* *
* Copyright (C) 2009 by Oyvind Harboe *
* oyvind.harboe@zylin.com *
- * *
+ * *
+ * Copyright (C) 2009-2010 by David Brownell *
+ * *
* This program is free software; you can redistribute it and/or modify *
* it under the terms of the GNU General Public License as published by *
* the Free Software Foundation; either version 2 of the License, or *
* Free Software Foundation, Inc., *
* 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. *
***************************************************************************/
-/***************************************************************************
- * *
- * This file implements support for the ARM Debug Interface v5 (ADI_V5) *
- * *
- * ARM(tm) Debug Interface v5 Architecture Specification ARM IHI 0031A *
- * *
- * CoreSight(tm) DAP-Lite TRM, ARM DDI 0316D *
- * Cortex-M3(tm) TRM, ARM DDI 0337G *
- * *
-***************************************************************************/
+
+/**
+ * @file
+ * This file implements support for the ARM Debug Interface version 5 (ADIv5)
+ * debugging architecture. Compared with previous versions, this includes
+ * a low pin-count Serial Wire Debug (SWD) alternative to JTAG for message
+ * transport, and focusses on memory mapped resources as defined by the
+ * CoreSight architecture.
+ *
+ * A key concept in ADIv5 is the Debug Access Port, or DAP. A DAP has two
+ * basic components: a Debug Port (DP) transporting messages to and from a
+ * debugger, and an Access Port (AP) accessing resources. Three types of DP
+ * are defined. One uses only JTAG for communication, and is called JTAG-DP.
+ * One uses only SWD for communication, and is called SW-DP. The third can
+ * use either SWD or JTAG, and is called SWJ-DP. The most common type of AP
+ * is used to access memory mapped resources and is called a MEM-AP. Also a
+ * JTAG-AP is also defined, bridging to JTAG resources; those are uncommon.
+ *
+ * @todo Remove modality (queued/nonqueued, via DAP trans_mode) from all
+ * procedure interfaces. Modal programming interfaces are very error prone.
+ * Procedures should be either queued, or synchronous. Otherwise input
+ * and output constraints are context-sensitive, and it's hard to know
+ * what a block of code will do just by reading it.
+ */
+
+/*
+ * Relevant specifications from ARM include:
+ *
+ * ARM(tm) Debug Interface v5 Architecture Specification ARM IHI 0031A
+ * CoreSight(tm) v1.0 Architecture Specification ARM IHI 0029B
+ *
+ * CoreSight(tm) DAP-Lite TRM, ARM DDI 0316D
+ * Cortex-M3(tm) TRM, ARM DDI 0337G
+ */
#ifdef HAVE_CONFIG_H
#include "config.h"
#endif
#include "arm_adi_v5.h"
-#include "time_support.h"
+#include <helper/time_support.h>
/*
* Transaction Mode:
* *
***************************************************************************/
-/* Scan out and in from target ordered uint8_t buffers */
-int adi_jtag_dp_scan(struct swjdp_common *swjdp, uint8_t instr, uint8_t reg_addr, uint8_t RnW, uint8_t *outvalue, uint8_t *invalue, uint8_t *ack)
+/**
+ * Scan DPACC or APACC using target ordered uint8_t buffers. No endianness
+ * conversions are performed. See section 4.4.3 of the ADIv5 spec, which
+ * discusses operations which access these registers.
+ *
+ * Note that only one scan is performed. If RnW is set, a separate scan
+ * will be needed to collect the data which was read; the "invalue" collects
+ * the posted result of a preceding operation, not the current one.
+ *
+ * @param swjdp the DAP
+ * @param instr JTAG_DP_APACC (AP access) or JTAG_DP_DPACC (DP access)
+ * @param reg_addr two significant bits; A[3:2]; for APACC access, the
+ * SELECT register has more addressing bits.
+ * @param RnW false iff outvalue will be written to the DP or AP
+ * @param outvalue points to a 32-bit (little-endian) integer
+ * @param invalue NULL, or points to a 32-bit (little-endian) integer
+ * @param ack points to where the three bit JTAG_ACK_* code will be stored
+ */
+static int adi_jtag_dp_scan(struct swjdp_common *swjdp,
+ uint8_t instr, uint8_t reg_addr, uint8_t RnW,
+ uint8_t *outvalue, uint8_t *invalue, uint8_t *ack)
{
struct arm_jtag *jtag_info = swjdp->jtag_info;
struct scan_field fields[2];
arm_jtag_set_instr(jtag_info, instr, NULL);
/* Add specified number of tck clocks before accessing memory bus */
- if ((instr == DAP_IR_APACC) && ((reg_addr == AP_REG_DRW)||((reg_addr&0xF0) == AP_REG_BD0))&& (swjdp->memaccess_tck != 0))
+
+ /* REVISIT these TCK cycles should be *AFTER* updating APACC, since
+ * they provide more time for the (MEM) AP to complete the read ...
+ * See "Minimum Response Time" for JTAG-DP, in the ADIv5 spec.
+ */
+ if ((instr == JTAG_DP_APACC)
+ && ((reg_addr == AP_REG_DRW)
+ || ((reg_addr & 0xF0) == AP_REG_BD0))
+ && (swjdp->memaccess_tck != 0))
jtag_add_runtest(swjdp->memaccess_tck, jtag_set_end_state(TAP_IDLE));
+ /* Scan out a read or write operation using some DP or AP register.
+ * For APACC access with any sticky error flag set, this is discarded.
+ */
fields[0].tap = jtag_info->tap;
fields[0].num_bits = 3;
buf_set_u32(&out_addr_buf, 0, 3, ((reg_addr >> 1) & 0x6) | (RnW & 0x1));
fields[0].out_value = &out_addr_buf;
fields[0].in_value = ack;
+ /* NOTE: if we receive JTAG_ACK_WAIT, the previous operation did not
+ * complete; data we write is discarded, data we read is unpredictable.
+ * When overrun detect is active, STICKYORUN is set.
