Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/rpxsuper/*
- Remove include/configs/RPXsuper.h
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := rpxsuper.o flash.o mii_phy.o
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Marius Groeger <mgroeger@sysgo.de>
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * Flash Routines for AMD 29F080B devices
- * Added support for 64bit and AMD 29DL323B
- *
- *--------------------------------------------------------------------
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-#include <asm/io.h>
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-#define RD_SWP32(x) in_le32((volatile u32*)x)
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-
-static ulong flash_get_size (vu_long *addr, flash_info_t *info);
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init(void)
-{
- int i;
-
- /* Init: no FLASHes known */
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i)
- flash_info[i].flash_id = FLASH_UNKNOWN;
-
- /* for now, only support the 4 MB Flash SIMM */
- (void)flash_get_size((vu_long *) CONFIG_SYS_FLASH0_BASE,
- &flash_info[0]);
-
- /*
- * protect monitor and environment sectors
- */
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH0_BASE
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
- &flash_info[0]);
-#endif
-
-#if defined(CONFIG_ENV_IS_IN_FLASH) && defined(CONFIG_ENV_ADDR)
-#ifndef CONFIG_ENV_SIZE
-#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-#endif
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]);
-#endif
-
- return CONFIG_SYS_FLASH0_SIZE * 1024 * 1024;
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case (AMD_MANUFACT & FLASH_VENDMASK):
- printf ("AMD ");
- break;
- case (FUJ_MANUFACT & FLASH_VENDMASK):
- printf ("FUJITSU ");
- break;
- case (SST_MANUFACT & FLASH_VENDMASK):
- printf ("SST ");
- break;
- default:
- printf ("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case (AMD_ID_DL323B & FLASH_TYPEMASK):
- printf("AM29DL323B (32 MBit)\n");
- break;
- default:
- printf ("Unknown Chip Type\n");
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; ++i) {
- if ((i % 5) == 0) printf ("\n ");
- printf (" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " "
- );
- }
- printf ("\n");
- return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-static ulong flash_get_size (vu_long *addr, flash_info_t *info)
-{
- short i;
- vu_long vendor[2], devid[2];
- ulong base = (ulong)addr;
-
- /* Reset and Write auto select command: read Manufacturer ID */
- addr[0] = 0xf0f0f0f0;
- addr[2 * 0x0555] = 0xAAAAAAAA;
- addr[2 * 0x02AA] = 0x55555555;
- addr[2 * 0x0555] = 0x90909090;
- addr[1] = 0xf0f0f0f0;
- addr[2 * 0x0555 + 1] = 0xAAAAAAAA;
- addr[2 * 0x02AA + 1] = 0x55555555;
- addr[2 * 0x0555 + 1] = 0x90909090;
- udelay (1000);
-
- vendor[0] = RD_SWP32(&addr[0]);
- vendor[1] = RD_SWP32(&addr[1]);
- if (vendor[0] != vendor[1] || vendor[0] != AMD_MANUFACT) {
- info->size = 0;
- goto out;
- }
-
- devid[0] = RD_SWP32(&addr[2]);
- devid[1] = RD_SWP32(&addr[3]);
-
- if (devid[0] == AMD_ID_DL323B) {
- /*
- * we have 2 Banks
- * Bank 1 (23 Sectors): 0-7=8kbyte, 8-22=64kbyte
- * Bank 2 (48 Sectors): 23-70=64kbyte
- */
- info->flash_id = (AMD_MANUFACT & FLASH_VENDMASK) |
- (AMD_ID_DL323B & FLASH_TYPEMASK);
- info->sector_count = 71;
- info->size = 4 * (8 * 8 + 63 * 64) * 1024;
- }
- else {
- info->size = 0;
- goto out;
- }
-
- /* set up sector start address table */
- for (i = 0; i < 8; i++) {
- info->start[i] = base + (i * 0x8000);
- }
- for (i = 8; i < info->sector_count; i++) {
- info->start[i] = base + (i * 0x40000) + 8 * 0x8000 - 8 * 0x40000;
- }
-
- /* check for protected sectors */
- for (i = 0; i < info->sector_count; i++) {
- /* read sector protection at sector address */
