environment area within the total memory of your DataFlash placed
at the specified address.
+- CONFIG_ENV_IS_IN_REMOTE:
+
+ Define this if you have a remote memory space which you
+ want to use for the local device's environment.
+
+ - CONFIG_ENV_ADDR:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines specify the address and size of the
+ environment area within the remote memory space. The
+ local device can get the environment from remote memory
+ space by SRIO or other links.
+
+BE CAREFUL! For some special cases, the local device can not use
+"saveenv" command. For example, the local device will get the
+environment stored in a remote NOR flash by SRIO link, but it can
+not erase, write this NOR flash by SRIO interface.
+
- CONFIG_ENV_IS_IN_NAND:
Define this if you have a NAND device which you want to use
Specifies that QE/FMAN firmware is located on the primary SPI
device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
+- CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+ Specifies that QE/FMAN firmware is located in the remote (master)
+ memory space. CONFIG_SYS_FMAN_FW_ADDR is a virtual address which
+ can be mapped from slave TLB->slave LAW->slave SRIO outbound window
+ ->master inbound window->master LAW->the ucode address in master's
+ NOR flash.
Building the Software:
======================
#include <asm/mmu.h>
#include <asm/fsl_law.h>
#include <asm/fsl_serdes.h>
+#include <asm/fsl_srio.h>
#include <linux/compiler.h>
#include "mp.h"
#ifdef CONFIG_SYS_QE_FMAN_FW_IN_NAND
DECLARE_GLOBAL_DATA_PTR;
-extern void srio_init(void);
-
#ifdef CONFIG_QE
extern qe_iop_conf_t qe_iop_conf_tab[];
extern void qe_config_iopin(u8 port, u8 pin, int dir,
#ifdef CONFIG_SYS_SRIO
srio_init();
+#ifdef CONFIG_SRIOBOOT_MASTER
+ srio_boot_master();
+#ifdef CONFIG_SRIOBOOT_SLAVE_HOLDOFF
+ srio_boot_master_release_slave();
+#endif
+#endif
#endif
#if defined(CONFIG_MP)
/*
- * Copyright 2004, 2007-2011 Freescale Semiconductor, Inc.
+ * Copyright 2004, 2007-2012 Freescale Semiconductor, Inc.
* Copyright (C) 2003 Motorola,Inc.
*
* See file CREDITS for list of people who contributed to this
andi. r1,r3,L1CSR0_DCE@l
beq 2b
+/*
+ * Ne need to setup interrupt vector for NAND SPL
+ * because NAND SPL never compiles it.
+ */
+#if !defined(CONFIG_NAND_SPL)
/* Setup interrupt vectors */
lis r1,CONFIG_SYS_MONITOR_BASE@h
mtspr IVPR,r1
- li r1,0x0100
- mtspr IVOR0,r1 /* 0: Critical input */
- li r1,0x0200
- mtspr IVOR1,r1 /* 1: Machine check */
- li r1,0x0300
- mtspr IVOR2,r1 /* 2: Data storage */
- li r1,0x0400
- mtspr IVOR3,r1 /* 3: Instruction storage */
- li r1,0x0500
- mtspr IVOR4,r1 /* 4: External interrupt */
- li r1,0x0600
- mtspr IVOR5,r1 /* 5: Alignment */
- li r1,0x0700
- mtspr IVOR6,r1 /* 6: Program check */
- li r1,0x0800
- mtspr IVOR7,r1 /* 7: floating point unavailable */
- li r1,0x0900
- mtspr IVOR8,r1 /* 8: System call */
+ lis r3,(CONFIG_SYS_MONITOR_BASE & 0xffff)@h
+ ori r3,r3,(CONFIG_SYS_MONITOR_BASE & 0xffff)@l
+
+ addi r4,r3,CriticalInput - _start + _START_OFFSET
+ mtspr IVOR0,r4 /* 0: Critical input */
+ addi r4,r3,MachineCheck - _start + _START_OFFSET
+ mtspr IVOR1,r4 /* 1: Machine check */
+ addi r4,r3,DataStorage - _start + _START_OFFSET
+ mtspr IVOR2,r4 /* 2: Data storage */
+ addi r4,r3,InstStorage - _start + _START_OFFSET
+ mtspr IVOR3,r4 /* 3: Instruction storage */
+ addi r4,r3,ExtInterrupt - _start + _START_OFFSET
+ mtspr IVOR4,r4 /* 4: External interrupt */
+ addi r4,r3,Alignment - _start + _START_OFFSET
+ mtspr IVOR5,r4 /* 5: Alignment */
+ addi r4,r3,ProgramCheck - _start + _START_OFFSET
+ mtspr IVOR6,r4 /* 6: Program check */
+ addi r4,r3,FPUnavailable - _start + _START_OFFSET
+ mtspr IVOR7,r4 /* 7: floating point unavailable */
+ addi r4,r3,SystemCall - _start + _START_OFFSET
+ mtspr IVOR8,r4 /* 8: System call */
/* 9: Auxiliary processor unavailable(unsupported) */
- li r1,0x0a00
- mtspr IVOR10,r1 /* 10: Decrementer */
- li r1,0x0b00
- mtspr IVOR11,r1 /* 11: Interval timer */
- li r1,0x0c00
- mtspr IVOR12,r1 /* 12: Watchdog timer */
- li r1,0x0d00
- mtspr IVOR13,r1 /* 13: Data TLB error */
- li r1,0x0e00
- mtspr IVOR14,r1 /* 14: Instruction TLB error */
- li r1,0x0f00
- mtspr IVOR15,r1 /* 15: Debug */
+ addi r4,r3,Decrementer - _start + _START_OFFSET
+ mtspr IVOR10,r4 /* 10: Decrementer */
+ addi r4,r3,IntervalTimer - _start + _START_OFFSET
+ mtspr IVOR11,r4 /* 11: Interval timer */
+ addi r4,r3,WatchdogTimer - _start + _START_OFFSET
+ mtspr IVOR12,r4 /* 12: Watchdog timer */
+ addi r4,r3,DataTLBError - _start + _START_OFFSET
+ mtspr IVOR13,r4 /* 13: Data TLB error */
+ addi r4,r3,InstructionTLBError - _start + _START_OFFSET
+ mtspr IVOR14,r4 /* 14: Instruction TLB error */
+ addi r4,r3,DebugBreakpoint - _start + _START_OFFSET
+ mtspr IVOR15,r4 /* 15: Debug */
+#endif
/* Clear and set up some registers. */
li r0,0x0000
ori r2, r2, FSL_BOOKE_MAS2(CONFIG_SYS_CCSRBAR, (MAS2_I|MAS2_G))@l
lis r3, FSL_BOOKE_MAS3(CONFIG_SYS_CCSRBAR_PHYS_LOW, 0, (MAS3_SW|MAS3_SR))@h
ori r3, r3, FSL_BOOKE_MAS3(CONFIG_SYS_CCSRBAR_PHYS_LOW, 0, (MAS3_SW|MAS3_SR))@l
+#ifdef CONFIG_ENABLE_36BIT_PHYS
lis r7, CONFIG_SYS_CCSRBAR_PHYS_HIGH@h
ori r7, r7, CONFIG_SYS_CCSRBAR_PHYS_HIGH@l
+ mtspr MAS7, r7
+#endif
mtspr MAS0, r0
mtspr MAS1, r1
mtspr MAS2, r2
mtspr MAS3, r3
- mtspr MAS7, r7
isync
msync
tlbwe
ori r2, r2, FSL_BOOKE_MAS2(CONFIG_SYS_CCSRBAR + 0x1000, (MAS2_I|MAS2_G))@l
lis r3, FSL_BOOKE_MAS3(CONFIG_SYS_CCSRBAR_DEFAULT, 0, (MAS3_SW|MAS3_SR))@h
ori r3, r3, FSL_BOOKE_MAS3(CONFIG_SYS_CCSRBAR_DEFAULT, 0, (MAS3_SW|MAS3_SR))@l
+#ifdef CONFIG_ENABLE_36BIT_PHYS
li r7, 0 /* The default CCSR address is always a 32-bit number */
+ mtspr MAS7, r7
+#endif
mtspr MAS0, r0
/* MAS1 is the same as above */
mtspr MAS2, r2
mtspr MAS3, r3
- mtspr MAS7, r7
isync
msync
tlbwe
cmplw 0,r7,r8
blt 2b
+ /* Update IVORs as per relocated vector table address */
+ li r7,0x0100
+ mtspr IVOR0,r7 /* 0: Critical input */
+ li r7,0x0200
+ mtspr IVOR1,r7 /* 1: Machine check */
+ li r7,0x0300
+ mtspr IVOR2,r7 /* 2: Data storage */
+ li r7,0x0400
+ mtspr IVOR3,r7 /* 3: Instruction storage */
+ li r7,0x0500
+ mtspr IVOR4,r7 /* 4: External interrupt */
+ li r7,0x0600
+ mtspr IVOR5,r7 /* 5: Alignment */
+ li r7,0x0700
+ mtspr IVOR6,r7 /* 6: Program check */
+ li r7,0x0800
+ mtspr IVOR7,r7 /* 7: floating point unavailable */
+ li r7,0x0900
+ mtspr IVOR8,r7 /* 8: System call */
+ /* 9: Auxiliary processor unavailable(unsupported) */
+ li r7,0x0a00
+ mtspr IVOR10,r7 /* 10: Decrementer */
+ li r7,0x0b00
+ mtspr IVOR11,r7 /* 11: Interval timer */
+ li r7,0x0c00
+ mtspr IVOR12,r7 /* 12: Watchdog timer */
+ li r7,0x0d00
+ mtspr IVOR13,r7 /* 13: Data TLB error */
+ li r7,0x0e00
+ mtspr IVOR14,r7 /* 14: Instruction TLB error */
+ li r7,0x0f00
+ mtspr IVOR15,r7 /* 15: Debug */
+
lis r7,0x0
mtspr IVPR,r7
/*
- * Copyright 2009 Freescale Semiconductor, Inc.
