* is used to access memory mapped resources and is called a MEM-AP. Also a
* JTAG-AP is also defined, bridging to JTAG resources; those are uncommon.
*
- * @todo Remove modality (queued/nonqueued, via DAP trans_mode) from all
- * procedure interfaces. Modal programming interfaces are very error prone.
- * Procedures should be either queued, or synchronous. Otherwise input
- * and output constraints are context-sensitive, and it's hard to know
- * what a block of code will do just by reading it.
+ * This programming interface allows DAP pipelined operations through a
+ * transaction queue. This primarily affects AP operations (such as using
+ * a MEM-AP to access memory or registers). If the current transaction has
+ * not finished by the time the next one must begin, and the ORUNDETECT bit
+ * is set in the DP_CTRL_STAT register, the SSTICKYORUN status is set and
+ * further AP operations will fail. There are two basic methods to avoid
+ * such overrun errors. One involves polling for status instead of using
+ * transaction piplining. The other involves adding delays to ensure the
+ * AP has enough time to complete one operation before starting the next
+ * one. (For JTAG these delays are controlled by memaccess_tck.)
*/
/*
#include "config.h"
#endif
+#include "arm.h"
#include "arm_adi_v5.h"
#include <helper/time_support.h>
-/*
- * Transaction Mode:
- * swjdp->trans_mode = TRANS_MODE_COMPOSITE;
- * Uses Overrun checking mode and does not do actual JTAG send/receive or transaction
- * result checking until swjdp_end_transaction()
- * This must be done before using or deallocating any return variables.
- * swjdp->trans_mode == TRANS_MODE_ATOMIC
- * All reads and writes to the AHB bus are checked for valid completion, and return values
- * are immediatley available.
-*/
-
/* ARM ADI Specification requires at least 10 bits used for TAR autoincrement */
* @param invalue NULL, or points to a 32-bit (little-endian) integer
* @param ack points to where the three bit JTAG_ACK_* code will be stored
*/
-static int adi_jtag_dp_scan(struct swjdp_common *swjdp,
+static int adi_jtag_dp_scan(struct adiv5_dap *swjdp,
uint8_t instr, uint8_t reg_addr, uint8_t RnW,
uint8_t *outvalue, uint8_t *invalue, uint8_t *ack)
{
jtag_set_end_state(TAP_IDLE);
arm_jtag_set_instr(jtag_info, instr, NULL);
- /* Add specified number of tck clocks before accessing memory bus */
-
- /* REVISIT these TCK cycles should be *AFTER* updating APACC, since
- * they provide more time for the (MEM) AP to complete the read ...
- * See "Minimum Response Time" for JTAG-DP, in the ADIv5 spec.
- */
- if ((instr == JTAG_DP_APACC)
- && ((reg_addr == AP_REG_DRW)
- || ((reg_addr & 0xF0) == AP_REG_BD0))
- && (swjdp->memaccess_tck != 0))
- jtag_add_runtest(swjdp->memaccess_tck, jtag_set_end_state(TAP_IDLE));
-
/* Scan out a read or write operation using some DP or AP register.
* For APACC access with any sticky error flag set, this is discarded.
*/
- fields[0].tap = jtag_info->tap;
fields[0].num_bits = 3;
buf_set_u32(&out_addr_buf, 0, 3, ((reg_addr >> 1) & 0x6) | (RnW & 0x1));
fields[0].out_value = &out_addr_buf;
* When overrun detect is active, STICKYORUN is set.
*/
- fields[1].tap = jtag_info->tap;
fields[1].num_bits = 32;
fields[1].out_value = outvalue;
fields[1].in_value = invalue;
- jtag_add_dr_scan(2, fields, jtag_get_end_state());
+ jtag_add_dr_scan(jtag_info->tap, 2, fields, jtag_get_end_state());
+
+ /* Add specified number of tck clocks after starting memory bus
+ * access, giving the hardware time to complete the access.
+ * They provide more time for the (MEM) AP to complete the read ...
+ * See "Minimum Response Time" for JTAG-DP, in the ADIv5 spec.
+ */
+ if ((instr == JTAG_DP_APACC)
+ && ((reg_addr == AP_REG_DRW)
+ || ((reg_addr & 0xF0) == AP_REG_BD0))
+ && (swjdp->memaccess_tck != 0))
+ jtag_add_runtest(swjdp->memaccess_tck,
+ jtag_set_end_state(TAP_IDLE));
return jtag_get_error();
}
* conversions are performed (so the types of invalue and outvalue
* must be different).
*/
-static int adi_jtag_dp_scan_u32(struct swjdp_common *swjdp,
+static int adi_jtag_dp_scan_u32(struct adiv5_dap *swjdp,
uint8_t instr, uint8_t reg_addr, uint8_t RnW,
uint32_t outvalue, uint32_t *invalue, uint8_t *ack)
{
/**
* Utility to write AP registers.
*/
-static int ap_write_check(struct swjdp_common *dap,
+static inline int adi_jtag_ap_write_check(struct adiv5_dap *dap,
uint8_t reg_addr, uint8_t *outvalue)
{
- adi_jtag_dp_scan(dap, JTAG_DP_APACC, reg_addr, DPAP_WRITE,
+ return adi_jtag_dp_scan(dap, JTAG_DP_APACC, reg_addr, DPAP_WRITE,
outvalue, NULL, NULL);
-
- /* REVISIT except in dap_setup_accessport() almost all call paths
- * set up COMPOSITE. Probably worth just inlining the scan...
- */
-
- /* In TRANS_MODE_ATOMIC all JTAG_DP_APACC transactions wait for
- * ack = OK/FAULT and the check CTRL_STAT
- */
- if (dap->trans_mode == TRANS_MODE_ATOMIC)
- return jtagdp_transaction_endcheck(dap);
-
- return ERROR_OK;
}
-static int scan_inout_check_u32(struct swjdp_common *swjdp,
+static int adi_jtag_scan_inout_check_u32(struct adiv5_dap *swjdp,
uint8_t instr, uint8_t reg_addr, uint8_t RnW,
uint32_t outvalue, uint32_t *invalue)
{
+ int retval;
+
/* Issue the read or write */
- adi_jtag_dp_scan_u32(swjdp, instr, reg_addr, RnW, outvalue, NULL, NULL);
+ retval = adi_jtag_dp_scan_u32(swjdp, instr, reg_addr,
+ RnW, outvalue, NULL, NULL);
+ if (retval != ERROR_OK)
+ return retval;
/* For reads, collect posted value; RDBUFF has no other effect.
* Assumes read gets acked with OK/FAULT, and CTRL_STAT says "OK".