- addr = (volatile unsigned long *)(info->start[i]);
- addr[2 * 0x0555] = 0xAAAAAAAA;
- addr[2 * 0x02AA] = 0x55555555;
- addr[2 * 0x0555] = 0x90909090;
- addr[2 * 0x0555 + 1] = 0xAAAAAAAA;
- addr[2 * 0x02AA + 1] = 0x55555555;
- addr[2 * 0x0555 + 1] = 0x90909090;
- udelay (1000);
- base = RD_SWP32(&addr[4]);
- base |= RD_SWP32(&addr[5]);
- info->protect[i] = base & 0x00010001 ? 1 : 0;
- }
- addr = (vu_long*)info->start[0];
-
-out:
- /* reset command */
- addr[0] = 0xf0f0f0f0;
- addr[1] = 0xf0f0f0f0;
-
- return info->size;
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
- vu_long *addr = (vu_long*)(info->start[0]);
- int flag, prot, sect, l_sect;
- ulong start, now, last;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- l_sect = -1;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr[2 * 0x0555] = 0xAAAAAAAA;
- addr[2 * 0x02AA] = 0x55555555;
- addr[2 * 0x0555] = 0x80808080;
- addr[2 * 0x0555] = 0xAAAAAAAA;
- addr[2 * 0x02AA] = 0x55555555;
- addr[2 * 0x0555 + 1] = 0xAAAAAAAA;
- addr[2 * 0x02AA + 1] = 0x55555555;
- addr[2 * 0x0555 + 1] = 0x80808080;
- addr[2 * 0x0555 + 1] = 0xAAAAAAAA;
- addr[2 * 0x02AA + 1] = 0x55555555;
- udelay (100);
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect<=s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr = (vu_long*)(info->start[sect]);
- addr[0] = 0x30303030;
- addr[1] = 0x30303030;
- l_sect = sect;
- }
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- /*
- * We wait for the last triggered sector
- */
- if (l_sect < 0)
- goto DONE;
-
- start = get_timer (0);
- last = start;
- addr = (vu_long*)(info->start[l_sect]);
- while ( (addr[0] & 0x80808080) != 0x80808080 ||
- (addr[1] & 0x80808080) != 0x80808080) {
- if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- return 1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- serial_putc ('.');
- last = now;
- }
- }
-
- DONE:
- /* reset to read mode */
- addr = (volatile unsigned long *)info->start[0];
- addr[0] = 0xF0F0F0F0; /* reset bank */
- addr[1] = 0xF0F0F0F0; /* reset bank */
-
- printf (" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- ulong cp, wp, data;
- int i, l, rc;
-
- wp = (addr & ~3); /* get lower word aligned address */
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i=0, cp=wp; i<l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
- for (; i<4 && cnt>0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt==0 && i<4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= 4) {
- data = 0;
- for (i=0; i<4; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- cnt -= 4;
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i<4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- return (write_word(info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
- vu_long *addr = (vu_long*)(info->start[0]);
- ulong start;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*((vu_long *)dest) & data) != data) {
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- if ((dest & 0x00000004) == 0) {
- addr[2 * 0x0555] = 0xAAAAAAAA;
- addr[2 * 0x02AA] = 0x55555555;
- addr[2 * 0x0555] = 0xA0A0A0A0;
- }
- else {
- addr[2 * 0x0555 + 1] = 0xAAAAAAAA;
- addr[2 * 0x02AA + 1] = 0x55555555;
- addr[2 * 0x0555 + 1] = 0xA0A0A0A0;
- }
-
- *((vu_long *)dest) = data;
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* data polling for D7 */
- start = get_timer (0);
- while ((*((vu_long *)dest) & 0x80808080) != (data & 0x80808080)) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- return (1);
- }
- }
- return (0);
-}
-
-/*-----------------------------------------------------------------------
- */
+++ /dev/null
-#include <common.h>
-#include <mii_phy.h>
-#include "rpxsuper.h"
-
-#define MII_MDIO 0x01
-#define MII_MDCK 0x02
-#define MII_MDIR 0x04
-
-void