+ * Copyright 2009-2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
.bootpg ADDR(.text) - 0x1000 :
{
- arch/powerpc/cpu/mpc85xx/start.o KEEP(*(.bootpg))
+ KEEP(arch/powerpc/cpu/mpc85xx/start.o (.bootpg))
} :text = 0xffff
. = ADDR(.text) + 0x80000;
#include <config.h>
#include <asm/fsl_law.h>
#include <asm/fsl_serdes.h>
+#include <asm/fsl_srio.h>
+
+#define SRIO_PORT_ACCEPT_ALL 0x10000001
+#define SRIO_IB_ATMU_AR 0x80f55000
+#define SRIO_OB_ATMU_AR_MAINT 0x80077000
+#define SRIO_OB_ATMU_AR_RW 0x80045000
+#define SRIO_LCSBA1CSR_OFFSET 0x5c
+#define SRIO_MAINT_WIN_SIZE 0x1000000 /* 16M */
+#define SRIO_RW_WIN_SIZE 0x100000 /* 1M */
+#define SRIO_LCSBA1CSR 0x60000000
#if defined(CONFIG_FSL_CORENET)
#define _DEVDISR_SRIO1 FSL_CORENET_DEVDISR_SRIO1
setbits_be32(&gur->devdisr, _DEVDISR_RMU);
}
}
+
+#ifdef CONFIG_SRIOBOOT_MASTER
+void srio_boot_master(void)
+{
+ struct ccsr_rio *srio = (void *)CONFIG_SYS_FSL_SRIO_ADDR;
+
+ /* set port accept-all */
+ out_be32((void *)&srio->impl.port[CONFIG_SRIOBOOT_MASTER_PORT].ptaacr,
+ SRIO_PORT_ACCEPT_ALL);
+
+ debug("SRIOBOOT - MASTER: Master port [ %d ] for srio boot.\n",
+ CONFIG_SRIOBOOT_MASTER_PORT);
+ /* configure inbound window for slave's u-boot image */
+ debug("SRIOBOOT - MASTER: Inbound window for slave's image; "
+ "Local = 0x%llx, Srio = 0x%llx, Size = 0x%x\n",
+ (u64)CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS1,
+ (u64)CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS1,
+ CONFIG_SRIOBOOT_SLAVE_IMAGE_SIZE);
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[0].riwtar,
+ CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS1 >> 12);
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[0].riwbar,
+ CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS1 >> 12);
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[0].riwar,
+ SRIO_IB_ATMU_AR
+ | atmu_size_mask(CONFIG_SRIOBOOT_SLAVE_IMAGE_SIZE));
+
+ /* configure inbound window for slave's u-boot image */
+ debug("SRIOBOOT - MASTER: Inbound window for slave's image; "
+ "Local = 0x%llx, Srio = 0x%llx, Size = 0x%x\n",
+ (u64)CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS2,
+ (u64)CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS2,
+ CONFIG_SRIOBOOT_SLAVE_IMAGE_SIZE);
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[1].riwtar,
+ CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS2 >> 12);
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[1].riwbar,
+ CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS2 >> 12);
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[1].riwar,
+ SRIO_IB_ATMU_AR
+ | atmu_size_mask(CONFIG_SRIOBOOT_SLAVE_IMAGE_SIZE));
+
+ /* configure inbound window for slave's ucode */
+ debug("SRIOBOOT - MASTER: Inbound window for slave's ucode; "
+ "Local = 0x%llx, Srio = 0x%llx, Size = 0x%x\n",
+ (u64)CONFIG_SRIOBOOT_SLAVE_UCODE_LAW_PHYS,
+ (u64)CONFIG_SRIOBOOT_SLAVE_UCODE_SRIO_PHYS,
+ CONFIG_SRIOBOOT_SLAVE_UCODE_SIZE);
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[2].riwtar,
+ CONFIG_SRIOBOOT_SLAVE_UCODE_LAW_PHYS >> 12);
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[2].riwbar,
+ CONFIG_SRIOBOOT_SLAVE_UCODE_SRIO_PHYS >> 12);
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[2].riwar,
+ SRIO_IB_ATMU_AR
+ | atmu_size_mask(CONFIG_SRIOBOOT_SLAVE_UCODE_SIZE));
+
+ /* configure inbound window for slave's ENV */
+ debug("SRIOBOOT - MASTER: Inbound window for slave's ENV; "
+ "Local = 0x%llx, Siro = 0x%llx, Size = 0x%x\n",
+ CONFIG_SRIOBOOT_SLAVE_ENV_LAW_PHYS,
+ CONFIG_SRIOBOOT_SLAVE_ENV_SRIO_PHYS,
+ CONFIG_SRIOBOOT_SLAVE_ENV_SIZE);
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[3].riwtar,
+ CONFIG_SRIOBOOT_SLAVE_ENV_LAW_PHYS >> 12);
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[3].riwbar,
+ CONFIG_SRIOBOOT_SLAVE_ENV_SRIO_PHYS >> 12);
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[3].riwar,
+ SRIO_IB_ATMU_AR
+ | atmu_size_mask(CONFIG_SRIOBOOT_SLAVE_ENV_SIZE));
+}
+
+#ifdef CONFIG_SRIOBOOT_SLAVE_HOLDOFF
+void srio_boot_master_release_slave(void)
+{
+ struct ccsr_rio *srio = (void *)CONFIG_SYS_FSL_SRIO_ADDR;
+ u32 escsr;
+ debug("SRIOBOOT - MASTER: "
+ "Check the port status and release slave core ...\n");
+
+ escsr = in_be32((void *)&srio->lp_serial
+ .port[CONFIG_SRIOBOOT_MASTER_PORT].pescsr);
+ if (escsr & 0x2) {
+ if (escsr & 0x10100) {
+ debug("SRIOBOOT - MASTER: Port [ %d ] is error.\n",
+ CONFIG_SRIOBOOT_MASTER_PORT);
+ } else {
+ debug("SRIOBOOT - MASTER: "
+ "Port [ %d ] is ready, now release slave's core ...\n",
+ CONFIG_SRIOBOOT_MASTER_PORT);
+ /*
+ * configure outbound window
+ * with maintenance attribute to set slave's LCSBA1CSR
+ */
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT]
+ .outbw[1].rowtar, 0);
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT]
+ .outbw[1].rowtear, 0);
+ if (CONFIG_SRIOBOOT_MASTER_PORT)
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT]
+ .outbw[1].rowbar,
+ CONFIG_SYS_SRIO2_MEM_PHYS >> 12);
+ else
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT]
+ .outbw[1].rowbar,
+ CONFIG_SYS_SRIO1_MEM_PHYS >> 12);
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT]
+ .outbw[1].rowar,
+ SRIO_OB_ATMU_AR_MAINT
+ | atmu_size_mask(SRIO_MAINT_WIN_SIZE));
+
+ /*
+ * configure outbound window
+ * with R/W attribute to set slave's BRR
+ */
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT]
+ .outbw[2].rowtar,
+ SRIO_LCSBA1CSR >> 9);
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT]
+ .outbw[2].rowtear, 0);
+ if (CONFIG_SRIOBOOT_MASTER_PORT)
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT]
+ .outbw[2].rowbar,
+ (CONFIG_SYS_SRIO2_MEM_PHYS
+ + SRIO_MAINT_WIN_SIZE) >> 12);
+ else
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT]
+ .outbw[2].rowbar,
+ (CONFIG_SYS_SRIO1_MEM_PHYS
+ + SRIO_MAINT_WIN_SIZE) >> 12);
+ out_be32((void *)&srio->atmu
+ .port[CONFIG_SRIOBOOT_MASTER_PORT]
+ .outbw[2].rowar,
+ SRIO_OB_ATMU_AR_RW
+ | atmu_size_mask(SRIO_RW_WIN_SIZE));
+
+ /*
+ * Set the LCSBA1CSR register in slave
+ * by the maint-outbound window
+ */
+ if (CONFIG_SRIOBOOT_MASTER_PORT) {
+ out_be32((void *)CONFIG_SYS_SRIO2_MEM_VIRT
+ + SRIO_LCSBA1CSR_OFFSET,
+ SRIO_LCSBA1CSR);
+ while (in_be32((void *)CONFIG_SYS_SRIO2_MEM_VIRT
+ + SRIO_LCSBA1CSR_OFFSET)
+ != SRIO_LCSBA1CSR)
+ ;
+ /*
+ * And then set the BRR register
+ * to release slave core
+ */
+ out_be32((void *)CONFIG_SYS_SRIO2_MEM_VIRT
+ + SRIO_MAINT_WIN_SIZE
+ + CONFIG_SRIOBOOT_SLAVE_BRR_OFFSET,
