@$(MKCONFIG) -a nhk8815 arm arm926ejs nhk8815 st nomadik
omap1510inn_config : unconfig
- @$(MKCONFIG) $(@:_config=) arm arm925t omap1510inn
+ @$(MKCONFIG) $(@:_config=) arm arm925t omap1510inn ti
xtract_omap1610xxx = $(subst _cs0boot,,$(subst _cs3boot,,$(subst _cs_autoboot,,$(subst _config,,$1))))
echo "#define CONFIG_CS3_BOOT" >> $(obj)include/config.h ; \
$(XECHO) "... configured for CS3 boot"; \
fi;
- @$(MKCONFIG) -a $(call xtract_omap1610xxx,$@) arm arm926ejs omap1610inn NULL omap
+ @$(MKCONFIG) -a $(call xtract_omap1610xxx,$@) arm arm926ejs omap1610inn ti omap
omap5912osk_config : unconfig
- @$(MKCONFIG) $(@:_config=) arm arm926ejs omap5912osk NULL omap
+ @$(MKCONFIG) $(@:_config=) arm arm926ejs omap5912osk ti omap
xtract_omap730p2 = $(subst _cs0boot,,$(subst _cs3boot,, $(subst _config,,$1)))
echo "#define CONFIG_CS3_BOOT" >> $(obj)include/config.h ; \
$(XECHO) "... configured for CS3 boot"; \
fi;
- @$(MKCONFIG) -a $(call xtract_omap730p2,$@) arm arm926ejs omap730p2 NULL omap
+ @$(MKCONFIG) -a $(call xtract_omap730p2,$@) arm arm926ejs omap730p2 ti omap
rd6281a_config: unconfig
@$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
#########################################################################
omap3_beagle_config : unconfig
- @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 beagle omap3 omap3
+ @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 beagle ti omap3
omap3_overo_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 overo omap3 omap3
omap3_evm_config : unconfig
- @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 evm omap3 omap3
+ @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 evm ti omap3
omap3_pandora_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 pandora omap3 omap3
@$(MKCONFIG) -a mx31pdk arm arm1136 mx31pdk freescale mx31
omap2420h4_config : unconfig
- @$(MKCONFIG) $(@:_config=) arm arm1136 omap2420h4 NULL omap24xx
+ @$(MKCONFIG) $(@:_config=) arm arm1136 omap2420h4 ti omap24xx
qong_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm1136 qong davedenx mx31
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = $(obj)lib$(BOARD).a
-
-COBJS := omap1510innovator.o
-SOBJS := lowlevel_init.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-$(LIB): $(obj).depend $(OBJS) $(SOBJS)
- $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
-
-clean:
- rm -f $(SOBJS) $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
+++ /dev/null
-#
-# (C) Copyright 2002
-# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
-# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
-#
-# (C) Copyright 2003
-# Texas Instruments, <www.ti.com>
-# Kshitij Gupta <Kshitij@ti.com>
-#
-# TI Innovator board with OMAP1510 (ARM925T) cpu
-# see http://www.ti.com/ for more information on Texas Insturments
-#
-# Innovator has 1 bank of 256 MB SDRAM
-# Physical Address:
-# 1000'0000 to 2000'0000
-#
-#
-# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000 (mem base + reserved)
-#
-# we load ourself to 1108'0000
-#
-#
-
-
-TEXT_BASE = 0x11080000
+++ /dev/null
-/*
- * Board specific setup info
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- *
- * -- Some bits of code used from rrload's head_OMAP1510.s --
- * Copyright (C) 2002 RidgeRun, Inc.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-
-#if defined(CONFIG_OMAP1510)
-#include <./configs/omap1510.h>
-#endif
-
-#define OMAP1510_CLKS ((1<<EN_XORPCK)|(1<<EN_PERCK)|(1<<EN_TIMCK)|(1<<EN_GPIOCK))
-
-
-_TEXT_BASE:
- .word TEXT_BASE /* sdram load addr from config.mk */
-
-.globl lowlevel_init
-lowlevel_init:
-
- /*
- * Configure 1510 pins functions to match our board.
- */
- ldr r0, REG_PULL_DWN_CTRL_0
- ldr r1, VAL_PULL_DWN_CTRL_0
- str r1, [r0]
- ldr r0, REG_PULL_DWN_CTRL_1
- ldr r1, VAL_PULL_DWN_CTRL_1
- str r1, [r0]
- ldr r0, REG_PULL_DWN_CTRL_2
- ldr r1, VAL_PULL_DWN_CTRL_2
- str r1, [r0]
- ldr r0, REG_PULL_DWN_CTRL_3
- ldr r1, VAL_PULL_DWN_CTRL_3
- str r1, [r0]
- ldr r0, REG_FUNC_MUX_CTRL_4
- ldr r1, VAL_FUNC_MUX_CTRL_4
- str r1, [r0]
- ldr r0, REG_FUNC_MUX_CTRL_5
- ldr r1, VAL_FUNC_MUX_CTRL_5
- str r1, [r0]
- ldr r0, REG_FUNC_MUX_CTRL_6
- ldr r1, VAL_FUNC_MUX_CTRL_6
- str r1, [r0]
- ldr r0, REG_FUNC_MUX_CTRL_7
- ldr r1, VAL_FUNC_MUX_CTRL_7
- str r1, [r0]
- ldr r0, REG_FUNC_MUX_CTRL_8
- ldr r1, VAL_FUNC_MUX_CTRL_8
- str r1, [r0]
- ldr r0, REG_FUNC_MUX_CTRL_9
- ldr r1, VAL_FUNC_MUX_CTRL_9
- str r1, [r0]
- ldr r0, REG_FUNC_MUX_CTRL_A
- ldr r1, VAL_FUNC_MUX_CTRL_A
- str r1, [r0]
- ldr r0, REG_FUNC_MUX_CTRL_B
- ldr r1, VAL_FUNC_MUX_CTRL_B
- str r1, [r0]
- ldr r0, REG_FUNC_MUX_CTRL_C
- ldr r1, VAL_FUNC_MUX_CTRL_C
- str r1, [r0]
- ldr r0, REG_FUNC_MUX_CTRL_D
- ldr r1, VAL_FUNC_MUX_CTRL_D
- str r1, [r0]
- ldr r0, REG_VOLTAGE_CTRL_0
- ldr r1, VAL_VOLTAGE_CTRL_0
- str r1, [r0]
- ldr r0, REG_TEST_DBG_CTRL_0
- ldr r1, VAL_TEST_DBG_CTRL_0
- str r1, [r0]
- ldr r0, REG_MOD_CONF_CTRL_0
- ldr r1, VAL_MOD_CONF_CTRL_0
- str r1, [r0]
-
- /* Move to 1510 mode */
- ldr r0, REG_COMP_MODE_CTRL_0
- ldr r1, VAL_COMP_MODE_CTRL_0
- str r1, [r0]
-
- /* Set up Traffic Ctlr*/
- ldr r0, REG_TC_IMIF_PRIO
- mov r1, #0x0
- str r1, [r0]
- ldr r0, REG_TC_EMIFS_PRIO
- str r1, [r0]
- ldr r0, REG_TC_EMIFF_PRIO
- str r1, [r0]
-
- ldr r0, REG_TC_EMIFS_CONFIG
- ldr r1, [r0]
- bic r1, r1, #0x08 /* clear the global power-down enable PDE bit */
- bic r1, r1, #0x01 /* write protect flash by clearing the WP bit */
- str r1, [r0] /* EMIFS GlB Configuration. (value 0x12 most likely) */
-
- /* Setup some clock domains */
- ldr r1, =OMAP1510_CLKS
- ldr r0, REG_ARM_IDLECT2
- strh r1, [r0] /* CLKM, Clock domain control. */
-
- mov r1, #0x01 /* PER_EN bit */
- ldr r0, REG_ARM_RSTCT2
- strh r1, [r0] /* CLKM; Peripheral reset. */
-
- /* Set CLKM to Sync-Scalable */
- /* I supposidly need to enable the dsp clock before switching */
- mov r1, #0x1000
- ldr r0, REG_ARM_SYSST
- strh r1, [r0]
- mov r0, #0x400
-1:
- subs r0, r0, #0x1 /* wait for any bubbles to finish */
- bne 1b
-
- ldr r1, VAL_ARM_CKCTL /* use 12Mhz ref, PER must be <= 50Mhz so /2 */
- ldr r0, REG_ARM_CKCTL
- strh r1, [r0]
-
- /* setup DPLL 1 */
- ldr r1, VAL_DPLL1_CTL
- ldr r0, REG_DPLL1_CTL
- strh r1, [r0]
- ands r1, r1, #0x10 /* Check if PLL is enabled. */
- beq lock_end /* Do not look for lock if BYPASS selected */
-2:
- ldrh r1, [r0]
- ands r1, r1, #0x01 /* Check the LOCK bit. */
- beq 2b /* ...loop until bit goes hi. */
-lock_end:
-
- /* Set memory timings corresponding to the new clock speed */
-
- /* Check execution location to determine current execution location
- * and branch to appropriate initialization code.
- */
- mov r0, #0x10000000 /* Load physical SDRAM base. */
- mov r1, pc /* Get current execution location. */
- /* Zero all but top 6 bits of PC, as they alone detect whether an
- * address is in the range 0x1000:0000-0x13ff:ffff, the 64M sized
- * valid range for SDRAM on the OMAP 1510/5910.
- */
- and r1, r1, #0xfc000000
- cmp r1, r0 /* Compare. */
- beq skip_sdram /* Skip over EMIF-fast initialization
- * if running from SDRAM.
- */
-
- /*
- * Delay for SDRAM initialization.
- */
- mov r3, #0x1800 /* value should be checked */
-3:
- subs r3, r3, #0x1 /* Decrement count */
- bne 3b
-
- /*
- * Set SDRAM control values. Disable refresh before MRS command.
- */
- ldr r0, VAL_TC_EMIFF_SDRAM_CONFIG /* get good value */
- bic r3, r0, #0xC /* (BIT3|BIT2) ulConfig with auto-refresh disabled. */
- orr r3, r3, #0x8000000 /* (BIT27) Disable CLK when Power down or Self-Refresh */
- orr r3, r3, #0x4000000 /* BIT26 Power Down Enable */
- ldr r2, REG_TC_EMIFF_SDRAM_CONFIG /* Point to configuration register. */
- str r3, [r2] /* Store the passed value with AR disabled. */
-
- ldr r1, VAL_TC_EMIFF_MRS /* get MRS value */
- ldr r2, REG_TC_EMIFF_MRS /* Point to MRS register. */
- str r1, [r2] /* Store the passed value.*/
-
- ldr r2, REG_TC_EMIFF_SDRAM_CONFIG /* Point to configuration register. */
- str r0, [r2] /* Store the passed value. */
-
- /*
- * Delay for SDRAM initialization.
- */
- mov r3, #0x1800
-4:
- subs r3, r3, #1 /* Decrement count. */
- bne 4b
-
-skip_sdram:
-
- /* slow interface */
- ldr r1, VAL_TC_EMIFS_CS0_CONFIG
- ldr r0, REG_TC_EMIFS_CS0_CONFIG
- str r1, [r0] /* Chip Select 0 */
- ldr r1, VAL_TC_EMIFS_CS1_CONFIG
- ldr r0, REG_TC_EMIFS_CS1_CONFIG
- str r1, [r0] /* Chip Select 1 */
- ldr r1, VAL_TC_EMIFS_CS2_CONFIG
- ldr r0, REG_TC_EMIFS_CS2_CONFIG
- str r1, [r0] /* Chip Select 2 */
- ldr r1, VAL_TC_EMIFS_CS3_CONFIG
- ldr r0, REG_TC_EMIFS_CS3_CONFIG
- str r1, [r0] /* Chip Select 3 */
-
- /* Next, Enable the RS232 Line Drivers in the FPGA. */
- /* Also, power on the audio CODEC's amplifier here, */
- /* which will make a noise on the audio output. */
- /* This is done here instead of in the kernel so there */
- /* isn't a loud popping noise at the start of each */
- /* song. */
- /* Also, disable the CODEC's clocks. */
- /* omap1510-HelenP1 [specific] */
-
- ldr r0, REG_FPGA_POWER
- mov r1, #0
- ldr r2, REG_FPGA_DIP_SWITCH
- ldrb r3, [r2]
- cmp r3, #0x8
- movne r1, #0x62 /* Enable the RS232 Line Drivers in the EPLD */
- strb r1, [r0]
- ldr r0, REG_FPGA_AUDIO
- mov r1, #0x0 /* Disable sound driver (CODEC clocks) */
- strb r1, [r0]
-
- /* back to arch calling code */
- mov pc, lr
-
-/* the literal pools origin */
- .ltorg
-
-/* OMAP configuration registers */
-REG_FUNC_MUX_CTRL_0: /* 32 bits */
- .word 0xfffe1000
-REG_FUNC_MUX_CTRL_1: /* 32 bits */
- .word 0xfffe1004
-REG_FUNC_MUX_CTRL_2: /* 32 bits */
- .word 0xfffe1008
-REG_COMP_MODE_CTRL_0: /* 32 bits */
- .word 0xfffe100c
-REG_FUNC_MUX_CTRL_3: /* 32 bits */
- .word 0xfffe1010
-REG_FUNC_MUX_CTRL_4: /* 32 bits */
- .word 0xfffe1014
-REG_FUNC_MUX_CTRL_5: /* 32 bits */
- .word 0xfffe1018
-REG_FUNC_MUX_CTRL_6: /* 32 bits */
- .word 0xfffe101c
-REG_FUNC_MUX_CTRL_7: /* 32 bits */
- .word 0xfffe1020
-REG_FUNC_MUX_CTRL_8: /* 32 bits */
- .word 0xfffe1024
-REG_FUNC_MUX_CTRL_9: /* 32 bits */
- .word 0xfffe1028
-REG_FUNC_MUX_CTRL_A: /* 32 bits */
- .word 0xfffe102C
-REG_FUNC_MUX_CTRL_B: /* 32 bits */
- .word 0xfffe1030
-REG_FUNC_MUX_CTRL_C: /* 32 bits */
- .word 0xfffe1034
-REG_FUNC_MUX_CTRL_D: /* 32 bits */
- .word 0xfffe1038
-REG_PULL_DWN_CTRL_0: /* 32 bits */
- .word 0xfffe1040
-REG_PULL_DWN_CTRL_1: /* 32 bits */
- .word 0xfffe1044
-REG_PULL_DWN_CTRL_2: /* 32 bits */
- .word 0xfffe1048
-REG_PULL_DWN_CTRL_3: /* 32 bits */
- .word 0xfffe104c
-REG_VOLTAGE_CTRL_0: /* 32 bits */
- .word 0xfffe1060
-REG_TEST_DBG_CTRL_0: /* 32 bits */
- .word 0xfffe1070
-REG_MOD_CONF_CTRL_0: /* 32 bits */
- .word 0xfffe1080
-REG_TC_IMIF_PRIO: /* 32 bits */
- .word 0xfffecc00
-REG_TC_EMIFS_PRIO: /* 32 bits */
- .word 0xfffecc04
-REG_TC_EMIFF_PRIO: /* 32 bits */
- .word 0xfffecc08
-REG_TC_EMIFS_CONFIG: /* 32 bits */
- .word 0xfffecc0c
-REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */
- .word 0xfffecc10
-REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */
- .word 0xfffecc14
-REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */
- .word 0xfffecc18
-REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */
- .word 0xfffecc1c
-REG_TC_EMIFF_SDRAM_CONFIG: /* 32 bits */
- .word 0xfffecc20
-REG_TC_EMIFF_MRS: /* 32 bits */
- .word 0xfffecc24
-/* MPU clock/reset/power mode control registers */
-REG_ARM_CKCTL: /* 16 bits */
- .word 0xfffece00
-REG_ARM_IDLECT2: /* 16 bits */
- .word 0xfffece08
-REG_ARM_RSTCT2: /* 16 bits */
- .word 0xfffece14
-REG_ARM_SYSST: /* 16 bits */
- .word 0xfffece18
-/* DPLL control registers */
-REG_DPLL1_CTL: /* 16 bits */
- .word 0xfffecf00
-/* identification code register */
-REG_IDCODE: /* 32 bits */
- .word 0xfffed404
-
-/* Innovator specific */
-REG_FPGA_LED_DIGIT: /* 8 bits (not used on Innovator) */
- .word 0x08000003
-REG_FPGA_POWER: /* 8 bits */
- .word 0x08000005
-REG_FPGA_AUDIO: /* 8 bits (not used on Innovator) */
- .word 0x0800000c
-REG_FPGA_DIP_SWITCH: /* 8 bits (not used on Innovator) */
- .word 0x0800000e
-
-VAL_COMP_MODE_CTRL_0:
- .word 0x0000eaef
-VAL_FUNC_MUX_CTRL_4:
- .word 0x00000000
-VAL_FUNC_MUX_CTRL_5:
- .word 0x00000000
-VAL_FUNC_MUX_CTRL_6:
- .word 0x00000001
-VAL_FUNC_MUX_CTRL_7:
- .word 0x00000000
-VAL_FUNC_MUX_CTRL_8:
- .word 0x10001200
-VAL_FUNC_MUX_CTRL_9:
- .word 0x01201012
-VAL_FUNC_MUX_CTRL_A:
- .word 0x00000248
-VAL_FUNC_MUX_CTRL_B:
- .word 0x00000248
-VAL_FUNC_MUX_CTRL_C:
- .word 0x09000000
-VAL_FUNC_MUX_CTRL_D:
- .word 0x00000000
-VAL_PULL_DWN_CTRL_0:
- .word 0x11a10000
-VAL_PULL_DWN_CTRL_1:
- .word 0x2e047fff
-VAL_PULL_DWN_CTRL_2:
- .word 0xffd603a6
-VAL_PULL_DWN_CTRL_3:
- .word 0x00003e03
-VAL_VOLTAGE_CTRL_0:
- .word 0x00000007
-VAL_TEST_DBG_CTRL_0:
- /* See Errata 4.13, This works around a SRAM bug, for chips below ES2.5 .
- * This slows down internal SRAM accesses.
- */
- .word 0x00000007
-VAL_MOD_CONF_CTRL_0:
- .word 0x0b000008
-VAL_ARM_CKCTL:
- .word 0x010f
-VAL_DPLL1_CTL:
- .word 0x2710
-VAL_TC_EMIFS_CS1_CONFIG_PRELIM:
- .word 0x00001149
-VAL_TC_EMIFS_CS2_CONFIG_PRELIM:
- .word 0x00004158
-VAL_TC_EMIFS_CS0_CONFIG:
- .word 0x002130b0
-VAL_TC_EMIFS_CS1_CONFIG:
- .word 0x0000f559
-VAL_TC_EMIFS_CS2_CONFIG:
- .word 0x000055f0
-VAL_TC_EMIFS_CS3_CONFIG:
- .word 0x00003331
-VAL_TC_EMIFF_SDRAM_CONFIG:
- .word 0x010290fc
-VAL_TC_EMIFF_MRS:
- .word 0x00000027
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2002
- * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static void flash__init (void);
-static void ether__init (void);
-
-static inline void delay (unsigned long loops)
-{
- __asm__ volatile ("1:\n"
- "subs %0, %1, #1\n"
- "bne 1b":"=r" (loops):"0" (loops));
-}
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-
-int board_init (void)
-{
- /* arch number of OMAP 1510-Board */
- gd->bd->bi_arch_number = MACH_TYPE_OMAP_INNOVATOR;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = 0x10000100;
-
-/* kk - this speeds up your boot a quite a bit. However to make it
- * work, you need make sure your kernel startup flush bug is fixed.
- * ... rkw ...
- */
- icache_enable ();
-
- flash__init ();
- ether__init ();
- return 0;
-}
-
-
-int misc_init_r (void)
-{
- /* volatile ushort *gdir = (ushort *) (GPIO_DIR_CONTROL_REG); */
- /* volatile ushort *mdir = (ushort *) (MPUIO_DIR_CONTROL_REG); */
-
- /* setup gpio direction to match board (no floats!) */
- /**gdir = 0xCFF9; */
- /**mdir = 0x103F; */
-
- return (0);
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-static void flash__init (void)
-{
-#define CS0_CHIP_SELECT_REG 0xfffecc10
-#define CS3_CHIP_SELECT_REG 0xfffecc1c
-#define EMIFS_GlB_Config_REG 0xfffecc0c
-
- {
- unsigned int regval;
-
- regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG);
- regval = regval | 0x0001; /* Turn off write protection for flash devices. */
- if (regval & 0x0002) {
- regval = regval & 0xfffd; /* Swap CS0 and CS3 so that flash is visible at 0x0 and eeprom at 0x0c000000. */
- /* If, instead, you want to reference flash at 0x0c000000, then it seemed the following were necessary. */
- /* *((volatile unsigned int *)CS0_CHIP_SELECT_REG) = 0x202090; / * Overrides head.S setting of 0x212090 */
- /* *((volatile unsigned int *)CS3_CHIP_SELECT_REG) = 0x202090; / * Let's flash chips be fully functional. */
- }
- *((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval;
- }
-}
-
-
-/******************************
- Routine:
- Description:
-******************************/
-static void ether__init (void)
-{
-#define ETH_CONTROL_REG 0x0800000b
- /* take the Ethernet controller out of reset and wait
- * for the EEPROM load to complete.
- */
- *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
- udelay (3);
-}
-
-
-int dram_init (void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
- return 0;
-}
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = $(obj)lib$(BOARD).a
-
-COBJS := omap1610innovator.o flash.o
-SOBJS := lowlevel_init.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-$(LIB): $(obj).depend $(OBJS) $(SOBJS)
- $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
-
-clean:
- rm -f $(SOBJS) $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
+++ /dev/null
-#
-# (C) Copyright 2002
-# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
-# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
-#
-# (C) Copyright 2003
-# Texas Instruments, <www.ti.com>
-# Kshitij Gupta <Kshitij@ti.com>
-#
-# TI Innovator board with OMAP1610 (ARM925EJS) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# Innovator has 1 bank of 256 MB SDRAM
-# Physical Address:
-# 1000'0000 to 2000'0000
-#
-#
-# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000
-# (mem base + reserved)
-#
-# we load ourself to 1108'0000
-#
-#
-
-
-TEXT_BASE = 0x11080000
+++ /dev/null
-/*
- * (C) Copyright 2001
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2001-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <linux/byteorder/swab.h>
-
-#define PHYS_FLASH_SECT_SIZE 0x00020000 /* 256 KB sectors (x2) */
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-/* Board support for 1 or 2 flash devices */
-#undef FLASH_PORT_WIDTH32
-#define FLASH_PORT_WIDTH16
-
-#ifdef FLASH_PORT_WIDTH16
-#define FLASH_PORT_WIDTH ushort
-#define FLASH_PORT_WIDTHV vu_short
-#define SWAP(x) __swab16(x)
-#else
-#define FLASH_PORT_WIDTH ulong
-#define FLASH_PORT_WIDTHV vu_long
-#define SWAP(x) __swab32(x)
-#endif
-
-#define FPW FLASH_PORT_WIDTH
-#define FPWV FLASH_PORT_WIDTHV
-
-#define mb() __asm__ __volatile__ ("" : : : "memory")
-
-
-/* Flash Organization Structure */
-typedef struct OrgDef {
- unsigned int sector_number;
- unsigned int sector_size;
-} OrgDef;
-
-
-/* Flash Organizations */
-OrgDef OrgIntel_28F256L18T[] = {
- {4, 32 * 1024}, /* 4 * 32kBytes sectors */
- {255, 128 * 1024}, /* 255 * 128kBytes sectors */
-};
-
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-unsigned long flash_init (void);
-static ulong flash_get_size (FPW * addr, flash_info_t * info);
-static int write_data (flash_info_t * info, ulong dest, FPW data);
-static void flash_get_offsets (ulong base, flash_info_t * info);
-void inline spin_wheel (void);
-void flash_print_info (flash_info_t * info);
-void flash_unprotect_sectors (FPWV * addr);
-int flash_erase (flash_info_t * info, int s_first, int s_last);
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt);
-void flash_unlock(flash_info_t * info);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- int i;
- ulong size = 0;
-
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
- switch (i) {
- case 0:
- flash_get_size ((FPW *) CONFIG_SYS_FLASH_BASE, &flash_info[i]);
- flash_get_offsets (CONFIG_SYS_FLASH_BASE, &flash_info[i]);
- /* to reset the lock bit */
- flash_unlock(&flash_info[i]);
- break;
- default:
- panic ("configured too many flash banks!\n");
- break;
- }
- size += flash_info[i].size;
- }
-
- /* Protect monitor and environment sectors
- */
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_SYS_FLASH_BASE,
- CONFIG_SYS_FLASH_BASE + monitor_flash_len - 1, &flash_info[0]);
-
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]);
-
- return size;
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_unlock(flash_info_t * info)
-{
- int j;
- for (j=2;j<CONFIG_SYS_MAX_FLASH_SECT;j++){
- FPWV *addr = (FPWV *) (info->start[j]);
- flash_unprotect_sectors (addr);
- *addr = (FPW) 0x00500050;/* clear status register */
- *addr = (FPW) 0x00FF00FF;/* resest to read mode */
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t * info)
-{
- int i;
- OrgDef *pOrgDef;
-
- pOrgDef = OrgIntel_28F256L18T;
- if (info->flash_id == FLASH_UNKNOWN) {
- return;
- }
-
- if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
- for (i = 0; i < info->sector_count; i++) {
- if (i > 255) {
- info->start[i] = base + (i * 0x8000);
- info->protect[i] = 0;
- } else {
- info->start[i] = base +
- (i * PHYS_FLASH_SECT_SIZE);
- info->protect[i] = 0;
- }
- }
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_INTEL:
- printf ("INTEL ");
- break;
- default:
- printf ("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_28F256L18T:
- printf ("FLASH 28F256L18T\n");
- break;
- default:
- printf ("Unknown Chip Type\n");
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i], info->protect[i] ? " (RO)" : " ");
- }
- printf ("\n");
- return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (FPW * addr, flash_info_t * info)
-{
- volatile FPW value;
-
- /* Write auto select command: read Manufacturer ID */
- addr[0x5555] = (FPW) 0x00AA00AA;
- addr[0x2AAA] = (FPW) 0x00550055;
- addr[0x5555] = (FPW) 0x00900090;
-
- mb ();
- value = addr[0];
-
- switch (value) {
-
- case (FPW) INTEL_MANUFACT:
- info->flash_id = FLASH_MAN_INTEL;
- break;
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- addr[0] = (FPW) 0x00FF00FF; /* restore read mode */
- return (0); /* no or unknown flash */
- }
-
- mb ();
- value = addr[1]; /* device ID */
- switch (value) {
-
- case (FPW) (INTEL_ID_28F256L18T):
- info->flash_id += FLASH_28F256L18T;
- info->sector_count = 259;
- info->size = 0x02000000;
- break; /* => 32 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- break;
- }
-
- if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
- printf ("** ERROR: sector count %d > max (%d) **\n",
- info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
- info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
- }
-
- addr[0] = (FPW) 0x00FF00FF; /* restore read mode */
-
- return (info->size);
-}
-
-
-/* unprotects a sector for write and erase
- * on some intel parts, this unprotects the entire chip, but it
- * wont hurt to call this additional times per sector...
- */
-void flash_unprotect_sectors (FPWV * addr)
-{
-#define PD_FINTEL_WSMS_READY_MASK 0x0080
-
- *addr = (FPW) 0x00500050; /* clear status register */
-
- /* this sends the clear lock bit command */
- *addr = (FPW) 0x00600060;
- *addr = (FPW) 0x00D000D0;
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
- int flag, prot, sect;
- ulong type, start, last;
- int rcode = 0;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- type = (info->flash_id & FLASH_VENDMASK);
- if ((type != FLASH_MAN_INTEL)) {
- printf ("Can't erase unknown flash type %08lx - aborted\n",
- info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
-
- start = get_timer (0);
- last = start;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- FPWV *addr = (FPWV *) (info->start[sect]);
- FPW status;
-
- printf ("Erasing sector %2d ... ", sect);
-
- flash_unprotect_sectors (addr);
-
- /* arm simple, non interrupt dependent timer */
- reset_timer_masked ();
-
- *addr = (FPW) 0x00500050;/* clear status register */
- *addr = (FPW) 0x00200020;/* erase setup */
- *addr = (FPW) 0x00D000D0;/* erase confirm */
-
- while (((status =
- *addr) & (FPW) 0x00800080) !=
- (FPW) 0x00800080) {
- if (get_timer_masked () >
- CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- /* suspend erase */
- *addr = (FPW) 0x00B000B0;
- /* reset to read mode */
- *addr = (FPW) 0x00FF00FF;
- rcode = 1;
- break;
- }
- }
-
- /* clear status register cmd. */
- *addr = (FPW) 0x00500050;
- *addr = (FPW) 0x00FF00FF;/* resest to read mode */
- printf (" done\n");
- }
- }
- return rcode;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- ulong cp, wp;
- FPW data;
- int count, i, l, rc, port_width;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return 4;
- }
-/* get lower word aligned address */
-#ifdef FLASH_PORT_WIDTH16
- wp = (addr & ~1);
- port_width = 2;
-#else
- wp = (addr & ~3);
- port_width = 4;
-#endif
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i = 0, cp = wp; i < l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
- for (; i < port_width && cnt > 0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt == 0 && i < port_width; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- if ((rc = write_data (info, wp, SWAP (data))) != 0) {
- return (rc);
- }
- wp += port_width;
- }
-
- /*
- * handle word aligned part
- */
- count = 0;
- while (cnt >= port_width) {
- data = 0;
- for (i = 0; i < port_width; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_data (info, wp, SWAP (data))) != 0) {
- return (rc);
- }
- wp += port_width;
- cnt -= port_width;
- if (count++ > 0x800) {
- spin_wheel ();
- count = 0;
- }
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i < port_width; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- return (write_data (info, wp, SWAP (data)));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word or halfword to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t * info, ulong dest, FPW data)
-{
- FPWV *addr = (FPWV *) dest;
- ulong status;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*addr & data) != data) {
- printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr);
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
- *addr = (FPW) 0x00400040; /* write setup */
- *addr = data;
-
- /* arm simple, non interrupt dependent timer */
- reset_timer_masked ();
-
- /* wait while polling the status register */
- while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
- if (get_timer_masked () > CONFIG_SYS_FLASH_WRITE_TOUT) {
- *addr = (FPW) 0x00FF00FF; /* restore read mode */
- return (1);
- }
- }
- *addr = (FPW) 0x00FF00FF; /* restore read mode */
- return (0);
-}
-
-void inline spin_wheel (void)
-{
- static int p = 0;
- static char w[] = "\\/-";
-
- printf ("\010%c", w[p]);
- (++p == 3) ? (p = 0) : 0;
-}
+++ /dev/null
-/*
- * Board specific setup info
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-
-#if defined(CONFIG_OMAP1610)
-#include <./configs/omap1510.h>
-#endif
-
-
-_TEXT_BASE:
- .word TEXT_BASE /* sdram load addr from config.mk */
-
-.globl lowlevel_init
-lowlevel_init:
-
-
- /*------------------------------------------------------*
- *mask all IRQs by setting all bits in the INTMR default*
- *------------------------------------------------------*/
- mov r1, #0xffffffff
- ldr r0, =REG_IHL1_MIR
- str r1, [r0]
- ldr r0, =REG_IHL2_MIR
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT1) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT1
- ldr r1, VAL_ARM_IDLECT1
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT2) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT2
- ldr r1, VAL_ARM_IDLECT2
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT3) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT3
- ldr r1, VAL_ARM_IDLECT3
- str r1, [r0]
-
-#ifdef CONFIG_CS_AUTOBOOT /* do the setup depending on boot mode */
- ldr r0, CONF_STATUS
- ldr r1, [r0]
- tst r1, #0x02
- beq disable_wd /* booting from RAM, skip setup */
-#endif
-
- mov r1, #0x01 /* PER_EN bit */
- ldr r0, REG_ARM_RSTCT2
- strh r1, [r0] /* CLKM; Peripheral reset. */
-
- /* Set CLKM to Sync-Scalable */
- /* I supposedly need to enable the dsp clock before switching */
- mov r1, #0x0000
- ldr r0, REG_ARM_SYSST
- strh r1, [r0]
- mov r0, #0x400
-1:
- subs r0, r0, #0x1 /* wait for any bubbles to finish */
- bne 1b
- ldr r1, VAL_ARM_CKCTL
- ldr r0, REG_ARM_CKCTL
- strh r1, [r0]
-
- /* a few nops to let settle */
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
-
- /* setup DPLL 1 */
- /* Ramp up the clock to 96Mhz */
- ldr r1, VAL_DPLL1_CTL
- ldr r0, REG_DPLL1_CTL
- strh r1, [r0]
- ands r1, r1, #0x10 /* Check if PLL is enabled. */
- beq lock_end /* Do not look for lock if BYPASS selected */
-2:
- ldrh r1, [r0]
- ands r1, r1, #0x01 /* Check the LOCK bit.*/
- beq 2b /* loop until bit goes hi. */
-lock_end:
-
-
- /*------------------------------------------------------*
- * Turn off the watchdog during init... *
- *------------------------------------------------------*/
-disable_wd:
- ldr r0, REG_WATCHDOG
- ldr r1, WATCHDOG_VAL1
- str r1, [r0]
- ldr r1, WATCHDOG_VAL2
- str r1, [r0]
- ldr r0, REG_WSPRDOG
- ldr r1, WSPRDOG_VAL1
- str r1, [r0]
- ldr r0, REG_WWPSDOG
-
-watch1Wait:
- ldr r1, [r0]
- tst r1, #0x10
- bne watch1Wait
-
- ldr r0, REG_WSPRDOG
- ldr r1, WSPRDOG_VAL2
- str r1, [r0]
- ldr r0, REG_WWPSDOG
-watch2Wait:
- ldr r1, [r0]
- tst r1, #0x10
- bne watch2Wait
-
-
- /* Set memory timings corresponding to the new clock speed */
-
- /* Check execution location to determine current execution location
- * and branch to appropriate initialization code.
- */
- /* Load physical SDRAM base. */
- mov r0, #0x10000000
- /* Get current execution location. */
- mov r1, pc
- /* Compare. */
- cmp r1, r0
- /* Skip over EMIF-fast initialization if running from SDRAM. */
- bge skip_sdram
-
- /*
- * Delay for SDRAM initialization.
- */
- mov r3, #0x1800 /* value should be checked */
-3:
- subs r3, r3, #0x1 /* Decrement count */
- bne 3b
-
-
- /*
- * Set SDRAM control values. Disable refresh before MRS command.
- */
-
- /* mobile ddr operation */
- ldr r0, REG_SDRAM_OPERATION
- mov r2, #07
- str r2, [r0]
-
- /* config register */
- ldr r0, REG_SDRAM_CONFIG
- ldr r1, SDRAM_CONFIG_VAL
- str r1, [r0]
-
- /* manual command register */
- ldr r0, REG_SDRAM_MANUAL_CMD
- /* issue set cke high */
- mov r1, #CMD_SDRAM_CKE_SET_HIGH
- str r1, [r0]
- /* issue nop */
- mov r1, #CMD_SDRAM_NOP
- str r1, [r0]
-
- mov r2, #0x0100
-waitMDDR1:
- subs r2, r2, #1
- bne waitMDDR1 /* delay loop */
-
- /* issue precharge */
- mov r1, #CMD_SDRAM_PRECHARGE
- str r1, [r0]
-
- /* issue autorefresh x 2 */
- mov r1, #CMD_SDRAM_AUTOREFRESH
- str r1, [r0]
- str r1, [r0]
-
- /* mrs register ddr mobile */
- ldr r0, REG_SDRAM_MRS
- mov r1, #0x33
- str r1, [r0]
-
- /* emrs1 low-power register */
- ldr r0, REG_SDRAM_EMRS1
- /* self refresh on all banks */
- mov r1, #0
- str r1, [r0]
-
- ldr r0, REG_DLL_URD_CONTROL
- ldr r1, DLL_URD_CONTROL_VAL
- str r1, [r0]
-
- ldr r0, REG_DLL_LRD_CONTROL
- ldr r1, DLL_LRD_CONTROL_VAL
- str r1, [r0]
-
- ldr r0, REG_DLL_WRT_CONTROL
- ldr r1, DLL_WRT_CONTROL_VAL
- str r1, [r0]
-
- /* delay loop */
- mov r2, #0x0100
-waitMDDR2:
- subs r2, r2, #1
- bne waitMDDR2
-
- /*
- * Delay for SDRAM initialization.
- */
- mov r3, #0x1800
-4:
- subs r3, r3, #1 /* Decrement count. */
- bne 4b
- b common_tc
-
-skip_sdram:
-
- ldr r0, REG_SDRAM_CONFIG
- ldr r1, SDRAM_CONFIG_VAL
- str r1, [r0]
-
-common_tc:
- /* slow interface */
- ldr r1, VAL_TC_EMIFS_CS0_CONFIG
- ldr r0, REG_TC_EMIFS_CS0_CONFIG
- str r1, [r0] /* Chip Select 0 */
-
- ldr r1, VAL_TC_EMIFS_CS1_CONFIG
- ldr r0, REG_TC_EMIFS_CS1_CONFIG
- str r1, [r0] /* Chip Select 1 */
- ldr r1, VAL_TC_EMIFS_CS3_CONFIG
- ldr r0, REG_TC_EMIFS_CS3_CONFIG
- str r1, [r0] /* Chip Select 3 */
-
-#ifdef CONFIG_H2_OMAP1610
- /* inserting additional 2 clock cycle hold time for LAN */
- ldr r0, REG_TC_EMIFS_CS1_ADVANCED
- ldr r1, VAL_TC_EMIFS_CS1_ADVANCED
- str r1, [r0]
-#endif
- /* Start MPU Timer 1 */
- ldr r0, REG_MPU_LOAD_TIMER
- ldr r1, VAL_MPU_LOAD_TIMER
- str r1, [r0]
-
- ldr r0, REG_MPU_CNTL_TIMER
- ldr r1, VAL_MPU_CNTL_TIMER
- str r1, [r0]
-
- /* back to arch calling code */
- mov pc, lr
-
- /* the literal pools origin */
- .ltorg
-
-#ifdef CONFIG_CS_AUTOBOOT
-CONF_STATUS:
- .word 0xfffe1130 /* 32 bits */
-#endif
-
-REG_TC_EMIFS_CONFIG: /* 32 bits */
- .word 0xfffecc0c
-REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */
- .word 0xfffecc10
-REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */
- .word 0xfffecc14
-REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */
- .word 0xfffecc18
-REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */
- .word 0xfffecc1c
-
-#ifdef CONFIG_H2_OMAP1610
-REG_TC_EMIFS_CS1_ADVANCED: /* 32 bits */
- .word 0xfffecc54
-#endif
-
-/* MPU clock/reset/power mode control registers */
-REG_ARM_CKCTL: /* 16 bits */
- .word 0xfffece00
-
-REG_ARM_IDLECT3: /* 16 bits */
- .word 0xfffece24
-REG_ARM_IDLECT2: /* 16 bits */
- .word 0xfffece08
-REG_ARM_IDLECT1: /* 16 bits */
- .word 0xfffece04
-
-REG_ARM_RSTCT2: /* 16 bits */
- .word 0xfffece14
-REG_ARM_SYSST: /* 16 bits */
- .word 0xfffece18
-/* DPLL control registers */
-REG_DPLL1_CTL: /* 16 bits */
- .word 0xfffecf00
-
-/* Watch Dog register */
-/* secure watchdog stop */
-REG_WSPRDOG:
- .word 0xfffeb048
-/* watchdog write pending */
-REG_WWPSDOG:
- .word 0xfffeb034
-
-WSPRDOG_VAL1:
- .word 0x0000aaaa
-WSPRDOG_VAL2:
- .word 0x00005555
-
-/* SDRAM config is: auto refresh enabled, 16 bit 4 bank,
- counter @8192 rows, 10 ns, 8 burst */
-REG_SDRAM_CONFIG:
- .word 0xfffecc20
-
-/* Operation register */
-REG_SDRAM_OPERATION:
- .word 0xfffecc80
-
-/* Manual command register */
-REG_SDRAM_MANUAL_CMD:
- .word 0xfffecc84
-
-/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */
-REG_SDRAM_MRS:
- .word 0xfffecc70
-
-/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */
-REG_SDRAM_EMRS1:
- .word 0xfffecc78
-
-/* WRT DLL register */
-REG_DLL_WRT_CONTROL:
- .word 0xfffecc68
-DLL_WRT_CONTROL_VAL:
- .word 0x03f00002
-
-/* URD DLL register */
-REG_DLL_URD_CONTROL:
- .word 0xfffeccc0
-DLL_URD_CONTROL_VAL:
- .word 0x00800002
-
-/* LRD DLL register */
-REG_DLL_LRD_CONTROL:
- .word 0xfffecccc
-
-REG_WATCHDOG:
- .word 0xfffec808
-
-REG_MPU_LOAD_TIMER:
- .word 0xfffec504
-REG_MPU_CNTL_TIMER:
- .word 0xfffec500
-
-/* 96 MHz Samsung Mobile DDR */
-SDRAM_CONFIG_VAL:
- .word 0x001200f4
-
-DLL_LRD_CONTROL_VAL:
- .word 0x00800002
-
-VAL_ARM_CKCTL:
- .word 0x3000
-VAL_DPLL1_CTL:
- .word 0x2830
-
-#ifdef CONFIG_INNOVATOROMAP1610
-VAL_TC_EMIFS_CS0_CONFIG:
- .word 0x002130b0
-VAL_TC_EMIFS_CS1_CONFIG:
- .word 0x00001131
-VAL_TC_EMIFS_CS2_CONFIG:
- .word 0x000055f0
-VAL_TC_EMIFS_CS3_CONFIG:
- .word 0x88011131
-#endif
-
-#ifdef CONFIG_H2_OMAP1610
-VAL_TC_EMIFS_CS0_CONFIG:
- .word 0x00203331
-VAL_TC_EMIFS_CS1_CONFIG:
- .word 0x8180fff3
-VAL_TC_EMIFS_CS2_CONFIG:
- .word 0xf800f22a
-VAL_TC_EMIFS_CS3_CONFIG:
- .word 0x88011131
-VAL_TC_EMIFS_CS1_ADVANCED:
- .word 0x00000022
-#endif
-
-VAL_TC_EMIFF_SDRAM_CONFIG:
- .word 0x010290fc
-VAL_TC_EMIFF_MRS:
- .word 0x00000027
-
-VAL_ARM_IDLECT1:
- .word 0x00000400
-
-VAL_ARM_IDLECT2:
- .word 0x00000886
-VAL_ARM_IDLECT3:
- .word 0x00000015
-
-WATCHDOG_VAL1:
- .word 0x000000f5
-WATCHDOG_VAL2:
- .word 0x000000a0
-
-VAL_MPU_LOAD_TIMER:
- .word 0xffffffff
-VAL_MPU_CNTL_TIMER:
- .word 0xffffffa1
-
-/* command values */
-.equ CMD_SDRAM_NOP, 0x00000000
-.equ CMD_SDRAM_PRECHARGE, 0x00000001
-.equ CMD_SDRAM_AUTOREFRESH, 0x00000002
-.equ CMD_SDRAM_CKE_SET_HIGH, 0x00000007
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2002
- * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#if defined(CONFIG_OMAP1610)
-#include <./configs/omap1510.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_CS_AUTOBOOT
-unsigned long omap_flash_base;
-#endif
-
-void flash__init (void);
-void ether__init (void);
-void set_muxconf_regs (void);
-void peripheral_power_enable (void);
-
-#define COMP_MODE_ENABLE ((unsigned int)0x0000EAEF)
-
-static inline void delay (unsigned long loops)
-{
- __asm__ volatile ("1:\n"
- "subs %0, %1, #1\n"
- "bne 1b":"=r" (loops):"0" (loops));
-}
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-
-int board_init (void)
-{
- if (machine_is_omap_h2())
- gd->bd->bi_arch_number = MACH_TYPE_OMAP_H2;
- else if (machine_is_omap_innovator())
- gd->bd->bi_arch_number = MACH_TYPE_OMAP_INNOVATOR;
- else
- gd->bd->bi_arch_number = MACH_TYPE_OMAP_GENERIC;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = 0x10000100;
-
- /* Configure MUX settings */
- set_muxconf_regs ();
- peripheral_power_enable ();
-
-/* this speeds up your boot a quite a bit. However to make it
- * work, you need make sure your kernel startup flush bug is fixed.
- * ... rkw ...
- */
- icache_enable ();
-
- flash__init ();
- ether__init ();
- return 0;
-}
-
-
-int misc_init_r (void)
-{
- /* currently empty */
- return (0);
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-void flash__init (void)
-{
-#define EMIFS_GlB_Config_REG 0xfffecc0c
- unsigned int regval;
-
-#ifdef CONFIG_CS_AUTOBOOT
- /* Check swapping of CS0 and CS3, set flash base accordingly */
- omap_flash_base = ((*((u32 *)OMAP_EMIFS_CONFIG_REG) & 0x02) == 0) ?
- PHYS_FLASH_1_BM0 : PHYS_FLASH_1_BM1;
-#endif
- regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG);
- /* Turn off write protection for flash devices. */
- regval = regval | 0x0001;
- *((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval;
-}
-/*************************************************************
- Routine:ether__init
- Description: take the Ethernet controller out of reset and wait
- for the EEPROM load to complete.
-*************************************************************/
-void ether__init (void)
-{
-#define ETH_CONTROL_REG 0x0400030b
-
-#ifdef CONFIG_H2_OMAP1610
- #define LAN_RESET_REGISTER 0x0400001c
-
- /* The debug board on which the lan chip resides may not be powered
- * ON at the same time as the OMAP chip. So wait in a loop until the
- * lan reset register (on the debug board) is available (powered on)
- * and reset the lan chip.
- */
-
- *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000;
- do {
- *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0001;
- udelay (3);
- } while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0001);
-
- do {
- *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000;
- udelay (3);
- } while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0000);
-#endif
-
- *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
- udelay (3);
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-int dram_init (void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
- return 0;
-}
-
-/******************************************************
- Routine: set_muxconf_regs
- Description: Setting up the configuration Mux registers
- specific to the hardware
-*******************************************************/
-void set_muxconf_regs (void)
-{
- volatile unsigned int *MuxConfReg;
- /* set each registers to its reset value; */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
- /* setup for UART1 */
- *MuxConfReg &= ~(0x02000000); /* bit 25 */
- /* setup for UART2 */
- *MuxConfReg &= ~(0x01000000); /* bit 24 */
- /* Disable Uwire CS Hi-Z */
- *MuxConfReg |= 0x08000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_3);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_4);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_5);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_6);
- /*setup mux for UART3 */
- *MuxConfReg |= 0x00000001; /* bit3, 1, 0 (mux0 5,5,26) */
- *MuxConfReg &= ~0x0000003e;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_7);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_8);
- /* Disable Uwire CS Hi-Z */
- *MuxConfReg |= 0x00001200; /*bit 9 for CS0 12 for CS3 */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_9);
- /* Need to turn on bits 21 and 12 in FUNC_MUX_CTRL_9 so the */
- /* hardware will actually use TX and RTS based on bit 25 in */
- /* FUNC_MUX_CTRL_0. I told you this thing was screwy! */
- *MuxConfReg |= 0x00201000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_A);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_B);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_C);
- /* setup for UART2 */
- /* Need to turn on bits 27 and 24 in FUNC_MUX_CTRL_C so the */
- /* hardware will actually use TX and RTS based on bit 24 in */
- /* FUNC_MUX_CTRL_0. */
- *MuxConfReg |= 0x09000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_0);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_1);
- *MuxConfReg = 0x00000000;
- /* mux setup for SD/MMC driver */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_2);
- *MuxConfReg &= 0xFFFE0FFF;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_3);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
- /* bit 13 for MMC2 XOR_CLK */
- *MuxConfReg &= ~(0x00002000);
- /* bit 29 for UART 1 */
- *MuxConfReg &= ~(0x00002000);
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
- /* Configure for USB. Turn on VBUS_CTRL and VBUS_MODE. */
- *MuxConfReg |= 0x000C0000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int)USB_TRANSCEIVER_CTRL);
- *MuxConfReg &= ~(0x00000070);
- *MuxConfReg &= ~(0x00000008);
- *MuxConfReg |= 0x00000003;
- *MuxConfReg |= 0x00000180;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
- /* bit 17, software controls VBUS */
- *MuxConfReg &= ~(0x00020000);
- /* Enable USB 48 and 12M clocks */
- *MuxConfReg |= 0x00000200;
- *MuxConfReg &= ~(0x00000180);
- /*2.75V for MMCSDIO1 */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) VOLTAGE_CTRL_0);
- *MuxConfReg = 0x00001FE7;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_0);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_1);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_3);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_4);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_4);
- *MuxConfReg = 0x00000000;
- /* Turn on UART2 48 MHZ clock */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
- *MuxConfReg |= 0x40000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) USB_OTG_CTRL);
- /* setup for USB VBus detection OMAP161x */
- *MuxConfReg |= 0x00040000; /* bit 18 */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
- /* PullUps for SD/MMC driver */
- *MuxConfReg |= ~(0xFFFE0FFF);
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int)COMP_MODE_CTRL_0);
- *MuxConfReg = COMP_MODE_ENABLE;
-}
-
-/******************************************************
- Routine: peripheral_power_enable
- Description: Enable the power for UART1
-*******************************************************/
-void peripheral_power_enable (void)
-{
-#define UART1_48MHZ_ENABLE ((unsigned short)0x0200)
-#define SW_CLOCK_REQUEST ((volatile unsigned short *)0xFFFE0834)
-
- *SW_CLOCK_REQUEST |= UART1_48MHZ_ENABLE;
-}
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = $(obj)lib$(BOARD).a
-
-COBJS := omap2420h4.o mem.o sys_info.o
-SOBJS := lowlevel_init.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-$(LIB): $(obj).depend $(OBJS) $(SOBJS)
- $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
-
-clean:
- rm -f $(SOBJS) $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
+++ /dev/null
-#
-# (C) Copyright 2004
-# Texas Instruments, <www.ti.com>
-#
-# TI H4 board with OMAP2420 (ARM1136) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# H4 has 1 bank of 32MB or 64MB mDDR-SDRAM on CS0
-# H4 has 1 bank of 32MB or 00MB mDDR-SDRAM on CS1
-# Physical Address:
-# 8000'0000 (bank0)
-# A000/0000 (bank1) ES2 will be configurable
-# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
-# (mem base + reserved)
-
-# For use with external or internal boots.
-TEXT_BASE = 0x80e80000
-
-# Used with full SRAM boot.
-# This is either with a GP system or a signed boot image.
-# easiest, and safest way to go if you can.
-#TEXT_BASE = 0x40270000
-
-
-# Handy to get symbols to debug ROM version.
-#TEXT_BASE = 0x0
-#TEXT_BASE = 0x08000000
-#TEXT_BASE = 0x04000000
+++ /dev/null
-/*
- * Board specific setup info
- *
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Richard Woodruff <r-woodruff2@ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/omap2420.h>
-#include <asm/arch/mem.h>
-#include <asm/arch/clocks.h>
-
-_TEXT_BASE:
- .word TEXT_BASE /* sdram load addr from config.mk */
-
-/**************************************************************************
- * cpy_clk_code: relocates clock code into SRAM where its safer to execute
- * R1 = SRAM destination address.
- *************************************************************************/
-.global cpy_clk_code
- cpy_clk_code:
- /* Copy DPLL code into SRAM */
- adr r0, go_to_speed /* get addr of clock setting code */
- mov r2, #384 /* r2 size to copy (div by 32 bytes) */
- mov r1, r1 /* r1 <- dest address (passed in) */
- add r2, r2, r0 /* r2 <- source end address */
-next2:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- bne next2
- mov pc, lr /* back to caller */
-
-/* ****************************************************************************
- * go_to_speed: -Moves to bypass, -Commits clock dividers, -puts dpll at speed
- * -executed from SRAM.
- * R0 = PRCM_CLKCFG_CTRL - addr of valid reg
- * R1 = CM_CLKEN_PLL - addr dpll ctlr reg
- * R2 = dpll value
- * R3 = CM_IDLEST_CKGEN - addr dpll lock wait
- ******************************************************************************/
-.global go_to_speed
- go_to_speed:
- sub sp, sp, #0x4 /* get some stack space */
- str r4, [sp] /* save r4's value */
-
- /* move into fast relock bypass */
- ldr r8, pll_ctl_add
- mov r4, #0x2
- str r4, [r8]
- ldr r4, pll_stat
-block:
- ldr r8, [r4] /* wait for bypass to take effect */
- and r8, r8, #0x3
- cmp r8, #0x1
- bne block
-
- /* set new dpll dividers _after_ in bypass */
- ldr r4, pll_div_add
- ldr r8, pll_div_val
- str r8, [r4]
-
- /* now prepare GPMC (flash) for new dpll speed */
- /* flash needs to be stable when we jump back to it */
- ldr r4, cfg3_0_addr
- ldr r8, cfg3_0_val
- str r8, [r4]
- ldr r4, cfg4_0_addr
- ldr r8, cfg4_0_val
- str r8, [r4]
- ldr r4, cfg1_0_addr
- ldr r8, [r4]
- orr r8, r8, #0x3 /* up gpmc divider */
- str r8, [r4]
-
- /* setup to 2x loop though code. The first loop pre-loads the
- * icache, the 2nd commits the prcm config, and locks the dpll
- */
- mov r4, #0x1000 /* spin spin spin */
- mov r8, #0x4 /* first pass condition & set registers */
- cmp r8, #0x4
-2:
- ldrne r8, [r3] /* DPLL lock check */
- and r8, r8, #0x7
- cmp r8, #0x2
- beq 4f
-3:
- subeq r8, r8, #0x1
- streq r8, [r0] /* commit dividers (2nd time) */
- nop
-lloop1:
- sub r4, r4, #0x1 /* Loop currently necessary else bad jumps */
- nop
- cmp r4, #0x0
- bne lloop1
- mov r4, #0x40000
- cmp r8, #0x1
- nop
- streq r2, [r1] /* lock dpll (2nd time) */
- nop
-lloop2:
- sub r4, r4, #0x1 /* loop currently necessary else bad jumps */
- nop
- cmp r4, #0x0
- bne lloop2
- mov r4, #0x40000
- cmp r8, #0x1
- nop
- ldreq r8, [r3] /* get lock condition for dpll */
- cmp r8, #0x4 /* first time though? */
- bne 2b
- moveq r8, #0x2 /* set to dpll check condition. */
- beq 3b /* if condition not true branch */
-4:
- ldr r4, [sp]
- add sp, sp, #0x4 /* return stack space */
- mov pc, lr /* back to caller, locked */
-
-_go_to_speed: .word go_to_speed
-
-/* these constants need to be close for PIC code */
-cfg3_0_addr:
- .word GPMC_CONFIG3_0
-cfg3_0_val:
- .word H4_24XX_GPMC_CONFIG3_0
-cfg4_0_addr:
- .word GPMC_CONFIG4_0
-cfg4_0_val:
- .word H4_24XX_GPMC_CONFIG4_0
-cfg1_0_addr:
- .word GPMC_CONFIG1_0
-pll_ctl_add:
- .word CM_CLKEN_PLL
-pll_stat:
- .word CM_IDLEST_CKGEN
-pll_div_add:
- .word CM_CLKSEL1_PLL
-pll_div_val:
- .word DPLL_VAL /* DPLL setting (300MHz default) */
-
-.globl lowlevel_init
-lowlevel_init:
- ldr sp, SRAM_STACK
- str ip, [sp] /* stash old link register */
- mov ip, lr /* save link reg across call */
- bl s_init /* go setup pll,mux,memory */
- ldr ip, [sp] /* restore save ip */
- mov lr, ip /* restore link reg */
-
- /* map interrupt controller */
- ldr r0, VAL_INTH_SETUP
- mcr p15, 0, r0, c15, c2, 4
-
- /* back to arch calling code */
- mov pc, lr
-
- /* the literal pools origin */
- .ltorg
-
-REG_CONTROL_STATUS:
- .word CONTROL_STATUS
-VAL_INTH_SETUP:
- .word PERIFERAL_PORT_BASE
-SRAM_STACK:
- .word LOW_LEVEL_SRAM_STACK
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Richard Woodruff <r-woodruff2@ti.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/arch/omap2420.h>
-#include <asm/io.h>
-#include <asm/arch/bits.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/mem.h>
-#include <asm/arch/clocks.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/sys_info.h>
-
-/************************************************************
- * sdelay() - simple spin loop. Will be constant time as
- * its generally used in 12MHz bypass conditions only. This
- * is necessary until timers are accessible.
- *
- * not inline to increase chances its in cache when called
- *************************************************************/
-void sdelay (unsigned long loops)
-{
- __asm__ volatile ("1:\n" "subs %0, %1, #1\n"
- "bne 1b":"=r" (loops):"0" (loops));
-}
-
-/*********************************************************************************
- * prcm_init() - inits clocks for PRCM as defined in clocks.h (config II default).
- * -- called from SRAM, or Flash (using temp SRAM stack).
- *********************************************************************************/
-void prcm_init(void)
-{
- u32 div;
- void (*f_lock_pll) (u32, u32, u32, u32);
- extern void *_end_vect, *_start;
-
- f_lock_pll = (void *)((u32)&_end_vect - (u32)&_start + SRAM_VECT_CODE);
-
- __raw_writel(0, CM_FCLKEN1_CORE); /* stop all clocks to reduce ringing */
- __raw_writel(0, CM_FCLKEN2_CORE); /* may not be necessary */
- __raw_writel(0, CM_ICLKEN1_CORE);
- __raw_writel(0, CM_ICLKEN2_CORE);
-
- __raw_writel(DPLL_OUT, CM_CLKSEL2_PLL); /* set DPLL out */
- __raw_writel(MPU_DIV, CM_CLKSEL_MPU); /* set MPU divider */
- __raw_writel(DSP_DIV, CM_CLKSEL_DSP); /* set dsp and iva dividers */
- __raw_writel(GFX_DIV, CM_CLKSEL_GFX); /* set gfx dividers */
-
- div = BUS_DIV;
- __raw_writel(div, CM_CLKSEL1_CORE);/* set L3/L4/USB/Display/Vlnc/SSi dividers */
- sdelay(1000);
-
- if(running_in_sram()){
- /* If running fully from SRAM this is OK. The Flash bus drops out for just a little.
- * but then comes back. If running from Flash this sequence kills you, thus you need
- * to run it using CONFIG_PARTIAL_SRAM.
- */
- __raw_writel(MODE_BYPASS_FAST, CM_CLKEN_PLL); /* go to bypass, fast relock */
- wait_on_value(BIT0|BIT1, BIT0, CM_IDLEST_CKGEN, LDELAY); /* wait till in bypass */
- sdelay(1000);
- /* set clock selection and dpll dividers. */
- __raw_writel(DPLL_VAL, CM_CLKSEL1_PLL); /* set pll for target rate */
- __raw_writel(COMMIT_DIVIDERS, PRCM_CLKCFG_CTRL); /* commit dividers */
- sdelay(10000);
- __raw_writel(DPLL_LOCK, CM_CLKEN_PLL); /* enable dpll */
- sdelay(10000);
- wait_on_value(BIT0|BIT1, BIT1, CM_IDLEST_CKGEN, LDELAY); /*wait for dpll lock */
- }else if(running_in_flash()){
- /* if running from flash, need to jump to small relocated code area in SRAM.
