#include <command.h>
#include <malloc.h>
#include <asm/arch/ixp425.h>
-
+#include <asm/io.h>
#include <miiphy.h>
+#ifdef CONFIG_PCI
+#include <pci.h>
+#include <asm/arch/ixp425pci.h>
+#endif
#include "actux4_hw.h"
DECLARE_GLOBAL_DATA_PTR;
-int board_init (void)
+int board_early_init_f(void)
+{
+ writel(0xbd113c42, IXP425_EXP_CS1);
+ return 0;
+}
+
+int board_init(void)
{
gd->bd->bi_arch_number = MACH_TYPE_ACTUX4;
/* adress of boot parameters */
gd->bd->bi_boot_params = 0x00000100;
- GPIO_OUTPUT_CLEAR (CONFIG_SYS_GPIO_nPWRON);
- GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_nPWRON);
+ GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_nPWRON);
+ GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_nPWRON);
- GPIO_OUTPUT_CLEAR (CONFIG_SYS_GPIO_IORST);
- GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_IORST);
+ GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
+ GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST);
/* led not populated on board*/
- GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_LED3);
- GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_LED3);
+ GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED3);
+ GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED3);
/* middle LED */
- GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_LED2);
- GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_LED2);
+ GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED2);
+ GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED2);
/* right LED */
/* weak pulldown = LED weak on */
- GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_LED1);
- GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_LED1);
+ GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_LED1);
+ GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED1);
/* Setup GPIO's for Interrupt inputs */
- GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_USBINTA);
- GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_USBINTB);
- GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_USBINTC);
- GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_RTCINT);
- GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_PCI_INTA);
- GPIO_OUTPUT_DISABLE (CONFIG_SYS_GPIO_PCI_INTB);
-
- GPIO_INT_ACT_LOW_SET (CONFIG_SYS_GPIO_USBINTA);
- GPIO_INT_ACT_LOW_SET (CONFIG_SYS_GPIO_USBINTB);
- GPIO_INT_ACT_LOW_SET (CONFIG_SYS_GPIO_USBINTC);
- GPIO_INT_ACT_LOW_SET (CONFIG_SYS_GPIO_RTCINT);
- GPIO_INT_ACT_LOW_SET (CONFIG_SYS_GPIO_PCI_INTA);
- GPIO_INT_ACT_LOW_SET (CONFIG_SYS_GPIO_PCI_INTB);
+ GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTA);
+ GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTB);
+ GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTC);
+ GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_RTCINT);
+ GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTA);
+ GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTB);
+
+ GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTA);
+ GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTB);
+ GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTC);
+ GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_RTCINT);
+ GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTA);
+ GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTB);
/* Setup GPIO's for 33MHz clock output */
- *IXP425_GPIO_GPCLKR = 0x011001FF;
- GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_EXTBUS_CLK);
- GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_PCI_CLK);
-
- *IXP425_EXP_CS1 = 0xbd113c42;
+ writel(0x011001FF, IXP425_GPIO_GPCLKR);
+ GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
+ GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
- udelay (10000);
- GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_IORST);
- udelay (10000);
- GPIO_OUTPUT_CLEAR (CONFIG_SYS_GPIO_IORST);
- udelay (10000);
- GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_IORST);
+ udelay(10000);
+ GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
+ udelay(10000);
+ GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
+ udelay(10000);
+ GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
return 0;
}
/* Check Board Identity */
-int checkboard (void)
+int checkboard(void)
{
- puts ("Board: AcTux-4\n");
- return (0);
+ puts("Board: AcTux-4\n");
+ return 0;
}
-int dram_init (void)
+int dram_init(void)
{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+ gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20);
+ return 0;
+}
- return (0);
+#ifdef CONFIG_PCI
+struct pci_controller hose;
+
+void pci_init_board(void)
+{
+ pci_ixp_init(&hose);
}
+#endif
/*
* Hardcoded flash setup:
* Flash 0 is a non-CFI SST 39VF020 flash, 8 bit flash / 8 bit bus.
