E: ThomasF@hyperion-entertainment.com
D: Support for AmigaOne
-N: Niklaus Giger
-E: niklaus.giger@netstal.com
-D: Support for HCU(x) boards
-W: www.netstal.com
-
N: Paul Gortmaker
E: paul.gortmaker@windriver.com
D: Support for WRS SBC8347/8349 boards
WUH405 PPC405EP
CMS700 PPC405EP
-Niklaus Giger <niklaus.giger@netstal.com>
-
- HCU4 PPC405GPr
- MCU25 PPC405GPr
- HCU5 PPC440EPx
-
Siddarth Gore <gores@marvell.com>
guruplug ARM926EJS (Kirkwood SoC)
+++ /dev/null
-/*
- *(C) Copyright 2005-2008 Netstal Maschinen AG
- * Niklaus Giger (Niklaus.Giger@netstal.com)
- *
- * This source code is free software; you can redistribute it
- * and/or modify it in source code form under the terms of the GNU
- * General Public License as published by the Free Software
- * Foundation; either version 2 of the License, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA
- */
-
-#include <common.h>
-#include <asm/ppc4xx.h>
-#include <asm/processor.h>
-#include "nm.h"
-
-#if defined(DEBUG)
-void show_sdram_registers(void)
-{
- u32 value;
-
- printf("SDRAM Controller Registers --\n");
- mfsdram(SDRAM0_CFG, value);
- printf(" SDRAM0_CFG : 0x%08x\n", value);
- mfsdram(SDRAM0_STATUS, value);
- printf(" SDRAM0_STATUS: 0x%08x\n", value);
- mfsdram(SDRAM0_B0CR, value);
- printf(" SDRAM0_B0CR : 0x%08x\n", value);
- mfsdram(SDRAM0_B1CR, value);
- printf(" SDRAM0_B1CR : 0x%08x\n", value);
- mfsdram(SDRAM0_TR, value);
- printf(" SDRAM0_TR : 0x%08x\n", value);
- mfsdram(SDRAM0_RTR, value);
- printf(" SDRAM0_RTR : 0x%08x\n", value);
-}
-#endif
-
-long int init_ppc405_sdram(unsigned int dram_size)
-{
-#ifdef DEBUG
- printf(__FUNCTION__);
-#endif
- /* disable memory controller */
- mtsdram(SDRAM0_CFG, 0x00000000);
-
- udelay (500);
-
- /* Clear SDRAM0_BESR0 (Bus Error Syndrome Register) */
- mtsdram(SDRAM0_BESR0, 0xffffffff);
-
- /* Clear SDRAM0_BESR1 (Bus Error Syndrome Register) */
- mtsdram(SDRAM0_BESR1, 0xffffffff);
-
- /* Clear SDRAM0_ECCCFG (disable ECC) */
- mtsdram(SDRAM0_ECCCFG, 0x00000000);
-
- /* Clear SDRAM0_ECCESR (ECC Error Syndrome Register) */
- mtsdram(SDRAM0_ECCESR, 0xffffffff);
-
- /* Timing register: CASL=2, PTA=2, CTP=2, LDF=1, RFTA=5, RCD=2
- */
- mtsdram(SDRAM0_TR, 0x008a4015);
-
- /* Memory Bank 0 Config == BA=0x00000000, SZ=64M, AM=3, BE=1
- * and refresh timer
- */
- switch (dram_size >> 20) {
- case 32:
- mtsdram(SDRAM0_B0CR, 0x00062001);
- mtsdram(SDRAM0_RTR, 0x07F00000);
- break;
- case 64:
- mtsdram(SDRAM0_B0CR, 0x00084001);
- mtsdram(SDRAM0_RTR, 0x04100000);
- break;
- case 128:
- mtsdram(SDRAM0_B0CR, 0x000A4001);
- mtsdram(SDRAM0_RTR, 0x04100000);
- break;
- default:
- printf("Invalid memory size of %d MB given\n", dram_size >> 20);
- }
-
- /* Power management idle timer set to the default. */
- mtsdram(SDRAM0_PMIT, 0x07c00000);
-
- udelay (500);
-
- /* Enable banks (DCE=1, BPRF=1, ECCDD=1, EMDUL=1) TODO */
- mtsdram(SDRAM0_CFG, 0x90800000);
-
-#ifdef DEBUG
- printf("%s: done\n", __FUNCTION__);
-#endif
- return dram_size;
-}
+++ /dev/null
-/*
- *(C) Copyright 2005-2007 Netstal Maschinen AG
- * Niklaus Giger (Niklaus.Giger@netstal.com)
- *
- * This source code is free software; you can redistribute it
- * and/or modify it in source code form under the terms of the GNU
- * General Public License as published by the Free Software
- * Foundation; either version 2 of the License, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA
- */
-
-extern void hcu_led_set(u32 value);