- * This is the only safe spot to do configurations from.
- */
- (*f_lock_pll)(PRCM_CLKCFG_CTRL, CM_CLKEN_PLL, DPLL_LOCK, CM_IDLEST_CKGEN);
- }
-
- __raw_writel(DPLL_LOCK|APLL_LOCK, CM_CLKEN_PLL); /* enable apll */
- wait_on_value(BIT8, BIT8, CM_IDLEST_CKGEN, LDELAY); /* wait for apll lock */
- sdelay(1000);
-}
-
-/**************************************************************************
- * make_cs1_contiguous() - for es2 and above remap cs1 behind cs0 to allow
- * command line mem=xyz use all memory with out discontigious support
- * compiled in. Could do it at the ATAG, but there really is two banks...
- * Called as part of 2nd phase DDR init.
- **************************************************************************/
-void make_cs1_contiguous(void)
-{
- u32 size, a_add_low, a_add_high;
-
- size = get_sdr_cs_size(SDRC_CS0_OSET);
- size /= SZ_32M; /* find size to offset CS1 */
- a_add_high = (size & 3) << 8; /* set up low field */
- a_add_low = (size & 0x3C) >> 2; /* set up high field */
- __raw_writel((a_add_high|a_add_low),SDRC_CS_CFG);
-
-}
-
-/********************************************************
- * mem_ok() - test used to see if timings are correct
- * for a part. Helps in gussing which part
- * we are currently using.
- *******************************************************/
-u32 mem_ok(void)
-{
- u32 val1, val2;
- u32 pattern = 0x12345678;
-
- __raw_writel(0x0,OMAP2420_SDRC_CS0+0x400); /* clear pos A */
- __raw_writel(pattern, OMAP2420_SDRC_CS0); /* pattern to pos B */
- __raw_writel(0x0,OMAP2420_SDRC_CS0+4); /* remove pattern off the bus */
- val1 = __raw_readl(OMAP2420_SDRC_CS0+0x400); /* get pos A value */
- val2 = __raw_readl(OMAP2420_SDRC_CS0); /* get val2 */
-
- if ((val1 != 0) || (val2 != pattern)) /* see if pos A value changed*/
- return(0);
- else
- return(1);
-}
-
-
-/********************************************************
- * sdrc_init() - init the sdrc chip selects CS0 and CS1
- * - early init routines, called from flash or
- * SRAM.
- *******************************************************/
-void sdrc_init(void)
-{
- #define EARLY_INIT 1
- do_sdrc_init(SDRC_CS0_OSET, EARLY_INIT); /* only init up first bank here */
-}
-
-/*************************************************************************
- * do_sdrc_init(): initialize the SDRAM for use.
- * -called from low level code with stack only.
- * -code sets up SDRAM timing and muxing for 2422 or 2420.
- * -optimal settings can be placed here, or redone after i2c
- * inspection of board info
- *
- * This is a bit ugly, but should handle all memory moduels
- * used with the H4. The first time though this code from s_init()
- * we configure the first chip select. Later on we come back and
- * will configure the 2nd chip select if it exists.
- *
- **************************************************************************/
-void do_sdrc_init(u32 offset, u32 early)
-{
- u32 cpu, dllen=0, rev, common=0, cs0=0, pmask=0, pass_type, mtype;
- sdrc_data_t *sdata; /* do not change type */
- u32 a, b, r;
-
- static const sdrc_data_t sdrc_2422 =
- {
- H4_2422_SDRC_SHARING, H4_2422_SDRC_MDCFG_0_DDR, 0 , H4_2422_SDRC_ACTIM_CTRLA_0,
- H4_2422_SDRC_ACTIM_CTRLB_0, H4_2422_SDRC_RFR_CTRL, H4_2422_SDRC_MR_0_DDR,
- 0, H4_2422_SDRC_DLLAB_CTRL
- };
- static const sdrc_data_t sdrc_2420 =
- {
- H4_2420_SDRC_SHARING, H4_2420_SDRC_MDCFG_0_DDR, H4_2420_SDRC_MDCFG_0_SDR,
- H4_2420_SDRC_ACTIM_CTRLA_0, H4_2420_SDRC_ACTIM_CTRLB_0,
- H4_2420_SDRC_RFR_CTRL, H4_2420_SDRC_MR_0_DDR, H4_2420_SDRC_MR_0_SDR,
- H4_2420_SDRC_DLLAB_CTRL
- };
-
- if (offset == SDRC_CS0_OSET)
- cs0 = common = 1; /* int regs shared between both chip select */
-
- cpu = get_cpu_type();
- rev = get_cpu_rev();
-
- /* warning generated, though code generation is correct. this may bite later,
- * but is ok for now. there is only so much C code you can do on stack only
- * operation.
- */
- if (cpu == CPU_2422){
- sdata = (sdrc_data_t *)&sdrc_2422;
- pass_type = STACKED;
- } else{
- sdata = (sdrc_data_t *)&sdrc_2420;
- pass_type = IP_DDR;
- }
-
- __asm__ __volatile__("": : :"memory"); /* limit compiler scope */
-
- /* u-boot is compiled to run in DDR or SRAM at 8xxxxxxx or 4xxxxxxx.
- * If we are running in flash prior to relocation and we use data
- * here which is not pc relative we need to get the address correct.
- * We need to find the current flash mapping to dress up the initial
- * pointer load. As long as this is const data we should be ok.
- */
- if((early) && running_in_flash()){
- sdata = (sdrc_data_t *)(((u32)sdata & 0x0003FFFF) | get_gpmc0_base());
- /* NOR internal boot offset is 0x4000 from xloader signature */
- if(running_from_internal_boot())
- sdata = (sdrc_data_t *)((u32)sdata + 0x4000);
- }
-
- if (!early && (((mtype = get_mem_type()) == DDR_COMBO)||(mtype == DDR_STACKED))) {
- if(mtype == DDR_COMBO){
- pmask = BIT2;/* combo part has a shared CKE signal, can't use feature */
- pass_type = COMBO_DDR; /* CS1 config */
- __raw_writel((__raw_readl(SDRC_POWER)) & ~pmask, SDRC_POWER);
- }
- if(rev != CPU_2420_2422_ES1) /* for es2 and above smooth things out */
- make_cs1_contiguous();
- }
-
-next_mem_type:
- if (common) { /* do a SDRC reset between types to clear regs*/
- __raw_writel(SOFTRESET, SDRC_SYSCONFIG); /* reset sdrc */
- wait_on_value(BIT0, BIT0, SDRC_STATUS, 12000000);/* wait till reset done set */
- __raw_writel(0, SDRC_SYSCONFIG); /* clear soft reset */
- __raw_writel(sdata->sdrc_sharing, SDRC_SHARING);
-#ifdef POWER_SAVE
- __raw_writel(__raw_readl(SMS_SYSCONFIG)|SMART_IDLE, SMS_SYSCONFIG);
- __raw_writel(sdata->sdrc_sharing|SMART_IDLE, SDRC_SHARING);
- __raw_writel((__raw_readl(SDRC_POWER)|BIT6), SDRC_POWER);
-#endif
- }
-
- if ((pass_type == IP_DDR) || (pass_type == STACKED)) /* (IP ddr-CS0),(2422-CS0/CS1) */
- __raw_writel(sdata->sdrc_mdcfg_0_ddr, SDRC_MCFG_0+offset);
- else if (pass_type == COMBO_DDR){ /* (combo-CS0/CS1) */
- __raw_writel(H4_2420_COMBO_MDCFG_0_DDR,SDRC_MCFG_0+offset);
- } else if (pass_type == IP_SDR){ /* ip sdr-CS0 */
- __raw_writel(sdata->sdrc_mdcfg_0_sdr, SDRC_MCFG_0+offset);
- }
-
- a = sdata->sdrc_actim_ctrla_0;
- b = sdata->sdrc_actim_ctrlb_0;
- r = sdata->sdrc_dllab_ctrl;
-
- /* work around ES1 DDR issues */
- if((pass_type != IP_SDR) && (rev == CPU_2420_2422_ES1)){
- a = H4_242x_SDRC_ACTIM_CTRLA_0_ES1;
- b = H4_242x_SDRC_ACTIM_CTRLB_0_ES1;
- r = H4_242x_SDRC_RFR_CTRL_ES1;
- }
-
- if (cs0) {
- __raw_writel(a, SDRC_ACTIM_CTRLA_0);
- __raw_writel(b, SDRC_ACTIM_CTRLB_0);
- } else {
- __raw_writel(a, SDRC_ACTIM_CTRLA_1);
- __raw_writel(b, SDRC_ACTIM_CTRLB_1);
- }
- __raw_writel(r, SDRC_RFR_CTRL+offset);
-
- /* init sequence for mDDR/mSDR using manual commands (DDR is a bit different) */
- __raw_writel(CMD_NOP, SDRC_MANUAL_0+offset);
- sdelay(5000); /* susposed to be 100us per design spec for mddr/msdr */
- __raw_writel(CMD_PRECHARGE, SDRC_MANUAL_0+offset);
- __raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_0+offset);
- __raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_0+offset);
-
- /*
- * CSx SDRC Mode Register
- * Burst length = (4 - DDR) (2-SDR)
- * Serial mode
- * CAS latency = x
- */
- if(pass_type == IP_SDR)
- __raw_writel(sdata->sdrc_mr_0_sdr, SDRC_MR_0+offset);
- else
- __raw_writel(sdata->sdrc_mr_0_ddr, SDRC_MR_0+offset);
-
- /* NOTE: ES1 242x _BUG_ DLL + External Bandwidth fix*/
- if (rev == CPU_2420_2422_ES1){
- dllen = (BIT0|BIT3); /* es1 clear both bit0 and bit3 */
- __raw_writel((__raw_readl(SMS_CLASS_ARB0)|BURSTCOMPLETE_GROUP7)
- ,SMS_CLASS_ARB0);/* enable bust complete for lcd */
- }
- else
- dllen = BIT0|BIT1; /* es2, clear bit0, and 1 (set phase to 72) */
-
- /* enable & load up DLL with good value for 75MHz, and set phase to 90
- * ES1 recommends 90 phase, ES2 recommends 72 phase.
- */
- if (common && (pass_type != IP_SDR)) {
- __raw_writel(sdata->sdrc_dllab_ctrl, SDRC_DLLA_CTRL);
- __raw_writel(sdata->sdrc_dllab_ctrl & ~(BIT2|dllen), SDRC_DLLA_CTRL);
- __raw_writel(sdata->sdrc_dllab_ctrl, SDRC_DLLB_CTRL);
- __raw_writel(sdata->sdrc_dllab_ctrl & ~(BIT2|dllen) , SDRC_DLLB_CTRL);
- }
- sdelay(90000);
-
- if(mem_ok())
- return; /* STACKED, other configued type */
- ++pass_type; /* IPDDR->COMBODDR->IPSDR for CS0 */
- goto next_mem_type;
-}
-
-/*****************************************************
- * gpmc_init(): init gpmc bus
- * Init GPMC for x16, MuxMode (SDRAM in x32).
- * This code can only be executed from SRAM or SDRAM.
- *****************************************************/
-void gpmc_init(void)
-{
- u32 mux=0, mtype, mwidth, rev, tval;
-
- rev = get_cpu_rev();
- if (rev == CPU_2420_2422_ES1)
- tval = 1;
- else
- tval = 0; /* disable bit switched meaning */
-
- /* global settings */
- __raw_writel(0x10, GPMC_SYSCONFIG); /* smart idle */
- __raw_writel(0x0, GPMC_IRQENABLE); /* isr's sources masked */
- __raw_writel(tval, GPMC_TIMEOUT_CONTROL);/* timeout disable */
-#ifdef CONFIG_SYS_NAND_BOOT
- __raw_writel(0x001, GPMC_CONFIG); /* set nWP, disable limited addr */
-#else
- __raw_writel(0x111, GPMC_CONFIG); /* set nWP, disable limited addr */
-#endif
-
- /* discover bus connection from sysboot */
- if (is_gpmc_muxed() == GPMC_MUXED)
- mux = BIT9;
- mtype = get_gpmc0_type();
- mwidth = get_gpmc0_width();
-
- /* setup cs0 */
- __raw_writel(0x0, GPMC_CONFIG7_0); /* disable current map */
- sdelay(1000);
-
-#ifdef CONFIG_SYS_NAND_BOOT
- __raw_writel(H4_24XX_GPMC_CONFIG1_0|mtype|mwidth, GPMC_CONFIG1_0);
-#else
- __raw_writel(H4_24XX_GPMC_CONFIG1_0|mux|mtype|mwidth, GPMC_CONFIG1_0);
-#endif
-
-#ifdef PRCM_CONFIG_III
- __raw_writel(H4_24XX_GPMC_CONFIG2_0, GPMC_CONFIG2_0);
-#endif
- __raw_writel(H4_24XX_GPMC_CONFIG3_0, GPMC_CONFIG3_0);
- __raw_writel(H4_24XX_GPMC_CONFIG4_0, GPMC_CONFIG4_0);
-#ifdef PRCM_CONFIG_III
- __raw_writel(H4_24XX_GPMC_CONFIG5_0, GPMC_CONFIG5_0);
- __raw_writel(H4_24XX_GPMC_CONFIG6_0, GPMC_CONFIG6_0);
-#endif
- __raw_writel(H4_24XX_GPMC_CONFIG7_0, GPMC_CONFIG7_0);/* enable new mapping */
- sdelay(2000);
-
- /* setup cs1 */
- __raw_writel(0, GPMC_CONFIG7_1); /* disable any mapping */
- sdelay(1000);
- __raw_writel(H4_24XX_GPMC_CONFIG1_1|mux, GPMC_CONFIG1_1);
- __raw_writel(H4_24XX_GPMC_CONFIG2_1, GPMC_CONFIG2_1);
- __raw_writel(H4_24XX_GPMC_CONFIG3_1, GPMC_CONFIG3_1);
- __raw_writel(H4_24XX_GPMC_CONFIG4_1, GPMC_CONFIG4_1);
- __raw_writel(H4_24XX_GPMC_CONFIG5_1, GPMC_CONFIG5_1);
- __raw_writel(H4_24XX_GPMC_CONFIG6_1, GPMC_CONFIG6_1);
- __raw_writel(H4_24XX_GPMC_CONFIG7_1, GPMC_CONFIG7_1); /* enable mapping */
- sdelay(2000);
-}
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Richard Woodruff <r-woodruff2@ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#include <common.h>
-#include <asm/arch/omap2420.h>
-#include <asm/io.h>
-#include <asm/arch/bits.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/sys_info.h>
-#include <asm/arch/mem.h>
-#include <i2c.h>
-#include <asm/mach-types.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-void wait_for_command_complete(unsigned int wd_base);
-
-/*******************************************************
- * Routine: delay
- * Description: spinning delay to use before udelay works
- ******************************************************/
-static inline void delay (unsigned long loops)
-{
- __asm__ volatile ("1:\n" "subs %0, %1, #1\n"
- "bne 1b":"=r" (loops):"0" (loops));
-}
-
-/*****************************************
- * Routine: board_init
- * Description: Early hardware init.
- *****************************************/
-int board_init (void)
-{
- gpmc_init(); /* in SRAM or SDRM, finish GPMC */
-
- gd->bd->bi_arch_number = MACH_TYPE_OMAP_H4; /* board id for linux */
- gd->bd->bi_boot_params = (OMAP2420_SDRC_CS0+0x100); /* adress of boot parameters */
-
- return 0;
-}
-
-/**********************************************************
- * Routine: try_unlock_sram()
- * Description: If chip is GP type, unlock the SRAM for
- * general use.
- ***********************************************************/
-void try_unlock_sram(void)
-{
- /* if GP device unlock device SRAM for general use */
- if (get_device_type() == GP_DEVICE) {
- __raw_writel(0xFF, A_REQINFOPERM0);
- __raw_writel(0xCFDE, A_READPERM0);
- __raw_writel(0xCFDE, A_WRITEPERM0);
- }
-}
-
-/**********************************************************
- * Routine: s_init
- * Description: Does early system init of muxing and clocks.
- * - Called path is with sram stack.
- **********************************************************/
-void s_init(void)
-{
- int in_sdram = running_in_sdram();
-
- watchdog_init();
- set_muxconf_regs();
- delay(100);
- try_unlock_sram();
-
- if(!in_sdram)
- prcm_init();
-
- peripheral_enable();
- icache_enable();
- if (!in_sdram)
- sdrc_init();
-}
-
-/*******************************************************
- * Routine: misc_init_r
- * Description: Init ethernet (done here so udelay works)
- ********************************************************/
-int misc_init_r (void)
-{
- ether_init(); /* better done here so timers are init'ed */
- return(0);
-}
-
-/****************************************
- * Routine: watchdog_init
- * Description: Shut down watch dogs
- *****************************************/
-void watchdog_init(void)
-{
- /* There are 4 watch dogs. 1 secure, and 3 general purpose.
- * The ROM takes care of the secure one. Of the 3 GP ones,
- * 1 can reset us directly, the other 2 only generate MPU interrupts.
- */
- __raw_writel(WD_UNLOCK1 ,WD2_BASE+WSPR);
- wait_for_command_complete(WD2_BASE);
- __raw_writel(WD_UNLOCK2 ,WD2_BASE+WSPR);
-
-#if MPU_WD_CLOCKED /* value 0x10 stick on aptix, BIT4 polarity seems oppsite*/
- __raw_writel(WD_UNLOCK1 ,WD3_BASE+WSPR);
- wait_for_command_complete(WD3_BASE);
- __raw_writel(WD_UNLOCK2 ,WD3_BASE+WSPR);
-
- __raw_writel(WD_UNLOCK1 ,WD4_BASE+WSPR);
- wait_for_command_complete(WD4_BASE);
- __raw_writel(WD_UNLOCK2 ,WD4_BASE+WSPR);
-#endif
-}
-
-/******************************************************
- * Routine: wait_for_command_complete
- * Description: Wait for posting to finish on watchdog
- ******************************************************/
-void wait_for_command_complete(unsigned int wd_base)
-{
- int pending = 1;
- do {
- pending = __raw_readl(wd_base+WWPS);
- } while (pending);
-}
-
-/*******************************************************************
- * Routine:ether_init
- * Description: take the Ethernet controller out of reset and wait
- * for the EEPROM load to complete.
- ******************************************************************/
-void ether_init (void)
-{
-#ifdef CONFIG_DRIVER_LAN91C96
- int cnt = 20;
-
- __raw_writeb(0x3,OMAP2420_CTRL_BASE+0x10a); /*protect->gpio95 */
-
- __raw_writew(0x0, LAN_RESET_REGISTER);
- do {
- __raw_writew(0x1, LAN_RESET_REGISTER);
- udelay (100);
- if (cnt == 0)
- goto h4reset_err_out;
- --cnt;
- } while (__raw_readw(LAN_RESET_REGISTER) != 0x1);
-
- cnt = 20;
-
- do {
- __raw_writew(0x0, LAN_RESET_REGISTER);
- udelay (100);
- if (cnt == 0)
- goto h4reset_err_out;
- --cnt;
- } while (__raw_readw(LAN_RESET_REGISTER) != 0x0000);
- udelay (1000);
-
- *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
- udelay (1000);
-
- h4reset_err_out:
- return;
-#endif
-}
-
-/**********************************************
- * Routine: dram_init
- * Description: sets uboots idea of sdram size
- **********************************************/
-int dram_init (void)
-{
- unsigned int size0=0,size1=0;
- u32 mtype, btype, rev, cpu;
- u8 chg_on = 0x5; /* enable charge of back up battery */
- u8 vmode_on = 0x8C;
- #define NOT_EARLY 0
-
- i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); /* need this a bit early */
-
- btype = get_board_type();
- mtype = get_mem_type();
- rev = get_cpu_rev();
- cpu = get_cpu_type();
-
- display_board_info(btype);
- if (btype == BOARD_H4_MENELAUS){
- update_mux(btype,mtype); /* combo part on menelaus */
- i2c_write(I2C_MENELAUS, 0x20, 1, &chg_on, 1); /*fix POR reset bug */
- i2c_write(I2C_MENELAUS, 0x2, 1, &vmode_on, 1); /* VCORE change on VMODE */
- }
-
- if ((mtype == DDR_COMBO) || (mtype == DDR_STACKED)) {
- do_sdrc_init(SDRC_CS1_OSET, NOT_EARLY); /* init other chip select */
- }
- size0 = get_sdr_cs_size(SDRC_CS0_OSET);
- size1 = get_sdr_cs_size(SDRC_CS1_OSET);
-
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = size0;
- if(rev == CPU_2420_2422_ES1) /* ES1's 128MB remap granularity isn't worth doing */
- gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
- else /* ES2 and above can remap at 32MB granularity */
- gd->bd->bi_dram[1].start = PHYS_SDRAM_1+size0;
- gd->bd->bi_dram[1].size = size1;
-
- return 0;
-}
-
-/**********************************************************
- * Routine: set_muxconf_regs
- * Description: Setting up the configuration Mux registers
- * specific to the hardware
- *********************************************************/
-void set_muxconf_regs (void)
-{
- muxSetupSDRC();
- muxSetupGPMC();
- muxSetupUsb0();
- muxSetupUart3();
- muxSetupI2C1();
- muxSetupUART1();
- muxSetupLCD();
- muxSetupCamera();
- muxSetupMMCSD();
- muxSetupTouchScreen();
- muxSetupHDQ();
-}
-
-/*****************************************************************
- * Routine: peripheral_enable
- * Description: Enable the clks & power for perifs (GPT2, UART1,...)
- ******************************************************************/
-void peripheral_enable(void)
-{
- unsigned int v, if_clks=0, func_clks=0;
-
- /* Enable GP2 timer.*/
- if_clks |= BIT4;
- func_clks |= BIT4;
- v = __raw_readl(CM_CLKSEL2_CORE) | 0x4; /* Sys_clk input OMAP2420_GPT2 */
- __raw_writel(v, CM_CLKSEL2_CORE);
- __raw_writel(0x1, CM_CLKSEL_WKUP);
-
-#ifdef CONFIG_SYS_NS16550
- /* Enable UART1 clock */
- func_clks |= BIT21;
- if_clks |= BIT21;
-#endif
- v = __raw_readl(CM_ICLKEN1_CORE) | if_clks; /* Interface clocks on */
- __raw_writel(v,CM_ICLKEN1_CORE );
- v = __raw_readl(CM_FCLKEN1_CORE) | func_clks; /* Functional Clocks on */
- __raw_writel(v, CM_FCLKEN1_CORE);
- delay(1000);
-
-#ifndef KERNEL_UPDATED
- {
-#define V1 0xffffffff
-#define V2 0x00000007
-
- __raw_writel(V1, CM_FCLKEN1_CORE);
- __raw_writel(V2, CM_FCLKEN2_CORE);
- __raw_writel(V1, CM_ICLKEN1_CORE);
- __raw_writel(V1, CM_ICLKEN2_CORE);
- }
-#endif
-}
-
-/****************************************
- * Routine: muxSetupUsb0 (ostboot)
- * Description: Setup usb muxing
- *****************************************/
-void muxSetupUsb0(void)
-{
- volatile uint8 *MuxConfigReg;
- volatile uint32 *otgCtrlReg;
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_PUEN;
- *MuxConfigReg &= (uint8)(~0x1F);
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_VP;
- *MuxConfigReg &= (uint8)(~0x1F);
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_VM;
- *MuxConfigReg &= (uint8)(~0x1F);
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_RCV;
- *MuxConfigReg &= (uint8)(~0x1F);
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_TXEN;
- *MuxConfigReg &= (uint8)(~0x1F);
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_SE0;
- *MuxConfigReg &= (uint8)(~0x1F);
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_DAT;
- *MuxConfigReg &= (uint8)(~0x1F);
-
- /* setup for USB VBus detection */
- otgCtrlReg = (volatile uint32 *)USB_OTG_CTRL;
- *otgCtrlReg |= 0x00040000; /* bit 18 */
-}
-
-/****************************************
- * Routine: muxSetupUart3 (ostboot)
- * Description: Setup uart3 muxing
- *****************************************/
-void muxSetupUart3(void)
-{
- volatile uint8 *MuxConfigReg;
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_UART3_TX_IRTX;
- *MuxConfigReg &= (uint8)(~0x1F);
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_UART3_RX_IRRX;
- *MuxConfigReg &= (uint8)(~0x1F);
-}
-
-/****************************************
- * Routine: muxSetupI2C1 (ostboot)
- * Description: Setup i2c muxing
- *****************************************/
-void muxSetupI2C1(void)
-{
- volatile unsigned char *MuxConfigReg;
-
- /* I2C1 Clock pin configuration, PIN = M19 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_I2C1_SCL;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* I2C1 Data pin configuration, PIN = L15 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_I2C1_SDA;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* Pull-up required on data line */
- /* external pull-up already present. */
- /* *MuxConfigReg |= 0x18 ;*/ /* Mode = 0, PullTypeSel=PU, PullUDEnable=Enabled */
-}
-
-/****************************************
- * Routine: muxSetupUART1 (ostboot)
- * Description: Set up uart1 muxing
- *****************************************/
-void muxSetupUART1(void)
-{
- volatile unsigned char *MuxConfigReg;
-
- /* UART1_CTS pin configuration, PIN = D21 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_CTS;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* UART1_RTS pin configuration, PIN = H21 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_RTS;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* UART1_TX pin configuration, PIN = L20 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_TX;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* UART1_RX pin configuration, PIN = T21 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_RX;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-}
-
-/****************************************
- * Routine: muxSetupLCD (ostboot)
- * Description: Setup lcd muxing
- *****************************************/
-void muxSetupLCD(void)
-{
- volatile unsigned char *MuxConfigReg;
-
- /* LCD_D0 pin configuration, PIN = Y7 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D0;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D1 pin configuration, PIN = P10 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D1;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D2 pin configuration, PIN = V8 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D2;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D3 pin configuration, PIN = Y8 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D3;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D4 pin configuration, PIN = W8 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D4;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D5 pin configuration, PIN = R10 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D5;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D6 pin configuration, PIN = Y9 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D6;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D7 pin configuration, PIN = V9 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D7;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D8 pin configuration, PIN = W9 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D8;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D9 pin configuration, PIN = P11 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D9;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D10 pin configuration, PIN = V10 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D10;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D11 pin configuration, PIN = Y10 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D11;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D12 pin configuration, PIN = W10 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D12;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D13 pin configuration, PIN = R11 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D13;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D14 pin configuration, PIN = V11 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D14;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D15 pin configuration, PIN = W11 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D15;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D16 pin configuration, PIN = P12 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D16;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D17 pin configuration, PIN = R12 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D17;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_PCLK pin configuration, PIN = W6 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_PCLK;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_VSYNC pin configuration, PIN = V7 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_VSYNC;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_HSYNC pin configuration, PIN = Y6 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_HSYNC;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_ACBIAS pin configuration, PIN = W7 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_ACBIAS;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-}
-
-/****************************************
- * Routine: muxSetupCamera (ostboot)
- * Description: Setup camera muxing
- *****************************************/
-void muxSetupCamera(void)
-{
- volatile unsigned char *MuxConfigReg;
-
- /* CAMERA_RSTZ pin configuration, PIN = Y16 */
- /* CAM_RST is connected through the I2C IO expander.*/
- /* MuxConfigReg = (volatile unsigned char *), CONTROL_PADCONF_SYS_NRESWARM*/
- /* *MuxConfigReg = 0x00 ; / * Mode = 0, PUPD=Disabled */
-
- /* CAMERA_XCLK pin configuration, PIN = U3 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_XCLK;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_LCLK pin configuration, PIN = V5 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_LCLK;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_VSYNC pin configuration, PIN = U2 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_VS,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_HSYNC pin configuration, PIN = T3 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_HS,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT0 pin configuration, PIN = T4 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D0,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT1 pin configuration, PIN = V2 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D1,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT2 pin configuration, PIN = V3 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D2,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT3 pin configuration, PIN = U4 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D3,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT4 pin configuration, PIN = W2 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D4,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT5 pin configuration, PIN = V4 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D5,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT6 pin configuration, PIN = W3 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D6,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT7 pin configuration, PIN = Y2 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D7,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT8 pin configuration, PIN = Y4 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D8,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT9 pin configuration, PIN = V6 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D9,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-}
-
-/****************************************
- * Routine: muxSetupMMCSD (ostboot)
- * Description: set up MMC muxing
- *****************************************/
-void muxSetupMMCSD(void)
-{
- volatile unsigned char *MuxConfigReg;
-
- /* SDMMC_CLKI pin configuration, PIN = H15 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CLKI,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SDMMC_CLKO pin configuration, PIN = G19 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CLKO,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SDMMC_CMD pin configuration, PIN = H18 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CMD,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
- /* External pull-ups are present. */
- /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */
-
- /* SDMMC_DAT0 pin configuration, PIN = F20 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT0,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
- /* External pull-ups are present. */
- /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */
-
- /* SDMMC_DAT1 pin configuration, PIN = H14 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT1,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
- /* External pull-ups are present. */
- /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */
-
- /* SDMMC_DAT2 pin configuration, PIN = E19 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT2,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
- /* External pull-ups are present. */
- /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */
-
- /* SDMMC_DAT3 pin configuration, PIN = D19 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT3,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
- /* External pull-ups are present. */
- /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */
-
- /* SDMMC_DDIR0 pin configuration, PIN = F19 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR0,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SDMMC_DDIR1 pin configuration, PIN = E20 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR1,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SDMMC_DDIR2 pin configuration, PIN = F18 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR2,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SDMMC_DDIR3 pin configuration, PIN = E18 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR3,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SDMMC_CDIR pin configuration, PIN = G18 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CMD_DIR,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* MMC_CD pin configuration, PIN = B3 ---2420IP ONLY---*/
- /* MMC_CD for 2422IP=K1 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SDRC_A14,
- *MuxConfigReg = 0x03 ; /* Mode = 3, PUPD=Disabled */
-
- /* MMC_WP pin configuration, PIN = B4 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SDRC_A13,
- *MuxConfigReg = 0x03 ; /* Mode = 3, PUPD=Disabled */
-}
-
-/******************************************
- * Routine: muxSetupTouchScreen (ostboot)
- * Description: Set up touch screen muxing
- *******************************************/
-void muxSetupTouchScreen(void)
-{
- volatile unsigned char *MuxConfigReg;
-
- /* SPI1_CLK pin configuration, PIN = U18 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_CLK,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SPI1_MOSI pin configuration, PIN = V20 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_SIMO,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SPI1_MISO pin configuration, PIN = T18 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_SOMI,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SPI1_nCS0 pin configuration, PIN = U19 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_NCS0,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* PEN_IRQ pin configuration, PIN = P20 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MCBSP1_FSR,
- *MuxConfigReg = 0x03 ; /* Mode = 3, PUPD=Disabled */
-}
-
-/****************************************
- * Routine: muxSetupHDQ (ostboot)
- * Description: setup 1wire mux
- *****************************************/
-void muxSetupHDQ(void)
-{
- volatile unsigned char *MuxConfigReg;
-
- /* HDQ_SIO pin configuration, PIN = N18 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_HDQ_SIO,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-}
-
-/***************************************************************
- * Routine: muxSetupGPMC (ostboot)
- * Description: Configures balls which cam up in protected mode
- ***************************************************************/
-void muxSetupGPMC(void)
-{
- volatile uint8 *MuxConfigReg;
- volatile unsigned int *MCR = (volatile unsigned int *)0x4800008C;
-
- /* gpmc_io_dir */
- *MCR = 0x19000000;
-
- /* NOR FLASH CS0 */
- /* signal - Gpmc_clk; pin - J4; offset - 0x0088; mode - 0; Byte-3 Pull/up - N/A */
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_D2_BYTE3,
- *MuxConfigReg = 0x00 ;
-
- /* signal - Gpmc_iodir; pin - n2; offset - 0x008C; mode - 1; Byte-3 Pull/up - N/A */
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE3,
- *MuxConfigReg = 0x01 ;
-
- /* MPDB(Multi Port Debug Port) CS1 */
- /* signal - gpmc_ncs1; pin - N8; offset - 0x008C; mode - 0; Byte-1 Pull/up - N/A */
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE1,
- *MuxConfigReg = 0x00 ;
-
- /* signal - Gpmc_ncs2; pin - E2; offset - 0x008C; mode - 0; Byte-2 Pull/up - N/A */
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE2,
- *MuxConfigReg = 0x00 ;
-}
-
-/****************************************************************
- * Routine: muxSetupSDRC (ostboot)
- * Description: Configures balls which come up in protected mode
- ****************************************************************/
-void muxSetupSDRC(void)
-{
- volatile uint8 *MuxConfigReg;
-
- /* signal - sdrc_ncs1; pin - C12; offset - 0x00A0; mode - 0; Byte-1 Pull/up - N/A */
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_SDRC_NCS0_BYTE1,
- *MuxConfigReg = 0x00 ;
-
- /* signal - sdrc_a12; pin - D11; offset - 0x0030; mode - 0; Byte-2 Pull/up - N/A */
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_SDRC_A14_BYTE2,
- *MuxConfigReg = 0x00 ;
-
- /* signal - sdrc_cke1; pin - B13; offset - 0x00A0; mode - 0; Byte-3 Pull/up - N/A */
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_SDRC_NCS0_BYTE3,
- *MuxConfigReg = 0x00;
-
- if (get_cpu_type() == CPU_2422) {
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_SDRC_A14_BYTE0,
- *MuxConfigReg = 0x1b;
- }
-}
-
-/*****************************************************************************
- * Routine: update_mux()
- * Description: Update balls which are different beween boards. All should be
- * updated to match functionaly. However, I'm only updating ones
- * which I'll be using for now. When power comes into play they
- * all need updating.
- *****************************************************************************/
-void update_mux(u32 btype,u32 mtype)
-{
- u32 cpu, base = OMAP2420_CTRL_BASE;
- cpu = get_cpu_type();
-
- if (btype == BOARD_H4_MENELAUS) {
- if (cpu == CPU_2420) {
- /* PIN = B3, GPIO.0->KBR5, mode 3, (pun?),-DO-*/
- __raw_writeb(0x3, base+0x30);
- /* PIN = B13, GPIO.38->KBC6, mode 3, (pun?)-DO-*/
- __raw_writeb(0x3, base+0xa3);
- /* PIN = F1, GPIO.25->HSUSBxx mode 3, (for external HS USB)*/
- /* PIN = H1, GPIO.26->HSUSBxx mode 3, (for external HS USB)*/
- /* PIN = K1, GPMC_ncs6 mode 0, (on board nand access)*/
- /* PIN = L2, GPMC_ncs67 mode 0, (for external HS USB)*/
- /* PIN = M1 (HSUSBOTG) */
- /* PIN = P1, GPIO.35->MEN_POK mode 3, (menelaus powerok)-DO-*/
- __raw_writeb(0x3, base+0x9d);
- /* PIN = U32, (WLAN_CLKREQ) */
- /* PIN = Y11, WLAN */
- /* PIN = AA4, GPIO.15->KBC2, mode 3, -DO- */
- __raw_writeb(0x3, base+0xe7);
- /* PIN = AA8, mDOC */
- /* PIN = AA10, BT */
- /* PIN = AA13, WLAN */
- /* PIN = M18 GPIO.96->MMC2_WP mode 3 -DO- */
- __raw_writeb(0x3, base+0x10e);
- /* PIN = N19 GPIO.98->WLAN_INT mode 3 -DO- */
- __raw_writeb(0x3, base+0x110);
- /* PIN = J15 HHUSB */
- /* PIN = H19 HSUSB */
- /* PIN = W13, P13, R13, W16 ... */
- /* PIN = V12 GPIO.25->I2C_CAMEN mode 3 -DO- */
- __raw_writeb(0x3, base+0xde);
- /* PIN = W19 sys_nirq->MENELAUS_INT mode 0 -DO- */
- __raw_writeb(0x0, base+0x12c);
- /* PIN = AA17->sys_clkreq mode 0 -DO- */
- __raw_writeb(0x0, base+0x136);
- } else if (cpu == CPU_2422) {
- /* PIN = B3, GPIO.0->nc, mode 3, set above (pun?)*/
- /* PIN = B13, GPIO.cke1->nc, mode 0, set above, (pun?)*/
- /* PIN = F1, GPIO.25->HSUSBxx mode 3, (for external HS USB)*/
- /* PIN = H1, GPIO.26->HSUSBxx mode 3, (for external HS USB)*/
- /* PIN = K1, GPMC_ncs6 mode 0, (on board nand access)*/
- __raw_writeb(0x0, base+0x92);
- /* PIN = L2, GPMC_ncs67 mode 0, (for external HS USB)*/
- /* PIN = M1 (HSUSBOTG) */
- /* PIN = P1, GPIO.35->MEN_POK mode 3, (menelaus powerok)-DO-*/
- __raw_writeb(0x3, base+0x10c);
- /* PIN = U32, (WLAN_CLKREQ) */
- /* PIN = AA4, GPIO.15->KBC2, mode 3, -DO- */
- __raw_writeb(0x3, base+0x30);
- /* PIN = AA8, mDOC */
- /* PIN = AA10, BT */
- /* PIN = AA12, WLAN */
- /* PIN = M18 GPIO.96->MMC2_WP mode 3 -DO- */
- __raw_writeb(0x3, base+0x10e);
- /* PIN = N19 GPIO.98->WLAN_INT mode 3 -DO- */
- __raw_writeb(0x3, base+0x110);
- /* PIN = J15 HHUSB */
- /* PIN = H19 HSUSB */
- /* PIN = W13, P13, R13, W16 ... */
- /* PIN = V12 GPIO.25->I2C_CAMEN mode 3 -DO- */
- __raw_writeb(0x3, base+0xde);
- /* PIN = W19 sys_nirq->MENELAUS_INT mode 0 -DO- */
- __raw_writeb(0x0, base+0x12c);
- /* PIN = AA17->sys_clkreq mode 0 -DO- */
- __raw_writeb(0x0, base+0x136);
- }
-
- } else if (btype == BOARD_H4_SDP) {
- if (cpu == CPU_2420) {
- /* PIN = B3, GPIO.0->nc mode 3, set above (pun?)*/
- /* PIN = B13, GPIO.cke1->nc, mode 0, set above, (pun?)*/
- /* Pin = Y11 VLNQ */
- /* Pin = AA4 VLNQ */
- /* Pin = AA6 VLNQ */
- /* Pin = AA8 VLNQ */
- /* Pin = AA10 VLNQ */
- /* Pin = AA12 VLNQ */
- /* PIN = M18 GPIO.96->KBR5 mode 3 -DO- */
- __raw_writeb(0x3, base+0x10e);
- /* PIN = N19 GPIO.98->KBC6 mode 3 -DO- */
- __raw_writeb(0x3, base+0x110);
- /* PIN = J15 MDOC_nDMAREQ */
- /* PIN = H19 GPIO.100->KBC2 mode 3 -DO- */
- __raw_writeb(0x3, base+0x114);
- /* PIN = W13, V12, P13, R13, W19, W16 ... */
- /* PIN = AA17 sys_clkreq->bt_clk_req mode 0 */
- } else if (cpu == CPU_2422) {
- /* PIN = B3, GPIO.0->MMC_CD, mode 3, set above */
- /* PIN = B13, GPIO.38->wlan_int, mode 3, (pun?)*/
- /* Pin = Y11 VLNQ */
- /* Pin = AA4 VLNQ */
- /* Pin = AA6 VLNQ */
- /* Pin = AA8 VLNQ */
- /* Pin = AA10 VLNQ */
- /* Pin = AA12 VLNQ */
- /* PIN = M18 GPIO.96->KBR5 mode 3 -DO- */
- __raw_writeb(0x3, base+0x10e);
- /* PIN = N19 GPIO.98->KBC6 mode 3 -DO- */
- __raw_writeb(0x3, base+0x110);
- /* PIN = J15 MDOC_nDMAREQ */
- /* PIN = H19 GPIO.100->KBC2 mode 3 -DO- */
- __raw_writeb(0x3, base+0x114);
- /* PIN = W13, V12, P13, R13, W19, W16 ... */
- /* PIN = AA17 sys_clkreq->bt_clk_req mode 0 */
- }
- }
-}
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Richard Woodruff <r-woodruff2@ti.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/arch/omap2420.h>
-#include <asm/io.h>
-#include <asm/arch/bits.h>
-#include <asm/arch/mem.h> /* get mem tables */
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/sys_info.h>
-#include <i2c.h>
-
-/**************************************************************************
- * get_prod_id() - get id info from chips
- ***************************************************************************/
-static u32 get_prod_id(void)
-{
- u32 p;
- p = __raw_readl(PRODUCTION_ID); /* get production ID */
- return((p & CPU_242X_PID_MASK) >> 16);
-}
-
-/**************************************************************************
- * get_cpu_type() - low level get cpu type
- * - no C globals yet.
- * - just looking to say if this is a 2422 or 2420 or ...
- * - to start with we will look at switch settings..
- * - 2422 id's same as 2420 for ES1 will rely on H4 board characteristics
- * (mux for 2420, non-mux for 2422).
- ***************************************************************************/
-u32 get_cpu_type(void)
-{
- u32 v;
-
- switch(get_prod_id()){
- case 1:;/* 2420 */
- case 2: return(CPU_2420); break; /* 2420 pop */
- case 4: return(CPU_2422); break;
- case 8: return(CPU_2423); break;
- default: break; /* early 2420/2422's unmarked */
- }
-
- v = __raw_readl(TAP_IDCODE_REG);
- v &= CPU_24XX_ID_MASK;
- if (v == CPU_2420_CHIPID) { /* currently 2420 and 2422 have same id */
- if (is_gpmc_muxed() == GPMC_MUXED) /* if mux'ed */
- return(CPU_2420);
- else
- return(CPU_2422);
- } else
- return(CPU_2420); /* don't know, say 2420 */
-}
-
-/******************************************
- * get_cpu_rev(void) - extract version info
- ******************************************/
-u32 get_cpu_rev(void)
-{
- u32 v;
- v = __raw_readl(TAP_IDCODE_REG);
- v = v >> 28;
- return(v+1); /* currently 2422 and 2420 match up */
-}
-/****************************************************
- * is_mem_sdr() - return 1 if mem type in use is SDR
- ****************************************************/
-u32 is_mem_sdr(void)
-{
- volatile u32 *burst = (volatile u32 *)(SDRC_MR_0+SDRC_CS0_OSET);
- if(*burst == H4_2420_SDRC_MR_0_SDR)
- return(1);
- return(0);
-}
-
-/***********************************************************
- * get_mem_type() - identify type of mDDR part used.
- * 2422 uses stacked DDR, 2 parts CS0/CS1.
- * 2420 may have 1 or 2, no good way to know...only init 1...
- * when eeprom data is up we can select 1 more.
- *************************************************************/
-u32 get_mem_type(void)
-{
- u32 cpu, sdr = is_mem_sdr();
-
- cpu = get_cpu_type();
- if (cpu == CPU_2422 || cpu == CPU_2423)
- return(DDR_STACKED);
-
- if(get_prod_id() == 0x2)
- return(XDR_POP);
-
- if (get_board_type() == BOARD_H4_MENELAUS)
- if(sdr)
- return(SDR_DISCRETE);
- else
- return(DDR_COMBO);
- else
- if(sdr) /* SDP + SDR kit */
- return(SDR_DISCRETE);
- else
- return(DDR_DISCRETE); /* origional SDP */
-}
-
-/***********************************************************************
- * get_cs0_size() - get size of chip select 0/1
- ************************************************************************/
-u32 get_sdr_cs_size(u32 offset)
-{
- u32 size;
- size = __raw_readl(SDRC_MCFG_0+offset) >> 8; /* get ram size field */
- size &= 0x2FF; /* remove unwanted bits */
- size *= SZ_2M; /* find size in MB */
- return(size);
-}
-
-/***********************************************************************
- * get_board_type() - get board type based on current production stats.
- * --- NOTE: 2 I2C EEPROMs will someday be populated with proper info.
- * when they are available we can get info from there. This should
- * be correct of all known boards up until today.
- ************************************************************************/
-u32 get_board_type(void)
-{
- if (i2c_probe(I2C_MENELAUS) == 0)
- return(BOARD_H4_MENELAUS);
- else
- return(BOARD_H4_SDP);
-}
-
-/******************************************************************
- * get_sysboot_value() - get init word settings (dip switch on h4)
- ******************************************************************/
-inline u32 get_sysboot_value(void)
-{
- return(0x00000FFF & __raw_readl(CONTROL_STATUS));
-}
-
-/***************************************************************************
- * get_gpmc0_base() - Return current address hardware will be
- * fetching from. The below effectively gives what is correct, its a bit
- * mis-leading compared to the TRM. For the most general case the mask
- * needs to be also taken into account this does work in practice.
- * - for u-boot we currently map:
- * -- 0 to nothing,
- * -- 4 to flash
- * -- 8 to enent
- * -- c to wifi
- ****************************************************************************/
-u32 get_gpmc0_base(void)
-{
- u32 b;
-
- b = __raw_readl(GPMC_CONFIG7_0);
- b &= 0x1F; /* keep base [5:0] */
- b = b << 24; /* ret 0x0b000000 */
- return(b);
-}
-
-/*****************************************************************
- * is_gpmc_muxed() - tells if address/data lines are multiplexed
- *****************************************************************/
-u32 is_gpmc_muxed(void)
-{
- u32 mux;
- mux = get_sysboot_value();
- if ((mux & (BIT0 | BIT1 | BIT2 | BIT3)) == (BIT0 | BIT2 | BIT3))
- return(GPMC_MUXED); /* NAND Boot mode */
- if (mux & BIT1) /* if mux'ed */
- return(GPMC_MUXED);
- else
- return(GPMC_NONMUXED);
-}
-
-/************************************************************************
- * get_gpmc0_type() - read sysboot lines to see type of memory attached
- ************************************************************************/
-u32 get_gpmc0_type(void)
-{
- u32 type;
- type = get_sysboot_value();
- if ((type & (BIT3|BIT2)) == (BIT3|BIT2))
- return(TYPE_NAND);
- else
- return(TYPE_NOR);
-}
-
-/*******************************************************************
- * get_gpmc0_width() - See if bus is in x8 or x16 (mainly for nand)
- *******************************************************************/
-u32 get_gpmc0_width(void)
-{
- u32 width;
- width = get_sysboot_value();
- if ((width & 0xF) == (BIT3|BIT2))
- return(WIDTH_8BIT);
- else
- return(WIDTH_16BIT);
-}
-
-/*********************************************************************
- * wait_on_value() - common routine to allow waiting for changes in
- * volatile regs.
- *********************************************************************/
-u32 wait_on_value(u32 read_bit_mask, u32 match_value, u32 read_addr, u32 bound)
-{
- u32 i = 0, val;
- do {
- ++i;
- val = __raw_readl(read_addr) & read_bit_mask;
- if (val == match_value)
- return(1);
- if (i==bound)
- return(0);
- } while (1);
-}
-
-/*********************************************************************
- * display_board_info() - print banner with board info.
- *********************************************************************/
-void display_board_info(u32 btype)
-{
- char cpu_2420[] = "2420"; /* cpu type */
- char cpu_2422[] = "2422";
- char cpu_2423[] = "2423";
- char db_men[] = "Menelaus"; /* board type */
- char db_ip[] = "IP";
- char mem_sdr[] = "mSDR"; /* memory type */
- char mem_ddr[] = "mDDR";
- char t_tst[] = "TST"; /* security level */
- char t_emu[] = "EMU";
- char t_hs[] = "HS";
- char t_gp[] = "GP";
- char unk[] = "?";
-
- char *cpu_s, *db_s, *mem_s, *sec_s;
- u32 cpu, rev, sec;
-
- rev = get_cpu_rev();
- cpu = get_cpu_type();
- sec = get_device_type();
-
- if(is_mem_sdr())
- mem_s = mem_sdr;
- else
- mem_s = mem_ddr;
-
- if(cpu == CPU_2423)
- cpu_s = cpu_2423;
- else if (cpu == CPU_2422)
- cpu_s = cpu_2422;
- else
- cpu_s = cpu_2420;
-
- if(btype == BOARD_H4_MENELAUS)
- db_s = db_men;
- else
- db_s = db_ip;
-
- switch(sec){
- case TST_DEVICE: sec_s = t_tst; break;
- case EMU_DEVICE: sec_s = t_emu; break;
- case HS_DEVICE: sec_s = t_hs; break;
- case GP_DEVICE: sec_s = t_gp; break;
- default: sec_s = unk;
- }
-
- printf("OMAP%s-%s revision %d\n", cpu_s, sec_s, rev-1);
- printf("TI H4 SDP Base Board + %s Daughter Board + %s \n", db_s, mem_s);
-}
-
-/*************************************************************************
- * get_board_rev() - setup to pass kernel board revision information
- * 0 = 242x IP platform (first 2xx boards)
- * 1 = 242x Menelaus platfrom.
- *************************************************************************/
-u32 get_board_rev(void)
-{
- u32 rev = 0;
- u32 btype = get_board_type();
-
- if (btype == BOARD_H4_MENELAUS){
- rev = 1;
- }
- return(rev);
-}
-
-/********************************************************
- * get_base(); get upper addr of current execution
- *******************************************************/
-u32 get_base(void)
-{
- u32 val;
- __asm__ __volatile__("mov %0, pc \n" : "=r" (val) : : "memory");
- val &= 0xF0000000;
- val >>= 28;
- return(val);
-}
-
-/********************************************************
- * get_base2(); get 2upper addr of current execution
- *******************************************************/
-u32 get_base2(void)
-{
- u32 val;
- __asm__ __volatile__("mov %0, pc \n" : "=r" (val) : : "memory");
- val &= 0xFF000000;
- val >>= 24;
- return(val);
-}
-
-/********************************************************
- * running_in_flash() - tell if currently running in
- * flash.
- *******************************************************/
-u32 running_in_flash(void)
-{
- if (get_base() < 4)
- return(1); /* in flash */
- return(0); /* running in SRAM or SDRAM */
-}
-
-/********************************************************
- * running_in_sram() - tell if currently running in
- * sram.
- *******************************************************/
-u32 running_in_sram(void)
-{
- if (get_base() == 4)
- return(1); /* in SRAM */
- return(0); /* running in FLASH or SDRAM */
-}
-/********************************************************
- * running_in_sdram() - tell if currently running in
- * flash.
- *******************************************************/
-u32 running_in_sdram(void)
-{
- if (get_base() > 4)
- return(1); /* in sdram */
- return(0); /* running in SRAM or FLASH */
-}
-
-/*************************************************************
- * running_from_internal_boot() - am I a signed NOR image.
- *************************************************************/
-u32 running_from_internal_boot(void)
-{
- u32 v, base;
-
- v = get_sysboot_value() & BIT3;
- base = get_base2();
- /* if running at mask rom flash address and
- * sysboot3 says this was an internal boot
- */
- if ((base == 0x08) && v)
- return(1);
- else
- return(0);
-}
-
-/*************************************************************
- * get_device_type(): tell if GP/HS/EMU/TST
- *************************************************************/
-u32 get_device_type(void)
-{
- int mode;
- mode = __raw_readl(CONTROL_STATUS) & (BIT10|BIT9|BIT8);
- return(mode >>= 8);
-}
+++ /dev/null
-#
-# (C) Copyright 2000, 2001, 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = $(obj)lib$(BOARD).a
-
-COBJS := beagle.o
-
-SRCS := $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-
-$(LIB): $(obj).depend $(OBJS)
- $(AR) $(ARFLAGS) $@ $(OBJS)
-
-clean:
- rm -f $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
+++ /dev/null
-/*
- * (C) Copyright 2004-2008
- * Texas Instruments, <www.ti.com>
- *
- * Author :
- * Sunil Kumar <sunilsaini05@gmail.com>
- * Shashi Ranjan <shashiranjanmca05@gmail.com>
- *
- * Derived from Beagle Board and 3430 SDP code by
- * Richard Woodruff <r-woodruff2@ti.com>
- * Syed Mohammed Khasim <khasim@ti.com>
- *
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#include <common.h>
-#include <twl4030.h>
-#include <asm/io.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/gpio.h>
-#include <asm/mach-types.h>
-#include "beagle.h"
-
-static int beagle_revision_c;
-
-/*
- * Routine: board_init
- * Description: Early hardware init.
- */
-int board_init(void)
-{
- DECLARE_GLOBAL_DATA_PTR;
-
- gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
- /* board id for Linux */
- gd->bd->bi_arch_number = MACH_TYPE_OMAP3_BEAGLE;
- /* boot param addr */
- gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
-
- return 0;
-}
-
-/*
- * Routine: beagle_get_revision
- * Description: Return the revision of the BeagleBoard this code is running on.
- * If it is a revision Ax/Bx board, this function returns 0,
- * on a revision C board you will get a 1.
- */
-int beagle_get_revision(void)
-{
- return beagle_revision_c;
-}
-
-/*
- * Routine: beagle_identify
- * Description: Detect if we are running on a Beagle revision Ax/Bx or
- * Cx. This can be done by GPIO_171. If this is low, we are
- * running on a revision C board.
- */
-void beagle_identify(void)
-{
- beagle_revision_c = 0;
- if (!omap_request_gpio(171)) {
- unsigned int val;
-
- omap_set_gpio_direction(171, 1);
- val = omap_get_gpio_datain(171);
- omap_free_gpio(171);
-
- if (val)
- beagle_revision_c = 0;
- else
- beagle_revision_c = 1;
- }
-
- printf("Board revision ");
- if (beagle_revision_c)
- printf("C\n");
- else
- printf("Ax/Bx\n");
-}
-
-/*
- * Routine: misc_init_r
- * Description: Configure board specific parts
- */
-int misc_init_r(void)
-{
- struct gpio *gpio5_base = (struct gpio *)OMAP34XX_GPIO5_BASE;
- struct gpio *gpio6_base = (struct gpio *)OMAP34XX_GPIO6_BASE;
-
- twl4030_power_init();
- twl4030_led_init();
-
- /* Configure GPIOs to output */
- writel(~(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1), &gpio6_base->oe);
- writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
- GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
-
- /* Set GPIOs */
- writel(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1,
- &gpio6_base->setdataout);
- writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
- GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
-
- beagle_identify();
-
- dieid_num_r();
-
- return 0;
-}
-
-/*
- * Routine: set_muxconf_regs
- * Description: Setting up the configuration Mux registers specific to the
- * hardware. Many pins need to be moved from protect to primary
- * mode.