*/
if ((RnW == DPAP_READ) && (invalue != NULL))
- adi_jtag_dp_scan_u32(swjdp, JTAG_DP_DPACC,
+ retval = adi_jtag_dp_scan_u32(swjdp, JTAG_DP_DPACC,
DP_RDBUFF, DPAP_READ, 0, invalue, &swjdp->ack);
-
- /* In TRANS_MODE_ATOMIC all JTAG_DP_APACC transactions wait for
- * ack = OK/FAULT and then check CTRL_STAT
- */
- if ((instr == JTAG_DP_APACC)
- && (swjdp->trans_mode == TRANS_MODE_ATOMIC))
- return jtagdp_transaction_endcheck(swjdp);
-
- return ERROR_OK;
+ return retval;
}
-int jtagdp_transaction_endcheck(struct swjdp_common *swjdp)
+static int jtagdp_transaction_endcheck(struct adiv5_dap *swjdp)
{
int retval;
uint32_t ctrlstat;
#if 0
/* Danger!!!! BROKEN!!!! */
- scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
+ adi_jtag_scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
DP_CTRL_STAT, DPAP_READ, 0, &ctrlstat);
/* Danger!!!! BROKEN!!!! Why will jtag_execute_queue() fail here????
R956 introduced the check on return value here and now Michael Schwingen reports
/* Post CTRL/STAT read; discard any previous posted read value
* but collect its ACK status.
*/
- scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
+ adi_jtag_scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
DP_CTRL_STAT, DPAP_READ, 0, &ctrlstat);
if ((retval = jtag_execute_queue()) != ERROR_OK)
return retval;
return ERROR_JTAG_DEVICE_ERROR;
}
- scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
+ adi_jtag_scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
DP_CTRL_STAT, DPAP_READ, 0, &ctrlstat);
- if ((retval = jtag_execute_queue()) != ERROR_OK)
+ if ((retval = dap_run(swjdp)) != ERROR_OK)
return retval;
swjdp->ack = swjdp->ack & 0x7;
}
LOG_ERROR("JTAG-DP STICKY ERROR");
/* Clear Sticky Error Bits */
- scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
+ adi_jtag_scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
DP_CTRL_STAT, DPAP_WRITE,
swjdp->dp_ctrl_stat | SSTICKYORUN
| SSTICKYERR, NULL);
- scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
+ adi_jtag_scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
DP_CTRL_STAT, DPAP_READ, 0, &ctrlstat);
- if ((retval = jtag_execute_queue()) != ERROR_OK)
+ if ((retval = dap_run(swjdp)) != ERROR_OK)
return retval;
LOG_DEBUG("jtag-dp: CTRL/STAT 0x%" PRIx32, ctrlstat);
- dap_ap_read_reg_u32(swjdp, AP_REG_CSW, &mem_ap_csw);
- dap_ap_read_reg_u32(swjdp, AP_REG_TAR, &mem_ap_tar);
- if ((retval = jtag_execute_queue()) != ERROR_OK)
+ retval = dap_queue_ap_read(swjdp,
+ AP_REG_CSW, &mem_ap_csw);
+ if (retval != ERROR_OK)
+ return retval;
+
+ retval = dap_queue_ap_read(swjdp,
+ AP_REG_TAR, &mem_ap_tar);
+ if (retval != ERROR_OK)
+ return retval;
+
+ if ((retval = dap_run(swjdp)) != ERROR_OK)
return retval;
LOG_ERROR("MEM_AP_CSW 0x%" PRIx32 ", MEM_AP_TAR 0x%"
PRIx32, mem_ap_csw, mem_ap_tar);
}
- if ((retval = jtag_execute_queue()) != ERROR_OK)
+ if ((retval = dap_run(swjdp)) != ERROR_OK)
return retval;
return ERROR_JTAG_DEVICE_ERROR;
}
* *
***************************************************************************/
-static int dap_dp_write_reg(struct swjdp_common *swjdp,
- uint32_t value, uint8_t reg_addr)
-{
- return scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
- reg_addr, DPAP_WRITE, value, NULL);
-}
-
-static int dap_dp_read_reg(struct swjdp_common *swjdp,
- uint32_t *value, uint8_t reg_addr)
-{
- return scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
- reg_addr, DPAP_READ, 0, value);
-}
-
/**
* Select one of the APs connected to the specified DAP. The
* selection is implicitly used with future AP transactions.
* @param apsel Number of the AP to (implicitly) use with further
* transactions. This normally identifies a MEM-AP.
*/
-void dap_ap_select(struct swjdp_common *swjdp,uint8_t apsel)
+void dap_ap_select(struct adiv5_dap *swjdp,uint8_t apsel)
{
uint32_t select = (apsel << 24) & 0xFF000000;
}
}
-/** Select the AP register bank matching bits 7:4 of ap_reg. */
-static int dap_ap_bankselect(struct swjdp_common *swjdp, uint32_t ap_reg)
-{
- uint32_t select = (ap_reg & 0x000000F0);
-
- if (select != swjdp->ap_bank_value)
- {
- swjdp->ap_bank_value = select;
- select |= swjdp->apsel;
- return dap_dp_write_reg(swjdp, select, DP_SELECT);
- } else
- return ERROR_OK;
-}
-
-static int dap_ap_write_reg(struct swjdp_common *swjdp,
- uint32_t reg_addr, uint8_t *out_value_buf)
-{
- int retval;
-
- retval = dap_ap_bankselect(swjdp, reg_addr);
- if (retval != ERROR_OK)
- return retval;
-
- return ap_write_check(swjdp, reg_addr, out_value_buf);
-}
-
/**
- * Write an AP register value.
- * This is synchronous iff the mode is set to ATOMIC, in which
- * case any queued transactions are flushed.
- *
- * @param swjdp The DAP whose currently selected AP will be written.
- * @param reg_addr Eight bit AP register address.
- * @param value Word to be written at reg_addr
- *
- * @return In synchronous mode: ERROR_OK for success, and the register holds
- * the specified value; else a fault code. In asynchronous mode, a status
- * code reflecting whether the transaction was properly queued.
- */
-int dap_ap_write_reg_u32(struct swjdp_common *swjdp,
- uint32_t reg_addr, uint32_t value)
-{
- uint8_t out_value_buf[4];
-
- buf_set_u32(out_value_buf, 0, 32, value);
- return dap_ap_write_reg(swjdp,
- reg_addr, out_value_buf);
-}
-
-/**
- * Read an AP register value.
- * This is synchronous iff the mode is set to ATOMIC, in which
- * case any queued transactions are flushed.
- *
- * @param swjdp The DAP whose currently selected AP will be read.
- * @param reg_addr Eight bit AP register address.
- * @param value Points to where the 32-bit (little-endian) word will be stored.
- *
- * @return In synchronous mode: ERROR_OK for success, and *value holds
- * the specified value; else a fault code. In asynchronous mode, a status
- * code reflecting whether the transaction was properly queued.