+ CONFIG_SRIOBOOT_SLAVE_RELEASE_MASK);
+ } else {
+ out_be32((void *)CONFIG_SYS_SRIO1_MEM_VIRT
+ + SRIO_LCSBA1CSR_OFFSET,
+ SRIO_LCSBA1CSR);
+ while (in_be32((void *)CONFIG_SYS_SRIO1_MEM_VIRT
+ + SRIO_LCSBA1CSR_OFFSET)
+ != SRIO_LCSBA1CSR)
+ ;
+ /*
+ * And then set the BRR register
+ * to release slave core
+ */
+ out_be32((void *)CONFIG_SYS_SRIO1_MEM_VIRT
+ + SRIO_MAINT_WIN_SIZE
+ + CONFIG_SRIOBOOT_SLAVE_BRR_OFFSET,
+ CONFIG_SRIOBOOT_SLAVE_RELEASE_MASK);
+ }
+ debug("SRIOBOOT - MASTER: "
+ "Release slave successfully! Now the slave should start up!\n");
+ }
+ } else
+ debug("SRIOBOOT - MASTER: Port [ %d ] is not ready.\n",
+ CONFIG_SRIOBOOT_MASTER_PORT);
+}
+#endif
+#endif
#define CONFIG_SYS_FSL_ERRATUM_NMG_DDR120
#define CONFIG_SYS_FSL_ERRATUM_NMG_LBC103
#define CONFIG_SYS_FSL_ERRATUM_NMG_ETSEC129
+#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 1
+#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9
+#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5
+#define CONFIG_SYS_FSL_RMU
+#define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2
#elif defined(CONFIG_MPC8555)
#define CONFIG_MAX_CPUS 1
#define MAX_QE_RISC 2
#define QE_NUM_OF_SNUM 28
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
+#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 1
+#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9
+#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5
+#define CONFIG_SYS_FSL_RMU
+#define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2
#elif defined(CONFIG_MPC8569)
#define CONFIG_MAX_CPUS 1
#define MAX_QE_RISC 4
#define QE_NUM_OF_SNUM 46
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
+#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 1
+#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9
+#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5
+#define CONFIG_SYS_FSL_RMU
+#define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2
#elif defined(CONFIG_MPC8572)
#define CONFIG_MAX_CPUS 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define CONFIG_SYS_FSL_ERRATUM_ESDHC_A001
+#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2
+#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9
+#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5
+#define CONFIG_SYS_FSL_RMU
+#define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2
#elif defined(CONFIG_PPC_P2040)
#define CONFIG_MAX_CPUS 4
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define CONFIG_SYS_FSL_ERRATUM_CPU_A003999
#define CONFIG_SYS_FSL_ERRATUM_DDR_A003474
+#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2
+#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9
+#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5
#elif defined(CONFIG_PPC_P2041)
#define CONFIG_MAX_CPUS 4
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define CONFIG_SYS_FSL_ERRATUM_CPU_A003999
#define CONFIG_SYS_FSL_ERRATUM_DDR_A003474
+#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2
+#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9
+#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5
#elif defined(CONFIG_PPC_P3041)
#define CONFIG_MAX_CPUS 4
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define CONFIG_SYS_FSL_ERRATUM_CPU_A003999
#define CONFIG_SYS_FSL_ERRATUM_DDR_A003474
+#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2
+#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9
+#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5
#elif defined(CONFIG_PPC_P3060)
#define CONFIG_MAX_CPUS 8
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000
#define CONFIG_SYS_FSL_ERRATUM_DDR_A003
#define CONFIG_SYS_FSL_ERRATUM_CPU_A003999
+#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2
+#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9
+#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5
#elif defined(CONFIG_PPC_P4040)
#define CONFIG_MAX_CPUS 4
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000
#define CONFIG_SYS_FSL_ERRATUM_CPU_A003999
#define CONFIG_SYS_FSL_ERRATUM_DDR_A003474
+#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2
+#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9
+#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5
#elif defined(CONFIG_PPC_P4080)
#define CONFIG_MAX_CPUS 8
#define CONFIG_SYS_P4080_ERRATUM_SERDES_A005
#define CONFIG_SYS_FSL_ERRATUM_CPU_A003999
#define CONFIG_SYS_FSL_ERRATUM_DDR_A003474
+#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2
+#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9
+#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5
+#define CONFIG_SYS_FSL_RMU
+#define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2
/* P5010 is single core version of P5020 */
#elif defined(CONFIG_PPC_P5010)
#define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define CONFIG_SYS_FSL_ERRATUM_DDR_A003474
+#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2
+#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9
+#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5
#elif defined(CONFIG_PPC_P5020)
#define CONFIG_MAX_CPUS 2
#define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define CONFIG_SYS_FSL_ERRATUM_DDR_A003474
+#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2
+#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9
+#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5
#else
#error Processor type not defined for this platform
--- /dev/null
+/*
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _FSL_SRIO_H_
+#define _FSL_SRIO_H_
+
+enum atmu_size {
+ ATMU_SIZE_4K = 0xb,
+ ATMU_SIZE_8K,
+ ATMU_SIZE_16K,
+ ATMU_SIZE_32K,
+ ATMU_SIZE_64K,
+ ATMU_SIZE_128K,
+ ATMU_SIZE_256K,
+ ATMU_SIZE_512K,
+ ATMU_SIZE_1M,
+ ATMU_SIZE_2M,
+ ATMU_SIZE_4M,
+ ATMU_SIZE_8M,
+ ATMU_SIZE_16M,
+ ATMU_SIZE_32M,
+ ATMU_SIZE_64M,
+ ATMU_SIZE_128M,
+ ATMU_SIZE_256M,
+ ATMU_SIZE_512M,
+ ATMU_SIZE_1G,
+ ATMU_SIZE_2G,
+ ATMU_SIZE_4G,
+ ATMU_SIZE_8G,
+ ATMU_SIZE_16G,
+ ATMU_SIZE_32G,
+ ATMU_SIZE_64G,
+};
+
+#define atmu_size_mask(sz) (__ilog2_u64(sz) - 1)
+#define atmu_size_bytes(x) (1ULL << ((x & 0x3f) + 1))
+
+extern void srio_init(void);
+#ifdef CONFIG_SRIOBOOT_MASTER
+extern void srio_boot_master(void);
+#ifdef CONFIG_SRIOBOOT_SLAVE_HOLDOFF
+extern void srio_boot_master_release_slave(void);
+#endif
+#endif
+#endif
} ccsr_cpm_t;
#endif
-/* RapidIO Registers */
-typedef struct ccsr_rio {
- u32 didcar; /* Device Identity Capability */
- u32 dicar; /* Device Information Capability */