- */
-void set_muxconf_regs(void)
-{
- MUX_BEAGLE();
-
- if (beagle_revision_c) {
- MUX_BEAGLE_C();
- }
-}
+++ /dev/null
-/*
- * (C) Copyright 2008
- * Dirk Behme <dirk.behme@gmail.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#ifndef _BEAGLE_H_
-#define _BEAGLE_H_
-
-const omap3_sysinfo sysinfo = {
- DDR_STACKED,
- "OMAP3 Beagle board",
-#if defined(CONFIG_ENV_IS_IN_ONENAND)
- "OneNAND",
-#else
- "NAND",
-#endif
-};
-
-#define BOARD_REVISION_MASK (0x1 << 11)
-
-/*
- * IEN - Input Enable
- * IDIS - Input Disable
- * PTD - Pull type Down
- * PTU - Pull type Up
- * DIS - Pull type selection is inactive
- * EN - Pull type selection is active
- * M0 - Mode 0
- * The commented string gives the final mux configuration for that pin
- */
-#define MUX_BEAGLE() \
- /*SDRC*/\
- MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) /*SDRC_D0*/\
- MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) /*SDRC_D1*/\
- MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) /*SDRC_D2*/\
- MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) /*SDRC_D3*/\
- MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) /*SDRC_D4*/\
- MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) /*SDRC_D5*/\
- MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) /*SDRC_D6*/\
- MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) /*SDRC_D7*/\
- MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) /*SDRC_D8*/\
- MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) /*SDRC_D9*/\
- MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) /*SDRC_D10*/\
- MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) /*SDRC_D11*/\
- MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) /*SDRC_D12*/\
- MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) /*SDRC_D13*/\
- MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) /*SDRC_D14*/\
- MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) /*SDRC_D15*/\
- MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) /*SDRC_D16*/\
- MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) /*SDRC_D17*/\
- MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) /*SDRC_D18*/\
- MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) /*SDRC_D19*/\
- MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) /*SDRC_D20*/\
- MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) /*SDRC_D21*/\
- MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) /*SDRC_D22*/\
- MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) /*SDRC_D23*/\
- MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) /*SDRC_D24*/\
- MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) /*SDRC_D25*/\
- MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) /*SDRC_D26*/\
- MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) /*SDRC_D27*/\
- MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) /*SDRC_D28*/\
- MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) /*SDRC_D29*/\
- MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) /*SDRC_D30*/\
- MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) /*SDRC_D31*/\
- MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) /*SDRC_CLK*/\
- MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) /*SDRC_DQS0*/\
- MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) /*SDRC_DQS1*/\
- MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) /*SDRC_DQS2*/\
- MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) /*SDRC_DQS3*/\
- /*GPMC*/\
- MUX_VAL(CP(GPMC_A1), (IDIS | PTD | DIS | M0)) /*GPMC_A1*/\
- MUX_VAL(CP(GPMC_A2), (IDIS | PTD | DIS | M0)) /*GPMC_A2*/\
- MUX_VAL(CP(GPMC_A3), (IDIS | PTD | DIS | M0)) /*GPMC_A3*/\
- MUX_VAL(CP(GPMC_A4), (IDIS | PTD | DIS | M0)) /*GPMC_A4*/\
- MUX_VAL(CP(GPMC_A5), (IDIS | PTD | DIS | M0)) /*GPMC_A5*/\
- MUX_VAL(CP(GPMC_A6), (IDIS | PTD | DIS | M0)) /*GPMC_A6*/\
- MUX_VAL(CP(GPMC_A7), (IDIS | PTD | DIS | M0)) /*GPMC_A7*/\
- MUX_VAL(CP(GPMC_A8), (IDIS | PTD | DIS | M0)) /*GPMC_A8*/\
- MUX_VAL(CP(GPMC_A9), (IDIS | PTD | DIS | M0)) /*GPMC_A9*/\
- MUX_VAL(CP(GPMC_A10), (IDIS | PTD | DIS | M0)) /*GPMC_A10*/\
- MUX_VAL(CP(GPMC_D0), (IEN | PTD | DIS | M0)) /*GPMC_D0*/\
- MUX_VAL(CP(GPMC_D1), (IEN | PTD | DIS | M0)) /*GPMC_D1*/\
- MUX_VAL(CP(GPMC_D2), (IEN | PTD | DIS | M0)) /*GPMC_D2*/\
- MUX_VAL(CP(GPMC_D3), (IEN | PTD | DIS | M0)) /*GPMC_D3*/\
- MUX_VAL(CP(GPMC_D4), (IEN | PTD | DIS | M0)) /*GPMC_D4*/\
- MUX_VAL(CP(GPMC_D5), (IEN | PTD | DIS | M0)) /*GPMC_D5*/\
- MUX_VAL(CP(GPMC_D6), (IEN | PTD | DIS | M0)) /*GPMC_D6*/\
- MUX_VAL(CP(GPMC_D7), (IEN | PTD | DIS | M0)) /*GPMC_D7*/\
- MUX_VAL(CP(GPMC_D8), (IEN | PTD | DIS | M0)) /*GPMC_D8*/\
- MUX_VAL(CP(GPMC_D9), (IEN | PTD | DIS | M0)) /*GPMC_D9*/\
- MUX_VAL(CP(GPMC_D10), (IEN | PTD | DIS | M0)) /*GPMC_D10*/\
- MUX_VAL(CP(GPMC_D11), (IEN | PTD | DIS | M0)) /*GPMC_D11*/\
- MUX_VAL(CP(GPMC_D12), (IEN | PTD | DIS | M0)) /*GPMC_D12*/\
- MUX_VAL(CP(GPMC_D13), (IEN | PTD | DIS | M0)) /*GPMC_D13*/\
- MUX_VAL(CP(GPMC_D14), (IEN | PTD | DIS | M0)) /*GPMC_D14*/\
- MUX_VAL(CP(GPMC_D15), (IEN | PTD | DIS | M0)) /*GPMC_D15*/\
- MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) /*GPMC_nCS0*/\
- MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M0)) /*GPMC_nCS1*/\
- MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M0)) /*GPMC_nCS2*/\
- MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M0)) /*GPMC_nCS3*/\
- MUX_VAL(CP(GPMC_NCS4), (IDIS | PTU | EN | M0)) /*GPMC_nCS4*/\
- MUX_VAL(CP(GPMC_NCS5), (IDIS | PTD | DIS | M0)) /*GPMC_nCS5*/\
- MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M1)) /*SYS_nDMA_REQ2*/\
- MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M1)) /*SYS_nDMA_REQ3*/\
- MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | DIS | M0)) /*GPMC_nBE1*/\
- MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M0)) /*GPMC_WAIT2*/\
- MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0)) /*GPMC_WAIT3*/\
- MUX_VAL(CP(GPMC_CLK), (IDIS | PTD | DIS | M0)) /*GPMC_CLK*/\
- MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /*GPMC_nADV_ALE*/\
- MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /*GPMC_nOE*/\
- MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /*GPMC_nWE*/\
- MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTD | DIS | M0)) /*GPMC_nBE0_CLE*/\
- MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0)) /*GPMC_nWP*/\
- MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) /*GPMC_WAIT0*/\
- MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) /*GPMC_WAIT1*/\
- /*DSS*/\
- MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
- MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0)) /*DSS_HSYNC*/\
- MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0)) /*DSS_VSYNC*/\
- MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0)) /*DSS_ACBIAS*/\
- MUX_VAL(CP(DSS_DATA0), (IDIS | PTD | DIS | M0)) /*DSS_DATA0*/\
- MUX_VAL(CP(DSS_DATA1), (IDIS | PTD | DIS | M0)) /*DSS_DATA1*/\
- MUX_VAL(CP(DSS_DATA2), (IDIS | PTD | DIS | M0)) /*DSS_DATA2*/\
- MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M0)) /*DSS_DATA3*/\
- MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M0)) /*DSS_DATA4*/\
- MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M0)) /*DSS_DATA5*/\
- MUX_VAL(CP(DSS_DATA6), (IDIS | PTD | DIS | M0)) /*DSS_DATA6*/\
- MUX_VAL(CP(DSS_DATA7), (IDIS | PTD | DIS | M0)) /*DSS_DATA7*/\
- MUX_VAL(CP(DSS_DATA8), (IDIS | PTD | DIS | M0)) /*DSS_DATA8*/\
- MUX_VAL(CP(DSS_DATA9), (IDIS | PTD | DIS | M0)) /*DSS_DATA9*/\
- MUX_VAL(CP(DSS_DATA10), (IDIS | PTD | DIS | M0)) /*DSS_DATA10*/\
- MUX_VAL(CP(DSS_DATA11), (IDIS | PTD | DIS | M0)) /*DSS_DATA11*/\
- MUX_VAL(CP(DSS_DATA12), (IDIS | PTD | DIS | M0)) /*DSS_DATA12*/\
- MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | DIS | M0)) /*DSS_DATA13*/\
- MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | DIS | M0)) /*DSS_DATA14*/\
- MUX_VAL(CP(DSS_DATA15), (IDIS | PTD | DIS | M0)) /*DSS_DATA15*/\
- MUX_VAL(CP(DSS_DATA16), (IDIS | PTD | DIS | M0)) /*DSS_DATA16*/\
- MUX_VAL(CP(DSS_DATA17), (IDIS | PTD | DIS | M0)) /*DSS_DATA17*/\
- MUX_VAL(CP(DSS_DATA18), (IDIS | PTD | DIS | M0)) /*DSS_DATA18*/\
- MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M0)) /*DSS_DATA19*/\
- MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M0)) /*DSS_DATA20*/\
- MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M0)) /*DSS_DATA21*/\
- MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0)) /*DSS_DATA22*/\
- MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0)) /*DSS_DATA23*/\
- /*CAMERA*/\
- MUX_VAL(CP(CAM_HS), (IEN | PTU | EN | M0)) /*CAM_HS */\
- MUX_VAL(CP(CAM_VS), (IEN | PTU | EN | M0)) /*CAM_VS */\
- MUX_VAL(CP(CAM_XCLKA), (IDIS | PTD | DIS | M0)) /*CAM_XCLKA*/\
- MUX_VAL(CP(CAM_PCLK), (IEN | PTU | EN | M0)) /*CAM_PCLK*/\
- MUX_VAL(CP(CAM_FLD), (IDIS | PTD | DIS | M4)) /*GPIO_98*/\
- MUX_VAL(CP(CAM_D0), (IEN | PTD | DIS | M0)) /*CAM_D0*/\
- MUX_VAL(CP(CAM_D1), (IEN | PTD | DIS | M0)) /*CAM_D1*/\
- MUX_VAL(CP(CAM_D2), (IEN | PTD | DIS | M0)) /*CAM_D2*/\
- MUX_VAL(CP(CAM_D3), (IEN | PTD | DIS | M0)) /*CAM_D3*/\
- MUX_VAL(CP(CAM_D4), (IEN | PTD | DIS | M0)) /*CAM_D4*/\
- MUX_VAL(CP(CAM_D5), (IEN | PTD | DIS | M0)) /*CAM_D5*/\
- MUX_VAL(CP(CAM_D6), (IEN | PTD | DIS | M0)) /*CAM_D6*/\
- MUX_VAL(CP(CAM_D7), (IEN | PTD | DIS | M0)) /*CAM_D7*/\
- MUX_VAL(CP(CAM_D8), (IEN | PTD | DIS | M0)) /*CAM_D8*/\
- MUX_VAL(CP(CAM_D9), (IEN | PTD | DIS | M0)) /*CAM_D9*/\
- MUX_VAL(CP(CAM_D10), (IEN | PTD | DIS | M0)) /*CAM_D10*/\
- MUX_VAL(CP(CAM_D11), (IEN | PTD | DIS | M0)) /*CAM_D11*/\
- MUX_VAL(CP(CAM_XCLKB), (IDIS | PTD | DIS | M0)) /*CAM_XCLKB*/\
- MUX_VAL(CP(CAM_WEN), (IEN | PTD | DIS | M4)) /*GPIO_167*/\
- MUX_VAL(CP(CAM_STROBE), (IDIS | PTD | DIS | M0)) /*CAM_STROBE*/\
- MUX_VAL(CP(CSI2_DX0), (IEN | PTD | DIS | M0)) /*CSI2_DX0*/\
- MUX_VAL(CP(CSI2_DY0), (IEN | PTD | DIS | M0)) /*CSI2_DY0*/\
- MUX_VAL(CP(CSI2_DX1), (IEN | PTD | DIS | M0)) /*CSI2_DX1*/\
- MUX_VAL(CP(CSI2_DY1), (IEN | PTD | DIS | M0)) /*CSI2_DY1*/\
- /*Audio Interface */\
- MUX_VAL(CP(MCBSP2_FSX), (IEN | PTD | DIS | M0)) /*McBSP2_FSX*/\
- MUX_VAL(CP(MCBSP2_CLKX), (IEN | PTD | DIS | M0)) /*McBSP2_CLKX*/\
- MUX_VAL(CP(MCBSP2_DR), (IEN | PTD | DIS | M0)) /*McBSP2_DR*/\
- MUX_VAL(CP(MCBSP2_DX), (IDIS | PTD | DIS | M0)) /*McBSP2_DX*/\
- /*Expansion card */\
- MUX_VAL(CP(MMC1_CLK), (IDIS | PTU | EN | M0)) /*MMC1_CLK*/\
- MUX_VAL(CP(MMC1_CMD), (IEN | PTU | EN | M0)) /*MMC1_CMD*/\
- MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | EN | M0)) /*MMC1_DAT0*/\
- MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | EN | M0)) /*MMC1_DAT1*/\
- MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | EN | M0)) /*MMC1_DAT2*/\
- MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | EN | M0)) /*MMC1_DAT3*/\
- MUX_VAL(CP(MMC1_DAT4), (IEN | PTU | EN | M0)) /*MMC1_DAT4*/\
- MUX_VAL(CP(MMC1_DAT5), (IEN | PTU | EN | M0)) /*MMC1_DAT5*/\
- MUX_VAL(CP(MMC1_DAT6), (IEN | PTU | EN | M0)) /*MMC1_DAT6*/\
- MUX_VAL(CP(MMC1_DAT7), (IEN | PTU | EN | M0)) /*MMC1_DAT7*/\
- /*Wireless LAN */\
- MUX_VAL(CP(MMC2_CLK), (IEN | PTU | EN | M4)) /*GPIO_130*/\
- MUX_VAL(CP(MMC2_CMD), (IEN | PTU | EN | M4)) /*GPIO_131*/\
- MUX_VAL(CP(MMC2_DAT0), (IEN | PTU | EN | M4)) /*GPIO_132*/\
- MUX_VAL(CP(MMC2_DAT1), (IEN | PTU | EN | M4)) /*GPIO_133*/\
- MUX_VAL(CP(MMC2_DAT2), (IEN | PTU | EN | M4)) /*GPIO_134*/\
- MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | EN | M4)) /*GPIO_135*/\
- MUX_VAL(CP(MMC2_DAT4), (IEN | PTU | EN | M4)) /*GPIO_136*/\
- MUX_VAL(CP(MMC2_DAT5), (IEN | PTU | EN | M4)) /*GPIO_137*/\
- MUX_VAL(CP(MMC2_DAT6), (IEN | PTU | EN | M4)) /*GPIO_138*/\
- MUX_VAL(CP(MMC2_DAT7), (IEN | PTU | EN | M4)) /*GPIO_139*/\
- /*Bluetooth*/\
- MUX_VAL(CP(MCBSP3_DX), (IEN | PTD | DIS | M1)) /*UART2_CTS*/\
- MUX_VAL(CP(MCBSP3_DR), (IDIS | PTD | DIS | M1)) /*UART2_RTS*/\
- MUX_VAL(CP(MCBSP3_CLKX), (IDIS | PTD | DIS | M1)) /*UART2_TX*/\
- MUX_VAL(CP(MCBSP3_FSX), (IEN | PTD | DIS | M1)) /*UART2_RX*/\
- MUX_VAL(CP(UART2_CTS), (IEN | PTD | DIS | M4)) /*GPIO_144*/\
- MUX_VAL(CP(UART2_RTS), (IEN | PTD | DIS | M4)) /*GPIO_145*/\
- MUX_VAL(CP(UART2_TX), (IEN | PTD | DIS | M4)) /*GPIO_146*/\
- MUX_VAL(CP(UART2_RX), (IEN | PTD | DIS | M4)) /*GPIO_147*/\
- /*Modem Interface */\
- MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0)) /*UART1_TX*/\
- MUX_VAL(CP(UART1_RTS), (IDIS | PTD | DIS | M4)) /*GPIO_149*/ \
- MUX_VAL(CP(UART1_CTS), (IDIS | PTD | DIS | M4)) /*GPIO_150*/ \
- MUX_VAL(CP(UART1_RX), (IEN | PTD | DIS | M0)) /*UART1_RX*/\
- MUX_VAL(CP(MCBSP4_CLKX), (IEN | PTD | DIS | M1)) /*SSI1_DAT_RX*/\
- MUX_VAL(CP(MCBSP4_DR), (IEN | PTD | DIS | M1)) /*SSI1_FLAG_RX*/\
- MUX_VAL(CP(MCBSP4_DX), (IEN | PTD | DIS | M1)) /*SSI1_RDY_RX*/\
- MUX_VAL(CP(MCBSP4_FSX), (IEN | PTD | DIS | M1)) /*SSI1_WAKE*/\
- MUX_VAL(CP(MCBSP1_CLKR), (IDIS | PTD | DIS | M4)) /*GPIO_156*/\
- MUX_VAL(CP(MCBSP1_FSR), (IDIS | PTU | EN | M4)) /*GPIO_157*/\
- MUX_VAL(CP(MCBSP1_DX), (IDIS | PTD | DIS | M4)) /*GPIO_158*/\
- MUX_VAL(CP(MCBSP1_DR), (IDIS | PTD | DIS | M4)) /*GPIO_159*/\
- MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0)) /*McBSP_CLKS*/\
- MUX_VAL(CP(MCBSP1_FSX), (IDIS | PTD | DIS | M4)) /*GPIO_161*/\
- MUX_VAL(CP(MCBSP1_CLKX), (IDIS | PTD | DIS | M4)) /*GPIO_162*/\
- /*Serial Interface*/\
- MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTD | EN | M0)) /*UART3_CTS_RCTX*/\
- MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTD | DIS | M0)) /*UART3_RTS_SD */\
- MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0)) /*UART3_RX_IRRX*/\
- MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0)) /*UART3_TX_IRTX*/\
- MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0)) /*HSUSB0_CLK*/\
- MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0)) /*HSUSB0_STP*/\
- MUX_VAL(CP(HSUSB0_DIR), (IEN | PTD | DIS | M0)) /*HSUSB0_DIR*/\
- MUX_VAL(CP(HSUSB0_NXT), (IEN | PTD | DIS | M0)) /*HSUSB0_NXT*/\
- MUX_VAL(CP(HSUSB0_DATA0), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA0*/\
- MUX_VAL(CP(HSUSB0_DATA1), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA1*/\
- MUX_VAL(CP(HSUSB0_DATA2), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA2*/\
- MUX_VAL(CP(HSUSB0_DATA3), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA3*/\
- MUX_VAL(CP(HSUSB0_DATA4), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA4*/\
- MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA5*/\
- MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA6*/\
- MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA7*/\
- MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)) /*I2C1_SCL*/\
- MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)) /*I2C1_SDA*/\
- MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M4)) /*GPIO_168*/\
- MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M4)) /*GPIO_183*/\
- MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0)) /*I2C3_SCL*/\
- MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0)) /*I2C3_SDA*/\
- MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0)) /*I2C4_SCL*/\
- MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0)) /*I2C4_SDA*/\
- MUX_VAL(CP(HDQ_SIO), (IDIS | PTU | EN | M4)) /*GPIO_170*/\
- MUX_VAL(CP(MCSPI1_CLK), (IEN | PTU | EN | M4)) /*GPIO_171*/\
- MUX_VAL(CP(MCSPI1_SIMO), (IEN | PTU | EN | M4)) /*GPIO_172*/\
- MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | DIS | M0)) /*McSPI1_SOMI*/\
- MUX_VAL(CP(MCSPI1_CS0), (IEN | PTD | EN | M0)) /*McSPI1_CS0*/\
- MUX_VAL(CP(MCSPI1_CS1), (IDIS | PTD | EN | M0)) /*McSPI1_CS1*/\
- MUX_VAL(CP(MCSPI1_CS2), (IDIS | PTD | DIS | M4)) /*GPIO_176*/\
- /* USB EHCI (port 2) */\
- MUX_VAL(CP(MCSPI1_CS3), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA2*/\
- MUX_VAL(CP(MCSPI2_CLK), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA7*/\
- MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA4*/\
- MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA5*/\
- MUX_VAL(CP(MCSPI2_CS0), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA6*/\
- MUX_VAL(CP(MCSPI2_CS1), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA3*/\
- MUX_VAL(CP(ETK_D10_ES2), (IDIS | PTU | DIS | M3)) /*HSUSB2_CLK*/\
- MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTU | DIS | M3)) /*HSUSB2_STP*/\
- MUX_VAL(CP(ETK_D12_ES2), (IEN | PTU | DIS | M3)) /*HSUSB2_DIR*/\
- MUX_VAL(CP(ETK_D13_ES2), (IEN | PTU | DIS | M3)) /*HSUSB2_NXT*/\
- MUX_VAL(CP(ETK_D14_ES2), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA0*/\
- MUX_VAL(CP(ETK_D15_ES2), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA1*/\
- /*Control and debug */\
- MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0)) /*SYS_32K*/\
- MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) /*SYS_CLKREQ*/\
- MUX_VAL(CP(SYS_NIRQ), (IEN | PTU | EN | M0)) /*SYS_nIRQ*/\
- MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4)) /*GPIO_2*/\
- MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4)) /*GPIO_3*/\
- MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /*GPIO_4 - MMC1_WP*/\
- MUX_VAL(CP(SYS_BOOT3), (IEN | PTD | DIS | M4)) /*GPIO_5*/\
- MUX_VAL(CP(SYS_BOOT4), (IEN | PTD | DIS | M4)) /*GPIO_6*/\
- MUX_VAL(CP(SYS_BOOT5), (IEN | PTD | DIS | M4)) /*GPIO_7*/\
- MUX_VAL(CP(SYS_BOOT6), (IDIS | PTD | DIS | M4)) /*GPIO_8*/ \
- MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0)) /*SYS_OFF_MODE*/\
- MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M0)) /*SYS_CLKOUT1*/\
- MUX_VAL(CP(SYS_CLKOUT2), (IEN | PTU | EN | M4)) /*GPIO_186*/\
- MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | EN | M3)) /*HSUSB1_STP*/\
- MUX_VAL(CP(ETK_CTL_ES2), (IDIS | PTU | DIS | M3)) /*HSUSB1_CLK*/\
- MUX_VAL(CP(ETK_D0_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA0*/\
- MUX_VAL(CP(ETK_D1_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA1*/\
- MUX_VAL(CP(ETK_D2_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA2*/\
- MUX_VAL(CP(ETK_D3_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA7*/\
- MUX_VAL(CP(ETK_D4_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA4*/\
- MUX_VAL(CP(ETK_D5_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA5*/\
- MUX_VAL(CP(ETK_D6_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA6*/\
- MUX_VAL(CP(ETK_D7_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA3*/\
- MUX_VAL(CP(ETK_D8_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DIR*/\
- MUX_VAL(CP(ETK_D9_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_NXT*/\
- MUX_VAL(CP(D2D_MCAD1), (IEN | PTD | EN | M0)) /*d2d_mcad1*/\
- MUX_VAL(CP(D2D_MCAD2), (IEN | PTD | EN | M0)) /*d2d_mcad2*/\
- MUX_VAL(CP(D2D_MCAD3), (IEN | PTD | EN | M0)) /*d2d_mcad3*/\
- MUX_VAL(CP(D2D_MCAD4), (IEN | PTD | EN | M0)) /*d2d_mcad4*/\
- MUX_VAL(CP(D2D_MCAD5), (IEN | PTD | EN | M0)) /*d2d_mcad5*/\
- MUX_VAL(CP(D2D_MCAD6), (IEN | PTD | EN | M0)) /*d2d_mcad6*/\
- MUX_VAL(CP(D2D_MCAD7), (IEN | PTD | EN | M0)) /*d2d_mcad7*/\
- MUX_VAL(CP(D2D_MCAD8), (IEN | PTD | EN | M0)) /*d2d_mcad8*/\
- MUX_VAL(CP(D2D_MCAD9), (IEN | PTD | EN | M0)) /*d2d_mcad9*/\
- MUX_VAL(CP(D2D_MCAD10), (IEN | PTD | EN | M0)) /*d2d_mcad10*/\
- MUX_VAL(CP(D2D_MCAD11), (IEN | PTD | EN | M0)) /*d2d_mcad11*/\
- MUX_VAL(CP(D2D_MCAD12), (IEN | PTD | EN | M0)) /*d2d_mcad12*/\
- MUX_VAL(CP(D2D_MCAD13), (IEN | PTD | EN | M0)) /*d2d_mcad13*/\
- MUX_VAL(CP(D2D_MCAD14), (IEN | PTD | EN | M0)) /*d2d_mcad14*/\
- MUX_VAL(CP(D2D_MCAD15), (IEN | PTD | EN | M0)) /*d2d_mcad15*/\
- MUX_VAL(CP(D2D_MCAD16), (IEN | PTD | EN | M0)) /*d2d_mcad16*/\
- MUX_VAL(CP(D2D_MCAD17), (IEN | PTD | EN | M0)) /*d2d_mcad17*/\
- MUX_VAL(CP(D2D_MCAD18), (IEN | PTD | EN | M0)) /*d2d_mcad18*/\
- MUX_VAL(CP(D2D_MCAD19), (IEN | PTD | EN | M0)) /*d2d_mcad19*/\
- MUX_VAL(CP(D2D_MCAD20), (IEN | PTD | EN | M0)) /*d2d_mcad20*/\
- MUX_VAL(CP(D2D_MCAD21), (IEN | PTD | EN | M0)) /*d2d_mcad21*/\
- MUX_VAL(CP(D2D_MCAD22), (IEN | PTD | EN | M0)) /*d2d_mcad22*/\
- MUX_VAL(CP(D2D_MCAD23), (IEN | PTD | EN | M0)) /*d2d_mcad23*/\
- MUX_VAL(CP(D2D_MCAD24), (IEN | PTD | EN | M0)) /*d2d_mcad24*/\
- MUX_VAL(CP(D2D_MCAD25), (IEN | PTD | EN | M0)) /*d2d_mcad25*/\
- MUX_VAL(CP(D2D_MCAD26), (IEN | PTD | EN | M0)) /*d2d_mcad26*/\
- MUX_VAL(CP(D2D_MCAD27), (IEN | PTD | EN | M0)) /*d2d_mcad27*/\
- MUX_VAL(CP(D2D_MCAD28), (IEN | PTD | EN | M0)) /*d2d_mcad28*/\
- MUX_VAL(CP(D2D_MCAD29), (IEN | PTD | EN | M0)) /*d2d_mcad29*/\
- MUX_VAL(CP(D2D_MCAD30), (IEN | PTD | EN | M0)) /*d2d_mcad30*/\
- MUX_VAL(CP(D2D_MCAD31), (IEN | PTD | EN | M0)) /*d2d_mcad31*/\
- MUX_VAL(CP(D2D_MCAD32), (IEN | PTD | EN | M0)) /*d2d_mcad32*/\
- MUX_VAL(CP(D2D_MCAD33), (IEN | PTD | EN | M0)) /*d2d_mcad33*/\
- MUX_VAL(CP(D2D_MCAD34), (IEN | PTD | EN | M0)) /*d2d_mcad34*/\
- MUX_VAL(CP(D2D_MCAD35), (IEN | PTD | EN | M0)) /*d2d_mcad35*/\
- MUX_VAL(CP(D2D_MCAD36), (IEN | PTD | EN | M0)) /*d2d_mcad36*/\
- MUX_VAL(CP(D2D_CLK26MI), (IEN | PTD | DIS | M0)) /*d2d_clk26mi*/\
- MUX_VAL(CP(D2D_NRESPWRON), (IEN | PTD | EN | M0)) /*d2d_nrespwron*/\
- MUX_VAL(CP(D2D_NRESWARM), (IEN | PTU | EN | M0)) /*d2d_nreswarm */\
- MUX_VAL(CP(D2D_ARM9NIRQ), (IEN | PTD | DIS | M0)) /*d2d_arm9nirq */\
- MUX_VAL(CP(D2D_UMA2P6FIQ), (IEN | PTD | DIS | M0)) /*d2d_uma2p6fiq*/\
- MUX_VAL(CP(D2D_SPINT), (IEN | PTD | EN | M0)) /*d2d_spint*/\
- MUX_VAL(CP(D2D_FRINT), (IEN | PTD | EN | M0)) /*d2d_frint*/\
- MUX_VAL(CP(D2D_DMAREQ0), (IEN | PTD | DIS | M0)) /*d2d_dmareq0*/\
- MUX_VAL(CP(D2D_DMAREQ1), (IEN | PTD | DIS | M0)) /*d2d_dmareq1*/\
- MUX_VAL(CP(D2D_DMAREQ2), (IEN | PTD | DIS | M0)) /*d2d_dmareq2*/\
- MUX_VAL(CP(D2D_DMAREQ3), (IEN | PTD | DIS | M0)) /*d2d_dmareq3*/\
- MUX_VAL(CP(D2D_N3GTRST), (IEN | PTD | DIS | M0)) /*d2d_n3gtrst*/\
- MUX_VAL(CP(D2D_N3GTDI), (IEN | PTD | DIS | M0)) /*d2d_n3gtdi*/\
- MUX_VAL(CP(D2D_N3GTDO), (IEN | PTD | DIS | M0)) /*d2d_n3gtdo*/\
- MUX_VAL(CP(D2D_N3GTMS), (IEN | PTD | DIS | M0)) /*d2d_n3gtms*/\
- MUX_VAL(CP(D2D_N3GTCK), (IEN | PTD | DIS | M0)) /*d2d_n3gtck*/\
- MUX_VAL(CP(D2D_N3GRTCK), (IEN | PTD | DIS | M0)) /*d2d_n3grtck*/\
- MUX_VAL(CP(D2D_MSTDBY), (IEN | PTU | EN | M0)) /*d2d_mstdby*/\
- MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0)) /*d2d_swakeup*/\
- MUX_VAL(CP(D2D_IDLEREQ), (IEN | PTD | DIS | M0)) /*d2d_idlereq*/\
- MUX_VAL(CP(D2D_IDLEACK), (IEN | PTU | EN | M0)) /*d2d_idleack*/\
- MUX_VAL(CP(D2D_MWRITE), (IEN | PTD | DIS | M0)) /*d2d_mwrite*/\
- MUX_VAL(CP(D2D_SWRITE), (IEN | PTD | DIS | M0)) /*d2d_swrite*/\
- MUX_VAL(CP(D2D_MREAD), (IEN | PTD | DIS | M0)) /*d2d_mread*/\
- MUX_VAL(CP(D2D_SREAD), (IEN | PTD | DIS | M0)) /*d2d_sread*/\
- MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_mbusflag*/\
- MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_sbusflag*/\
- MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0)) /*sdrc_cke0*/\
- MUX_VAL(CP(SDRC_CKE1), (IDIS | PTU | EN | M0)) /*sdrc_cke1*/
-
-#define MUX_BEAGLE_C() \
- MUX_VAL(CP(MCBSP3_DX), (IEN | PTD | DIS | M4)) /*GPIO_140*/\
- MUX_VAL(CP(MCBSP3_DR), (IEN | PTD | DIS | M4)) /*GPIO_142*/\
- MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTD | DIS | M4)) /*GPIO_141*/\
- MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M0)) /*UART2_CTS*/\
- MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M0)) /*UART2_RTS*/\
- MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M0)) /*UART2_TX*/
-
-#endif
+++ /dev/null
-#
-# (C) Copyright 2006
-# Texas Instruments, <www.ti.com>
-#
-# Beagle Board uses OMAP3 (ARM-CortexA8) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-# Physical Address:
-# 8000'0000 (bank0)
-# A000/0000 (bank1)
-# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
-# (mem base + reserved)
-
-# For use with external or internal boots.
-TEXT_BASE = 0x80e80000
+++ /dev/null
-#
-# (C) Copyright 2000, 2001, 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = $(obj)lib$(BOARD).a
-
-COBJS := evm.o
-
-SRCS := $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-
-$(LIB): $(obj).depend $(OBJS)
- $(AR) $(ARFLAGS) $@ $(OBJS)
-
-clean:
- rm -f $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
+++ /dev/null
-#
-# (C) Copyright 2006 - 2008
-# Texas Instruments, <www.ti.com>
-#
-# EVM uses OMAP3 (ARM-CortexA8) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-# Physical Address:
-# 8000'0000 (bank0)
-# A000/0000 (bank1)
-# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
-# (mem base + reserved)
-
-# For use with external or internal boots.
-TEXT_BASE = 0x80e80000
+++ /dev/null
-/*
- * (C) Copyright 2004-2008
- * Texas Instruments, <www.ti.com>
- *
- * Author :
- * Manikandan Pillai <mani.pillai@ti.com>
- *
- * Derived from Beagle Board and 3430 SDP code by
- * Richard Woodruff <r-woodruff2@ti.com>
- * Syed Mohammed Khasim <khasim@ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#include <common.h>
-#include <netdev.h>
-#include <asm/io.h>
-#include <asm/arch/mem.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/sys_proto.h>
-#include <i2c.h>
-#include <asm/mach-types.h>
-#include "evm.h"
-
-/*
- * Routine: board_init
- * Description: Early hardware init.
- */
-int board_init(void)
-{
- DECLARE_GLOBAL_DATA_PTR;
-
- gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
- /* board id for Linux */
- gd->bd->bi_arch_number = MACH_TYPE_OMAP3EVM;
- /* boot param addr */
- gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
-
- return 0;
-}
-
-/*
- * Routine: misc_init_r
- * Description: Init ethernet (done here so udelay works)
- */
-int misc_init_r(void)
-{
-
-#ifdef CONFIG_DRIVER_OMAP34XX_I2C
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-#endif
-
-#if defined(CONFIG_CMD_NET)
- setup_net_chip();
-#endif
-
- dieid_num_r();
-
- return 0;
-}
-
-/*
- * Routine: set_muxconf_regs
- * Description: Setting up the configuration Mux registers specific to the
- * hardware. Many pins need to be moved from protect to primary
- * mode.
- */
-void set_muxconf_regs(void)
-{
- MUX_EVM();
-}
-
-/*
- * Routine: setup_net_chip
- * Description: Setting up the configuration GPMC registers specific to the
- * Ethernet hardware.
- */
-static void setup_net_chip(void)
-{
- struct gpio *gpio3_base = (struct gpio *)OMAP34XX_GPIO3_BASE;
- struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE;
-
- /* Configure GPMC registers */
- writel(NET_GPMC_CONFIG1, &gpmc_cfg->cs[5].config1);
- writel(NET_GPMC_CONFIG2, &gpmc_cfg->cs[5].config2);
- writel(NET_GPMC_CONFIG3, &gpmc_cfg->cs[5].config3);
- writel(NET_GPMC_CONFIG4, &gpmc_cfg->cs[5].config4);
- writel(NET_GPMC_CONFIG5, &gpmc_cfg->cs[5].config5);
- writel(NET_GPMC_CONFIG6, &gpmc_cfg->cs[5].config6);
- writel(NET_GPMC_CONFIG7, &gpmc_cfg->cs[5].config7);
-
- /* Enable off mode for NWE in PADCONF_GPMC_NWE register */
- writew(readw(&ctrl_base ->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe);
- /* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */
- writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe);
- /* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */
- writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00,
- &ctrl_base->gpmc_nadv_ale);
-
- /* Make GPIO 64 as output pin */
- writel(readl(&gpio3_base->oe) & ~(GPIO0), &gpio3_base->oe);
-
- /* Now send a pulse on the GPIO pin */
- writel(GPIO0, &gpio3_base->setdataout);
- udelay(1);
- writel(GPIO0, &gpio3_base->cleardataout);
- udelay(1);
- writel(GPIO0, &gpio3_base->setdataout);
-}
-
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_SMC911X
- rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
-#endif
- return rc;
-}
+++ /dev/null
-/*
- * (C) Copyright 2008
- * Nishanth Menon <menon.nishanth@gmail.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#ifndef _EVM_H_
-#define _EVM_H_
-
-const omap3_sysinfo sysinfo = {
- DDR_DISCRETE,
- "OMAP3 EVM board",
-#if defined(CONFIG_ENV_IS_IN_ONENAND)
- "OneNAND",
-#else
- "NAND",
-#endif
-};
-
-static void setup_net_chip(void);
-
-/*
- * IEN - Input Enable
- * IDIS - Input Disable
- * PTD - Pull type Down
- * PTU - Pull type Up
- * DIS - Pull type selection is inactive
- * EN - Pull type selection is active
- * M0 - Mode 0
- * The commented string gives the final mux configuration for that pin
- */
-#define MUX_EVM() \
- /*SDRC*/\
- MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) /*SDRC_D0*/\
- MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) /*SDRC_D1*/\
- MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) /*SDRC_D2*/\
- MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) /*SDRC_D3*/\
- MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) /*SDRC_D4*/\
- MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) /*SDRC_D5*/\
- MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) /*SDRC_D6*/\
- MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) /*SDRC_D7*/\
- MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) /*SDRC_D8*/\
- MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) /*SDRC_D9*/\
- MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) /*SDRC_D10*/\
- MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) /*SDRC_D11*/\
- MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) /*SDRC_D12*/\
- MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) /*SDRC_D13*/\
- MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) /*SDRC_D14*/\
- MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) /*SDRC_D15*/\
- MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) /*SDRC_D16*/\
- MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) /*SDRC_D17*/\
- MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) /*SDRC_D18*/\
- MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) /*SDRC_D19*/\
- MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) /*SDRC_D20*/\
- MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) /*SDRC_D21*/\
- MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) /*SDRC_D22*/\
- MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) /*SDRC_D23*/\
- MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) /*SDRC_D24*/\
- MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) /*SDRC_D25*/\
- MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) /*SDRC_D26*/\
- MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) /*SDRC_D27*/\
- MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) /*SDRC_D28*/\
- MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) /*SDRC_D29*/\
- MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) /*SDRC_D30*/\
- MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) /*SDRC_D31*/\
- MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) /*SDRC_CLK*/\
- MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) /*SDRC_DQS0*/\
- MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) /*SDRC_DQS1*/\
- MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) /*SDRC_DQS2*/\
- MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) /*SDRC_DQS3*/\
- /*GPMC*/\
- MUX_VAL(CP(GPMC_A1), (IDIS | PTU | EN | M0)) /*GPMC_A1*/\
- MUX_VAL(CP(GPMC_A2), (IDIS | PTU | EN | M0)) /*GPMC_A2*/\
- MUX_VAL(CP(GPMC_A3), (IDIS | PTU | EN | M0)) /*GPMC_A3*/\
- MUX_VAL(CP(GPMC_A4), (IDIS | PTU | EN | M0)) /*GPMC_A4*/\
- MUX_VAL(CP(GPMC_A5), (IDIS | PTU | EN | M0)) /*GPMC_A5*/\
- MUX_VAL(CP(GPMC_A6), (IDIS | PTU | EN | M0)) /*GPMC_A6*/\
- MUX_VAL(CP(GPMC_A7), (IDIS | PTU | EN | M0)) /*GPMC_A7*/\
- MUX_VAL(CP(GPMC_A8), (IDIS | PTU | EN | M0)) /*GPMC_A8*/\
- MUX_VAL(CP(GPMC_A9), (IDIS | PTU | EN | M0)) /*GPMC_A9*/\
- MUX_VAL(CP(GPMC_A10), (IDIS | PTU | EN | M0)) /*GPMC_A10*/\
- MUX_VAL(CP(GPMC_D0), (IEN | PTU | EN | M0)) /*GPMC_D0*/\
- MUX_VAL(CP(GPMC_D1), (IEN | PTU | EN | M0)) /*GPMC_D1*/\
- MUX_VAL(CP(GPMC_D2), (IEN | PTU | EN | M0)) /*GPMC_D2*/\
- MUX_VAL(CP(GPMC_D3), (IEN | PTU | EN | M0)) /*GPMC_D3*/\
- MUX_VAL(CP(GPMC_D4), (IEN | PTU | EN | M0)) /*GPMC_D4*/\
- MUX_VAL(CP(GPMC_D5), (IEN | PTU | EN | M0)) /*GPMC_D5*/\
- MUX_VAL(CP(GPMC_D6), (IEN | PTU | EN | M0)) /*GPMC_D6*/\
- MUX_VAL(CP(GPMC_D7), (IEN | PTU | EN | M0)) /*GPMC_D7*/\
- MUX_VAL(CP(GPMC_D8), (IEN | PTU | EN | M0)) /*GPMC_D8*/\
- MUX_VAL(CP(GPMC_D9), (IEN | PTU | EN | M0)) /*GPMC_D9*/\
- MUX_VAL(CP(GPMC_D10), (IEN | PTU | EN | M0)) /*GPMC_D10*/\
- MUX_VAL(CP(GPMC_D11), (IEN | PTU | EN | M0)) /*GPMC_D11*/\
- MUX_VAL(CP(GPMC_D12), (IEN | PTU | EN | M0)) /*GPMC_D12*/\
- MUX_VAL(CP(GPMC_D13), (IEN | PTU | EN | M0)) /*GPMC_D13*/\
- MUX_VAL(CP(GPMC_D14), (IEN | PTU | EN | M0)) /*GPMC_D14*/\
- MUX_VAL(CP(GPMC_D15), (IEN | PTU | EN | M0)) /*GPMC_D15*/\
- MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) /*GPMC_nCS0*/\
- MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M0)) /*GPMC_nCS1*/\
- MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M0)) /*GPMC_nCS2*/\
- MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M0)) /*GPMC_nCS3*/\
- MUX_VAL(CP(GPMC_NCS4), (IEN | PTU | EN | M0)) /*GPMC_nCS4*/\
- MUX_VAL(CP(GPMC_NCS5), (IDIS | PTU | EN | M0)) /*GPMC_nCS5*/\
- MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M0)) /*GPMC_nCS6*/\
- MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M0)) /*GPMC_nCS7*/\
- MUX_VAL(CP(GPMC_CLK), (IDIS | PTU | EN | M0)) /*GPMC_CLK*/\
- MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /*GPMC_nADV_ALE*/\
- MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /*GPMC_nOE*/\
- MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /*GPMC_nWE*/\
- MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTU | EN | M0)) /*GPMC_nBE0_CLE*/\
- MUX_VAL(CP(GPMC_NBE1), (IEN | PTU | EN | M0)) /*GPMC_nBE1*/\
- MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0)) /*GPMC_nWP*/\
- MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) /*GPMC_WAIT0*/\
- MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) /*GPMC_WAIT1*/\
- MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M4)) /*GPIO_64*/\
- /* - ETH_nRESET*/\
- MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0)) /*GPMC_WAIT3*/\
- /*DSS*/\
- MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
- MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0)) /*DSS_HSYNC*/\
- MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0)) /*DSS_VSYNC*/\
- MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0)) /*DSS_ACBIAS*/\
- MUX_VAL(CP(DSS_DATA0), (IDIS | PTD | DIS | M0)) /*DSS_DATA0*/\
- MUX_VAL(CP(DSS_DATA1), (IDIS | PTD | DIS | M0)) /*DSS_DATA1*/\
- MUX_VAL(CP(DSS_DATA2), (IDIS | PTD | DIS | M0)) /*DSS_DATA2*/\
- MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M0)) /*DSS_DATA3*/\
- MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M0)) /*DSS_DATA4*/\
- MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M0)) /*DSS_DATA5*/\
- MUX_VAL(CP(DSS_DATA6), (IDIS | PTD | DIS | M0)) /*DSS_DATA6*/\
- MUX_VAL(CP(DSS_DATA7), (IDIS | PTD | DIS | M0)) /*DSS_DATA7*/\
- MUX_VAL(CP(DSS_DATA8), (IDIS | PTD | DIS | M0)) /*DSS_DATA8*/\
- MUX_VAL(CP(DSS_DATA9), (IDIS | PTD | DIS | M0)) /*DSS_DATA9*/\
- MUX_VAL(CP(DSS_DATA10), (IDIS | PTD | DIS | M0)) /*DSS_DATA10*/\
- MUX_VAL(CP(DSS_DATA11), (IDIS | PTD | DIS | M0)) /*DSS_DATA11*/\
- MUX_VAL(CP(DSS_DATA12), (IDIS | PTD | DIS | M0)) /*DSS_DATA12*/\
- MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | DIS | M0)) /*DSS_DATA13*/\
- MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | DIS | M0)) /*DSS_DATA14*/\
- MUX_VAL(CP(DSS_DATA15), (IDIS | PTD | DIS | M0)) /*DSS_DATA15*/\
- MUX_VAL(CP(DSS_DATA16), (IDIS | PTD | DIS | M0)) /*DSS_DATA16*/\
- MUX_VAL(CP(DSS_DATA17), (IDIS | PTD | DIS | M0)) /*DSS_DATA17*/\
- MUX_VAL(CP(DSS_DATA18), (IDIS | PTD | DIS | M0)) /*DSS_DATA18*/\
- MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M0)) /*DSS_DATA19*/\
- MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M0)) /*DSS_DATA20*/\
- MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M0)) /*DSS_DATA21*/\
- MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0)) /*DSS_DATA22*/\
- MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0)) /*DSS_DATA23*/\
- /*CAMERA*/\
- MUX_VAL(CP(CAM_HS), (IEN | PTU | EN | M0)) /*CAM_HS */\
- MUX_VAL(CP(CAM_VS), (IEN | PTU | EN | M0)) /*CAM_VS */\
- MUX_VAL(CP(CAM_XCLKA), (IDIS | PTD | DIS | M0)) /*CAM_XCLKA*/\
- MUX_VAL(CP(CAM_PCLK), (IEN | PTU | EN | M0)) /*CAM_PCLK*/\
- MUX_VAL(CP(CAM_FLD), (IDIS | PTD | DIS | M4)) /*GPIO_98*/\
- /* - CAM_RESET*/\
- MUX_VAL(CP(CAM_D0), (IEN | PTD | DIS | M0)) /*CAM_D0*/\
- MUX_VAL(CP(CAM_D1), (IEN | PTD | DIS | M0)) /*CAM_D1*/\
- MUX_VAL(CP(CAM_D2), (IEN | PTD | DIS | M0)) /*CAM_D2*/\
- MUX_VAL(CP(CAM_D3), (IEN | PTD | DIS | M0)) /*CAM_D3*/\
- MUX_VAL(CP(CAM_D4), (IEN | PTD | DIS | M0)) /*CAM_D4*/\
- MUX_VAL(CP(CAM_D5), (IEN | PTD | DIS | M0)) /*CAM_D5*/\
- MUX_VAL(CP(CAM_D6), (IEN | PTD | DIS | M0)) /*CAM_D6*/\
- MUX_VAL(CP(CAM_D7), (IEN | PTD | DIS | M0)) /*CAM_D7*/\
- MUX_VAL(CP(CAM_D8), (IEN | PTD | DIS | M0)) /*CAM_D8*/\
- MUX_VAL(CP(CAM_D9), (IEN | PTD | DIS | M0)) /*CAM_D9*/\
- MUX_VAL(CP(CAM_D10), (IEN | PTD | DIS | M0)) /*CAM_D10*/\
- MUX_VAL(CP(CAM_D11), (IEN | PTD | DIS | M0)) /*CAM_D11*/\
- MUX_VAL(CP(CAM_XCLKB), (IDIS | PTD | DIS | M0)) /*CAM_XCLKB*/\
- MUX_VAL(CP(CAM_WEN), (IEN | PTD | DIS | M4)) /*GPIO_167*/\
- MUX_VAL(CP(CAM_STROBE), (IDIS | PTD | DIS | M0)) /*CAM_STROBE*/\
- MUX_VAL(CP(CSI2_DX0), (IEN | PTD | DIS | M0)) /*CSI2_DX0*/\
- MUX_VAL(CP(CSI2_DY0), (IEN | PTD | DIS | M0)) /*CSI2_DY0*/\
- MUX_VAL(CP(CSI2_DX1), (IEN | PTD | DIS | M0)) /*CSI2_DX1*/\
- MUX_VAL(CP(CSI2_DY1), (IEN | PTD | DIS | M0)) /*CSI2_DY1*/\
- /*Audio Interface */\
- MUX_VAL(CP(MCBSP2_FSX), (IEN | PTD | DIS | M0)) /*McBSP2_FSX*/\
- MUX_VAL(CP(MCBSP2_CLKX), (IEN | PTD | DIS | M0)) /*McBSP2_CLKX*/\
- MUX_VAL(CP(MCBSP2_DR), (IEN | PTD | DIS | M0)) /*McBSP2_DR*/\
- MUX_VAL(CP(MCBSP2_DX), (IDIS | PTD | DIS | M0)) /*McBSP2_DX*/\
- /*Expansion card */\
- MUX_VAL(CP(MMC1_CLK), (IDIS | PTU | EN | M0)) /*MMC1_CLK*/\
- MUX_VAL(CP(MMC1_CMD), (IEN | PTU | EN | M0)) /*MMC1_CMD*/\
- MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | EN | M0)) /*MMC1_DAT0*/\
- MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | EN | M0)) /*MMC1_DAT1*/\
- MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | EN | M0)) /*MMC1_DAT2*/\
- MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | EN | M0)) /*MMC1_DAT3*/\
- MUX_VAL(CP(MMC1_DAT4), (IEN | PTU | EN | M0)) /*MMC1_DAT4*/\
- MUX_VAL(CP(MMC1_DAT5), (IEN | PTU | EN | M0)) /*MMC1_DAT5*/\
- MUX_VAL(CP(MMC1_DAT6), (IEN | PTU | EN | M0)) /*MMC1_DAT6*/\
- MUX_VAL(CP(MMC1_DAT7), (IEN | PTU | EN | M0)) /*MMC1_DAT7*/\
- /*Wireless LAN */\
- MUX_VAL(CP(MMC2_CLK), (IEN | PTD | DIS | M0)) /*MMC2_CLK*/\
- MUX_VAL(CP(MMC2_CMD), (IEN | PTU | EN | M0)) /*MMC2_CMD*/\
- MUX_VAL(CP(MMC2_DAT0), (IEN | PTU | EN | M0)) /*MMC2_DAT0*/\
- MUX_VAL(CP(MMC2_DAT1), (IEN | PTU | EN | M0)) /*MMC2_DAT1*/\
- MUX_VAL(CP(MMC2_DAT2), (IEN | PTU | EN | M0)) /*MMC2_DAT2*/\
- MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | EN | M0)) /*MMC2_DAT3*/\
- MUX_VAL(CP(MMC2_DAT4), (IDIS | PTD | DIS | M0)) /*MMC2_DAT4*/\
- MUX_VAL(CP(MMC2_DAT5), (IDIS | PTD | DIS | M0)) /*MMC2_DAT5*/\
- MUX_VAL(CP(MMC2_DAT6), (IDIS | PTD | DIS | M0)) /*MMC2_DAT6 */\
- MUX_VAL(CP(MMC2_DAT7), (IEN | PTU | EN | M0)) /*MMC2_DAT7*/\
- /*Bluetooth*/\
- MUX_VAL(CP(MCBSP3_DX), (IDIS | PTD | DIS | M0)) /*McBSP3_DX*/\
- MUX_VAL(CP(MCBSP3_DR), (IEN | PTD | DIS | M0)) /*McBSP3_DR*/\
- MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTD | DIS | M0)) /*McBSP3_CLKX */\
- MUX_VAL(CP(MCBSP3_FSX), (IEN | PTD | DIS | M0)) /*McBSP3_FSX*/\
- MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M0)) /*UART2_CTS*/\
- MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M0)) /*UART2_RTS*/\
- MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M0)) /*UART2_TX*/\
- MUX_VAL(CP(UART2_RX), (IEN | PTD | DIS | M0)) /*UART2_RX*/\
- /*Modem Interface */\
- MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0)) /*UART1_TX*/\
- MUX_VAL(CP(UART1_RTS), (IDIS | PTD | DIS | M0)) /*UART1_RTS*/\
- MUX_VAL(CP(UART1_CTS), (IEN | PTU | DIS | M0)) /*UART1_CTS*/\
- MUX_VAL(CP(UART1_RX), (IEN | PTD | DIS | M0)) /*UART1_RX*/\
- MUX_VAL(CP(MCBSP4_CLKX), (IDIS | PTD | DIS | M4)) /*GPIO_152*/\
- /* - LCD_INI*/\
- MUX_VAL(CP(MCBSP4_DR), (IDIS | PTD | DIS | M4)) /*GPIO_153*/\
- /* - LCD_ENVDD */\
- MUX_VAL(CP(MCBSP4_DX), (IDIS | PTD | DIS | M4)) /*GPIO_154*/\
- /* - LCD_QVGA/nVGA */\
- MUX_VAL(CP(MCBSP4_FSX), (IDIS | PTD | DIS | M4)) /*GPIO_155*/\
- /* - LCD_RESB */\
- MUX_VAL(CP(MCBSP1_CLKR), (IEN | PTD | DIS | M0)) /*MCBSP1_CLKR */\
- MUX_VAL(CP(MCBSP1_FSR), (IDIS | PTU | EN | M0)) /*MCBSP1_FSR*/\
- MUX_VAL(CP(MCBSP1_DX), (IDIS | PTD | DIS | M0)) /*MCBSP1_DX*/\
- MUX_VAL(CP(MCBSP1_DR), (IEN | PTD | DIS | M0)) /*MCBSP1_DR*/\
- MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0)) /*MCBSP_CLKS */\
- MUX_VAL(CP(MCBSP1_FSX), (IEN | PTD | DIS | M0)) /*MCBSP1_FSX*/\
- MUX_VAL(CP(MCBSP1_CLKX), (IEN | PTD | DIS | M0)) /*MCBSP1_CLKX */\
- /*Serial Interface*/\
- MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTD | EN | M0)) /*UART3_CTS_*/\
- /* RCTX*/\
- MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTD | DIS | M0)) /*UART3_RTS_SD */\
- MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0)) /*UART3_RX_IRRX*/\
- MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0)) /*UART3_TX_IRTX*/\
- MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0)) /*HSUSB0_CLK*/\
- MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0)) /*HSUSB0_STP*/\
- MUX_VAL(CP(HSUSB0_DIR), (IEN | PTD | DIS | M0)) /*HSUSB0_DIR*/\
- MUX_VAL(CP(HSUSB0_NXT), (IEN | PTD | DIS | M0)) /*HSUSB0_NXT*/\
- MUX_VAL(CP(HSUSB0_DATA0), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA0*/\
- MUX_VAL(CP(HSUSB0_DATA1), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA1*/\
- MUX_VAL(CP(HSUSB0_DATA2), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA2*/\
- MUX_VAL(CP(HSUSB0_DATA3), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA3*/\
- MUX_VAL(CP(HSUSB0_DATA4), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA4*/\
- MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA5*/\
- MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA6*/\
- MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA7*/\
- MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)) /*I2C1_SCL*/\
- MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)) /*I2C1_SDA*/\
- MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M0)) /*I2C2_SCL*/\
- MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M0)) /*I2C2_SDA*/\
- MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0)) /*I2C3_SCL*/\
- MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0)) /*I2C3_SDA*/\
- MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0)) /*I2C4_SCL*/\
- MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0)) /*I2C4_SDA*/\
- MUX_VAL(CP(HDQ_SIO), (IEN | PTU | EN | M0)) /*HDQ_SIO*/\
- MUX_VAL(CP(MCSPI1_CLK), (IEN | PTD | DIS | M0)) /*McSPI1_CLK*/\
- MUX_VAL(CP(MCSPI1_SIMO), (IEN | PTD | DIS | M0)) /*McSPI1_SIMO */\
- MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | DIS | M0)) /*McSPI1_SOMI */\
- MUX_VAL(CP(MCSPI1_CS0), (IEN | PTD | EN | M0)) /*McSPI1_CS0*/\
- MUX_VAL(CP(MCSPI1_CS1), (IEN | PTD | EN | M4)) /*GPIO_175*/\
- /* TS_PEN_IRQ */\
- MUX_VAL(CP(MCSPI1_CS2), (IEN | PTU | DIS | M4)) /*GPIO_176*/\
- /* - LAN_INTR*/\
- MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | EN | M0)) /*McSPI1_CS3*/\
- MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | DIS | M0)) /*McSPI2_CLK*/\
- MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | DIS | M0)) /*McSPI2_SIMO*/\
- MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | DIS | M0)) /*McSPI2_SOMI*/\
- MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | EN | M0)) /*McSPI2_CS0*/\
- MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | EN | M0)) /*McSPI2_CS1*/\
- /*Control and debug */\
- MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0)) /*SYS_32K*/\
- MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) /*SYS_CLKREQ*/\
- MUX_VAL(CP(SYS_NIRQ), (IEN | PTU | EN | M0)) /*SYS_nIRQ*/\
- MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4)) /*GPIO_2*/\
- /* - PEN_IRQ */\
- MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4)) /*GPIO_3 */\
- MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /*GPIO_4*/\
- MUX_VAL(CP(SYS_BOOT3), (IEN | PTD | DIS | M4)) /*GPIO_5*/\
- MUX_VAL(CP(SYS_BOOT4), (IEN | PTD | DIS | M4)) /*GPIO_6*/\
- MUX_VAL(CP(SYS_BOOT5), (IEN | PTD | DIS | M4)) /*GPIO_7*/\
- MUX_VAL(CP(SYS_BOOT6), (IDIS | PTD | DIS | M4)) /*GPIO_8*/\
- /* - VIO_1V8*/\
- MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0)) /*SYS_OFF_MODE*/\
- MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M0)) /*SYS_CLKOUT1*/\
- MUX_VAL(CP(SYS_CLKOUT2), (IEN | PTU | EN | M0)) /*SYS_CLKOUT2*/\
- MUX_VAL(CP(JTAG_nTRST), (IEN | PTD | DIS | M0)) /*JTAG_nTRST*/\
- MUX_VAL(CP(JTAG_TCK), (IEN | PTD | DIS | M0)) /*JTAG_TCK*/\
- MUX_VAL(CP(JTAG_TMS), (IEN | PTD | DIS | M0)) /*JTAG_TMS*/\
- MUX_VAL(CP(JTAG_TDI), (IEN | PTD | DIS | M0)) /*JTAG_TDI*/\
- MUX_VAL(CP(JTAG_EMU0), (IEN | PTD | DIS | M0)) /*JTAG_EMU0*/\
- MUX_VAL(CP(JTAG_EMU1), (IEN | PTD | DIS | M0)) /*JTAG_EMU1*/\
- MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | EN | M0)) /*ETK_CLK*/\
- MUX_VAL(CP(ETK_CTL_ES2), (IDIS | PTD | DIS | M0)) /*ETK_CTL*/\
- MUX_VAL(CP(ETK_D0_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D0*/\
- MUX_VAL(CP(ETK_D1_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D1*/\
- MUX_VAL(CP(ETK_D2_ES2 ), (IEN | PTD | EN | M0)) /*ETK_D2*/\
- MUX_VAL(CP(ETK_D3_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D3*/\
- MUX_VAL(CP(ETK_D4_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D4*/\
- MUX_VAL(CP(ETK_D5_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D5*/\
- MUX_VAL(CP(ETK_D6_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D6*/\
- MUX_VAL(CP(ETK_D7_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D7*/\
- MUX_VAL(CP(ETK_D8_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D8*/\
- MUX_VAL(CP(ETK_D9_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D9*/\
- MUX_VAL(CP(ETK_D10_ES2), (IEN | PTD | DIS | M0)) /*ETK_D10*/\
- MUX_VAL(CP(ETK_D11_ES2), (IEN | PTD | DIS | M0)) /*ETK_D11*/\
- MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | DIS | M0)) /*ETK_D12*/\
- MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | DIS | M0)) /*ETK_D13*/\
- MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M0)) /*ETK_D14*/\
- MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | DIS | M0)) /*ETK_D15*/\
- /*Die to Die */\
- MUX_VAL(CP(D2D_MCAD1), (IEN | PTD | EN | M0)) /*d2d_mcad1*/\
- MUX_VAL(CP(D2D_MCAD2), (IEN | PTD | EN | M0)) /*d2d_mcad2*/\
- MUX_VAL(CP(D2D_MCAD3), (IEN | PTD | EN | M0)) /*d2d_mcad3*/\
- MUX_VAL(CP(D2D_MCAD4), (IEN | PTD | EN | M0)) /*d2d_mcad4*/\
- MUX_VAL(CP(D2D_MCAD5), (IEN | PTD | EN | M0)) /*d2d_mcad5*/\
- MUX_VAL(CP(D2D_MCAD6), (IEN | PTD | EN | M0)) /*d2d_mcad6*/\
- MUX_VAL(CP(D2D_MCAD7), (IEN | PTD | EN | M0)) /*d2d_mcad7*/\
- MUX_VAL(CP(D2D_MCAD8), (IEN | PTD | EN | M0)) /*d2d_mcad8*/\
- MUX_VAL(CP(D2D_MCAD9), (IEN | PTD | EN | M0)) /*d2d_mcad9*/\
- MUX_VAL(CP(D2D_MCAD10), (IEN | PTD | EN | M0)) /*d2d_mcad10*/\
- MUX_VAL(CP(D2D_MCAD11), (IEN | PTD | EN | M0)) /*d2d_mcad11*/\
- MUX_VAL(CP(D2D_MCAD12), (IEN | PTD | EN | M0)) /*d2d_mcad12*/\
- MUX_VAL(CP(D2D_MCAD13), (IEN | PTD | EN | M0)) /*d2d_mcad13*/\
- MUX_VAL(CP(D2D_MCAD14), (IEN | PTD | EN | M0)) /*d2d_mcad14*/\
- MUX_VAL(CP(D2D_MCAD15), (IEN | PTD | EN | M0)) /*d2d_mcad15*/\
- MUX_VAL(CP(D2D_MCAD16), (IEN | PTD | EN | M0)) /*d2d_mcad16*/\
- MUX_VAL(CP(D2D_MCAD17), (IEN | PTD | EN | M0)) /*d2d_mcad17*/\
- MUX_VAL(CP(D2D_MCAD18), (IEN | PTD | EN | M0)) /*d2d_mcad18*/\
- MUX_VAL(CP(D2D_MCAD19), (IEN | PTD | EN | M0)) /*d2d_mcad19*/\
- MUX_VAL(CP(D2D_MCAD20), (IEN | PTD | EN | M0)) /*d2d_mcad20*/\
- MUX_VAL(CP(D2D_MCAD21), (IEN | PTD | EN | M0)) /*d2d_mcad21*/\
- MUX_VAL(CP(D2D_MCAD22), (IEN | PTD | EN | M0)) /*d2d_mcad22*/\
- MUX_VAL(CP(D2D_MCAD23), (IEN | PTD | EN | M0)) /*d2d_mcad23*/\
- MUX_VAL(CP(D2D_MCAD24), (IEN | PTD | EN | M0)) /*d2d_mcad24*/\
- MUX_VAL(CP(D2D_MCAD25), (IEN | PTD | EN | M0)) /*d2d_mcad25*/\
- MUX_VAL(CP(D2D_MCAD26), (IEN | PTD | EN | M0)) /*d2d_mcad26*/\
- MUX_VAL(CP(D2D_MCAD27), (IEN | PTD | EN | M0)) /*d2d_mcad27*/\
- MUX_VAL(CP(D2D_MCAD28), (IEN | PTD | EN | M0)) /*d2d_mcad28*/\
- MUX_VAL(CP(D2D_MCAD29), (IEN | PTD | EN | M0)) /*d2d_mcad29*/\
- MUX_VAL(CP(D2D_MCAD30), (IEN | PTD | EN | M0)) /*d2d_mcad30*/\
- MUX_VAL(CP(D2D_MCAD31), (IEN | PTD | EN | M0)) /*d2d_mcad31*/\
- MUX_VAL(CP(D2D_MCAD32), (IEN | PTD | EN | M0)) /*d2d_mcad32*/\
- MUX_VAL(CP(D2D_MCAD33), (IEN | PTD | EN | M0)) /*d2d_mcad33*/\
- MUX_VAL(CP(D2D_MCAD34), (IEN | PTD | EN | M0)) /*d2d_mcad34*/\
- MUX_VAL(CP(D2D_MCAD35), (IEN | PTD | EN | M0)) /*d2d_mcad35*/\
- MUX_VAL(CP(D2D_MCAD36), (IEN | PTD | EN | M0)) /*d2d_mcad36*/\
- MUX_VAL(CP(D2D_CLK26MI), (IEN | PTD | DIS | M0)) /*d2d_clk26mi*/\
- MUX_VAL(CP(D2D_NRESPWRON), (IEN | PTD | EN | M0)) /*d2d_nrespwron*/\
- MUX_VAL(CP(D2D_NRESWARM), (IEN | PTU | EN | M0)) /*d2d_nreswarm */\
- MUX_VAL(CP(D2D_ARM9NIRQ), (IEN | PTD | DIS | M0)) /*d2d_arm9nirq */\
- MUX_VAL(CP(D2D_UMA2P6FIQ), (IEN | PTD | DIS | M0)) /*d2d_uma2p6fiq*/\
- MUX_VAL(CP(D2D_SPINT), (IEN | PTD | EN | M0)) /*d2d_spint*/\
- MUX_VAL(CP(D2D_FRINT), (IEN | PTD | EN | M0)) /*d2d_frint*/\
- MUX_VAL(CP(D2D_DMAREQ0), (IEN | PTD | DIS | M0)) /*d2d_dmareq0*/\
- MUX_VAL(CP(D2D_DMAREQ1), (IEN | PTD | DIS | M0)) /*d2d_dmareq1*/\
- MUX_VAL(CP(D2D_DMAREQ2), (IEN | PTD | DIS | M0)) /*d2d_dmareq2*/\
- MUX_VAL(CP(D2D_DMAREQ3), (IEN | PTD | DIS | M0)) /*d2d_dmareq3*/\
- MUX_VAL(CP(D2D_N3GTRST), (IEN | PTD | DIS | M0)) /*d2d_n3gtrst*/\
- MUX_VAL(CP(D2D_N3GTDI), (IEN | PTD | DIS | M0)) /*d2d_n3gtdi*/\
- MUX_VAL(CP(D2D_N3GTDO), (IEN | PTD | DIS | M0)) /*d2d_n3gtdo*/\
- MUX_VAL(CP(D2D_N3GTMS), (IEN | PTD | DIS | M0)) /*d2d_n3gtms*/\
- MUX_VAL(CP(D2D_N3GTCK), (IEN | PTD | DIS | M0)) /*d2d_n3gtck*/\
- MUX_VAL(CP(D2D_N3GRTCK), (IEN | PTD | DIS | M0)) /*d2d_n3grtck*/\
- MUX_VAL(CP(D2D_MSTDBY), (IEN | PTU | EN | M0)) /*d2d_mstdby*/\
- MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0)) /*d2d_swakeup*/\
- MUX_VAL(CP(D2D_IDLEREQ), (IEN | PTD | DIS | M0)) /*d2d_idlereq*/\
- MUX_VAL(CP(D2D_IDLEACK), (IEN | PTU | EN | M0)) /*d2d_idleack*/\
- MUX_VAL(CP(D2D_MWRITE), (IEN | PTD | DIS | M0)) /*d2d_mwrite*/\
- MUX_VAL(CP(D2D_SWRITE), (IEN | PTD | DIS | M0)) /*d2d_swrite*/\
- MUX_VAL(CP(D2D_MREAD), (IEN | PTD | DIS | M0)) /*d2d_mread*/\
- MUX_VAL(CP(D2D_SREAD), (IEN | PTD | DIS | M0)) /*d2d_sread*/\
- MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_mbusflag*/\
- MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_sbusflag*/\
- MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0)) /*sdrc_cke0*/\
- MUX_VAL(CP(SDRC_CKE1), (IDIS | PTD | DIS | M7)) /*sdrc_cke1*/\
-
-#endif
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = $(obj)lib$(BOARD).a
-
-COBJS := omap5912osk.o
-SOBJS := lowlevel_init.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-$(LIB): $(obj).depend $(OBJS) $(SOBJS)
- $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
-
-clean:
- rm -f $(SOBJS) $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
+++ /dev/null
-#
-# (C) Copyright 2002-2004
-# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
-# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
-#
-# (C) Copyright 2003
-# Texas Instruments, <www.ti.com>
-# Kshitij Gupta <Kshitij@ti.com>
-#
-# (C) Copyright 2004
-# Texas Instruments, <www.ti.com>
-# Rishi Bhattacharya <rishi@ti.com>
-#
-# TI OSK board with OMAP5912 (ARM925EJS) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# OSK has 1 bank of 256 MB SDRAM
-# Physical Address:
-# 1000'0000 to 2000'0000
-#
-#
-# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000
-# (mem base + reserved)
-#
-# we load ourself to 1108'0000
-#
-#
-
-
-TEXT_BASE = 0x11080000
+++ /dev/null
-/*
- * Board specific setup info
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
- *
- * Modified for OMAP 5912 OSK board by Rishi Bhattacharya, Apr 2004
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-
-#if defined(CONFIG_OMAP1610)
-#include <./configs/omap1510.h>
-#endif
-
-
-_TEXT_BASE:
- .word TEXT_BASE /* sdram load addr from config.mk */
-
-.globl lowlevel_init
-lowlevel_init:
-
- /*------------------------------------------------------*
- * Ensure i-cache is enabled *
- * To configure TC regs without fetching instruction *
- *------------------------------------------------------*/
- mrc p15, 0, r0, c1, c0
- orr r0, r0, #0x1000
- mcr p15, 0, r0, c1, c0
-
- /*------------------------------------------------------*
- *mask all IRQs by setting all bits in the INTMR default*
- *------------------------------------------------------*/
- mov r1, #0xffffffff
- ldr r0, =REG_IHL1_MIR
- str r1, [r0]
- ldr r0, =REG_IHL2_MIR
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT1) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT1
- ldr r1, VAL_ARM_IDLECT1
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT2) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT2
- ldr r1, VAL_ARM_IDLECT2
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT3) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT3
- ldr r1, VAL_ARM_IDLECT3
- str r1, [r0]
-
- mov r1, #0x01 /* PER_EN bit */
- ldr r0, REG_ARM_RSTCT2
- strh r1, [r0] /* CLKM; Peripheral reset. */
-
- /* Set CLKM to Sync-Scalable */
- mov r1, #0x1000
- ldr r0, REG_ARM_SYSST
-
- mov r2, #0
-1: cmp r2, #1
- streqh r1, [r0]
- add r2, r2, #1
- cmp r2, #0x100 /* wait for any bubbles to finish */
- bne 1b
-
- ldr r1, VAL_ARM_CKCTL
- ldr r0, REG_ARM_CKCTL
- strh r1, [r0]
-
- /* a few nops to let settle */
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
-
- /* setup DPLL 1 */
- /* Ramp up the clock to 96Mhz */
- ldr r1, VAL_DPLL1_CTL
- ldr r0, REG_DPLL1_CTL
- strh r1, [r0]
- ands r1, r1, #0x10 /* Check if PLL is enabled. */
- beq lock_end /* Do not look for lock if BYPASS selected */
-2:
- ldrh r1, [r0]
- ands r1, r1, #0x01 /* Check the LOCK bit.*/
- beq 2b /* loop until bit goes hi. */
-lock_end:
-
- /*------------------------------------------------------*
- * Turn off the watchdog during init... *
- *------------------------------------------------------*/
- ldr r0, REG_WATCHDOG
- ldr r1, WATCHDOG_VAL1
- str r1, [r0]
- ldr r1, WATCHDOG_VAL2
- str r1, [r0]
- ldr r0, REG_WSPRDOG
- ldr r1, WSPRDOG_VAL1
- str r1, [r0]
- ldr r0, REG_WWPSDOG
-
-watch1Wait:
- ldr r1, [r0]
- tst r1, #0x10
- bne watch1Wait
-
- ldr r0, REG_WSPRDOG
- ldr r1, WSPRDOG_VAL2
- str r1, [r0]
- ldr r0, REG_WWPSDOG
-watch2Wait:
- ldr r1, [r0]
- tst r1, #0x10
- bne watch2Wait
-
- /* Set memory timings corresponding to the new clock speed */
- ldr r3, VAL_SDRAM_CONFIG_SDF0
-
- /* Check execution location to determine current execution location
- * and branch to appropriate initialization code.