+ */
+
fields[1].tap = jtag_info->tap;
fields[1].num_bits = 32;
fields[1].out_value = outvalue;
}
/* Scan out and in from host ordered uint32_t variables */
-int adi_jtag_dp_scan_u32(struct swjdp_common *swjdp, uint8_t instr, uint8_t reg_addr, uint8_t RnW, uint32_t outvalue, uint32_t *invalue, uint8_t *ack)
+static int adi_jtag_dp_scan_u32(struct swjdp_common *swjdp,
+ uint8_t instr, uint8_t reg_addr, uint8_t RnW,
+ uint32_t outvalue, uint32_t *invalue, uint8_t *ack)
{
struct arm_jtag *jtag_info = swjdp->jtag_info;
struct scan_field fields[2];
arm_jtag_set_instr(jtag_info, instr, NULL);
/* Add specified number of tck clocks before accessing memory bus */
- if ((instr == DAP_IR_APACC) && ((reg_addr == AP_REG_DRW)||((reg_addr&0xF0) == AP_REG_BD0))&& (swjdp->memaccess_tck != 0))
+
+ /* REVISIT these TCK cycles should be *AFTER* updating APACC, since
+ * they provide more time for the (MEM) AP to complete the read ...
+ */
+ if ((instr == JTAG_DP_APACC)
+ && ((reg_addr == AP_REG_DRW)
+ || ((reg_addr & 0xF0) == AP_REG_BD0))
+ && (swjdp->memaccess_tck != 0))
jtag_add_runtest(swjdp->memaccess_tck, jtag_set_end_state(TAP_IDLE));
fields[0].tap = jtag_info->tap;
}
/* scan_inout_check adds one extra inscan for DPAP_READ commands to read variables */
-int scan_inout_check(struct swjdp_common *swjdp, uint8_t instr, uint8_t reg_addr, uint8_t RnW, uint8_t *outvalue, uint8_t *invalue)
+static int scan_inout_check(struct swjdp_common *swjdp,
+ uint8_t instr, uint8_t reg_addr, uint8_t RnW,
+ uint8_t *outvalue, uint8_t *invalue)
{
adi_jtag_dp_scan(swjdp, instr, reg_addr, RnW, outvalue, NULL, NULL);
if ((RnW == DPAP_READ) && (invalue != NULL))
- {
- adi_jtag_dp_scan(swjdp, DAP_IR_DPACC, DP_RDBUFF, DPAP_READ, 0, invalue, &swjdp->ack);
- }
+ adi_jtag_dp_scan(swjdp, JTAG_DP_DPACC,
+ DP_RDBUFF, DPAP_READ, 0, invalue, &swjdp->ack);
- /* In TRANS_MODE_ATOMIC all DAP_IR_APACC transactions wait for ack = OK/FAULT and the check CTRL_STAT */
- if ((instr == DAP_IR_APACC) && (swjdp->trans_mode == TRANS_MODE_ATOMIC))
- {
- return swjdp_transaction_endcheck(swjdp);
- }
+ /* In TRANS_MODE_ATOMIC all JTAG_DP_APACC transactions wait for
+ * ack = OK/FAULT and the check CTRL_STAT
+ */
+ if ((instr == JTAG_DP_APACC)
+ && (swjdp->trans_mode == TRANS_MODE_ATOMIC))
+ return jtagdp_transaction_endcheck(swjdp);
return ERROR_OK;
}
-int scan_inout_check_u32(struct swjdp_common *swjdp, uint8_t instr, uint8_t reg_addr, uint8_t RnW, uint32_t outvalue, uint32_t *invalue)
+static int scan_inout_check_u32(struct swjdp_common *swjdp,
+ uint8_t instr, uint8_t reg_addr, uint8_t RnW,
+ uint32_t outvalue, uint32_t *invalue)
{
+ /* Issue the read or write */
adi_jtag_dp_scan_u32(swjdp, instr, reg_addr, RnW, outvalue, NULL, NULL);
+ /* For reads, collect posted value; RDBUFF has no other effect.
+ * Assumes read gets acked with OK/FAULT, and CTRL_STAT says "OK".
+ */
if ((RnW == DPAP_READ) && (invalue != NULL))
- {
- adi_jtag_dp_scan_u32(swjdp, DAP_IR_DPACC, DP_RDBUFF, DPAP_READ, 0, invalue, &swjdp->ack);
- }
+ adi_jtag_dp_scan_u32(swjdp, JTAG_DP_DPACC,
+ DP_RDBUFF, DPAP_READ, 0, invalue, &swjdp->ack);
- /* In TRANS_MODE_ATOMIC all DAP_IR_APACC transactions wait for ack = OK/FAULT and then check CTRL_STAT */
- if ((instr == DAP_IR_APACC) && (swjdp->trans_mode == TRANS_MODE_ATOMIC))
- {
- return swjdp_transaction_endcheck(swjdp);
- }
+ /* In TRANS_MODE_ATOMIC all JTAG_DP_APACC transactions wait for
+ * ack = OK/FAULT and then check CTRL_STAT
+ */
+ if ((instr == JTAG_DP_APACC)
+ && (swjdp->trans_mode == TRANS_MODE_ATOMIC))
+ return jtagdp_transaction_endcheck(swjdp);
return ERROR_OK;
}
-int swjdp_transaction_endcheck(struct swjdp_common *swjdp)
+int jtagdp_transaction_endcheck(struct swjdp_common *swjdp)
{
int retval;
uint32_t ctrlstat;
#if 0
/* Danger!!!! BROKEN!!!! */
- scan_inout_check_u32(swjdp, DAP_IR_DPACC, DP_CTRL_STAT, DPAP_READ, 0, &ctrlstat);
+ scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
+ DP_CTRL_STAT, DPAP_READ, 0, &ctrlstat);
/* Danger!!!! BROKEN!!!! Why will jtag_execute_queue() fail here????
R956 introduced the check on return value here and now Michael Schwingen reports
that this code no longer works....
/* Why??? second time it works??? */
#endif
- scan_inout_check_u32(swjdp, DAP_IR_DPACC, DP_CTRL_STAT, DPAP_READ, 0, &ctrlstat);
+ /* Post CTRL/STAT read; discard any previous posted read value
+ * but collect its ACK status.
+ */
+ scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
+ DP_CTRL_STAT, DPAP_READ, 0, &ctrlstat);
if ((retval = jtag_execute_queue()) != ERROR_OK)
return retval;
swjdp->ack = swjdp->ack & 0x7;
- if (swjdp->ack != 2)
+ /* common code path avoids calling timeval_ms() */
+ if (swjdp->ack != JTAG_ACK_OK_FAULT)
{
long long then = timeval_ms();
- while (swjdp->ack != 2)
+
+ while (swjdp->ack != JTAG_ACK_OK_FAULT)
{
- if (swjdp->ack == 1)
+ if (swjdp->ack == JTAG_ACK_WAIT)
{
if ((timeval_ms()-then) > 1000)
{
- LOG_WARNING("Timeout (1000ms) waiting for ACK = OK/FAULT in SWJDP transaction");
+ /* NOTE: this would be a good spot
+ * to use JTAG_DP_ABORT.
