ * for operation.
+ *
+ * @param mmc Pointer to a MMC device struct
+ * @param preinit preinit flag value
+ */
+void mmc_set_preinit(struct mmc *mmc, int preinit);
+
#ifdef CONFIG_GENERIC_MMC
#define mmc_host_is_spi(mmc) ((mmc)->host_caps & MMC_MODE_SPI)
struct mmc *mmc_spi_init(uint bus, uint cs, uint speed, uint mode);