-mii_discover_phy(void)
-{
- int known;
- unsigned short phy_reg;
- unsigned long phy_id;
-
- known = 0;
- printf("Discovering phy @ 0: ");
- phy_id = mii_phy_read(2) << 16;
- phy_id |= mii_phy_read(3);
- if ((phy_id & 0xFFFFFC00) == 0x00137800) {
- printf("Level One ");
- if ((phy_id & 0x000003F0) == 0xE0) {
- printf("LXT971A Revision %d\n", (int)(phy_id & 0xF));
- known = 1;
- }
- else printf("unknown type\n");
- }
- else printf("unknown OUI = 0x%08lX\n", phy_id);
-
- phy_reg = mii_phy_read(1);
- if (!(phy_reg & 0x0004)) printf("Link is down\n");
- if (!(phy_reg & 0x0020)) printf("Auto-negotiation not complete\n");
- if (phy_reg & 0x0002) printf("Jabber condition detected\n");
- if (phy_reg & 0x0010) printf("Remote fault condition detected \n");
-
- if (known) {
- phy_reg = mii_phy_read(17);
- if (phy_reg & 0x0400)
- printf("Phy operating at %d MBit/s in %s-duplex mode\n",
- phy_reg & 0x4000 ? 100 : 10,
- phy_reg & 0x0200 ? "full" : "half");
- else
- printf("bad link!!\n");
-/*
-left off: no link, green 100MBit, yellow 10MBit
-right off: no activity, green full-duplex, yellow half-duplex
-*/
- mii_phy_write(20, 0x0452);
- }
-}
-
-unsigned short
-mii_phy_read(unsigned short reg)
-{
- int i;
- unsigned short tmp, val = 0, adr = 0;
- t_rpx_regs *regs = (t_rpx_regs*)CONFIG_SYS_REGS_BASE;
-
- tmp = 0x6002 | (adr << 7) | (reg << 2);
- regs->bcsr4 = 0xC3;
- for (i = 0; i < 64; i++) {
- regs->bcsr4 ^= MII_MDCK;
- }
- for (i = 0; i < 16; i++) {
- regs->bcsr4 &= ~MII_MDCK;
- if (tmp & 0x8000) regs->bcsr4 |= MII_MDIO;
- else regs->bcsr4 &= ~MII_MDIO;
- regs->bcsr4 |= MII_MDCK;
- tmp <<= 1;
- }
- regs->bcsr4 |= MII_MDIR;
- for (i = 0; i < 16; i++) {
- val <<= 1;
- regs->bcsr4 = MII_MDIO | (regs->bcsr4 | MII_MDCK);
- if (regs->bcsr4 & MII_MDIO) val |= 1;
- regs->bcsr4 = MII_MDIO | (regs->bcsr4 &= ~MII_MDCK);
- }
- return val;
-}
-
-void
-mii_phy_write(unsigned short reg, unsigned short val)
-{
- int i;
- unsigned short tmp, adr = 0;
- t_rpx_regs *regs = (t_rpx_regs*)CONFIG_SYS_REGS_BASE;
-
- tmp = 0x5002 | (adr << 7) | (reg << 2);
- regs->bcsr4 = 0xC3;
- for (i = 0; i < 64; i++) {
- regs->bcsr4 ^= MII_MDCK;
- }
- for (i = 0; i < 16; i++) {
- regs->bcsr4 &= ~MII_MDCK;
- if (tmp & 0x8000) regs->bcsr4 |= MII_MDIO;
- else regs->bcsr4 &= ~MII_MDIO;
- regs->bcsr4 |= MII_MDCK;
- tmp <<= 1;
- }
- for (i = 0; i < 16; i++) {
- regs->bcsr4 &= ~MII_MDCK;
- if (val & 0x8000) regs->bcsr4 |= MII_MDIO;
- else regs->bcsr4 &= ~MII_MDIO;
- regs->bcsr4 |= MII_MDCK;
- val <<= 1;
- }
-}
+++ /dev/null
-Hi,
-
-so this is the port to the Embedded Planet RPX Super Board.
-
-ATTENTION
-This code is only tested on the AY-Version, which is an early release with some
-hardware bugs. The main problem is that this board uses the default Hard Reset
-Configuration Word and not the 4 bytes located at start of FLASH because at
-0xFE000000 is no FLASH. The FLASH consists out of 4 chips each 16bits wide. Be
-carefull, the bytes are swapped. So DQ0-7 is the high byte, DQ8-15 ist the low
-byte.
-
-The icache can only manually be enabled after reset.
-The FLASH and main SDRAM is working with icache enabled.
-The local SDRAM can only be used as data memory when icache is enabled.
-If U-Boot runs in local SDRAM, TFTP does not work.
-The functions in mii_phy.c are all working. Call mii_phy_discover() out of
-eth_init() and solve the linker error.
-I2C, RTC/NVRAM and PCMCIA are not working yet.
-
-TODO
-The 32MB local SDRAM is working but not shown in the startup messages of
-U-Boot. If you locate U-Boot or any other program to this area it won't run.
-Turning the ichache off does not solve this problem.
-
-As I won't buy another RPX Super there might be some little work to do for you
-getting this U-Boot port running on the final board.
