mvtwsi: convert to CONFIG_SYS_I2C framework

Note this has only been tested on Allwinner sunxi devices (support for which
gets introduced by a later patch).

The kirkwood changes have been compile tested using the wireless_space board
config, the orion5x changes have been compile tested using the edminiv2 board
config.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heiko Schocher <hs@denx.de>

diff --git a/arch/arm/include/asm/arch-kirkwood/config.h b/arch/arm/include/asm/arch-kirkwood/config.h
index 7a688e46b019cc7720b0f28749eb550d1ba4a73e..f7bfa0e74d7f68864a8ee090f77d5e2f4d025574 100644 (file)
--- a/arch/arm/include/asm/arch-kirkwood/config.h
+++ b/arch/arm/include/asm/arch-kirkwood/config.h
@@ -129,7 +129,8 @@
  */
 #ifdef CONFIG_CMD_I2C
 #ifndef CONFIG_SYS_I2C_SOFT
-#define CONFIG_I2C_MVTWSI
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MVTWSI
 #endif
 #define CONFIG_SYS_I2C_SLAVE           0x0
 #define CONFIG_SYS_I2C_SPEED           100000

diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
index e33586d8a6b6ab9b8faa96b5c50ca8eb8d9e6f1a..61e9f3c2400e0ad4e8823407d5eb5a1bf08a7e1a 100644 (file)
--- a/drivers/i2c/Makefile
+++ b/drivers/i2c/Makefile
@@ -7,7 +7,6 @@
 
 obj-$(CONFIG_BFIN_TWI_I2C) += bfin-twi_i2c.o
 obj-$(CONFIG_DW_I2C) += designware_i2c.o
-obj-$(CONFIG_I2C_MVTWSI) += mvtwsi.o
 obj-$(CONFIG_I2C_MV) += mv_i2c.o
 obj-$(CONFIG_I2C_MXS) += mxs_i2c.o
 obj-$(CONFIG_PCA9564_I2C) += pca9564_i2c.o
@@ -19,6 +18,7 @@ obj-$(CONFIG_SYS_I2C_DAVINCI) += davinci_i2c.o
 obj-$(CONFIG_SYS_I2C_FSL) += fsl_i2c.o
 obj-$(CONFIG_SYS_I2C_FTI2C010) += fti2c010.o
 obj-$(CONFIG_SYS_I2C_KONA) += kona_i2c.o
+obj-$(CONFIG_SYS_I2C_MVTWSI) += mvtwsi.o
 obj-$(CONFIG_SYS_I2C_MXC) += mxc_i2c.o
 obj-$(CONFIG_SYS_I2C_OMAP24XX) += omap24xx_i2c.o
 obj-$(CONFIG_SYS_I2C_OMAP34XX) += omap24xx_i2c.o

diff --git a/drivers/i2c/mvtwsi.c b/drivers/i2c/mvtwsi.c
index 5ba0e038624eb5456c1cf1376b34d7206311a4ec..c8b5425a0152ab2d0b50991e6df5100a89fac213 100644 (file)
--- a/drivers/i2c/mvtwsi.c
+++ b/drivers/i2c/mvtwsi.c
@@ -220,11 +220,10 @@ static int twsi_stop(int status)
 
 /*
  * Reset controller.
- * Called at end of i2c_init unsuccessful i2c transactions.
  * Controller reset also resets the baud rate and slave address, so
- * re-establish them.
+ * they must be re-established afterwards.
  */
-static void twsi_reset(u8 baud_rate, u8 slave_address)
+static void twsi_reset(struct i2c_adapter *adap)
 {
        /* ensure controller will be enabled by any twsi*() function */
        twsi_control_flags = MVTWSI_CONTROL_TWSIEN;
@@ -232,23 +231,17 @@ static void twsi_reset(u8 baud_rate, u8 slave_address)
        writel(0, &twsi->soft_reset);
        /* wait 2 ms -- this is what the Marvell LSP does */
        udelay(20000);
-       /* set baud rate */
-       writel(baud_rate, &twsi->baudrate);
-       /* set slave address even though we don't use it */
-       writel(slave_address, &twsi->slave_address);
-       writel(0, &twsi->xtnd_slave_addr);
-       /* assert STOP but don't care for the result */
-       (void) twsi_stop(0);
 }
 
 /*
  * I2C init called by cmd_i2c when doing 'i2c reset'.
  * Sets baud to the highest possible value not exceeding requested one.
  */
-void i2c_init(int requested_speed, int slaveadd)
+static unsigned int twsi_i2c_set_bus_speed(struct i2c_adapter *adap,
+                                          unsigned int requested_speed)
 {
-       int     tmp_speed, highest_speed, n, m;
-       int     baud = 0x44; /* baudrate at controller reset */
+       unsigned int tmp_speed, highest_speed, n, m;
+       unsigned int baud = 0x44; /* baudrate at controller reset */
 