-extern u32 get_serial_number(void);
-extern u32 hcu_get_slot(void);
-extern int board_with_pci(void);
-extern void nm_show_print(int generation, int index, int hw_capabilities);
-extern void set_params_for_sw_install(int install_requested, char *board_name );
-extern void common_misc_init_r(void);
-
-enum {
- /* HW_GENERATION_HCU1/2 is no longer supported */
- HW_GENERATION_HCU3 = 0x10,
- HW_GENERATION_HCU4 = 0x20,
- HW_GENERATION_HCU5 = 0x30,
- HW_GENERATION_MCU = 0x08,
- HW_GENERATION_MCU20 = 0x0a,
- HW_GENERATION_MCU25 = 0x09,
-};
-
-#ifdef CONFIG_405GP
-#if defined(DEBUG)
-void show_sdram_registers(void);
-#endif
-long int init_ppc405_sdram(unsigned int dram_size);
-#endif
+++ /dev/null
-/*
- *(C) Copyright 2005-2008 Netstal Maschinen AG
- * Niklaus Giger (Niklaus.Giger@netstal.com)
- *
- * This source code is free software; you can redistribute it
- * and/or modify it in source code form under the terms of the GNU
- * General Public License as published by the Free Software
- * Foundation; either version 2 of the License, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA
- */
-
-#include <common.h>
-#include <command.h>
-#include <net.h>
-#include "nm.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define DEFAULT_ETH_ADDR "ethaddr"
-
-typedef struct {u8 id; char *name;} generation_info;
-
-generation_info generations[6] = {
- {HW_GENERATION_HCU3, "HCU3"},
- {HW_GENERATION_HCU4, "HCU4"},
- {HW_GENERATION_HCU5, "HCU5"},
- {HW_GENERATION_MCU, "MCU"},
- {HW_GENERATION_MCU20, "MCU20"},
- {HW_GENERATION_MCU25, "MCU25"},
-};
-
-void nm_show_print(int generation, int index, int hw_capabilities)
-{
- int j;
- char *generationName=0;
-
- /* reset ANSI terminal color mode */
- printf("\x1B""[0m""Netstal Maschinen AG: ");
- for (j=0; j < (sizeof(generations)/sizeof(generations[0])); j++) {
- if (generations[j].id == generation) {
- generationName = generations[j].name;
- break;
- }
- }
- printf("%s: index %d HW 0x%x\n", generationName, index, hw_capabilities);
- for (j = 0;j < 6; j++) {
- hcu_led_set(1 << j);
- udelay(200 * 1000);
- }
-}
-
-void set_params_for_sw_install(int install_requested, char *board_name )
-{
- if (install_requested) {
- char string[128];
-
- printf("\n\n%s SW-Installation: %d patching boot parameters\n",
- board_name, install_requested);
- setenv("bootdelay", "0");
- setenv("loadaddr", "0x01000000");
- setenv("serverip", "172.25.1.1");
- setenv("bootcmd", "run install");
- sprintf(string, "tftp ${loadaddr} admin/sw_on_hd; "
- "tftp ${loadaddr} installer/%s_sw_inst; "
- "run boot_sw_inst", board_name);
- setenv("install", string);
- sprintf(string, "setenv bootargs emac(0,0)c:%s/%s_sw_inst "
- "e=${ipaddr} h=${serverip} f=0x1000; "
- "bootvx ${loadaddr}%c",
- board_name, board_name, 0);
- setenv("boot_sw_inst", string);
- }
-}
-
-void common_misc_init_r(void)
-{
- IPaddr_t ipaddr;
- char *ipstring;
- uchar ethaddr[6];
-
- if (!eth_getenv_enetaddr(DEFAULT_ETH_ADDR, ethaddr)) {
- /* Must be in sync with CONFIG_ETHADDR */
- u32 serial = get_serial_number();
- ethaddr[0] = 0x00;
- ethaddr[1] = 0x60;
- ethaddr[2] = 0x13;
- ethaddr[3] = (serial >> 16) & 0xff;
- ethaddr[4] = (serial >> 8) & 0xff;
- ethaddr[5] = hcu_get_slot();
- eth_setenv_enetaddr(DEFAULT_ETH_ADDR, ethaddr);
- }
-
- /* IP-Adress update */
- ipstring = getenv("ipaddr");
- if (ipstring == 0)
- ipaddr = string_to_ip("172.25.1.99");
- else
- ipaddr = string_to_ip(ipstring);