-
-
-frank.morauf@salzbrenner.com
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2001
- * Advent Networks, Inc. <http://www.adventnetworks.com>
- * Jay Monkman <jtm@smoothsmoothie.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ioports.h>
-#include <mpc8260.h>
-#include "rpxsuper.h"
-
-/*
- * I/O Port configuration table
- *
- * if conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- */
-
-const iop_conf_t iop_conf_tab[4][32] = {
-
- /* Port A configuration */
- { /* conf ppar psor pdir podr pdat */
- /* PA31 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 *ATMTXEN */
- /* PA30 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMTCA */
- /* PA29 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMTSOC */
- /* PA28 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 *ATMRXEN */
- /* PA27 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMRSOC */
- /* PA26 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMRCA */
- /* PA25 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMTXD[0] */
- /* PA24 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMTXD[1] */
- /* PA23 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMTXD[2] */
- /* PA22 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMTXD[3] */
- /* PA21 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMTXD[4] */
- /* PA20 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMTXD[5] */
- /* PA19 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMTXD[6] */
- /* PA18 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMTXD[7] */
- /* PA17 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMRXD[7] */
- /* PA16 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMRXD[6] */
- /* PA15 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMRXD[5] */
- /* PA14 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMRXD[4] */
- /* PA13 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */
- /* PA12 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */
- /* PA11 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */
- /* PA10 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMRXD[0] */
- /* PA9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC2 TXD */
- /* PA8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC2 RXD */
- /* PA7 */ { 1, 0, 0, 0, 0, 0 }, /* PA7 */
- /* PA6 */ { 1, 0, 0, 0, 0, 0 }, /* PA6 */
- /* PA5 */ { 1, 0, 0, 0, 0, 0 }, /* PA5 */
- /* PA4 */ { 1, 0, 0, 0, 0, 0 }, /* PA4 */
- /* PA3 */ { 1, 0, 0, 0, 0, 0 }, /* PA3 */
- /* PA2 */ { 1, 0, 0, 0, 0, 0 }, /* PA2 */
- /* PA1 */ { 1, 0, 0, 0, 0, 0 }, /* PA1 */
- /* PA0 */ { 1, 0, 0, 0, 0, 0 } /* PA0 */
- },
-
- /* Port B configuration */
- { /* conf ppar psor pdir podr pdat */
- /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */
- /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */
- /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */
- /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */
- /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */
- /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */
- /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */
- /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */
- /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */
- /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */
- /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */
- /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */
- /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */
- /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */
- /* PB17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RX_DV */
- /* PB16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RX_ER */
- /* PB15 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TX_ER */
- /* PB14 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TX_EN */
- /* PB13 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII COL */
- /* PB12 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII CRS */
- /* PB11 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RxD[3] */
- /* PB10 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RxD[2] */
- /* PB9 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RxD[1] */
- /* PB8 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RxD[0] */
- /* PB7 */ { 0, 0, 0, 0, 0, 0 }, /* PB7 */
- /* PB6 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TxD[1] */
- /* PB5 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TxD[2] */
- /* PB4 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TxD[3] */
- /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
- },
-
- /* Port C */
- { /* conf ppar psor pdir podr pdat */
- /* PC31 */ { 1, 0, 0, 1, 0, 0 }, /* PC31 */
- /* PC30 */ { 1, 0, 0, 1, 0, 0 }, /* PC30 */
- /* PC29 */ { 1, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */
- /* PC28 */ { 1, 0, 0, 1, 0, 0 }, /* PC28 */
- /* PC27 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TxD[0] */
- /* PC26 */ { 1, 0, 0, 1, 0, 0 }, /* PC26 */
- /* PC25 */ { 1, 0, 0, 1, 0, 0 }, /* PC25 */
- /* PC24 */ { 1, 0, 0, 1, 0, 0 }, /* PC24 */
- /* PC23 */ { 1, 1, 0, 1, 0, 0 }, /* ATMTFCLK */
- /* PC22 */ { 1, 1, 0, 0, 0, 0 }, /* ATMRFCLK */
- /* PC21 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */
- /* PC20 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */
- /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK */
- /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII TX_CLK */
- /* PC17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RX_CLK */
- /* PC16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII TX_CLK */
- /* PC15 */ { 1, 0, 0, 0, 0, 0 }, /* PC15 */
- /* PC14 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */
- /* PC13 */ { 1, 0, 0, 1, 0, 0 }, /* PC13 */
- /* PC12 */ { 1, 0, 0, 1, 0, 0 }, /* PC12 */
- /* PC11 */ { 1, 0, 0, 1, 0, 0 }, /* PC11 */
- /* PC10 */ { 1, 0, 0, 1, 0, 0 }, /* FCC2 MDC */
- /* PC9 */ { 1, 0, 0, 1, 0, 0 }, /* FCC2 MDIO */
- /* PC8 */ { 1, 0, 0, 1, 0, 0 }, /* PC8 */
- /* PC7 */ { 1, 0, 0, 1, 0, 0 }, /* PC7 */
- /* PC6 */ { 1, 0, 0, 1, 0, 0 }, /* PC6 */
- /* PC5 */ { 1, 0, 0, 1, 0, 0 }, /* PC5 */
- /* PC4 */ { 1, 0, 0, 1, 0, 0 }, /* PC4 */
- /* PC3 */ { 1, 0, 0, 1, 0, 0 }, /* PC3 */
- /* PC2 */ { 1, 0, 0, 1, 0, 1 }, /* ENET FDE */
- /* PC1 */ { 1, 0, 0, 1, 0, 0 }, /* ENET DSQE */
- /* PC0 */ { 1, 0, 0, 1, 0, 0 }, /* ENET LBK */
- },
-
- /* Port D */
- { /* conf ppar psor pdir podr pdat */
- /* PD31 */ { 1, 0, 0, 0, 0, 0 }, /* SCC1 EN RxD */
- /* PD30 */ { 1, 0, 0, 0, 0, 0 }, /* SCC1 EN TxD */
- /* PD29 */ { 1, 0, 0, 0, 0, 0 }, /* SCC1 EN TENA */
- /* PD28 */ { 1, 0, 0, 0, 0, 0 }, /* PD28 */
- /* PD27 */ { 1, 0, 0, 0, 0, 0 }, /* PD27 */
- /* PD26 */ { 1, 0, 0, 0, 0, 0 }, /* PD26 */
- /* PD25 */ { 1, 0, 0, 0, 0, 0 }, /* PD25 */
- /* PD24 */ { 1, 0, 0, 0, 0, 0 }, /* PD24 */
- /* PD23 */ { 1, 0, 0, 0, 0, 0 }, /* PD23 */
- /* PD22 */ { 1, 0, 0, 0, 0, 0 }, /* PD22 */
- /* PD21 */ { 1, 0, 0, 0, 0, 0 }, /* PD21 */
- /* PD20 */ { 1, 0, 0, 0, 0, 0 }, /* PD20 */
- /* PD19 */ { 1, 0, 0, 0, 0, 0 }, /* PD19 */
- /* PD18 */ { 1, 0, 0, 0, 0, 0 }, /* PD19 */
- /* PD17 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */
- /* PD16 */ { 1, 0, 0, 0, 0, 0 }, /* FCC1 ATMTXPRTY */
- /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */
- /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */
- /* PD13 */ { 1, 0, 0, 0, 0, 0 }, /* PD13 */
- /* PD12 */ { 1, 0, 0, 0, 0, 0 }, /* PD12 */
- /* PD11 */ { 1, 0, 0, 0, 0, 0 }, /* PD11 */
- /* PD10 */ { 1, 0, 0, 0, 0, 0 }, /* PD10 */
- /* PD9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC1 TXD */
- /* PD8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC1 RXD */
- /* PD7 */ { 1, 0, 0, 0, 0, 0 }, /* PD7 */
- /* PD6 */ { 1, 0, 0, 0, 0, 0 }, /* PD6 */
- /* PD5 */ { 1, 0, 0, 0, 0, 0 }, /* PD5 */
- /* PD4 */ { 1, 0, 0, 0, 0, 0 }, /* PD4 */
- /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
- }
-};
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Setup CS4 to enable the Board Control/Status registers.
- * Otherwise the smcs won't work.
-*/
-int board_early_init_f (void)
-{
- volatile t_rpx_regs *regs = (t_rpx_regs*)CONFIG_SYS_REGS_BASE;
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile memctl8260_t *memctl = &immap->im_memctl;
- memctl->memc_br4 = CONFIG_SYS_BR4_PRELIM;
- memctl->memc_or4 = CONFIG_SYS_OR4_PRELIM;
- regs->bcsr1 = 0x70; /* to enable terminal no SMC1 */
- regs->bcsr2 = 0x20; /* mut be written to enable writing FLASH */
- return 0;
-}
-
-void
-reset_phy(void)
-{
- volatile t_rpx_regs *regs = (t_rpx_regs*)CONFIG_SYS_REGS_BASE;
- regs->bcsr4 = 0xC3;
-}
-
-/*
- * Check Board Identity:
- */
-
-int checkboard(void)
-{
- volatile t_rpx_regs *regs = (t_rpx_regs*)CONFIG_SYS_REGS_BASE;
- printf ("Board: Embedded Planet RPX Super, Revision %d\n",
- regs->bcsr0 >> 4);
-
- return 0;
-}
-
-/* ------------------------------------------------------------------------- */
-
-phys_size_t initdram(int board_type)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile memctl8260_t *memctl = &immap->im_memctl;
- volatile uchar c = 0, *ramaddr;
- ulong psdmr, lsdmr, bcr;
- long size = 0;
- int i;
-
- psdmr = CONFIG_SYS_PSDMR;
- lsdmr = CONFIG_SYS_LSDMR;
-
- /*
- * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35):
- *
- * "At system reset, initialization software must set up the
- * programmable parameters in the memory controller banks registers
- * (ORx, BRx, P/LSDMR). After all memory parameters are configured,
- * system software should execute the following initialization sequence
- * for each SDRAM device.