+ */
+ LOG_WARNING("Timeout (1000ms) waiting "
+ "for ACK=OK/FAULT "
+ "in JTAG-DP transaction");
return ERROR_JTAG_DEVICE_ERROR;
}
}
else
{
- LOG_WARNING("Invalid ACK in SWJDP transaction");
+ LOG_WARNING("Invalid ACK %#x "
+ "in JTAG-DP transaction",
+ swjdp->ack);
return ERROR_JTAG_DEVICE_ERROR;
}
- scan_inout_check_u32(swjdp, DAP_IR_DPACC, DP_CTRL_STAT, DPAP_READ, 0, &ctrlstat);
+ scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
+ DP_CTRL_STAT, DPAP_READ, 0, &ctrlstat);
if ((retval = jtag_execute_queue()) != ERROR_OK)
return retval;
swjdp->ack = swjdp->ack & 0x7;
}
- } else
- {
- /* common code path avoids fn to timeval_ms() */
}
+ /* REVISIT also STICKYCMP, for pushed comparisons (nyet used) */
+
/* Check for STICKYERR and STICKYORUN */
if (ctrlstat & (SSTICKYORUN | SSTICKYERR))
{
- LOG_DEBUG("swjdp: CTRL/STAT error 0x%" PRIx32 "", ctrlstat);
+ LOG_DEBUG("jtag-dp: CTRL/STAT error, 0x%" PRIx32, ctrlstat);
/* Check power to debug regions */
if ((ctrlstat & 0xf0000000) != 0xf0000000)
- {
ahbap_debugport_init(swjdp);
- }
else
{
uint32_t mem_ap_csw, mem_ap_tar;
- /* Print information about last AHBAP access */
- LOG_ERROR("AHBAP Cached values: dp_select 0x%" PRIx32 ", ap_csw 0x%" PRIx32 ", ap_tar 0x%" PRIx32 "", swjdp->dp_select_value, swjdp->ap_csw_value, swjdp->ap_tar_value);
+ /* Maybe print information about last intended
+ * MEM-AP access; but not if autoincrementing.
+ * *Real* CSW and TAR values are always shown.
+ */
+ if (swjdp->ap_tar_value != (uint32_t) -1)
+ LOG_DEBUG("MEM-AP Cached values: "
+ "ap_bank 0x%" PRIx32
+ ", ap_csw 0x%" PRIx32
+ ", ap_tar 0x%" PRIx32,
+ swjdp->dp_select_value,
+ swjdp->ap_csw_value,
+ swjdp->ap_tar_value);
+
if (ctrlstat & SSTICKYORUN)
- LOG_ERROR("SWJ-DP OVERRUN - check clock or reduce jtag speed");
+ LOG_ERROR("JTAG-DP OVERRUN - check clock, "
+ "memaccess, or reduce jtag speed");
if (ctrlstat & SSTICKYERR)
- LOG_ERROR("SWJ-DP STICKY ERROR");
+ LOG_ERROR("JTAG-DP STICKY ERROR");
/* Clear Sticky Error Bits */
- scan_inout_check_u32(swjdp, DAP_IR_DPACC, DP_CTRL_STAT, DPAP_WRITE, swjdp->dp_ctrl_stat | SSTICKYORUN | SSTICKYERR, NULL);
- scan_inout_check_u32(swjdp, DAP_IR_DPACC, DP_CTRL_STAT, DPAP_READ, 0, &ctrlstat);
+ scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
+ DP_CTRL_STAT, DPAP_WRITE,
+ swjdp->dp_ctrl_stat | SSTICKYORUN
+ | SSTICKYERR, NULL);
+ scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
+ DP_CTRL_STAT, DPAP_READ, 0, &ctrlstat);
if ((retval = jtag_execute_queue()) != ERROR_OK)
return retval;
- LOG_DEBUG("swjdp: status 0x%" PRIx32 "", ctrlstat);
+ LOG_DEBUG("jtag-dp: CTRL/STAT 0x%" PRIx32, ctrlstat);
dap_ap_read_reg_u32(swjdp, AP_REG_CSW, &mem_ap_csw);
dap_ap_read_reg_u32(swjdp, AP_REG_TAR, &mem_ap_tar);
if ((retval = jtag_execute_queue()) != ERROR_OK)
return retval;
- LOG_ERROR("Read MEM_AP_CSW 0x%" PRIx32 ", MEM_AP_TAR 0x%" PRIx32 "", mem_ap_csw, mem_ap_tar);
+ LOG_ERROR("MEM_AP_CSW 0x%" PRIx32 ", MEM_AP_TAR 0x%"
+ PRIx32, mem_ap_csw, mem_ap_tar);
}
if ((retval = jtag_execute_queue()) != ERROR_OK)
* *
***************************************************************************/
-int dap_dp_write_reg(struct swjdp_common *swjdp, uint32_t value, uint8_t reg_addr)
+static int dap_dp_write_reg(struct swjdp_common *swjdp,
+ uint32_t value, uint8_t reg_addr)
{
- return scan_inout_check_u32(swjdp, DAP_IR_DPACC, reg_addr, DPAP_WRITE, value, NULL);
+ return scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
+ reg_addr, DPAP_WRITE, value, NULL);
}
-int dap_dp_read_reg(struct swjdp_common *swjdp, uint32_t *value, uint8_t reg_addr)
+static int dap_dp_read_reg(struct swjdp_common *swjdp,
+ uint32_t *value, uint8_t reg_addr)
{
- return scan_inout_check_u32(swjdp, DAP_IR_DPACC, reg_addr, DPAP_READ, 0, value);
+ return scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
+ reg_addr, DPAP_READ, 0, value);
}
-int dap_ap_select(struct swjdp_common *swjdp,uint8_t apsel)
+/**
+ * Select one of the APs connected to the specified DAP. The
+ * selection is implicitly used with future AP transactions.
+ * This is a NOP if the specified AP is already selected.
+ *
+ * @param swjdp The DAP
+ * @param apsel Number of the AP to (implicitly) use with further
+ * transactions. This normally identifies a MEM-AP.