- */
-int dap_ap_read_reg_u32(struct swjdp_common *swjdp,
- uint32_t reg_addr, uint32_t *value)
-{
- int retval;
-
- retval = dap_ap_bankselect(swjdp, reg_addr);
- if (retval != ERROR_OK)
- return retval;
-
- return scan_inout_check_u32(swjdp, JTAG_DP_APACC, reg_addr,
- DPAP_READ, 0, value);
-}
-
-/**
- * Set up transfer parameters for the currently selected MEM-AP.
- * This is synchronous iff the mode is set to ATOMIC, in which
- * case any queued transactions are flushed.
+ * Queue transactions setting up transfer parameters for the
+ * currently selected MEM-AP.
*
* Subsequent transfers using registers like AP_REG_DRW or AP_REG_BD2
* initiate data reads or writes using memory or peripheral addresses.
* @param tar MEM-AP Transfer Address Register (TAR) to assign. If this
* matches the cached address, the register is not changed.
*
- * @return In synchronous mode: ERROR_OK for success, and the AP is set
- * up as requested else a fault code. In asynchronous mode, a status
- * code reflecting whether the transaction was properly queued.
+ * @return ERROR_OK if the transaction was properly queued, else a fault code.
*/
-int dap_setup_accessport(struct swjdp_common *swjdp, uint32_t csw, uint32_t tar)
+int dap_setup_accessport(struct adiv5_dap *swjdp, uint32_t csw, uint32_t tar)
{
int retval;
if (csw != swjdp->ap_csw_value)
{
/* LOG_DEBUG("DAP: Set CSW %x",csw); */
- retval = dap_ap_write_reg_u32(swjdp, AP_REG_CSW, csw);
+ retval = dap_queue_ap_write(swjdp, AP_REG_CSW, csw);
if (retval != ERROR_OK)
return retval;
swjdp->ap_csw_value = csw;
if (tar != swjdp->ap_tar_value)
{
/* LOG_DEBUG("DAP: Set TAR %x",tar); */
- retval = dap_ap_write_reg_u32(swjdp, AP_REG_TAR, tar);
+ retval = dap_queue_ap_write(swjdp, AP_REG_TAR, tar);
if (retval != ERROR_OK)
return retval;
swjdp->ap_tar_value = tar;
*
* @return ERROR_OK for success. Otherwise a fault code.
*/
-int mem_ap_read_u32(struct swjdp_common *swjdp, uint32_t address,
+int mem_ap_read_u32(struct adiv5_dap *swjdp, uint32_t address,
uint32_t *value)
{
int retval;
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
/* Use banked addressing (REG_BDx) to avoid some link traffic
* (updating TAR) when reading several consecutive addresses.
*/
if (retval != ERROR_OK)
return retval;
- return dap_ap_read_reg_u32(swjdp, AP_REG_BD0 | (address & 0xC), value);
+ return dap_queue_ap_read(swjdp, AP_REG_BD0 | (address & 0xC), value);
}
/**
* @return ERROR_OK for success; *value holds the result.
* Otherwise a fault code.
*/
-int mem_ap_read_atomic_u32(struct swjdp_common *swjdp, uint32_t address,
+int mem_ap_read_atomic_u32(struct adiv5_dap *swjdp, uint32_t address,
uint32_t *value)
{
int retval;
if (retval != ERROR_OK)
return retval;
- return jtagdp_transaction_endcheck(swjdp);
+ return dap_run(swjdp);
}
/**
*
* @return ERROR_OK for success. Otherwise a fault code.
*/
-int mem_ap_write_u32(struct swjdp_common *swjdp, uint32_t address,
+int mem_ap_write_u32(struct adiv5_dap *swjdp, uint32_t address,
uint32_t value)
{
int retval;
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
/* Use banked addressing (REG_BDx) to avoid some link traffic
* (updating TAR) when writing several consecutive addresses.
*/
if (retval != ERROR_OK)
return retval;
- return dap_ap_write_reg_u32(swjdp, AP_REG_BD0 | (address & 0xC),
+ return dap_queue_ap_write(swjdp, AP_REG_BD0 | (address & 0xC),
value);
}
*
* @return ERROR_OK for success; the data was written. Otherwise a fault code.
*/
-int mem_ap_write_atomic_u32(struct swjdp_common *swjdp, uint32_t address,
+int mem_ap_write_atomic_u32(struct adiv5_dap *swjdp, uint32_t address,
uint32_t value)
{
int retval = mem_ap_write_u32(swjdp, address, value);
if (retval != ERROR_OK)
return retval;
- return jtagdp_transaction_endcheck(swjdp);
+ return dap_run(swjdp);
}
/*****************************************************************************
* *
-* mem_ap_write_buf(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address) *
+* mem_ap_write_buf(struct adiv5_dap *swjdp, uint8_t *buffer, int count, uint32_t address) *
* *
* Write a buffer in target order (little endian) *
* *
*****************************************************************************/
-int mem_ap_write_buf_u32(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address)
+int mem_ap_write_buf_u32(struct adiv5_dap *swjdp, uint8_t *buffer, int count, uint32_t address)
{
int wcount, blocksize, writecount, errorcount = 0, retval = ERROR_OK;
uint32_t adr = address;
uint8_t* pBuffer = buffer;
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
count >>= 2;
wcount = count;
for (writecount = 0; writecount < blocksize; writecount++)
{
- dap_ap_write_reg(swjdp, AP_REG_DRW, buffer + 4 * writecount);
+ retval = dap_queue_ap_write(swjdp, AP_REG_DRW,
+ *(uint32_t *) (buffer + 4 * writecount));
+ if (retval != ERROR_OK)
+ break;
}
- if (jtagdp_transaction_endcheck(swjdp) == ERROR_OK)
+ if (dap_run(swjdp) == ERROR_OK)
{
wcount = wcount - blocksize;
address = address + 4 * blocksize;
if (errorcount > 1)
{
LOG_WARNING("Block write error address 0x%" PRIx32 ", wcount 0x%x", address, wcount);
+ /* REVISIT return the *actual* fault code */
return ERROR_JTAG_DEVICE_ERROR;
}
}
return retval;
}
-static int mem_ap_write_buf_packed_u16(struct swjdp_common *swjdp,
+static int mem_ap_write_buf_packed_u16(struct adiv5_dap *swjdp,
uint8_t *buffer, int count, uint32_t address)
{
int retval = ERROR_OK;
int wcount, blocksize, writecount, i;
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
wcount = count >> 1;
while (wcount > 0)
}
memcpy(&outvalue, buffer, sizeof(uint32_t));
- dap_ap_write_reg_u32(swjdp, AP_REG_DRW, outvalue);
- if (jtagdp_transaction_endcheck(swjdp) != ERROR_OK)
+ retval = dap_queue_ap_write(swjdp,
+ AP_REG_DRW, outvalue);
+ if (retval != ERROR_OK)
+ break;
+
+ if (dap_run(swjdp) != ERROR_OK)
{
LOG_WARNING("Block write error address "
"0x%" PRIx32 ", count 0x%x",
address, count);
+ /* REVISIT return *actual* fault code */
return ERROR_JTAG_DEVICE_ERROR;
}
}
return retval;
}
-int mem_ap_write_buf_u16(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address)