- *
- * 1. Issue a PRECHARGE-ALL-BANKS command
- * 2. Issue eight CBR REFRESH commands
- * 3. Issue a MODE-SET command to initialize the mode register
- *
- * The initial commands are executed by setting P/LSDMR[OP] and
- * accessing the SDRAM with a single-byte transaction."
- *
- * The appropriate BRx/ORx registers have already been set when we
- * get here. The SDRAM can be accessed at the address CONFIG_SYS_SDRAM_BASE.
- */
-
- size = CONFIG_SYS_SDRAM0_SIZE;
- bcr = immap->im_siu_conf.sc_bcr;
- immap->im_siu_conf.sc_bcr = (bcr & ~BCR_EBM);
-
- memctl->memc_mptpr = CONFIG_SYS_MPTPR;
-
- ramaddr = (uchar *)(CONFIG_SYS_SDRAM0_BASE);
- memctl->memc_psrt = CONFIG_SYS_PSRT;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_PREA;
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR;
- for (i = 0; i < 8; i++)
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_MRW;
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN;
- *ramaddr = c;
-
- immap->im_siu_conf.sc_bcr = bcr;
-
-#ifndef CONFIG_SYS_RAMBOOT
-/* size += CONFIG_SYS_SDRAM1_SIZE; */
- ramaddr = (uchar *)(CONFIG_SYS_SDRAM1_BASE);
- memctl->memc_lsrt = CONFIG_SYS_LSRT;
-
- memctl->memc_lsdmr = lsdmr | PSDMR_OP_PREA;
- *ramaddr = c;
-
- memctl->memc_lsdmr = lsdmr | PSDMR_OP_CBRR;
- for (i = 0; i < 8; i++)
- *ramaddr = c;
-
- memctl->memc_lsdmr = lsdmr | PSDMR_OP_MRW;
- *ramaddr = c;
-
- memctl->memc_lsdmr = lsdmr | PSDMR_OP_NORM | PSDMR_RFEN;
- *ramaddr = c;
-#endif
-
- /* return total ram size */
- return (size * 1024 * 1024);
-}
+++ /dev/null
-#ifndef __RPX8260_H__
-#define __RPX8260_H__
-
-typedef struct tt_rpx_regs
-{
- volatile unsigned char bcsr0;
- volatile unsigned char bcsr1;
- volatile unsigned char bcsr2;
- volatile unsigned char bcsr3;
- volatile unsigned char bcsr4;
- volatile unsigned char bcsr5;
- volatile unsigned char bcsr6;
- volatile unsigned char bcsr7;
- volatile unsigned char bcsr8;
- volatile unsigned char bcsr9;
- volatile unsigned char bcsr10;
- volatile unsigned char bcsr11;
- volatile unsigned char bcsr12;
- volatile unsigned char bcsr13;
- volatile unsigned char bcsr14;
- volatile unsigned char bcsr15;
-} t_rpx_regs;
-typedef t_rpx_regs* tp_rpx_regs;
-
-#endif
Orphan powerpc 74xx_7xx - - evb64260 EVB64260 - -
Orphan powerpc mpc824x - - mousse MOUSSE - -
Orphan powerpc mpc8260 - - - rsdproto - -
-Orphan powerpc mpc8260 - - rpxsuper RPXsuper - -
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+RPXsuper powerpc mpc8260 - 2014-04-04
RPXClassic powerpc mpc8xx - 2014-04-04
RPXlite powerpc mpc8xx - 2014-04-04
genietv powerpc mpc8xx - 2014-04-04
+++ /dev/null
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_SYS_TEXT_BASE 0x80F00000
-
-/*****************************************************************************
- *
- * These settings must match the way _your_ board is set up
- *
- *****************************************************************************/
-/* for the AY-Revision which does not use the HRCW */
-#define CONFIG_SYS_DEFAULT_IMMR 0x00010000
-
-/* What is the oscillator's (UX2) frequency in Hz? */
-#define CONFIG_8260_CLKIN (66 * 1000 * 1000)
-
-/* How is switch S2 set? We really only want the MODCK[1-3] bits, so
- * only the 3 least significant bits are important.
-*/
-#define CONFIG_SYS_SBC_S2 0x04
-
-/* What should MODCK_H be? It is dependent on the oscillator
- * frequency, MODCK[1-3], and desired CPM and core frequencies.
- * Some example values (all frequencies are in MHz):
- *
- * MODCK_H MODCK[1-3] Osc CPM Core
- * 0x2 0x2 33 133 133
- * 0x2 0x4 33 133 200
- * 0x5 0x5 66 133 133
- * 0x5 0x7 66 133 200
- */
-#define CONFIG_SYS_SBC_MODCK_H 0x06
-
-#define CONFIG_SYS_SBC_BOOT_LOW 1 /* only for HRCW */
-#undef CONFIG_SYS_SBC_BOOT_LOW
-
-/* What should the base address of the main FLASH be and how big is
- * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE.