- u32 aidcar; /* Assembly Identity Capability */
- u32 aicar; /* Assembly Information Capability */
- u32 pefcar; /* Processing Element Features Capability */
- u32 spicar; /* Switch Port Information Capability */
- u32 socar; /* Source Operations Capability */
- u32 docar; /* Destination Operations Capability */
+#ifdef CONFIG_SYS_SRIO
+/* Architectural regsiters */
+struct rio_arch {
+ u32 didcar; /* Device Identity CAR */
+ u32 dicar; /* Device Information CAR */
+ u32 aidcar; /* Assembly Identity CAR */
+ u32 aicar; /* Assembly Information CAR */
+ u32 pefcar; /* Processing Element Features CAR */
+ u8 res0[4];
+ u32 socar; /* Source Operations CAR */
+ u32 docar; /* Destination Operations CAR */
u8 res1[32];
- u32 msr; /* Mailbox Cmd And Status */
- u32 pwdcsr; /* Port-Write & Doorbell Cmd And Status */
+ u32 mcsr; /* Mailbox CSR */
+ u32 pwdcsr; /* Port-Write and Doorbell CSR */
u8 res2[4];
u32 pellccsr; /* Processing Element Logic Layer CCSR */
u8 res3[12];
- u32 lcsbacsr; /* Local Cfg Space Base Addr Cmd & Status */
- u32 bdidcsr; /* Base Device ID Cmd & Status */
+ u32 lcsbacsr; /* Local Configuration Space BACSR */
+ u32 bdidcsr; /* Base Device ID CSR */
u8 res4[4];
- u32 hbdidlcsr; /* Host Base Device ID Lock Cmd & Status */
- u32 ctcsr; /* Component Tag Cmd & Status */
- u8 res5[144];
- u32 pmbh0csr; /* Port Maint. Block Hdr 0 Cmd & Status */
- u8 res6[28];
- u32 pltoccsr; /* Port Link Time-out Ctrl Cmd & Status */
- u32 prtoccsr; /* Port Response Time-out Ctrl Cmd & Status */
- u8 res7[20];
- u32 pgccsr; /* Port General Cmd & Status */
- u32 plmreqcsr; /* Port Link Maint. Request Cmd & Status */
- u32 plmrespcsr; /* Port Link Maint. Response Cmd & Status */
- u32 plascsr; /* Port Local Ackid Status Cmd & Status */
- u8 res8[12];
- u32 pescsr; /* Port Error & Status Cmd & Status */
- u32 pccsr; /* Port Control Cmd & Status */
- u8 res9[65184];
- u32 cr; /* Port Control Cmd & Status */
- u8 res10[12];
- u32 pcr; /* Port Configuration */
- u32 peir; /* Port Error Injection */
- u8 res11[3048];
- u32 rowtar0; /* RIO Outbound Window Translation Addr 0 */
- u8 res12[12];
- u32 rowar0; /* RIO Outbound Attrs 0 */
- u8 res13[12];
- u32 rowtar1; /* RIO Outbound Window Translation Addr 1 */
- u8 res14[4];
- u32 rowbar1; /* RIO Outbound Window Base Addr 1 */
- u8 res15[4];
- u32 rowar1; /* RIO Outbound Attrs 1 */
- u8 res16[12];
- u32 rowtar2; /* RIO Outbound Window Translation Addr 2 */
- u8 res17[4];
- u32 rowbar2; /* RIO Outbound Window Base Addr 2 */
- u8 res18[4];
- u32 rowar2; /* RIO Outbound Attrs 2 */
- u8 res19[12];
- u32 rowtar3; /* RIO Outbound Window Translation Addr 3 */
- u8 res20[4];
- u32 rowbar3; /* RIO Outbound Window Base Addr 3 */
- u8 res21[4];
- u32 rowar3; /* RIO Outbound Attrs 3 */
- u8 res22[12];
- u32 rowtar4; /* RIO Outbound Window Translation Addr 4 */
- u8 res23[4];
- u32 rowbar4; /* RIO Outbound Window Base Addr 4 */
- u8 res24[4];
- u32 rowar4; /* RIO Outbound Attrs 4 */
- u8 res25[12];
- u32 rowtar5; /* RIO Outbound Window Translation Addr 5 */
- u8 res26[4];
- u32 rowbar5; /* RIO Outbound Window Base Addr 5 */
- u8 res27[4];
- u32 rowar5; /* RIO Outbound Attrs 5 */
- u8 res28[12];
- u32 rowtar6; /* RIO Outbound Window Translation Addr 6 */
- u8 res29[4];
- u32 rowbar6; /* RIO Outbound Window Base Addr 6 */
- u8 res30[4];
- u32 rowar6; /* RIO Outbound Attrs 6 */
- u8 res31[12];
- u32 rowtar7; /* RIO Outbound Window Translation Addr 7 */
- u8 res32[4];
- u32 rowbar7; /* RIO Outbound Window Base Addr 7 */
- u8 res33[4];
- u32 rowar7; /* RIO Outbound Attrs 7 */
- u8 res34[12];
- u32 rowtar8; /* RIO Outbound Window Translation Addr 8 */
- u8 res35[4];
- u32 rowbar8; /* RIO Outbound Window Base Addr 8 */
- u8 res36[4];
- u32 rowar8; /* RIO Outbound Attrs 8 */
- u8 res37[76];
- u32 riwtar4; /* RIO Inbound Window Translation Addr 4 */
- u8 res38[4];
- u32 riwbar4; /* RIO Inbound Window Base Addr 4 */
- u8 res39[4];
- u32 riwar4; /* RIO Inbound Attrs 4 */
- u8 res40[12];
- u32 riwtar3; /* RIO Inbound Window Translation Addr 3 */
- u8 res41[4];
- u32 riwbar3; /* RIO Inbound Window Base Addr 3 */
- u8 res42[4];
- u32 riwar3; /* RIO Inbound Attrs 3 */
- u8 res43[12];
- u32 riwtar2; /* RIO Inbound Window Translation Addr 2 */
- u8 res44[4];
- u32 riwbar2; /* RIO Inbound Window Base Addr 2 */
- u8 res45[4];
- u32 riwar2; /* RIO Inbound Attrs 2 */
- u8 res46[12];
- u32 riwtar1; /* RIO Inbound Window Translation Addr 1 */
- u8 res47[4];
- u32 riwbar1; /* RIO Inbound Window Base Addr 1 */
- u8 res48[4];
- u32 riwar1; /* RIO Inbound Attrs 1 */
- u8 res49[12];
- u32 riwtar0; /* RIO Inbound Window Translation Addr 0 */
- u8 res50[12];
- u32 riwar0; /* RIO Inbound Attrs 0 */
- u8 res51[12];
- u32 pnfedr; /* Port Notification/Fatal Error Detect */
- u32 pnfedir; /* Port Notification/Fatal Error Detect */
- u32 pnfeier; /* Port Notification/Fatal Error IRQ Enable */
- u32 pecr; /* Port Error Control */
- u32 pepcsr0; /* Port Error Packet/Control Symbol 0 */
- u32 pepr1; /* Port Error Packet 1 */
- u32 pepr2; /* Port Error Packet 2 */
- u8 res52[4];
- u32 predr; /* Port Recoverable Error Detect */
- u8 res53[4];
- u32 pertr; /* Port Error Recovery Threshold */
- u32 prtr; /* Port Retry Threshold */
- u8 res54[464];
- u32 omr; /* Outbound Mode */
- u32 osr; /* Outbound Status */
- u32 eodqtpar; /* Extended Outbound Desc Queue Tail Ptr Addr */
- u32 odqtpar; /* Outbound Desc Queue Tail Ptr Addr */
- u32 eosar; /* Extended Outbound Unit Source Addr */
- u32 osar; /* Outbound Unit Source Addr */
- u32 odpr; /* Outbound Destination Port */
- u32 odatr; /* Outbound Destination Attrs */
- u32 odcr; /* Outbound Doubleword Count */
- u32 eodqhpar; /* Extended Outbound Desc Queue Head Ptr Addr */
- u32 odqhpar; /* Outbound Desc Queue Head Ptr Addr */
- u8 res55[52];
- u32 imr; /* Outbound Mode */
- u32 isr; /* Inbound Status */
- u32 eidqtpar; /* Extended Inbound Desc Queue Tail Ptr Addr */
- u32 idqtpar; /* Inbound Desc Queue Tail Ptr Addr */
- u32 eifqhpar; /* Extended Inbound Frame Queue Head Ptr Addr */
- u32 ifqhpar; /* Inbound Frame Queue Head Ptr Addr */
- u8 res56[1000];
- u32 dmr; /* Doorbell Mode */
- u32 dsr; /* Doorbell Status */
- u32 edqtpar; /* Extended Doorbell Queue Tail Ptr Addr */
- u32 dqtpar; /* Doorbell Queue Tail Ptr Addr */
- u32 edqhpar; /* Extended Doorbell Queue Head Ptr Addr */
- u32 dqhpar; /* Doorbell Queue Head Ptr Addr */
- u8 res57[104];
- u32 pwmr; /* Port-Write Mode */