+ */
+void dap_ap_select(struct swjdp_common *swjdp,uint8_t apsel)
{
uint32_t select;
select = (apsel << 24) & 0xFF000000;
swjdp->ap_csw_value = -1;
swjdp->ap_tar_value = -1;
}
-
- return ERROR_OK;
}
-int dap_dp_bankselect(struct swjdp_common *swjdp,uint32_t ap_reg)
+static int dap_dp_bankselect(struct swjdp_common *swjdp, uint32_t ap_reg)
{
uint32_t select;
select = (ap_reg & 0x000000F0);
swjdp->dp_select_value = select;
}
+ /* FIXME return any fault code from write() call */
return ERROR_OK;
}
-int dap_ap_write_reg(struct swjdp_common *swjdp, uint32_t reg_addr, uint8_t* out_value_buf)
+static int dap_ap_write_reg(struct swjdp_common *swjdp,
+ uint32_t reg_addr, uint8_t *out_value_buf)
{
dap_dp_bankselect(swjdp, reg_addr);
- scan_inout_check(swjdp, DAP_IR_APACC, reg_addr, DPAP_WRITE, out_value_buf, NULL);
+ scan_inout_check(swjdp, JTAG_DP_APACC, reg_addr,
+ DPAP_WRITE, out_value_buf, NULL);
+ /* FIXME return fault code from above calls */
return ERROR_OK;
}
-int dap_ap_read_reg(struct swjdp_common *swjdp, uint32_t reg_addr, uint8_t *in_value_buf)
-{
- dap_dp_bankselect(swjdp, reg_addr);
- scan_inout_check(swjdp, DAP_IR_APACC, reg_addr, DPAP_READ, 0, in_value_buf);
-
- return ERROR_OK;
-}
-int dap_ap_write_reg_u32(struct swjdp_common *swjdp, uint32_t reg_addr, uint32_t value)
+/**
+ * Write an AP register value.
+ * This is synchronous iff the mode is set to ATOMIC, in which
+ * case any queued transactions are flushed.
+ *
+ * @param swjdp The DAP whose currently selected AP will be written.
+ * @param reg_addr Eight bit AP register address.
+ * @param value Word to be written at reg_addr
+ *
+ * @return In synchronous mode: ERROR_OK for success, and the register holds
+ * the specified value; else a fault code. In asynchronous mode, a status
+ * code reflecting whether the transaction was properly queued.
+ */
+int dap_ap_write_reg_u32(struct swjdp_common *swjdp,
+ uint32_t reg_addr, uint32_t value)
{
uint8_t out_value_buf[4];
buf_set_u32(out_value_buf, 0, 32, value);
dap_dp_bankselect(swjdp, reg_addr);
- scan_inout_check(swjdp, DAP_IR_APACC, reg_addr, DPAP_WRITE, out_value_buf, NULL);
+ scan_inout_check(swjdp, JTAG_DP_APACC, reg_addr,
+ DPAP_WRITE, out_value_buf, NULL);
+ /* FIXME return any fault code from above calls */
return ERROR_OK;
}
-int dap_ap_read_reg_u32(struct swjdp_common *swjdp, uint32_t reg_addr, uint32_t *value)
+/**
+ * Read an AP register value.
+ * This is synchronous iff the mode is set to ATOMIC, in which
+ * case any queued transactions are flushed.
+ *
+ * @param swjdp The DAP whose currently selected AP will be read.
+ * @param reg_addr Eight bit AP register address.
+ * @param value Points to where the 32-bit (little-endian) word will be stored.
+ *
+ * @return In synchronous mode: ERROR_OK for success, and *value holds
+ * the specified value; else a fault code. In asynchronous mode, a status
+ * code reflecting whether the transaction was properly queued.
+ */
+int dap_ap_read_reg_u32(struct swjdp_common *swjdp,
+ uint32_t reg_addr, uint32_t *value)
{
dap_dp_bankselect(swjdp, reg_addr);
- scan_inout_check_u32(swjdp, DAP_IR_APACC, reg_addr, DPAP_READ, 0, value);
+ scan_inout_check_u32(swjdp, JTAG_DP_APACC, reg_addr,
+ DPAP_READ, 0, value);
+ /* FIXME return any fault code from above calls */
return ERROR_OK;
}
-/***************************************************************************
- * *
- * AHB-AP access to memory and system registers on AHB bus *
- * *
-***************************************************************************/
-
+/**
+ * Set up transfer parameters for the currently selected MEM-AP.
+ * This is synchronous iff the mode is set to ATOMIC, in which
+ * case any queued transactions are flushed.
+ *
+ * Subsequent transfers using registers like AP_REG_DRW or AP_REG_BD2
+ * initiate data reads or writes using memory or peripheral addresses.
+ * If the CSW is configured for it, the TAR may be automatically
+ * incremented after each transfer.
+ *
+ * @todo Rename to reflect it being specifically a MEM-AP function.
+ *
+ * @param swjdp The DAP connected to the MEM-AP.
+ * @param csw MEM-AP Control/Status Word (CSW) register to assign. If this
+ * matches the cached value, the register is not changed.
+ * @param tar MEM-AP Transfer Address Register (TAR) to assign. If this
+ * matches the cached address, the register is not changed.
+ *
+ * @return In synchronous mode: ERROR_OK for success, and the AP is set
+ * up as requested else a fault code. In asynchronous mode, a status
+ * code reflecting whether the transaction was properly queued.
+ */
int dap_setup_accessport(struct swjdp_common *swjdp, uint32_t csw, uint32_t tar)
{
csw = csw | CSW_DBGSWENABLE | CSW_MASTER_DEBUG | CSW_HPROT;
if (csw != swjdp->ap_csw_value)
{
- /* LOG_DEBUG("swjdp : Set CSW %x",csw); */
+ /* LOG_DEBUG("DAP: Set CSW %x",csw); */
+ /* FIXME if this call fails, fail this procedure! */
dap_ap_write_reg_u32(swjdp, AP_REG_CSW, csw);
swjdp->ap_csw_value = csw;
}
if (tar != swjdp->ap_tar_value)
{
- /* LOG_DEBUG("swjdp : Set TAR %x",tar); */
+ /* LOG_DEBUG("DAP: Set TAR %x",tar); */
+ /* FIXME if this call fails, fail this procedure! */
dap_ap_write_reg_u32(swjdp, AP_REG_TAR, tar);
swjdp->ap_tar_value = tar;
}
+ /* Disable TAR cache when autoincrementing */
if (csw & CSW_ADDRINC_MASK)
- {
- /* Do not cache TAR value when autoincrementing */
swjdp->ap_tar_value = -1;
- }
return ERROR_OK;
}
-/*****************************************************************************
-* *
-* mem_ap_read_u32(struct swjdp_common *swjdp, uint32_t address, uint32_t *value) *
-* *
-* Read a uint32_t value from memory or system register *
-* Functionally equivalent to target_read_u32(target, address, uint32_t *value), *
-* but with less overhead *
-*****************************************************************************/
-int mem_ap_read_u32(struct swjdp_common *swjdp, uint32_t address, uint32_t *value)
+/**
+ * Asynchronous (queued) read of a word from memory or a system register.