- */
- mov r0, #0x10000000 /* Load physical SDRAM base. */
- mov r1, pc /* Get current execution location. */
- cmp r1, r0 /* Compare. */
- bge skip_sdram /* Skip over EMIF-fast initialization if running from SDRAM. */
-
- /* identify the device revision, -- TMX or TMP(TMS) */
- ldr r0, REG_DEVICE_ID
- ldr r1, [r0]
-
- ldr r0, VAL_DEVICE_ID_TMP
- mov r1, r1, lsl #15
- mov r1, r1, lsr #16
- cmp r0, r1
- bne skip_TMP_Patch
-
- /* Enable TMP/TMS device new features */
- mov r0, #1
- ldr r1, REG_TC_EMIFF_DOUBLER
- str r0, [r1]
-
- /* Enable new ac parameters */
- mov r0, #0x0b
- ldr r1, REG_SDRAM_CONFIG2
- str r0, [r1]
-
- ldr r3, VAL_SDRAM_CONFIG_SDF1
-
-skip_TMP_Patch:
-
- /*
- * Delay for SDRAM initialization.
- */
- mov r0, #0x1800 /* value should be checked */
-3:
- subs r0, r0, #0x1 /* Decrement count */
- bne 3b
-
- /*
- * Set SDRAM control values. Disable refresh before MRS command.
- */
-
- /* mobile ddr operation */
- ldr r0, REG_SDRAM_OPERATION
- mov r2, #07
- str r2, [r0]
-
- /* config register */
- ldr r0, REG_SDRAM_CONFIG
- str r3, [r0]
-
- /* manual command register */
- ldr r0, REG_SDRAM_MANUAL_CMD
-
- /* issue set cke high */
- mov r1, #CMD_SDRAM_CKE_SET_HIGH
- str r1, [r0]
-
- /* issue nop */
- mov r1, #CMD_SDRAM_NOP
- str r1, [r0]
-
- mov r2, #0x0100
-waitMDDR1:
- subs r2, r2, #1
- bne waitMDDR1 /* delay loop */
-
- /* issue precharge */
- mov r1, #CMD_SDRAM_PRECHARGE
- str r1, [r0]
-
- /* issue autorefresh x 2 */
- mov r1, #CMD_SDRAM_AUTOREFRESH
- str r1, [r0]
- str r1, [r0]
-
- /* mrs register ddr mobile */
- ldr r0, REG_SDRAM_MRS
- mov r1, #0x33
- str r1, [r0]
-
- /* emrs1 low-power register */
- ldr r0, REG_SDRAM_EMRS1
- /* self refresh on all banks */
- mov r1, #0
- str r1, [r0]
-
- ldr r0, REG_DLL_URD_CONTROL
- ldr r1, DLL_URD_CONTROL_VAL
- str r1, [r0]
-
- ldr r0, REG_DLL_LRD_CONTROL
- ldr r1, DLL_LRD_CONTROL_VAL
- str r1, [r0]
-
- ldr r0, REG_DLL_WRT_CONTROL
- ldr r1, DLL_WRT_CONTROL_VAL
- str r1, [r0]
-
- /* delay loop */
- mov r0, #0x0100
-waitMDDR2:
- subs r0, r0, #1
- bne waitMDDR2
-
- /*
- * Delay for SDRAM initialization.
- */
- mov r0, #0x1800
-4:
- subs r0, r0, #1 /* Decrement count. */
- bne 4b
- b common_tc
-
-skip_sdram:
- ldr r0, REG_SDRAM_CONFIG
- str r3, [r0]
-
-common_tc:
- /* slow interface */
- ldr r1, VAL_TC_EMIFS_CS0_CONFIG
- ldr r0, REG_TC_EMIFS_CS0_CONFIG
- str r1, [r0] /* Chip Select 0 */
-
- ldr r1, VAL_TC_EMIFS_CS1_CONFIG
- ldr r0, REG_TC_EMIFS_CS1_CONFIG
- str r1, [r0] /* Chip Select 1 */
-
- ldr r1, VAL_TC_EMIFS_CS3_CONFIG
- ldr r0, REG_TC_EMIFS_CS3_CONFIG
- str r1, [r0] /* Chip Select 3 */
-
- ldr r1, VAL_TC_EMIFS_DWS
- ldr r0, REG_TC_EMIFS_DWS
- str r1, [r0] /* Enable EMIFS.RDY for CS1 (ether) */
-
-#ifdef CONFIG_H2_OMAP1610
- /* inserting additional 2 clock cycle hold time for LAN */
- ldr r0, REG_TC_EMIFS_CS1_ADVANCED
- ldr r1, VAL_TC_EMIFS_CS1_ADVANCED
- str r1, [r0]
-#endif
- /* Start MPU Timer 1 */
- ldr r0, REG_MPU_LOAD_TIMER
- ldr r1, VAL_MPU_LOAD_TIMER
- str r1, [r0]
-
- ldr r0, REG_MPU_CNTL_TIMER
- ldr r1, VAL_MPU_CNTL_TIMER
- str r1, [r0]
-
- /* back to arch calling code */
- mov pc, lr
-
- /* the literal pools origin */
- .ltorg
-
-REG_DEVICE_ID: /* 32 bits */
- .word 0xfffe2004
-REG_TC_EMIFS_CONFIG:
- .word 0xfffecc0c
-REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */
- .word 0xfffecc10
-REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */
- .word 0xfffecc14
-REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */
- .word 0xfffecc18
-REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */
- .word 0xfffecc1c
-REG_TC_EMIFS_DWS: /* 32 bits */
- .word 0xfffecc40
-#ifdef CONFIG_H2_OMAP1610
-REG_TC_EMIFS_CS1_ADVANCED: /* 32 bits */
- .word 0xfffecc54
-#endif
-
-/* MPU clock/reset/power mode control registers */
-REG_ARM_CKCTL: /* 16 bits */
- .word 0xfffece00
-REG_ARM_IDLECT3: /* 16 bits */
- .word 0xfffece24
-REG_ARM_IDLECT2: /* 16 bits */
- .word 0xfffece08
-REG_ARM_IDLECT1: /* 16 bits */
- .word 0xfffece04
-REG_ARM_RSTCT2: /* 16 bits */
- .word 0xfffece14
-REG_ARM_SYSST: /* 16 bits */
- .word 0xfffece18
-
-/* DPLL control registers */
-REG_DPLL1_CTL: /* 16 bits */
- .word 0xfffecf00
-
-/* Watch Dog register */
-/* secure watchdog stop */
-REG_WSPRDOG:
- .word 0xfffeb048
-/* watchdog write pending */
-REG_WWPSDOG:
- .word 0xfffeb034
-
-WSPRDOG_VAL1:
- .word 0x0000aaaa
-WSPRDOG_VAL2:
- .word 0x00005555
-
-/* SDRAM config is: auto refresh enabled, 16 bit 4 bank,
- counter @8192 rows, 10 ns, 8 burst */
-REG_SDRAM_CONFIG:
- .word 0xfffecc20
-REG_SDRAM_CONFIG2:
- .word 0xfffecc3c
-REG_TC_EMIFF_DOUBLER: /* 32 bits */
- .word 0xfffecc60
-
-/* Operation register */
-REG_SDRAM_OPERATION:
- .word 0xfffecc80
-
-/* Manual command register */
-REG_SDRAM_MANUAL_CMD:
- .word 0xfffecc84
-
-/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */
-REG_SDRAM_MRS:
- .word 0xfffecc70
-
-/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */
-REG_SDRAM_EMRS1:
- .word 0xfffecc78
-
-/* WRT DLL register */
-REG_DLL_WRT_CONTROL:
- .word 0xfffecc68
-DLL_WRT_CONTROL_VAL:
- .word 0x03f00002 /* Phase of 72deg, write offset +31 */
-
-/* URD DLL register */
-REG_DLL_URD_CONTROL:
- .word 0xfffeccc0
-DLL_URD_CONTROL_VAL:
- .word 0x00800002 /* Phase of 72deg, read offset +31 */
-
-/* LRD DLL register */
-REG_DLL_LRD_CONTROL:
- .word 0xfffecccc
-DLL_LRD_CONTROL_VAL:
- .word 0x00800002 /* read offset +31 */
-
-REG_WATCHDOG:
- .word 0xfffec808
-WATCHDOG_VAL1:
- .word 0x000000f5
-WATCHDOG_VAL2:
- .word 0x000000a0
-
-REG_MPU_LOAD_TIMER:
- .word 0xfffec504
-REG_MPU_CNTL_TIMER:
- .word 0xfffec500
-VAL_MPU_LOAD_TIMER:
- .word 0xffffffff
-VAL_MPU_CNTL_TIMER:
- .word 0xffffffa1
-
-/* 96 MHz Samsung Mobile DDR */
-/* Original setting for TMX device */
-VAL_SDRAM_CONFIG_SDF0:
- .word 0x0014e6fe
-
-/* NEW_SYS_FREQ mode (valid only TMP/TMS devices) */
-VAL_SDRAM_CONFIG_SDF1:
- .word 0x0114e6fe
-
-VAL_ARM_CKCTL:
- .word 0x2000 /* was: 0x3000, now use CLK_REF for timer input */
-VAL_DPLL1_CTL:
- .word 0x2830
-
-#ifdef CONFIG_OSK_OMAP5912
-VAL_TC_EMIFS_CS0_CONFIG:
- .word 0x002130b0
-VAL_TC_EMIFS_CS1_CONFIG:
- .word 0x00001133
-VAL_TC_EMIFS_CS2_CONFIG:
- .word 0x000055f0
-VAL_TC_EMIFS_CS3_CONFIG:
- .word 0x88013141
-VAL_TC_EMIFS_DWS: /* Enable EMIFS.RDY for CS1 access (ether) */
- .word 0x000000c0
-VAL_DEVICE_ID_TMP: /* TMP/TMS=0xb65f, TMX=0xb58c */
- .word 0xb65f
-#endif
-
-#ifdef CONFIG_H2_OMAP1610
-VAL_TC_EMIFS_CS0_CONFIG:
- .word 0x00203331
-VAL_TC_EMIFS_CS1_CONFIG:
- .word 0x8180fff3
-VAL_TC_EMIFS_CS2_CONFIG:
- .word 0xf800f22a
-VAL_TC_EMIFS_CS3_CONFIG:
- .word 0x88013141
-VAL_TC_EMIFS_CS1_ADVANCED:
- .word 0x00000022
-#endif
-
-VAL_ARM_IDLECT1:
- .word 0x00000400
-VAL_ARM_IDLECT2:
- .word 0x00000886
-VAL_ARM_IDLECT3:
- .word 0x00000015
-
-/* command values */
-.equ CMD_SDRAM_NOP, 0x00000000
-.equ CMD_SDRAM_PRECHARGE, 0x00000001
-.equ CMD_SDRAM_AUTOREFRESH, 0x00000002
-.equ CMD_SDRAM_CKE_SET_HIGH, 0x00000007
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2002
- * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Rishi Bhattacharya <rishi@ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#if defined(CONFIG_OMAP1610)
-#include <./configs/omap1510.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-void flash__init (void);
-void ether__init (void);
-void set_muxconf_regs (void);
-void peripheral_power_enable (void);
-
-#define COMP_MODE_ENABLE ((unsigned int)0x0000EAEF)
-
-static inline void delay (unsigned long loops)
-{
- __asm__ volatile ("1:\n"
- "subs %0, %1, #1\n"
- "bne 1b":"=r" (loops):"0" (loops));
-}
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-
-int board_init (void)
-{
- gd->bd->bi_arch_number = MACH_TYPE_OMAP_OSK;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = 0x10000100;
-
- /* Configure MUX settings */
- set_muxconf_regs ();
- peripheral_power_enable ();
-
-/* this speeds up your boot a quite a bit. However to make it
- * work, you need make sure your kernel startup flush bug is fixed.
- * ... rkw ...
- */
- icache_enable ();
-
- flash__init ();
- ether__init ();
- return 0;
-}
-
-
-int misc_init_r (void)
-{
- /* currently empty */
- return (0);
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-void flash__init (void)
-{
-#define EMIFS_GlB_Config_REG 0xfffecc0c
- unsigned int regval;
- regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG);
- /* Turn off write protection for flash devices. */
- regval = regval | 0x0001;
- *((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval;
-}
-/*************************************************************
- Routine:ether__init
- Description: take the Ethernet controller out of reset and wait
- for the EEPROM load to complete.
-*************************************************************/
-void ether__init (void)
-{
-#define ETH_CONTROL_REG 0x0480000b
- int i;
-
- *((volatile unsigned short *) 0xfffece08) = 0x03FF;
- *((volatile unsigned short *) 0xfffb3824) = 0x8000;
- *((volatile unsigned short *) 0xfffb3830) = 0x0000;
- *((volatile unsigned short *) 0xfffb3834) = 0x0009;
- *((volatile unsigned short *) 0xfffb3838) = 0x0009;
- *((volatile unsigned short *) 0xfffb3818) = 0x0002;
- *((volatile unsigned short *) 0xfffb382C) = 0x0048;
- *((volatile unsigned short *) 0xfffb3824) = 0x8603;
- udelay (3);
- for (i=0;i<2000;i++);
- *((volatile unsigned short *) 0xfffb381C) = 0x6610;
- udelay (30);
- for (i=0;i<10000;i++);
-
- *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
- udelay (3);
-
-
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-int dram_init (void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
- return 0;
-}
-
-/******************************************************
- Routine: set_muxconf_regs
- Description: Setting up the configuration Mux registers
- specific to the hardware
-*******************************************************/
-void set_muxconf_regs (void)
-{
- volatile unsigned int *MuxConfReg;
- /* set each registers to its reset value; */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
- /* setup for UART1 */
- *MuxConfReg &= ~(0x02000000); /* bit 25 */
- /* setup for UART2 */
- *MuxConfReg &= ~(0x01000000); /* bit 24 */
- /* Disable Uwire CS Hi-Z */
- *MuxConfReg |= 0x08000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_3);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_4);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_5);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_6);
- /*setup mux for UART3 */
- *MuxConfReg |= 0x00000001; /* bit3, 1, 0 (mux0 5,5,26) */
- *MuxConfReg &= ~0x0000003e;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_7);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_8);
- /* Disable Uwire CS Hi-Z */
- *MuxConfReg |= 0x00001200; /*bit 9 for CS0 12 for CS3 */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_9);
- /* Need to turn on bits 21 and 12 in FUNC_MUX_CTRL_9 so the */
- /* hardware will actually use TX and RTS based on bit 25 in */
- /* FUNC_MUX_CTRL_0. I told you this thing was screwy! */
- *MuxConfReg |= 0x00201000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_A);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_B);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_C);
- /* setup for UART2 */
- /* Need to turn on bits 27 and 24 in FUNC_MUX_CTRL_C so the */
- /* hardware will actually use TX and RTS based on bit 24 in */
- /* FUNC_MUX_CTRL_0. */
- *MuxConfReg |= 0x09000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_D);
- *MuxConfReg |= 0x00000020;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_0);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_1);
- *MuxConfReg = 0x00000000;
- /* mux setup for SD/MMC driver */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_2);
- *MuxConfReg &= 0xFFFE0FFF;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_3);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
- /* bit 13 for MMC2 XOR_CLK */
- *MuxConfReg &= ~(0x00002000);
- /* bit 29 for UART 1 */
- *MuxConfReg &= ~(0x00002000);
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
- /* Configure for USB. Turn on VBUS_CTRL and VBUS_MODE. */
- *MuxConfReg |= 0x000C0000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int)USB_TRANSCEIVER_CTRL);
- *MuxConfReg &= ~(0x00000070);
- *MuxConfReg &= ~(0x00000008);
- *MuxConfReg |= 0x00000003;
- *MuxConfReg |= 0x00000180;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
- /* bit 17, software controls VBUS */
- *MuxConfReg &= ~(0x00020000);
- /* Enable USB 48 and 12M clocks */
- *MuxConfReg |= 0x00000200;
- *MuxConfReg &= ~(0x00000180);
- /*2.75V for MMCSDIO1 */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) VOLTAGE_CTRL_0);
- *MuxConfReg = 0x00001FE7;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_0);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_1);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_3);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_4);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_4);
- *MuxConfReg = 0x00000000;
- /* Turn on UART2 48 MHZ clock */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
- *MuxConfReg |= 0x40000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) USB_OTG_CTRL);
- /* setup for USB VBus detection OMAP161x */
- *MuxConfReg |= 0x00040000; /* bit 18 */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
- /* PullUps for SD/MMC driver */
- *MuxConfReg |= ~(0xFFFE0FFF);
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int)COMP_MODE_CTRL_0);
- *MuxConfReg = COMP_MODE_ENABLE;
-}
-
-/******************************************************
- Routine: peripheral_power_enable
- Description: Enable the power for UART1
-*******************************************************/
-void peripheral_power_enable (void)
-{
-#define UART1_48MHZ_ENABLE ((unsigned short)0x0200)
-#define SW_CLOCK_REQUEST ((volatile unsigned short *)0xFFFE0834)
-
- *SW_CLOCK_REQUEST |= UART1_48MHZ_ENABLE;
-}
-
-/*
- * Check Board Identity
- */
-int checkboard(void)
-{
- char *s = getenv("serial#");
-
- puts("Board: OSK5912");
-
- if (s != NULL) {
- puts(", serial# ");
- puts(s);
- }
- putc('\n');
-
- return (0);
-}
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = $(obj)lib$(BOARD).a
-
-COBJS := omap730p2.o flash.o
-SOBJS := lowlevel_init.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-$(LIB): $(obj).depend $(OBJS) $(SOBJS)
- $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
-
-clean:
- rm -f $(SOBJS) $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
+++ /dev/null
-#
-# (C) Copyright 2002
-# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
-# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
-#
-# (C) Copyright 2003
-# Texas Instruments, <www.ti.com>
-# Kshitij Gupta <Kshitij@ti.com>
-#
-# TI Perseus 2 board with OMAP720 (ARM925EJS) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# Innovator has 1 bank of 256 MB SDRAM
-# Physical Address:
-# 1000'0000 to 2000'0000
-#
-#
-# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000
-# (mem base + reserved)
-#
-# we load ourself to 1108'0000
-#
-#
-
-TEXT_BASE = 0x11080000
+++ /dev/null
-/*
- * (C) Copyright 2001
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <linux/byteorder/swab.h>
-
-#define PHYS_FLASH_SECT_SIZE 0x00020000 /* 256 KB sectors (x2) */
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-/* Board support for 1 or 2 flash devices */
-#undef FLASH_PORT_WIDTH32
-#define FLASH_PORT_WIDTH16
-
-#ifdef FLASH_PORT_WIDTH16
-#define FLASH_PORT_WIDTH ushort
-#define FLASH_PORT_WIDTHV vu_short
-#define SWAP(x) __swab16(x)
-#else
-#define FLASH_PORT_WIDTH ulong
-#define FLASH_PORT_WIDTHV vu_long
-#define SWAP(x) __swab32(x)
-#endif
-
-#define FPW FLASH_PORT_WIDTH
-#define FPWV FLASH_PORT_WIDTHV
-
-#define mb() __asm__ __volatile__ ("" : : : "memory")
-
-
-/* Flash Organization Structure */
-typedef struct OrgDef {
- unsigned int sector_number;
- unsigned int sector_size;
-} OrgDef;
-
-
-/* Flash Organizations */
-OrgDef OrgIntel_28F256L18T[] = {
- {4, 32 * 1024}, /* 4 * 32kBytes sectors */
- {255, 128 * 1024}, /* 255 * 128kBytes sectors */
-};
-
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-unsigned long flash_init (void);
-static ulong flash_get_size (FPW * addr, flash_info_t * info);
-static int write_data (flash_info_t * info, ulong dest, FPW data);
-static void flash_get_offsets (ulong base, flash_info_t * info);
-void inline spin_wheel (void);
-void flash_print_info (flash_info_t * info);
-void flash_unprotect_sectors (FPWV * addr);
-int flash_erase (flash_info_t * info, int s_first, int s_last);
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- int i;
- ulong size = 0;
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
- switch (i) {
- case 0:
- flash_get_size ((FPW *) PHYS_FLASH_1, &flash_info[i]);
- flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
- break;
- default:
- panic ("configured too many flash banks!\n");
- break;
- }
- size += flash_info[i].size;
- }
-
- /* Protect monitor and environment sectors
- */
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_SYS_FLASH_BASE,
- CONFIG_SYS_FLASH_BASE + monitor_flash_len - 1, &flash_info[0]);
-
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]);
-
- return size;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t * info)
-{
- int i;
- OrgDef *pOrgDef;
-
- pOrgDef = OrgIntel_28F256L18T;
- if (info->flash_id == FLASH_UNKNOWN) {
- return;
- }
-
- if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
- for (i = 0; i < info->sector_count; i++) {
- if (i > 255) {
- info->start[i] = base + (i * 0x8000);
- info->protect[i] = 0;
- } else {
- info->start[i] = base +
- (i * PHYS_FLASH_SECT_SIZE);
- info->protect[i] = 0;
- }
- }
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_INTEL:
- printf ("INTEL ");
- break;
- default:
- printf ("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_28F256L18T:
- printf ("FLASH 28F256L18T\n");
- break;
- default:
- printf ("Unknown Chip Type\n");
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i], info->protect[i] ? " (RO)" : " ");
- }
- printf ("\n");
- return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (FPW * addr, flash_info_t * info)
-{
- volatile FPW value;
-
- /* Write auto select command: read Manufacturer ID */
- addr[0x5555] = (FPW) 0x00AA00AA;
- addr[0x2AAA] = (FPW) 0x00550055;
- addr[0x5555] = (FPW) 0x00900090;
-
- mb ();
- value = addr[0];
-
- switch (value) {
-
- case (FPW) INTEL_MANUFACT:
- info->flash_id = FLASH_MAN_INTEL;
- break;
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- addr[0] = (FPW) 0x00FF00FF; /* restore read mode */
- return (0); /* no or unknown flash */
- }
-
- mb ();
- value = addr[1]; /* device ID */
- switch (value) {
-
- case (FPW) (INTEL_ID_28F256L18T):
- info->flash_id += FLASH_28F256L18T;
- info->sector_count = 259;
- info->size = 0x02000000;
- break; /* => 32 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- break;
- }
-
- if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
- printf ("** ERROR: sector count %d > max (%d) **\n",
- info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
- info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
- }
-
- addr[0] = (FPW) 0x00FF00FF; /* restore read mode */
-
- return (info->size);
-}
-
-
-/* unprotects a sector for write and erase
- * on some intel parts, this unprotects the entire chip, but it
- * wont hurt to call this additional times per sector...
- */
-void flash_unprotect_sectors (FPWV * addr)
-{
-#define PD_FINTEL_WSMS_READY_MASK 0x0080
-
- *addr = (FPW) 0x00500050; /* clear status register */
-
- /* this sends the clear lock bit command */
- *addr = (FPW) 0x00600060;
- *addr = (FPW) 0x00D000D0;
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
- int flag, prot, sect;
- ulong type, start, last;
- int rcode = 0;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- type = (info->flash_id & FLASH_VENDMASK);
- if ((type != FLASH_MAN_INTEL)) {
- printf ("Can't erase unknown flash type %08lx - aborted\n",
- info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
-
- start = get_timer (0);
- last = start;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- FPWV *addr = (FPWV *) (info->start[sect]);
- FPW status;
-
- printf ("Erasing sector %2d ... ", sect);
-
- flash_unprotect_sectors (addr);
-
- /* arm simple, non interrupt dependent timer */
- reset_timer_masked ();
-
- *addr = (FPW) 0x00500050;/* clear status register */
- *addr = (FPW) 0x00200020;/* erase setup */
- *addr = (FPW) 0x00D000D0;/* erase confirm */
-
- while (((status =
- *addr) & (FPW) 0x00800080) !=
- (FPW) 0x00800080) {
- if (get_timer_masked () >
- CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- /* suspend erase */
- *addr = (FPW) 0x00B000B0;
- /* reset to read mode */
- *addr = (FPW) 0x00FF00FF;
- rcode = 1;
- break;
- }
- }
-
- /* clear status register cmd. */
- *addr = (FPW) 0x00500050;
- *addr = (FPW) 0x00FF00FF;/* resest to read mode */
- printf (" done\n");
- }
- }
- return rcode;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- ulong cp, wp;
- FPW data;
- int count, i, l, rc, port_width;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return 4;
- }
-/* get lower word aligned address */
-#ifdef FLASH_PORT_WIDTH16
- wp = (addr & ~1);
- port_width = 2;
-#else
- wp = (addr & ~3);
- port_width = 4;
-#endif
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i = 0, cp = wp; i < l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
- for (; i < port_width && cnt > 0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt == 0 && i < port_width; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- if ((rc = write_data (info, wp, SWAP (data))) != 0) {
- return (rc);
- }
- wp += port_width;
- }
-
- /*
- * handle word aligned part
- */
- count = 0;
- while (cnt >= port_width) {
- data = 0;
- for (i = 0; i < port_width; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_data (info, wp, SWAP (data))) != 0) {
- return (rc);
- }
- wp += port_width;
- cnt -= port_width;
- if (count++ > 0x800) {
- spin_wheel ();
- count = 0;
- }
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i < port_width; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- return (write_data (info, wp, SWAP (data)));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word or halfword to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t * info, ulong dest, FPW data)
-{
- FPWV *addr = (FPWV *) dest;
- ulong status;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*addr & data) != data) {
- printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr);
- return (2);
- }
- flash_unprotect_sectors (addr);
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
- *addr = (FPW) 0x00400040; /* write setup */
- *addr = data;
-
- /* arm simple, non interrupt dependent timer */
- reset_timer_masked ();
-
- /* wait while polling the status register */
- while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
- if (get_timer_masked () > CONFIG_SYS_FLASH_WRITE_TOUT) {
- *addr = (FPW) 0x00FF00FF; /* restore read mode */
- return (1);
- }
- }
- *addr = (FPW) 0x00FF00FF; /* restore read mode */
- return (0);
-}
-
-void inline spin_wheel (void)
-{
- static int p = 0;
- static char w[] = "\\/-";
-
- printf ("\010%c", w[p]);
- (++p == 3) ? (p = 0) : 0;
-}
+++ /dev/null
-/*
- * Board specific setup info
- *
- * (C) Copyright 2003-2004
- *
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
- *
- * Modified for OMAP730 P2 Board by Dave Peverley, MPC-Data Limited
- * (http://www.mpc-data.co.uk)
- *
- * TODO : Tidy up and change to use system register defines
- * from omap730.h where possible.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-
-#if defined(CONFIG_OMAP730)
-#include <./configs/omap730.h>
-#endif
-
-_TEXT_BASE:
- .word TEXT_BASE /* sdram load addr from config.mk */
-
-.globl lowlevel_init
-lowlevel_init:
- /* Save callers address in r11 - r11 must never be modified */
- mov r11, lr
-
- /*------------------------------------------------------*
- *mask all IRQs by setting all bits in the INTMR default*
- *------------------------------------------------------*/
- mov r1, #0xffffffff
- ldr r0, =REG_IHL1_MIR
- str r1, [r0]
- ldr r0, =REG_IHL2_MIR
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT1) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT1
- ldr r1, VAL_ARM_IDLECT1
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT2) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT2
- ldr r1, VAL_ARM_IDLECT2
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT3) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT3
- ldr r1, VAL_ARM_IDLECT3
- str r1, [r0]
-
-
- mov r1, #0x01 /* PER_EN bit */
- ldr r0, REG_ARM_RSTCT2
- strh r1, [r0] /* CLKM; Peripheral reset. */
-
- /* Set CLKM to Sync-Scalable */
- /* I supposedly need to enable the dsp clock before switching */
- mov r1, #0x1000
- ldr r0, REG_ARM_SYSST
- strh r1, [r0]
- mov r0, #0x400
-1:
- subs r0, r0, #0x1 /* wait for any bubbles to finish */
- bne 1b
- ldr r1, VAL_ARM_CKCTL
- ldr r0, REG_ARM_CKCTL
- strh r1, [r0]
-
- /* a few nops to let settle */
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
-
- /* setup DPLL 1 */
- /* Ramp up the clock to 96Mhz */
- ldr r1, VAL_DPLL1_CTL
- ldr r0, REG_DPLL1_CTL
- strh r1, [r0]
- ands r1, r1, #0x10 /* Check if PLL is enabled. */
- beq lock_end /* Do not look for lock if BYPASS selected */
-2:
- ldrh r1, [r0]
- ands r1, r1, #0x01 /* Check the LOCK bit.*/
- beq 2b /* loop until bit goes hi. */
-lock_end:
-
- /*------------------------------------------------------*
- * Turn off the watchdog during init... *
- *------------------------------------------------------*/
- ldr r0, REG_WATCHDOG
- ldr r1, WATCHDOG_VAL1
- str r1, [r0]
- ldr r1, WATCHDOG_VAL2
- str r1, [r0]
- ldr r0, REG_WSPRDOG
- ldr r1, WSPRDOG_VAL1
- str r1, [r0]
- ldr r0, REG_WWPSDOG
-
-watch1Wait:
- ldr r1, [r0]
- tst r1, #0x10
- bne watch1Wait
-
- ldr r0, REG_WSPRDOG
- ldr r1, WSPRDOG_VAL2
- str r1, [r0]
- ldr r0, REG_WWPSDOG
-watch2Wait:
- ldr r1, [r0]
- tst r1, #0x10
- bne watch2Wait
-
- /* Set memory timings corresponding to the new clock speed */
-
- /* Check execution location to determine current execution location
- * and branch to appropriate initialization code.
- */
- /* Compare physical SDRAM base & current execution location. */
- and r0, pc, #0xF0000000
- /* Compare. */
- cmp r0, #0
- /* Skip over EMIF-fast initialization if running from SDRAM. */
- bne skip_sdram
-
- /*
- * Delay for SDRAM initialization.
- */
- mov r3, #0x1800 /* value should be checked */
-3:
- subs r3, r3, #0x1 /* Decrement count */
- bne 3b
-
- ldr r0, REG_SDRAM_CONFIG
- ldr r1, SDRAM_CONFIG_VAL
- str r1, [r0]
-
- ldr r0, REG_SDRAM_MRS_LEGACY
- ldr r1, SDRAM_MRS_VAL
- str r1, [r0]
-
-skip_sdram:
-
-common_tc:
- /* slow interface */
- ldr r1, VAL_TC_EMIFS_CS0_CONFIG
- ldr r0, REG_TC_EMIFS_CS0_CONFIG
- str r1, [r0] /* Chip Select 0 */
-
- ldr r1, VAL_TC_EMIFS_CS1_CONFIG
- ldr r0, REG_TC_EMIFS_CS1_CONFIG
- str r1, [r0] /* Chip Select 1 */
- ldr r1, VAL_TC_EMIFS_CS2_CONFIG
- ldr r0, REG_TC_EMIFS_CS2_CONFIG
- str r1, [r0] /* Chip Select 2 */
- ldr r1, VAL_TC_EMIFS_CS3_CONFIG
- ldr r0, REG_TC_EMIFS_CS3_CONFIG
- str r1, [r0] /* Chip Select 3 */
-
- /* 48MHz clock request for UART1 */
- ldr r1, PERSEUS2_CONFIG_BASE
- ldrh r0, [r1, #CONFIG_PCC_CONF]
- orr r0, r0, #CONF_MOD_UART1_CLK_MODE_R
- strh r0, [r1, #CONFIG_PCC_CONF]
-
- /* Initialize public and private rheas
- * - set access factor 2 on both rhea / strobe
- * - disable write buffer on strb0, enable write buffer on strb1
- */
-
- ldr R0, REG_RHEA_PUB_CTL
- ldr R1, REG_RHEA_PRIV_CTL
- ldr R2, VAL_RHEA_CTL
- strh R2, [R0]
- strh R2, [R1]
- mov R3, #2 /* disable write buffer on strb0, enable write buffer on strb1 */
- strh R3, [R0, #0x08] /* arm rhea control reg */
- strh R3, [R1, #0x08]
-
- /* enable IRQ and FIQ */
-
- mrs r4, CPSR
- bic r4, r4, #IRQ_MASK
- bic r4, r4, #FIQ_MASK
- msr CPSR, r4
-
- /* set TAP CONF to TRI EMULATION */
-
- ldr r1, [r0, #CONFIG_MODE2]
- bic r1, r1, #0x18
- orr r1, r1, #0x10
- str r1, [r0, #CONFIG_MODE2]
-
- /* set tdbgen to 1 */
-
- ldr r0, PERSEUS2_CONFIG_BASE
- ldr r1, [r0, #CONFIG_MODE1]
- mov r2, #0x10000
- orr r1, r1, r2
- str r1, [r0, #CONFIG_MODE1]
-
-#ifdef CONFIG_P2_OMAP1610
- /* inserting additional 2 clock cycle hold time for LAN */
- ldr r0, REG_TC_EMIFS_CS1_ADVANCED
- ldr r1, VAL_TC_EMIFS_CS1_ADVANCED
- str r1, [r0]
-#endif
- /* Start MPU Timer 1 */
- ldr r0, REG_MPU_LOAD_TIMER
- ldr r1, VAL_MPU_LOAD_TIMER
- str r1, [r0]
-
- ldr r0, REG_MPU_CNTL_TIMER
- ldr r1, VAL_MPU_CNTL_TIMER
- str r1, [r0]
-
- /* back to arch calling code */
- mov pc, r11
-
- /* the literal pools origin */
- .ltorg
-
-REG_TC_EMIFS_CONFIG: /* 32 bits */
- .word 0xfffecc0c
-REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */
- .word 0xfffecc10
-REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */
- .word 0xfffecc14
-REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */
- .word 0xfffecc18
-REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */
- .word 0xfffecc1c
-
-#ifdef CONFIG_P2_OMAP730
-REG_TC_EMIFS_CS1_ADVANCED: /* 32 bits */
- .word 0xfffecc54
-#endif
-
-/* MPU clock/reset/power mode control registers */
-REG_ARM_CKCTL: /* 16 bits */
- .word 0xfffece00
-
-REG_ARM_IDLECT3: /* 16 bits */
- .word 0xfffece24
-REG_ARM_IDLECT2: /* 16 bits */
- .word 0xfffece08
-REG_ARM_IDLECT1: /* 16 bits */
- .word 0xfffece04
-
-REG_ARM_RSTCT2: /* 16 bits */
- .word 0xfffece14
-REG_ARM_SYSST: /* 16 bits */
- .word 0xfffece18
-/* DPLL control registers */
-REG_DPLL1_CTL: /* 16 bits */
- .word 0xfffecf00
-
-/* Watch Dog register */
-/* secure watchdog stop */
-REG_WSPRDOG:
- .word 0xfffeb048
-/* watchdog write pending */
-REG_WWPSDOG:
- .word 0xfffeb034
-
-WSPRDOG_VAL1:
- .word 0x0000aaaa
-WSPRDOG_VAL2:
- .word 0x00005555
-
-/* SDRAM config is: auto refresh enabled, 16 bit 4 bank,
- counter @8192 rows, 10 ns, 8 burst */
-REG_SDRAM_CONFIG:
- .word 0xfffecc20
-
-REG_SDRAM_MRS_LEGACY:
- .word 0xfffecc24
-
-REG_WATCHDOG:
- .word 0xfffec808
-
-REG_MPU_LOAD_TIMER:
- .word 0xfffec504
-REG_MPU_CNTL_TIMER:
- .word 0xfffec500
-
-/* Public and private rhea bridge registers definition */
-
-REG_RHEA_PUB_CTL:
- .word 0xFFFECA00
-
-REG_RHEA_PRIV_CTL:
- .word 0xFFFED300
-
-/* EMIFF SDRAM Configuration register
- - self refresh disable
- - auto refresh enabled
- - SDRAM type 64 Mb, 16 bits bus 4 banks
- - power down enabled
- - SDRAM clock disabled
- */
-SDRAM_CONFIG_VAL:
- .word 0x0C017DF4
-
-/* Burst full page length ; cas latency = 3 */
-SDRAM_MRS_VAL:
- .word 0x00000037
-
-VAL_ARM_CKCTL:
- .word 0x6505
-VAL_DPLL1_CTL:
- .word 0x3412
-
-#ifdef CONFIG_P2_OMAP730
-VAL_TC_EMIFS_CS0_CONFIG:
- .word 0x0000FFF3
-VAL_TC_EMIFS_CS1_CONFIG:
- .word 0x00004278
-VAL_TC_EMIFS_CS2_CONFIG:
- .word 0x00004278
-VAL_TC_EMIFS_CS3_CONFIG:
- .word 0x00004278
-VAL_TC_EMIFS_CS1_ADVANCED:
- .word 0x00000022
-#endif
-
-VAL_ARM_IDLECT1:
- .word 0x00000400
-VAL_ARM_IDLECT2:
- .word 0x00000886
-VAL_ARM_IDLECT3:
- .word 0x00000015
-
-WATCHDOG_VAL1:
- .word 0x000000f5
-WATCHDOG_VAL2:
- .word 0x000000a0
-
-VAL_MPU_LOAD_TIMER:
- .word 0xffffffff
-VAL_MPU_CNTL_TIMER:
- .word 0xffffffa1
-
-VAL_RHEA_CTL:
- .word 0xFF22
-
-/* Config Register vals */
-PERSEUS2_CONFIG_BASE:
- .word 0xFFFE1000
-
-.equ CONFIG_PCC_CONF, 0xB4
-.equ CONFIG_MODE1, 0x10
-.equ CONFIG_MODE2, 0x14
-.equ CONF_MOD_UART1_CLK_MODE_R, 0x0A
-
-/* misc values */
-.equ IRQ_MASK, 0x80 /* IRQ mask value */
-.equ FIQ_MASK, 0x40 /* FIQ mask value */
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2002
- * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#if defined(CONFIG_OMAP730)
-#include <./configs/omap730.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int test_boot_mode(void);
-void spin_up_leds(void);
-void flash__init (void);
-void ether__init (void);
-void set_muxconf_regs (void);
-void peripheral_power_enable (void);
-
-#define FLASH_ON_CS0 1
-#define FLASH_ON_CS3 0
-
-static inline void delay (unsigned long loops)
-{
- __asm__ volatile ("1:\n"
- "subs %0, %1, #1\n"
- "bne 1b":"=r" (loops):"0" (loops));
-}
-
-int test_boot_mode(void)
-{
- /* Check for CS0 and CS3 address decode swapping */
- if (*((volatile int *)EMIFS_CONFIG) & 0x00000002)
- return(FLASH_ON_CS3);
- else
- return(FLASH_ON_CS0);
-}
-
-/* Toggle backup LED indication */
-void toggle_backup_led(void)
-{
- static int backupLEDState = 0; /* Init variable so that the LED will be ON the first time */
- volatile unsigned int *IOConfReg;
-
-
- IOConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_5 + GPIO_DATA_OUTPUT);
-
- if (backupLEDState != 0) {
- *IOConfReg &= (0xFFFFEFFF);
- backupLEDState = 0;
- } else {
- *IOConfReg |= (0x00001000);
- backupLEDState = 1;
- }
-}
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-
-int board_init (void)
-{
- /* arch number of OMAP 730 P2 Board - Same as the Innovator! */
- gd->bd->bi_arch_number = MACH_TYPE_OMAP_PERSEUS2;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = 0x10000100;
-
- /* Configure MUX settings */
- set_muxconf_regs ();
-
- peripheral_power_enable ();
-
- /* Backup LED indication via GPIO_140 -> Red led if MUX correctly setup */
- toggle_backup_led();
-
- /* Hold GSM in reset until needed */
- *((volatile unsigned short *)M_CTL) &= ~1;
-
- /*
- * CSx timings, GPIO Mux ... setup
- */
-
- /* Flash: CS0 timings setup */
- *((volatile unsigned int *) FLASH_CFG_0) = 0x0000fff3;
- *((volatile unsigned int *) FLASH_ACFG_0_1) = 0x00000088;
-
- /* Ethernet support trough the debug board */
- /* CS1 timings setup */
- *((volatile unsigned int *) FLASH_CFG_1) = 0x0000fff3;
- *((volatile unsigned int *) FLASH_ACFG_0_1) = 0x00000000;
-
- /* this speeds up your boot a quite a bit. However to make it
- * work, you need make sure your kernel startup flush bug is fixed.
- * ... rkw ...
- */
- icache_enable ();
-
- flash__init ();
- ether__init ();
-
- return 0;
-}
-
-int misc_init_r (void)
-{
- /* currently empty */
- return (0);
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-void flash__init (void)
-{
- unsigned int regval;
-
- regval = *((volatile unsigned int *) EMIFS_CONFIG);
- /* Turn off write protection for flash devices. */
- regval = regval | 0x0001;
- *((volatile unsigned int *) EMIFS_CONFIG) = regval;
-}
-
-/*************************************************************
- Routine:ether__init
- Description: take the Ethernet controller out of reset and wait
- for the EEPROM load to complete.
-*************************************************************/
-void ether__init (void)
-{
-#define LAN_RESET_REGISTER 0x0400001c
-
- *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000;
- do {
- *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0001;
- udelay (100);
- } while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0001);
-
- do {
- *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000;
- udelay (100);
- } while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0000);
-
-#define ETH_CONTROL_REG 0x0400030b
-
- *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
- udelay (100);
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-int dram_init (void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
- return 0;
-}
-
-/******************************************************
- Routine: set_muxconf_regs
- Description: Setting up the configuration Mux registers
- specific to the hardware
-*******************************************************/
-void set_muxconf_regs (void)
-{
- volatile unsigned int *MuxConfReg;
- /* set each registers to its reset value; */
-
- /*
- * Backup LED Indication
- */
-
- /* Configure MUXed pin. Mode 6: GPIO_140 */
- MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF10);
- *MuxConfReg &= (0xFFFFFF1F); /* Clear D_MPU_LPG1 */
- *MuxConfReg |= 0x000000C0; /* Set D_MPU_LPG1 to 0x6 */
-
- /* Configure GPIO_140 as output */
- MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_5 + GPIO_DIRECTION_CONTROL);
- *MuxConfReg &= (0xFFFFEFFF); /* Clear direction (output) for GPIO 140 */
-
- /*
- * Configure GPIOs for battery charge & feedback
- */
-
- /* Configure MUXed pin. Mode 6: GPIO_35 */
- MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF3);
- *MuxConfReg &= 0xFFFFFFF1; /* Clear M_CLK_OUT */
- *MuxConfReg |= 0x0000000C; /* Set M_CLK_OUT = 0x6 (GPIOs) */
-
- /* Configure MUXed pin. Mode 6: GPIO_72,73,74 */
- MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF5);
- *MuxConfReg &= 0xFFFF1FFF; /* Clear D_DDR */
- *MuxConfReg |= 0x0000C000; /* Set D_DDR = 0x6 (GPIOs) */
-
- MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_3 + GPIO_DIRECTION_CONTROL);
- *MuxConfReg |= 0x00000100; /* Configure GPIO_72 as input */
- *MuxConfReg &= 0xFFFFFDFF; /* Configure GPIO_73 as output */
-
- /*
- * Allow battery charge
- */
-
- MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_3 + GPIO_DATA_OUTPUT);
- *MuxConfReg &= (0xFFFFFDFF); /* Clear GPIO_73 pin */
-
- /*
- * Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
- * It is used as the Ethernet controller interrupt
- */
- MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF9);
- *MuxConfReg &= 0x1FFFFFFF;
-}
-
-/******************************************************
- Routine: peripheral_power_enable
- Description: Enable the power for UART1
-*******************************************************/
-void peripheral_power_enable (void)
-{
- volatile unsigned int *MuxConfReg;
-
-
- /* Set up pins used by UART */
-
- /* Start UART clock (48MHz) */
- MuxConfReg = (volatile unsigned int *) (PERSEUS_PCC_CONF_REG);
- *MuxConfReg &= (0xFFFFFFF7);
- *MuxConfReg |= (0x00000008);
-
- /* Get the UART pin in mode0 */
- MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF3);
- *MuxConfReg &= (0xFF1FFFFF);
- *MuxConfReg &= (0xF1FFFFFF);
-}
--- /dev/null
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := beagle.o
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+/*
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ * Sunil Kumar <sunilsaini05@gmail.com>
+ * Shashi Ranjan <shashiranjanmca05@gmail.com>
+ *
+ * Derived from Beagle Board and 3430 SDP code by
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <twl4030.h>
+#include <asm/io.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/gpio.h>
+#include <asm/mach-types.h>
+#include "beagle.h"
+
+static int beagle_revision_c;
+
+/*
+ * Routine: board_init
+ * Description: Early hardware init.
+ */
+int board_init(void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
+ /* board id for Linux */
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP3_BEAGLE;
+ /* boot param addr */
+ gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+ return 0;
+}
+
+/*
+ * Routine: beagle_get_revision
+ * Description: Return the revision of the BeagleBoard this code is running on.
+ * If it is a revision Ax/Bx board, this function returns 0,
+ * on a revision C board you will get a 1.
+ */
+int beagle_get_revision(void)
+{
+ return beagle_revision_c;
+}
+
+/*
+ * Routine: beagle_identify
+ * Description: Detect if we are running on a Beagle revision Ax/Bx or
+ * Cx. This can be done by GPIO_171. If this is low, we are
+ * running on a revision C board.
+ */
+void beagle_identify(void)
+{
+ beagle_revision_c = 0;
+ if (!omap_request_gpio(171)) {
+ unsigned int val;
+
+ omap_set_gpio_direction(171, 1);
+ val = omap_get_gpio_datain(171);
+ omap_free_gpio(171);
+
+ if (val)
+ beagle_revision_c = 0;
+ else
+ beagle_revision_c = 1;
+ }
+
+ printf("Board revision ");
+ if (beagle_revision_c)
+ printf("C\n");
+ else
+ printf("Ax/Bx\n");
+}
+
+/*
+ * Routine: misc_init_r
+ * Description: Configure board specific parts
+ */
+int misc_init_r(void)
+{
+ struct gpio *gpio5_base = (struct gpio *)OMAP34XX_GPIO5_BASE;
+ struct gpio *gpio6_base = (struct gpio *)OMAP34XX_GPIO6_BASE;
+
+ twl4030_power_init();
+ twl4030_led_init();
+
+ /* Configure GPIOs to output */
+ writel(~(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1), &gpio6_base->oe);
+ writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
+ GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
+
+ /* Set GPIOs */
+ writel(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1,
+ &gpio6_base->setdataout);
+ writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
+ GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
+
+ beagle_identify();
+
+ dieid_num_r();
+
+ return 0;
+}
+
+/*
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
+ * hardware. Many pins need to be moved from protect to primary
+ * mode.