- if ((ipaddr & 0xff) != (32 + hcu_get_slot())) {
- char tmp[22];
-
- ipaddr = (ipaddr & 0xffffff00) + 32 + hcu_get_slot();
- ip_to_string (ipaddr, tmp);
- printf("%s: enforce %s\n", __FUNCTION__, tmp);
- setenv("ipaddr", tmp);
- saveenv();
- }
-}
+++ /dev/null
-#
-# (C) Copyright 2007-2008 Netstal Maschinen AG
-# Niklaus Giger (ng@netstal.com)
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-ifneq ($(OBJTREE),$(SRCTREE))
-$(shell mkdir -p $(obj)../common)
-endif
-
-LIB = $(obj)lib$(BOARD).o
-
-COBJS = $(BOARD).o \
- ../common/fixed_sdram.o \
- ../common/nm_bsp.o
-
-SRCS := $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-
-$(LIB): $(OBJS)
- $(call cmd_link_o_target, $^)
-
-clean:
- rm -f $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
+++ /dev/null
-HCU4 Configuration Details
-
-Memory Bank 0 -- Flash chip
----------------------------
-
-0xfff00000 - 0xffffffff
-
-The flash chip is really only 512Kbytes, but the high address bit of
-the 1Meg region is ignored, so the flash is replicated through the
-region. Thus, this is consistent with a flash base address 0xfff80000.
-
-The placement at the end is to be consistent with reset behavior,
-where the processor itself initially uses this bus to load the branch
-vector and start running.
-
-On-Chip Memory
---------------
-
-0xf4000000 - 0xf4000fff
-
-The 405GPr includes a 4K on-chip memory that can be placed however
-software chooses. I choose to place the memory at this address, to
-keep it out of the cachable areas.
-
-
-Internal Peripherals
---------------------
-
-0xef600300 - 0xef6008ff
-
-These are scattered various peripherals internal to the PPC405GPr
-chip.
-
-Chip-Select 2: Flash Memory
----------------------------
-
-0x70000000
-
-Chip-Select 3: CAN Interface
-----------------------------
-0x7800000
-
-
-Chip-Select 4: IMC-bus standard
--------------------------------
-
-Our IO-Bus (slow version)
-
-
-Chip-Select 5: IMC-bus fast (inactive)
---------------------------------------
-
-Our IO-Bus (fast, but not yet use)
-
-
-Memory Bank 1 -- SDRAM
--------------------------------------
-
-0x00000000 - 0x1ffffff # Default 32 MB
+++ /dev/null
-#
-# (C) Copyright 2005 Netstal Maschinen AG
-# Niklaus Giger (ng@netstal.com)
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-#
-# Netstal Maschinen AG: HCU4 boards
-#
-ifeq ($(debug),1)
-PLATFORM_CPPFLAGS += -DDEBUG -g
-endif
+++ /dev/null
-/*
- *(C) Copyright 2005-2008 Netstal Maschinen AG
- * Niklaus Giger (Niklaus.Giger@netstal.com)
- *
- * This source code is free software; you can redistribute it
- * and/or modify it in source code form under the terms of the GNU
- * General Public License as published by the Free Software
- * Foundation; either version 2 of the License, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA
- */
-
-#include <common.h>
-#include <asm/ppc4xx.h>
-#include <asm/processor.h>
-#include <asm/io.h>
-#include <asm/u-boot.h>
-#include "../common/nm.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define HCU_MACH_VERSIONS_REGISTER (0x7C000000 + 0xF00000)
-#define HCU_SLOT_ADDRESS (0x7C000000 + 0x400000)
-#define HCU_DIGITAL_IO_REGISTER (0x7C000000 + 0x500000)
-#define HCU_SW_INSTALL_REQUESTED 0x10
-
-/*
- * This function is run very early, out of flash, and before devices are
- * initialized. It is called by arch/powerpc/lib/board.c:board_init_f by virtue
- * of being in the init_sequence array.