+ *
+ * @param swjdp The DAP connected to the MEM-AP performing the read.
+ * @param address Address of the 32-bit word to read; it must be
+ * readable by the currently selected MEM-AP.
+ * @param value points to where the word will be stored when the
+ * transaction queue is flushed (assuming no errors).
+ *
+ * @return ERROR_OK for success. Otherwise a fault code.
+ */
+int mem_ap_read_u32(struct swjdp_common *swjdp, uint32_t address,
+ uint32_t *value)
{
swjdp->trans_mode = TRANS_MODE_COMPOSITE;
- dap_setup_accessport(swjdp, CSW_32BIT | CSW_ADDRINC_OFF, address & 0xFFFFFFF0);
+ /* Use banked addressing (REG_BDx) to avoid some link traffic
+ * (updating TAR) when reading several consecutive addresses.
+ */
+ dap_setup_accessport(swjdp, CSW_32BIT | CSW_ADDRINC_OFF,
+ address & 0xFFFFFFF0);
dap_ap_read_reg_u32(swjdp, AP_REG_BD0 | (address & 0xC), value);
+ /* FIXME return any fault code from above calls */
return ERROR_OK;
}
-int mem_ap_read_atomic_u32(struct swjdp_common *swjdp, uint32_t address, uint32_t *value)
+/**
+ * Synchronous read of a word from memory or a system register.
+ * As a side effect, this flushes any queued transactions.
+ *
+ * @param swjdp The DAP connected to the MEM-AP performing the read.
+ * @param address Address of the 32-bit word to read; it must be
+ * readable by the currently selected MEM-AP.
+ * @param value points to where the result will be stored.
+ *
+ * @return ERROR_OK for success; *value holds the result.
+ * Otherwise a fault code.
+ */
+int mem_ap_read_atomic_u32(struct swjdp_common *swjdp, uint32_t address,
+ uint32_t *value)
{
mem_ap_read_u32(swjdp, address, value);
+ /* FIXME return any fault code from above call */
- return swjdp_transaction_endcheck(swjdp);
+ return jtagdp_transaction_endcheck(swjdp);
}
-/*****************************************************************************
-* *
-* mem_ap_write_u32(struct swjdp_common *swjdp, uint32_t address, uint32_t value) *
-* *
-* Write a uint32_t value to memory or memory mapped register *
-* *
-*****************************************************************************/
-int mem_ap_write_u32(struct swjdp_common *swjdp, uint32_t address, uint32_t value)
+/**
+ * Asynchronous (queued) write of a word to memory or a system register.
+ *
+ * @param swjdp The DAP connected to the MEM-AP.
+ * @param address Address to be written; it must be writable by
+ * the currently selected MEM-AP.
+ * @param value Word that will be written to the address when transaction
+ * queue is flushed (assuming no errors).
+ *
+ * @return ERROR_OK for success. Otherwise a fault code.
+ */
+int mem_ap_write_u32(struct swjdp_common *swjdp, uint32_t address,
+ uint32_t value)
{
swjdp->trans_mode = TRANS_MODE_COMPOSITE;
- dap_setup_accessport(swjdp, CSW_32BIT | CSW_ADDRINC_OFF, address & 0xFFFFFFF0);
+ /* Use banked addressing (REG_BDx) to avoid some link traffic
+ * (updating TAR) when writing several consecutive addresses.
+ */
+ dap_setup_accessport(swjdp, CSW_32BIT | CSW_ADDRINC_OFF,
+ address & 0xFFFFFFF0);
dap_ap_write_reg_u32(swjdp, AP_REG_BD0 | (address & 0xC), value);
+ /* FIXME return any fault code from above calls */
return ERROR_OK;
}
-int mem_ap_write_atomic_u32(struct swjdp_common *swjdp, uint32_t address, uint32_t value)
+/**
+ * Synchronous write of a word to memory or a system register.
+ * As a side effect, this flushes any queued transactions.
+ *
+ * @param swjdp The DAP connected to the MEM-AP.
+ * @param address Address to be written; it must be writable by
+ * the currently selected MEM-AP.
+ * @param value Word that will be written.
+ *
+ * @return ERROR_OK for success; the data was written. Otherwise a fault code.