+int mem_ap_write_buf_u16(struct adiv5_dap *swjdp, uint8_t *buffer, int count, uint32_t address)
{
int retval = ERROR_OK;
if (count >= 4)
return mem_ap_write_buf_packed_u16(swjdp, buffer, count, address);
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
while (count > 0)
{
dap_setup_accessport(swjdp, CSW_16BIT | CSW_ADDRINC_SINGLE, address);
uint16_t svalue;
memcpy(&svalue, buffer, sizeof(uint16_t));
uint32_t outvalue = (uint32_t)svalue << 8 * (address & 0x3);
- dap_ap_write_reg_u32(swjdp, AP_REG_DRW, outvalue);
- retval = jtagdp_transaction_endcheck(swjdp);
+ retval = dap_queue_ap_write(swjdp, AP_REG_DRW, outvalue);
+ if (retval != ERROR_OK)
+ break;
+
+ retval = dap_run(swjdp);
+ if (retval != ERROR_OK)
+ break;
+
count -= 2;
address += 2;
buffer += 2;
return retval;
}
-static int mem_ap_write_buf_packed_u8(struct swjdp_common *swjdp,
+static int mem_ap_write_buf_packed_u8(struct adiv5_dap *swjdp,
uint8_t *buffer, int count, uint32_t address)
{
int retval = ERROR_OK;
int wcount, blocksize, writecount, i;
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
wcount = count;
while (wcount > 0)
}
memcpy(&outvalue, buffer, sizeof(uint32_t));
- dap_ap_write_reg_u32(swjdp, AP_REG_DRW, outvalue);
- if (jtagdp_transaction_endcheck(swjdp) != ERROR_OK)
+ retval = dap_queue_ap_write(swjdp,
+ AP_REG_DRW, outvalue);
+ if (retval != ERROR_OK)
+ break;
+
+ if (dap_run(swjdp) != ERROR_OK)
{
LOG_WARNING("Block write error address "
"0x%" PRIx32 ", count 0x%x",
address, count);
+ /* REVISIT return *actual* fault code */
return ERROR_JTAG_DEVICE_ERROR;
}
}
return retval;
}
-int mem_ap_write_buf_u8(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address)
+int mem_ap_write_buf_u8(struct adiv5_dap *swjdp, uint8_t *buffer, int count, uint32_t address)
{
int retval = ERROR_OK;
if (count >= 4)
return mem_ap_write_buf_packed_u8(swjdp, buffer, count, address);
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
while (count > 0)
{
dap_setup_accessport(swjdp, CSW_8BIT | CSW_ADDRINC_SINGLE, address);
uint32_t outvalue = (uint32_t)*buffer << 8 * (address & 0x3);
- dap_ap_write_reg_u32(swjdp, AP_REG_DRW, outvalue);
- retval = jtagdp_transaction_endcheck(swjdp);
+ retval = dap_queue_ap_write(swjdp, AP_REG_DRW, outvalue);
+ if (retval != ERROR_OK)
+ break;
+
+ retval = dap_run(swjdp);
+ if (retval != ERROR_OK)
+ break;
+
count--;
address++;
buffer++;
return retval;
}
-/*********************************************************************************
-* *
-* mem_ap_read_buf_u32(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address) *
-* *
-* Read block fast in target order (little endian) into a buffer *
-* *
-**********************************************************************************/
-int mem_ap_read_buf_u32(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address)
+/**
+ * Synchronously read a block of 32-bit words into a buffer
+ * @param swjdp The DAP connected to the MEM-AP.
+ * @param buffer where the words will be stored (in host byte order).
+ * @param count How many words to read.
+ * @param address Memory address from which to read words; all the
+ * words must be readable by the currently selected MEM-AP.
+ */
+int mem_ap_read_buf_u32(struct adiv5_dap *swjdp, uint8_t *buffer,
+ int count, uint32_t address)
{
int wcount, blocksize, readcount, errorcount = 0, retval = ERROR_OK;
uint32_t adr = address;
uint8_t* pBuffer = buffer;
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
count >>= 2;
wcount = count;
while (wcount > 0)
{
- /* Adjust to read blocks within boundaries aligned to the TAR autoincremnent size*/
- blocksize = max_tar_block_size(swjdp->tar_autoincr_block, address);
+ /* Adjust to read blocks within boundaries aligned to the
+ * TAR autoincrement size (at least 2^10). Autoincrement
+ * mode avoids an extra per-word roundtrip to update TAR.
+ */
+ blocksize = max_tar_block_size(swjdp->tar_autoincr_block,
+ address);
if (wcount < blocksize)
blocksize = wcount;
if (blocksize == 0)
blocksize = 1;
- dap_setup_accessport(swjdp, CSW_32BIT | CSW_ADDRINC_SINGLE, address);
+ dap_setup_accessport(swjdp, CSW_32BIT | CSW_ADDRINC_SINGLE,
+ address);
+
+ /* FIXME remove these three calls to adi_jtag_dp_scan(),
+ * so this routine becomes transport-neutral. Be careful
+ * not to cause performance problems with JTAG; would it
+ * suffice to loop over dap_queue_ap_read(), or would that
+ * be slower when JTAG is the chosen transport?
+ */
/* Scan out first read */
adi_jtag_dp_scan(swjdp, JTAG_DP_APACC, AP_REG_DRW,
adi_jtag_dp_scan(swjdp, JTAG_DP_DPACC, DP_RDBUFF,
DPAP_READ, 0, buffer + 4 * readcount,
&swjdp->ack);
- if (jtagdp_transaction_endcheck(swjdp) == ERROR_OK)
+ if (dap_run(swjdp) == ERROR_OK)
{
wcount = wcount - blocksize;
address += 4 * blocksize;
if (errorcount > 1)
{
- LOG_WARNING("Block read error address 0x%" PRIx32 ", count 0x%x", address, count);
+ LOG_WARNING("Block read error address 0x%" PRIx32
+ ", count 0x%x", address, count);
+ /* REVISIT return the *actual* fault code */
return ERROR_JTAG_DEVICE_ERROR;
}
}
for (i = 0; i < 4; i++)
{
- *((uint8_t*)pBuffer) = (data >> 8 * (adr & 0x3));
+ *((uint8_t*)pBuffer) =
+ (data >> 8 * (adr & 0x3));
pBuffer++;
adr++;
}
return retval;
}
-static int mem_ap_read_buf_packed_u16(struct swjdp_common *swjdp,
+static int mem_ap_read_buf_packed_u16(struct adiv5_dap *swjdp,
uint8_t *buffer, int count, uint32_t address)
{
uint32_t invalue;
int retval = ERROR_OK;
int wcount, blocksize, readcount, i;
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
wcount = count >> 1;
while (wcount > 0)
do
{
- dap_ap_read_reg_u32(swjdp, AP_REG_DRW, &invalue);
- if (jtagdp_transaction_endcheck(swjdp) != ERROR_OK)
+ retval = dap_queue_ap_read(swjdp, AP_REG_DRW, &invalue);
+ if (dap_run(swjdp) != ERROR_OK)
{
LOG_WARNING("Block read error address 0x%" PRIx32 ", count 0x%x", address, count);
+ /* REVISIT return the *actual* fault code */
return ERROR_JTAG_DEVICE_ERROR;
}
return retval;
}
-int mem_ap_read_buf_u16(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address)
+/**
+ * Synchronously read a block of 16-bit halfwords into a buffer
+ * @param swjdp The DAP connected to the MEM-AP.