- *
- * The SDRAM has been initialized already -- start.S:start called
- * init.S:init_sdram early on -- but it is not yet being used for
- * anything, not even stack. So be careful.
- */
-
-/* Attention: If you want 1 microsecs times from the external oscillator
- * 0x00004051 is okay for u-boot/linux, but different from old vxworks values
- * 0x00804051 causes problems with u-boot and linux!
- */
-#define CPC0_CR0_VALUE 0x0030103c
-#define CPC0_CR1_VALUE 0x00004051
-
-int board_early_init_f (void)
-{
- /*
- * Interrupt controller setup for the HCU4 board.
- * Note: IRQ 0-15 405GP internally generated; high; level sensitive
- * IRQ 16 405GP internally generated; low; level sensitive
- * IRQ 17-24 RESERVED/UNUSED
- * IRQ 31 (EXT IRQ 6) (unused)
- */
- mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
- mtdcr(UIC0ER, 0x00000000); /* disable all ints */
- mtdcr(UIC0CR, 0x00000000); /* set all to be non-critical */
- mtdcr(UIC0PR, 0xFFFFE000); /* set int polarities */
- mtdcr(UIC0TR, 0x00000000); /* set int trigger levels */
- mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
-
- mtdcr(CPC0_CR1, CPC0_CR1_VALUE);
- mtdcr(CPC0_ECR, 0x60606000);
- mtdcr(CPC0_EIRR, 0x7C000000);
-
- return 0;
-}
-
-#ifdef CONFIG_BOARD_PRE_INIT
-int board_pre_init (void)
-{
- return board_early_init_f ();
-}
-#endif
-
-int sys_install_requested(void)
-{
- u16 ioValue = in_be16((u16 *)HCU_DIGITAL_IO_REGISTER);
- return (ioValue & HCU_SW_INSTALL_REQUESTED) != 0;
-}
-
-int checkboard (void)
-{
- u16 boardVersReg = in_be16((u16 *)HCU_MACH_VERSIONS_REGISTER);
- u16 generation = boardVersReg & 0xf0;
- u16 index = boardVersReg & 0x0f;
-
- /* Cannot be done in board_early_init */
- mtdcr(CPC0_CR0, CPC0_CR0_VALUE);
-
- /* Force /RTS to active. The board it not wired quite
- * correctly to use cts/rtc flow control, so just force the
- * /RST active and forget about it.
- */
- writeb (readb (0xef600404) | 0x03, 0xef600404);
- nm_show_print(generation, index, 0);
-
- return 0;
-}
-
-u32 hcu_led_get(void)
-{
- return (~(in_be32((u32 *)GPIO0_OR)) >> 23) & 0xff;
-}
-
-/*
- * hcu_led_set value to be placed into the LEDs (max 6 bit)
- */
-void hcu_led_set(u32 value)
-{
- u32 tmp = ~value;
-
- tmp = (tmp << 23) | 0x7FFFFF;
- out_be32((u32 *)GPIO0_OR, tmp);
-}
-
-/*
- * hcu_get_slot
- */
-u32 hcu_get_slot(void)
-{
- u16 slot = in_be16((u16 *)HCU_SLOT_ADDRESS);
- return slot & 0x7f;
-}
-
-/*
- * get_serial_number
- */
-u32 get_serial_number(void)
-{
- u32 serial = in_be32((u32 *)CONFIG_SYS_FLASH_BASE);
-
- if (serial == 0xffffffff)
- return 0;
-
- return serial;
-}
-
-
-/*
- * misc_init_r.
- */
-
-int misc_init_r(void)
-{
- common_misc_init_r();
- set_params_for_sw_install( sys_install_requested(), "hcu4" );
- return 0;
-}
-
-phys_size_t initdram(int board_type)
-{
- long dram_size = 0;
- u16 boardVersReg = in_be16((u16 *)HCU_MACH_VERSIONS_REGISTER);
- u16 generation = boardVersReg & 0xf0;
- u16 index = boardVersReg & 0x0f;
-
- if (generation == HW_GENERATION_HCU3 && index < 0xf)
- dram_size = 32 << 20; /* 32 MB - RAM */
- else
- dram_size = 64 << 20; /* 64 MB - RAM */
- init_ppc405_sdram(dram_size);
-
-#ifdef DEBUG
- show_sdram_registers();
-#endif
-
- return dram_size;
-}
-
-#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
-void ft_board_setup(void *blob, bd_t *bd)
-{
- ft_cpu_setup(blob, bd);
-
-}
-#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
-
-/*
- * Hardcoded flash setup:
- * Flash 0 is a non-CFI AMD AM29F040 flash, 8 bit flash / 8 bit bus.