+ */
+void set_muxconf_regs(void)
+{
+ MUX_BEAGLE();
+
+ if (beagle_revision_c) {
+ MUX_BEAGLE_C();
+ }
+}
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Dirk Behme <dirk.behme@gmail.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _BEAGLE_H_
+#define _BEAGLE_H_
+
+const omap3_sysinfo sysinfo = {
+ DDR_STACKED,
+ "OMAP3 Beagle board",
+#if defined(CONFIG_ENV_IS_IN_ONENAND)
+ "OneNAND",
+#else
+ "NAND",
+#endif
+};
+
+#define BOARD_REVISION_MASK (0x1 << 11)
+
+/*
+ * IEN - Input Enable
+ * IDIS - Input Disable
+ * PTD - Pull type Down
+ * PTU - Pull type Up
+ * DIS - Pull type selection is inactive
+ * EN - Pull type selection is active
+ * M0 - Mode 0
+ * The commented string gives the final mux configuration for that pin
+ */
+#define MUX_BEAGLE() \
+ /*SDRC*/\
+ MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) /*SDRC_D0*/\
+ MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) /*SDRC_D1*/\
+ MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) /*SDRC_D2*/\
+ MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) /*SDRC_D3*/\
+ MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) /*SDRC_D4*/\
+ MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) /*SDRC_D5*/\
+ MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) /*SDRC_D6*/\
+ MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) /*SDRC_D7*/\
+ MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) /*SDRC_D8*/\
+ MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) /*SDRC_D9*/\
+ MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) /*SDRC_D10*/\
+ MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) /*SDRC_D11*/\
+ MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) /*SDRC_D12*/\
+ MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) /*SDRC_D13*/\
+ MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) /*SDRC_D14*/\
+ MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) /*SDRC_D15*/\
+ MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) /*SDRC_D16*/\
+ MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) /*SDRC_D17*/\
+ MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) /*SDRC_D18*/\
+ MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) /*SDRC_D19*/\
+ MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) /*SDRC_D20*/\
+ MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) /*SDRC_D21*/\
+ MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) /*SDRC_D22*/\
+ MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) /*SDRC_D23*/\
+ MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) /*SDRC_D24*/\
+ MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) /*SDRC_D25*/\
+ MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) /*SDRC_D26*/\
+ MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) /*SDRC_D27*/\
+ MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) /*SDRC_D28*/\
+ MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) /*SDRC_D29*/\
+ MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) /*SDRC_D30*/\
+ MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) /*SDRC_D31*/\
+ MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) /*SDRC_CLK*/\
+ MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) /*SDRC_DQS0*/\
+ MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) /*SDRC_DQS1*/\
+ MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) /*SDRC_DQS2*/\
+ MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) /*SDRC_DQS3*/\
+ /*GPMC*/\
+ MUX_VAL(CP(GPMC_A1), (IDIS | PTD | DIS | M0)) /*GPMC_A1*/\
+ MUX_VAL(CP(GPMC_A2), (IDIS | PTD | DIS | M0)) /*GPMC_A2*/\
+ MUX_VAL(CP(GPMC_A3), (IDIS | PTD | DIS | M0)) /*GPMC_A3*/\
+ MUX_VAL(CP(GPMC_A4), (IDIS | PTD | DIS | M0)) /*GPMC_A4*/\
+ MUX_VAL(CP(GPMC_A5), (IDIS | PTD | DIS | M0)) /*GPMC_A5*/\
+ MUX_VAL(CP(GPMC_A6), (IDIS | PTD | DIS | M0)) /*GPMC_A6*/\
+ MUX_VAL(CP(GPMC_A7), (IDIS | PTD | DIS | M0)) /*GPMC_A7*/\
+ MUX_VAL(CP(GPMC_A8), (IDIS | PTD | DIS | M0)) /*GPMC_A8*/\
+ MUX_VAL(CP(GPMC_A9), (IDIS | PTD | DIS | M0)) /*GPMC_A9*/\
+ MUX_VAL(CP(GPMC_A10), (IDIS | PTD | DIS | M0)) /*GPMC_A10*/\
+ MUX_VAL(CP(GPMC_D0), (IEN | PTD | DIS | M0)) /*GPMC_D0*/\
+ MUX_VAL(CP(GPMC_D1), (IEN | PTD | DIS | M0)) /*GPMC_D1*/\
+ MUX_VAL(CP(GPMC_D2), (IEN | PTD | DIS | M0)) /*GPMC_D2*/\
+ MUX_VAL(CP(GPMC_D3), (IEN | PTD | DIS | M0)) /*GPMC_D3*/\
+ MUX_VAL(CP(GPMC_D4), (IEN | PTD | DIS | M0)) /*GPMC_D4*/\
+ MUX_VAL(CP(GPMC_D5), (IEN | PTD | DIS | M0)) /*GPMC_D5*/\
+ MUX_VAL(CP(GPMC_D6), (IEN | PTD | DIS | M0)) /*GPMC_D6*/\
+ MUX_VAL(CP(GPMC_D7), (IEN | PTD | DIS | M0)) /*GPMC_D7*/\
+ MUX_VAL(CP(GPMC_D8), (IEN | PTD | DIS | M0)) /*GPMC_D8*/\
+ MUX_VAL(CP(GPMC_D9), (IEN | PTD | DIS | M0)) /*GPMC_D9*/\
+ MUX_VAL(CP(GPMC_D10), (IEN | PTD | DIS | M0)) /*GPMC_D10*/\
+ MUX_VAL(CP(GPMC_D11), (IEN | PTD | DIS | M0)) /*GPMC_D11*/\
+ MUX_VAL(CP(GPMC_D12), (IEN | PTD | DIS | M0)) /*GPMC_D12*/\
+ MUX_VAL(CP(GPMC_D13), (IEN | PTD | DIS | M0)) /*GPMC_D13*/\
+ MUX_VAL(CP(GPMC_D14), (IEN | PTD | DIS | M0)) /*GPMC_D14*/\
+ MUX_VAL(CP(GPMC_D15), (IEN | PTD | DIS | M0)) /*GPMC_D15*/\
+ MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) /*GPMC_nCS0*/\
+ MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M0)) /*GPMC_nCS1*/\
+ MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M0)) /*GPMC_nCS2*/\
+ MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M0)) /*GPMC_nCS3*/\
+ MUX_VAL(CP(GPMC_NCS4), (IDIS | PTU | EN | M0)) /*GPMC_nCS4*/\
+ MUX_VAL(CP(GPMC_NCS5), (IDIS | PTD | DIS | M0)) /*GPMC_nCS5*/\
+ MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M1)) /*SYS_nDMA_REQ2*/\
+ MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M1)) /*SYS_nDMA_REQ3*/\
+ MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | DIS | M0)) /*GPMC_nBE1*/\
+ MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M0)) /*GPMC_WAIT2*/\
+ MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0)) /*GPMC_WAIT3*/\
+ MUX_VAL(CP(GPMC_CLK), (IDIS | PTD | DIS | M0)) /*GPMC_CLK*/\
+ MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /*GPMC_nADV_ALE*/\
+ MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /*GPMC_nOE*/\
+ MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /*GPMC_nWE*/\
+ MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTD | DIS | M0)) /*GPMC_nBE0_CLE*/\
+ MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0)) /*GPMC_nWP*/\
+ MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) /*GPMC_WAIT0*/\
+ MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) /*GPMC_WAIT1*/\
+ /*DSS*/\
+ MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
+ MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0)) /*DSS_HSYNC*/\
+ MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0)) /*DSS_VSYNC*/\
+ MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0)) /*DSS_ACBIAS*/\
+ MUX_VAL(CP(DSS_DATA0), (IDIS | PTD | DIS | M0)) /*DSS_DATA0*/\
+ MUX_VAL(CP(DSS_DATA1), (IDIS | PTD | DIS | M0)) /*DSS_DATA1*/\
+ MUX_VAL(CP(DSS_DATA2), (IDIS | PTD | DIS | M0)) /*DSS_DATA2*/\
+ MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M0)) /*DSS_DATA3*/\
+ MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M0)) /*DSS_DATA4*/\
+ MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M0)) /*DSS_DATA5*/\
+ MUX_VAL(CP(DSS_DATA6), (IDIS | PTD | DIS | M0)) /*DSS_DATA6*/\
+ MUX_VAL(CP(DSS_DATA7), (IDIS | PTD | DIS | M0)) /*DSS_DATA7*/\
+ MUX_VAL(CP(DSS_DATA8), (IDIS | PTD | DIS | M0)) /*DSS_DATA8*/\
+ MUX_VAL(CP(DSS_DATA9), (IDIS | PTD | DIS | M0)) /*DSS_DATA9*/\
+ MUX_VAL(CP(DSS_DATA10), (IDIS | PTD | DIS | M0)) /*DSS_DATA10*/\
+ MUX_VAL(CP(DSS_DATA11), (IDIS | PTD | DIS | M0)) /*DSS_DATA11*/\
+ MUX_VAL(CP(DSS_DATA12), (IDIS | PTD | DIS | M0)) /*DSS_DATA12*/\
+ MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | DIS | M0)) /*DSS_DATA13*/\
+ MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | DIS | M0)) /*DSS_DATA14*/\
+ MUX_VAL(CP(DSS_DATA15), (IDIS | PTD | DIS | M0)) /*DSS_DATA15*/\
+ MUX_VAL(CP(DSS_DATA16), (IDIS | PTD | DIS | M0)) /*DSS_DATA16*/\
+ MUX_VAL(CP(DSS_DATA17), (IDIS | PTD | DIS | M0)) /*DSS_DATA17*/\
+ MUX_VAL(CP(DSS_DATA18), (IDIS | PTD | DIS | M0)) /*DSS_DATA18*/\
+ MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M0)) /*DSS_DATA19*/\
+ MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M0)) /*DSS_DATA20*/\
+ MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M0)) /*DSS_DATA21*/\
+ MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0)) /*DSS_DATA22*/\
+ MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0)) /*DSS_DATA23*/\
+ /*CAMERA*/\
+ MUX_VAL(CP(CAM_HS), (IEN | PTU | EN | M0)) /*CAM_HS */\
+ MUX_VAL(CP(CAM_VS), (IEN | PTU | EN | M0)) /*CAM_VS */\
+ MUX_VAL(CP(CAM_XCLKA), (IDIS | PTD | DIS | M0)) /*CAM_XCLKA*/\
+ MUX_VAL(CP(CAM_PCLK), (IEN | PTU | EN | M0)) /*CAM_PCLK*/\
+ MUX_VAL(CP(CAM_FLD), (IDIS | PTD | DIS | M4)) /*GPIO_98*/\
+ MUX_VAL(CP(CAM_D0), (IEN | PTD | DIS | M0)) /*CAM_D0*/\
+ MUX_VAL(CP(CAM_D1), (IEN | PTD | DIS | M0)) /*CAM_D1*/\
+ MUX_VAL(CP(CAM_D2), (IEN | PTD | DIS | M0)) /*CAM_D2*/\
+ MUX_VAL(CP(CAM_D3), (IEN | PTD | DIS | M0)) /*CAM_D3*/\
+ MUX_VAL(CP(CAM_D4), (IEN | PTD | DIS | M0)) /*CAM_D4*/\
+ MUX_VAL(CP(CAM_D5), (IEN | PTD | DIS | M0)) /*CAM_D5*/\
+ MUX_VAL(CP(CAM_D6), (IEN | PTD | DIS | M0)) /*CAM_D6*/\
+ MUX_VAL(CP(CAM_D7), (IEN | PTD | DIS | M0)) /*CAM_D7*/\
+ MUX_VAL(CP(CAM_D8), (IEN | PTD | DIS | M0)) /*CAM_D8*/\
+ MUX_VAL(CP(CAM_D9), (IEN | PTD | DIS | M0)) /*CAM_D9*/\
+ MUX_VAL(CP(CAM_D10), (IEN | PTD | DIS | M0)) /*CAM_D10*/\
+ MUX_VAL(CP(CAM_D11), (IEN | PTD | DIS | M0)) /*CAM_D11*/\
+ MUX_VAL(CP(CAM_XCLKB), (IDIS | PTD | DIS | M0)) /*CAM_XCLKB*/\
+ MUX_VAL(CP(CAM_WEN), (IEN | PTD | DIS | M4)) /*GPIO_167*/\
+ MUX_VAL(CP(CAM_STROBE), (IDIS | PTD | DIS | M0)) /*CAM_STROBE*/\
+ MUX_VAL(CP(CSI2_DX0), (IEN | PTD | DIS | M0)) /*CSI2_DX0*/\
+ MUX_VAL(CP(CSI2_DY0), (IEN | PTD | DIS | M0)) /*CSI2_DY0*/\
+ MUX_VAL(CP(CSI2_DX1), (IEN | PTD | DIS | M0)) /*CSI2_DX1*/\
+ MUX_VAL(CP(CSI2_DY1), (IEN | PTD | DIS | M0)) /*CSI2_DY1*/\
+ /*Audio Interface */\
+ MUX_VAL(CP(MCBSP2_FSX), (IEN | PTD | DIS | M0)) /*McBSP2_FSX*/\
+ MUX_VAL(CP(MCBSP2_CLKX), (IEN | PTD | DIS | M0)) /*McBSP2_CLKX*/\
+ MUX_VAL(CP(MCBSP2_DR), (IEN | PTD | DIS | M0)) /*McBSP2_DR*/\
+ MUX_VAL(CP(MCBSP2_DX), (IDIS | PTD | DIS | M0)) /*McBSP2_DX*/\
+ /*Expansion card */\
+ MUX_VAL(CP(MMC1_CLK), (IDIS | PTU | EN | M0)) /*MMC1_CLK*/\
+ MUX_VAL(CP(MMC1_CMD), (IEN | PTU | EN | M0)) /*MMC1_CMD*/\
+ MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | EN | M0)) /*MMC1_DAT0*/\
+ MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | EN | M0)) /*MMC1_DAT1*/\
+ MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | EN | M0)) /*MMC1_DAT2*/\
+ MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | EN | M0)) /*MMC1_DAT3*/\
+ MUX_VAL(CP(MMC1_DAT4), (IEN | PTU | EN | M0)) /*MMC1_DAT4*/\
+ MUX_VAL(CP(MMC1_DAT5), (IEN | PTU | EN | M0)) /*MMC1_DAT5*/\
+ MUX_VAL(CP(MMC1_DAT6), (IEN | PTU | EN | M0)) /*MMC1_DAT6*/\
+ MUX_VAL(CP(MMC1_DAT7), (IEN | PTU | EN | M0)) /*MMC1_DAT7*/\
+ /*Wireless LAN */\
+ MUX_VAL(CP(MMC2_CLK), (IEN | PTU | EN | M4)) /*GPIO_130*/\
+ MUX_VAL(CP(MMC2_CMD), (IEN | PTU | EN | M4)) /*GPIO_131*/\
+ MUX_VAL(CP(MMC2_DAT0), (IEN | PTU | EN | M4)) /*GPIO_132*/\
+ MUX_VAL(CP(MMC2_DAT1), (IEN | PTU | EN | M4)) /*GPIO_133*/\
+ MUX_VAL(CP(MMC2_DAT2), (IEN | PTU | EN | M4)) /*GPIO_134*/\
+ MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | EN | M4)) /*GPIO_135*/\
+ MUX_VAL(CP(MMC2_DAT4), (IEN | PTU | EN | M4)) /*GPIO_136*/\
+ MUX_VAL(CP(MMC2_DAT5), (IEN | PTU | EN | M4)) /*GPIO_137*/\
+ MUX_VAL(CP(MMC2_DAT6), (IEN | PTU | EN | M4)) /*GPIO_138*/\
+ MUX_VAL(CP(MMC2_DAT7), (IEN | PTU | EN | M4)) /*GPIO_139*/\
+ /*Bluetooth*/\
+ MUX_VAL(CP(MCBSP3_DX), (IEN | PTD | DIS | M1)) /*UART2_CTS*/\
+ MUX_VAL(CP(MCBSP3_DR), (IDIS | PTD | DIS | M1)) /*UART2_RTS*/\
+ MUX_VAL(CP(MCBSP3_CLKX), (IDIS | PTD | DIS | M1)) /*UART2_TX*/\
+ MUX_VAL(CP(MCBSP3_FSX), (IEN | PTD | DIS | M1)) /*UART2_RX*/\
+ MUX_VAL(CP(UART2_CTS), (IEN | PTD | DIS | M4)) /*GPIO_144*/\
+ MUX_VAL(CP(UART2_RTS), (IEN | PTD | DIS | M4)) /*GPIO_145*/\
+ MUX_VAL(CP(UART2_TX), (IEN | PTD | DIS | M4)) /*GPIO_146*/\
+ MUX_VAL(CP(UART2_RX), (IEN | PTD | DIS | M4)) /*GPIO_147*/\
+ /*Modem Interface */\
+ MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0)) /*UART1_TX*/\
+ MUX_VAL(CP(UART1_RTS), (IDIS | PTD | DIS | M4)) /*GPIO_149*/ \
+ MUX_VAL(CP(UART1_CTS), (IDIS | PTD | DIS | M4)) /*GPIO_150*/ \
+ MUX_VAL(CP(UART1_RX), (IEN | PTD | DIS | M0)) /*UART1_RX*/\
+ MUX_VAL(CP(MCBSP4_CLKX), (IEN | PTD | DIS | M1)) /*SSI1_DAT_RX*/\
+ MUX_VAL(CP(MCBSP4_DR), (IEN | PTD | DIS | M1)) /*SSI1_FLAG_RX*/\
+ MUX_VAL(CP(MCBSP4_DX), (IEN | PTD | DIS | M1)) /*SSI1_RDY_RX*/\
+ MUX_VAL(CP(MCBSP4_FSX), (IEN | PTD | DIS | M1)) /*SSI1_WAKE*/\
+ MUX_VAL(CP(MCBSP1_CLKR), (IDIS | PTD | DIS | M4)) /*GPIO_156*/\
+ MUX_VAL(CP(MCBSP1_FSR), (IDIS | PTU | EN | M4)) /*GPIO_157*/\
+ MUX_VAL(CP(MCBSP1_DX), (IDIS | PTD | DIS | M4)) /*GPIO_158*/\
+ MUX_VAL(CP(MCBSP1_DR), (IDIS | PTD | DIS | M4)) /*GPIO_159*/\
+ MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0)) /*McBSP_CLKS*/\
+ MUX_VAL(CP(MCBSP1_FSX), (IDIS | PTD | DIS | M4)) /*GPIO_161*/\
+ MUX_VAL(CP(MCBSP1_CLKX), (IDIS | PTD | DIS | M4)) /*GPIO_162*/\
+ /*Serial Interface*/\
+ MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTD | EN | M0)) /*UART3_CTS_RCTX*/\
+ MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTD | DIS | M0)) /*UART3_RTS_SD */\
+ MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0)) /*UART3_RX_IRRX*/\
+ MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0)) /*UART3_TX_IRTX*/\
+ MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0)) /*HSUSB0_CLK*/\
+ MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0)) /*HSUSB0_STP*/\
+ MUX_VAL(CP(HSUSB0_DIR), (IEN | PTD | DIS | M0)) /*HSUSB0_DIR*/\
+ MUX_VAL(CP(HSUSB0_NXT), (IEN | PTD | DIS | M0)) /*HSUSB0_NXT*/\
+ MUX_VAL(CP(HSUSB0_DATA0), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA0*/\
+ MUX_VAL(CP(HSUSB0_DATA1), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA1*/\
+ MUX_VAL(CP(HSUSB0_DATA2), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA2*/\
+ MUX_VAL(CP(HSUSB0_DATA3), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA3*/\
+ MUX_VAL(CP(HSUSB0_DATA4), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA4*/\
+ MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA5*/\
+ MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA6*/\
+ MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA7*/\
+ MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)) /*I2C1_SCL*/\
+ MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)) /*I2C1_SDA*/\
+ MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M4)) /*GPIO_168*/\
+ MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M4)) /*GPIO_183*/\
+ MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0)) /*I2C3_SCL*/\
+ MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0)) /*I2C3_SDA*/\
+ MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0)) /*I2C4_SCL*/\
+ MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0)) /*I2C4_SDA*/\
+ MUX_VAL(CP(HDQ_SIO), (IDIS | PTU | EN | M4)) /*GPIO_170*/\
+ MUX_VAL(CP(MCSPI1_CLK), (IEN | PTU | EN | M4)) /*GPIO_171*/\
+ MUX_VAL(CP(MCSPI1_SIMO), (IEN | PTU | EN | M4)) /*GPIO_172*/\
+ MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | DIS | M0)) /*McSPI1_SOMI*/\
+ MUX_VAL(CP(MCSPI1_CS0), (IEN | PTD | EN | M0)) /*McSPI1_CS0*/\
+ MUX_VAL(CP(MCSPI1_CS1), (IDIS | PTD | EN | M0)) /*McSPI1_CS1*/\
+ MUX_VAL(CP(MCSPI1_CS2), (IDIS | PTD | DIS | M4)) /*GPIO_176*/\
+ /* USB EHCI (port 2) */\
+ MUX_VAL(CP(MCSPI1_CS3), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA2*/\
+ MUX_VAL(CP(MCSPI2_CLK), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA7*/\
+ MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA4*/\
+ MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA5*/\
+ MUX_VAL(CP(MCSPI2_CS0), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA6*/\
+ MUX_VAL(CP(MCSPI2_CS1), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA3*/\
+ MUX_VAL(CP(ETK_D10_ES2), (IDIS | PTU | DIS | M3)) /*HSUSB2_CLK*/\
+ MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTU | DIS | M3)) /*HSUSB2_STP*/\
+ MUX_VAL(CP(ETK_D12_ES2), (IEN | PTU | DIS | M3)) /*HSUSB2_DIR*/\
+ MUX_VAL(CP(ETK_D13_ES2), (IEN | PTU | DIS | M3)) /*HSUSB2_NXT*/\
+ MUX_VAL(CP(ETK_D14_ES2), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA0*/\
+ MUX_VAL(CP(ETK_D15_ES2), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA1*/\
+ /*Control and debug */\
+ MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0)) /*SYS_32K*/\
+ MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) /*SYS_CLKREQ*/\
+ MUX_VAL(CP(SYS_NIRQ), (IEN | PTU | EN | M0)) /*SYS_nIRQ*/\
+ MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4)) /*GPIO_2*/\
+ MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4)) /*GPIO_3*/\
+ MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /*GPIO_4 - MMC1_WP*/\
+ MUX_VAL(CP(SYS_BOOT3), (IEN | PTD | DIS | M4)) /*GPIO_5*/\
+ MUX_VAL(CP(SYS_BOOT4), (IEN | PTD | DIS | M4)) /*GPIO_6*/\
+ MUX_VAL(CP(SYS_BOOT5), (IEN | PTD | DIS | M4)) /*GPIO_7*/\
+ MUX_VAL(CP(SYS_BOOT6), (IDIS | PTD | DIS | M4)) /*GPIO_8*/ \
+ MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0)) /*SYS_OFF_MODE*/\
+ MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M0)) /*SYS_CLKOUT1*/\
+ MUX_VAL(CP(SYS_CLKOUT2), (IEN | PTU | EN | M4)) /*GPIO_186*/\
+ MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | EN | M3)) /*HSUSB1_STP*/\
+ MUX_VAL(CP(ETK_CTL_ES2), (IDIS | PTU | DIS | M3)) /*HSUSB1_CLK*/\
+ MUX_VAL(CP(ETK_D0_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA0*/\
+ MUX_VAL(CP(ETK_D1_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA1*/\
+ MUX_VAL(CP(ETK_D2_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA2*/\
+ MUX_VAL(CP(ETK_D3_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA7*/\
+ MUX_VAL(CP(ETK_D4_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA4*/\
+ MUX_VAL(CP(ETK_D5_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA5*/\
+ MUX_VAL(CP(ETK_D6_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA6*/\
+ MUX_VAL(CP(ETK_D7_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA3*/\
+ MUX_VAL(CP(ETK_D8_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DIR*/\
+ MUX_VAL(CP(ETK_D9_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_NXT*/\
+ MUX_VAL(CP(D2D_MCAD1), (IEN | PTD | EN | M0)) /*d2d_mcad1*/\
+ MUX_VAL(CP(D2D_MCAD2), (IEN | PTD | EN | M0)) /*d2d_mcad2*/\
+ MUX_VAL(CP(D2D_MCAD3), (IEN | PTD | EN | M0)) /*d2d_mcad3*/\
+ MUX_VAL(CP(D2D_MCAD4), (IEN | PTD | EN | M0)) /*d2d_mcad4*/\
+ MUX_VAL(CP(D2D_MCAD5), (IEN | PTD | EN | M0)) /*d2d_mcad5*/\
+ MUX_VAL(CP(D2D_MCAD6), (IEN | PTD | EN | M0)) /*d2d_mcad6*/\
+ MUX_VAL(CP(D2D_MCAD7), (IEN | PTD | EN | M0)) /*d2d_mcad7*/\
+ MUX_VAL(CP(D2D_MCAD8), (IEN | PTD | EN | M0)) /*d2d_mcad8*/\
+ MUX_VAL(CP(D2D_MCAD9), (IEN | PTD | EN | M0)) /*d2d_mcad9*/\
+ MUX_VAL(CP(D2D_MCAD10), (IEN | PTD | EN | M0)) /*d2d_mcad10*/\
+ MUX_VAL(CP(D2D_MCAD11), (IEN | PTD | EN | M0)) /*d2d_mcad11*/\
+ MUX_VAL(CP(D2D_MCAD12), (IEN | PTD | EN | M0)) /*d2d_mcad12*/\
+ MUX_VAL(CP(D2D_MCAD13), (IEN | PTD | EN | M0)) /*d2d_mcad13*/\
+ MUX_VAL(CP(D2D_MCAD14), (IEN | PTD | EN | M0)) /*d2d_mcad14*/\
+ MUX_VAL(CP(D2D_MCAD15), (IEN | PTD | EN | M0)) /*d2d_mcad15*/\
+ MUX_VAL(CP(D2D_MCAD16), (IEN | PTD | EN | M0)) /*d2d_mcad16*/\
+ MUX_VAL(CP(D2D_MCAD17), (IEN | PTD | EN | M0)) /*d2d_mcad17*/\
+ MUX_VAL(CP(D2D_MCAD18), (IEN | PTD | EN | M0)) /*d2d_mcad18*/\
+ MUX_VAL(CP(D2D_MCAD19), (IEN | PTD | EN | M0)) /*d2d_mcad19*/\
+ MUX_VAL(CP(D2D_MCAD20), (IEN | PTD | EN | M0)) /*d2d_mcad20*/\
+ MUX_VAL(CP(D2D_MCAD21), (IEN | PTD | EN | M0)) /*d2d_mcad21*/\
+ MUX_VAL(CP(D2D_MCAD22), (IEN | PTD | EN | M0)) /*d2d_mcad22*/\
+ MUX_VAL(CP(D2D_MCAD23), (IEN | PTD | EN | M0)) /*d2d_mcad23*/\
+ MUX_VAL(CP(D2D_MCAD24), (IEN | PTD | EN | M0)) /*d2d_mcad24*/\
+ MUX_VAL(CP(D2D_MCAD25), (IEN | PTD | EN | M0)) /*d2d_mcad25*/\
+ MUX_VAL(CP(D2D_MCAD26), (IEN | PTD | EN | M0)) /*d2d_mcad26*/\
+ MUX_VAL(CP(D2D_MCAD27), (IEN | PTD | EN | M0)) /*d2d_mcad27*/\
+ MUX_VAL(CP(D2D_MCAD28), (IEN | PTD | EN | M0)) /*d2d_mcad28*/\
+ MUX_VAL(CP(D2D_MCAD29), (IEN | PTD | EN | M0)) /*d2d_mcad29*/\
+ MUX_VAL(CP(D2D_MCAD30), (IEN | PTD | EN | M0)) /*d2d_mcad30*/\
+ MUX_VAL(CP(D2D_MCAD31), (IEN | PTD | EN | M0)) /*d2d_mcad31*/\
+ MUX_VAL(CP(D2D_MCAD32), (IEN | PTD | EN | M0)) /*d2d_mcad32*/\
+ MUX_VAL(CP(D2D_MCAD33), (IEN | PTD | EN | M0)) /*d2d_mcad33*/\
+ MUX_VAL(CP(D2D_MCAD34), (IEN | PTD | EN | M0)) /*d2d_mcad34*/\
+ MUX_VAL(CP(D2D_MCAD35), (IEN | PTD | EN | M0)) /*d2d_mcad35*/\
+ MUX_VAL(CP(D2D_MCAD36), (IEN | PTD | EN | M0)) /*d2d_mcad36*/\
+ MUX_VAL(CP(D2D_CLK26MI), (IEN | PTD | DIS | M0)) /*d2d_clk26mi*/\
+ MUX_VAL(CP(D2D_NRESPWRON), (IEN | PTD | EN | M0)) /*d2d_nrespwron*/\
+ MUX_VAL(CP(D2D_NRESWARM), (IEN | PTU | EN | M0)) /*d2d_nreswarm */\
+ MUX_VAL(CP(D2D_ARM9NIRQ), (IEN | PTD | DIS | M0)) /*d2d_arm9nirq */\
+ MUX_VAL(CP(D2D_UMA2P6FIQ), (IEN | PTD | DIS | M0)) /*d2d_uma2p6fiq*/\
+ MUX_VAL(CP(D2D_SPINT), (IEN | PTD | EN | M0)) /*d2d_spint*/\
+ MUX_VAL(CP(D2D_FRINT), (IEN | PTD | EN | M0)) /*d2d_frint*/\
+ MUX_VAL(CP(D2D_DMAREQ0), (IEN | PTD | DIS | M0)) /*d2d_dmareq0*/\
+ MUX_VAL(CP(D2D_DMAREQ1), (IEN | PTD | DIS | M0)) /*d2d_dmareq1*/\
+ MUX_VAL(CP(D2D_DMAREQ2), (IEN | PTD | DIS | M0)) /*d2d_dmareq2*/\
+ MUX_VAL(CP(D2D_DMAREQ3), (IEN | PTD | DIS | M0)) /*d2d_dmareq3*/\
+ MUX_VAL(CP(D2D_N3GTRST), (IEN | PTD | DIS | M0)) /*d2d_n3gtrst*/\
+ MUX_VAL(CP(D2D_N3GTDI), (IEN | PTD | DIS | M0)) /*d2d_n3gtdi*/\
+ MUX_VAL(CP(D2D_N3GTDO), (IEN | PTD | DIS | M0)) /*d2d_n3gtdo*/\
+ MUX_VAL(CP(D2D_N3GTMS), (IEN | PTD | DIS | M0)) /*d2d_n3gtms*/\
+ MUX_VAL(CP(D2D_N3GTCK), (IEN | PTD | DIS | M0)) /*d2d_n3gtck*/\
+ MUX_VAL(CP(D2D_N3GRTCK), (IEN | PTD | DIS | M0)) /*d2d_n3grtck*/\
+ MUX_VAL(CP(D2D_MSTDBY), (IEN | PTU | EN | M0)) /*d2d_mstdby*/\
+ MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0)) /*d2d_swakeup*/\
+ MUX_VAL(CP(D2D_IDLEREQ), (IEN | PTD | DIS | M0)) /*d2d_idlereq*/\
+ MUX_VAL(CP(D2D_IDLEACK), (IEN | PTU | EN | M0)) /*d2d_idleack*/\
+ MUX_VAL(CP(D2D_MWRITE), (IEN | PTD | DIS | M0)) /*d2d_mwrite*/\
+ MUX_VAL(CP(D2D_SWRITE), (IEN | PTD | DIS | M0)) /*d2d_swrite*/\
+ MUX_VAL(CP(D2D_MREAD), (IEN | PTD | DIS | M0)) /*d2d_mread*/\
+ MUX_VAL(CP(D2D_SREAD), (IEN | PTD | DIS | M0)) /*d2d_sread*/\
+ MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_mbusflag*/\
+ MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_sbusflag*/\
+ MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0)) /*sdrc_cke0*/\
+ MUX_VAL(CP(SDRC_CKE1), (IDIS | PTU | EN | M0)) /*sdrc_cke1*/
+
+#define MUX_BEAGLE_C() \
+ MUX_VAL(CP(MCBSP3_DX), (IEN | PTD | DIS | M4)) /*GPIO_140*/\
+ MUX_VAL(CP(MCBSP3_DR), (IEN | PTD | DIS | M4)) /*GPIO_142*/\
+ MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTD | DIS | M4)) /*GPIO_141*/\
+ MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M0)) /*UART2_CTS*/\
+ MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M0)) /*UART2_RTS*/\
+ MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M0)) /*UART2_TX*/
+
+#endif
--- /dev/null
+#
+# (C) Copyright 2006
+# Texas Instruments, <www.ti.com>
+#
+# Beagle Board uses OMAP3 (ARM-CortexA8) cpu
+# see http://www.ti.com/ for more information on Texas Instruments
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# Physical Address:
+# 8000'0000 (bank0)
+# A000/0000 (bank1)
+# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+
+# For use with external or internal boots.
+TEXT_BASE = 0x80e80000
--- /dev/null
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := evm.o
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
--- /dev/null
+#
+# (C) Copyright 2006 - 2008
+# Texas Instruments, <www.ti.com>
+#
+# EVM uses OMAP3 (ARM-CortexA8) cpu
+# see http://www.ti.com/ for more information on Texas Instruments
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# Physical Address:
+# 8000'0000 (bank0)
+# A000/0000 (bank1)
+# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+
+# For use with external or internal boots.
+TEXT_BASE = 0x80e80000
--- /dev/null
+/*
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ * Manikandan Pillai <mani.pillai@ti.com>
+ *
+ * Derived from Beagle Board and 3430 SDP code by
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <i2c.h>
+#include <asm/mach-types.h>
+#include "evm.h"
+
+/*
+ * Routine: board_init
+ * Description: Early hardware init.
+ */
+int board_init(void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
+ /* board id for Linux */
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP3EVM;
+ /* boot param addr */
+ gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+ return 0;
+}
+
+/*
+ * Routine: misc_init_r
+ * Description: Init ethernet (done here so udelay works)
+ */
+int misc_init_r(void)
+{
+
+#ifdef CONFIG_DRIVER_OMAP34XX_I2C
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+#endif
+
+#if defined(CONFIG_CMD_NET)
+ setup_net_chip();
+#endif
+
+ dieid_num_r();
+
+ return 0;
+}
+
+/*
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
+ * hardware. Many pins need to be moved from protect to primary
+ * mode.
+ */
+void set_muxconf_regs(void)
+{
+ MUX_EVM();
+}
+
+/*
+ * Routine: setup_net_chip
+ * Description: Setting up the configuration GPMC registers specific to the
+ * Ethernet hardware.
+ */
+static void setup_net_chip(void)
+{
+ struct gpio *gpio3_base = (struct gpio *)OMAP34XX_GPIO3_BASE;
+ struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE;
+
+ /* Configure GPMC registers */
+ writel(NET_GPMC_CONFIG1, &gpmc_cfg->cs[5].config1);
+ writel(NET_GPMC_CONFIG2, &gpmc_cfg->cs[5].config2);
+ writel(NET_GPMC_CONFIG3, &gpmc_cfg->cs[5].config3);
+ writel(NET_GPMC_CONFIG4, &gpmc_cfg->cs[5].config4);
+ writel(NET_GPMC_CONFIG5, &gpmc_cfg->cs[5].config5);
+ writel(NET_GPMC_CONFIG6, &gpmc_cfg->cs[5].config6);
+ writel(NET_GPMC_CONFIG7, &gpmc_cfg->cs[5].config7);
+
+ /* Enable off mode for NWE in PADCONF_GPMC_NWE register */
+ writew(readw(&ctrl_base ->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe);
+ /* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */
+ writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe);
+ /* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */
+ writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00,
+ &ctrl_base->gpmc_nadv_ale);
+
+ /* Make GPIO 64 as output pin */
+ writel(readl(&gpio3_base->oe) & ~(GPIO0), &gpio3_base->oe);
+
+ /* Now send a pulse on the GPIO pin */
+ writel(GPIO0, &gpio3_base->setdataout);
+ udelay(1);
+ writel(GPIO0, &gpio3_base->cleardataout);
+ udelay(1);
+ writel(GPIO0, &gpio3_base->setdataout);
+}
+
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0;
+#ifdef CONFIG_SMC911X
+ rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
+#endif
+ return rc;
+}
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Nishanth Menon <menon.nishanth@gmail.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _EVM_H_
+#define _EVM_H_
+
+const omap3_sysinfo sysinfo = {
+ DDR_DISCRETE,
+ "OMAP3 EVM board",
+#if defined(CONFIG_ENV_IS_IN_ONENAND)
+ "OneNAND",
+#else
+ "NAND",
+#endif
+};
+
+static void setup_net_chip(void);
+
+/*
+ * IEN - Input Enable
+ * IDIS - Input Disable
+ * PTD - Pull type Down
+ * PTU - Pull type Up
+ * DIS - Pull type selection is inactive
+ * EN - Pull type selection is active
+ * M0 - Mode 0
+ * The commented string gives the final mux configuration for that pin
+ */
+#define MUX_EVM() \
+ /*SDRC*/\
+ MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) /*SDRC_D0*/\
+ MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) /*SDRC_D1*/\
+ MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) /*SDRC_D2*/\
+ MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) /*SDRC_D3*/\
+ MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) /*SDRC_D4*/\
+ MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) /*SDRC_D5*/\
+ MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) /*SDRC_D6*/\
+ MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) /*SDRC_D7*/\
+ MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) /*SDRC_D8*/\
+ MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) /*SDRC_D9*/\
+ MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) /*SDRC_D10*/\
+ MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) /*SDRC_D11*/\
+ MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) /*SDRC_D12*/\
+ MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) /*SDRC_D13*/\
+ MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) /*SDRC_D14*/\
+ MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) /*SDRC_D15*/\
+ MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) /*SDRC_D16*/\
+ MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) /*SDRC_D17*/\
+ MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) /*SDRC_D18*/\
+ MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) /*SDRC_D19*/\
+ MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) /*SDRC_D20*/\
+ MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) /*SDRC_D21*/\
+ MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) /*SDRC_D22*/\
+ MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) /*SDRC_D23*/\
+ MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) /*SDRC_D24*/\
+ MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) /*SDRC_D25*/\
+ MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) /*SDRC_D26*/\
+ MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) /*SDRC_D27*/\
+ MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) /*SDRC_D28*/\
+ MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) /*SDRC_D29*/\
+ MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) /*SDRC_D30*/\
+ MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) /*SDRC_D31*/\
+ MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) /*SDRC_CLK*/\
+ MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) /*SDRC_DQS0*/\
+ MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) /*SDRC_DQS1*/\
+ MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) /*SDRC_DQS2*/\
+ MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) /*SDRC_DQS3*/\
+ /*GPMC*/\
+ MUX_VAL(CP(GPMC_A1), (IDIS | PTU | EN | M0)) /*GPMC_A1*/\
+ MUX_VAL(CP(GPMC_A2), (IDIS | PTU | EN | M0)) /*GPMC_A2*/\
+ MUX_VAL(CP(GPMC_A3), (IDIS | PTU | EN | M0)) /*GPMC_A3*/\
+ MUX_VAL(CP(GPMC_A4), (IDIS | PTU | EN | M0)) /*GPMC_A4*/\
+ MUX_VAL(CP(GPMC_A5), (IDIS | PTU | EN | M0)) /*GPMC_A5*/\
+ MUX_VAL(CP(GPMC_A6), (IDIS | PTU | EN | M0)) /*GPMC_A6*/\
+ MUX_VAL(CP(GPMC_A7), (IDIS | PTU | EN | M0)) /*GPMC_A7*/\
+ MUX_VAL(CP(GPMC_A8), (IDIS | PTU | EN | M0)) /*GPMC_A8*/\
+ MUX_VAL(CP(GPMC_A9), (IDIS | PTU | EN | M0)) /*GPMC_A9*/\
+ MUX_VAL(CP(GPMC_A10), (IDIS | PTU | EN | M0)) /*GPMC_A10*/\
+ MUX_VAL(CP(GPMC_D0), (IEN | PTU | EN | M0)) /*GPMC_D0*/\
+ MUX_VAL(CP(GPMC_D1), (IEN | PTU | EN | M0)) /*GPMC_D1*/\
+ MUX_VAL(CP(GPMC_D2), (IEN | PTU | EN | M0)) /*GPMC_D2*/\
+ MUX_VAL(CP(GPMC_D3), (IEN | PTU | EN | M0)) /*GPMC_D3*/\
+ MUX_VAL(CP(GPMC_D4), (IEN | PTU | EN | M0)) /*GPMC_D4*/\
+ MUX_VAL(CP(GPMC_D5), (IEN | PTU | EN | M0)) /*GPMC_D5*/\
+ MUX_VAL(CP(GPMC_D6), (IEN | PTU | EN | M0)) /*GPMC_D6*/\
+ MUX_VAL(CP(GPMC_D7), (IEN | PTU | EN | M0)) /*GPMC_D7*/\
+ MUX_VAL(CP(GPMC_D8), (IEN | PTU | EN | M0)) /*GPMC_D8*/\
+ MUX_VAL(CP(GPMC_D9), (IEN | PTU | EN | M0)) /*GPMC_D9*/\
+ MUX_VAL(CP(GPMC_D10), (IEN | PTU | EN | M0)) /*GPMC_D10*/\
+ MUX_VAL(CP(GPMC_D11), (IEN | PTU | EN | M0)) /*GPMC_D11*/\
+ MUX_VAL(CP(GPMC_D12), (IEN | PTU | EN | M0)) /*GPMC_D12*/\
+ MUX_VAL(CP(GPMC_D13), (IEN | PTU | EN | M0)) /*GPMC_D13*/\
+ MUX_VAL(CP(GPMC_D14), (IEN | PTU | EN | M0)) /*GPMC_D14*/\
+ MUX_VAL(CP(GPMC_D15), (IEN | PTU | EN | M0)) /*GPMC_D15*/\
+ MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) /*GPMC_nCS0*/\
+ MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M0)) /*GPMC_nCS1*/\
+ MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M0)) /*GPMC_nCS2*/\
+ MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M0)) /*GPMC_nCS3*/\
+ MUX_VAL(CP(GPMC_NCS4), (IEN | PTU | EN | M0)) /*GPMC_nCS4*/\
+ MUX_VAL(CP(GPMC_NCS5), (IDIS | PTU | EN | M0)) /*GPMC_nCS5*/\
+ MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M0)) /*GPMC_nCS6*/\
+ MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M0)) /*GPMC_nCS7*/\
+ MUX_VAL(CP(GPMC_CLK), (IDIS | PTU | EN | M0)) /*GPMC_CLK*/\
+ MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /*GPMC_nADV_ALE*/\
+ MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /*GPMC_nOE*/\
+ MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /*GPMC_nWE*/\
+ MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTU | EN | M0)) /*GPMC_nBE0_CLE*/\
+ MUX_VAL(CP(GPMC_NBE1), (IEN | PTU | EN | M0)) /*GPMC_nBE1*/\
+ MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0)) /*GPMC_nWP*/\
+ MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) /*GPMC_WAIT0*/\
+ MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) /*GPMC_WAIT1*/\
+ MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M4)) /*GPIO_64*/\
+ /* - ETH_nRESET*/\
+ MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0)) /*GPMC_WAIT3*/\
+ /*DSS*/\
+ MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
+ MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0)) /*DSS_HSYNC*/\
+ MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0)) /*DSS_VSYNC*/\
+ MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0)) /*DSS_ACBIAS*/\
+ MUX_VAL(CP(DSS_DATA0), (IDIS | PTD | DIS | M0)) /*DSS_DATA0*/\
+ MUX_VAL(CP(DSS_DATA1), (IDIS | PTD | DIS | M0)) /*DSS_DATA1*/\
+ MUX_VAL(CP(DSS_DATA2), (IDIS | PTD | DIS | M0)) /*DSS_DATA2*/\
+ MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M0)) /*DSS_DATA3*/\
+ MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M0)) /*DSS_DATA4*/\
+ MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M0)) /*DSS_DATA5*/\
+ MUX_VAL(CP(DSS_DATA6), (IDIS | PTD | DIS | M0)) /*DSS_DATA6*/\
+ MUX_VAL(CP(DSS_DATA7), (IDIS | PTD | DIS | M0)) /*DSS_DATA7*/\
+ MUX_VAL(CP(DSS_DATA8), (IDIS | PTD | DIS | M0)) /*DSS_DATA8*/\
+ MUX_VAL(CP(DSS_DATA9), (IDIS | PTD | DIS | M0)) /*DSS_DATA9*/\
+ MUX_VAL(CP(DSS_DATA10), (IDIS | PTD | DIS | M0)) /*DSS_DATA10*/\
+ MUX_VAL(CP(DSS_DATA11), (IDIS | PTD | DIS | M0)) /*DSS_DATA11*/\
+ MUX_VAL(CP(DSS_DATA12), (IDIS | PTD | DIS | M0)) /*DSS_DATA12*/\
+ MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | DIS | M0)) /*DSS_DATA13*/\
+ MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | DIS | M0)) /*DSS_DATA14*/\
+ MUX_VAL(CP(DSS_DATA15), (IDIS | PTD | DIS | M0)) /*DSS_DATA15*/\
+ MUX_VAL(CP(DSS_DATA16), (IDIS | PTD | DIS | M0)) /*DSS_DATA16*/\
+ MUX_VAL(CP(DSS_DATA17), (IDIS | PTD | DIS | M0)) /*DSS_DATA17*/\
+ MUX_VAL(CP(DSS_DATA18), (IDIS | PTD | DIS | M0)) /*DSS_DATA18*/\
+ MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M0)) /*DSS_DATA19*/\
+ MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M0)) /*DSS_DATA20*/\
+ MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M0)) /*DSS_DATA21*/\
+ MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0)) /*DSS_DATA22*/\
+ MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0)) /*DSS_DATA23*/\
+ /*CAMERA*/\
+ MUX_VAL(CP(CAM_HS), (IEN | PTU | EN | M0)) /*CAM_HS */\
+ MUX_VAL(CP(CAM_VS), (IEN | PTU | EN | M0)) /*CAM_VS */\
+ MUX_VAL(CP(CAM_XCLKA), (IDIS | PTD | DIS | M0)) /*CAM_XCLKA*/\
+ MUX_VAL(CP(CAM_PCLK), (IEN | PTU | EN | M0)) /*CAM_PCLK*/\
+ MUX_VAL(CP(CAM_FLD), (IDIS | PTD | DIS | M4)) /*GPIO_98*/\
+ /* - CAM_RESET*/\
+ MUX_VAL(CP(CAM_D0), (IEN | PTD | DIS | M0)) /*CAM_D0*/\
+ MUX_VAL(CP(CAM_D1), (IEN | PTD | DIS | M0)) /*CAM_D1*/\
+ MUX_VAL(CP(CAM_D2), (IEN | PTD | DIS | M0)) /*CAM_D2*/\
+ MUX_VAL(CP(CAM_D3), (IEN | PTD | DIS | M0)) /*CAM_D3*/\
+ MUX_VAL(CP(CAM_D4), (IEN | PTD | DIS | M0)) /*CAM_D4*/\
+ MUX_VAL(CP(CAM_D5), (IEN | PTD | DIS | M0)) /*CAM_D5*/\
+ MUX_VAL(CP(CAM_D6), (IEN | PTD | DIS | M0)) /*CAM_D6*/\
+ MUX_VAL(CP(CAM_D7), (IEN | PTD | DIS | M0)) /*CAM_D7*/\
+ MUX_VAL(CP(CAM_D8), (IEN | PTD | DIS | M0)) /*CAM_D8*/\
+ MUX_VAL(CP(CAM_D9), (IEN | PTD | DIS | M0)) /*CAM_D9*/\
+ MUX_VAL(CP(CAM_D10), (IEN | PTD | DIS | M0)) /*CAM_D10*/\
+ MUX_VAL(CP(CAM_D11), (IEN | PTD | DIS | M0)) /*CAM_D11*/\
+ MUX_VAL(CP(CAM_XCLKB), (IDIS | PTD | DIS | M0)) /*CAM_XCLKB*/\
+ MUX_VAL(CP(CAM_WEN), (IEN | PTD | DIS | M4)) /*GPIO_167*/\
+ MUX_VAL(CP(CAM_STROBE), (IDIS | PTD | DIS | M0)) /*CAM_STROBE*/\
+ MUX_VAL(CP(CSI2_DX0), (IEN | PTD | DIS | M0)) /*CSI2_DX0*/\
+ MUX_VAL(CP(CSI2_DY0), (IEN | PTD | DIS | M0)) /*CSI2_DY0*/\
+ MUX_VAL(CP(CSI2_DX1), (IEN | PTD | DIS | M0)) /*CSI2_DX1*/\
+ MUX_VAL(CP(CSI2_DY1), (IEN | PTD | DIS | M0)) /*CSI2_DY1*/\
+ /*Audio Interface */\
+ MUX_VAL(CP(MCBSP2_FSX), (IEN | PTD | DIS | M0)) /*McBSP2_FSX*/\
+ MUX_VAL(CP(MCBSP2_CLKX), (IEN | PTD | DIS | M0)) /*McBSP2_CLKX*/\
+ MUX_VAL(CP(MCBSP2_DR), (IEN | PTD | DIS | M0)) /*McBSP2_DR*/\
+ MUX_VAL(CP(MCBSP2_DX), (IDIS | PTD | DIS | M0)) /*McBSP2_DX*/\
+ /*Expansion card */\
+ MUX_VAL(CP(MMC1_CLK), (IDIS | PTU | EN | M0)) /*MMC1_CLK*/\
+ MUX_VAL(CP(MMC1_CMD), (IEN | PTU | EN | M0)) /*MMC1_CMD*/\
+ MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | EN | M0)) /*MMC1_DAT0*/\
+ MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | EN | M0)) /*MMC1_DAT1*/\
+ MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | EN | M0)) /*MMC1_DAT2*/\
+ MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | EN | M0)) /*MMC1_DAT3*/\
+ MUX_VAL(CP(MMC1_DAT4), (IEN | PTU | EN | M0)) /*MMC1_DAT4*/\
+ MUX_VAL(CP(MMC1_DAT5), (IEN | PTU | EN | M0)) /*MMC1_DAT5*/\
+ MUX_VAL(CP(MMC1_DAT6), (IEN | PTU | EN | M0)) /*MMC1_DAT6*/\
+ MUX_VAL(CP(MMC1_DAT7), (IEN | PTU | EN | M0)) /*MMC1_DAT7*/\
+ /*Wireless LAN */\
+ MUX_VAL(CP(MMC2_CLK), (IEN | PTD | DIS | M0)) /*MMC2_CLK*/\
+ MUX_VAL(CP(MMC2_CMD), (IEN | PTU | EN | M0)) /*MMC2_CMD*/\
+ MUX_VAL(CP(MMC2_DAT0), (IEN | PTU | EN | M0)) /*MMC2_DAT0*/\
+ MUX_VAL(CP(MMC2_DAT1), (IEN | PTU | EN | M0)) /*MMC2_DAT1*/\
+ MUX_VAL(CP(MMC2_DAT2), (IEN | PTU | EN | M0)) /*MMC2_DAT2*/\
+ MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | EN | M0)) /*MMC2_DAT3*/\
+ MUX_VAL(CP(MMC2_DAT4), (IDIS | PTD | DIS | M0)) /*MMC2_DAT4*/\
+ MUX_VAL(CP(MMC2_DAT5), (IDIS | PTD | DIS | M0)) /*MMC2_DAT5*/\
+ MUX_VAL(CP(MMC2_DAT6), (IDIS | PTD | DIS | M0)) /*MMC2_DAT6 */\
+ MUX_VAL(CP(MMC2_DAT7), (IEN | PTU | EN | M0)) /*MMC2_DAT7*/\
+ /*Bluetooth*/\
+ MUX_VAL(CP(MCBSP3_DX), (IDIS | PTD | DIS | M0)) /*McBSP3_DX*/\
+ MUX_VAL(CP(MCBSP3_DR), (IEN | PTD | DIS | M0)) /*McBSP3_DR*/\
+ MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTD | DIS | M0)) /*McBSP3_CLKX */\
+ MUX_VAL(CP(MCBSP3_FSX), (IEN | PTD | DIS | M0)) /*McBSP3_FSX*/\
+ MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M0)) /*UART2_CTS*/\
+ MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M0)) /*UART2_RTS*/\
+ MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M0)) /*UART2_TX*/\
+ MUX_VAL(CP(UART2_RX), (IEN | PTD | DIS | M0)) /*UART2_RX*/\
+ /*Modem Interface */\
+ MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0)) /*UART1_TX*/\
+ MUX_VAL(CP(UART1_RTS), (IDIS | PTD | DIS | M0)) /*UART1_RTS*/\
+ MUX_VAL(CP(UART1_CTS), (IEN | PTU | DIS | M0)) /*UART1_CTS*/\
+ MUX_VAL(CP(UART1_RX), (IEN | PTD | DIS | M0)) /*UART1_RX*/\
+ MUX_VAL(CP(MCBSP4_CLKX), (IDIS | PTD | DIS | M4)) /*GPIO_152*/\
+ /* - LCD_INI*/\
+ MUX_VAL(CP(MCBSP4_DR), (IDIS | PTD | DIS | M4)) /*GPIO_153*/\
+ /* - LCD_ENVDD */\
+ MUX_VAL(CP(MCBSP4_DX), (IDIS | PTD | DIS | M4)) /*GPIO_154*/\
+ /* - LCD_QVGA/nVGA */\
+ MUX_VAL(CP(MCBSP4_FSX), (IDIS | PTD | DIS | M4)) /*GPIO_155*/\
+ /* - LCD_RESB */\
+ MUX_VAL(CP(MCBSP1_CLKR), (IEN | PTD | DIS | M0)) /*MCBSP1_CLKR */\
+ MUX_VAL(CP(MCBSP1_FSR), (IDIS | PTU | EN | M0)) /*MCBSP1_FSR*/\
+ MUX_VAL(CP(MCBSP1_DX), (IDIS | PTD | DIS | M0)) /*MCBSP1_DX*/\
+ MUX_VAL(CP(MCBSP1_DR), (IEN | PTD | DIS | M0)) /*MCBSP1_DR*/\
+ MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0)) /*MCBSP_CLKS */\
+ MUX_VAL(CP(MCBSP1_FSX), (IEN | PTD | DIS | M0)) /*MCBSP1_FSX*/\
+ MUX_VAL(CP(MCBSP1_CLKX), (IEN | PTD | DIS | M0)) /*MCBSP1_CLKX */\
+ /*Serial Interface*/\
+ MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTD | EN | M0)) /*UART3_CTS_*/\
+ /* RCTX*/\
+ MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTD | DIS | M0)) /*UART3_RTS_SD */\
+ MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0)) /*UART3_RX_IRRX*/\
+ MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0)) /*UART3_TX_IRTX*/\
+ MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0)) /*HSUSB0_CLK*/\
+ MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0)) /*HSUSB0_STP*/\
+ MUX_VAL(CP(HSUSB0_DIR), (IEN | PTD | DIS | M0)) /*HSUSB0_DIR*/\
+ MUX_VAL(CP(HSUSB0_NXT), (IEN | PTD | DIS | M0)) /*HSUSB0_NXT*/\
+ MUX_VAL(CP(HSUSB0_DATA0), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA0*/\
+ MUX_VAL(CP(HSUSB0_DATA1), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA1*/\
+ MUX_VAL(CP(HSUSB0_DATA2), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA2*/\
+ MUX_VAL(CP(HSUSB0_DATA3), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA3*/\
+ MUX_VAL(CP(HSUSB0_DATA4), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA4*/\
+ MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA5*/\
+ MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA6*/\
+ MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA7*/\
+ MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)) /*I2C1_SCL*/\
+ MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)) /*I2C1_SDA*/\
+ MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M0)) /*I2C2_SCL*/\
+ MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M0)) /*I2C2_SDA*/\
+ MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0)) /*I2C3_SCL*/\
+ MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0)) /*I2C3_SDA*/\
+ MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0)) /*I2C4_SCL*/\
+ MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0)) /*I2C4_SDA*/\
+ MUX_VAL(CP(HDQ_SIO), (IEN | PTU | EN | M0)) /*HDQ_SIO*/\
+ MUX_VAL(CP(MCSPI1_CLK), (IEN | PTD | DIS | M0)) /*McSPI1_CLK*/\
+ MUX_VAL(CP(MCSPI1_SIMO), (IEN | PTD | DIS | M0)) /*McSPI1_SIMO */\
+ MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | DIS | M0)) /*McSPI1_SOMI */\
+ MUX_VAL(CP(MCSPI1_CS0), (IEN | PTD | EN | M0)) /*McSPI1_CS0*/\
+ MUX_VAL(CP(MCSPI1_CS1), (IEN | PTD | EN | M4)) /*GPIO_175*/\
+ /* TS_PEN_IRQ */\
+ MUX_VAL(CP(MCSPI1_CS2), (IEN | PTU | DIS | M4)) /*GPIO_176*/\
+ /* - LAN_INTR*/\
+ MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | EN | M0)) /*McSPI1_CS3*/\
+ MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | DIS | M0)) /*McSPI2_CLK*/\
+ MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | DIS | M0)) /*McSPI2_SIMO*/\
+ MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | DIS | M0)) /*McSPI2_SOMI*/\
+ MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | EN | M0)) /*McSPI2_CS0*/\
+ MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | EN | M0)) /*McSPI2_CS1*/\
+ /*Control and debug */\
+ MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0)) /*SYS_32K*/\
+ MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) /*SYS_CLKREQ*/\
+ MUX_VAL(CP(SYS_NIRQ), (IEN | PTU | EN | M0)) /*SYS_nIRQ*/\
+ MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4)) /*GPIO_2*/\
+ /* - PEN_IRQ */\
+ MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4)) /*GPIO_3 */\
+ MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /*GPIO_4*/\
+ MUX_VAL(CP(SYS_BOOT3), (IEN | PTD | DIS | M4)) /*GPIO_5*/\
+ MUX_VAL(CP(SYS_BOOT4), (IEN | PTD | DIS | M4)) /*GPIO_6*/\
+ MUX_VAL(CP(SYS_BOOT5), (IEN | PTD | DIS | M4)) /*GPIO_7*/\
+ MUX_VAL(CP(SYS_BOOT6), (IDIS | PTD | DIS | M4)) /*GPIO_8*/\
+ /* - VIO_1V8*/\
+ MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0)) /*SYS_OFF_MODE*/\
+ MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M0)) /*SYS_CLKOUT1*/\
+ MUX_VAL(CP(SYS_CLKOUT2), (IEN | PTU | EN | M0)) /*SYS_CLKOUT2*/\
+ MUX_VAL(CP(JTAG_nTRST), (IEN | PTD | DIS | M0)) /*JTAG_nTRST*/\
+ MUX_VAL(CP(JTAG_TCK), (IEN | PTD | DIS | M0)) /*JTAG_TCK*/\
+ MUX_VAL(CP(JTAG_TMS), (IEN | PTD | DIS | M0)) /*JTAG_TMS*/\
+ MUX_VAL(CP(JTAG_TDI), (IEN | PTD | DIS | M0)) /*JTAG_TDI*/\
+ MUX_VAL(CP(JTAG_EMU0), (IEN | PTD | DIS | M0)) /*JTAG_EMU0*/\
+ MUX_VAL(CP(JTAG_EMU1), (IEN | PTD | DIS | M0)) /*JTAG_EMU1*/\
+ MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | EN | M0)) /*ETK_CLK*/\
+ MUX_VAL(CP(ETK_CTL_ES2), (IDIS | PTD | DIS | M0)) /*ETK_CTL*/\
+ MUX_VAL(CP(ETK_D0_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D0*/\
+ MUX_VAL(CP(ETK_D1_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D1*/\
+ MUX_VAL(CP(ETK_D2_ES2 ), (IEN | PTD | EN | M0)) /*ETK_D2*/\
+ MUX_VAL(CP(ETK_D3_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D3*/\
+ MUX_VAL(CP(ETK_D4_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D4*/\
+ MUX_VAL(CP(ETK_D5_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D5*/\
+ MUX_VAL(CP(ETK_D6_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D6*/\
+ MUX_VAL(CP(ETK_D7_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D7*/\
+ MUX_VAL(CP(ETK_D8_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D8*/\
+ MUX_VAL(CP(ETK_D9_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D9*/\
+ MUX_VAL(CP(ETK_D10_ES2), (IEN | PTD | DIS | M0)) /*ETK_D10*/\
+ MUX_VAL(CP(ETK_D11_ES2), (IEN | PTD | DIS | M0)) /*ETK_D11*/\
+ MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | DIS | M0)) /*ETK_D12*/\
+ MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | DIS | M0)) /*ETK_D13*/\
+ MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M0)) /*ETK_D14*/\
+ MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | DIS | M0)) /*ETK_D15*/\
+ /*Die to Die */\
+ MUX_VAL(CP(D2D_MCAD1), (IEN | PTD | EN | M0)) /*d2d_mcad1*/\
+ MUX_VAL(CP(D2D_MCAD2), (IEN | PTD | EN | M0)) /*d2d_mcad2*/\
+ MUX_VAL(CP(D2D_MCAD3), (IEN | PTD | EN | M0)) /*d2d_mcad3*/\
+ MUX_VAL(CP(D2D_MCAD4), (IEN | PTD | EN | M0)) /*d2d_mcad4*/\
+ MUX_VAL(CP(D2D_MCAD5), (IEN | PTD | EN | M0)) /*d2d_mcad5*/\
+ MUX_VAL(CP(D2D_MCAD6), (IEN | PTD | EN | M0)) /*d2d_mcad6*/\
+ MUX_VAL(CP(D2D_MCAD7), (IEN | PTD | EN | M0)) /*d2d_mcad7*/\
+ MUX_VAL(CP(D2D_MCAD8), (IEN | PTD | EN | M0)) /*d2d_mcad8*/\
+ MUX_VAL(CP(D2D_MCAD9), (IEN | PTD | EN | M0)) /*d2d_mcad9*/\
+ MUX_VAL(CP(D2D_MCAD10), (IEN | PTD | EN | M0)) /*d2d_mcad10*/\
+ MUX_VAL(CP(D2D_MCAD11), (IEN | PTD | EN | M0)) /*d2d_mcad11*/\
+ MUX_VAL(CP(D2D_MCAD12), (IEN | PTD | EN | M0)) /*d2d_mcad12*/\
+ MUX_VAL(CP(D2D_MCAD13), (IEN | PTD | EN | M0)) /*d2d_mcad13*/\
+ MUX_VAL(CP(D2D_MCAD14), (IEN | PTD | EN | M0)) /*d2d_mcad14*/\
+ MUX_VAL(CP(D2D_MCAD15), (IEN | PTD | EN | M0)) /*d2d_mcad15*/\
+ MUX_VAL(CP(D2D_MCAD16), (IEN | PTD | EN | M0)) /*d2d_mcad16*/\
+ MUX_VAL(CP(D2D_MCAD17), (IEN | PTD | EN | M0)) /*d2d_mcad17*/\
+ MUX_VAL(CP(D2D_MCAD18), (IEN | PTD | EN | M0)) /*d2d_mcad18*/\
+ MUX_VAL(CP(D2D_MCAD19), (IEN | PTD | EN | M0)) /*d2d_mcad19*/\
+ MUX_VAL(CP(D2D_MCAD20), (IEN | PTD | EN | M0)) /*d2d_mcad20*/\
+ MUX_VAL(CP(D2D_MCAD21), (IEN | PTD | EN | M0)) /*d2d_mcad21*/\
+ MUX_VAL(CP(D2D_MCAD22), (IEN | PTD | EN | M0)) /*d2d_mcad22*/\
+ MUX_VAL(CP(D2D_MCAD23), (IEN | PTD | EN | M0)) /*d2d_mcad23*/\
+ MUX_VAL(CP(D2D_MCAD24), (IEN | PTD | EN | M0)) /*d2d_mcad24*/\
+ MUX_VAL(CP(D2D_MCAD25), (IEN | PTD | EN | M0)) /*d2d_mcad25*/\
+ MUX_VAL(CP(D2D_MCAD26), (IEN | PTD | EN | M0)) /*d2d_mcad26*/\
+ MUX_VAL(CP(D2D_MCAD27), (IEN | PTD | EN | M0)) /*d2d_mcad27*/\
+ MUX_VAL(CP(D2D_MCAD28), (IEN | PTD | EN | M0)) /*d2d_mcad28*/\
+ MUX_VAL(CP(D2D_MCAD29), (IEN | PTD | EN | M0)) /*d2d_mcad29*/\
+ MUX_VAL(CP(D2D_MCAD30), (IEN | PTD | EN | M0)) /*d2d_mcad30*/\
+ MUX_VAL(CP(D2D_MCAD31), (IEN | PTD | EN | M0)) /*d2d_mcad31*/\
+ MUX_VAL(CP(D2D_MCAD32), (IEN | PTD | EN | M0)) /*d2d_mcad32*/\
+ MUX_VAL(CP(D2D_MCAD33), (IEN | PTD | EN | M0)) /*d2d_mcad33*/\
+ MUX_VAL(CP(D2D_MCAD34), (IEN | PTD | EN | M0)) /*d2d_mcad34*/\
+ MUX_VAL(CP(D2D_MCAD35), (IEN | PTD | EN | M0)) /*d2d_mcad35*/\
+ MUX_VAL(CP(D2D_MCAD36), (IEN | PTD | EN | M0)) /*d2d_mcad36*/\
+ MUX_VAL(CP(D2D_CLK26MI), (IEN | PTD | DIS | M0)) /*d2d_clk26mi*/\
+ MUX_VAL(CP(D2D_NRESPWRON), (IEN | PTD | EN | M0)) /*d2d_nrespwron*/\
+ MUX_VAL(CP(D2D_NRESWARM), (IEN | PTU | EN | M0)) /*d2d_nreswarm */\
+ MUX_VAL(CP(D2D_ARM9NIRQ), (IEN | PTD | DIS | M0)) /*d2d_arm9nirq */\
+ MUX_VAL(CP(D2D_UMA2P6FIQ), (IEN | PTD | DIS | M0)) /*d2d_uma2p6fiq*/\
+ MUX_VAL(CP(D2D_SPINT), (IEN | PTD | EN | M0)) /*d2d_spint*/\
+ MUX_VAL(CP(D2D_FRINT), (IEN | PTD | EN | M0)) /*d2d_frint*/\
+ MUX_VAL(CP(D2D_DMAREQ0), (IEN | PTD | DIS | M0)) /*d2d_dmareq0*/\
+ MUX_VAL(CP(D2D_DMAREQ1), (IEN | PTD | DIS | M0)) /*d2d_dmareq1*/\
+ MUX_VAL(CP(D2D_DMAREQ2), (IEN | PTD | DIS | M0)) /*d2d_dmareq2*/\
+ MUX_VAL(CP(D2D_DMAREQ3), (IEN | PTD | DIS | M0)) /*d2d_dmareq3*/\
+ MUX_VAL(CP(D2D_N3GTRST), (IEN | PTD | DIS | M0)) /*d2d_n3gtrst*/\
+ MUX_VAL(CP(D2D_N3GTDI), (IEN | PTD | DIS | M0)) /*d2d_n3gtdi*/\
+ MUX_VAL(CP(D2D_N3GTDO), (IEN | PTD | DIS | M0)) /*d2d_n3gtdo*/\
+ MUX_VAL(CP(D2D_N3GTMS), (IEN | PTD | DIS | M0)) /*d2d_n3gtms*/\
+ MUX_VAL(CP(D2D_N3GTCK), (IEN | PTD | DIS | M0)) /*d2d_n3gtck*/\
+ MUX_VAL(CP(D2D_N3GRTCK), (IEN | PTD | DIS | M0)) /*d2d_n3grtck*/\
+ MUX_VAL(CP(D2D_MSTDBY), (IEN | PTU | EN | M0)) /*d2d_mstdby*/\
+ MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0)) /*d2d_swakeup*/\
+ MUX_VAL(CP(D2D_IDLEREQ), (IEN | PTD | DIS | M0)) /*d2d_idlereq*/\
+ MUX_VAL(CP(D2D_IDLEACK), (IEN | PTU | EN | M0)) /*d2d_idleack*/\
+ MUX_VAL(CP(D2D_MWRITE), (IEN | PTD | DIS | M0)) /*d2d_mwrite*/\
+ MUX_VAL(CP(D2D_SWRITE), (IEN | PTD | DIS | M0)) /*d2d_swrite*/\
+ MUX_VAL(CP(D2D_MREAD), (IEN | PTD | DIS | M0)) /*d2d_mread*/\
+ MUX_VAL(CP(D2D_SREAD), (IEN | PTD | DIS | M0)) /*d2d_sread*/\
+ MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_mbusflag*/\
+ MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_sbusflag*/\
+ MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0)) /*sdrc_cke0*/\
+ MUX_VAL(CP(SDRC_CKE1), (IDIS | PTD | DIS | M7)) /*sdrc_cke1*/\
+
+#endif
--- /dev/null
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := omap1510innovator.o
+SOBJS := lowlevel_init.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+#
+# (C) Copyright 2002
+# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
+# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+#
+# (C) Copyright 2003
+# Texas Instruments, <www.ti.com>
+# Kshitij Gupta <Kshitij@ti.com>
+#
+# TI Innovator board with OMAP1510 (ARM925T) cpu
+# see http://www.ti.com/ for more information on Texas Insturments
+#
+# Innovator has 1 bank of 256 MB SDRAM
+# Physical Address:
+# 1000'0000 to 2000'0000
+#
+#
+# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000 (mem base + reserved)
+#
+# we load ourself to 1108'0000
+#
+#
+
+
+TEXT_BASE = 0x11080000
--- /dev/null
+/*
+ * Board specific setup info
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ *
+ * -- Some bits of code used from rrload's head_OMAP1510.s --
+ * Copyright (C) 2002 RidgeRun, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+
+#if defined(CONFIG_OMAP1510)
+#include <./configs/omap1510.h>
+#endif
+
+#define OMAP1510_CLKS ((1<<EN_XORPCK)|(1<<EN_PERCK)|(1<<EN_TIMCK)|(1<<EN_GPIOCK))
+
+
+_TEXT_BASE:
+ .word TEXT_BASE /* sdram load addr from config.mk */
+
+.globl lowlevel_init
+lowlevel_init:
+
+ /*
+ * Configure 1510 pins functions to match our board.