+ * @param buffer where the halfwords will be stored (in host byte order).
+ * @param count How many halfwords to read.
+ * @param address Memory address from which to read words; all the
+ * words must be readable by the currently selected MEM-AP.
+ */
+int mem_ap_read_buf_u16(struct adiv5_dap *swjdp, uint8_t *buffer,
+ int count, uint32_t address)
{
uint32_t invalue, i;
int retval = ERROR_OK;
if (count >= 4)
return mem_ap_read_buf_packed_u16(swjdp, buffer, count, address);
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
while (count > 0)
{
dap_setup_accessport(swjdp, CSW_16BIT | CSW_ADDRINC_SINGLE, address);
- dap_ap_read_reg_u32(swjdp, AP_REG_DRW, &invalue);
- retval = jtagdp_transaction_endcheck(swjdp);
+ retval = dap_queue_ap_read(swjdp, AP_REG_DRW, &invalue);
+ if (retval != ERROR_OK)
+ break;
+
+ retval = dap_run(swjdp);
+ if (retval != ERROR_OK)
+ break;
+
if (address & 0x1)
{
for (i = 0; i < 2; i++)
* The solution is to arrange for a large out/in scan in this loop and
* and convert data afterwards.
*/
-static int mem_ap_read_buf_packed_u8(struct swjdp_common *swjdp,
+static int mem_ap_read_buf_packed_u8(struct adiv5_dap *swjdp,
uint8_t *buffer, int count, uint32_t address)
{
uint32_t invalue;
int retval = ERROR_OK;
int wcount, blocksize, readcount, i;
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
wcount = count;
while (wcount > 0)
do
{
- dap_ap_read_reg_u32(swjdp, AP_REG_DRW, &invalue);
- if (jtagdp_transaction_endcheck(swjdp) != ERROR_OK)
+ retval = dap_queue_ap_read(swjdp, AP_REG_DRW, &invalue);
+ if (dap_run(swjdp) != ERROR_OK)
{
LOG_WARNING("Block read error address 0x%" PRIx32 ", count 0x%x", address, count);
+ /* REVISIT return the *actual* fault code */
return ERROR_JTAG_DEVICE_ERROR;
}
return retval;
}
-int mem_ap_read_buf_u8(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address)
+/**
+ * Synchronously read a block of bytes into a buffer
+ * @param swjdp The DAP connected to the MEM-AP.
+ * @param buffer where the bytes will be stored.
+ * @param count How many bytes to read.
+ * @param address Memory address from which to read data; all the
+ * data must be readable by the currently selected MEM-AP.
+ */
+int mem_ap_read_buf_u8(struct adiv5_dap *swjdp, uint8_t *buffer,
+ int count, uint32_t address)
{
uint32_t invalue;
int retval = ERROR_OK;
if (count >= 4)
return mem_ap_read_buf_packed_u8(swjdp, buffer, count, address);
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
while (count > 0)
{
dap_setup_accessport(swjdp, CSW_8BIT | CSW_ADDRINC_SINGLE, address);
- dap_ap_read_reg_u32(swjdp, AP_REG_DRW, &invalue);
- retval = jtagdp_transaction_endcheck(swjdp);
+ retval = dap_queue_ap_read(swjdp, AP_REG_DRW, &invalue);
+ retval = dap_run(swjdp);
+ if (retval != ERROR_OK)
+ break;
+
*((uint8_t*)buffer) = (invalue >> 8 * (address & 0x3));
count--;
address++;
return retval;
}
+/*--------------------------------------------------------------------------*/
+
+static int jtag_idcode_q_read(struct adiv5_dap *dap,
+ uint8_t *ack, uint32_t *data)
+{
+ struct arm_jtag *jtag_info = dap->jtag_info;
+ int retval;
+ struct scan_field fields[1];
+
+ jtag_set_end_state(TAP_IDLE);
+
+ /* This is a standard JTAG operation -- no DAP tweakage */
+ retval = arm_jtag_set_instr(jtag_info, JTAG_DP_IDCODE, NULL);
+ if (retval != ERROR_OK)
+ return retval;
+
+ fields[0].num_bits = 32;
+ fields[0].out_value = NULL;
+ fields[0].in_value = (void *) data;
+
+ jtag_add_dr_scan(jtag_info->tap, 1, fields, jtag_get_end_state());
+ retval = jtag_get_error();
+ if (retval != ERROR_OK)
+ return retval;
+
+ jtag_add_callback(arm_le_to_h_u32,
+ (jtag_callback_data_t) data);
+
+ return retval;
+}
+
+static int jtag_dp_q_read(struct adiv5_dap *dap, unsigned reg,
+ uint32_t *data)
+{
+ return adi_jtag_scan_inout_check_u32(dap, JTAG_DP_DPACC,
+ reg, DPAP_READ, 0, data);
+}
+
+static int jtag_dp_q_write(struct adiv5_dap *dap, unsigned reg,
+ uint32_t data)
+{
+ return adi_jtag_scan_inout_check_u32(dap, JTAG_DP_DPACC,
+ reg, DPAP_WRITE, data, NULL);
+}
+
+/** Select the AP register bank matching bits 7:4 of reg. */
+static int jtag_ap_q_bankselect(struct adiv5_dap *dap, unsigned reg)
+{
+ uint32_t select = reg & 0x000000F0;
+
+ if (select == dap->ap_bank_value)
+ return ERROR_OK;
+ dap->ap_bank_value = select;
+
+ select |= dap->apsel;
+
+ return jtag_dp_q_write(dap, DP_SELECT, select);
+}
+
+static int jtag_ap_q_read(struct adiv5_dap *dap, unsigned reg,
+ uint32_t *data)
+{
+ int retval = jtag_ap_q_bankselect(dap, reg);
+
+ if (retval != ERROR_OK)
+ return retval;
+
+ return adi_jtag_scan_inout_check_u32(dap, JTAG_DP_APACC, reg,
+ DPAP_READ, 0, data);
+}
+
+static int jtag_ap_q_write(struct adiv5_dap *dap, unsigned reg,
+ uint32_t data)
+{
+ uint8_t out_value_buf[4];
+
+ int retval = jtag_ap_q_bankselect(dap, reg);
+ if (retval != ERROR_OK)
+ return retval;
+
+ buf_set_u32(out_value_buf, 0, 32, data);
+
+ return adi_jtag_ap_write_check(dap, reg, out_value_buf);
+}
+
+static int jtag_ap_q_abort(struct adiv5_dap *dap, uint8_t *ack)
+{
+ /* for JTAG, this is the only valid ABORT register operation */
+ return adi_jtag_dp_scan_u32(dap, JTAG_DP_ABORT,
+ 0, DPAP_WRITE, 1, NULL, ack);
+}
+
+static int jtag_dp_run(struct adiv5_dap *dap)
+{
+ return jtagdp_transaction_endcheck(dap);
+}
+
+static const struct dap_ops jtag_dp_ops = {
+ .queue_idcode_read = jtag_idcode_q_read,
+ .queue_dp_read = jtag_dp_q_read,
+ .queue_dp_write = jtag_dp_q_write,
+ .queue_ap_read = jtag_ap_q_read,
+ .queue_ap_write = jtag_ap_q_write,
+ .queue_ap_abort = jtag_ap_q_abort,
+ .run = jtag_dp_run,
+};
+
+/*--------------------------------------------------------------------------*/
+
/**
* Initialize a DAP. This sets up the power domains, prepares the DP
* for further use, and arranges to use AP #0 for all AP operations
* in layering. (JTAG is useful without any debug target; but not SWD.)