+ */
+int mem_ap_write_atomic_u32(struct swjdp_common *swjdp, uint32_t address,
+ uint32_t value)
{
mem_ap_write_u32(swjdp, address, value);
+ /* FIXME return any fault code from above call */
- return swjdp_transaction_endcheck(swjdp);
+ return jtagdp_transaction_endcheck(swjdp);
}
/*****************************************************************************
dap_ap_write_reg(swjdp, AP_REG_DRW, buffer + 4 * writecount);
}
- if (swjdp_transaction_endcheck(swjdp) == ERROR_OK)
+ if (jtagdp_transaction_endcheck(swjdp) == ERROR_OK)
{
wcount = wcount - blocksize;
address = address + 4 * blocksize;
return retval;
}
-int mem_ap_write_buf_packed_u16(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address)
+static int mem_ap_write_buf_packed_u16(struct swjdp_common *swjdp,
+ uint8_t *buffer, int count, uint32_t address)
{
int retval = ERROR_OK;
int wcount, blocksize, writecount, i;
if (nbytes < 4)
{
- if (mem_ap_write_buf_u16(swjdp, buffer, nbytes, address) != ERROR_OK)
+ if (mem_ap_write_buf_u16(swjdp, buffer,
+ nbytes, address) != ERROR_OK)
{
- LOG_WARNING("Block read error address 0x%" PRIx32 ", count 0x%x", address, count);
+ LOG_WARNING("Block write error address "
+ "0x%" PRIx32 ", count 0x%x",
+ address, count);
return ERROR_JTAG_DEVICE_ERROR;
}
memcpy(&outvalue, buffer, sizeof(uint32_t));
dap_ap_write_reg_u32(swjdp, AP_REG_DRW, outvalue);
- if (swjdp_transaction_endcheck(swjdp) != ERROR_OK)
+ if (jtagdp_transaction_endcheck(swjdp) != ERROR_OK)
{
- LOG_WARNING("Block read error address 0x%" PRIx32 ", count 0x%x", address, count);
+ LOG_WARNING("Block write error address "
+ "0x%" PRIx32 ", count 0x%x",
+ address, count);
return ERROR_JTAG_DEVICE_ERROR;
}
}
memcpy(&svalue, buffer, sizeof(uint16_t));
uint32_t outvalue = (uint32_t)svalue << 8 * (address & 0x3);
dap_ap_write_reg_u32(swjdp, AP_REG_DRW, outvalue);
- retval = swjdp_transaction_endcheck(swjdp);
+ retval = jtagdp_transaction_endcheck(swjdp);
count -= 2;
address += 2;
buffer += 2;
return retval;
}
-int mem_ap_write_buf_packed_u8(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address)
+static int mem_ap_write_buf_packed_u8(struct swjdp_common *swjdp,
+ uint8_t *buffer, int count, uint32_t address)
{
int retval = ERROR_OK;
int wcount, blocksize, writecount, i;
{
if (mem_ap_write_buf_u8(swjdp, buffer, nbytes, address) != ERROR_OK)
{
- LOG_WARNING("Block read error address 0x%" PRIx32 ", count 0x%x", address, count);
+ LOG_WARNING("Block write error address "
+ "0x%" PRIx32 ", count 0x%x",
+ address, count);
return ERROR_JTAG_DEVICE_ERROR;
}
memcpy(&outvalue, buffer, sizeof(uint32_t));
dap_ap_write_reg_u32(swjdp, AP_REG_DRW, outvalue);
- if (swjdp_transaction_endcheck(swjdp) != ERROR_OK)
+ if (jtagdp_transaction_endcheck(swjdp) != ERROR_OK)
{
- LOG_WARNING("Block read error address 0x%" PRIx32 ", count 0x%x", address, count);
+ LOG_WARNING("Block write error address "
+ "0x%" PRIx32 ", count 0x%x",
+ address, count);
return ERROR_JTAG_DEVICE_ERROR;
}
}
dap_setup_accessport(swjdp, CSW_8BIT | CSW_ADDRINC_SINGLE, address);
uint32_t outvalue = (uint32_t)*buffer << 8 * (address & 0x3);
dap_ap_write_reg_u32(swjdp, AP_REG_DRW, outvalue);
- retval = swjdp_transaction_endcheck(swjdp);
+ retval = jtagdp_transaction_endcheck(swjdp);
count--;
address++;
buffer++;
dap_setup_accessport(swjdp, CSW_32BIT | CSW_ADDRINC_SINGLE, address);
/* Scan out first read */
- adi_jtag_dp_scan(swjdp, DAP_IR_APACC, AP_REG_DRW, DPAP_READ, 0, NULL, NULL);
+ adi_jtag_dp_scan(swjdp, JTAG_DP_APACC, AP_REG_DRW,
+ DPAP_READ, 0, NULL, NULL);
for (readcount = 0; readcount < blocksize - 1; readcount++)
{
- /* Scan out read instruction and scan in previous value */
- adi_jtag_dp_scan(swjdp, DAP_IR_APACC, AP_REG_DRW, DPAP_READ, 0, buffer + 4 * readcount, &swjdp->ack);
+ /* Scan out next read; scan in posted value for the
+ * previous one. Assumes read is acked "OK/FAULT",
+ * and CTRL_STAT says that meant "OK".
+ */
+ adi_jtag_dp_scan(swjdp, JTAG_DP_APACC, AP_REG_DRW,
+ DPAP_READ, 0, buffer + 4 * readcount,
+ &swjdp->ack);
}
- /* Scan in last value */
- adi_jtag_dp_scan(swjdp, DAP_IR_DPACC, DP_RDBUFF, DPAP_READ, 0, buffer + 4 * readcount, &swjdp->ack);
- if (swjdp_transaction_endcheck(swjdp) == ERROR_OK)
+ /* Scan in last posted value; RDBUFF has no other effect,
+ * assuming ack is OK/FAULT and CTRL_STAT says "OK".
+ */
+ adi_jtag_dp_scan(swjdp, JTAG_DP_DPACC, DP_RDBUFF,
+ DPAP_READ, 0, buffer + 4 * readcount,
+ &swjdp->ack);
+ if (jtagdp_transaction_endcheck(swjdp) == ERROR_OK)
{
wcount = wcount - blocksize;
address += 4 * blocksize;
return retval;
}
-int mem_ap_read_buf_packed_u16(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address)
+static int mem_ap_read_buf_packed_u16(struct swjdp_common *swjdp,
+ uint8_t *buffer, int count, uint32_t address)
{
uint32_t invalue;
int retval = ERROR_OK;
do
{
dap_ap_read_reg_u32(swjdp, AP_REG_DRW, &invalue);
- if (swjdp_transaction_endcheck(swjdp) != ERROR_OK)
+ if (jtagdp_transaction_endcheck(swjdp) != ERROR_OK)
{
LOG_WARNING("Block read error address 0x%" PRIx32 ", count 0x%x", address, count);
return ERROR_JTAG_DEVICE_ERROR;
{
dap_setup_accessport(swjdp, CSW_16BIT | CSW_ADDRINC_SINGLE, address);
dap_ap_read_reg_u32(swjdp, AP_REG_DRW, &invalue);
- retval = swjdp_transaction_endcheck(swjdp);
+ retval = jtagdp_transaction_endcheck(swjdp);
if (address & 0x1)
{
for (i = 0; i < 2; i++)
* The solution is to arrange for a large out/in scan in this loop and
* and convert data afterwards.