+ */
+ ldr r0, REG_PULL_DWN_CTRL_0
+ ldr r1, VAL_PULL_DWN_CTRL_0
+ str r1, [r0]
+ ldr r0, REG_PULL_DWN_CTRL_1
+ ldr r1, VAL_PULL_DWN_CTRL_1
+ str r1, [r0]
+ ldr r0, REG_PULL_DWN_CTRL_2
+ ldr r1, VAL_PULL_DWN_CTRL_2
+ str r1, [r0]
+ ldr r0, REG_PULL_DWN_CTRL_3
+ ldr r1, VAL_PULL_DWN_CTRL_3
+ str r1, [r0]
+ ldr r0, REG_FUNC_MUX_CTRL_4
+ ldr r1, VAL_FUNC_MUX_CTRL_4
+ str r1, [r0]
+ ldr r0, REG_FUNC_MUX_CTRL_5
+ ldr r1, VAL_FUNC_MUX_CTRL_5
+ str r1, [r0]
+ ldr r0, REG_FUNC_MUX_CTRL_6
+ ldr r1, VAL_FUNC_MUX_CTRL_6
+ str r1, [r0]
+ ldr r0, REG_FUNC_MUX_CTRL_7
+ ldr r1, VAL_FUNC_MUX_CTRL_7
+ str r1, [r0]
+ ldr r0, REG_FUNC_MUX_CTRL_8
+ ldr r1, VAL_FUNC_MUX_CTRL_8
+ str r1, [r0]
+ ldr r0, REG_FUNC_MUX_CTRL_9
+ ldr r1, VAL_FUNC_MUX_CTRL_9
+ str r1, [r0]
+ ldr r0, REG_FUNC_MUX_CTRL_A
+ ldr r1, VAL_FUNC_MUX_CTRL_A
+ str r1, [r0]
+ ldr r0, REG_FUNC_MUX_CTRL_B
+ ldr r1, VAL_FUNC_MUX_CTRL_B
+ str r1, [r0]
+ ldr r0, REG_FUNC_MUX_CTRL_C
+ ldr r1, VAL_FUNC_MUX_CTRL_C
+ str r1, [r0]
+ ldr r0, REG_FUNC_MUX_CTRL_D
+ ldr r1, VAL_FUNC_MUX_CTRL_D
+ str r1, [r0]
+ ldr r0, REG_VOLTAGE_CTRL_0
+ ldr r1, VAL_VOLTAGE_CTRL_0
+ str r1, [r0]
+ ldr r0, REG_TEST_DBG_CTRL_0
+ ldr r1, VAL_TEST_DBG_CTRL_0
+ str r1, [r0]
+ ldr r0, REG_MOD_CONF_CTRL_0
+ ldr r1, VAL_MOD_CONF_CTRL_0
+ str r1, [r0]
+
+ /* Move to 1510 mode */
+ ldr r0, REG_COMP_MODE_CTRL_0
+ ldr r1, VAL_COMP_MODE_CTRL_0
+ str r1, [r0]
+
+ /* Set up Traffic Ctlr*/
+ ldr r0, REG_TC_IMIF_PRIO
+ mov r1, #0x0
+ str r1, [r0]
+ ldr r0, REG_TC_EMIFS_PRIO
+ str r1, [r0]
+ ldr r0, REG_TC_EMIFF_PRIO
+ str r1, [r0]
+
+ ldr r0, REG_TC_EMIFS_CONFIG
+ ldr r1, [r0]
+ bic r1, r1, #0x08 /* clear the global power-down enable PDE bit */
+ bic r1, r1, #0x01 /* write protect flash by clearing the WP bit */
+ str r1, [r0] /* EMIFS GlB Configuration. (value 0x12 most likely) */
+
+ /* Setup some clock domains */
+ ldr r1, =OMAP1510_CLKS
+ ldr r0, REG_ARM_IDLECT2
+ strh r1, [r0] /* CLKM, Clock domain control. */
+
+ mov r1, #0x01 /* PER_EN bit */
+ ldr r0, REG_ARM_RSTCT2
+ strh r1, [r0] /* CLKM; Peripheral reset. */
+
+ /* Set CLKM to Sync-Scalable */
+ /* I supposidly need to enable the dsp clock before switching */
+ mov r1, #0x1000
+ ldr r0, REG_ARM_SYSST
+ strh r1, [r0]
+ mov r0, #0x400
+1:
+ subs r0, r0, #0x1 /* wait for any bubbles to finish */
+ bne 1b
+
+ ldr r1, VAL_ARM_CKCTL /* use 12Mhz ref, PER must be <= 50Mhz so /2 */
+ ldr r0, REG_ARM_CKCTL
+ strh r1, [r0]
+
+ /* setup DPLL 1 */
+ ldr r1, VAL_DPLL1_CTL
+ ldr r0, REG_DPLL1_CTL
+ strh r1, [r0]
+ ands r1, r1, #0x10 /* Check if PLL is enabled. */
+ beq lock_end /* Do not look for lock if BYPASS selected */
+2:
+ ldrh r1, [r0]
+ ands r1, r1, #0x01 /* Check the LOCK bit. */
+ beq 2b /* ...loop until bit goes hi. */
+lock_end:
+
+ /* Set memory timings corresponding to the new clock speed */
+
+ /* Check execution location to determine current execution location
+ * and branch to appropriate initialization code.
+ */
+ mov r0, #0x10000000 /* Load physical SDRAM base. */
+ mov r1, pc /* Get current execution location. */
+ /* Zero all but top 6 bits of PC, as they alone detect whether an
+ * address is in the range 0x1000:0000-0x13ff:ffff, the 64M sized
+ * valid range for SDRAM on the OMAP 1510/5910.
+ */
+ and r1, r1, #0xfc000000
+ cmp r1, r0 /* Compare. */
+ beq skip_sdram /* Skip over EMIF-fast initialization
+ * if running from SDRAM.
+ */
+
+ /*
+ * Delay for SDRAM initialization.
+ */
+ mov r3, #0x1800 /* value should be checked */
+3:
+ subs r3, r3, #0x1 /* Decrement count */
+ bne 3b
+
+ /*
+ * Set SDRAM control values. Disable refresh before MRS command.
+ */
+ ldr r0, VAL_TC_EMIFF_SDRAM_CONFIG /* get good value */
+ bic r3, r0, #0xC /* (BIT3|BIT2) ulConfig with auto-refresh disabled. */
+ orr r3, r3, #0x8000000 /* (BIT27) Disable CLK when Power down or Self-Refresh */
+ orr r3, r3, #0x4000000 /* BIT26 Power Down Enable */
+ ldr r2, REG_TC_EMIFF_SDRAM_CONFIG /* Point to configuration register. */
+ str r3, [r2] /* Store the passed value with AR disabled. */
+
+ ldr r1, VAL_TC_EMIFF_MRS /* get MRS value */
+ ldr r2, REG_TC_EMIFF_MRS /* Point to MRS register. */
+ str r1, [r2] /* Store the passed value.*/
+
+ ldr r2, REG_TC_EMIFF_SDRAM_CONFIG /* Point to configuration register. */
+ str r0, [r2] /* Store the passed value. */
+
+ /*
+ * Delay for SDRAM initialization.
+ */
+ mov r3, #0x1800
+4:
+ subs r3, r3, #1 /* Decrement count. */
+ bne 4b
+
+skip_sdram:
+
+ /* slow interface */
+ ldr r1, VAL_TC_EMIFS_CS0_CONFIG
+ ldr r0, REG_TC_EMIFS_CS0_CONFIG
+ str r1, [r0] /* Chip Select 0 */
+ ldr r1, VAL_TC_EMIFS_CS1_CONFIG
+ ldr r0, REG_TC_EMIFS_CS1_CONFIG
+ str r1, [r0] /* Chip Select 1 */
+ ldr r1, VAL_TC_EMIFS_CS2_CONFIG
+ ldr r0, REG_TC_EMIFS_CS2_CONFIG
+ str r1, [r0] /* Chip Select 2 */
+ ldr r1, VAL_TC_EMIFS_CS3_CONFIG
+ ldr r0, REG_TC_EMIFS_CS3_CONFIG
+ str r1, [r0] /* Chip Select 3 */
+
+ /* Next, Enable the RS232 Line Drivers in the FPGA. */
+ /* Also, power on the audio CODEC's amplifier here, */
+ /* which will make a noise on the audio output. */
+ /* This is done here instead of in the kernel so there */
+ /* isn't a loud popping noise at the start of each */
+ /* song. */
+ /* Also, disable the CODEC's clocks. */
+ /* omap1510-HelenP1 [specific] */
+
+ ldr r0, REG_FPGA_POWER
+ mov r1, #0
+ ldr r2, REG_FPGA_DIP_SWITCH
+ ldrb r3, [r2]
+ cmp r3, #0x8
+ movne r1, #0x62 /* Enable the RS232 Line Drivers in the EPLD */
+ strb r1, [r0]
+ ldr r0, REG_FPGA_AUDIO
+ mov r1, #0x0 /* Disable sound driver (CODEC clocks) */
+ strb r1, [r0]
+
+ /* back to arch calling code */
+ mov pc, lr
+
+/* the literal pools origin */
+ .ltorg
+
+/* OMAP configuration registers */
+REG_FUNC_MUX_CTRL_0: /* 32 bits */
+ .word 0xfffe1000
+REG_FUNC_MUX_CTRL_1: /* 32 bits */
+ .word 0xfffe1004
+REG_FUNC_MUX_CTRL_2: /* 32 bits */
+ .word 0xfffe1008
+REG_COMP_MODE_CTRL_0: /* 32 bits */
+ .word 0xfffe100c
+REG_FUNC_MUX_CTRL_3: /* 32 bits */
+ .word 0xfffe1010
+REG_FUNC_MUX_CTRL_4: /* 32 bits */
+ .word 0xfffe1014
+REG_FUNC_MUX_CTRL_5: /* 32 bits */
+ .word 0xfffe1018
+REG_FUNC_MUX_CTRL_6: /* 32 bits */
+ .word 0xfffe101c
+REG_FUNC_MUX_CTRL_7: /* 32 bits */
+ .word 0xfffe1020
+REG_FUNC_MUX_CTRL_8: /* 32 bits */
+ .word 0xfffe1024
+REG_FUNC_MUX_CTRL_9: /* 32 bits */
+ .word 0xfffe1028
+REG_FUNC_MUX_CTRL_A: /* 32 bits */
+ .word 0xfffe102C
+REG_FUNC_MUX_CTRL_B: /* 32 bits */
+ .word 0xfffe1030
+REG_FUNC_MUX_CTRL_C: /* 32 bits */
+ .word 0xfffe1034
+REG_FUNC_MUX_CTRL_D: /* 32 bits */
+ .word 0xfffe1038
+REG_PULL_DWN_CTRL_0: /* 32 bits */
+ .word 0xfffe1040
+REG_PULL_DWN_CTRL_1: /* 32 bits */
+ .word 0xfffe1044
+REG_PULL_DWN_CTRL_2: /* 32 bits */
+ .word 0xfffe1048
+REG_PULL_DWN_CTRL_3: /* 32 bits */
+ .word 0xfffe104c
+REG_VOLTAGE_CTRL_0: /* 32 bits */
+ .word 0xfffe1060
+REG_TEST_DBG_CTRL_0: /* 32 bits */
+ .word 0xfffe1070
+REG_MOD_CONF_CTRL_0: /* 32 bits */
+ .word 0xfffe1080
+REG_TC_IMIF_PRIO: /* 32 bits */
+ .word 0xfffecc00
+REG_TC_EMIFS_PRIO: /* 32 bits */
+ .word 0xfffecc04
+REG_TC_EMIFF_PRIO: /* 32 bits */
+ .word 0xfffecc08
+REG_TC_EMIFS_CONFIG: /* 32 bits */
+ .word 0xfffecc0c
+REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */
+ .word 0xfffecc10
+REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */
+ .word 0xfffecc14
+REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */
+ .word 0xfffecc18
+REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */
+ .word 0xfffecc1c
+REG_TC_EMIFF_SDRAM_CONFIG: /* 32 bits */
+ .word 0xfffecc20
+REG_TC_EMIFF_MRS: /* 32 bits */
+ .word 0xfffecc24
+/* MPU clock/reset/power mode control registers */
+REG_ARM_CKCTL: /* 16 bits */
+ .word 0xfffece00
+REG_ARM_IDLECT2: /* 16 bits */
+ .word 0xfffece08
+REG_ARM_RSTCT2: /* 16 bits */
+ .word 0xfffece14
+REG_ARM_SYSST: /* 16 bits */
+ .word 0xfffece18
+/* DPLL control registers */
+REG_DPLL1_CTL: /* 16 bits */
+ .word 0xfffecf00
+/* identification code register */
+REG_IDCODE: /* 32 bits */
+ .word 0xfffed404
+
+/* Innovator specific */
+REG_FPGA_LED_DIGIT: /* 8 bits (not used on Innovator) */
+ .word 0x08000003
+REG_FPGA_POWER: /* 8 bits */
+ .word 0x08000005
+REG_FPGA_AUDIO: /* 8 bits (not used on Innovator) */
+ .word 0x0800000c
+REG_FPGA_DIP_SWITCH: /* 8 bits (not used on Innovator) */
+ .word 0x0800000e
+
+VAL_COMP_MODE_CTRL_0:
+ .word 0x0000eaef
+VAL_FUNC_MUX_CTRL_4:
+ .word 0x00000000
+VAL_FUNC_MUX_CTRL_5:
+ .word 0x00000000
+VAL_FUNC_MUX_CTRL_6:
+ .word 0x00000001
+VAL_FUNC_MUX_CTRL_7:
+ .word 0x00000000
+VAL_FUNC_MUX_CTRL_8:
+ .word 0x10001200
+VAL_FUNC_MUX_CTRL_9:
+ .word 0x01201012
+VAL_FUNC_MUX_CTRL_A:
+ .word 0x00000248
+VAL_FUNC_MUX_CTRL_B:
+ .word 0x00000248
+VAL_FUNC_MUX_CTRL_C:
+ .word 0x09000000
+VAL_FUNC_MUX_CTRL_D:
+ .word 0x00000000
+VAL_PULL_DWN_CTRL_0:
+ .word 0x11a10000
+VAL_PULL_DWN_CTRL_1:
+ .word 0x2e047fff
+VAL_PULL_DWN_CTRL_2:
+ .word 0xffd603a6
+VAL_PULL_DWN_CTRL_3:
+ .word 0x00003e03
+VAL_VOLTAGE_CTRL_0:
+ .word 0x00000007
+VAL_TEST_DBG_CTRL_0:
+ /* See Errata 4.13, This works around a SRAM bug, for chips below ES2.5 .
+ * This slows down internal SRAM accesses.
+ */
+ .word 0x00000007
+VAL_MOD_CONF_CTRL_0:
+ .word 0x0b000008
+VAL_ARM_CKCTL:
+ .word 0x010f
+VAL_DPLL1_CTL:
+ .word 0x2710
+VAL_TC_EMIFS_CS1_CONFIG_PRELIM:
+ .word 0x00001149
+VAL_TC_EMIFS_CS2_CONFIG_PRELIM:
+ .word 0x00004158
+VAL_TC_EMIFS_CS0_CONFIG:
+ .word 0x002130b0
+VAL_TC_EMIFS_CS1_CONFIG:
+ .word 0x0000f559
+VAL_TC_EMIFS_CS2_CONFIG:
+ .word 0x000055f0
+VAL_TC_EMIFS_CS3_CONFIG:
+ .word 0x00003331
+VAL_TC_EMIFF_SDRAM_CONFIG:
+ .word 0x010290fc
+VAL_TC_EMIFF_MRS:
+ .word 0x00000027
--- /dev/null
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void flash__init (void);
+static void ether__init (void);
+
+static inline void delay (unsigned long loops)
+{
+ __asm__ volatile ("1:\n"
+ "subs %0, %1, #1\n"
+ "bne 1b":"=r" (loops):"0" (loops));
+}
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+ /* arch number of OMAP 1510-Board */
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP_INNOVATOR;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = 0x10000100;
+
+/* kk - this speeds up your boot a quite a bit. However to make it
+ * work, you need make sure your kernel startup flush bug is fixed.
+ * ... rkw ...
+ */
+ icache_enable ();
+
+ flash__init ();
+ ether__init ();
+ return 0;
+}
+
+
+int misc_init_r (void)
+{
+ /* volatile ushort *gdir = (ushort *) (GPIO_DIR_CONTROL_REG); */
+ /* volatile ushort *mdir = (ushort *) (MPUIO_DIR_CONTROL_REG); */
+
+ /* setup gpio direction to match board (no floats!) */
+ /**gdir = 0xCFF9; */
+ /**mdir = 0x103F; */
+
+ return (0);
+}
+
+/******************************
+ Routine:
+ Description:
+******************************/
+static void flash__init (void)
+{
+#define CS0_CHIP_SELECT_REG 0xfffecc10
+#define CS3_CHIP_SELECT_REG 0xfffecc1c
+#define EMIFS_GlB_Config_REG 0xfffecc0c
+
+ {
+ unsigned int regval;
+
+ regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG);
+ regval = regval | 0x0001; /* Turn off write protection for flash devices. */
+ if (regval & 0x0002) {
+ regval = regval & 0xfffd; /* Swap CS0 and CS3 so that flash is visible at 0x0 and eeprom at 0x0c000000. */
+ /* If, instead, you want to reference flash at 0x0c000000, then it seemed the following were necessary. */
+ /* *((volatile unsigned int *)CS0_CHIP_SELECT_REG) = 0x202090; / * Overrides head.S setting of 0x212090 */
+ /* *((volatile unsigned int *)CS3_CHIP_SELECT_REG) = 0x202090; / * Let's flash chips be fully functional. */
+ }
+ *((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval;
+ }
+}
+
+
+/******************************
+ Routine:
+ Description:
+******************************/
+static void ether__init (void)
+{
+#define ETH_CONTROL_REG 0x0800000b
+ /* take the Ethernet controller out of reset and wait
+ * for the EEPROM load to complete.
+ */
+ *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
+ udelay (3);
+}
+
+
+int dram_init (void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+ return 0;
+}
--- /dev/null
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := omap1610innovator.o flash.o
+SOBJS := lowlevel_init.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+#
+# (C) Copyright 2002
+# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
+# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+#
+# (C) Copyright 2003
+# Texas Instruments, <www.ti.com>
+# Kshitij Gupta <Kshitij@ti.com>
+#
+# TI Innovator board with OMAP1610 (ARM925EJS) cpu
+# see http://www.ti.com/ for more information on Texas Instruments
+#
+# Innovator has 1 bank of 256 MB SDRAM
+# Physical Address:
+# 1000'0000 to 2000'0000
+#
+#
+# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000
+# (mem base + reserved)
+#
+# we load ourself to 1108'0000
+#
+#
+
+
+TEXT_BASE = 0x11080000
--- /dev/null
+/*
+ * (C) Copyright 2001
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2001-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <linux/byteorder/swab.h>
+
+#define PHYS_FLASH_SECT_SIZE 0x00020000 /* 256 KB sectors (x2) */
+flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
+
+/* Board support for 1 or 2 flash devices */
+#undef FLASH_PORT_WIDTH32
+#define FLASH_PORT_WIDTH16
+
+#ifdef FLASH_PORT_WIDTH16
+#define FLASH_PORT_WIDTH ushort
+#define FLASH_PORT_WIDTHV vu_short
+#define SWAP(x) __swab16(x)
+#else
+#define FLASH_PORT_WIDTH ulong
+#define FLASH_PORT_WIDTHV vu_long
+#define SWAP(x) __swab32(x)
+#endif
+
+#define FPW FLASH_PORT_WIDTH
+#define FPWV FLASH_PORT_WIDTHV
+
+#define mb() __asm__ __volatile__ ("" : : : "memory")
+
+
+/* Flash Organization Structure */
+typedef struct OrgDef {
+ unsigned int sector_number;
+ unsigned int sector_size;
+} OrgDef;
+
+
+/* Flash Organizations */
+OrgDef OrgIntel_28F256L18T[] = {
+ {4, 32 * 1024}, /* 4 * 32kBytes sectors */
+ {255, 128 * 1024}, /* 255 * 128kBytes sectors */
+};
+
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+unsigned long flash_init (void);
+static ulong flash_get_size (FPW * addr, flash_info_t * info);
+static int write_data (flash_info_t * info, ulong dest, FPW data);
+static void flash_get_offsets (ulong base, flash_info_t * info);
+void inline spin_wheel (void);
+void flash_print_info (flash_info_t * info);
+void flash_unprotect_sectors (FPWV * addr);
+int flash_erase (flash_info_t * info, int s_first, int s_last);
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt);
+void flash_unlock(flash_info_t * info);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+ int i;
+ ulong size = 0;
+
+ for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
+ switch (i) {
+ case 0:
+ flash_get_size ((FPW *) CONFIG_SYS_FLASH_BASE, &flash_info[i]);
+ flash_get_offsets (CONFIG_SYS_FLASH_BASE, &flash_info[i]);
+ /* to reset the lock bit */
+ flash_unlock(&flash_info[i]);
+ break;
+ default:
+ panic ("configured too many flash banks!\n");
+ break;
+ }
+ size += flash_info[i].size;
+ }
+
+ /* Protect monitor and environment sectors
+ */
+ flash_protect (FLAG_PROTECT_SET,
+ CONFIG_SYS_FLASH_BASE,
+ CONFIG_SYS_FLASH_BASE + monitor_flash_len - 1, &flash_info[0]);
+
+ flash_protect (FLAG_PROTECT_SET,
+ CONFIG_ENV_ADDR,
+ CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]);
+
+ return size;
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_unlock(flash_info_t * info)
+{
+ int j;
+ for (j=2;j<CONFIG_SYS_MAX_FLASH_SECT;j++){
+ FPWV *addr = (FPWV *) (info->start[j]);
+ flash_unprotect_sectors (addr);
+ *addr = (FPW) 0x00500050;/* clear status register */
+ *addr = (FPW) 0x00FF00FF;/* resest to read mode */
+ }
+}
+
+/*-----------------------------------------------------------------------
+ */
+static void flash_get_offsets (ulong base, flash_info_t * info)
+{
+ int i;
+ OrgDef *pOrgDef;
+
+ pOrgDef = OrgIntel_28F256L18T;
+ if (info->flash_id == FLASH_UNKNOWN) {
+ return;
+ }
+
+ if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
+ for (i = 0; i < info->sector_count; i++) {
+ if (i > 255) {
+ info->start[i] = base + (i * 0x8000);
+ info->protect[i] = 0;
+ } else {
+ info->start[i] = base +
+ (i * PHYS_FLASH_SECT_SIZE);
+ info->protect[i] = 0;
+ }
+ }
+ }
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info (flash_info_t * info)
+{
+ int i;
+
+ if (info->flash_id == FLASH_UNKNOWN) {
+ printf ("missing or unknown FLASH type\n");
+ return;
+ }
+
+ switch (info->flash_id & FLASH_VENDMASK) {
+ case FLASH_MAN_INTEL:
+ printf ("INTEL ");
+ break;
+ default:
+ printf ("Unknown Vendor ");
+ break;
+ }
+
+ switch (info->flash_id & FLASH_TYPEMASK) {
+ case FLASH_28F256L18T:
+ printf ("FLASH 28F256L18T\n");
+ break;
+ default:
+ printf ("Unknown Chip Type\n");
+ break;
+ }
+
+ printf (" Size: %ld MB in %d Sectors\n",
+ info->size >> 20, info->sector_count);
+
+ printf (" Sector Start Addresses:");
+ for (i = 0; i < info->sector_count; ++i) {
+ if ((i % 5) == 0)
+ printf ("\n ");
+ printf (" %08lX%s",
+ info->start[i], info->protect[i] ? " (RO)" : " ");
+ }
+ printf ("\n");
+ return;
+}
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+static ulong flash_get_size (FPW * addr, flash_info_t * info)
+{
+ volatile FPW value;
+
+ /* Write auto select command: read Manufacturer ID */
+ addr[0x5555] = (FPW) 0x00AA00AA;
+ addr[0x2AAA] = (FPW) 0x00550055;
+ addr[0x5555] = (FPW) 0x00900090;
+
+ mb ();
+ value = addr[0];
+
+ switch (value) {
+
+ case (FPW) INTEL_MANUFACT:
+ info->flash_id = FLASH_MAN_INTEL;
+ break;
+
+ default:
+ info->flash_id = FLASH_UNKNOWN;
+ info->sector_count = 0;
+ info->size = 0;
+ addr[0] = (FPW) 0x00FF00FF; /* restore read mode */
+ return (0); /* no or unknown flash */
+ }
+
+ mb ();
+ value = addr[1]; /* device ID */
+ switch (value) {
+
+ case (FPW) (INTEL_ID_28F256L18T):
+ info->flash_id += FLASH_28F256L18T;
+ info->sector_count = 259;
+ info->size = 0x02000000;
+ break; /* => 32 MB */
+
+ default:
+ info->flash_id = FLASH_UNKNOWN;
+ break;
+ }
+
+ if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
+ printf ("** ERROR: sector count %d > max (%d) **\n",
+ info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
+ info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
+ }
+
+ addr[0] = (FPW) 0x00FF00FF; /* restore read mode */
+
+ return (info->size);
+}
+
+
+/* unprotects a sector for write and erase
+ * on some intel parts, this unprotects the entire chip, but it
+ * wont hurt to call this additional times per sector...
+ */
+void flash_unprotect_sectors (FPWV * addr)
+{
+#define PD_FINTEL_WSMS_READY_MASK 0x0080
+
+ *addr = (FPW) 0x00500050; /* clear status register */
+
+ /* this sends the clear lock bit command */
+ *addr = (FPW) 0x00600060;
+ *addr = (FPW) 0x00D000D0;
+}
+
+
+/*-----------------------------------------------------------------------
+ */
+
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+ int flag, prot, sect;
+ ulong type, start, last;
+ int rcode = 0;
+
+ if ((s_first < 0) || (s_first > s_last)) {
+ if (info->flash_id == FLASH_UNKNOWN) {
+ printf ("- missing\n");
+ } else {
+ printf ("- no sectors to erase\n");
+ }
+ return 1;
+ }
+
+ type = (info->flash_id & FLASH_VENDMASK);
+ if ((type != FLASH_MAN_INTEL)) {
+ printf ("Can't erase unknown flash type %08lx - aborted\n",
+ info->flash_id);
+ return 1;
+ }
+
+ prot = 0;
+ for (sect = s_first; sect <= s_last; ++sect) {
+ if (info->protect[sect]) {
+ prot++;
+ }
+ }
+
+ if (prot) {
+ printf ("- Warning: %d protected sectors will not be erased!\n",
+ prot);
+ } else {
+ printf ("\n");
+ }
+
+
+ start = get_timer (0);
+ last = start;
+
+ /* Disable interrupts which might cause a timeout here */
+ flag = disable_interrupts ();
+
+ /* Start erase on unprotected sectors */
+ for (sect = s_first; sect <= s_last; sect++) {
+ if (info->protect[sect] == 0) { /* not protected */
+ FPWV *addr = (FPWV *) (info->start[sect]);
+ FPW status;
+
+ printf ("Erasing sector %2d ... ", sect);
+
+ flash_unprotect_sectors (addr);
+
+ /* arm simple, non interrupt dependent timer */
+ reset_timer_masked ();
+
+ *addr = (FPW) 0x00500050;/* clear status register */
+ *addr = (FPW) 0x00200020;/* erase setup */
+ *addr = (FPW) 0x00D000D0;/* erase confirm */
+
+ while (((status =
+ *addr) & (FPW) 0x00800080) !=
+ (FPW) 0x00800080) {
+ if (get_timer_masked () >
+ CONFIG_SYS_FLASH_ERASE_TOUT) {
+ printf ("Timeout\n");
+ /* suspend erase */
+ *addr = (FPW) 0x00B000B0;
+ /* reset to read mode */
+ *addr = (FPW) 0x00FF00FF;
+ rcode = 1;
+ break;
+ }
+ }
+
+ /* clear status register cmd. */
+ *addr = (FPW) 0x00500050;
+ *addr = (FPW) 0x00FF00FF;/* resest to read mode */
+ printf (" done\n");
+ }
+ }
+ return rcode;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ * 4 - Flash not identified
+ */
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+ ulong cp, wp;
+ FPW data;
+ int count, i, l, rc, port_width;
+
+ if (info->flash_id == FLASH_UNKNOWN) {
+ return 4;
+ }
+/* get lower word aligned address */
+#ifdef FLASH_PORT_WIDTH16
+ wp = (addr & ~1);
+ port_width = 2;
+#else
+ wp = (addr & ~3);
+ port_width = 4;
+#endif
+
+ /*
+ * handle unaligned start bytes
+ */
+ if ((l = addr - wp) != 0) {
+ data = 0;
+ for (i = 0, cp = wp; i < l; ++i, ++cp) {
+ data = (data << 8) | (*(uchar *) cp);
+ }
+ for (; i < port_width && cnt > 0; ++i) {
+ data = (data << 8) | *src++;
+ --cnt;
+ ++cp;
+ }
+ for (; cnt == 0 && i < port_width; ++i, ++cp) {
+ data = (data << 8) | (*(uchar *) cp);
+ }
+
+ if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+ return (rc);
+ }
+ wp += port_width;
+ }
+
+ /*
+ * handle word aligned part
+ */
+ count = 0;
+ while (cnt >= port_width) {
+ data = 0;
+ for (i = 0; i < port_width; ++i) {
+ data = (data << 8) | *src++;
+ }
+ if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+ return (rc);
+ }
+ wp += port_width;
+ cnt -= port_width;
+ if (count++ > 0x800) {
+ spin_wheel ();
+ count = 0;
+ }
+ }
+
+ if (cnt == 0) {
+ return (0);
+ }
+
+ /*
+ * handle unaligned tail bytes
+ */
+ data = 0;
+ for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
+ data = (data << 8) | *src++;
+ --cnt;
+ }
+ for (; i < port_width; ++i, ++cp) {
+ data = (data << 8) | (*(uchar *) cp);
+ }
+
+ return (write_data (info, wp, SWAP (data)));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word or halfword to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_data (flash_info_t * info, ulong dest, FPW data)
+{
+ FPWV *addr = (FPWV *) dest;
+ ulong status;
+ int flag;
+
+ /* Check if Flash is (sufficiently) erased */
+ if ((*addr & data) != data) {
+ printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr);
+ return (2);
+ }
+ /* Disable interrupts which might cause a timeout here */
+ flag = disable_interrupts ();
+ *addr = (FPW) 0x00400040; /* write setup */
+ *addr = data;
+
+ /* arm simple, non interrupt dependent timer */
+ reset_timer_masked ();
+
+ /* wait while polling the status register */
+ while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
+ if (get_timer_masked () > CONFIG_SYS_FLASH_WRITE_TOUT) {
+ *addr = (FPW) 0x00FF00FF; /* restore read mode */
+ return (1);
+ }
+ }
+ *addr = (FPW) 0x00FF00FF; /* restore read mode */
+ return (0);
+}
+
+void inline spin_wheel (void)
+{
+ static int p = 0;
+ static char w[] = "\\/-";
+
+ printf ("\010%c", w[p]);
+ (++p == 3) ? (p = 0) : 0;
+}
--- /dev/null
+/*
+ * Board specific setup info
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+
+#if defined(CONFIG_OMAP1610)
+#include <./configs/omap1510.h>
+#endif
+
+
+_TEXT_BASE:
+ .word TEXT_BASE /* sdram load addr from config.mk */
+
+.globl lowlevel_init
+lowlevel_init:
+
+
+ /*------------------------------------------------------*
+ *mask all IRQs by setting all bits in the INTMR default*
+ *------------------------------------------------------*/
+ mov r1, #0xffffffff
+ ldr r0, =REG_IHL1_MIR
+ str r1, [r0]
+ ldr r0, =REG_IHL2_MIR
+ str r1, [r0]
+
+ /*------------------------------------------------------*
+ * Set up ARM CLM registers (IDLECT1) *
+ *------------------------------------------------------*/
+ ldr r0, REG_ARM_IDLECT1
+ ldr r1, VAL_ARM_IDLECT1
+ str r1, [r0]
+
+ /*------------------------------------------------------*
+ * Set up ARM CLM registers (IDLECT2) *
+ *------------------------------------------------------*/
+ ldr r0, REG_ARM_IDLECT2
+ ldr r1, VAL_ARM_IDLECT2
+ str r1, [r0]
+
+ /*------------------------------------------------------*
+ * Set up ARM CLM registers (IDLECT3) *
+ *------------------------------------------------------*/
+ ldr r0, REG_ARM_IDLECT3
+ ldr r1, VAL_ARM_IDLECT3
+ str r1, [r0]
+
+#ifdef CONFIG_CS_AUTOBOOT /* do the setup depending on boot mode */
+ ldr r0, CONF_STATUS
+ ldr r1, [r0]
+ tst r1, #0x02
+ beq disable_wd /* booting from RAM, skip setup */
+#endif
+
+ mov r1, #0x01 /* PER_EN bit */
+ ldr r0, REG_ARM_RSTCT2
+ strh r1, [r0] /* CLKM; Peripheral reset. */
+
+ /* Set CLKM to Sync-Scalable */
+ /* I supposedly need to enable the dsp clock before switching */
+ mov r1, #0x0000
+ ldr r0, REG_ARM_SYSST
+ strh r1, [r0]
+ mov r0, #0x400
+1:
+ subs r0, r0, #0x1 /* wait for any bubbles to finish */
+ bne 1b
+ ldr r1, VAL_ARM_CKCTL
+ ldr r0, REG_ARM_CKCTL
+ strh r1, [r0]
+
+ /* a few nops to let settle */
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+
+ /* setup DPLL 1 */
+ /* Ramp up the clock to 96Mhz */
+ ldr r1, VAL_DPLL1_CTL
+ ldr r0, REG_DPLL1_CTL
+ strh r1, [r0]
+ ands r1, r1, #0x10 /* Check if PLL is enabled. */
+ beq lock_end /* Do not look for lock if BYPASS selected */
+2:
+ ldrh r1, [r0]
+ ands r1, r1, #0x01 /* Check the LOCK bit.*/
+ beq 2b /* loop until bit goes hi. */
+lock_end:
+
+
+ /*------------------------------------------------------*
+ * Turn off the watchdog during init... *
+ *------------------------------------------------------*/
+disable_wd:
+ ldr r0, REG_WATCHDOG
+ ldr r1, WATCHDOG_VAL1
+ str r1, [r0]
+ ldr r1, WATCHDOG_VAL2
+ str r1, [r0]
+ ldr r0, REG_WSPRDOG
+ ldr r1, WSPRDOG_VAL1
+ str r1, [r0]
+ ldr r0, REG_WWPSDOG
+
+watch1Wait:
+ ldr r1, [r0]
+ tst r1, #0x10
+ bne watch1Wait
+
+ ldr r0, REG_WSPRDOG
+ ldr r1, WSPRDOG_VAL2
+ str r1, [r0]
+ ldr r0, REG_WWPSDOG
+watch2Wait:
+ ldr r1, [r0]
+ tst r1, #0x10
+ bne watch2Wait
+
+
+ /* Set memory timings corresponding to the new clock speed */
+
+ /* Check execution location to determine current execution location
+ * and branch to appropriate initialization code.
+ */
+ /* Load physical SDRAM base. */
+ mov r0, #0x10000000
+ /* Get current execution location. */
+ mov r1, pc
+ /* Compare. */
+ cmp r1, r0
+ /* Skip over EMIF-fast initialization if running from SDRAM. */
+ bge skip_sdram
+
+ /*
+ * Delay for SDRAM initialization.
+ */
+ mov r3, #0x1800 /* value should be checked */
+3:
+ subs r3, r3, #0x1 /* Decrement count */
+ bne 3b
+
+
+ /*
+ * Set SDRAM control values. Disable refresh before MRS command.
+ */
+
+ /* mobile ddr operation */
+ ldr r0, REG_SDRAM_OPERATION
+ mov r2, #07
+ str r2, [r0]
+
+ /* config register */
+ ldr r0, REG_SDRAM_CONFIG
+ ldr r1, SDRAM_CONFIG_VAL
+ str r1, [r0]
+
+ /* manual command register */
+ ldr r0, REG_SDRAM_MANUAL_CMD
+ /* issue set cke high */
+ mov r1, #CMD_SDRAM_CKE_SET_HIGH
+ str r1, [r0]
+ /* issue nop */
+ mov r1, #CMD_SDRAM_NOP
+ str r1, [r0]
+
+ mov r2, #0x0100
+waitMDDR1:
+ subs r2, r2, #1
+ bne waitMDDR1 /* delay loop */
+
+ /* issue precharge */
+ mov r1, #CMD_SDRAM_PRECHARGE
+ str r1, [r0]
+
+ /* issue autorefresh x 2 */
+ mov r1, #CMD_SDRAM_AUTOREFRESH
+ str r1, [r0]
+ str r1, [r0]
+
+ /* mrs register ddr mobile */
+ ldr r0, REG_SDRAM_MRS
+ mov r1, #0x33
+ str r1, [r0]
+
+ /* emrs1 low-power register */
+ ldr r0, REG_SDRAM_EMRS1
+ /* self refresh on all banks */
+ mov r1, #0
+ str r1, [r0]
+
+ ldr r0, REG_DLL_URD_CONTROL
+ ldr r1, DLL_URD_CONTROL_VAL
+ str r1, [r0]
+
+ ldr r0, REG_DLL_LRD_CONTROL
+ ldr r1, DLL_LRD_CONTROL_VAL
+ str r1, [r0]
+
+ ldr r0, REG_DLL_WRT_CONTROL
+ ldr r1, DLL_WRT_CONTROL_VAL
+ str r1, [r0]
+
+ /* delay loop */
+ mov r2, #0x0100
+waitMDDR2:
+ subs r2, r2, #1
+ bne waitMDDR2
+
+ /*
+ * Delay for SDRAM initialization.
+ */
+ mov r3, #0x1800
+4:
+ subs r3, r3, #1 /* Decrement count. */
+ bne 4b
+ b common_tc
+
+skip_sdram:
+
+ ldr r0, REG_SDRAM_CONFIG
+ ldr r1, SDRAM_CONFIG_VAL
+ str r1, [r0]
+
+common_tc:
+ /* slow interface */
+ ldr r1, VAL_TC_EMIFS_CS0_CONFIG
+ ldr r0, REG_TC_EMIFS_CS0_CONFIG
+ str r1, [r0] /* Chip Select 0 */
+
+ ldr r1, VAL_TC_EMIFS_CS1_CONFIG
+ ldr r0, REG_TC_EMIFS_CS1_CONFIG
+ str r1, [r0] /* Chip Select 1 */
+ ldr r1, VAL_TC_EMIFS_CS3_CONFIG
+ ldr r0, REG_TC_EMIFS_CS3_CONFIG
+ str r1, [r0] /* Chip Select 3 */
+
+#ifdef CONFIG_H2_OMAP1610
+ /* inserting additional 2 clock cycle hold time for LAN */
+ ldr r0, REG_TC_EMIFS_CS1_ADVANCED
+ ldr r1, VAL_TC_EMIFS_CS1_ADVANCED
+ str r1, [r0]
+#endif
+ /* Start MPU Timer 1 */
+ ldr r0, REG_MPU_LOAD_TIMER
+ ldr r1, VAL_MPU_LOAD_TIMER
+ str r1, [r0]
+
+ ldr r0, REG_MPU_CNTL_TIMER
+ ldr r1, VAL_MPU_CNTL_TIMER
+ str r1, [r0]
+
+ /* back to arch calling code */
+ mov pc, lr
+
+ /* the literal pools origin */
+ .ltorg
+
+#ifdef CONFIG_CS_AUTOBOOT
+CONF_STATUS:
+ .word 0xfffe1130 /* 32 bits */
+#endif
+
+REG_TC_EMIFS_CONFIG: /* 32 bits */
+ .word 0xfffecc0c
+REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */
+ .word 0xfffecc10
+REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */
+ .word 0xfffecc14
+REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */
+ .word 0xfffecc18
+REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */
+ .word 0xfffecc1c
+
+#ifdef CONFIG_H2_OMAP1610
+REG_TC_EMIFS_CS1_ADVANCED: /* 32 bits */
+ .word 0xfffecc54
+#endif
+
+/* MPU clock/reset/power mode control registers */
+REG_ARM_CKCTL: /* 16 bits */
+ .word 0xfffece00
+
+REG_ARM_IDLECT3: /* 16 bits */
+ .word 0xfffece24
+REG_ARM_IDLECT2: /* 16 bits */
+ .word 0xfffece08
+REG_ARM_IDLECT1: /* 16 bits */
+ .word 0xfffece04
+
+REG_ARM_RSTCT2: /* 16 bits */
+ .word 0xfffece14
+REG_ARM_SYSST: /* 16 bits */
+ .word 0xfffece18
+/* DPLL control registers */
+REG_DPLL1_CTL: /* 16 bits */
+ .word 0xfffecf00
+
+/* Watch Dog register */
+/* secure watchdog stop */
+REG_WSPRDOG:
+ .word 0xfffeb048
+/* watchdog write pending */
+REG_WWPSDOG:
+ .word 0xfffeb034
+
+WSPRDOG_VAL1:
+ .word 0x0000aaaa
+WSPRDOG_VAL2:
+ .word 0x00005555
+
+/* SDRAM config is: auto refresh enabled, 16 bit 4 bank,
+ counter @8192 rows, 10 ns, 8 burst */
+REG_SDRAM_CONFIG:
+ .word 0xfffecc20
+
+/* Operation register */
+REG_SDRAM_OPERATION:
+ .word 0xfffecc80
+
+/* Manual command register */
+REG_SDRAM_MANUAL_CMD:
+ .word 0xfffecc84
+
+/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */
+REG_SDRAM_MRS:
+ .word 0xfffecc70
+
+/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */
+REG_SDRAM_EMRS1:
+ .word 0xfffecc78
+
+/* WRT DLL register */
+REG_DLL_WRT_CONTROL:
+ .word 0xfffecc68
+DLL_WRT_CONTROL_VAL:
+ .word 0x03f00002
+
+/* URD DLL register */
+REG_DLL_URD_CONTROL:
+ .word 0xfffeccc0
+DLL_URD_CONTROL_VAL:
+ .word 0x00800002
+
+/* LRD DLL register */
+REG_DLL_LRD_CONTROL:
+ .word 0xfffecccc
+
+REG_WATCHDOG:
+ .word 0xfffec808
+
+REG_MPU_LOAD_TIMER:
+ .word 0xfffec504
+REG_MPU_CNTL_TIMER:
+ .word 0xfffec500
+
+/* 96 MHz Samsung Mobile DDR */
+SDRAM_CONFIG_VAL:
+ .word 0x001200f4
+
+DLL_LRD_CONTROL_VAL:
+ .word 0x00800002
+
+VAL_ARM_CKCTL:
+ .word 0x3000
+VAL_DPLL1_CTL:
+ .word 0x2830
+
+#ifdef CONFIG_INNOVATOROMAP1610
+VAL_TC_EMIFS_CS0_CONFIG:
+ .word 0x002130b0
+VAL_TC_EMIFS_CS1_CONFIG:
+ .word 0x00001131
+VAL_TC_EMIFS_CS2_CONFIG:
+ .word 0x000055f0
+VAL_TC_EMIFS_CS3_CONFIG:
+ .word 0x88011131
+#endif
+
+#ifdef CONFIG_H2_OMAP1610
+VAL_TC_EMIFS_CS0_CONFIG:
+ .word 0x00203331
+VAL_TC_EMIFS_CS1_CONFIG:
+ .word 0x8180fff3
+VAL_TC_EMIFS_CS2_CONFIG:
+ .word 0xf800f22a
+VAL_TC_EMIFS_CS3_CONFIG:
+ .word 0x88011131
+VAL_TC_EMIFS_CS1_ADVANCED:
+ .word 0x00000022
+#endif
+
+VAL_TC_EMIFF_SDRAM_CONFIG:
+ .word 0x010290fc
+VAL_TC_EMIFF_MRS:
+ .word 0x00000027
+
+VAL_ARM_IDLECT1:
+ .word 0x00000400
+
+VAL_ARM_IDLECT2:
+ .word 0x00000886
+VAL_ARM_IDLECT3:
+ .word 0x00000015
+
+WATCHDOG_VAL1:
+ .word 0x000000f5
+WATCHDOG_VAL2:
+ .word 0x000000a0
+
+VAL_MPU_LOAD_TIMER:
+ .word 0xffffffff
+VAL_MPU_CNTL_TIMER:
+ .word 0xffffffa1
+
+/* command values */
+.equ CMD_SDRAM_NOP, 0x00000000
+.equ CMD_SDRAM_PRECHARGE, 0x00000001
+.equ CMD_SDRAM_AUTOREFRESH, 0x00000002
+.equ CMD_SDRAM_CKE_SET_HIGH, 0x00000007
--- /dev/null
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#if defined(CONFIG_OMAP1610)
+#include <./configs/omap1510.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_CS_AUTOBOOT
+unsigned long omap_flash_base;
+#endif
+
+void flash__init (void);
+void ether__init (void);
+void set_muxconf_regs (void);
+void peripheral_power_enable (void);
+
+#define COMP_MODE_ENABLE ((unsigned int)0x0000EAEF)
+
+static inline void delay (unsigned long loops)
+{
+ __asm__ volatile ("1:\n"
+ "subs %0, %1, #1\n"
+ "bne 1b":"=r" (loops):"0" (loops));
+}
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+ if (machine_is_omap_h2())
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP_H2;
+ else if (machine_is_omap_innovator())
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP_INNOVATOR;
+ else
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP_GENERIC;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = 0x10000100;
+
+ /* Configure MUX settings */
+ set_muxconf_regs ();
+ peripheral_power_enable ();
+
+/* this speeds up your boot a quite a bit. However to make it
+ * work, you need make sure your kernel startup flush bug is fixed.
+ * ... rkw ...
+ */
+ icache_enable ();
+
+ flash__init ();
+ ether__init ();
+ return 0;
+}
+
+
+int misc_init_r (void)
+{
+ /* currently empty */
+ return (0);
+}
+
+/******************************
+ Routine:
+ Description:
+******************************/
+void flash__init (void)
+{
+#define EMIFS_GlB_Config_REG 0xfffecc0c
+ unsigned int regval;
+
+#ifdef CONFIG_CS_AUTOBOOT
+ /* Check swapping of CS0 and CS3, set flash base accordingly */
+ omap_flash_base = ((*((u32 *)OMAP_EMIFS_CONFIG_REG) & 0x02) == 0) ?
+ PHYS_FLASH_1_BM0 : PHYS_FLASH_1_BM1;
+#endif
+ regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG);
+ /* Turn off write protection for flash devices. */
+ regval = regval | 0x0001;
+ *((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval;
+}
+/*************************************************************
+ Routine:ether__init
+ Description: take the Ethernet controller out of reset and wait
+ for the EEPROM load to complete.
+*************************************************************/
+void ether__init (void)
+{
+#define ETH_CONTROL_REG 0x0400030b
+
+#ifdef CONFIG_H2_OMAP1610
+ #define LAN_RESET_REGISTER 0x0400001c
+
+ /* The debug board on which the lan chip resides may not be powered
+ * ON at the same time as the OMAP chip. So wait in a loop until the
+ * lan reset register (on the debug board) is available (powered on)
+ * and reset the lan chip.
+ */
+
+ *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000;
+ do {
+ *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0001;
+ udelay (3);
+ } while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0001);
+
+ do {
+ *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000;
+ udelay (3);
+ } while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0000);
+#endif
+
+ *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
+ udelay (3);
+}
+
+/******************************
+ Routine:
+ Description:
+******************************/
+int dram_init (void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+ return 0;
+}
+
+/******************************************************
+ Routine: set_muxconf_regs
+ Description: Setting up the configuration Mux registers
+ specific to the hardware
+*******************************************************/
+void set_muxconf_regs (void)
+{
+ volatile unsigned int *MuxConfReg;
+ /* set each registers to its reset value; */
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
+ /* setup for UART1 */
+ *MuxConfReg &= ~(0x02000000); /* bit 25 */
+ /* setup for UART2 */
+ *MuxConfReg &= ~(0x01000000); /* bit 24 */
+ /* Disable Uwire CS Hi-Z */
+ *MuxConfReg |= 0x08000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_3);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_4);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_5);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_6);
+ /*setup mux for UART3 */
+ *MuxConfReg |= 0x00000001; /* bit3, 1, 0 (mux0 5,5,26) */
+ *MuxConfReg &= ~0x0000003e;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_7);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_8);
+ /* Disable Uwire CS Hi-Z */
+ *MuxConfReg |= 0x00001200; /*bit 9 for CS0 12 for CS3 */
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_9);
+ /* Need to turn on bits 21 and 12 in FUNC_MUX_CTRL_9 so the */
+ /* hardware will actually use TX and RTS based on bit 25 in */
+ /* FUNC_MUX_CTRL_0. I told you this thing was screwy! */
+ *MuxConfReg |= 0x00201000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_A);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_B);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_C);
+ /* setup for UART2 */
+ /* Need to turn on bits 27 and 24 in FUNC_MUX_CTRL_C so the */
+ /* hardware will actually use TX and RTS based on bit 24 in */
+ /* FUNC_MUX_CTRL_0. */
+ *MuxConfReg |= 0x09000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_0);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_1);
+ *MuxConfReg = 0x00000000;
+ /* mux setup for SD/MMC driver */
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_2);
+ *MuxConfReg &= 0xFFFE0FFF;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_3);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
+ /* bit 13 for MMC2 XOR_CLK */
+ *MuxConfReg &= ~(0x00002000);
+ /* bit 29 for UART 1 */
+ *MuxConfReg &= ~(0x00002000);
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
+ /* Configure for USB. Turn on VBUS_CTRL and VBUS_MODE. */
+ *MuxConfReg |= 0x000C0000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int)USB_TRANSCEIVER_CTRL);
+ *MuxConfReg &= ~(0x00000070);
+ *MuxConfReg &= ~(0x00000008);
+ *MuxConfReg |= 0x00000003;
+ *MuxConfReg |= 0x00000180;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
+ /* bit 17, software controls VBUS */
+ *MuxConfReg &= ~(0x00020000);
+ /* Enable USB 48 and 12M clocks */
+ *MuxConfReg |= 0x00000200;
+ *MuxConfReg &= ~(0x00000180);
+ /*2.75V for MMCSDIO1 */
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) VOLTAGE_CTRL_0);
+ *MuxConfReg = 0x00001FE7;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PU_PD_SEL_0);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PU_PD_SEL_1);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PU_PD_SEL_3);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PU_PD_SEL_4);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_4);
+ *MuxConfReg = 0x00000000;
+ /* Turn on UART2 48 MHZ clock */
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
+ *MuxConfReg |= 0x40000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) USB_OTG_CTRL);
+ /* setup for USB VBus detection OMAP161x */
+ *MuxConfReg |= 0x00040000; /* bit 18 */
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
+ /* PullUps for SD/MMC driver */
+ *MuxConfReg |= ~(0xFFFE0FFF);
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int)COMP_MODE_CTRL_0);
+ *MuxConfReg = COMP_MODE_ENABLE;
+}
+
+/******************************************************
+ Routine: peripheral_power_enable
+ Description: Enable the power for UART1
+*******************************************************/
+void peripheral_power_enable (void)
+{
+#define UART1_48MHZ_ENABLE ((unsigned short)0x0200)
+#define SW_CLOCK_REQUEST ((volatile unsigned short *)0xFFFE0834)
+
+ *SW_CLOCK_REQUEST |= UART1_48MHZ_ENABLE;
+}
--- /dev/null
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := omap2420h4.o mem.o sys_info.o
+SOBJS := lowlevel_init.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+#
+# (C) Copyright 2004
+# Texas Instruments, <www.ti.com>
+#
+# TI H4 board with OMAP2420 (ARM1136) cpu
+# see http://www.ti.com/ for more information on Texas Instruments
+#
+# H4 has 1 bank of 32MB or 64MB mDDR-SDRAM on CS0
+# H4 has 1 bank of 32MB or 00MB mDDR-SDRAM on CS1
+# Physical Address:
+# 8000'0000 (bank0)
+# A000/0000 (bank1) ES2 will be configurable
+# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+
+# For use with external or internal boots.
