#include <linux/list.h>
#include <linux/compiler.h>
+#include <part.h>
#define SD_VERSION_SD 0x20000
#define SD_VERSION_3 (SD_VERSION_SD | 0x300)
#define COMM_ERR -18 /* Communications Error */
#define TIMEOUT -19
#define IN_PROGRESS -20 /* operation is in progress */
+#define SWITCH_ERR -21 /* Card reports failure to switch mode */
#define MMC_CMD_GO_IDLE_STATE 0
#define MMC_CMD_SEND_OP_COND 1
#define MMC_CMD_SET_BLOCKLEN 16
#define MMC_CMD_READ_SINGLE_BLOCK 17
#define MMC_CMD_READ_MULTIPLE_BLOCK 18
+#define MMC_CMD_SET_BLOCK_COUNT 23
#define MMC_CMD_WRITE_SINGLE_BLOCK 24
#define MMC_CMD_WRITE_MULTIPLE_BLOCK 25
#define MMC_CMD_ERASE_GROUP_START 35
#define SECURE_ERASE 0x80000000
#define MMC_STATUS_MASK (~0x0206BF7F)
+#define MMC_STATUS_SWITCH_ERROR (1 << 7)
#define MMC_STATUS_RDY_FOR_DATA (1 << 8)
#define MMC_STATUS_CURR_STATE (0xf << 9)
#define MMC_STATUS_ERROR (1 << 19)
#define EXT_CSD_GP_SIZE_MULT 143 /* R/W */
#define EXT_CSD_PARTITIONS_ATTRIBUTE 156 /* R/W */
#define EXT_CSD_PARTITIONING_SUPPORT 160 /* RO */
+#define EXT_CSD_RST_N_FUNCTION 162 /* R/W */
#define EXT_CSD_RPMB_MULT 168 /* RO */
#define EXT_CSD_ERASE_GROUP_DEF 175 /* R/W */
#define EXT_CSD_BOOT_BUS_WIDTH 177
* boot partitions (2), general purpose partitions (4) in MMC v4.4.
*/
#define MMC_NUM_BOOT_PARTITION 2
+#define MMC_PART_RPMB 3 /* RPMB partition number */
struct mmc_cid {
unsigned long psn;
int mmc_set_part_conf(struct mmc *mmc, u8 ack, u8 part_num, u8 access);
/* Function to modify the BOOT_BUS_WIDTH field of EXT_CSD */
int mmc_set_boot_bus_width(struct mmc *mmc, u8 width, u8 reset, u8 mode);
-
+/* Function to modify the RST_n_FUNCTION field of EXT_CSD */
+int mmc_set_rst_n_function(struct mmc *mmc, u8 enable);
+/* Functions to read / write the RPMB partition */
+int mmc_rpmb_set_key(struct mmc *mmc, void *key);
+int mmc_rpmb_get_counter(struct mmc *mmc, unsigned long *counter);
+int mmc_rpmb_read(struct mmc *mmc, void *addr, unsigned short blk,
+ unsigned short cnt, unsigned char *key);
+int mmc_rpmb_write(struct mmc *mmc, void *addr, unsigned short blk,
+ unsigned short cnt, unsigned char *key);
/**
* Start device initialization and return immediately; it does not block on
* polling OCR (operation condition register) status. Then you should call
#ifdef CONFIG_GENERIC_MMC
#ifdef CONFIG_MMC_SPI
-#define mmc_host_is_spi(mmc) ((mmc)->cfg.host_caps & MMC_MODE_SPI)
+#define mmc_host_is_spi(mmc) ((mmc)->cfg->host_caps & MMC_MODE_SPI)
#else
#define mmc_host_is_spi(mmc) 0
#endif
int mmc_legacy_init(int verbose);
#endif
+int board_mmc_init(bd_t *bis);
+
/* Set block count limit because of 16 bit register limit on some hardware*/
#ifndef CONFIG_SYS_MMC_MAX_BLK_COUNT
#define CONFIG_SYS_MMC_MAX_BLK_COUNT 65535