- */
-ulong board_flash_get_legacy (ulong base, int banknum, flash_info_t * info)
-{
- if (banknum == 0) { /* non-CFI boot flash */
- info->portwidth = 1;
- info->chipwidth = 1;
- info->interface = FLASH_CFI_X8;
- return 1;
- } else
- return 0;
-}
+++ /dev/null
-#
-# (C) Copyright 2007-2008 Netstal Maschinen AG
-# Niklaus Giger (ng@netstal.com)
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-ifneq ($(OBJTREE),$(SRCTREE))
-$(shell mkdir -p $(obj)../common)
-endif
-
-LIB = $(obj)lib$(BOARD).o
-
-COBJS = $(BOARD).o \
- sdram.o \
- ../common/nm_bsp.o
-SOBJS = init.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-all: $(LIB) $(SOBJS)
-
-$(LIB): $(OBJS)
- $(call cmd_link_o_target, $^)
-
-clean:
- rm -f $(SOBJS) $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
+++ /dev/null
-HCU5 configuration details and startup sequence
-
-(C) Copyright 2007 Netstal Maschinen AG
- Niklaus Giger (Niklaus.Giger@netstal.com)
-
-TODO:
------
-- Fix error: Waiting for PHY auto negotiation to complete..... TIMEOUT !
- - Does not occur if both EMAC are connected
-- Fix RTS/CTS problem (HW?)
- CONFIG_SERIAL_MULTI/CONFIG_SERIAL_SOFTWARE_FIFO hangs after
- Switching to interrupt driven serial input mode
-
-Caveats:
---------
-Errata CHIP_8: Incorrect Write to DDR SDRAM. (was not applied to sequoia.c)
-see hcu5.c.
-
-
-Memory Bank 0 -- Flash chip
----------------------------
-
-0xfff00000 - 0xffffffff
-
-The flash chip is really only 512Kbytes, but the high address bit of
-the 1Meg region is ignored, so the flash is replicated through the
-region. Thus, this is consistent with a flash base address 0xfff80000.
-
-The placement at the end is to be consistent with reset behavior,
-where the processor itself initially uses this bus to load the branch
-vector and start running.
-
-On-Chip Memory
---------------
-
-0xe0010000- 0xe0013fff CONFIG_SYS_OCM_BASE
-The 440EPx includes a 16K on-chip memory that can be placed however
-software chooses.
-
-Internal Peripherals
---------------------
-
-0xef600300 - 0xef6008ff
-
-These are scattered various peripherals internal to the PPC440EPX
-chip.
-
-Chip-Select 2: Flash Memory
----------------------------
-
-Not used
-
-Chip-Select 3: CAN Interface
-----------------------------
-0xc800000: 2 Intel 82527 CAN-Controller
-
-
-Chip-Select 4: IMC-bus standard
--------------------------------
-
-0xcc00000: Netstal specific IO-Bus
-
-
-Chip-Select 5: IMC-bus fast (inactive)
---------------------------------------
-
-0xce00000: Netstal specific IO-Bus (fast, but not yet used)
-
-
-Memory Bank 1 -- DDR2
--------------------------------------
-
-0x00000000 - 0xfffffff # Default 256 MB
-
-PCI ??
-
-USB ??
-Only USB_STORAGE is enabled to load vxWorks
-from a memory stick.
-
-System-LEDs ??? (Analog zu HCU4 ???)
-
-Startup sequence
-----------------
-
-(arch/powerpc/cpu/ppc4xx/resetvec.S)
-depending on configs option
-call _start_440 _start_pci oder _start
-
-(arch/powerpc/cpu/ppc4xx/start.S)
-
-_start_440:
- initialize register like
- CCR0
- debug
- setup interrupt vectors
- configure cache regions
- clear and setup TLB
- enable internal RAM
- jump start_ram
- which in turn will jump to start
-_start:
- Clear and set up some registers.
- Debug setup
- Setup the internal SRAM
- Setup the stack in internal SRAM
- setup stack pointer (r1)
- setup GOT
- call cpu_init_f /* run low-level CPU init code (from Flash) */
-
- call cpu_init_f
- board_init_f: (arch/powerpc/lib\board.c)
- init_sequence defines a list of function to be called
- board_early_init_f: (board/netstal/hcu5/hcu5.c)
- We are using Bootstrap-Option A
- if CPR0_ICFG_RLI_MASK == 0 then set some registers and reboot
- Setup the GPIO pins
- Setup the interrupt controller polarities, triggers, etc.