+TEXT_BASE = 0x80e80000
+
+# Used with full SRAM boot.
+# This is either with a GP system or a signed boot image.
+# easiest, and safest way to go if you can.
+#TEXT_BASE = 0x40270000
+
+
+# Handy to get symbols to debug ROM version.
+#TEXT_BASE = 0x0
+#TEXT_BASE = 0x08000000
+#TEXT_BASE = 0x04000000
--- /dev/null
+/*
+ * Board specific setup info
+ *
+ * (C) Copyright 2004
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/omap2420.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/clocks.h>
+
+_TEXT_BASE:
+ .word TEXT_BASE /* sdram load addr from config.mk */
+
+/**************************************************************************
+ * cpy_clk_code: relocates clock code into SRAM where its safer to execute
+ * R1 = SRAM destination address.
+ *************************************************************************/
+.global cpy_clk_code
+ cpy_clk_code:
+ /* Copy DPLL code into SRAM */
+ adr r0, go_to_speed /* get addr of clock setting code */
+ mov r2, #384 /* r2 size to copy (div by 32 bytes) */
+ mov r1, r1 /* r1 <- dest address (passed in) */
+ add r2, r2, r0 /* r2 <- source end address */
+next2:
+ ldmia r0!, {r3-r10} /* copy from source address [r0] */
+ stmia r1!, {r3-r10} /* copy to target address [r1] */
+ cmp r0, r2 /* until source end address [r2] */
+ bne next2
+ mov pc, lr /* back to caller */
+
+/* ****************************************************************************
+ * go_to_speed: -Moves to bypass, -Commits clock dividers, -puts dpll at speed
+ * -executed from SRAM.
+ * R0 = PRCM_CLKCFG_CTRL - addr of valid reg
+ * R1 = CM_CLKEN_PLL - addr dpll ctlr reg
+ * R2 = dpll value
+ * R3 = CM_IDLEST_CKGEN - addr dpll lock wait
+ ******************************************************************************/
+.global go_to_speed
+ go_to_speed:
+ sub sp, sp, #0x4 /* get some stack space */
+ str r4, [sp] /* save r4's value */
+
+ /* move into fast relock bypass */
+ ldr r8, pll_ctl_add
+ mov r4, #0x2
+ str r4, [r8]
+ ldr r4, pll_stat
+block:
+ ldr r8, [r4] /* wait for bypass to take effect */
+ and r8, r8, #0x3
+ cmp r8, #0x1
+ bne block
+
+ /* set new dpll dividers _after_ in bypass */
+ ldr r4, pll_div_add
+ ldr r8, pll_div_val
+ str r8, [r4]
+
+ /* now prepare GPMC (flash) for new dpll speed */
+ /* flash needs to be stable when we jump back to it */
+ ldr r4, cfg3_0_addr
+ ldr r8, cfg3_0_val
+ str r8, [r4]
+ ldr r4, cfg4_0_addr
+ ldr r8, cfg4_0_val
+ str r8, [r4]
+ ldr r4, cfg1_0_addr
+ ldr r8, [r4]
+ orr r8, r8, #0x3 /* up gpmc divider */
+ str r8, [r4]
+
+ /* setup to 2x loop though code. The first loop pre-loads the
+ * icache, the 2nd commits the prcm config, and locks the dpll
+ */
+ mov r4, #0x1000 /* spin spin spin */
+ mov r8, #0x4 /* first pass condition & set registers */
+ cmp r8, #0x4
+2:
+ ldrne r8, [r3] /* DPLL lock check */
+ and r8, r8, #0x7
+ cmp r8, #0x2
+ beq 4f
+3:
+ subeq r8, r8, #0x1
+ streq r8, [r0] /* commit dividers (2nd time) */
+ nop
+lloop1:
+ sub r4, r4, #0x1 /* Loop currently necessary else bad jumps */
+ nop
+ cmp r4, #0x0
+ bne lloop1
+ mov r4, #0x40000
+ cmp r8, #0x1
+ nop
+ streq r2, [r1] /* lock dpll (2nd time) */
+ nop
+lloop2:
+ sub r4, r4, #0x1 /* loop currently necessary else bad jumps */
+ nop
+ cmp r4, #0x0
+ bne lloop2
+ mov r4, #0x40000
+ cmp r8, #0x1
+ nop
+ ldreq r8, [r3] /* get lock condition for dpll */
+ cmp r8, #0x4 /* first time though? */
+ bne 2b
+ moveq r8, #0x2 /* set to dpll check condition. */
+ beq 3b /* if condition not true branch */
+4:
+ ldr r4, [sp]
+ add sp, sp, #0x4 /* return stack space */
+ mov pc, lr /* back to caller, locked */
+
+_go_to_speed: .word go_to_speed
+
+/* these constants need to be close for PIC code */
+cfg3_0_addr:
+ .word GPMC_CONFIG3_0
+cfg3_0_val:
+ .word H4_24XX_GPMC_CONFIG3_0
+cfg4_0_addr:
+ .word GPMC_CONFIG4_0
+cfg4_0_val:
+ .word H4_24XX_GPMC_CONFIG4_0
+cfg1_0_addr:
+ .word GPMC_CONFIG1_0
+pll_ctl_add:
+ .word CM_CLKEN_PLL
+pll_stat:
+ .word CM_IDLEST_CKGEN
+pll_div_add:
+ .word CM_CLKSEL1_PLL
+pll_div_val:
+ .word DPLL_VAL /* DPLL setting (300MHz default) */
+
+.globl lowlevel_init
+lowlevel_init:
+ ldr sp, SRAM_STACK
+ str ip, [sp] /* stash old link register */
+ mov ip, lr /* save link reg across call */
+ bl s_init /* go setup pll,mux,memory */
+ ldr ip, [sp] /* restore save ip */
+ mov lr, ip /* restore link reg */
+
+ /* map interrupt controller */
+ ldr r0, VAL_INTH_SETUP
+ mcr p15, 0, r0, c15, c2, 4
+
+ /* back to arch calling code */
+ mov pc, lr
+
+ /* the literal pools origin */
+ .ltorg
+
+REG_CONTROL_STATUS:
+ .word CONTROL_STATUS
+VAL_INTH_SETUP:
+ .word PERIFERAL_PORT_BASE
+SRAM_STACK:
+ .word LOW_LEVEL_SRAM_STACK
--- /dev/null
+/*
+ * (C) Copyright 2004
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/omap2420.h>
+#include <asm/io.h>
+#include <asm/arch/bits.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/clocks.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/sys_info.h>
+
+/************************************************************
+ * sdelay() - simple spin loop. Will be constant time as
+ * its generally used in 12MHz bypass conditions only. This
+ * is necessary until timers are accessible.
+ *
+ * not inline to increase chances its in cache when called
+ *************************************************************/
+void sdelay (unsigned long loops)
+{
+ __asm__ volatile ("1:\n" "subs %0, %1, #1\n"
+ "bne 1b":"=r" (loops):"0" (loops));
+}
+
+/*********************************************************************************
+ * prcm_init() - inits clocks for PRCM as defined in clocks.h (config II default).
+ * -- called from SRAM, or Flash (using temp SRAM stack).
+ *********************************************************************************/
+void prcm_init(void)
+{
+ u32 div;
+ void (*f_lock_pll) (u32, u32, u32, u32);
+ extern void *_end_vect, *_start;
+
+ f_lock_pll = (void *)((u32)&_end_vect - (u32)&_start + SRAM_VECT_CODE);
+
+ __raw_writel(0, CM_FCLKEN1_CORE); /* stop all clocks to reduce ringing */
+ __raw_writel(0, CM_FCLKEN2_CORE); /* may not be necessary */
+ __raw_writel(0, CM_ICLKEN1_CORE);
+ __raw_writel(0, CM_ICLKEN2_CORE);
+
+ __raw_writel(DPLL_OUT, CM_CLKSEL2_PLL); /* set DPLL out */
+ __raw_writel(MPU_DIV, CM_CLKSEL_MPU); /* set MPU divider */
+ __raw_writel(DSP_DIV, CM_CLKSEL_DSP); /* set dsp and iva dividers */
+ __raw_writel(GFX_DIV, CM_CLKSEL_GFX); /* set gfx dividers */
+
+ div = BUS_DIV;
+ __raw_writel(div, CM_CLKSEL1_CORE);/* set L3/L4/USB/Display/Vlnc/SSi dividers */
+ sdelay(1000);
+
+ if(running_in_sram()){
+ /* If running fully from SRAM this is OK. The Flash bus drops out for just a little.
+ * but then comes back. If running from Flash this sequence kills you, thus you need
+ * to run it using CONFIG_PARTIAL_SRAM.
+ */
+ __raw_writel(MODE_BYPASS_FAST, CM_CLKEN_PLL); /* go to bypass, fast relock */
+ wait_on_value(BIT0|BIT1, BIT0, CM_IDLEST_CKGEN, LDELAY); /* wait till in bypass */
+ sdelay(1000);
+ /* set clock selection and dpll dividers. */
+ __raw_writel(DPLL_VAL, CM_CLKSEL1_PLL); /* set pll for target rate */
+ __raw_writel(COMMIT_DIVIDERS, PRCM_CLKCFG_CTRL); /* commit dividers */
+ sdelay(10000);
+ __raw_writel(DPLL_LOCK, CM_CLKEN_PLL); /* enable dpll */
+ sdelay(10000);
+ wait_on_value(BIT0|BIT1, BIT1, CM_IDLEST_CKGEN, LDELAY); /*wait for dpll lock */
+ }else if(running_in_flash()){
+ /* if running from flash, need to jump to small relocated code area in SRAM.
+ * This is the only safe spot to do configurations from.
+ */
+ (*f_lock_pll)(PRCM_CLKCFG_CTRL, CM_CLKEN_PLL, DPLL_LOCK, CM_IDLEST_CKGEN);
+ }
+
+ __raw_writel(DPLL_LOCK|APLL_LOCK, CM_CLKEN_PLL); /* enable apll */
+ wait_on_value(BIT8, BIT8, CM_IDLEST_CKGEN, LDELAY); /* wait for apll lock */
+ sdelay(1000);
+}
+
+/**************************************************************************
+ * make_cs1_contiguous() - for es2 and above remap cs1 behind cs0 to allow
+ * command line mem=xyz use all memory with out discontigious support
+ * compiled in. Could do it at the ATAG, but there really is two banks...
+ * Called as part of 2nd phase DDR init.
+ **************************************************************************/
+void make_cs1_contiguous(void)
+{
+ u32 size, a_add_low, a_add_high;
+
+ size = get_sdr_cs_size(SDRC_CS0_OSET);
+ size /= SZ_32M; /* find size to offset CS1 */
+ a_add_high = (size & 3) << 8; /* set up low field */
+ a_add_low = (size & 0x3C) >> 2; /* set up high field */
+ __raw_writel((a_add_high|a_add_low),SDRC_CS_CFG);
+
+}
+
+/********************************************************
+ * mem_ok() - test used to see if timings are correct
+ * for a part. Helps in gussing which part
+ * we are currently using.
+ *******************************************************/
+u32 mem_ok(void)
+{
+ u32 val1, val2;
+ u32 pattern = 0x12345678;
+
+ __raw_writel(0x0,OMAP2420_SDRC_CS0+0x400); /* clear pos A */
+ __raw_writel(pattern, OMAP2420_SDRC_CS0); /* pattern to pos B */
+ __raw_writel(0x0,OMAP2420_SDRC_CS0+4); /* remove pattern off the bus */
+ val1 = __raw_readl(OMAP2420_SDRC_CS0+0x400); /* get pos A value */
+ val2 = __raw_readl(OMAP2420_SDRC_CS0); /* get val2 */
+
+ if ((val1 != 0) || (val2 != pattern)) /* see if pos A value changed*/
+ return(0);
+ else
+ return(1);
+}
+
+
+/********************************************************
+ * sdrc_init() - init the sdrc chip selects CS0 and CS1
+ * - early init routines, called from flash or
+ * SRAM.
+ *******************************************************/
+void sdrc_init(void)
+{
+ #define EARLY_INIT 1
+ do_sdrc_init(SDRC_CS0_OSET, EARLY_INIT); /* only init up first bank here */
+}
+
+/*************************************************************************
+ * do_sdrc_init(): initialize the SDRAM for use.
+ * -called from low level code with stack only.
+ * -code sets up SDRAM timing and muxing for 2422 or 2420.
+ * -optimal settings can be placed here, or redone after i2c
+ * inspection of board info
+ *
+ * This is a bit ugly, but should handle all memory moduels
+ * used with the H4. The first time though this code from s_init()
+ * we configure the first chip select. Later on we come back and
+ * will configure the 2nd chip select if it exists.
+ *
+ **************************************************************************/
+void do_sdrc_init(u32 offset, u32 early)
+{
+ u32 cpu, dllen=0, rev, common=0, cs0=0, pmask=0, pass_type, mtype;
+ sdrc_data_t *sdata; /* do not change type */
+ u32 a, b, r;
+
+ static const sdrc_data_t sdrc_2422 =
+ {
+ H4_2422_SDRC_SHARING, H4_2422_SDRC_MDCFG_0_DDR, 0 , H4_2422_SDRC_ACTIM_CTRLA_0,
+ H4_2422_SDRC_ACTIM_CTRLB_0, H4_2422_SDRC_RFR_CTRL, H4_2422_SDRC_MR_0_DDR,
+ 0, H4_2422_SDRC_DLLAB_CTRL
+ };
+ static const sdrc_data_t sdrc_2420 =
+ {
+ H4_2420_SDRC_SHARING, H4_2420_SDRC_MDCFG_0_DDR, H4_2420_SDRC_MDCFG_0_SDR,
+ H4_2420_SDRC_ACTIM_CTRLA_0, H4_2420_SDRC_ACTIM_CTRLB_0,
+ H4_2420_SDRC_RFR_CTRL, H4_2420_SDRC_MR_0_DDR, H4_2420_SDRC_MR_0_SDR,
+ H4_2420_SDRC_DLLAB_CTRL
+ };
+
+ if (offset == SDRC_CS0_OSET)
+ cs0 = common = 1; /* int regs shared between both chip select */
+
+ cpu = get_cpu_type();
+ rev = get_cpu_rev();
+
+ /* warning generated, though code generation is correct. this may bite later,
+ * but is ok for now. there is only so much C code you can do on stack only
+ * operation.
+ */
+ if (cpu == CPU_2422){
+ sdata = (sdrc_data_t *)&sdrc_2422;
+ pass_type = STACKED;
+ } else{
+ sdata = (sdrc_data_t *)&sdrc_2420;
+ pass_type = IP_DDR;
+ }
+
+ __asm__ __volatile__("": : :"memory"); /* limit compiler scope */
+
+ /* u-boot is compiled to run in DDR or SRAM at 8xxxxxxx or 4xxxxxxx.
+ * If we are running in flash prior to relocation and we use data
+ * here which is not pc relative we need to get the address correct.
+ * We need to find the current flash mapping to dress up the initial
+ * pointer load. As long as this is const data we should be ok.
+ */
+ if((early) && running_in_flash()){
+ sdata = (sdrc_data_t *)(((u32)sdata & 0x0003FFFF) | get_gpmc0_base());
+ /* NOR internal boot offset is 0x4000 from xloader signature */
+ if(running_from_internal_boot())
+ sdata = (sdrc_data_t *)((u32)sdata + 0x4000);
+ }
+
+ if (!early && (((mtype = get_mem_type()) == DDR_COMBO)||(mtype == DDR_STACKED))) {
+ if(mtype == DDR_COMBO){
+ pmask = BIT2;/* combo part has a shared CKE signal, can't use feature */
+ pass_type = COMBO_DDR; /* CS1 config */
+ __raw_writel((__raw_readl(SDRC_POWER)) & ~pmask, SDRC_POWER);
+ }
+ if(rev != CPU_2420_2422_ES1) /* for es2 and above smooth things out */
+ make_cs1_contiguous();
+ }
+
+next_mem_type:
+ if (common) { /* do a SDRC reset between types to clear regs*/
+ __raw_writel(SOFTRESET, SDRC_SYSCONFIG); /* reset sdrc */
+ wait_on_value(BIT0, BIT0, SDRC_STATUS, 12000000);/* wait till reset done set */
+ __raw_writel(0, SDRC_SYSCONFIG); /* clear soft reset */
+ __raw_writel(sdata->sdrc_sharing, SDRC_SHARING);
+#ifdef POWER_SAVE
+ __raw_writel(__raw_readl(SMS_SYSCONFIG)|SMART_IDLE, SMS_SYSCONFIG);
+ __raw_writel(sdata->sdrc_sharing|SMART_IDLE, SDRC_SHARING);
+ __raw_writel((__raw_readl(SDRC_POWER)|BIT6), SDRC_POWER);
+#endif
+ }
+
+ if ((pass_type == IP_DDR) || (pass_type == STACKED)) /* (IP ddr-CS0),(2422-CS0/CS1) */
+ __raw_writel(sdata->sdrc_mdcfg_0_ddr, SDRC_MCFG_0+offset);
+ else if (pass_type == COMBO_DDR){ /* (combo-CS0/CS1) */
+ __raw_writel(H4_2420_COMBO_MDCFG_0_DDR,SDRC_MCFG_0+offset);
+ } else if (pass_type == IP_SDR){ /* ip sdr-CS0 */
+ __raw_writel(sdata->sdrc_mdcfg_0_sdr, SDRC_MCFG_0+offset);
+ }
+
+ a = sdata->sdrc_actim_ctrla_0;
+ b = sdata->sdrc_actim_ctrlb_0;
+ r = sdata->sdrc_dllab_ctrl;
+
+ /* work around ES1 DDR issues */
+ if((pass_type != IP_SDR) && (rev == CPU_2420_2422_ES1)){
+ a = H4_242x_SDRC_ACTIM_CTRLA_0_ES1;
+ b = H4_242x_SDRC_ACTIM_CTRLB_0_ES1;
+ r = H4_242x_SDRC_RFR_CTRL_ES1;
+ }
+
+ if (cs0) {
+ __raw_writel(a, SDRC_ACTIM_CTRLA_0);
+ __raw_writel(b, SDRC_ACTIM_CTRLB_0);
+ } else {
+ __raw_writel(a, SDRC_ACTIM_CTRLA_1);
+ __raw_writel(b, SDRC_ACTIM_CTRLB_1);
+ }
+ __raw_writel(r, SDRC_RFR_CTRL+offset);
+
+ /* init sequence for mDDR/mSDR using manual commands (DDR is a bit different) */
+ __raw_writel(CMD_NOP, SDRC_MANUAL_0+offset);
+ sdelay(5000); /* susposed to be 100us per design spec for mddr/msdr */
+ __raw_writel(CMD_PRECHARGE, SDRC_MANUAL_0+offset);
+ __raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_0+offset);
+ __raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_0+offset);
+
+ /*
+ * CSx SDRC Mode Register
+ * Burst length = (4 - DDR) (2-SDR)
+ * Serial mode
+ * CAS latency = x
+ */
+ if(pass_type == IP_SDR)
+ __raw_writel(sdata->sdrc_mr_0_sdr, SDRC_MR_0+offset);
+ else
+ __raw_writel(sdata->sdrc_mr_0_ddr, SDRC_MR_0+offset);
+
+ /* NOTE: ES1 242x _BUG_ DLL + External Bandwidth fix*/
+ if (rev == CPU_2420_2422_ES1){
+ dllen = (BIT0|BIT3); /* es1 clear both bit0 and bit3 */
+ __raw_writel((__raw_readl(SMS_CLASS_ARB0)|BURSTCOMPLETE_GROUP7)
+ ,SMS_CLASS_ARB0);/* enable bust complete for lcd */
+ }
+ else
+ dllen = BIT0|BIT1; /* es2, clear bit0, and 1 (set phase to 72) */
+
+ /* enable & load up DLL with good value for 75MHz, and set phase to 90
+ * ES1 recommends 90 phase, ES2 recommends 72 phase.
+ */
+ if (common && (pass_type != IP_SDR)) {
+ __raw_writel(sdata->sdrc_dllab_ctrl, SDRC_DLLA_CTRL);
+ __raw_writel(sdata->sdrc_dllab_ctrl & ~(BIT2|dllen), SDRC_DLLA_CTRL);
+ __raw_writel(sdata->sdrc_dllab_ctrl, SDRC_DLLB_CTRL);
+ __raw_writel(sdata->sdrc_dllab_ctrl & ~(BIT2|dllen) , SDRC_DLLB_CTRL);
+ }
+ sdelay(90000);
+
+ if(mem_ok())
+ return; /* STACKED, other configued type */
+ ++pass_type; /* IPDDR->COMBODDR->IPSDR for CS0 */
+ goto next_mem_type;
+}
+
+/*****************************************************
+ * gpmc_init(): init gpmc bus
+ * Init GPMC for x16, MuxMode (SDRAM in x32).
+ * This code can only be executed from SRAM or SDRAM.
+ *****************************************************/
+void gpmc_init(void)
+{
+ u32 mux=0, mtype, mwidth, rev, tval;
+
+ rev = get_cpu_rev();
+ if (rev == CPU_2420_2422_ES1)
+ tval = 1;
+ else
+ tval = 0; /* disable bit switched meaning */
+
+ /* global settings */
+ __raw_writel(0x10, GPMC_SYSCONFIG); /* smart idle */
+ __raw_writel(0x0, GPMC_IRQENABLE); /* isr's sources masked */
+ __raw_writel(tval, GPMC_TIMEOUT_CONTROL);/* timeout disable */
+#ifdef CONFIG_SYS_NAND_BOOT
+ __raw_writel(0x001, GPMC_CONFIG); /* set nWP, disable limited addr */
+#else
+ __raw_writel(0x111, GPMC_CONFIG); /* set nWP, disable limited addr */
+#endif
+
+ /* discover bus connection from sysboot */
+ if (is_gpmc_muxed() == GPMC_MUXED)
+ mux = BIT9;
+ mtype = get_gpmc0_type();
+ mwidth = get_gpmc0_width();
+
+ /* setup cs0 */
+ __raw_writel(0x0, GPMC_CONFIG7_0); /* disable current map */
+ sdelay(1000);
+
+#ifdef CONFIG_SYS_NAND_BOOT
+ __raw_writel(H4_24XX_GPMC_CONFIG1_0|mtype|mwidth, GPMC_CONFIG1_0);
+#else
+ __raw_writel(H4_24XX_GPMC_CONFIG1_0|mux|mtype|mwidth, GPMC_CONFIG1_0);
+#endif
+
+#ifdef PRCM_CONFIG_III
+ __raw_writel(H4_24XX_GPMC_CONFIG2_0, GPMC_CONFIG2_0);
+#endif
+ __raw_writel(H4_24XX_GPMC_CONFIG3_0, GPMC_CONFIG3_0);
+ __raw_writel(H4_24XX_GPMC_CONFIG4_0, GPMC_CONFIG4_0);
+#ifdef PRCM_CONFIG_III
+ __raw_writel(H4_24XX_GPMC_CONFIG5_0, GPMC_CONFIG5_0);
+ __raw_writel(H4_24XX_GPMC_CONFIG6_0, GPMC_CONFIG6_0);
+#endif
+ __raw_writel(H4_24XX_GPMC_CONFIG7_0, GPMC_CONFIG7_0);/* enable new mapping */
+ sdelay(2000);
+
+ /* setup cs1 */
+ __raw_writel(0, GPMC_CONFIG7_1); /* disable any mapping */
+ sdelay(1000);
+ __raw_writel(H4_24XX_GPMC_CONFIG1_1|mux, GPMC_CONFIG1_1);
+ __raw_writel(H4_24XX_GPMC_CONFIG2_1, GPMC_CONFIG2_1);
+ __raw_writel(H4_24XX_GPMC_CONFIG3_1, GPMC_CONFIG3_1);
+ __raw_writel(H4_24XX_GPMC_CONFIG4_1, GPMC_CONFIG4_1);
+ __raw_writel(H4_24XX_GPMC_CONFIG5_1, GPMC_CONFIG5_1);
+ __raw_writel(H4_24XX_GPMC_CONFIG6_1, GPMC_CONFIG6_1);
+ __raw_writel(H4_24XX_GPMC_CONFIG7_1, GPMC_CONFIG7_1); /* enable mapping */
+ sdelay(2000);
+}
--- /dev/null
+/*
+ * (C) Copyright 2004
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <asm/arch/omap2420.h>
+#include <asm/io.h>
+#include <asm/arch/bits.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/sys_info.h>
+#include <asm/arch/mem.h>
+#include <i2c.h>
+#include <asm/mach-types.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void wait_for_command_complete(unsigned int wd_base);
+
+/*******************************************************
+ * Routine: delay
+ * Description: spinning delay to use before udelay works
+ ******************************************************/
+static inline void delay (unsigned long loops)
+{
+ __asm__ volatile ("1:\n" "subs %0, %1, #1\n"
+ "bne 1b":"=r" (loops):"0" (loops));
+}
+
+/*****************************************
+ * Routine: board_init
+ * Description: Early hardware init.
+ *****************************************/
+int board_init (void)
+{
+ gpmc_init(); /* in SRAM or SDRM, finish GPMC */
+
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP_H4; /* board id for linux */
+ gd->bd->bi_boot_params = (OMAP2420_SDRC_CS0+0x100); /* adress of boot parameters */
+
+ return 0;
+}
+
+/**********************************************************
+ * Routine: try_unlock_sram()
+ * Description: If chip is GP type, unlock the SRAM for
+ * general use.
+ ***********************************************************/
+void try_unlock_sram(void)
+{
+ /* if GP device unlock device SRAM for general use */
+ if (get_device_type() == GP_DEVICE) {
+ __raw_writel(0xFF, A_REQINFOPERM0);
+ __raw_writel(0xCFDE, A_READPERM0);
+ __raw_writel(0xCFDE, A_WRITEPERM0);
+ }
+}
+
+/**********************************************************
+ * Routine: s_init
+ * Description: Does early system init of muxing and clocks.
+ * - Called path is with sram stack.
+ **********************************************************/
+void s_init(void)
+{
+ int in_sdram = running_in_sdram();
+
+ watchdog_init();
+ set_muxconf_regs();
+ delay(100);
+ try_unlock_sram();
+
+ if(!in_sdram)
+ prcm_init();
+
+ peripheral_enable();
+ icache_enable();
+ if (!in_sdram)
+ sdrc_init();
+}
+
+/*******************************************************
+ * Routine: misc_init_r
+ * Description: Init ethernet (done here so udelay works)
+ ********************************************************/
+int misc_init_r (void)
+{
+ ether_init(); /* better done here so timers are init'ed */
+ return(0);
+}
+
+/****************************************
+ * Routine: watchdog_init
+ * Description: Shut down watch dogs
+ *****************************************/
+void watchdog_init(void)
+{
+ /* There are 4 watch dogs. 1 secure, and 3 general purpose.
+ * The ROM takes care of the secure one. Of the 3 GP ones,
+ * 1 can reset us directly, the other 2 only generate MPU interrupts.
+ */
+ __raw_writel(WD_UNLOCK1 ,WD2_BASE+WSPR);
+ wait_for_command_complete(WD2_BASE);
+ __raw_writel(WD_UNLOCK2 ,WD2_BASE+WSPR);
+
+#if MPU_WD_CLOCKED /* value 0x10 stick on aptix, BIT4 polarity seems oppsite*/
+ __raw_writel(WD_UNLOCK1 ,WD3_BASE+WSPR);
+ wait_for_command_complete(WD3_BASE);
+ __raw_writel(WD_UNLOCK2 ,WD3_BASE+WSPR);
+
+ __raw_writel(WD_UNLOCK1 ,WD4_BASE+WSPR);
+ wait_for_command_complete(WD4_BASE);
+ __raw_writel(WD_UNLOCK2 ,WD4_BASE+WSPR);
+#endif
+}
+
+/******************************************************
+ * Routine: wait_for_command_complete
+ * Description: Wait for posting to finish on watchdog
+ ******************************************************/
+void wait_for_command_complete(unsigned int wd_base)
+{
+ int pending = 1;
+ do {
+ pending = __raw_readl(wd_base+WWPS);
+ } while (pending);
+}
+
+/*******************************************************************
+ * Routine:ether_init
+ * Description: take the Ethernet controller out of reset and wait
+ * for the EEPROM load to complete.
+ ******************************************************************/
+void ether_init (void)
+{
+#ifdef CONFIG_DRIVER_LAN91C96
+ int cnt = 20;
+
+ __raw_writeb(0x3,OMAP2420_CTRL_BASE+0x10a); /*protect->gpio95 */
+
+ __raw_writew(0x0, LAN_RESET_REGISTER);
+ do {
+ __raw_writew(0x1, LAN_RESET_REGISTER);
+ udelay (100);
+ if (cnt == 0)
+ goto h4reset_err_out;
+ --cnt;
+ } while (__raw_readw(LAN_RESET_REGISTER) != 0x1);
+
+ cnt = 20;
+
+ do {
+ __raw_writew(0x0, LAN_RESET_REGISTER);
+ udelay (100);
+ if (cnt == 0)
+ goto h4reset_err_out;
+ --cnt;
+ } while (__raw_readw(LAN_RESET_REGISTER) != 0x0000);
+ udelay (1000);
+
+ *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
+ udelay (1000);
+
+ h4reset_err_out:
+ return;
+#endif
+}
+
+/**********************************************
+ * Routine: dram_init
+ * Description: sets uboots idea of sdram size
+ **********************************************/
+int dram_init (void)
+{
+ unsigned int size0=0,size1=0;
+ u32 mtype, btype, rev, cpu;
+ u8 chg_on = 0x5; /* enable charge of back up battery */
+ u8 vmode_on = 0x8C;
+ #define NOT_EARLY 0
+
+ i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); /* need this a bit early */
+
+ btype = get_board_type();
+ mtype = get_mem_type();
+ rev = get_cpu_rev();
+ cpu = get_cpu_type();
+
+ display_board_info(btype);
+ if (btype == BOARD_H4_MENELAUS){
+ update_mux(btype,mtype); /* combo part on menelaus */
+ i2c_write(I2C_MENELAUS, 0x20, 1, &chg_on, 1); /*fix POR reset bug */
+ i2c_write(I2C_MENELAUS, 0x2, 1, &vmode_on, 1); /* VCORE change on VMODE */
+ }
+
+ if ((mtype == DDR_COMBO) || (mtype == DDR_STACKED)) {
+ do_sdrc_init(SDRC_CS1_OSET, NOT_EARLY); /* init other chip select */
+ }
+ size0 = get_sdr_cs_size(SDRC_CS0_OSET);
+ size1 = get_sdr_cs_size(SDRC_CS1_OSET);
+
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = size0;
+ if(rev == CPU_2420_2422_ES1) /* ES1's 128MB remap granularity isn't worth doing */
+ gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+ else /* ES2 and above can remap at 32MB granularity */
+ gd->bd->bi_dram[1].start = PHYS_SDRAM_1+size0;
+ gd->bd->bi_dram[1].size = size1;
+
+ return 0;
+}
+
+/**********************************************************
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers
+ * specific to the hardware
+ *********************************************************/
+void set_muxconf_regs (void)
+{
+ muxSetupSDRC();
+ muxSetupGPMC();
+ muxSetupUsb0();
+ muxSetupUart3();
+ muxSetupI2C1();
+ muxSetupUART1();
+ muxSetupLCD();
+ muxSetupCamera();
+ muxSetupMMCSD();
+ muxSetupTouchScreen();
+ muxSetupHDQ();
+}
+
+/*****************************************************************
+ * Routine: peripheral_enable
+ * Description: Enable the clks & power for perifs (GPT2, UART1,...)
+ ******************************************************************/
+void peripheral_enable(void)
+{
+ unsigned int v, if_clks=0, func_clks=0;
+
+ /* Enable GP2 timer.*/
+ if_clks |= BIT4;
+ func_clks |= BIT4;
+ v = __raw_readl(CM_CLKSEL2_CORE) | 0x4; /* Sys_clk input OMAP2420_GPT2 */
+ __raw_writel(v, CM_CLKSEL2_CORE);
+ __raw_writel(0x1, CM_CLKSEL_WKUP);
+
+#ifdef CONFIG_SYS_NS16550
+ /* Enable UART1 clock */
+ func_clks |= BIT21;
+ if_clks |= BIT21;
+#endif
+ v = __raw_readl(CM_ICLKEN1_CORE) | if_clks; /* Interface clocks on */
+ __raw_writel(v,CM_ICLKEN1_CORE );
+ v = __raw_readl(CM_FCLKEN1_CORE) | func_clks; /* Functional Clocks on */
+ __raw_writel(v, CM_FCLKEN1_CORE);
+ delay(1000);
+
+#ifndef KERNEL_UPDATED
+ {
+#define V1 0xffffffff
+#define V2 0x00000007
+
+ __raw_writel(V1, CM_FCLKEN1_CORE);
+ __raw_writel(V2, CM_FCLKEN2_CORE);
+ __raw_writel(V1, CM_ICLKEN1_CORE);
+ __raw_writel(V1, CM_ICLKEN2_CORE);
+ }
+#endif
+}
+
+/****************************************
+ * Routine: muxSetupUsb0 (ostboot)
+ * Description: Setup usb muxing
+ *****************************************/
+void muxSetupUsb0(void)
+{
+ volatile uint8 *MuxConfigReg;
+ volatile uint32 *otgCtrlReg;
+
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_PUEN;
+ *MuxConfigReg &= (uint8)(~0x1F);
+
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_VP;
+ *MuxConfigReg &= (uint8)(~0x1F);
+
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_VM;
+ *MuxConfigReg &= (uint8)(~0x1F);
+
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_RCV;
+ *MuxConfigReg &= (uint8)(~0x1F);
+
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_TXEN;
+ *MuxConfigReg &= (uint8)(~0x1F);
+
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_SE0;
+ *MuxConfigReg &= (uint8)(~0x1F);
+
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_DAT;
+ *MuxConfigReg &= (uint8)(~0x1F);
+
+ /* setup for USB VBus detection */
+ otgCtrlReg = (volatile uint32 *)USB_OTG_CTRL;
+ *otgCtrlReg |= 0x00040000; /* bit 18 */
+}
+
+/****************************************
+ * Routine: muxSetupUart3 (ostboot)
+ * Description: Setup uart3 muxing
+ *****************************************/
+void muxSetupUart3(void)
+{
+ volatile uint8 *MuxConfigReg;
+
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_UART3_TX_IRTX;
+ *MuxConfigReg &= (uint8)(~0x1F);
+
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_UART3_RX_IRRX;
+ *MuxConfigReg &= (uint8)(~0x1F);
+}
+
+/****************************************
+ * Routine: muxSetupI2C1 (ostboot)
+ * Description: Setup i2c muxing
+ *****************************************/
+void muxSetupI2C1(void)
+{
+ volatile unsigned char *MuxConfigReg;
+
+ /* I2C1 Clock pin configuration, PIN = M19 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_I2C1_SCL;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* I2C1 Data pin configuration, PIN = L15 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_I2C1_SDA;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* Pull-up required on data line */
+ /* external pull-up already present. */
+ /* *MuxConfigReg |= 0x18 ;*/ /* Mode = 0, PullTypeSel=PU, PullUDEnable=Enabled */
+}
+
+/****************************************
+ * Routine: muxSetupUART1 (ostboot)
+ * Description: Set up uart1 muxing
+ *****************************************/
+void muxSetupUART1(void)
+{
+ volatile unsigned char *MuxConfigReg;
+
+ /* UART1_CTS pin configuration, PIN = D21 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_CTS;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* UART1_RTS pin configuration, PIN = H21 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_RTS;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* UART1_TX pin configuration, PIN = L20 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_TX;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* UART1_RX pin configuration, PIN = T21 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_RX;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+}
+
+/****************************************
+ * Routine: muxSetupLCD (ostboot)
+ * Description: Setup lcd muxing
+ *****************************************/
+void muxSetupLCD(void)
+{
+ volatile unsigned char *MuxConfigReg;
+
+ /* LCD_D0 pin configuration, PIN = Y7 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D0;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D1 pin configuration, PIN = P10 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D1;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D2 pin configuration, PIN = V8 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D2;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D3 pin configuration, PIN = Y8 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D3;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D4 pin configuration, PIN = W8 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D4;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D5 pin configuration, PIN = R10 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D5;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D6 pin configuration, PIN = Y9 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D6;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D7 pin configuration, PIN = V9 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D7;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D8 pin configuration, PIN = W9 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D8;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D9 pin configuration, PIN = P11 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D9;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D10 pin configuration, PIN = V10 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D10;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D11 pin configuration, PIN = Y10 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D11;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D12 pin configuration, PIN = W10 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D12;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D13 pin configuration, PIN = R11 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D13;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D14 pin configuration, PIN = V11 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D14;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D15 pin configuration, PIN = W11 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D15;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D16 pin configuration, PIN = P12 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D16;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_D17 pin configuration, PIN = R12 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D17;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_PCLK pin configuration, PIN = W6 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_PCLK;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_VSYNC pin configuration, PIN = V7 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_VSYNC;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_HSYNC pin configuration, PIN = Y6 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_HSYNC;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* LCD_ACBIAS pin configuration, PIN = W7 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_ACBIAS;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+}
+
+/****************************************
+ * Routine: muxSetupCamera (ostboot)
+ * Description: Setup camera muxing
+ *****************************************/
+void muxSetupCamera(void)
+{
+ volatile unsigned char *MuxConfigReg;
+
+ /* CAMERA_RSTZ pin configuration, PIN = Y16 */
+ /* CAM_RST is connected through the I2C IO expander.*/
+ /* MuxConfigReg = (volatile unsigned char *), CONTROL_PADCONF_SYS_NRESWARM*/
+ /* *MuxConfigReg = 0x00 ; / * Mode = 0, PUPD=Disabled */
+
+ /* CAMERA_XCLK pin configuration, PIN = U3 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_XCLK;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* CAMERA_LCLK pin configuration, PIN = V5 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_LCLK;
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* CAMERA_VSYNC pin configuration, PIN = U2 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_VS,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* CAMERA_HSYNC pin configuration, PIN = T3 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_HS,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* CAMERA_DAT0 pin configuration, PIN = T4 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D0,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* CAMERA_DAT1 pin configuration, PIN = V2 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D1,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* CAMERA_DAT2 pin configuration, PIN = V3 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D2,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* CAMERA_DAT3 pin configuration, PIN = U4 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D3,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* CAMERA_DAT4 pin configuration, PIN = W2 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D4,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* CAMERA_DAT5 pin configuration, PIN = V4 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D5,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* CAMERA_DAT6 pin configuration, PIN = W3 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D6,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* CAMERA_DAT7 pin configuration, PIN = Y2 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D7,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* CAMERA_DAT8 pin configuration, PIN = Y4 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D8,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* CAMERA_DAT9 pin configuration, PIN = V6 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D9,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+}
+
+/****************************************
+ * Routine: muxSetupMMCSD (ostboot)
+ * Description: set up MMC muxing
+ *****************************************/
+void muxSetupMMCSD(void)
+{
+ volatile unsigned char *MuxConfigReg;
+
+ /* SDMMC_CLKI pin configuration, PIN = H15 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CLKI,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* SDMMC_CLKO pin configuration, PIN = G19 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CLKO,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* SDMMC_CMD pin configuration, PIN = H18 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CMD,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+ /* External pull-ups are present. */
+ /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */
+
+ /* SDMMC_DAT0 pin configuration, PIN = F20 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT0,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+ /* External pull-ups are present. */
+ /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */
+
+ /* SDMMC_DAT1 pin configuration, PIN = H14 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT1,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+ /* External pull-ups are present. */
+ /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */
+
+ /* SDMMC_DAT2 pin configuration, PIN = E19 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT2,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+ /* External pull-ups are present. */
+ /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */
+
+ /* SDMMC_DAT3 pin configuration, PIN = D19 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT3,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+ /* External pull-ups are present. */
+ /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */
+
+ /* SDMMC_DDIR0 pin configuration, PIN = F19 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR0,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* SDMMC_DDIR1 pin configuration, PIN = E20 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR1,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* SDMMC_DDIR2 pin configuration, PIN = F18 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR2,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* SDMMC_DDIR3 pin configuration, PIN = E18 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR3,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* SDMMC_CDIR pin configuration, PIN = G18 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CMD_DIR,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* MMC_CD pin configuration, PIN = B3 ---2420IP ONLY---*/
+ /* MMC_CD for 2422IP=K1 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SDRC_A14,
+ *MuxConfigReg = 0x03 ; /* Mode = 3, PUPD=Disabled */
+
+ /* MMC_WP pin configuration, PIN = B4 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SDRC_A13,
+ *MuxConfigReg = 0x03 ; /* Mode = 3, PUPD=Disabled */
+}
+
+/******************************************
+ * Routine: muxSetupTouchScreen (ostboot)
+ * Description: Set up touch screen muxing
+ *******************************************/
+void muxSetupTouchScreen(void)
+{
+ volatile unsigned char *MuxConfigReg;
+
+ /* SPI1_CLK pin configuration, PIN = U18 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_CLK,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* SPI1_MOSI pin configuration, PIN = V20 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_SIMO,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* SPI1_MISO pin configuration, PIN = T18 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_SOMI,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* SPI1_nCS0 pin configuration, PIN = U19 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_NCS0,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+
+ /* PEN_IRQ pin configuration, PIN = P20 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MCBSP1_FSR,
+ *MuxConfigReg = 0x03 ; /* Mode = 3, PUPD=Disabled */
+}
+
+/****************************************
+ * Routine: muxSetupHDQ (ostboot)
+ * Description: setup 1wire mux
+ *****************************************/
+void muxSetupHDQ(void)
+{
+ volatile unsigned char *MuxConfigReg;
+
+ /* HDQ_SIO pin configuration, PIN = N18 */
+ MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_HDQ_SIO,
+ *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
+}
+
+/***************************************************************
+ * Routine: muxSetupGPMC (ostboot)
+ * Description: Configures balls which cam up in protected mode
+ ***************************************************************/
+void muxSetupGPMC(void)
+{
+ volatile uint8 *MuxConfigReg;
+ volatile unsigned int *MCR = (volatile unsigned int *)0x4800008C;
+
+ /* gpmc_io_dir */
+ *MCR = 0x19000000;
+
+ /* NOR FLASH CS0 */
+ /* signal - Gpmc_clk; pin - J4; offset - 0x0088; mode - 0; Byte-3 Pull/up - N/A */
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_D2_BYTE3,
+ *MuxConfigReg = 0x00 ;
+
+ /* signal - Gpmc_iodir; pin - n2; offset - 0x008C; mode - 1; Byte-3 Pull/up - N/A */
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE3,
+ *MuxConfigReg = 0x01 ;
+
+ /* MPDB(Multi Port Debug Port) CS1 */
+ /* signal - gpmc_ncs1; pin - N8; offset - 0x008C; mode - 0; Byte-1 Pull/up - N/A */
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE1,
+ *MuxConfigReg = 0x00 ;
+
+ /* signal - Gpmc_ncs2; pin - E2; offset - 0x008C; mode - 0; Byte-2 Pull/up - N/A */
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE2,
+ *MuxConfigReg = 0x00 ;
+}
+
+/****************************************************************
+ * Routine: muxSetupSDRC (ostboot)
+ * Description: Configures balls which come up in protected mode
+ ****************************************************************/
+void muxSetupSDRC(void)
+{
+ volatile uint8 *MuxConfigReg;
+
+ /* signal - sdrc_ncs1; pin - C12; offset - 0x00A0; mode - 0; Byte-1 Pull/up - N/A */
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_SDRC_NCS0_BYTE1,
+ *MuxConfigReg = 0x00 ;
+
+ /* signal - sdrc_a12; pin - D11; offset - 0x0030; mode - 0; Byte-2 Pull/up - N/A */
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_SDRC_A14_BYTE2,
+ *MuxConfigReg = 0x00 ;
+
+ /* signal - sdrc_cke1; pin - B13; offset - 0x00A0; mode - 0; Byte-3 Pull/up - N/A */
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_SDRC_NCS0_BYTE3,
+ *MuxConfigReg = 0x00;
+
+ if (get_cpu_type() == CPU_2422) {
+ MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_SDRC_A14_BYTE0,
+ *MuxConfigReg = 0x1b;
+ }
+}
+
+/*****************************************************************************
+ * Routine: update_mux()
+ * Description: Update balls which are different beween boards. All should be
+ * updated to match functionaly. However, I'm only updating ones
+ * which I'll be using for now. When power comes into play they
+ * all need updating.
+ *****************************************************************************/
+void update_mux(u32 btype,u32 mtype)
+{
+ u32 cpu, base = OMAP2420_CTRL_BASE;
+ cpu = get_cpu_type();
+
+ if (btype == BOARD_H4_MENELAUS) {
+ if (cpu == CPU_2420) {
+ /* PIN = B3, GPIO.0->KBR5, mode 3, (pun?),-DO-*/
+ __raw_writeb(0x3, base+0x30);
+ /* PIN = B13, GPIO.38->KBC6, mode 3, (pun?)-DO-*/
+ __raw_writeb(0x3, base+0xa3);
+ /* PIN = F1, GPIO.25->HSUSBxx mode 3, (for external HS USB)*/
+ /* PIN = H1, GPIO.26->HSUSBxx mode 3, (for external HS USB)*/
+ /* PIN = K1, GPMC_ncs6 mode 0, (on board nand access)*/
+ /* PIN = L2, GPMC_ncs67 mode 0, (for external HS USB)*/
+ /* PIN = M1 (HSUSBOTG) */
+ /* PIN = P1, GPIO.35->MEN_POK mode 3, (menelaus powerok)-DO-*/
+ __raw_writeb(0x3, base+0x9d);
+ /* PIN = U32, (WLAN_CLKREQ) */
+ /* PIN = Y11, WLAN */
+ /* PIN = AA4, GPIO.15->KBC2, mode 3, -DO- */
+ __raw_writeb(0x3, base+0xe7);
+ /* PIN = AA8, mDOC */
+ /* PIN = AA10, BT */
+ /* PIN = AA13, WLAN */
+ /* PIN = M18 GPIO.96->MMC2_WP mode 3 -DO- */
+ __raw_writeb(0x3, base+0x10e);
+ /* PIN = N19 GPIO.98->WLAN_INT mode 3 -DO- */
+ __raw_writeb(0x3, base+0x110);
+ /* PIN = J15 HHUSB */
+ /* PIN = H19 HSUSB */
+ /* PIN = W13, P13, R13, W16 ... */
+ /* PIN = V12 GPIO.25->I2C_CAMEN mode 3 -DO- */
+ __raw_writeb(0x3, base+0xde);
+ /* PIN = W19 sys_nirq->MENELAUS_INT mode 0 -DO- */
+ __raw_writeb(0x0, base+0x12c);
+ /* PIN = AA17->sys_clkreq mode 0 -DO- */
+ __raw_writeb(0x0, base+0x136);
+ } else if (cpu == CPU_2422) {
+ /* PIN = B3, GPIO.0->nc, mode 3, set above (pun?)*/
+ /* PIN = B13, GPIO.cke1->nc, mode 0, set above, (pun?)*/
+ /* PIN = F1, GPIO.25->HSUSBxx mode 3, (for external HS USB)*/
+ /* PIN = H1, GPIO.26->HSUSBxx mode 3, (for external HS USB)*/
+ /* PIN = K1, GPMC_ncs6 mode 0, (on board nand access)*/
+ __raw_writeb(0x0, base+0x92);
+ /* PIN = L2, GPMC_ncs67 mode 0, (for external HS USB)*/
+ /* PIN = M1 (HSUSBOTG) */
+ /* PIN = P1, GPIO.35->MEN_POK mode 3, (menelaus powerok)-DO-*/
+ __raw_writeb(0x3, base+0x10c);
+ /* PIN = U32, (WLAN_CLKREQ) */
+ /* PIN = AA4, GPIO.15->KBC2, mode 3, -DO- */
+ __raw_writeb(0x3, base+0x30);
+ /* PIN = AA8, mDOC */
+ /* PIN = AA10, BT */
+ /* PIN = AA12, WLAN */
+ /* PIN = M18 GPIO.96->MMC2_WP mode 3 -DO- */
+ __raw_writeb(0x3, base+0x10e);
+ /* PIN = N19 GPIO.98->WLAN_INT mode 3 -DO- */
+ __raw_writeb(0x3, base+0x110);
+ /* PIN = J15 HHUSB */
+ /* PIN = H19 HSUSB */
+ /* PIN = W13, P13, R13, W16 ... */
+ /* PIN = V12 GPIO.25->I2C_CAMEN mode 3 -DO- */
+ __raw_writeb(0x3, base+0xde);
+ /* PIN = W19 sys_nirq->MENELAUS_INT mode 0 -DO- */
+ __raw_writeb(0x0, base+0x12c);
+ /* PIN = AA17->sys_clkreq mode 0 -DO- */
+ __raw_writeb(0x0, base+0x136);
+ }
+
+ } else if (btype == BOARD_H4_SDP) {
+ if (cpu == CPU_2420) {
+ /* PIN = B3, GPIO.0->nc mode 3, set above (pun?)*/
+ /* PIN = B13, GPIO.cke1->nc, mode 0, set above, (pun?)*/
+ /* Pin = Y11 VLNQ */
+ /* Pin = AA4 VLNQ */
+ /* Pin = AA6 VLNQ */
+ /* Pin = AA8 VLNQ */
+ /* Pin = AA10 VLNQ */
+ /* Pin = AA12 VLNQ */
+ /* PIN = M18 GPIO.96->KBR5 mode 3 -DO- */
+ __raw_writeb(0x3, base+0x10e);
+ /* PIN = N19 GPIO.98->KBC6 mode 3 -DO- */
+ __raw_writeb(0x3, base+0x110);
+ /* PIN = J15 MDOC_nDMAREQ */
+ /* PIN = H19 GPIO.100->KBC2 mode 3 -DO- */
+ __raw_writeb(0x3, base+0x114);
+ /* PIN = W13, V12, P13, R13, W19, W16 ... */
+ /* PIN = AA17 sys_clkreq->bt_clk_req mode 0 */
+ } else if (cpu == CPU_2422) {
+ /* PIN = B3, GPIO.0->MMC_CD, mode 3, set above */
+ /* PIN = B13, GPIO.38->wlan_int, mode 3, (pun?)*/
+ /* Pin = Y11 VLNQ */
+ /* Pin = AA4 VLNQ */
+ /* Pin = AA6 VLNQ */
+ /* Pin = AA8 VLNQ */
+ /* Pin = AA10 VLNQ */
+ /* Pin = AA12 VLNQ */
+ /* PIN = M18 GPIO.96->KBR5 mode 3 -DO- */
+ __raw_writeb(0x3, base+0x10e);
+ /* PIN = N19 GPIO.98->KBC6 mode 3 -DO- */
+ __raw_writeb(0x3, base+0x110);
+ /* PIN = J15 MDOC_nDMAREQ */
+ /* PIN = H19 GPIO.100->KBC2 mode 3 -DO- */
+ __raw_writeb(0x3, base+0x114);
+ /* PIN = W13, V12, P13, R13, W19, W16 ... */
+ /* PIN = AA17 sys_clkreq->bt_clk_req mode 0 */
+ }
+ }
+}
--- /dev/null
+/*
+ * (C) Copyright 2004
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/omap2420.h>
+#include <asm/io.h>
+#include <asm/arch/bits.h>
+#include <asm/arch/mem.h> /* get mem tables */
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/sys_info.h>
+#include <i2c.h>
+
+/**************************************************************************
+ * get_prod_id() - get id info from chips
+ ***************************************************************************/
+static u32 get_prod_id(void)
+{
+ u32 p;
+ p = __raw_readl(PRODUCTION_ID); /* get production ID */
+ return((p & CPU_242X_PID_MASK) >> 16);
+}
+
+/**************************************************************************
+ * get_cpu_type() - low level get cpu type
+ * - no C globals yet.
+ * - just looking to say if this is a 2422 or 2420 or ...
+ * - to start with we will look at switch settings..
+ * - 2422 id's same as 2420 for ES1 will rely on H4 board characteristics
+ * (mux for 2420, non-mux for 2422).
+ ***************************************************************************/
+u32 get_cpu_type(void)
+{
+ u32 v;
+
+ switch(get_prod_id()){
+ case 1:;/* 2420 */
+ case 2: return(CPU_2420); break; /* 2420 pop */
+ case 4: return(CPU_2422); break;
+ case 8: return(CPU_2423); break;
+ default: break; /* early 2420/2422's unmarked */
+ }
+
+ v = __raw_readl(TAP_IDCODE_REG);
+ v &= CPU_24XX_ID_MASK;
+ if (v == CPU_2420_CHIPID) { /* currently 2420 and 2422 have same id */
+ if (is_gpmc_muxed() == GPMC_MUXED) /* if mux'ed */
+ return(CPU_2420);
+ else
+ return(CPU_2422);
+ } else
+ return(CPU_2420); /* don't know, say 2420 */
+}
+
+/******************************************
+ * get_cpu_rev(void) - extract version info
+ ******************************************/
+u32 get_cpu_rev(void)
+{
+ u32 v;
+ v = __raw_readl(TAP_IDCODE_REG);
+ v = v >> 28;
+ return(v+1); /* currently 2422 and 2420 match up */
+}
+/****************************************************
+ * is_mem_sdr() - return 1 if mem type in use is SDR
+ ****************************************************/
+u32 is_mem_sdr(void)
+{
+ volatile u32 *burst = (volatile u32 *)(SDRC_MR_0+SDRC_CS0_OSET);
+ if(*burst == H4_2420_SDRC_MR_0_SDR)
+ return(1);
+ return(0);
+}
+
+/***********************************************************
+ * get_mem_type() - identify type of mDDR part used.
+ * 2422 uses stacked DDR, 2 parts CS0/CS1.
+ * 2420 may have 1 or 2, no good way to know...only init 1...
+ * when eeprom data is up we can select 1 more.
+ *************************************************************/
+u32 get_mem_type(void)
+{
+ u32 cpu, sdr = is_mem_sdr();
+
+ cpu = get_cpu_type();
+ if (cpu == CPU_2422 || cpu == CPU_2423)
+ return(DDR_STACKED);
+
+ if(get_prod_id() == 0x2)
+ return(XDR_POP);
+
+ if (get_board_type() == BOARD_H4_MENELAUS)
+ if(sdr)
+ return(SDR_DISCRETE);
+ else
+ return(DDR_COMBO);
+ else
+ if(sdr) /* SDP + SDR kit */
+ return(SDR_DISCRETE);
+ else
+ return(DDR_DISCRETE); /* origional SDP */
+}
+
+/***********************************************************************
+ * get_cs0_size() - get size of chip select 0/1
+ ************************************************************************/
+u32 get_sdr_cs_size(u32 offset)
+{
+ u32 size;
+ size = __raw_readl(SDRC_MCFG_0+offset) >> 8; /* get ram size field */
+ size &= 0x2FF; /* remove unwanted bits */
+ size *= SZ_2M; /* find size in MB */
+ return(size);
+}
+
+/***********************************************************************
+ * get_board_type() - get board type based on current production stats.
+ * --- NOTE: 2 I2C EEPROMs will someday be populated with proper info.
+ * when they are available we can get info from there. This should
+ * be correct of all known boards up until today.
+ ************************************************************************/
+u32 get_board_type(void)
+{
+ if (i2c_probe(I2C_MENELAUS) == 0)
+ return(BOARD_H4_MENELAUS);
+ else
+ return(BOARD_H4_SDP);
+}
+
+/******************************************************************
+ * get_sysboot_value() - get init word settings (dip switch on h4)
+ ******************************************************************/
+inline u32 get_sysboot_value(void)
+{
+ return(0x00000FFF & __raw_readl(CONTROL_STATUS));
+}
+
+/***************************************************************************
+ * get_gpmc0_base() - Return current address hardware will be
+ * fetching from. The below effectively gives what is correct, its a bit
+ * mis-leading compared to the TRM. For the most general case the mask
+ * needs to be also taken into account this does work in practice.
+ * - for u-boot we currently map:
+ * -- 0 to nothing,
+ * -- 4 to flash
+ * -- 8 to enent
+ * -- c to wifi
+ ****************************************************************************/
+u32 get_gpmc0_base(void)
+{
+ u32 b;
+
+ b = __raw_readl(GPMC_CONFIG7_0);
+ b &= 0x1F; /* keep base [5:0] */
+ b = b << 24; /* ret 0x0b000000 */
+ return(b);
+}
+
+/*****************************************************************
+ * is_gpmc_muxed() - tells if address/data lines are multiplexed
+ *****************************************************************/
+u32 is_gpmc_muxed(void)
+{
+ u32 mux;
+ mux = get_sysboot_value();
+ if ((mux & (BIT0 | BIT1 | BIT2 | BIT3)) == (BIT0 | BIT2 | BIT3))
+ return(GPMC_MUXED); /* NAND Boot mode */
+ if (mux & BIT1) /* if mux'ed */
+ return(GPMC_MUXED);
+ else
+ return(GPMC_NONMUXED);
+}
+
+/************************************************************************
+ * get_gpmc0_type() - read sysboot lines to see type of memory attached
+ ************************************************************************/
+u32 get_gpmc0_type(void)
+{
+ u32 type;
+ type = get_sysboot_value();
+ if ((type & (BIT3|BIT2)) == (BIT3|BIT2))
+ return(TYPE_NAND);
+ else
+ return(TYPE_NOR);
+}
+
+/*******************************************************************
+ * get_gpmc0_width() - See if bus is in x8 or x16 (mainly for nand)
+ *******************************************************************/
+u32 get_gpmc0_width(void)
+{
+ u32 width;
+ width = get_sysboot_value();
+ if ((width & 0xF) == (BIT3|BIT2))
+ return(WIDTH_8BIT);
+ else
+ return(WIDTH_16BIT);
+}
+
+/*********************************************************************
+ * wait_on_value() - common routine to allow waiting for changes in
+ * volatile regs.
+ *********************************************************************/
+u32 wait_on_value(u32 read_bit_mask, u32 match_value, u32 read_addr, u32 bound)
+{
+ u32 i = 0, val;
+ do {
+ ++i;
+ val = __raw_readl(read_addr) & read_bit_mask;
+ if (val == match_value)
+ return(1);
+ if (i==bound)
+ return(0);
+ } while (1);
+}
+
+/*********************************************************************
+ * display_board_info() - print banner with board info.