- u32 pwsr; /* Port-Write Status */
- u32 epwqbar; /* Extended Port-Write Queue Base Addr */
- u32 pwqbar; /* Port-Write Queue Base Addr */
- u8 res58[60176];
-} ccsr_rio_t;
+ u32 hbdidlcsr; /* Host Base Device ID Lock CSR */
+ u32 ctcsr; /* Component Tag CSR */
+};
+
+/* Extended Features Space: 1x/4x LP-Serial Port registers */
+struct rio_lp_serial_port {
+ u32 plmreqcsr; /* Port Link Maintenance Request CSR */
+ u32 plmrespcsr; /* Port Link Maintenance Response CS */
+ u32 plascsr; /* Port Local Ackid Status CSR */
+ u8 res0[12];
+ u32 pescsr; /* Port Error and Status CSR */
+ u32 pccsr; /* Port Control CSR */
+};
+
+/* Extended Features Space: 1x/4x LP-Serial registers */
+struct rio_lp_serial {
+ u32 pmbh0csr; /* Port Maintenance Block Header 0 CSR */
+ u8 res0[28];
+ u32 pltoccsr; /* Port Link Time-out CCSR */
+ u32 prtoccsr; /* Port Response Time-out CCSR */
+ u8 res1[20];
+ u32 pgccsr; /* Port General CSR */
+ struct rio_lp_serial_port port[CONFIG_SYS_FSL_SRIO_MAX_PORTS];
+};
+
+/* Logical error reporting registers */
+struct rio_logical_err {
+ u32 erbh; /* Error Reporting Block Header Register */
+ u8 res0[4];
+ u32 ltledcsr; /* Logical/Transport layer error DCSR */
+ u32 ltleecsr; /* Logical/Transport layer error ECSR */
+ u8 res1[4];
+ u32 ltlaccsr; /* Logical/Transport layer ACCSR */
+ u32 ltldidccsr; /* Logical/Transport layer DID CCSR */
+ u32 ltlcccsr; /* Logical/Transport layer control CCSR */
+};
+
+/* Physical error reporting port registers */
+struct rio_phys_err_port {
+ u32 edcsr; /* Port error detect CSR */
+ u32 erecsr; /* Port error rate enable CSR */
+ u32 ecacsr; /* Port error capture attributes CSR */
+ u32 pcseccsr0; /* Port packet/control symbol ECCSR 0 */
+ u32 peccsr[3]; /* Port error capture CSR */
+ u8 res0[12];
+ u32 ercsr; /* Port error rate CSR */
+ u32 ertcsr; /* Port error rate threshold CSR */
+ u8 res1[16];
+};
+
+/* Physical error reporting registers */
+struct rio_phys_err {
+ struct rio_phys_err_port port[CONFIG_SYS_FSL_SRIO_MAX_PORTS];
+};
+
+/* Implementation Space: General Port-Common */
+struct rio_impl_common {
+ u8 res0[4];
+ u32 llcr; /* Logical Layer Configuration Register */
+ u8 res1[8];
+ u32 epwisr; /* Error / Port-Write Interrupt SR */
+ u8 res2[12];
+ u32 lretcr; /* Logical Retry Error Threshold CR */
+ u8 res3[92];
+ u32 pretcr; /* Physical Retry Erorr Threshold CR */
+ u8 res4[124];
+};
+
+/* Implementation Space: Port Specific */
+struct rio_impl_port_spec {
+ u32 adidcsr; /* Port Alt. Device ID CSR */
+ u8 res0[28];
+ u32 ptaacr; /* Port Pass-Through/Accept-All CR */
+ u32 lopttlcr;
+ u8 res1[8];
+ u32 iecsr; /* Port Implementation Error CSR */
+ u8 res2[12];
+ u32 pcr; /* Port Phsyical Configuration Register */
+ u8 res3[20];
+ u32 slcsr; /* Port Serial Link CSR */
+ u8 res4[4];
+ u32 sleicr; /* Port Serial Link Error Injection */
+ u32 a0txcr; /* Port Arbitration 0 Tx CR */
+ u32 a1txcr; /* Port Arbitration 1 Tx CR */
+ u32 a2txcr; /* Port Arbitration 2 Tx CR */
+ u32 mreqtxbacr[3]; /* Port Request Tx Buffer ACR */
+ u32 mrspfctxbacr; /* Port Response/Flow Control Tx Buffer ACR */
+};
+
+/* Implementation Space: register */
+struct rio_implement {
+ struct rio_impl_common com;
+ struct rio_impl_port_spec port[CONFIG_SYS_FSL_SRIO_MAX_PORTS];
+};
+
+/* Revision Control Register */
+struct rio_rev_ctrl {
+ u32 ipbrr[2]; /* IP Block Revision Register */
+};
+
+struct rio_atmu_row {
+ u32 rowtar; /* RapidIO Outbound Window TAR */
+ u32 rowtear; /* RapidIO Outbound Window TEAR */
+ u32 rowbar;
+ u8 res0[4];
+ u32 rowar; /* RapidIO Outbound Attributes Register */
+ u32 rowsr[3]; /* Port RapidIO outbound window segment register */
+};
+
+struct rio_atmu_riw {
+ u32 riwtar; /* RapidIO Inbound Window Translation AR */
+ u8 res0[4];
+ u32 riwbar; /* RapidIO Inbound Window Base AR */
+ u8 res1[4];
+ u32 riwar; /* RapidIO Inbound Attributes Register */
+ u8 res2[12];
+};
+
+/* ATMU window registers */
+struct rio_atmu_win {
+ struct rio_atmu_row outbw[CONFIG_SYS_FSL_SRIO_OB_WIN_NUM];
+ u8 res0[64];
+ struct rio_atmu_riw inbw[CONFIG_SYS_FSL_SRIO_IB_WIN_NUM];
+};
+
+struct rio_atmu {
+ struct rio_atmu_win port[CONFIG_SYS_FSL_SRIO_MAX_PORTS];
+};
+
+#ifdef CONFIG_SYS_FSL_RMU
+struct rio_msg {
+ u32 omr; /* Outbound Mode Register */
+ u32 osr; /* Outbound Status Register */
+ u32 eodqdpar; /* Extended Outbound DQ DPAR */
+ u32 odqdpar; /* Outbound Descriptor Queue DPAR */
+ u32 eosar; /* Extended Outbound Unit Source AR */
+ u32 osar; /* Outbound Unit Source AR */
+ u32 odpr; /* Outbound Destination Port Register */
+ u32 odatr; /* Outbound Destination Attributes Register */
+ u32 odcr; /* Outbound Doubleword Count Register */
+ u32 eodqepar; /* Extended Outbound DQ EPAR */
+ u32 odqepar; /* Outbound Descriptor Queue EPAR */
+ u32 oretr; /* Outbound Retry Error Threshold Register */
+ u32 omgr; /* Outbound Multicast Group Register */
+ u32 omlr; /* Outbound Multicast List Register */
+ u8 res0[40];
+ u32 imr; /* Outbound Mode Register */
+ u32 isr; /* Inbound Status Register */
+ u32 eidqdpar; /* Extended Inbound Descriptor Queue DPAR */
+ u32 idqdpar; /* Inbound Descriptor Queue DPAR */
+ u32 eifqepar; /* Extended Inbound Frame Queue EPAR */
+ u32 ifqepar; /* Inbound Frame Queue EPAR */
+ u32 imirir; /* Inbound Maximum Interrutp RIR */
+ u8 res1[4];
+ u32 eihqepar; /* Extended inbound message header queue EPAR */
+ u32 ihqepar; /* Inbound message header queue EPAR */
+ u8 res2[120];
+};
+
+struct rio_dbell {
+ u32 odmr; /* Outbound Doorbell Mode Register */
+ u32 odsr; /* Outbound Doorbell Status Register */
+ u8 res0[16];
+ u32 oddpr; /* Outbound Doorbell Destination Port */
+ u32 oddatr; /* Outbound Doorbell Destination AR */
+ u8 res1[12];
+ u32 oddretr; /* Outbound Doorbell Retry Threshold CR */
+ u8 res2[48];
+ u32 idmr; /* Inbound Doorbell Mode Register */
+ u32 idsr; /* Inbound Doorbell Status Register */
+ u32 iedqdpar; /* Extended Inbound Doorbell Queue DPAR */
+ u32 iqdpar; /* Inbound Doorbell Queue DPAR */
+ u32 iedqepar; /* Extended Inbound Doorbell Queue EPAR */
+ u32 idqepar; /* Inbound Doorbell Queue EPAR */
+ u32 idmirir; /* Inbound Doorbell Max Interrupt RIR */
+};
+
+struct rio_pw {
+ u32 pwmr; /* Port-Write Mode Register */
+ u32 pwsr; /* Port-Write Status Register */
+ u32 epwqbar; /* Extended Port-Write Queue BAR */
+ u32 pwqbar; /* Port-Write Queue Base Address Register */
+};
+#endif
+
+/* RapidIO Registers */
+struct ccsr_rio {