- Ethernet, PCI, USB enable
- setup BOOT FLASH (Chip timing)
- init_baudrate,
- serial_init
- checkcpu
- misc_init_f #ifdef
- init_func_i2c #ifdef
- post_init_f #ifdef
- init_func_ram -> calls init_dram board/netstal/hcu5/sdram.c
- (EYE function removed!!)
- test_dram call
-
- * Reserve memory at end of RAM for (top down in that order):
- * - kernel log buffer
- * - protected RAM
- * - LCD framebuffer
- * - monitor code
- * - board info struct
- Save local variables to board info struct
- call relocate_code() does not return
- relocate_code: (arch/powerpc/cpu/ppc4xx/start.S)
--------------------------------------------------------
-From now on our copy is in RAM and we will run from there,
- starting with board_init_r
--------------------------------------------------------
- board_init_r: (arch/powerpc/lib\board.c)
- setup bd function pointers
- trap_init
- flash_init: (board/netstal/hcu5/flash.c)
- /* setup for u-boot erase, update */
- setup bd flash info
- cpu_init_r: (arch/powerpc/cpu/ppc4xx/cpu_init.c)
- peripheral chip select in using defines like
- CONFIG_SYS_EBC_PB0A, CONFIG_SYS_EBC_PB0C from hcu5.h
- mem_malloc_init
- malloc_bin_reloc
- spi_init (r or f)??? (CONFIG_ENV_IS_IN_EEPROM)
- env_relocated
- misc_init_r(bd): (board/netstal/hcu5.c)
- ethaddr mit serial number ergänzen
- Then we will somehow go into the command loop
-
-Most of the HW specific code for the HCU5 may be found in
-include/configs/hcu5.h
-board/netstal/hcu5/*
-arch/powerpc/cpu/ppc4xx/*
-arch/powerpc/lib/*
-include/ppc440.h
-
-Drivers for serial etc are found under drivers/
-
-Don't ask question if you did not look at the README !!
-Most CONFIG_SYS_* and CONFIG_* switches are mentioned/explained there.
+++ /dev/null
-#
-# (C) Copyright 2005 Netstal Maschinen AG
-# Niklaus Giger (ng@netstal.com)
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-#
-# Netstal Maschinen AG: HCU5 boards
-#
-PLATFORM_CPPFLAGS += -DCONFIG_440=1
-
-ifeq ($(debug),1)
-PLATFORM_CPPFLAGS += -DDEBUG -g
-endif
+++ /dev/null
-/*
- *(C) Copyright 2005-2008 Netstal Maschinen AG
- * Niklaus Giger (Niklaus.Giger@netstal.com)
- *
- * This source code is free software; you can redistribute it
- * and/or modify it in source code form under the terms of the GNU
- * General Public License as published by the Free Software
- * Foundation; either version 2 of the License, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA
- */
-
-#include <common.h>
-#include <asm/processor.h>
-#include <asm/ppc440.h>
-#include <asm/io.h>
-#include <asm/4xx_pci.h>
-
-#include "../common/nm.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-#undef BOOTSTRAP_OPTION_A_ACTIVE
-
-#define SDR0_CP440 0x0180
-
-#define SYSTEM_RESET 0x30000000
-#define CHIP_RESET 0x20000000
-
-#define SDR0_ECID0 0x0080
-#define SDR0_ECID1 0x0081
-#define SDR0_ECID2 0x0082
-#define SDR0_ECID3 0x0083
-
-#define SYS_IO_ADDRESS (CONFIG_SYS_CS_2 + 0x00e00000)
-#define SYS_SLOT_ADDRESS (CONFIG_SYS_CPLD + 0x00400000)
-#define HCU_DIGITAL_IO_REGISTER (CONFIG_SYS_CPLD + 0x0500000)
-#define HCU_SW_INSTALL_REQUESTED 0x10
-
-/*
- * This function is run very early, out of flash, and before devices are
- * initialized. It is called by arch/powerpc/lib/board.c:board_init_f by virtue
- * of being in the init_sequence array.
- *
- * The SDRAM has been initialized already -- start.S:start called
- * init.S:init_sdram early on -- but it is not yet being used for
- * anything, not even stack. So be careful.