*/
-int mem_ap_read_buf_packed_u8(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address)
+static int mem_ap_read_buf_packed_u8(struct swjdp_common *swjdp,
+ uint8_t *buffer, int count, uint32_t address)
{
uint32_t invalue;
int retval = ERROR_OK;
do
{
dap_ap_read_reg_u32(swjdp, AP_REG_DRW, &invalue);
- if (swjdp_transaction_endcheck(swjdp) != ERROR_OK)
+ if (jtagdp_transaction_endcheck(swjdp) != ERROR_OK)
{
LOG_WARNING("Block read error address 0x%" PRIx32 ", count 0x%x", address, count);
return ERROR_JTAG_DEVICE_ERROR;
{
dap_setup_accessport(swjdp, CSW_8BIT | CSW_ADDRINC_SINGLE, address);
dap_ap_read_reg_u32(swjdp, AP_REG_DRW, &invalue);
- retval = swjdp_transaction_endcheck(swjdp);
+ retval = jtagdp_transaction_endcheck(swjdp);
*((uint8_t*)buffer) = (invalue >> 8 * (address & 0x3));
count--;
address++;
return retval;
}
+/**
+ * Initialize a DAP. This sets up the power domains, prepares the DP
+ * for further use, and arranges to use AP #0 for all AP operations
+ * until dap_ap-select() changes that policy.
+ *
+ * @param swjdp The DAP being initialized.
+ *
+ * @todo Rename this. We also need an initialization scheme which account
+ * for SWD transports not just JTAG; that will need to address differences
+ * in layering. (JTAG is useful without any debug target; but not SWD.)
+ * And this may not even use an AHB-AP ... e.g. DAP-Lite uses an APB-AP.
+ */
int ahbap_debugport_init(struct swjdp_common *swjdp)
{
uint32_t idreg, romaddr, dummy;
LOG_DEBUG(" ");
+ /* Default MEM-AP setup.
+ *
+ * REVISIT AP #0 may be an inappropriate default for this.
+ * Should we probe, or receve a hint from the caller?
+ * Presumably we can ignore the possibility of multiple APs.
+ */
swjdp->apsel = 0;
swjdp->ap_csw_value = -1;
swjdp->ap_tar_value = -1;
+
+ /* DP initialization */
swjdp->trans_mode = TRANS_MODE_ATOMIC;
dap_dp_read_reg(swjdp, &dummy, DP_CTRL_STAT);
dap_dp_write_reg(swjdp, SSTICKYERR, DP_CTRL_STAT);
/* Check that we have debug power domains activated */
while (!(ctrlstat & CDBGPWRUPACK) && (cnt++ < 10))
{
- LOG_DEBUG("swjdp: wait CDBGPWRUPACK");
+ LOG_DEBUG("DAP: wait CDBGPWRUPACK");
dap_dp_read_reg(swjdp, &ctrlstat, DP_CTRL_STAT);
if ((retval = jtag_execute_queue()) != ERROR_OK)
return retval;
while (!(ctrlstat & CSYSPWRUPACK) && (cnt++ < 10))
{
- LOG_DEBUG("swjdp: wait CSYSPWRUPACK");
+ LOG_DEBUG("DAP: wait CSYSPWRUPACK");
dap_dp_read_reg(swjdp, &ctrlstat, DP_CTRL_STAT);
if ((retval = jtag_execute_queue()) != ERROR_OK)
return retval;
dap_dp_write_reg(swjdp, swjdp->dp_ctrl_stat, DP_CTRL_STAT);
dap_dp_read_reg(swjdp, &dummy, DP_CTRL_STAT);
- dap_ap_read_reg_u32(swjdp, 0xFC, &idreg);
- dap_ap_read_reg_u32(swjdp, 0xF8, &romaddr);
+ /*
+ * REVISIT this isn't actually *initializing* anything in an AP,
+ * and doesn't care if it's a MEM-AP at all (much less AHB-AP).
+ * Should it? If the ROM address is valid, is this the right
+ * place to scan the table and do any topology detection?
+ */
+ dap_ap_read_reg_u32(swjdp, AP_REG_IDR, &idreg);
+ dap_ap_read_reg_u32(swjdp, AP_REG_BASE, &romaddr);
- LOG_DEBUG("AHB-AP ID Register 0x%" PRIx32 ", Debug ROM Address 0x%" PRIx32 "", idreg, romaddr);
+ LOG_DEBUG("MEM-AP #%d ID Register 0x%" PRIx32
+ ", Debug ROM Address 0x%" PRIx32,
+ swjdp->apsel, idreg, romaddr);
return ERROR_OK;
}
-/* CID interpretation -- see ARM IHI 0029B section 3 */
+/* CID interpretation -- see ARM IHI 0029B section 3
+ * and ARM IHI 0031A table 13-3.
+ */
static const char *class_description[16] ={
"Reserved", "ROM table", "Reserved", "Reserved",
"Reserved", "Reserved", "Reserved", "Reserved",
"Reserved", "CoreSight component", "Reserved", "Peripheral Test Block",
- "Reserved", "DESS", "Generic IP component", "PrimeCell or System component"
+ "Reserved", "OptimoDE DESS",
+ "Generic IP component", "PrimeCell or System component"
};
static bool
&& ((cid1 & 0x0f) == 0) && cid0 == 0x0d;
}
-int dap_info_command(struct command_context *cmd_ctx, struct swjdp_common *swjdp, int apsel)
+int dap_info_command(struct command_context *cmd_ctx,
+ struct swjdp_common *swjdp, int apsel)
{
- uint32_t dbgbase,apid;
+ uint32_t dbgbase, apid;
int romtable_present = 0;
uint8_t mem_ap;
uint32_t apselold;
+ /* AP address is in bits 31:24 of DP_SELECT */
+ if (apsel >= 256)
+ return ERROR_INVALID_ARGUMENTS;
+
apselold = swjdp->apsel;
dap_ap_select(swjdp, apsel);
- dap_ap_read_reg_u32(swjdp, 0xF8, &dbgbase);
- dap_ap_read_reg_u32(swjdp, 0xFC, &apid);
- swjdp_transaction_endcheck(swjdp);
+ dap_ap_read_reg_u32(swjdp, AP_REG_BASE, &dbgbase);
+ dap_ap_read_reg_u32(swjdp, AP_REG_IDR, &apid);
+ jtagdp_transaction_endcheck(swjdp);
/* Now we read ROM table ID registers, ref. ARM IHI 0029B sec */
mem_ap = ((apid&0x10000) && ((apid&0x0F) != 0));
- command_print(cmd_ctx, "ap identification register 0x%8.8" PRIx32 "", apid);
+ command_print(cmd_ctx, "AP ID register 0x%8.8" PRIx32, apid);
if (apid)
{
switch (apid&0x0F)
{
case 0:
- command_print(cmd_ctx, "\tType is jtag-ap");
+ command_print(cmd_ctx, "\tType is JTAG-AP");
break;
case 1:
- command_print(cmd_ctx, "\tType is mem-ap AHB");
+ command_print(cmd_ctx, "\tType is MEM-AP AHB");
break;
case 2:
- command_print(cmd_ctx, "\tType is mem-ap APB");
+ command_print(cmd_ctx, "\tType is MEM-AP APB");
break;
default:
- command_print(cmd_ctx, "\tUnknown AP-type");
- break;
+ command_print(cmd_ctx, "\tUnknown AP type");
+ break;
}
- command_print(cmd_ctx, "ap debugbase 0x%8.8" PRIx32 "", dbgbase);
+
+ /* NOTE: a MEM-AP may have a single CoreSight component that's
+ * not a ROM table ... or have no such components at all.