+ struct rio_arch arch;
+ u8 res0[144];
+ struct rio_lp_serial lp_serial;
+ u8 res1[1152];
+ struct rio_logical_err logical_err;
+ u8 res2[32];
+ struct rio_phys_err phys_err;
+ u8 res3[63808];
+ struct rio_implement impl;
+ u8 res4[2552];
+ struct rio_rev_ctrl rev;
+ struct rio_atmu atmu;
+#ifdef CONFIG_SYS_FSL_RMU
+ u8 res5[8192];
+ struct rio_msg msg[CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM];
+ u8 res6[512];
+ struct rio_dbell dbell;
+ u8 res7[100];
+ struct rio_pw pw;
+#endif
+};
+#endif
/* Quick Engine Block Pin Muxing Registers */
typedef struct par_io {
#define CONFIG_SYS_MPC85xx_PIC_OFFSET 0x40000
#define CONFIG_SYS_MPC85xx_GUTS_OFFSET 0xE0000
+#define CONFIG_SYS_FSL_SRIO_OFFSET 0xC0000
#define CONFIG_SYS_FSL_CPC_ADDR \
(CONFIG_SYS_CCSRBAR + CONFIG_SYS_FSL_CPC_OFFSET)
(CONFIG_SYS_IMMR + CONFIG_SYS_FSL_FM1_DTSEC1_OFFSET)
#define CONFIG_SYS_FSL_FM2_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_FSL_FM2_OFFSET)
+#define CONFIG_SYS_FSL_SRIO_ADDR \
+ (CONFIG_SYS_IMMR + CONFIG_SYS_FSL_SRIO_OFFSET)
#define CONFIG_SYS_PCI1_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_PCI1_OFFSET)
#ifdef CONFIG_SYS_NAND_BASE_PHYS
SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
#endif
+#ifdef CONFIG_SRIOBOOT_SLAVE
+#if defined(CONFIG_SRIOBOOT_SLAVE_PORT0)
+ SET_LAW(CONFIG_SYS_SRIOBOOT_SLAVE_ADDR_PHYS,
+ LAW_SIZE_1M, LAW_TRGT_IF_RIO_1),
+ SET_LAW(CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR_PHYS,
+ LAW_SIZE_1M, LAW_TRGT_IF_RIO_1),
+#elif defined(CONFIG_SRIOBOOT_SLAVE_PORT1)
+ SET_LAW(CONFIG_SYS_SRIOBOOT_SLAVE_ADDR_PHYS,
+ LAW_SIZE_1M, LAW_TRGT_IF_RIO_2),
+ SET_LAW(CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR_PHYS,
+ LAW_SIZE_1M, LAW_TRGT_IF_RIO_2),
+#endif
+#endif
};
int num_law_entries = ARRAY_SIZE(law_table);
SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 0, BOOKE_PAGESZ_1M, 1),
+#elif defined(CONFIG_SRIOBOOT_SLAVE)
+ /*
+ * SRIOBOOT-SLAVE. When slave boot, the address of the
+ * space is at 0xfff00000, it covered the 0xfffff000.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_SRIOBOOT_SLAVE_ADDR,
+ CONFIG_SYS_SRIOBOOT_SLAVE_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_1M, 1),
#else
SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 16, BOOKE_PAGESZ_1M, 1),
#endif
+#ifdef CONFIG_SRIOBOOT_SLAVE
+ /*
+ * SRIOBOOT-SLAVE. 1M space from 0xffe00000 for fetching ucode
+ * and ENV from master
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR,
+ CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
+ 0, 17, BOOKE_PAGESZ_1M, 1),
+#endif
};
int num_tlb_entries = ARRAY_SIZE(tlb_table);
else
printf("invalid setting of SW%u\n", PIXIS_LBMAP_SWITCH);
-#ifdef CONFIG_PHYS_64BIT
- puts("36-bit Addressing\n");
-#endif
-
/* Display the RCW, so that no one gets confused as to what RCW
* we're actually using for this boot.
*/
u8 vboot;
u8 *pixis_base = (u8 *)PIXIS_BASE;
- puts("Board: MPC8536DS ");
-#ifdef CONFIG_PHYS_64BIT
- puts("(36-bit addrmap) ");
-#endif
-
- printf ("Sys ID: 0x%02x, "
+ printf("Board: MPC8536DS Sys ID: 0x%02x, "
"Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER),
in_8(pixis_base + PIXIS_PVER));
u8 vboot;
u8 *pixis_base = (u8 *)PIXIS_BASE;
- puts ("Board: MPC8572DS ");
-#ifdef CONFIG_PHYS_64BIT
- puts ("(36-bit addrmap) ");
-#endif
- printf ("Sys ID: 0x%02x, "
+ printf("Board: MPC8572DS Sys ID: 0x%02x, "
"Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER),
in_8(pixis_base + PIXIS_PVER));
else
puts ("Promjet\n");
-#ifdef CONFIG_PHYS_64BIT
- printf (" 36-bit physical address map\n");
-#endif
return 0;
}
DECLARE_GLOBAL_DATA_PTR;
-#ifndef CONFIG_DDR_RAW_TIMING
+#ifndef CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_SYS_DRAM_SIZE 1024
fsl_ddr_cfg_regs_t ddr_cfg_regs_800 = {
return ddr_size;
}
-#else /* CONFIG_DDR_RAW_TIMING */
+#else /* CONFIG_SYS_DDR_RAW_TIMING */
/*
* Samsung K4B2G0846C-HCF8
* The following timing are for "downshift"
}
}
-#endif /* CONFIG_DDR_RAW_TIMING */
+#endif /* CONFIG_SYS_DDR_RAW_TIMING */
struct cpu_type *cpu;
cpu = gd->cpu;
- printf("Board: %sRDB ", cpu->name);
-#ifdef CONFIG_PHYS_64BIT
- puts("(36-bit addrmap)");
-#endif
- puts("\n");
+ printf("Board: %sRDB\n", cpu->name);
return 0;
}
{
u8 sw;
- puts("Board: P1022DS ");
-#ifdef CONFIG_PHYS_64BIT
- puts("(36-bit addrmap) ");
-#endif
-
- printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
+ printf("Board: P1022DS Sys ID: 0x%02x, "
+ "Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
in_8(&pixis->id), in_8(&pixis->arch), in_8(&pixis->scver));
sw = in_8(&PIXIS_SW(PIXIS_LBMAP_SWITCH));
fdt_fixup_memory(blob, (u64)base, (u64)size);
+ /* By default NOR is on, and NAND is disabled */
+#ifdef CONFIG_NAND_U_BOOT
+ do_fixup_by_path_string(blob, "nor_flash", "status", "disabled");
+ do_fixup_by_path_string(blob, "nand_flash", "status", "okay");
+#endif
+
fdt_fixup_fman_ethernet(blob);
}
#endif
cpu = gd->cpu;
printf ("Board: %sRDB Rev%c\n", cpu->name, board_rev);
-#ifdef CONFIG_PHYS_64BIT
- puts ("(36-bit addrmap) \n");
-#endif
+
setbits_be32(&pgpio->gpdir, GPIO_DIR);
/*
#include <asm/io.h>
#include <asm/fsl_law.h>
-#ifdef CONFIG_DDR_RAW_TIMING
+#ifdef CONFIG_SYS_DDR_RAW_TIMING
#if defined(CONFIG_P1020RDB_PROTO) || \
defined(CONFIG_P1021RDB) || \
defined(CONFIG_P1020UTM)
return 0;
}
-#endif /* CONFIG_DDR_RAW_TIMING */
+#endif /* CONFIG_SYS_DDR_RAW_TIMING */
/* Fixed sdram init -- doesn't use serial presence detect. */
phys_size_t fixed_sdram(void)
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
u8 in, out, io_config, val;
- printf("Board: %s ", CONFIG_BOARDNAME);
-
-#ifdef CONFIG_PHYS_64BIT
- puts("(36-bit addrmap) ");
-#endif
-
- printf("CPLD: V%d.%d PCBA: V%d.0\n",
+ printf("Board: %s CPLD: V%d.%d PCBA: V%d.0\n", CONFIG_BOARDNAME,
in_8(&cpld_data->cpld_rev_major) & 0x0F,
in_8(&cpld_data->cpld_rev_minor) & 0x0F,
in_8(&cpld_data->pcba_rev) & 0x0F);
{
u8 sw;
- puts("Board: P2020DS ");
-#ifdef CONFIG_PHYS_64BIT
- puts("(36-bit addrmap) ");
-#endif
-
- printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
+ printf("Board: P2020DS Sys ID: 0x%02x, "
+ "Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
in_8(&pixis->id), in_8(&pixis->arch), in_8(&pixis->scver));
sw = in_8(&PIXIS_SW(PIXIS_LBMAP_SWITCH));
sw = CPLD_READ(fbank_sel);
printf("vBank: %d\n", sw & 0x1);
-#ifdef CONFIG_PHYS_64BIT
- puts("36-bit Addressing\n");
-#endif
-
/*
* Display the RCW, so that no one gets confused as to what RCW
* we're actually using for this boot.