- * The main FLASH is whichever is connected to *CS0. U-Boot expects
- * this to be the SIMM.
- */
-#define CONFIG_SYS_FLASH0_BASE 0x80000000
-#define CONFIG_SYS_FLASH0_SIZE 16
-
-/* What should the base address of the secondary FLASH be and how big
- * is it (in Mbytes)? The secondary FLASH is whichever is connected
- * to *CS6. U-Boot expects this to be the on board FLASH. If you don't
- * want it enabled, don't define these constants.
- */
-#define CONFIG_SYS_FLASH1_BASE 0
-#define CONFIG_SYS_FLASH1_SIZE 0
-#undef CONFIG_SYS_FLASH1_BASE
-#undef CONFIG_SYS_FLASH1_SIZE
-
-/* What should be the base address of SDRAM DIMM and how big is
- * it (in Mbytes)?
-*/
-#define CONFIG_SYS_SDRAM0_BASE 0x00000000
-#define CONFIG_SYS_SDRAM0_SIZE 64
-
-/* What should be the base address of SDRAM DIMM and how big is
- * it (in Mbytes)?
-*/
-#define CONFIG_SYS_SDRAM1_BASE 0x04000000
-#define CONFIG_SYS_SDRAM1_SIZE 32
-
-/* What should be the base address of the LEDs and switch S0?
- * If you don't want them enabled, don't define this.
- */
-#define CONFIG_SYS_LED_BASE 0x00000000
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere.
- */
-#define CONFIG_CONS_ON_SMC /* define if console on SMC */
-#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on neither */
-#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-#undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */
-#define CONFIG_ETHER_ON_FCC /* define if ethernet on FCC */
-#undef CONFIG_ETHER_NONE /* define if ethernet on neither */
-#define CONFIG_ETHER_INDEX 3 /* which SCC/FCC channel for ethernet */
-
-#if ( CONFIG_ETHER_INDEX == 3 )
-
-/*
- * - Rx-CLK is CLK15
- * - Tx-CLK is CLK16
- * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
- * - Enable Half Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
-# define CONFIG_SYS_CPMFCR_RAMTYPE 0
-/*#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) */
-# define CONFIG_SYS_FCC_PSMR 0
-
-#else /* CONFIG_ETHER_INDEX */
-# error "on RPX Super ethernet must be FCC3"
-#endif /* CONFIG_ETHER_INDEX */
-
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-
-/* Define this to reserve an entire FLASH sector (256 KB) for
- * environment variables. Otherwise, the environment will be
- * put in the same sector as U-Boot, and changing variables
- * will erase U-Boot temporarily
- */
-#define CONFIG_ENV_IN_OWN_SECT
-
-/* Define to allow the user to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* What should the console's baud rate be? */
-#define CONFIG_BAUDRATE 115200
-
-/* Ethernet MAC address */
-#define CONFIG_ETHADDR 08:00:22:50:70:63
-
-#define CONFIG_IPADDR 192.168.1.99
-#define CONFIG_SERVERIP 192.168.1.3
-
-/* Set to a positive value to delay for running BOOTCOMMAND */
-#define CONFIG_BOOTDELAY -1
-
-/* undef this to save memory */
-#define CONFIG_SYS_LONGHELP
-
-/* Monitor Command Prompt */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_REGINFO
-
-#undef CONFIG_CMD_KGDB
-
-
-/* Where do the internal registers live? */
-#define CONFIG_SYS_IMMR 0xF0000000
-
-/* Where do the on board registers (CS4) live? */
-#define CONFIG_SYS_REGS_BASE 0xFA000000
-
-/*****************************************************************************
- *
- * You should not have to modify any of the following settings
- *
- *****************************************************************************/
-
-#define CONFIG_RPXSUPER 1 /* on an Embedded Planet RPX Super Board */
-#define CONFIG_CPM2 1 /* Has a CPM2 */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */
-
-/*
- * Miscellaneous configurable options
- */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
-
-#define CONFIG_SYS_MAXARGS 8 /* max number of command args */
-
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x04000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x06000000 /* 64-96 MB in SDRAM */
-
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM0_BASE
-
-/*-----------------------------------------------------------------------
- * Hard Reset Configuration Words
- */
-#if defined(CONFIG_SYS_SBC_BOOT_LOW)
-# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS)
-#else
-# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (0)
-#endif /* defined(CONFIG_SYS_SBC_BOOT_LOW) */
-
-/* get the HRCW ISB field from CONFIG_SYS_IMMR */
-#define CONFIG_SYS_SBC_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) |\
- ((CONFIG_SYS_IMMR & 0x01000000) >> 7) |\
- ((CONFIG_SYS_IMMR & 0x00100000) >> 4) )
-
-#define CONFIG_SYS_HRCW_MASTER (HRCW_BPS11 |\
- HRCW_DPPC11 |\
- CONFIG_SYS_SBC_HRCW_IMMR |\
- HRCW_MMR00 |\
- HRCW_LBPC11 |\
- HRCW_APPC10 |\
- HRCW_CS10PC00 |\
- (CONFIG_SYS_SBC_MODCK_H & HRCW_MODCK_H1111) |\
- CONFIG_SYS_SBC_HRCW_BOOT_FLAGS)
-
-/* no slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent.