* Flash 1 is an Intel *16 flash using the CFI driver.
*/
-ulong board_flash_get_legacy (ulong base, int banknum, flash_info_t * info)
+ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info)
{
if (banknum == 0) { /* non-CFI boot flash */
info->portwidth = 1;
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 3
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_BOARD_EARLY_INIT_F 1
/***************************************************************
* U-boot generic defines start here.
***************************************************************/
-#undef CONFIG_USE_IRQ
-
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
#define CONFIG_CMD_ELF
+#define CONFIG_PCI
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_PCI_PNP
+#define CONFIG_IXP_PCI
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_CMD_PCI_ENUM
+#endif
+
#define CONFIG_BOOTCOMMAND "run boot_flash"
/* enable passing of ATAGs */
#define CONFIG_CMDLINE_TAG 1
#define CONFIG_SYS_MEMTEST_START 0x00400000
#define CONFIG_SYS_MEMTEST_END 0x00800000
-/* spec says 66.666 MHz, but it appears to be 33 */
-#define CONFIG_SYS_HZ 3333333
+/* timer clock - 2* OSC_IN system clock */
+#define CONFIG_IXP425_TIMER_CLK 66000000
+#define CONFIG_SYS_HZ 1000
/* default load address */
#define CONFIG_SYS_LOAD_ADDR 0x00010000
* The stack sizes are set up in start.S using the settings below
*/
#define CONFIG_STACKSIZE (128*1024) /* regular stack */
-#ifdef CONFIG_USE_IRQ
-# define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
-# define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
-#endif
/* Expansion bus settings */
#define CONFIG_SYS_EXP_CS0 0xbd113003
/* SDRAM settings */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 0x00000000
-#define CONFIG_SYS_DRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
/* 32MB SDRAM */
#define CONFIG_SYS_SDR_CONFIG 0x18
#define CONFIG_SYS_DRAM_SIZE 0x02000000
/* FLASH organization */
+#define CONFIG_SYS_TEXT_BASE 0x50000000
#define CONFIG_SYS_MAX_FLASH_BANKS 2
/* max # of sectors per chip */
#define CONFIG_SYS_MAX_FLASH_SECT 70
#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1
#define CONFIG_SYS_MONITOR_LEN (252 << 10)
+#define CONFIG_BOARD_SIZE_LIMIT 258048
/* Use common CFI driver */
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_PHY_ADDR 0x1C
/* MII PHY management */
#define CONFIG_MII 1
+
/* Number of ethernet rx buffers & descriptors */
#define CONFIG_SYS_RX_ETH_BUFFER 16
"mtd=IXP4XX-Flash.0:252k(uboot),4k(uboot_env);" \
"IXP4XX-Flash.1:128k(ucode),1280k(linux),-(root)\0" \
"kerneladdr=51020000\0" \
+ "kernelfile=actux4/uImage\0" \
+ "rootfile=actux4/rootfs\0" \
"rootaddr=51160000\0" \
"loadaddr=10000\0" \
"updateboot_ser=mw.b 10000 ff 40000;" \
" loady ${loadaddr};" \
" run eraseboot writeboot\0" \
"updateboot_net=mw.b 10000 ff 40000;" \
- " tftp ${loadaddr} u-boot.bin;" \
+ " tftp ${loadaddr} actux4/u-boot.bin;" \
" run eraseboot writeboot\0" \
"eraseboot=protect off 50000000 5003efff;" \
" erase 50000000 +${filesize}\0" \
"writeboot=cp.b 10000 50000000 ${filesize}\0" \
- "eraseenv=protect off 5003f000 5003ffff;" \
- " erase 5003f000 5003ffff\0" \
+ "updateucode=loady;" \
+ " era ${npe_ucode} +${filesize};" \
+ " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \
"updateroot=tftp ${loadaddr} ${rootfile};" \
" era ${rootaddr} +${filesize};" \
" cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \
" tftpboot ${loadaddr} ${kernelfile};" \
" bootm\0"
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
#endif /* __CONFIG_H */
projects / u-boot / commitdiff