else
printf("invalid setting of SW%u\n", PIXIS_LBMAP_SWITCH);
-#ifdef CONFIG_PHYS_64BIT
- puts("36-bit Addressing\n");
-#endif
puts("Reset Configuration Word (RCW):");
for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) {
u32 rcw = in_be32(&gur->rcwsr[i]);
P2020RDB_SDCARD powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2020RDB,SDCARD
P2020RDB_SPIFLASH powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2020RDB,SPIFLASH
P2041RDB powerpc mpc85xx p2041rdb freescale
+P2041RDB_NAND powerpc mpc85xx p2041rdb freescale - P2041RDB:RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000
P2041RDB_SDCARD powerpc mpc85xx p2041rdb freescale - P2041RDB:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000
P2041RDB_SECURE_BOOT powerpc mpc85xx p2041rdb freescale - P2041RDB:SECURE_BOOT
P2041RDB_SPIFLASH powerpc mpc85xx p2041rdb freescale - P2041RDB:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000
P3041DS_SDCARD powerpc mpc85xx corenet_ds freescale - P3041DS:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000
P3041DS_SECURE_BOOT powerpc mpc85xx corenet_ds freescale - P3041DS:SECURE_BOOT
P3041DS_SPIFLASH powerpc mpc85xx corenet_ds freescale - P3041DS:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000
+P3041DS_SRIOBOOT_MASTER powerpc mpc85xx corenet_ds freescale - P3041DS:SRIOBOOT_MASTER
+P3041DS_SRIOBOOT_SLAVE powerpc mpc85xx corenet_ds freescale - P3041DS:SRIOBOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000
P3060QDS powerpc mpc85xx p3060qds freescale
P3060QDS_NAND powerpc mpc85xx p3060qds freescale - P3060QDS:RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000
P3060QDS_SECURE_BOOT powerpc mpc85xx p3060qds freescale - P3060QDS:SECURE_BOOT
P4080DS_SDCARD powerpc mpc85xx corenet_ds freescale - P4080DS:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000
P4080DS_SECURE_BOOT powerpc mpc85xx corenet_ds freescale - P4080DS:SECURE_BOOT
P4080DS_SPIFLASH powerpc mpc85xx corenet_ds freescale - P4080DS:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000
+P4080DS_SRIOBOOT_MASTER powerpc mpc85xx corenet_ds freescale - P4080DS:SRIOBOOT_MASTER
+P4080DS_SRIOBOOT_SLAVE powerpc mpc85xx corenet_ds freescale - P4080DS:SRIOBOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000
P5020DS powerpc mpc85xx corenet_ds freescale
P5020DS_NAND powerpc mpc85xx corenet_ds freescale - P5020DS:RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000
P5020DS_SDCARD powerpc mpc85xx corenet_ds freescale - P5020DS:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000
P5020DS_SECURE_BOOT powerpc mpc85xx corenet_ds freescale - P5020DS:SECURE_BOOT
P5020DS_SPIFLASH powerpc mpc85xx corenet_ds freescale - P5020DS:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000
+P5020DS_SRIOBOOT_MASTER powerpc mpc85xx corenet_ds freescale - P5020DS:SRIOBOOT_MASTER
+P5020DS_SRIOBOOT_SLAVE powerpc mpc85xx corenet_ds freescale - P5020DS:SRIOBOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000
stxgp3 powerpc mpc85xx stxgp3 stx
stxssa powerpc mpc85xx stxssa stx - stxssa
stxssa_4M powerpc mpc85xx stxssa stx - stxssa:STXSSA_4M
COBJS-$(CONFIG_ENV_IS_IN_NVRAM) += env_nvram.o
COBJS-$(CONFIG_ENV_IS_IN_ONENAND) += env_onenand.o
COBJS-$(CONFIG_ENV_IS_IN_SPI_FLASH) += env_sf.o
+COBJS-$(CONFIG_ENV_IS_IN_REMOTE) += env_remote.o
COBJS-$(CONFIG_ENV_IS_NOWHERE) += env_nowhere.o
# command
print_mhz("pevfreq", bd->bi_pevfreq);
#endif
+#ifdef CONFIG_ENABLE_36BIT_PHYS
+#ifdef CONFIG_PHYS_64BIT
+ puts("addressing = 36-bit\n");
+#else
+ puts("addressing = 32-bit\n");
+#endif
+#endif
+
print_eth(0);
#if defined(CONFIG_HAS_ETH1)
print_eth(1);
!defined(CONFIG_ENV_IS_IN_NVRAM) && \
!defined(CONFIG_ENV_IS_IN_ONENAND) && \
!defined(CONFIG_ENV_IS_IN_SPI_FLASH) && \
+ !defined(CONFIG_ENV_IS_IN_REMOTE) && \
!defined(CONFIG_ENV_IS_NOWHERE)
# error Define one of CONFIG_ENV_IS_IN_{EEPROM|FLASH|DATAFLASH|ONENAND|\
-SPI_FLASH|MG_DISK|NVRAM|MMC|FAT} or CONFIG_ENV_IS_NOWHERE
+SPI_FLASH|MG_DISK|NVRAM|MMC|FAT|REMOTE} or CONFIG_ENV_IS_NOWHERE
#endif
#define XMK_STR(x) #x
--- /dev/null
+/*
+ * (C) Copyright 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* #define DEBUG */
+
+#include <common.h>
+#include <command.h>
+#include <environment.h>
+#include <linux/stddef.h>
+
+char *env_name_spec = "Remote";
+
+#ifdef ENV_IS_EMBEDDED
+env_t *env_ptr = &environment;
+#else /* ! ENV_IS_EMBEDDED */
+env_t *env_ptr = (env_t *)CONFIG_ENV_ADDR;
+#endif /* ENV_IS_EMBEDDED */
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#if !defined(CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_OFFSET 0
+#endif
+
+uchar env_get_char_spec(int index)
+{
+ return *((uchar *)(gd->env_addr + index));
+}
+
+int env_init(void)
+{
+ if (crc32(0, env_ptr->data, ENV_SIZE) == env_ptr->crc) {
+ gd->env_addr = (ulong)&(env_ptr->data);
+ gd->env_valid = 1;
+ return 0;
+ }
+
+ gd->env_addr = (ulong)default_environment;
+ gd->env_valid = 0;
+ return 0;
+}
+
+#ifdef CONFIG_CMD_SAVEENV
+int saveenv(void)
+{
+#ifdef CONFIG_SRIOBOOT_SLAVE
+ printf("Can not support the 'saveenv' when boot from SRIO!\n");
+ return 1;
+#else
+ return 0;
+#endif
+}
+#endif /* CONFIG_CMD_SAVEENV */
+
+void env_relocate_spec(void)
+{
+#ifndef ENV_IS_EMBEDDED
+ env_import((char *)env_ptr, 1);
+#endif
+}
--- /dev/null
+------------------------------
+SRIO Boot on Corenet Platforms
+------------------------------
+
+For some PowerPC processors with SRIO interface, boot location can be configured
+to SRIO by RCW. The processor booting from SRIO can do without flash for u-boot
+image, ucode and ENV. All the images can be fetched from another processor's
+memory space by SRIO link connected between them.
+
+This document describes the processes based on an example implemented on P4080DS
+platforms and a RCW example with boot from SRIO configuration.
+
+Environment of the SRIO boot:
+ a) Master and slave can be SOCs in one board or SOCs in separate boards.
+ b) They are connected with SRIO links, whether 1x or 4x, and directly or
+ through switch system.
+ c) Only Master has NorFlash for booting, and all the Master's and Slave's
+ U-Boot images, UCodes will be stored in this flash.
+ d) Slave has its own EEPROM for RCW and PBI.
+ e) Slave's RCW should configure the SerDes for SRIO boot port, set the boot
+ location to SRIO, and holdoff all the cores if needed.
+
+ ---------- ----------- -----------
+ | | | | | |
+ | | | | | |
+ | NorFlash|<----->| Master | SRIO | Slave |<---->[EEPROM]
+ | | | |<===========>| |
+ | | | | | |
+ ---------- ----------- -----------
+
+The example based on P4080DS platform:
+ Two P4080DS platforms can be used to implement the boot from SRIO. Their SRIO
+ ports 0 will be connected directly and will be used for the boot from SRIO.
+
+ 1. Slave's RCW example for boot from SRIO port 0 and core 0 not in holdoff.
+ 00000000: aa55 aa55 010e 0100 0c58 0000 0000 0000
+ 00000010: 1818 1818 0000 8888 7440 4000 0000 2000
+ 00000020: f400 0000 0100 0000 0000 0000 0000 0000
+ 00000030: 0000 0000 0083 0000 0000 0000 0000 0000
+ 00000040: 0000 0000 0000 0000 0813 8040 698b 93fe
+
+ 2. Slave's RCW example for boot from SRIO port 0 and all cores in holdoff.