+ *********************************************************************/
+void display_board_info(u32 btype)
+{
+ char cpu_2420[] = "2420"; /* cpu type */
+ char cpu_2422[] = "2422";
+ char cpu_2423[] = "2423";
+ char db_men[] = "Menelaus"; /* board type */
+ char db_ip[] = "IP";
+ char mem_sdr[] = "mSDR"; /* memory type */
+ char mem_ddr[] = "mDDR";
+ char t_tst[] = "TST"; /* security level */
+ char t_emu[] = "EMU";
+ char t_hs[] = "HS";
+ char t_gp[] = "GP";
+ char unk[] = "?";
+
+ char *cpu_s, *db_s, *mem_s, *sec_s;
+ u32 cpu, rev, sec;
+
+ rev = get_cpu_rev();
+ cpu = get_cpu_type();
+ sec = get_device_type();
+
+ if(is_mem_sdr())
+ mem_s = mem_sdr;
+ else
+ mem_s = mem_ddr;
+
+ if(cpu == CPU_2423)
+ cpu_s = cpu_2423;
+ else if (cpu == CPU_2422)
+ cpu_s = cpu_2422;
+ else
+ cpu_s = cpu_2420;
+
+ if(btype == BOARD_H4_MENELAUS)
+ db_s = db_men;
+ else
+ db_s = db_ip;
+
+ switch(sec){
+ case TST_DEVICE: sec_s = t_tst; break;
+ case EMU_DEVICE: sec_s = t_emu; break;
+ case HS_DEVICE: sec_s = t_hs; break;
+ case GP_DEVICE: sec_s = t_gp; break;
+ default: sec_s = unk;
+ }
+
+ printf("OMAP%s-%s revision %d\n", cpu_s, sec_s, rev-1);
+ printf("TI H4 SDP Base Board + %s Daughter Board + %s \n", db_s, mem_s);
+}
+
+/*************************************************************************
+ * get_board_rev() - setup to pass kernel board revision information
+ * 0 = 242x IP platform (first 2xx boards)
+ * 1 = 242x Menelaus platfrom.
+ *************************************************************************/
+u32 get_board_rev(void)
+{
+ u32 rev = 0;
+ u32 btype = get_board_type();
+
+ if (btype == BOARD_H4_MENELAUS){
+ rev = 1;
+ }
+ return(rev);
+}
+
+/********************************************************
+ * get_base(); get upper addr of current execution
+ *******************************************************/
+u32 get_base(void)
+{
+ u32 val;
+ __asm__ __volatile__("mov %0, pc \n" : "=r" (val) : : "memory");
+ val &= 0xF0000000;
+ val >>= 28;
+ return(val);
+}
+
+/********************************************************
+ * get_base2(); get 2upper addr of current execution
+ *******************************************************/
+u32 get_base2(void)
+{
+ u32 val;
+ __asm__ __volatile__("mov %0, pc \n" : "=r" (val) : : "memory");
+ val &= 0xFF000000;
+ val >>= 24;
+ return(val);
+}
+
+/********************************************************
+ * running_in_flash() - tell if currently running in
+ * flash.
+ *******************************************************/
+u32 running_in_flash(void)
+{
+ if (get_base() < 4)
+ return(1); /* in flash */
+ return(0); /* running in SRAM or SDRAM */
+}
+
+/********************************************************
+ * running_in_sram() - tell if currently running in
+ * sram.
+ *******************************************************/
+u32 running_in_sram(void)
+{
+ if (get_base() == 4)
+ return(1); /* in SRAM */
+ return(0); /* running in FLASH or SDRAM */
+}
+/********************************************************
+ * running_in_sdram() - tell if currently running in
+ * flash.
+ *******************************************************/
+u32 running_in_sdram(void)
+{
+ if (get_base() > 4)
+ return(1); /* in sdram */
+ return(0); /* running in SRAM or FLASH */
+}
+
+/*************************************************************
+ * running_from_internal_boot() - am I a signed NOR image.
+ *************************************************************/
+u32 running_from_internal_boot(void)
+{
+ u32 v, base;
+
+ v = get_sysboot_value() & BIT3;
+ base = get_base2();
+ /* if running at mask rom flash address and
+ * sysboot3 says this was an internal boot
+ */
+ if ((base == 0x08) && v)
+ return(1);
+ else
+ return(0);
+}
+
+/*************************************************************
+ * get_device_type(): tell if GP/HS/EMU/TST
+ *************************************************************/
+u32 get_device_type(void)
+{
+ int mode;
+ mode = __raw_readl(CONTROL_STATUS) & (BIT10|BIT9|BIT8);
+ return(mode >>= 8);
+}
--- /dev/null
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := omap5912osk.o
+SOBJS := lowlevel_init.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+#
+# (C) Copyright 2002-2004
+# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
+# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+#
+# (C) Copyright 2003
+# Texas Instruments, <www.ti.com>
+# Kshitij Gupta <Kshitij@ti.com>
+#
+# (C) Copyright 2004
+# Texas Instruments, <www.ti.com>
+# Rishi Bhattacharya <rishi@ti.com>
+#
+# TI OSK board with OMAP5912 (ARM925EJS) cpu
+# see http://www.ti.com/ for more information on Texas Instruments
+#
+# OSK has 1 bank of 256 MB SDRAM
+# Physical Address:
+# 1000'0000 to 2000'0000
+#
+#
+# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000
+# (mem base + reserved)
+#
+# we load ourself to 1108'0000
+#
+#
+
+
+TEXT_BASE = 0x11080000
--- /dev/null
+/*
+ * Board specific setup info
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
+ *
+ * Modified for OMAP 5912 OSK board by Rishi Bhattacharya, Apr 2004
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+
+#if defined(CONFIG_OMAP1610)
+#include <./configs/omap1510.h>
+#endif
+
+
+_TEXT_BASE:
+ .word TEXT_BASE /* sdram load addr from config.mk */
+
+.globl lowlevel_init
+lowlevel_init:
+
+ /*------------------------------------------------------*
+ * Ensure i-cache is enabled *
+ * To configure TC regs without fetching instruction *
+ *------------------------------------------------------*/
+ mrc p15, 0, r0, c1, c0
+ orr r0, r0, #0x1000
+ mcr p15, 0, r0, c1, c0
+
+ /*------------------------------------------------------*
+ *mask all IRQs by setting all bits in the INTMR default*
+ *------------------------------------------------------*/
+ mov r1, #0xffffffff
+ ldr r0, =REG_IHL1_MIR
+ str r1, [r0]
+ ldr r0, =REG_IHL2_MIR
+ str r1, [r0]
+
+ /*------------------------------------------------------*
+ * Set up ARM CLM registers (IDLECT1) *
+ *------------------------------------------------------*/
+ ldr r0, REG_ARM_IDLECT1
+ ldr r1, VAL_ARM_IDLECT1
+ str r1, [r0]
+
+ /*------------------------------------------------------*
+ * Set up ARM CLM registers (IDLECT2) *
+ *------------------------------------------------------*/
+ ldr r0, REG_ARM_IDLECT2
+ ldr r1, VAL_ARM_IDLECT2
+ str r1, [r0]
+
+ /*------------------------------------------------------*
+ * Set up ARM CLM registers (IDLECT3) *
+ *------------------------------------------------------*/
+ ldr r0, REG_ARM_IDLECT3
+ ldr r1, VAL_ARM_IDLECT3
+ str r1, [r0]
+
+ mov r1, #0x01 /* PER_EN bit */
+ ldr r0, REG_ARM_RSTCT2
+ strh r1, [r0] /* CLKM; Peripheral reset. */
+
+ /* Set CLKM to Sync-Scalable */
+ mov r1, #0x1000
+ ldr r0, REG_ARM_SYSST
+
+ mov r2, #0
+1: cmp r2, #1
+ streqh r1, [r0]
+ add r2, r2, #1
+ cmp r2, #0x100 /* wait for any bubbles to finish */
+ bne 1b
+
+ ldr r1, VAL_ARM_CKCTL
+ ldr r0, REG_ARM_CKCTL
+ strh r1, [r0]
+
+ /* a few nops to let settle */
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+
+ /* setup DPLL 1 */
+ /* Ramp up the clock to 96Mhz */
+ ldr r1, VAL_DPLL1_CTL
+ ldr r0, REG_DPLL1_CTL
+ strh r1, [r0]
+ ands r1, r1, #0x10 /* Check if PLL is enabled. */
+ beq lock_end /* Do not look for lock if BYPASS selected */
+2:
+ ldrh r1, [r0]
+ ands r1, r1, #0x01 /* Check the LOCK bit.*/
+ beq 2b /* loop until bit goes hi. */
+lock_end:
+
+ /*------------------------------------------------------*
+ * Turn off the watchdog during init... *
+ *------------------------------------------------------*/
+ ldr r0, REG_WATCHDOG
+ ldr r1, WATCHDOG_VAL1
+ str r1, [r0]
+ ldr r1, WATCHDOG_VAL2
+ str r1, [r0]
+ ldr r0, REG_WSPRDOG
+ ldr r1, WSPRDOG_VAL1
+ str r1, [r0]
+ ldr r0, REG_WWPSDOG
+
+watch1Wait:
+ ldr r1, [r0]
+ tst r1, #0x10
+ bne watch1Wait
+
+ ldr r0, REG_WSPRDOG
+ ldr r1, WSPRDOG_VAL2
+ str r1, [r0]
+ ldr r0, REG_WWPSDOG
+watch2Wait:
+ ldr r1, [r0]
+ tst r1, #0x10
+ bne watch2Wait
+
+ /* Set memory timings corresponding to the new clock speed */
+ ldr r3, VAL_SDRAM_CONFIG_SDF0
+
+ /* Check execution location to determine current execution location
+ * and branch to appropriate initialization code.
+ */
+ mov r0, #0x10000000 /* Load physical SDRAM base. */
+ mov r1, pc /* Get current execution location. */
+ cmp r1, r0 /* Compare. */
+ bge skip_sdram /* Skip over EMIF-fast initialization if running from SDRAM. */
+
+ /* identify the device revision, -- TMX or TMP(TMS) */
+ ldr r0, REG_DEVICE_ID
+ ldr r1, [r0]
+
+ ldr r0, VAL_DEVICE_ID_TMP
+ mov r1, r1, lsl #15
+ mov r1, r1, lsr #16
+ cmp r0, r1
+ bne skip_TMP_Patch
+
+ /* Enable TMP/TMS device new features */
+ mov r0, #1
+ ldr r1, REG_TC_EMIFF_DOUBLER
+ str r0, [r1]
+
+ /* Enable new ac parameters */
+ mov r0, #0x0b
+ ldr r1, REG_SDRAM_CONFIG2
+ str r0, [r1]
+
+ ldr r3, VAL_SDRAM_CONFIG_SDF1
+
+skip_TMP_Patch:
+
+ /*
+ * Delay for SDRAM initialization.
+ */
+ mov r0, #0x1800 /* value should be checked */
+3:
+ subs r0, r0, #0x1 /* Decrement count */
+ bne 3b
+
+ /*
+ * Set SDRAM control values. Disable refresh before MRS command.
+ */
+
+ /* mobile ddr operation */
+ ldr r0, REG_SDRAM_OPERATION
+ mov r2, #07
+ str r2, [r0]
+
+ /* config register */
+ ldr r0, REG_SDRAM_CONFIG
+ str r3, [r0]
+
+ /* manual command register */
+ ldr r0, REG_SDRAM_MANUAL_CMD
+
+ /* issue set cke high */
+ mov r1, #CMD_SDRAM_CKE_SET_HIGH
+ str r1, [r0]
+
+ /* issue nop */
+ mov r1, #CMD_SDRAM_NOP
+ str r1, [r0]
+
+ mov r2, #0x0100
+waitMDDR1:
+ subs r2, r2, #1
+ bne waitMDDR1 /* delay loop */
+
+ /* issue precharge */
+ mov r1, #CMD_SDRAM_PRECHARGE
+ str r1, [r0]
+
+ /* issue autorefresh x 2 */
+ mov r1, #CMD_SDRAM_AUTOREFRESH
+ str r1, [r0]
+ str r1, [r0]
+
+ /* mrs register ddr mobile */
+ ldr r0, REG_SDRAM_MRS
+ mov r1, #0x33
+ str r1, [r0]
+
+ /* emrs1 low-power register */
+ ldr r0, REG_SDRAM_EMRS1
+ /* self refresh on all banks */
+ mov r1, #0
+ str r1, [r0]
+
+ ldr r0, REG_DLL_URD_CONTROL
+ ldr r1, DLL_URD_CONTROL_VAL
+ str r1, [r0]
+
+ ldr r0, REG_DLL_LRD_CONTROL
+ ldr r1, DLL_LRD_CONTROL_VAL
+ str r1, [r0]
+
+ ldr r0, REG_DLL_WRT_CONTROL
+ ldr r1, DLL_WRT_CONTROL_VAL
+ str r1, [r0]
+
+ /* delay loop */
+ mov r0, #0x0100
+waitMDDR2:
+ subs r0, r0, #1
+ bne waitMDDR2
+
+ /*
+ * Delay for SDRAM initialization.
+ */
+ mov r0, #0x1800
+4:
+ subs r0, r0, #1 /* Decrement count. */
+ bne 4b
+ b common_tc
+
+skip_sdram:
+ ldr r0, REG_SDRAM_CONFIG
+ str r3, [r0]
+
+common_tc:
+ /* slow interface */
+ ldr r1, VAL_TC_EMIFS_CS0_CONFIG
+ ldr r0, REG_TC_EMIFS_CS0_CONFIG
+ str r1, [r0] /* Chip Select 0 */
+
+ ldr r1, VAL_TC_EMIFS_CS1_CONFIG
+ ldr r0, REG_TC_EMIFS_CS1_CONFIG
+ str r1, [r0] /* Chip Select 1 */
+
+ ldr r1, VAL_TC_EMIFS_CS3_CONFIG
+ ldr r0, REG_TC_EMIFS_CS3_CONFIG
+ str r1, [r0] /* Chip Select 3 */
+
+ ldr r1, VAL_TC_EMIFS_DWS
+ ldr r0, REG_TC_EMIFS_DWS
+ str r1, [r0] /* Enable EMIFS.RDY for CS1 (ether) */
+
+#ifdef CONFIG_H2_OMAP1610
+ /* inserting additional 2 clock cycle hold time for LAN */
+ ldr r0, REG_TC_EMIFS_CS1_ADVANCED
+ ldr r1, VAL_TC_EMIFS_CS1_ADVANCED
+ str r1, [r0]
+#endif
+ /* Start MPU Timer 1 */
+ ldr r0, REG_MPU_LOAD_TIMER
+ ldr r1, VAL_MPU_LOAD_TIMER
+ str r1, [r0]
+
+ ldr r0, REG_MPU_CNTL_TIMER
+ ldr r1, VAL_MPU_CNTL_TIMER
+ str r1, [r0]
+
+ /* back to arch calling code */
+ mov pc, lr
+
+ /* the literal pools origin */
+ .ltorg
+
+REG_DEVICE_ID: /* 32 bits */
+ .word 0xfffe2004
+REG_TC_EMIFS_CONFIG:
+ .word 0xfffecc0c
+REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */
+ .word 0xfffecc10
+REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */
+ .word 0xfffecc14
+REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */
+ .word 0xfffecc18
+REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */
+ .word 0xfffecc1c
+REG_TC_EMIFS_DWS: /* 32 bits */
+ .word 0xfffecc40
+#ifdef CONFIG_H2_OMAP1610
+REG_TC_EMIFS_CS1_ADVANCED: /* 32 bits */
+ .word 0xfffecc54
+#endif
+
+/* MPU clock/reset/power mode control registers */
+REG_ARM_CKCTL: /* 16 bits */
+ .word 0xfffece00
+REG_ARM_IDLECT3: /* 16 bits */
+ .word 0xfffece24
+REG_ARM_IDLECT2: /* 16 bits */
+ .word 0xfffece08
+REG_ARM_IDLECT1: /* 16 bits */
+ .word 0xfffece04
+REG_ARM_RSTCT2: /* 16 bits */
+ .word 0xfffece14
+REG_ARM_SYSST: /* 16 bits */
+ .word 0xfffece18
+
+/* DPLL control registers */
+REG_DPLL1_CTL: /* 16 bits */
+ .word 0xfffecf00
+
+/* Watch Dog register */
+/* secure watchdog stop */
+REG_WSPRDOG:
+ .word 0xfffeb048
+/* watchdog write pending */
+REG_WWPSDOG:
+ .word 0xfffeb034
+
+WSPRDOG_VAL1:
+ .word 0x0000aaaa
+WSPRDOG_VAL2:
+ .word 0x00005555
+
+/* SDRAM config is: auto refresh enabled, 16 bit 4 bank,
+ counter @8192 rows, 10 ns, 8 burst */
+REG_SDRAM_CONFIG:
+ .word 0xfffecc20
+REG_SDRAM_CONFIG2:
+ .word 0xfffecc3c
+REG_TC_EMIFF_DOUBLER: /* 32 bits */
+ .word 0xfffecc60
+
+/* Operation register */
+REG_SDRAM_OPERATION:
+ .word 0xfffecc80
+
+/* Manual command register */
+REG_SDRAM_MANUAL_CMD:
+ .word 0xfffecc84
+
+/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */
+REG_SDRAM_MRS:
+ .word 0xfffecc70
+
+/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */
+REG_SDRAM_EMRS1:
+ .word 0xfffecc78
+
+/* WRT DLL register */
+REG_DLL_WRT_CONTROL:
+ .word 0xfffecc68
+DLL_WRT_CONTROL_VAL:
+ .word 0x03f00002 /* Phase of 72deg, write offset +31 */
+
+/* URD DLL register */
+REG_DLL_URD_CONTROL:
+ .word 0xfffeccc0
+DLL_URD_CONTROL_VAL:
+ .word 0x00800002 /* Phase of 72deg, read offset +31 */
+
+/* LRD DLL register */
+REG_DLL_LRD_CONTROL:
+ .word 0xfffecccc
+DLL_LRD_CONTROL_VAL:
+ .word 0x00800002 /* read offset +31 */
+
+REG_WATCHDOG:
+ .word 0xfffec808
+WATCHDOG_VAL1:
+ .word 0x000000f5
+WATCHDOG_VAL2:
+ .word 0x000000a0
+
+REG_MPU_LOAD_TIMER:
+ .word 0xfffec504
+REG_MPU_CNTL_TIMER:
+ .word 0xfffec500
+VAL_MPU_LOAD_TIMER:
+ .word 0xffffffff
+VAL_MPU_CNTL_TIMER:
+ .word 0xffffffa1
+
+/* 96 MHz Samsung Mobile DDR */
+/* Original setting for TMX device */
+VAL_SDRAM_CONFIG_SDF0:
+ .word 0x0014e6fe
+
+/* NEW_SYS_FREQ mode (valid only TMP/TMS devices) */
+VAL_SDRAM_CONFIG_SDF1:
+ .word 0x0114e6fe
+
+VAL_ARM_CKCTL:
+ .word 0x2000 /* was: 0x3000, now use CLK_REF for timer input */
+VAL_DPLL1_CTL:
+ .word 0x2830
+
+#ifdef CONFIG_OSK_OMAP5912
+VAL_TC_EMIFS_CS0_CONFIG:
+ .word 0x002130b0
+VAL_TC_EMIFS_CS1_CONFIG:
+ .word 0x00001133
+VAL_TC_EMIFS_CS2_CONFIG:
+ .word 0x000055f0
+VAL_TC_EMIFS_CS3_CONFIG:
+ .word 0x88013141
+VAL_TC_EMIFS_DWS: /* Enable EMIFS.RDY for CS1 access (ether) */
+ .word 0x000000c0
+VAL_DEVICE_ID_TMP: /* TMP/TMS=0xb65f, TMX=0xb58c */
+ .word 0xb65f
+#endif
+
+#ifdef CONFIG_H2_OMAP1610
+VAL_TC_EMIFS_CS0_CONFIG:
+ .word 0x00203331
+VAL_TC_EMIFS_CS1_CONFIG:
+ .word 0x8180fff3
+VAL_TC_EMIFS_CS2_CONFIG:
+ .word 0xf800f22a
+VAL_TC_EMIFS_CS3_CONFIG:
+ .word 0x88013141
+VAL_TC_EMIFS_CS1_ADVANCED:
+ .word 0x00000022
+#endif
+
+VAL_ARM_IDLECT1:
+ .word 0x00000400
+VAL_ARM_IDLECT2:
+ .word 0x00000886
+VAL_ARM_IDLECT3:
+ .word 0x00000015
+
+/* command values */
+.equ CMD_SDRAM_NOP, 0x00000000
+.equ CMD_SDRAM_PRECHARGE, 0x00000001
+.equ CMD_SDRAM_AUTOREFRESH, 0x00000002
+.equ CMD_SDRAM_CKE_SET_HIGH, 0x00000007
--- /dev/null
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * (C) Copyright 2004
+ * Texas Instruments, <www.ti.com>
+ * Rishi Bhattacharya <rishi@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#if defined(CONFIG_OMAP1610)
+#include <./configs/omap1510.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void flash__init (void);
+void ether__init (void);
+void set_muxconf_regs (void);
+void peripheral_power_enable (void);
+
+#define COMP_MODE_ENABLE ((unsigned int)0x0000EAEF)
+
+static inline void delay (unsigned long loops)
+{
+ __asm__ volatile ("1:\n"
+ "subs %0, %1, #1\n"
+ "bne 1b":"=r" (loops):"0" (loops));
+}
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP_OSK;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = 0x10000100;
+
+ /* Configure MUX settings */
+ set_muxconf_regs ();
+ peripheral_power_enable ();
+
+/* this speeds up your boot a quite a bit. However to make it
+ * work, you need make sure your kernel startup flush bug is fixed.
+ * ... rkw ...
+ */
+ icache_enable ();
+
+ flash__init ();
+ ether__init ();
+ return 0;
+}
+
+
+int misc_init_r (void)
+{
+ /* currently empty */
+ return (0);
+}
+
+/******************************
+ Routine:
+ Description:
+******************************/
+void flash__init (void)
+{
+#define EMIFS_GlB_Config_REG 0xfffecc0c
+ unsigned int regval;
+ regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG);
+ /* Turn off write protection for flash devices. */
+ regval = regval | 0x0001;
+ *((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval;
+}
+/*************************************************************
+ Routine:ether__init
+ Description: take the Ethernet controller out of reset and wait
+ for the EEPROM load to complete.
+*************************************************************/
+void ether__init (void)
+{
+#define ETH_CONTROL_REG 0x0480000b
+ int i;
+
+ *((volatile unsigned short *) 0xfffece08) = 0x03FF;
+ *((volatile unsigned short *) 0xfffb3824) = 0x8000;
+ *((volatile unsigned short *) 0xfffb3830) = 0x0000;
+ *((volatile unsigned short *) 0xfffb3834) = 0x0009;
+ *((volatile unsigned short *) 0xfffb3838) = 0x0009;
+ *((volatile unsigned short *) 0xfffb3818) = 0x0002;
+ *((volatile unsigned short *) 0xfffb382C) = 0x0048;
+ *((volatile unsigned short *) 0xfffb3824) = 0x8603;
+ udelay (3);
+ for (i=0;i<2000;i++);
+ *((volatile unsigned short *) 0xfffb381C) = 0x6610;
+ udelay (30);
+ for (i=0;i<10000;i++);
+
+ *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
+ udelay (3);
+
+
+}
+
+/******************************
+ Routine:
+ Description:
+******************************/
+int dram_init (void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+ return 0;
+}
+
+/******************************************************
+ Routine: set_muxconf_regs
+ Description: Setting up the configuration Mux registers
+ specific to the hardware
+*******************************************************/
+void set_muxconf_regs (void)
+{
+ volatile unsigned int *MuxConfReg;
+ /* set each registers to its reset value; */
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
+ /* setup for UART1 */
+ *MuxConfReg &= ~(0x02000000); /* bit 25 */
+ /* setup for UART2 */
+ *MuxConfReg &= ~(0x01000000); /* bit 24 */
+ /* Disable Uwire CS Hi-Z */
+ *MuxConfReg |= 0x08000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_3);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_4);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_5);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_6);
+ /*setup mux for UART3 */
+ *MuxConfReg |= 0x00000001; /* bit3, 1, 0 (mux0 5,5,26) */
+ *MuxConfReg &= ~0x0000003e;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_7);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_8);
+ /* Disable Uwire CS Hi-Z */
+ *MuxConfReg |= 0x00001200; /*bit 9 for CS0 12 for CS3 */
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_9);
+ /* Need to turn on bits 21 and 12 in FUNC_MUX_CTRL_9 so the */
+ /* hardware will actually use TX and RTS based on bit 25 in */
+ /* FUNC_MUX_CTRL_0. I told you this thing was screwy! */
+ *MuxConfReg |= 0x00201000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_A);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_B);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_C);
+ /* setup for UART2 */
+ /* Need to turn on bits 27 and 24 in FUNC_MUX_CTRL_C so the */
+ /* hardware will actually use TX and RTS based on bit 24 in */
+ /* FUNC_MUX_CTRL_0. */
+ *MuxConfReg |= 0x09000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_D);
+ *MuxConfReg |= 0x00000020;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_0);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_1);
+ *MuxConfReg = 0x00000000;
+ /* mux setup for SD/MMC driver */
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_2);
+ *MuxConfReg &= 0xFFFE0FFF;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_3);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
+ /* bit 13 for MMC2 XOR_CLK */
+ *MuxConfReg &= ~(0x00002000);
+ /* bit 29 for UART 1 */
+ *MuxConfReg &= ~(0x00002000);
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
+ /* Configure for USB. Turn on VBUS_CTRL and VBUS_MODE. */
+ *MuxConfReg |= 0x000C0000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int)USB_TRANSCEIVER_CTRL);
+ *MuxConfReg &= ~(0x00000070);
+ *MuxConfReg &= ~(0x00000008);
+ *MuxConfReg |= 0x00000003;
+ *MuxConfReg |= 0x00000180;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
+ /* bit 17, software controls VBUS */
+ *MuxConfReg &= ~(0x00020000);
+ /* Enable USB 48 and 12M clocks */
+ *MuxConfReg |= 0x00000200;
+ *MuxConfReg &= ~(0x00000180);
+ /*2.75V for MMCSDIO1 */
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) VOLTAGE_CTRL_0);
+ *MuxConfReg = 0x00001FE7;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PU_PD_SEL_0);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PU_PD_SEL_1);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PU_PD_SEL_3);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PU_PD_SEL_4);
+ *MuxConfReg = 0x00000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_4);
+ *MuxConfReg = 0x00000000;
+ /* Turn on UART2 48 MHZ clock */
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
+ *MuxConfReg |= 0x40000000;
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) USB_OTG_CTRL);
+ /* setup for USB VBus detection OMAP161x */
+ *MuxConfReg |= 0x00040000; /* bit 18 */
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
+ /* PullUps for SD/MMC driver */
+ *MuxConfReg |= ~(0xFFFE0FFF);
+ MuxConfReg =
+ (volatile unsigned int *) ((unsigned int)COMP_MODE_CTRL_0);
+ *MuxConfReg = COMP_MODE_ENABLE;
+}
+
+/******************************************************
+ Routine: peripheral_power_enable
+ Description: Enable the power for UART1
+*******************************************************/
+void peripheral_power_enable (void)
+{
+#define UART1_48MHZ_ENABLE ((unsigned short)0x0200)
+#define SW_CLOCK_REQUEST ((volatile unsigned short *)0xFFFE0834)
+
+ *SW_CLOCK_REQUEST |= UART1_48MHZ_ENABLE;
+}
+
+/*
+ * Check Board Identity
+ */
+int checkboard(void)
+{
+ char *s = getenv("serial#");
+
+ puts("Board: OSK5912");
+
+ if (s != NULL) {
+ puts(", serial# ");
+ puts(s);
+ }
+ putc('\n');
+
+ return (0);
+}
--- /dev/null
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := omap730p2.o flash.o
+SOBJS := lowlevel_init.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+#
+# (C) Copyright 2002
+# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
+# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+#
+# (C) Copyright 2003
+# Texas Instruments, <www.ti.com>
+# Kshitij Gupta <Kshitij@ti.com>
+#
+# TI Perseus 2 board with OMAP720 (ARM925EJS) cpu
+# see http://www.ti.com/ for more information on Texas Instruments
+#
+# Innovator has 1 bank of 256 MB SDRAM
+# Physical Address:
+# 1000'0000 to 2000'0000
+#
+#
+# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000
+# (mem base + reserved)
+#
+# we load ourself to 1108'0000
+#
+#
+
+TEXT_BASE = 0x11080000
--- /dev/null
+/*
+ * (C) Copyright 2001
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <linux/byteorder/swab.h>
+
+#define PHYS_FLASH_SECT_SIZE 0x00020000 /* 256 KB sectors (x2) */
+flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
+
+/* Board support for 1 or 2 flash devices */
+#undef FLASH_PORT_WIDTH32
+#define FLASH_PORT_WIDTH16
+
+#ifdef FLASH_PORT_WIDTH16
+#define FLASH_PORT_WIDTH ushort
+#define FLASH_PORT_WIDTHV vu_short
+#define SWAP(x) __swab16(x)
+#else
+#define FLASH_PORT_WIDTH ulong
+#define FLASH_PORT_WIDTHV vu_long
+#define SWAP(x) __swab32(x)
+#endif
+
+#define FPW FLASH_PORT_WIDTH
+#define FPWV FLASH_PORT_WIDTHV
+
+#define mb() __asm__ __volatile__ ("" : : : "memory")
+
+
+/* Flash Organization Structure */
+typedef struct OrgDef {
+ unsigned int sector_number;
+ unsigned int sector_size;
+} OrgDef;
+
+
+/* Flash Organizations */
+OrgDef OrgIntel_28F256L18T[] = {
+ {4, 32 * 1024}, /* 4 * 32kBytes sectors */
+ {255, 128 * 1024}, /* 255 * 128kBytes sectors */
+};
+
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+unsigned long flash_init (void);
+static ulong flash_get_size (FPW * addr, flash_info_t * info);
+static int write_data (flash_info_t * info, ulong dest, FPW data);
+static void flash_get_offsets (ulong base, flash_info_t * info);
+void inline spin_wheel (void);
+void flash_print_info (flash_info_t * info);
+void flash_unprotect_sectors (FPWV * addr);
+int flash_erase (flash_info_t * info, int s_first, int s_last);
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+ int i;
+ ulong size = 0;
+ for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
+ switch (i) {
+ case 0:
+ flash_get_size ((FPW *) PHYS_FLASH_1, &flash_info[i]);
+ flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
+ break;
+ default:
+ panic ("configured too many flash banks!\n");
+ break;
+ }
+ size += flash_info[i].size;
+ }
+
+ /* Protect monitor and environment sectors
+ */
+ flash_protect (FLAG_PROTECT_SET,
+ CONFIG_SYS_FLASH_BASE,
+ CONFIG_SYS_FLASH_BASE + monitor_flash_len - 1, &flash_info[0]);
+
+ flash_protect (FLAG_PROTECT_SET,
+ CONFIG_ENV_ADDR,
+ CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]);
+
+ return size;
+}
+
+/*-----------------------------------------------------------------------
+ */
+static void flash_get_offsets (ulong base, flash_info_t * info)
+{
+ int i;
+ OrgDef *pOrgDef;
+
+ pOrgDef = OrgIntel_28F256L18T;
+ if (info->flash_id == FLASH_UNKNOWN) {
+ return;
+ }
+
+ if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
+ for (i = 0; i < info->sector_count; i++) {
+ if (i > 255) {
+ info->start[i] = base + (i * 0x8000);
+ info->protect[i] = 0;
+ } else {
+ info->start[i] = base +
+ (i * PHYS_FLASH_SECT_SIZE);
+ info->protect[i] = 0;
+ }
+ }
+ }
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info (flash_info_t * info)
+{
+ int i;
+
+ if (info->flash_id == FLASH_UNKNOWN) {
+ printf ("missing or unknown FLASH type\n");
+ return;
+ }
+
+ switch (info->flash_id & FLASH_VENDMASK) {
+ case FLASH_MAN_INTEL:
+ printf ("INTEL ");
+ break;
+ default:
+ printf ("Unknown Vendor ");
+ break;
+ }
+
+ switch (info->flash_id & FLASH_TYPEMASK) {
+ case FLASH_28F256L18T:
+ printf ("FLASH 28F256L18T\n");
+ break;
+ default:
+ printf ("Unknown Chip Type\n");
+ break;
+ }
+
+ printf (" Size: %ld MB in %d Sectors\n",
+ info->size >> 20, info->sector_count);
+
+ printf (" Sector Start Addresses:");
+ for (i = 0; i < info->sector_count; ++i) {
+ if ((i % 5) == 0)
+ printf ("\n ");
+ printf (" %08lX%s",
+ info->start[i], info->protect[i] ? " (RO)" : " ");
+ }
+ printf ("\n");
+ return;
+}
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+static ulong flash_get_size (FPW * addr, flash_info_t * info)
+{
+ volatile FPW value;
+
+ /* Write auto select command: read Manufacturer ID */
+ addr[0x5555] = (FPW) 0x00AA00AA;
+ addr[0x2AAA] = (FPW) 0x00550055;
+ addr[0x5555] = (FPW) 0x00900090;
+
+ mb ();
+ value = addr[0];
+
+ switch (value) {
+
+ case (FPW) INTEL_MANUFACT:
+ info->flash_id = FLASH_MAN_INTEL;
+ break;
+
+ default:
+ info->flash_id = FLASH_UNKNOWN;
+ info->sector_count = 0;
+ info->size = 0;
+ addr[0] = (FPW) 0x00FF00FF; /* restore read mode */
+ return (0); /* no or unknown flash */
+ }
+
+ mb ();
+ value = addr[1]; /* device ID */
+ switch (value) {
+
+ case (FPW) (INTEL_ID_28F256L18T):
+ info->flash_id += FLASH_28F256L18T;
+ info->sector_count = 259;
+ info->size = 0x02000000;
+ break; /* => 32 MB */
+
+ default:
+ info->flash_id = FLASH_UNKNOWN;
+ break;
+ }
+
+ if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
+ printf ("** ERROR: sector count %d > max (%d) **\n",
+ info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
+ info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
+ }
+
+ addr[0] = (FPW) 0x00FF00FF; /* restore read mode */
+
+ return (info->size);
+}
+
+
+/* unprotects a sector for write and erase
+ * on some intel parts, this unprotects the entire chip, but it
+ * wont hurt to call this additional times per sector...
+ */
+void flash_unprotect_sectors (FPWV * addr)
+{
+#define PD_FINTEL_WSMS_READY_MASK 0x0080
+
+ *addr = (FPW) 0x00500050; /* clear status register */
+
+ /* this sends the clear lock bit command */
+ *addr = (FPW) 0x00600060;
+ *addr = (FPW) 0x00D000D0;
+}
+
+
+/*-----------------------------------------------------------------------
+ */
+
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+ int flag, prot, sect;
+ ulong type, start, last;
+ int rcode = 0;
+
+ if ((s_first < 0) || (s_first > s_last)) {
+ if (info->flash_id == FLASH_UNKNOWN) {
+ printf ("- missing\n");
+ } else {
+ printf ("- no sectors to erase\n");
+ }
+ return 1;
+ }
+
+ type = (info->flash_id & FLASH_VENDMASK);
+ if ((type != FLASH_MAN_INTEL)) {
+ printf ("Can't erase unknown flash type %08lx - aborted\n",
+ info->flash_id);
+ return 1;
+ }
+
+ prot = 0;
+ for (sect = s_first; sect <= s_last; ++sect) {
+ if (info->protect[sect]) {
+ prot++;
+ }
+ }
+
+ if (prot) {
+ printf ("- Warning: %d protected sectors will not be erased!\n",
+ prot);
+ } else {
+ printf ("\n");
+ }
+
+
+ start = get_timer (0);
+ last = start;
+
+ /* Disable interrupts which might cause a timeout here */
+ flag = disable_interrupts ();
+
+ /* Start erase on unprotected sectors */
+ for (sect = s_first; sect <= s_last; sect++) {
+ if (info->protect[sect] == 0) { /* not protected */
+ FPWV *addr = (FPWV *) (info->start[sect]);
+ FPW status;
+
+ printf ("Erasing sector %2d ... ", sect);
+
+ flash_unprotect_sectors (addr);
+
+ /* arm simple, non interrupt dependent timer */
+ reset_timer_masked ();
+
+ *addr = (FPW) 0x00500050;/* clear status register */
+ *addr = (FPW) 0x00200020;/* erase setup */
+ *addr = (FPW) 0x00D000D0;/* erase confirm */
+
+ while (((status =
+ *addr) & (FPW) 0x00800080) !=
+ (FPW) 0x00800080) {
+ if (get_timer_masked () >
+ CONFIG_SYS_FLASH_ERASE_TOUT) {
+ printf ("Timeout\n");
+ /* suspend erase */
+ *addr = (FPW) 0x00B000B0;
+ /* reset to read mode */
+ *addr = (FPW) 0x00FF00FF;
+ rcode = 1;
+ break;
+ }
+ }
+
+ /* clear status register cmd. */
+ *addr = (FPW) 0x00500050;
+ *addr = (FPW) 0x00FF00FF;/* resest to read mode */
+ printf (" done\n");
+ }
+ }
+ return rcode;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ * 4 - Flash not identified
+ */
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+ ulong cp, wp;
+ FPW data;
+ int count, i, l, rc, port_width;
+
+ if (info->flash_id == FLASH_UNKNOWN) {
+ return 4;
+ }
+/* get lower word aligned address */
+#ifdef FLASH_PORT_WIDTH16
+ wp = (addr & ~1);
+ port_width = 2;
+#else
+ wp = (addr & ~3);
+ port_width = 4;
+#endif
+
+ /*
+ * handle unaligned start bytes
+ */
+ if ((l = addr - wp) != 0) {
+ data = 0;
+ for (i = 0, cp = wp; i < l; ++i, ++cp) {
+ data = (data << 8) | (*(uchar *) cp);
+ }
+ for (; i < port_width && cnt > 0; ++i) {
+ data = (data << 8) | *src++;
+ --cnt;
+ ++cp;
+ }
+ for (; cnt == 0 && i < port_width; ++i, ++cp) {
+ data = (data << 8) | (*(uchar *) cp);
+ }
+
+ if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+ return (rc);
+ }
+ wp += port_width;
+ }
+
+ /*
+ * handle word aligned part
+ */
+ count = 0;
+ while (cnt >= port_width) {
+ data = 0;
+ for (i = 0; i < port_width; ++i) {
+ data = (data << 8) | *src++;
+ }
+ if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+ return (rc);
+ }
+ wp += port_width;
+ cnt -= port_width;
+ if (count++ > 0x800) {
+ spin_wheel ();
+ count = 0;
+ }
+ }
+
+ if (cnt == 0) {
+ return (0);
+ }
+
+ /*
+ * handle unaligned tail bytes
+ */
+ data = 0;
+ for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
+ data = (data << 8) | *src++;
+ --cnt;
+ }
+ for (; i < port_width; ++i, ++cp) {
+ data = (data << 8) | (*(uchar *) cp);
+ }
+
+ return (write_data (info, wp, SWAP (data)));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word or halfword to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_data (flash_info_t * info, ulong dest, FPW data)
+{
+ FPWV *addr = (FPWV *) dest;
+ ulong status;
+ int flag;
+
+ /* Check if Flash is (sufficiently) erased */
+ if ((*addr & data) != data) {
+ printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr);
+ return (2);
+ }
+ flash_unprotect_sectors (addr);
+ /* Disable interrupts which might cause a timeout here */
+ flag = disable_interrupts ();
+ *addr = (FPW) 0x00400040; /* write setup */
+ *addr = data;
+
+ /* arm simple, non interrupt dependent timer */
+ reset_timer_masked ();
+
+ /* wait while polling the status register */
+ while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
+ if (get_timer_masked () > CONFIG_SYS_FLASH_WRITE_TOUT) {
+ *addr = (FPW) 0x00FF00FF; /* restore read mode */
+ return (1);
+ }
+ }
+ *addr = (FPW) 0x00FF00FF; /* restore read mode */
+ return (0);
+}
+
+void inline spin_wheel (void)
+{
+ static int p = 0;
+ static char w[] = "\\/-";
+
+ printf ("\010%c", w[p]);
+ (++p == 3) ? (p = 0) : 0;
+}
--- /dev/null
+/*
+ * Board specific setup info
+ *
+ * (C) Copyright 2003-2004
+ *
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
+ *
+ * Modified for OMAP730 P2 Board by Dave Peverley, MPC-Data Limited
+ * (http://www.mpc-data.co.uk)
+ *
+ * TODO : Tidy up and change to use system register defines
+ * from omap730.h where possible.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+
+#if defined(CONFIG_OMAP730)
+#include <./configs/omap730.h>
+#endif
+
+_TEXT_BASE:
+ .word TEXT_BASE /* sdram load addr from config.mk */
+
+.globl lowlevel_init
+lowlevel_init:
+ /* Save callers address in r11 - r11 must never be modified */
+ mov r11, lr
+
+ /*------------------------------------------------------*
+ *mask all IRQs by setting all bits in the INTMR default*
+ *------------------------------------------------------*/
+ mov r1, #0xffffffff
+ ldr r0, =REG_IHL1_MIR
+ str r1, [r0]
+ ldr r0, =REG_IHL2_MIR
+ str r1, [r0]
+
+ /*------------------------------------------------------*
+ * Set up ARM CLM registers (IDLECT1) *
+ *------------------------------------------------------*/
+ ldr r0, REG_ARM_IDLECT1
+ ldr r1, VAL_ARM_IDLECT1
+ str r1, [r0]
+
+ /*------------------------------------------------------*
+ * Set up ARM CLM registers (IDLECT2) *
+ *------------------------------------------------------*/
+ ldr r0, REG_ARM_IDLECT2
+ ldr r1, VAL_ARM_IDLECT2
+ str r1, [r0]
+
+ /*------------------------------------------------------*
+ * Set up ARM CLM registers (IDLECT3) *
+ *------------------------------------------------------*/
+ ldr r0, REG_ARM_IDLECT3
+ ldr r1, VAL_ARM_IDLECT3
+ str r1, [r0]
+
+
+ mov r1, #0x01 /* PER_EN bit */
+ ldr r0, REG_ARM_RSTCT2
+ strh r1, [r0] /* CLKM; Peripheral reset. */
+
+ /* Set CLKM to Sync-Scalable */
+ /* I supposedly need to enable the dsp clock before switching */
+ mov r1, #0x1000
+ ldr r0, REG_ARM_SYSST
+ strh r1, [r0]
+ mov r0, #0x400
+1:
+ subs r0, r0, #0x1 /* wait for any bubbles to finish */
+ bne 1b
+ ldr r1, VAL_ARM_CKCTL
+ ldr r0, REG_ARM_CKCTL
+ strh r1, [r0]
+
+ /* a few nops to let settle */
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+
+ /* setup DPLL 1 */
+ /* Ramp up the clock to 96Mhz */
+ ldr r1, VAL_DPLL1_CTL
+ ldr r0, REG_DPLL1_CTL
+ strh r1, [r0]
+ ands r1, r1, #0x10 /* Check if PLL is enabled. */
+ beq lock_end /* Do not look for lock if BYPASS selected */
+2:
+ ldrh r1, [r0]
+ ands r1, r1, #0x01 /* Check the LOCK bit.*/
+ beq 2b /* loop until bit goes hi. */
+lock_end:
+
+ /*------------------------------------------------------*
+ * Turn off the watchdog during init... *
+ *------------------------------------------------------*/
+ ldr r0, REG_WATCHDOG
+ ldr r1, WATCHDOG_VAL1
+ str r1, [r0]
+ ldr r1, WATCHDOG_VAL2
+ str r1, [r0]
+ ldr r0, REG_WSPRDOG
+ ldr r1, WSPRDOG_VAL1
+ str r1, [r0]
+ ldr r0, REG_WWPSDOG
+
+watch1Wait:
+ ldr r1, [r0]
+ tst r1, #0x10
+ bne watch1Wait
+
+ ldr r0, REG_WSPRDOG
+ ldr r1, WSPRDOG_VAL2
+ str r1, [r0]
+ ldr r0, REG_WWPSDOG
+watch2Wait:
+ ldr r1, [r0]
+ tst r1, #0x10
+ bne watch2Wait
+
+ /* Set memory timings corresponding to the new clock speed */
+
+ /* Check execution location to determine current execution location
+ * and branch to appropriate initialization code.
+ */
+ /* Compare physical SDRAM base & current execution location. */
+ and r0, pc, #0xF0000000
+ /* Compare. */
+ cmp r0, #0
+ /* Skip over EMIF-fast initialization if running from SDRAM. */
+ bne skip_sdram
+
+ /*
+ * Delay for SDRAM initialization.
+ */
+ mov r3, #0x1800 /* value should be checked */
+3:
+ subs r3, r3, #0x1 /* Decrement count */
+ bne 3b
+
+ ldr r0, REG_SDRAM_CONFIG
+ ldr r1, SDRAM_CONFIG_VAL
+ str r1, [r0]
+
+ ldr r0, REG_SDRAM_MRS_LEGACY
+ ldr r1, SDRAM_MRS_VAL
+ str r1, [r0]
+
+skip_sdram:
+
+common_tc:
+ /* slow interface */
+ ldr r1, VAL_TC_EMIFS_CS0_CONFIG
+ ldr r0, REG_TC_EMIFS_CS0_CONFIG
+ str r1, [r0] /* Chip Select 0 */
+
+ ldr r1, VAL_TC_EMIFS_CS1_CONFIG
+ ldr r0, REG_TC_EMIFS_CS1_CONFIG
+ str r1, [r0] /* Chip Select 1 */
+ ldr r1, VAL_TC_EMIFS_CS2_CONFIG
+ ldr r0, REG_TC_EMIFS_CS2_CONFIG
+ str r1, [r0] /* Chip Select 2 */
+ ldr r1, VAL_TC_EMIFS_CS3_CONFIG
+ ldr r0, REG_TC_EMIFS_CS3_CONFIG
+ str r1, [r0] /* Chip Select 3 */
+
+ /* 48MHz clock request for UART1 */
+ ldr r1, PERSEUS2_CONFIG_BASE
+ ldrh r0, [r1, #CONFIG_PCC_CONF]
+ orr r0, r0, #CONF_MOD_UART1_CLK_MODE_R
+ strh r0, [r1, #CONFIG_PCC_CONF]
+
+ /* Initialize public and private rheas
+ * - set access factor 2 on both rhea / strobe
+ * - disable write buffer on strb0, enable write buffer on strb1
+ */
+
+ ldr R0, REG_RHEA_PUB_CTL
+ ldr R1, REG_RHEA_PRIV_CTL
+ ldr R2, VAL_RHEA_CTL
+ strh R2, [R0]
+ strh R2, [R1]
+ mov R3, #2 /* disable write buffer on strb0, enable write buffer on strb1 */
+ strh R3, [R0, #0x08] /* arm rhea control reg */
+ strh R3, [R1, #0x08]
+
+ /* enable IRQ and FIQ */
+
+ mrs r4, CPSR
+ bic r4, r4, #IRQ_MASK
+ bic r4, r4, #FIQ_MASK
+ msr CPSR, r4
+
+ /* set TAP CONF to TRI EMULATION */
+
+ ldr r1, [r0, #CONFIG_MODE2]
+ bic r1, r1, #0x18
+ orr r1, r1, #0x10
+ str r1, [r0, #CONFIG_MODE2]
+
+ /* set tdbgen to 1 */
+
+ ldr r0, PERSEUS2_CONFIG_BASE
+ ldr r1, [r0, #CONFIG_MODE1]
+ mov r2, #0x10000
+ orr r1, r1, r2
+ str r1, [r0, #CONFIG_MODE1]
+
+#ifdef CONFIG_P2_OMAP1610
+ /* inserting additional 2 clock cycle hold time for LAN */
+ ldr r0, REG_TC_EMIFS_CS1_ADVANCED
+ ldr r1, VAL_TC_EMIFS_CS1_ADVANCED
+ str r1, [r0]
+#endif
+ /* Start MPU Timer 1 */
+ ldr r0, REG_MPU_LOAD_TIMER
+ ldr r1, VAL_MPU_LOAD_TIMER
+ str r1, [r0]
+
+ ldr r0, REG_MPU_CNTL_TIMER
+ ldr r1, VAL_MPU_CNTL_TIMER
+ str r1, [r0]
+
+ /* back to arch calling code */
+ mov pc, r11
+
+ /* the literal pools origin */
+ .ltorg
+
+REG_TC_EMIFS_CONFIG: /* 32 bits */
+ .word 0xfffecc0c
+REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */
+ .word 0xfffecc10
+REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */
+ .word 0xfffecc14
+REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */
+ .word 0xfffecc18
+REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */
+ .word 0xfffecc1c
+
+#ifdef CONFIG_P2_OMAP730
+REG_TC_EMIFS_CS1_ADVANCED: /* 32 bits */
+ .word 0xfffecc54
+#endif
+
+/* MPU clock/reset/power mode control registers */
+REG_ARM_CKCTL: /* 16 bits */
+ .word 0xfffece00
+
+REG_ARM_IDLECT3: /* 16 bits */
+ .word 0xfffece24
+REG_ARM_IDLECT2: /* 16 bits */
+ .word 0xfffece08
+REG_ARM_IDLECT1: /* 16 bits */
+ .word 0xfffece04
+
+REG_ARM_RSTCT2: /* 16 bits */
+ .word 0xfffece14
+REG_ARM_SYSST: /* 16 bits */
+ .word 0xfffece18
+/* DPLL control registers */
+REG_DPLL1_CTL: /* 16 bits */
+ .word 0xfffecf00
+
+/* Watch Dog register */
+/* secure watchdog stop */
+REG_WSPRDOG:
+ .word 0xfffeb048
+/* watchdog write pending */
+REG_WWPSDOG:
+ .word 0xfffeb034
+
+WSPRDOG_VAL1:
+ .word 0x0000aaaa
+WSPRDOG_VAL2:
+ .word 0x00005555
+
+/* SDRAM config is: auto refresh enabled, 16 bit 4 bank,
+ counter @8192 rows, 10 ns, 8 burst */
+REG_SDRAM_CONFIG:
+ .word 0xfffecc20
+
+REG_SDRAM_MRS_LEGACY:
+ .word 0xfffecc24
+
+REG_WATCHDOG:
+ .word 0xfffec808
+
+REG_MPU_LOAD_TIMER:
+ .word 0xfffec504
+REG_MPU_CNTL_TIMER:
+ .word 0xfffec500
+
+/* Public and private rhea bridge registers definition */
+
+REG_RHEA_PUB_CTL:
+ .word 0xFFFECA00
+
+REG_RHEA_PRIV_CTL:
+ .word 0xFFFED300
+
+/* EMIFF SDRAM Configuration register
+ - self refresh disable
+ - auto refresh enabled
+ - SDRAM type 64 Mb, 16 bits bus 4 banks
+ - power down enabled
+ - SDRAM clock disabled
+ */
+SDRAM_CONFIG_VAL:
+ .word 0x0C017DF4
+
+/* Burst full page length ; cas latency = 3 */
+SDRAM_MRS_VAL:
+ .word 0x00000037
+
+VAL_ARM_CKCTL:
+ .word 0x6505
+VAL_DPLL1_CTL:
+ .word 0x3412
+
+#ifdef CONFIG_P2_OMAP730
+VAL_TC_EMIFS_CS0_CONFIG:
+ .word 0x0000FFF3
+VAL_TC_EMIFS_CS1_CONFIG:
+ .word 0x00004278
+VAL_TC_EMIFS_CS2_CONFIG:
+ .word 0x00004278
+VAL_TC_EMIFS_CS3_CONFIG:
+ .word 0x00004278
+VAL_TC_EMIFS_CS1_ADVANCED:
+ .word 0x00000022
+#endif
+
+VAL_ARM_IDLECT1:
+ .word 0x00000400
+VAL_ARM_IDLECT2:
+ .word 0x00000886
+VAL_ARM_IDLECT3:
+ .word 0x00000015
+
+WATCHDOG_VAL1:
+ .word 0x000000f5
+WATCHDOG_VAL2:
+ .word 0x000000a0
+
+VAL_MPU_LOAD_TIMER:
+ .word 0xffffffff
+VAL_MPU_CNTL_TIMER:
+ .word 0xffffffa1
+
+VAL_RHEA_CTL:
+ .word 0xFF22
+
+/* Config Register vals */
+PERSEUS2_CONFIG_BASE:
+ .word 0xFFFE1000
+
+.equ CONFIG_PCC_CONF, 0xB4
+.equ CONFIG_MODE1, 0x10
+.equ CONFIG_MODE2, 0x14
+.equ CONF_MOD_UART1_CLK_MODE_R, 0x0A
+
+/* misc values */
+.equ IRQ_MASK, 0x80 /* IRQ mask value */
+.equ FIQ_MASK, 0x40 /* FIQ mask value */
--- /dev/null
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#if defined(CONFIG_OMAP730)
+#include <./configs/omap730.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int test_boot_mode(void);
+void spin_up_leds(void);
+void flash__init (void);
+void ether__init (void);
+void set_muxconf_regs (void);
+void peripheral_power_enable (void);
+
+#define FLASH_ON_CS0 1
+#define FLASH_ON_CS3 0
+
+static inline void delay (unsigned long loops)
+{
+ __asm__ volatile ("1:\n"
+ "subs %0, %1, #1\n"
+ "bne 1b":"=r" (loops):"0" (loops));
+}
+
+int test_boot_mode(void)
+{
+ /* Check for CS0 and CS3 address decode swapping */
+ if (*((volatile int *)EMIFS_CONFIG) & 0x00000002)
+ return(FLASH_ON_CS3);
+ else
+ return(FLASH_ON_CS0);
+}
+
+/* Toggle backup LED indication */
+void toggle_backup_led(void)
+{
+ static int backupLEDState = 0; /* Init variable so that the LED will be ON the first time */
+ volatile unsigned int *IOConfReg;
+
+
+ IOConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_5 + GPIO_DATA_OUTPUT);
+
+ if (backupLEDState != 0) {
+ *IOConfReg &= (0xFFFFEFFF);
+ backupLEDState = 0;
+ } else {
+ *IOConfReg |= (0x00001000);
+ backupLEDState = 1;
+ }
+}
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+ /* arch number of OMAP 730 P2 Board - Same as the Innovator! */
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP_PERSEUS2;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = 0x10000100;
+
+ /* Configure MUX settings */
+ set_muxconf_regs ();
+
+ peripheral_power_enable ();
+
+ /* Backup LED indication via GPIO_140 -> Red led if MUX correctly setup */
+ toggle_backup_led();
+
+ /* Hold GSM in reset until needed */
+ *((volatile unsigned short *)M_CTL) &= ~1;
+
+ /*
+ * CSx timings, GPIO Mux ... setup
+ */
+
+ /* Flash: CS0 timings setup */
+ *((volatile unsigned int *) FLASH_CFG_0) = 0x0000fff3;
+ *((volatile unsigned int *) FLASH_ACFG_0_1) = 0x00000088;
+
+ /* Ethernet support trough the debug board */
+ /* CS1 timings setup */
+ *((volatile unsigned int *) FLASH_CFG_1) = 0x0000fff3;
+ *((volatile unsigned int *) FLASH_ACFG_0_1) = 0x00000000;
+
+ /* this speeds up your boot a quite a bit. However to make it
+ * work, you need make sure your kernel startup flush bug is fixed.
+ * ... rkw ...
+ */
+ icache_enable ();
+
+ flash__init ();
+ ether__init ();
+
+ return 0;
+}
+
+int misc_init_r (void)
+{
+ /* currently empty */
+ return (0);
+}
+
+/******************************
+ Routine:
+ Description:
+******************************/
+void flash__init (void)
+{
+ unsigned int regval;
+
+ regval = *((volatile unsigned int *) EMIFS_CONFIG);
+ /* Turn off write protection for flash devices. */
+ regval = regval | 0x0001;
+ *((volatile unsigned int *) EMIFS_CONFIG) = regval;
+}
+
+/*************************************************************
+ Routine:ether__init
+ Description: take the Ethernet controller out of reset and wait
+ for the EEPROM load to complete.
+*************************************************************/
+void ether__init (void)
+{
+#define LAN_RESET_REGISTER 0x0400001c
+
+ *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000;
+ do {
+ *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0001;
+ udelay (100);
+ } while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0001);
+
+ do {
+ *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000;
+ udelay (100);
+ } while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0000);
+
+#define ETH_CONTROL_REG 0x0400030b
+
+ *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
+ udelay (100);
+}
+
+/******************************
+ Routine:
+ Description:
+******************************/
+int dram_init (void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+ return 0;
+}
+
+/******************************************************
+ Routine: set_muxconf_regs
+ Description: Setting up the configuration Mux registers
+ specific to the hardware
+*******************************************************/
+void set_muxconf_regs (void)
+{
+ volatile unsigned int *MuxConfReg;
+ /* set each registers to its reset value; */
+
+ /*
+ * Backup LED Indication
+ */
+
+ /* Configure MUXed pin. Mode 6: GPIO_140 */
+ MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF10);
+ *MuxConfReg &= (0xFFFFFF1F); /* Clear D_MPU_LPG1 */
+ *MuxConfReg |= 0x000000C0; /* Set D_MPU_LPG1 to 0x6 */
+
+ /* Configure GPIO_140 as output */
+ MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_5 + GPIO_DIRECTION_CONTROL);
+ *MuxConfReg &= (0xFFFFEFFF); /* Clear direction (output) for GPIO 140 */
+
+ /*
+ * Configure GPIOs for battery charge & feedback
+ */
+
+ /* Configure MUXed pin. Mode 6: GPIO_35 */
+ MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF3);
+ *MuxConfReg &= 0xFFFFFFF1; /* Clear M_CLK_OUT */
+ *MuxConfReg |= 0x0000000C; /* Set M_CLK_OUT = 0x6 (GPIOs) */
+
+ /* Configure MUXed pin. Mode 6: GPIO_72,73,74 */
+ MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF5);
+ *MuxConfReg &= 0xFFFF1FFF; /* Clear D_DDR */
+ *MuxConfReg |= 0x0000C000; /* Set D_DDR = 0x6 (GPIOs) */
+
+ MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_3 + GPIO_DIRECTION_CONTROL);
+ *MuxConfReg |= 0x00000100; /* Configure GPIO_72 as input */
+ *MuxConfReg &= 0xFFFFFDFF; /* Configure GPIO_73 as output */
+
+ /*
+ * Allow battery charge
+ */
+
+ MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_3 + GPIO_DATA_OUTPUT);
+ *MuxConfReg &= (0xFFFFFDFF); /* Clear GPIO_73 pin */
+
+ /*
+ * Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
+ * It is used as the Ethernet controller interrupt
+ */
+ MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF9);
+ *MuxConfReg &= 0x1FFFFFFF;
+}
+
+/******************************************************
+ Routine: peripheral_power_enable
+ Description: Enable the power for UART1
+*******************************************************/
+void peripheral_power_enable (void)
+{
+ volatile unsigned int *MuxConfReg;
+
+
+ /* Set up pins used by UART */
+
+ /* Start UART clock (48MHz) */
+ MuxConfReg = (volatile unsigned int *) (PERSEUS_PCC_CONF_REG);
+ *MuxConfReg &= (0xFFFFFFF7);
+ *MuxConfReg |= (0x00000008);
+
+ /* Get the UART pin in mode0 */
+ MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF3);
+ *MuxConfReg &= (0xFF1FFFFF);
+ *MuxConfReg &= (0xF1FFFFFF);
+}
projects / u-boot / commitdiff