        /* use actual speed to collect progressively higher values */
        highest_speed = 0;
@@ -263,8 +256,21 @@ void i2c_init(int requested_speed, int slaveadd)
                        }
                }
        }
+       writel(baud, &twsi->baudrate);
+       return 0;
+}
+
+static void twsi_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd)
+{
        /* reset controller */
-       twsi_reset(baud, slaveadd);
+       twsi_reset(adap);
+       /* set speed */
+       twsi_i2c_set_bus_speed(adap, speed);
+       /* set slave address even though we don't use it */
+       writel(slaveadd, &twsi->slave_address);
+       writel(0, &twsi->xtnd_slave_addr);
+       /* assert STOP but don't care for the result */
+       (void) twsi_stop(0);
 }
 
 /*
@@ -294,7 +300,7 @@ static int i2c_begin(int expected_start_status, u8 addr)
  * I2C probe called by cmd_i2c when doing 'i2c probe'.
  * Begin read, nak data byte, end.
  */
-int i2c_probe(uchar chip)
+static int twsi_i2c_probe(struct i2c_adapter *adap, uchar chip)
 {
        u8 dummy_byte;
        int status;
@@ -320,12 +326,13 @@ int i2c_probe(uchar chip)
  * cmd_eeprom, so we have to choose here, and for the moment that'll be
  * a repeated start without a preceding stop.
  */
-int i2c_read(u8 dev, uint addr, int alen, u8 *data, int length)
+static int twsi_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
+                       int alen, uchar *data, int length)
 {
        int status;
 
        /* begin i2c write to send the address bytes */
-       status = i2c_begin(MVTWSI_STATUS_START, (dev << 1));
+       status = i2c_begin(MVTWSI_STATUS_START, (chip << 1));
        /* send addr bytes */
        while ((status == 0) && alen--)
                status = twsi_send(addr >> (8*alen),
@@ -333,7 +340,7 @@ int i2c_read(u8 dev, uint addr, int alen, u8 *data, int length)
        /* begin i2c read to receive eeprom data bytes */
        if (status == 0)
                status = i2c_begin(
-                       MVTWSI_STATUS_REPEATED_START, (dev << 1) | 1);
+                       MVTWSI_STATUS_REPEATED_START, (chip << 1) | 1);
        /* prepare ACK if at least one byte must be received */
        if (length > 0)
                twsi_control_flags |= MVTWSI_CONTROL_ACK;
@@ -355,12 +362,13 @@ int i2c_read(u8 dev, uint addr, int alen, u8 *data, int length)
  * I2C write called by cmd_i2c when doing 'i2c write' and by cmd_eeprom.c
  * Begin write, send address byte(s), send data bytes, end.
  */
-int i2c_write(u8 dev, uint addr, int alen, u8 *data, int length)
+static int twsi_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
+                       int alen, uchar *data, int length)
 {
        int status;
 
        /* begin i2c write to send the eeprom adress bytes then data bytes */
-       status = i2c_begin(MVTWSI_STATUS_START, (dev << 1));
+       status = i2c_begin(MVTWSI_STATUS_START, (chip << 1));
        /* send addr bytes */
        while ((status == 0) && alen--)
                status = twsi_send(addr >> (8*alen),
@@ -374,21 +382,7 @@ int i2c_write(u8 dev, uint addr, int alen, u8 *data, int length)
        return status;
 }
 
-/*
- * Bus set routine: we only support bus 0.
- */
-int i2c_set_bus_num(unsigned int bus)
-{
-       if (bus > 0) {
-               return -1;
-       }
-       return 0;
-}
-
-/*
- * Bus get routine: hard-return bus 0.
- */
-unsigned int i2c_get_bus_num(void)
-{
-       return 0;
-}
+U_BOOT_I2C_ADAP_COMPLETE(twsi0, twsi_i2c_init, twsi_i2c_probe,
+                        twsi_i2c_read, twsi_i2c_write,
+                        twsi_i2c_set_bus_speed,
+                        CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE, 0)

diff --git a/include/configs/edminiv2.h b/include/configs/edminiv2.h
index 8b9f66a29c18d2bf5a422d469826e2f107f3e3f0..77717a84aeec9dc977cf57875ef81081e6d9ba28 100644 (file)
--- a/include/configs/edminiv2.h
+++ b/include/configs/edminiv2.h
@@ -187,7 +187,8 @@
  * I2C related stuff
  */
 #ifdef CONFIG_CMD_I2C
-#define CONFIG_I2C_MVTWSI
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MVTWSI
 #define CONFIG_I2C_MVTWSI_BASE         ORION5X_TWSI_BASE
 #define CONFIG_SYS_I2C_SLAVE           0x0
 #define CONFIG_SYS_I2C_SPEED           100000