- */
-
-int board_early_init_f(void)
-{
-
-#ifdef BOOTSTRAP_OPTION_A_ACTIVE
- /* Booting with Bootstrap Option A
- * First boot, with CPR0_ICFG_RLI_MASK == 0
- * no we setup varios boot strapping register,
- * then we do reset the PPC440 using a chip reset
- * Unfortunately, we cannot use this option, as Nto1 is not set
- * with Bootstrap Option A and cannot be changed later on by SW
- * There are no other possible boostrap options with a 8 bit ROM
- * See Errata (Version 1.04) CHIP_9
- */
-
- u32 cpr0icfg;
- u32 dbcr;
-
- mfcpr(CPR0_ICFG, cpr0icfg);
- if (!(cpr0icfg & CPR0_ICFG_RLI_MASK)) {
- mtcpr(CPR0_MALD, 0x02000000);
- mtcpr(CPR0_OPBD, 0x02000000);
- mtcpr(CPR0_PERD, 0x05000000); /* 1:5 */
- mtcpr(CPR0_PLLC, 0x40000238);
- mtcpr(CPR0_PLLD, 0x01010414);
- mtcpr(CPR0_PRIMAD, 0x01000000);
- mtcpr(CPR0_PRIMBD, 0x01000000);
- mtcpr(CPR0_SPCID, 0x03000000);
- mtsdr(SDR0_PFC0, 0x00003E00); /* [CTE] = 0 */
- mtsdr(SDR0_CP440, 0x0EAAEA02); /* [Nto1] = 1*/
- mtcpr(CPR0_ICFG, cpr0icfg | CPR0_ICFG_RLI_MASK);
-
- /*
- * Initiate system reset in debug control register DBCR
- */
- dbcr = mfspr(SPRN_DBCR0);
- mtspr(SPRN_DBCR0, dbcr | CHIP_RESET);
- }
- mtsdr(SDR0_CP440, 0x0EAAEA02); /* [Nto1] = 1*/
-#endif
- mtdcr(EBC0_CFGADDR, EBC0_CFG);
- mtdcr(EBC0_CFGDATA, 0xb8400000);
-
- /*
- * Setup the GPIO pins
- */
- out32(GPIO0_OR, 0x00000000);
- out32(GPIO0_TCR, 0x7C2FF1CF);
- out32(GPIO0_OSRL, 0x40055000);
- out32(GPIO0_OSRH, 0x00000000);
- out32(GPIO0_TSRL, 0x40055000);
- out32(GPIO0_TSRH, 0x00000400);
- out32(GPIO0_ISR1L, 0x40000000);
- out32(GPIO0_ISR1H, 0x00000000);
- out32(GPIO0_ISR2L, 0x00000000);
- out32(GPIO0_ISR2H, 0x00000000);
- out32(GPIO0_ISR3L, 0x00000000);
- out32(GPIO0_ISR3H, 0x00000000);
-
- out32(GPIO1_OR, 0x00000000);
- out32(GPIO1_TCR, 0xC6007FFF);
- out32(GPIO1_OSRL, 0x00140000);
- out32(GPIO1_OSRH, 0x00000000);
- out32(GPIO1_TSRL, 0x00000000);
- out32(GPIO1_TSRH, 0x00000000);
- out32(GPIO1_ISR1L, 0x05415555);
- out32(GPIO1_ISR1H, 0x40000000);
- out32(GPIO1_ISR2L, 0x00000000);
- out32(GPIO1_ISR2H, 0x00000000);
- out32(GPIO1_ISR3L, 0x00000000);
- out32(GPIO1_ISR3H, 0x00000000);
-
- /*
- * Setup the interrupt controller polarities, triggers, etc.