+ 00000000: aa55 aa55 010e 0100 0c58 0000 0000 0000
+ 00000010: 1818 1818 0000 8888 7440 4000 0000 2000
+ 00000020: f440 0000 0100 0000 0000 0000 0000 0000
+ 00000030: 0000 0000 0083 0000 0000 0000 0000 0000
+ 00000040: 0000 0000 0000 0000 0813 8040 063c 778f
+
+ 3. Sequence in Step by Step.
+ a) Update RCW for slave with boot from SRIO port 0 configuration.
+ b) Program slave's U-Boot image, UCode, and ENV parameters into master's
+ NorFlash.
+ c) Start up master and it will boot up normally from its NorFlash.
+ Then, it will finish necessary configurations for slave's boot from
+ SRIO port 0.
+ d) Master will set inbound SRIO windows covered slave's U-Boot image stored
+ in master's NorFlash.
+ e) Master will set an inbound SRIO window covered slave's UCode stored in
+ master's NorFlash.
+ f) Master will set an inbound SRIO window covered slave's ENV stored in
+ master's NorFlash.
+ g) If need to release slave's core, master will set outbound SRIO windows
+ in order to configure slave's registers for the core's releasing.
+ h) If all cores of slave in holdoff, slave should be powered on before all
+ the above master's steps, and wait to be released by master. If not all
+ cores in holdoff, that means core 0 will start up normally, slave should
+ be powered on after all the above master's steps. In the startup phase
+ of the slave from SRIO, it will finish some necessary configurations.
+ i) Slave will set a specific TLB entry for the boot process.
+ j) Slave will set a LAW entry with the TargetID SRIO port 0 for the boot.
+ k) Slave will set a specific TLB entry in order to fetch UCode and ENV
+ from master.
+ l) Slave will set a LAW entry with the TargetID SRIO port 0 for UCode and ENV.
+
+How to use this feature:
+ To use this feature, you need to focus three points.
+
+ 1. Slave's RCW with SRIO boot configurations, and all cores in holdoff
+ configurations if needed.
+ Please refer to the examples given above.
+
+ 2. U-Boot image's compilation.
+ For master, U-Boot image should be generated specifically by
+
+ make xxxx_SRIOBOOT_MASTER_config.
+
+ For example, master U-Boot image used on P4080DS should be compiled with
+
+ make P4080DS_SRIOBOOT_MASTER_config.
+
+ For slave, U-Boot image should be generated specifically by
+
+ make xxxx_SRIOBOOT_SLAVE_config.
+
+ For example, slave U-Boot image used on P4080DS should be compiled with
+
+ make P4080DS_SRIOBOOT_SLAVE_config.
+
+ 3. Necessary modifications based on a specific environment.
+ For a specific environment, the SRIO port for boot, the addresses of the
+ slave's U-Boot image, UCode, ENV stored in master's NorFlash, and any other
+ configurations can be modified in the file:
+ include/configs/corenet_ds.h.
/* flush cache after read */
flush_cache((ulong)addr, cnt * 512);
}
+#elif defined(CONFIG_SYS_QE_FMAN_FW_IN_REMOTE)
+ void *addr = (void *)CONFIG_SYS_QE_FMAN_FW_ADDR;
#endif
/* Upload the Fman microcode if it's present */
/* DDR Setup */
#define CONFIG_FSL_DDR3
-#define CONFIG_DDR_RAW_TIMING
+#define CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 1
#define SPD_EEPROM_ADDRESS 0x52
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_OFFSET (512 * 1097)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \
#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
#endif
-#define CONFIG_SYS_BR0_PRELIM \
+#define CONFIG_SYS_FLASH_BR_PRELIM \
(BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
-#define CONFIG_SYS_OR0_PRELIM ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \
- | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR)
+#define CONFIG_SYS_FLASH_OR_PRELIM \
+ ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \
+ | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR)
#define CONFIG_FSL_CPLD
#define CPLD_BASE 0xffdf0000 /* CPLD registers */
#define CONFIG_SYS_RAMBOOT
#endif
+#define CONFIG_NAND_FSL_ELBC
+/* Nand Flash */
+#ifdef CONFIG_NAND_FSL_ELBC
+#define CONFIG_SYS_NAND_BASE 0xffa00000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull
+#else
+#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
+#endif
+
+#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+/* NAND flash config */
+#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
+ | BR_PS_8 /* Port Size = 8 bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V) /* valid */
+#define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \
+ | OR_FCM_PGS /* Large Page*/ \
+ | OR_FCM_CSCT \
+ | OR_FCM_CST \
+ | OR_FCM_CHT \
+ | OR_FCM_SCY_1 \
+ | OR_FCM_TRLX \
+ | OR_FCM_EHTR)
+
+#ifdef CONFIG_NAND
+#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
+#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
+#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
+#else
+#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
+#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
+#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
+#endif
+#else
+#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
+#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
+#endif /* CONFIG_NAND_FSL_ELBC */
+
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
#endif
+#ifdef CONFIG_SRIOBOOT_SLAVE
+/* Set 1M boot space */
+#define CONFIG_SYS_SRIOBOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
+#define CONFIG_SYS_SRIOBOOT_SLAVE_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIOBOOT_SLAVE_ADDR)
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_SYS_NO_FLASH
+#endif
+
/* High Level Configuration Options */
#define CONFIG_BOOKE
#define CONFIG_E500 /* BOOKE e500 family */
#define CONFIG_ENV_OVERWRITE
#ifdef CONFIG_SYS_NO_FLASH
+#ifndef CONFIG_SRIOBOOT_SLAVE
#define CONFIG_ENV_IS_NOWHERE
+#endif
#else
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIOBOOT_SLAVE)
+#define CONFIG_ENV_IS_IN_REMOTE
+#define CONFIG_ENV_ADDR 0xffe20000
+#define CONFIG_ENV_SIZE 0x2000
+#elif defined(CONFIG_ENV_IS_NOWHERE)
+#define CONFIG_ENV_SIZE 0x2000
#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#endif
#define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */
+/*
+ * SRIOBOOT - MASTER
+ */
+#ifdef CONFIG_SRIOBOOT_MASTER
+/* master port for srioboot*/
+#define CONFIG_SRIOBOOT_MASTER_PORT 0
+/* #define CONFIG_SRIOBOOT_MASTER_PORT 1 */
+/*
+ * for slave u-boot IMAGE instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS1 0xfef080000ull
+#define CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS1 0xfff80000ull
+#define CONFIG_SRIOBOOT_SLAVE_IMAGE_SIZE 0x80000 /* 512K */
+#define CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS2 0xfef080000ull
+#define CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS2 0x3fff80000ull
+/*
+ * for slave UCODE instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIOBOOT_SLAVE_UCODE_LAW_PHYS 0xfef020000ull
+#define CONFIG_SRIOBOOT_SLAVE_UCODE_SRIO_PHYS 0x3ffe00000ull
+#define CONFIG_SRIOBOOT_SLAVE_UCODE_SIZE 0x10000 /* 64K */
+/*
+ * for slave ENV instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIOBOOT_SLAVE_ENV_LAW_PHYS 0xfef060000ull
+#define CONFIG_SRIOBOOT_SLAVE_ENV_SRIO_PHYS 0x3ffe20000ull
+#define CONFIG_SRIOBOOT_SLAVE_ENV_SIZE 0x20000 /* 128K */
+/* slave core release by master*/
+#define CONFIG_SRIOBOOT_SLAVE_HOLDOFF
+#define CONFIG_SRIOBOOT_SLAVE_BRR_OFFSET 0xe00e4
+#define CONFIG_SRIOBOOT_SLAVE_RELEASE_MASK 0x00000001 /* release core 0 */
+#endif
+
+/*
+ * SRIOBOOT - SLAVE
+ */
+#ifdef CONFIG_SRIOBOOT_SLAVE
+/* slave port for srioboot */
+#define CONFIG_SRIOBOOT_SLAVE_PORT0
+/* #define CONFIG_SRIOBOOT_SLAVE_PORT1 */
+#define CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR 0xFFE00000
+#define CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR)
+#endif
+
/*
* eSPI - Enhanced SPI
*/
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIOBOOT_SLAVE)
+/*
+ * Slave has no ucode locally, it can fetch this from remote. When implementing
+ * in two corenet boards, slave's ucode could be stored in master's memory
+ * space, the address can be mapped from slave TLB->slave LAW->
+ * slave SRIO outbound window->master inbound window->master LAW->
+ * the ucode address in master's NOR flash.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000
#else
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEF000000
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CMD_SATA
-#define CONFIG_SATA_SIL3114
+#define CONFIG_SATA_SIL
#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_LIBATA
#define CONFIG_LBA48
/* DDR Setup */
#define CONFIG_FSL_DDR3
-#define CONFIG_DDR_RAW_TIMING
+#define CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 1
#define SPD_EEPROM_ADDRESS 0x52
projects / u-boot / commitdiff