- */
-#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH0_BASE + 0x00F00000)
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
-
-#ifndef CONFIG_SYS_RAMBOOT
-# define CONFIG_ENV_IS_IN_FLASH 1
-
-# ifdef CONFIG_ENV_IN_OWN_SECT
-# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
-# define CONFIG_ENV_SECT_SIZE 0x40000
-# else
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE)
-# define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
-# define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */
-# endif /* CONFIG_ENV_IN_OWN_SECT */
-#else
-# define CONFIG_ENV_IS_IN_NVRAM 1
-# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-# define CONFIG_ENV_SIZE 0x200
-#endif /* CONFIG_SYS_RAMBOOT */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
-
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers 2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-#define CONFIG_SYS_HID0_INIT (/*HID0_ICE |*/\
- /*HID0_DCE |*/\
- HID0_ICFI |\
- HID0_DCI |\
- HID0_IFEM |\
- HID0_ABE)
-
-#define CONFIG_SYS_HID0_FINAL (/*HID0_ICE |*/\
- HID0_IFEM |\
- HID0_ABE |\
- HID0_EMCP)
-#define CONFIG_SYS_HID2 0
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RMR 0
-
-/*-----------------------------------------------------------------------
- * BCR - Bus Configuration 4-25
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_BCR (BCR_EBM |\
- BCR_PLDP |\
- BCR_EAV |\
- BCR_NPQM0)
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 4-31
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_SYS_SIUMCR (SIUMCR_L2CPC01 |\
- SIUMCR_APPC10 |\
- SIUMCR_CS10PC01)
-
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\
- SYPCR_BMT |\
- SYPCR_PBME |\
- SYPCR_LBME |\
- SYPCR_SWRI |\
- SYPCR_SWP)
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control 4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC |\
- TMCNTSC_ALR |\
- TMCNTSC_TCF |\
- TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR (PISCR_PS |\
- PISCR_PTF |\
- PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control 9-8
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SCCR (SCCR_DFBRG01)
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration 13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR 0
-
-/*
- * Init Memory Controller:
- *
- * Bank Bus Machine PortSz Device
- * ---- --- ------- ------ ------
- * 0 60x GPCM 64 bit FLASH (BGA - 16MB AMD AM29DL323DB90)
- * 1 60x SDRAM 64 bit SDRAM (BGA - 64MB Hitachi HM5225325FBP-B60)
- * 2 Local SDRAM 32 bit SDRAM (BGA - 32MB Hitachi HM5225325FBP-B60)
- * 3 unused
- * 4 60x GPCM 8 bit Board Regs, LEDs, switches
- * 5 unused
- * 6 unused
- * 7 unused
- * 8 PCMCIA
- * 9 unused
- * 10 unused
- * 11 unused
-*/
-
-/* Bank 0 - FLASH
- *
- */
-#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_DECC_NONE |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_6_CLK |\
- ORxG_EHTR)
-
-/* Bank 1 - SDRAM
- *
- */
-#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_SDRAM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI0_A8 |\
- ORxS_NUMR_12 |\
- ORxS_IBID)
-
-#define CONFIG_SYS_PSDMR 0x014DA412
-#define CONFIG_SYS_PSRT 0x79
-
-
-/* Bank 2 - SDRAM
- *
- */
-#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM1_BASE & BRx_BA_MSK) |\
- BRx_PS_32 |\
- BRx_MS_SDRAM_L |\
- BRx_V)
-
-#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM1_SIZE) |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI0_A9 |\
- ORxS_NUMR_12)
-
-#define CONFIG_SYS_LSDMR 0x0169A512
-#define CONFIG_SYS_LSRT 0x79
-
-#define CONFIG_SYS_MPTPR (0x0800 & MPTPR_PTP_MSK)
-
-/* Bank 4 - On board registers
- *
- */
-#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK) |\
- BRx_PS_8 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR4_PRELIM (ORxG_AM_MSK |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_5_CLK |\
- ORxG_TRLX)
-
-#endif /* __CONFIG_H */
projects / u-boot / commitdiff