* And this may not even use an AHB-AP ... e.g. DAP-Lite uses an APB-AP.
*/
-int ahbap_debugport_init(struct swjdp_common *swjdp)
+int ahbap_debugport_init(struct adiv5_dap *swjdp)
{
uint32_t idreg, romaddr, dummy;
uint32_t ctrlstat;
LOG_DEBUG(" ");
+ /* JTAG-DP or SWJ-DP, in JTAG mode */
+ swjdp->ops = &jtag_dp_ops;
+
/* Default MEM-AP setup.
*
* REVISIT AP #0 may be an inappropriate default for this.
dap_ap_select(swjdp, 0);
/* DP initialization */
- swjdp->trans_mode = TRANS_MODE_ATOMIC;
- dap_dp_read_reg(swjdp, &dummy, DP_CTRL_STAT);
- dap_dp_write_reg(swjdp, SSTICKYERR, DP_CTRL_STAT);
- dap_dp_read_reg(swjdp, &dummy, DP_CTRL_STAT);
+
+ retval = dap_queue_dp_read(swjdp, DP_CTRL_STAT, &dummy);
+ if (retval != ERROR_OK)
+ return retval;
+
+ retval = dap_queue_dp_write(swjdp, DP_CTRL_STAT, SSTICKYERR);
+ if (retval != ERROR_OK)
+ return retval;
+
+ retval = dap_queue_dp_read(swjdp, DP_CTRL_STAT, &dummy);
+ if (retval != ERROR_OK)
+ return retval;
swjdp->dp_ctrl_stat = CDBGPWRUPREQ | CSYSPWRUPREQ;
+ retval = dap_queue_dp_write(swjdp, DP_CTRL_STAT, swjdp->dp_ctrl_stat);
+ if (retval != ERROR_OK)
+ return retval;
- dap_dp_write_reg(swjdp, swjdp->dp_ctrl_stat, DP_CTRL_STAT);
- dap_dp_read_reg(swjdp, &ctrlstat, DP_CTRL_STAT);
- if ((retval = jtag_execute_queue()) != ERROR_OK)
+ retval = dap_queue_dp_read(swjdp, DP_CTRL_STAT, &ctrlstat);
+ if (retval != ERROR_OK)
+ return retval;
+ if ((retval = dap_run(swjdp)) != ERROR_OK)
return retval;
/* Check that we have debug power domains activated */
while (!(ctrlstat & CDBGPWRUPACK) && (cnt++ < 10))
{
LOG_DEBUG("DAP: wait CDBGPWRUPACK");
- dap_dp_read_reg(swjdp, &ctrlstat, DP_CTRL_STAT);
- if ((retval = jtag_execute_queue()) != ERROR_OK)
+ retval = dap_queue_dp_read(swjdp, DP_CTRL_STAT, &ctrlstat);
+ if (retval != ERROR_OK)
+ return retval;
+ if ((retval = dap_run(swjdp)) != ERROR_OK)
return retval;
alive_sleep(10);
}
while (!(ctrlstat & CSYSPWRUPACK) && (cnt++ < 10))
{
LOG_DEBUG("DAP: wait CSYSPWRUPACK");
- dap_dp_read_reg(swjdp, &ctrlstat, DP_CTRL_STAT);
- if ((retval = jtag_execute_queue()) != ERROR_OK)
+ retval = dap_queue_dp_read(swjdp, DP_CTRL_STAT, &ctrlstat);
+ if (retval != ERROR_OK)
+ return retval;
+ if ((retval = dap_run(swjdp)) != ERROR_OK)
return retval;
alive_sleep(10);
}
- dap_dp_read_reg(swjdp, &dummy, DP_CTRL_STAT);
+ retval = dap_queue_dp_read(swjdp, DP_CTRL_STAT, &dummy);
+ if (retval != ERROR_OK)
+ return retval;
/* With debug power on we can activate OVERRUN checking */
swjdp->dp_ctrl_stat = CDBGPWRUPREQ | CSYSPWRUPREQ | CORUNDETECT;
- dap_dp_write_reg(swjdp, swjdp->dp_ctrl_stat, DP_CTRL_STAT);
- dap_dp_read_reg(swjdp, &dummy, DP_CTRL_STAT);
+ retval = dap_queue_dp_write(swjdp, DP_CTRL_STAT, swjdp->dp_ctrl_stat);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = dap_queue_dp_read(swjdp, DP_CTRL_STAT, &dummy);
+ if (retval != ERROR_OK)
+ return retval;
/*
* REVISIT this isn't actually *initializing* anything in an AP,
* Should it? If the ROM address is valid, is this the right
* place to scan the table and do any topology detection?