+ */
+ if (mem_ap)
+ command_print(cmd_ctx, "AP BASE 0x%8.8" PRIx32,
+ dbgbase);
}
else
{
mem_ap_read_u32(swjdp, (dbgbase&0xFFFFF000) | 0xFF8, &cid2);
mem_ap_read_u32(swjdp, (dbgbase&0xFFFFF000) | 0xFFC, &cid3);
mem_ap_read_u32(swjdp, (dbgbase&0xFFFFF000) | 0xFCC, &memtype);
- swjdp_transaction_endcheck(swjdp);
+ jtagdp_transaction_endcheck(swjdp);
if (!is_dap_cid_ok(cid3, cid2, cid1, cid0))
command_print(cmd_ctx, "\tCID3 0x%2.2" PRIx32
", CID2 0x%2.2" PRIx32
int retval;
apselsave = swjdp->apsel;
- switch (argc) {
+ switch (CMD_ARGC) {
case 0:
apsel = swjdp->apsel;
break;
case 1:
- COMMAND_PARSE_NUMBER(u32, args[0], apsel);
+ COMMAND_PARSE_NUMBER(u32, CMD_ARGV[0], apsel);
+ /* AP address is in bits 31:24 of DP_SELECT */
+ if (apsel >= 256)
+ return ERROR_INVALID_ARGUMENTS;
break;
default:
return ERROR_COMMAND_SYNTAX_ERROR;
if (apselsave != apsel)
dap_ap_select(swjdp, apsel);
- dap_ap_read_reg_u32(swjdp, 0xF8, &baseaddr);
- retval = swjdp_transaction_endcheck(swjdp);
- command_print(cmd_ctx, "0x%8.8" PRIx32, baseaddr);
+ /* NOTE: assumes we're talking to a MEM-AP, which
+ * has a base address. There are other kinds of AP,
+ * though they're not common for now. This should
+ * use the ID register to verify it's a MEM-AP.
+ */
+ dap_ap_read_reg_u32(swjdp, AP_REG_BASE, &baseaddr);
+ retval = jtagdp_transaction_endcheck(swjdp);
+ command_print(CMD_CTX, "0x%8.8" PRIx32, baseaddr);
if (apselsave != apsel)
dap_ap_select(swjdp, apselsave);
{
uint32_t memaccess_tck;
- switch (argc) {
+ switch (CMD_ARGC) {
case 0:
memaccess_tck = swjdp->memaccess_tck;
break;
case 1:
- COMMAND_PARSE_NUMBER(u32, args[0], memaccess_tck);
+ COMMAND_PARSE_NUMBER(u32, CMD_ARGV[0], memaccess_tck);
break;
default:
return ERROR_COMMAND_SYNTAX_ERROR;
}
swjdp->memaccess_tck = memaccess_tck;
- command_print(cmd_ctx, "memory bus access delay set to %" PRIi32 " tck",
+ command_print(CMD_CTX, "memory bus access delay set to %" PRIi32 " tck",
swjdp->memaccess_tck);
return ERROR_OK;
uint32_t apsel, apid;
int retval;
- switch (argc) {
+ switch (CMD_ARGC) {
case 0:
apsel = 0;
break;
case 1:
- COMMAND_PARSE_NUMBER(u32, args[0], apsel);
+ COMMAND_PARSE_NUMBER(u32, CMD_ARGV[0], apsel);
+ /* AP address is in bits 31:24 of DP_SELECT */
+ if (apsel >= 256)
+ return ERROR_INVALID_ARGUMENTS;
break;
default:
return ERROR_COMMAND_SYNTAX_ERROR;
}
dap_ap_select(swjdp, apsel);
- dap_ap_read_reg_u32(swjdp, 0xFC, &apid);
- retval = swjdp_transaction_endcheck(swjdp);
- command_print(cmd_ctx, "ap %" PRIi32 " selected, identification register 0x%8.8" PRIx32,
+ dap_ap_read_reg_u32(swjdp, AP_REG_IDR, &apid);
+ retval = jtagdp_transaction_endcheck(swjdp);
+ command_print(CMD_CTX, "ap %" PRIi32 " selected, identification register 0x%8.8" PRIx32,
apsel, apid);
return retval;
int retval;
apselsave = swjdp->apsel;
- switch (argc) {
+ switch (CMD_ARGC) {
case 0:
apsel = swjdp->apsel;
break;
case 1:
- COMMAND_PARSE_NUMBER(u32, args[0], apsel);
+ COMMAND_PARSE_NUMBER(u32, CMD_ARGV[0], apsel);
+ /* AP address is in bits 31:24 of DP_SELECT */
+ if (apsel >= 256)
+ return ERROR_INVALID_ARGUMENTS;
break;
default:
return ERROR_COMMAND_SYNTAX_ERROR;
if (apselsave != apsel)
dap_ap_select(swjdp, apsel);
- dap_ap_read_reg_u32(swjdp, 0xFC, &apid);
- retval = swjdp_transaction_endcheck(swjdp);
- command_print(cmd_ctx, "0x%8.8" PRIx32, apid);
+ dap_ap_read_reg_u32(swjdp, AP_REG_IDR, &apid);
+ retval = jtagdp_transaction_endcheck(swjdp);
+ command_print(CMD_CTX, "0x%8.8" PRIx32, apid);
if (apselsave != apsel)
dap_ap_select(swjdp, apselsave);