*/
- dap_ap_read_reg_u32(swjdp, AP_REG_IDR, &idreg);
- dap_ap_read_reg_u32(swjdp, AP_REG_BASE, &romaddr);
+ retval = dap_queue_ap_read(swjdp, AP_REG_IDR, &idreg);
+ retval = dap_queue_ap_read(swjdp, AP_REG_BASE, &romaddr);
LOG_DEBUG("MEM-AP #%d ID Register 0x%" PRIx32
", Debug ROM Address 0x%" PRIx32,
&& ((cid1 & 0x0f) == 0) && cid0 == 0x0d;
}
-int dap_info_command(struct command_context *cmd_ctx,
- struct swjdp_common *swjdp, int apsel)
+static int dap_info_command(struct command_context *cmd_ctx,
+ struct adiv5_dap *swjdp, int apsel)
{
-
+ int retval;
uint32_t dbgbase, apid;
int romtable_present = 0;
uint8_t mem_ap;
apselold = swjdp->apsel;
dap_ap_select(swjdp, apsel);
- dap_ap_read_reg_u32(swjdp, AP_REG_BASE, &dbgbase);
- dap_ap_read_reg_u32(swjdp, AP_REG_IDR, &apid);
- jtagdp_transaction_endcheck(swjdp);
+ retval = dap_queue_ap_read(swjdp, AP_REG_BASE, &dbgbase);
+ retval = dap_queue_ap_read(swjdp, AP_REG_IDR, &apid);
+ retval = dap_run(swjdp);
+ if (retval != ERROR_OK)
+ return retval;
+
/* Now we read ROM table ID registers, ref. ARM IHI 0029B sec */
mem_ap = ((apid&0x10000) && ((apid&0x0F) != 0));
command_print(cmd_ctx, "AP ID register 0x%8.8" PRIx32, apid);
mem_ap_read_u32(swjdp, (dbgbase&0xFFFFF000) | 0xFF8, &cid2);
mem_ap_read_u32(swjdp, (dbgbase&0xFFFFF000) | 0xFFC, &cid3);
mem_ap_read_u32(swjdp, (dbgbase&0xFFFFF000) | 0xFCC, &memtype);
- jtagdp_transaction_endcheck(swjdp);
+ retval = dap_run(swjdp);
+ if (retval != ERROR_OK)
+ return retval;
+
if (!is_dap_cid_ok(cid3, cid2, cid1, cid0))
command_print(cmd_ctx, "\tCID3 0x%2.2" PRIx32
", CID2 0x%2.2" PRIx32
type = "TI DAPCTL";
full = "";
break;
- case 0x4e0:
- type = "Cortex-M3 ETM";
- full = "(Embedded Trace)";
- break;
case 0x906:
type = "Coresight CTI";
full = "(Cross Trigger)";
type = "Cortex-M3 TPIU";
full = "(Trace Port Interface Unit)";
break;
+ case 0x924:
+ type = "Cortex-M3 ETM";
+ full = "(Embedded Trace)";
+ break;
case 0xc08:
type = "Cortex-A8 Debug";
full = "(Debug Unit)";
return ERROR_OK;
}
-DAP_COMMAND_HANDLER(dap_baseaddr_command)
+COMMAND_HANDLER(handle_dap_info_command)
+{
+ struct target *target = get_current_target(CMD_CTX);
+ struct arm *arm = target_to_arm(target);
+ struct adiv5_dap *dap = arm->dap;
+ uint32_t apsel;
+
+ switch (CMD_ARGC) {
+ case 0:
+ apsel = dap->apsel;
+ break;
+ case 1:
+ COMMAND_PARSE_NUMBER(u32, CMD_ARGV[0], apsel);
+ break;
+ default:
+ return ERROR_COMMAND_SYNTAX_ERROR;
+ }
+
+ return dap_info_command(CMD_CTX, dap, apsel);
+}
+
+COMMAND_HANDLER(dap_baseaddr_command)
{
+ struct target *target = get_current_target(CMD_CTX);
+ struct arm *arm = target_to_arm(target);
+ struct adiv5_dap *dap = arm->dap;
+
uint32_t apsel, apselsave, baseaddr;
int retval;
- apselsave = swjdp->apsel;
+ apselsave = dap->apsel;
switch (CMD_ARGC) {
case 0:
- apsel = swjdp->apsel;
+ apsel = dap->apsel;
break;
case 1:
COMMAND_PARSE_NUMBER(u32, CMD_ARGV[0], apsel);
}
if (apselsave != apsel)
- dap_ap_select(swjdp, apsel);
+ dap_ap_select(dap, apsel);
/* NOTE: assumes we're talking to a MEM-AP, which
* has a base address. There are other kinds of AP,
* though they're not common for now. This should
* use the ID register to verify it's a MEM-AP.
*/
- dap_ap_read_reg_u32(swjdp, AP_REG_BASE, &baseaddr);
- retval = jtagdp_transaction_endcheck(swjdp);
+ retval = dap_queue_ap_read(dap, AP_REG_BASE, &baseaddr);
+ retval = dap_run(dap);
+ if (retval != ERROR_OK)
+ return retval;
+
command_print(CMD_CTX, "0x%8.8" PRIx32, baseaddr);
if (apselsave != apsel)
- dap_ap_select(swjdp, apselsave);
+ dap_ap_select(dap, apselsave);
return retval;
}
-DAP_COMMAND_HANDLER(dap_memaccess_command)
+COMMAND_HANDLER(dap_memaccess_command)
{
+ struct target *target = get_current_target(CMD_CTX);
+ struct arm *arm = target_to_arm(target);
+ struct adiv5_dap *dap = arm->dap;
+
uint32_t memaccess_tck;
switch (CMD_ARGC) {
case 0:
- memaccess_tck = swjdp->memaccess_tck;
+ memaccess_tck = dap->memaccess_tck;
break;
case 1:
COMMAND_PARSE_NUMBER(u32, CMD_ARGV[0], memaccess_tck);
default:
return ERROR_COMMAND_SYNTAX_ERROR;
}
- swjdp->memaccess_tck = memaccess_tck;
+ dap->memaccess_tck = memaccess_tck;
command_print(CMD_CTX, "memory bus access delay set to %" PRIi32 " tck",
- swjdp->memaccess_tck);
+ dap->memaccess_tck);
return ERROR_OK;
}
-DAP_COMMAND_HANDLER(dap_apsel_command)
+COMMAND_HANDLER(dap_apsel_command)
{
+ struct target *target = get_current_target(CMD_CTX);
+ struct arm *arm = target_to_arm(target);
+ struct adiv5_dap *dap = arm->dap;
+
uint32_t apsel, apid;
int retval;
return ERROR_COMMAND_SYNTAX_ERROR;
}
- dap_ap_select(swjdp, apsel);
- dap_ap_read_reg_u32(swjdp, AP_REG_IDR, &apid);
- retval = jtagdp_transaction_endcheck(swjdp);
+ dap_ap_select(dap, apsel);
+ retval = dap_queue_ap_read(dap, AP_REG_IDR, &apid);
+ retval = dap_run(dap);
+ if (retval != ERROR_OK)
+ return retval;
+
command_print(CMD_CTX, "ap %" PRIi32 " selected, identification register 0x%8.8" PRIx32,
apsel, apid);
return retval;
}
-DAP_COMMAND_HANDLER(dap_apid_command)
+COMMAND_HANDLER(dap_apid_command)
{
+ struct target *target = get_current_target(CMD_CTX);
+ struct arm *arm = target_to_arm(target);
+ struct adiv5_dap *dap = arm->dap;
+
uint32_t apsel, apselsave, apid;
int retval;
- apselsave = swjdp->apsel;
+ apselsave = dap->apsel;
switch (CMD_ARGC) {
case 0:
- apsel = swjdp->apsel;
+ apsel = dap->apsel;
break;
case 1:
COMMAND_PARSE_NUMBER(u32, CMD_ARGV[0], apsel);
}
if (apselsave != apsel)
- dap_ap_select(swjdp, apsel);
+ dap_ap_select(dap, apsel);
+
+ retval = dap_queue_ap_read(dap, AP_REG_IDR, &apid);
+ retval = dap_run(dap);
+ if (retval != ERROR_OK)
+ return retval;
- dap_ap_read_reg_u32(swjdp, AP_REG_IDR, &apid);
- retval = jtagdp_transaction_endcheck(swjdp);
command_print(CMD_CTX, "0x%8.8" PRIx32, apid);
if (apselsave != apsel)
- dap_ap_select(swjdp, apselsave);
+ dap_ap_select(dap, apselsave);
+
+ return retval;
+}
+
+static const struct command_registration dap_commands[] = {
+ {
+ .name = "info",
+ .handler = handle_dap_info_command,
+ .mode = COMMAND_EXEC,
+ .help = "display ROM table for MEM-AP "
+ "(default currently selected AP)",
+ .usage = "[ap_num]",
+ },
+ {
+ .name = "apsel",
+ .handler = dap_apsel_command,
+ .mode = COMMAND_EXEC,
+ .help = "Set the currently selected AP (default 0) "
+ "and display the result",
+ .usage = "[ap_num]",
+ },
+ {
+ .name = "apid",
+ .handler = dap_apid_command,
+ .mode = COMMAND_EXEC,
+ .help = "return ID register from AP "
+ "(default currently selected AP)",
+ .usage = "[ap_num]",
+ },
+ {
+ .name = "baseaddr",
+ .handler = dap_baseaddr_command,
+ .mode = COMMAND_EXEC,
+ .help = "return debug base address from MEM-AP "
+ "(default currently selected AP)",
+ .usage = "[ap_num]",
+ },
+ {
+ .name = "memaccess",
+ .handler = dap_memaccess_command,
+ .mode = COMMAND_EXEC,
+ .help = "set/get number of extra tck for MEM-AP memory "
+ "bus access [0-255]",
+ .usage = "[cycles]",
+ },
+ COMMAND_REGISTRATION_DONE
+};
+
+const struct command_registration dap_command_handlers[] = {
+ {
+ .name = "dap",
+ .mode = COMMAND_EXEC,
+ .help = "DAP command group",
+ .chain = dap_commands,
+ },
+ COMMAND_REGISTRATION_DONE
+};
+
+
+/*
+ * This represents the bits which must be sent out on TMS/SWDIO to
+ * switch a DAP implemented using an SWJ-DP module into SWD mode.
+ * These bits are stored (and transmitted) LSB-first.
+ *
+ * See the DAP-Lite specification, section 2.2.5 for information
+ * about making the debug link select SWD or JTAG. (Similar info
+ * is in a few other ARM documents.)
+ */
+static const uint8_t jtag2swd_bitseq[] = {
+ /* More than 50 TCK/SWCLK cycles with TMS/SWDIO high,
+ * putting both JTAG and SWD logic into reset state.
+ */
+ 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
+ /* Switching sequence enables SWD and disables JTAG
+ * NOTE: bits in the DP's IDCODE may expose the need for
+ * an old/deprecated sequence (0xb6 0xed).
+ */
+ 0x9e, 0xe7,
+ /* More than 50 TCK/SWCLK cycles with TMS/SWDIO high,
+ * putting both JTAG and SWD logic into reset state.
+ */
+ 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
+};
+
+/**
+ * Put the debug link into SWD mode, if the target supports it.
+ * The link's initial mode may be either JTAG (for example,
+ * with SWJ-DP after reset) or SWD.
+ *
+ * @param target Enters SWD mode (if possible).
+ *
+ * Note that targets using the JTAG-DP do not support SWD, and that
+ * some targets which could otherwise support it may have have been
+ * configured to disable SWD signaling
+ *
+ * @return ERROR_OK or else a fault code.
+ */
+int dap_to_swd(struct target *target)
+{
+ int retval;
+
+ LOG_DEBUG("Enter SWD mode");
+
+ /* REVISIT it's nasty to need to make calls to a "jtag"
+ * subsystem if the link isn't in JTAG mode...
+ */
+
+ retval = jtag_add_tms_seq(8 * sizeof(jtag2swd_bitseq),
+ jtag2swd_bitseq, TAP_INVALID);
+ if (retval == ERROR_OK)
+ retval = jtag_execute_queue();
+
+ /* REVISIT set up the DAP's ops vector for SWD mode. */
+
+ return retval;
+}
+
+/**
+ * This represents the bits which must be sent out on TMS/SWDIO to
+ * switch a DAP implemented using an SWJ-DP module into JTAG mode.
+ * These bits are stored (and transmitted) LSB-first.
+ *
+ * These bits are stored (and transmitted) LSB-first.
+ */
+static const uint8_t swd2jtag_bitseq[] = {
+ /* More than 50 TCK/SWCLK cycles with TMS/SWDIO high,
+ * putting both JTAG and SWD logic into reset state.
+ */
+ 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
+ /* Switching equence disables SWD and enables JTAG
+ * NOTE: bits in the DP's IDCODE can expose the need for
+ * the old/deprecated sequence (0xae 0xde).
+ */
+ 0x3c, 0xe7,
+ /* At least 50 TCK/SWCLK cycles with TMS/SWDIO high,
+ * putting both JTAG and SWD logic into reset state.
+ * NOTE: some docs say "at least 5".
+ */
+ 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
+};
+
+/** Put the debug link into JTAG mode, if the target supports it.
+ * The link's initial mode may be either SWD or JTAG.
+ *
+ * @param target Enters JTAG mode (if possible).
+ *
+ * Note that targets implemented with SW-DP do not support JTAG, and
+ * that some targets which could otherwise support it may have been
+ * configured to disable JTAG signaling
+ *
+ * @return ERROR_OK or else a fault code.
+ */
+int dap_to_jtag(struct target *target)
+{
+ int retval;
+
+ LOG_DEBUG("Enter JTAG mode");
+
+ /* REVISIT it's nasty to need to make calls to a "jtag"
+ * subsystem if the link isn't in JTAG mode...
+ */
+
+ retval = jtag_add_tms_seq(8 * sizeof(swd2jtag_bitseq),
+ swd2jtag_bitseq, TAP_RESET);
+ if (retval == ERROR_OK)
+ retval = jtag_execute_queue();
+
+ /* REVISIT set up the DAP's ops vector for JTAG mode. */
return retval;
}
projects / openocd / blobdiff