- */
- mtdcr(UIC0SR, 0xffffffff); /* clear all */
- mtdcr(UIC0ER, 0x00000000); /* disable all */
- mtdcr(UIC0CR, 0x00000005); /* ATI & UIC1 crit are critical */
- mtdcr(UIC0PR, 0xfffff7ff); /* per ref-board manual */
- mtdcr(UIC0TR, 0x00000000); /* per ref-board manual */
- mtdcr(UIC0VR, 0x00000000); /* int31 highest, base=0x000 */
- mtdcr(UIC0SR, 0xffffffff); /* clear all */
-
- mtdcr(UIC1SR, 0xffffffff); /* clear all */
- mtdcr(UIC1ER, 0x00000000); /* disable all */
- mtdcr(UIC1CR, 0x00000000); /* all non-critical */
- mtdcr(UIC1PR, 0xffffffff); /* per ref-board manual */
- mtdcr(UIC1TR, 0x00000000); /* per ref-board manual */
- mtdcr(UIC1VR, 0x00000000); /* int31 highest, base=0x000 */
- mtdcr(UIC1SR, 0xffffffff); /* clear all */
-
- mtdcr(UIC2SR, 0xffffffff); /* clear all */
- mtdcr(UIC2ER, 0x00000000); /* disable all */
- mtdcr(UIC2CR, 0x00000000); /* all non-critical */
- mtdcr(UIC2PR, 0xffffffff); /* per ref-board manual */
- mtdcr(UIC2TR, 0x00000000); /* per ref-board manual */
- mtdcr(UIC2VR, 0x00000000); /* int31 highest, base=0x000 */
- mtdcr(UIC2SR, 0xffffffff); /* clear all */
- mtsdr(SDR0_PFC0, 0x00003E00); /* Pin function: */
- mtsdr(SDR0_PFC1, 0x00848000); /* Pin function: UART0 has 4 pins */
-
- /* setup BOOT FLASH */
- mtsdr(SDR0_CUST0, 0xC0082350);
-
- return 0;
-}
-
-#ifdef CONFIG_BOARD_PRE_INIT
-int board_pre_init(void)
-{
- return board_early_init_f();
-}
-
-#endif
-
-int sys_install_requested(void)
-{
- u16 *ioValuePtr = (u16 *)HCU_DIGITAL_IO_REGISTER;
- return (in_be16(ioValuePtr) & HCU_SW_INSTALL_REQUESTED) != 0;
-}
-
-int checkboard(void)
-{
- u16 *hwVersReg = (u16 *) HCU_HW_VERSION_REGISTER;
- u16 *boardVersReg = (u16 *) HCU_CPLD_VERSION_REGISTER;
- u16 generation = in_be16(boardVersReg) & 0xf0;
- u16 index = in_be16(boardVersReg) & 0x0f;
- u32 ecid0, ecid1, ecid2, ecid3;
-
- nm_show_print(generation, index, in_be16(hwVersReg) & 0xff);
- mfsdr(SDR0_ECID0, ecid0);
- mfsdr(SDR0_ECID1, ecid1);
- mfsdr(SDR0_ECID2, ecid2);
- mfsdr(SDR0_ECID3, ecid3);
-
- printf("Chip ID 0x%x 0x%x 0x%x 0x%x\n", ecid0, ecid1, ecid2, ecid3);
-
- return 0;
-}
-
-u32 hcu_led_get(void)
-{
- return in16(SYS_IO_ADDRESS) & 0x3f;
-}
-
-/*
- * hcu_led_set value to be placed into the LEDs (max 6 bit)
- */
-void hcu_led_set(u32 value)
-{
- out16(SYS_IO_ADDRESS, value);
-}
-
-/*
- * get_serial_number
- */
-u32 get_serial_number(void)
-{
- u32 *serial = (u32 *)CONFIG_SYS_FLASH_BASE;
-
- if (in_be32(serial) == 0xffffffff)
- return 0;
-
- return in_be32(serial);
-}
-
-
-/*
- * hcu_get_slot
- */
-u32 hcu_get_slot(void)
-{
- u16 *slot = (u16 *)SYS_SLOT_ADDRESS;
- return in_be16(slot) & 0x7f;
-}
-
-
-/*
- * misc_init_r.
- */
-int misc_init_r(void)
-{
- unsigned long usb2d0cr = 0;
- unsigned long usb2phy0cr, usb2h0cr = 0;
- unsigned long sdr0_pfc1;
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* Monitor protection ON by default */
- (void)flash_protect(FLAG_PROTECT_SET,
- -CONFIG_SYS_MONITOR_LEN,
- 0xffffffff,
- &flash_info[0]);
-
-#ifdef CONFIG_ENV_ADDR_REDUND
- /* Env protection ON by default */
- (void)flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR_REDUND,
- CONFIG_ENV_ADDR_REDUND + 2*CONFIG_ENV_SECT_SIZE - 1,
- &flash_info[0]);
-#endif
-#endif
-
- /*
- * USB stuff...
- */
-
- /* SDR Setting */
- mfsdr(SDR0_PFC1, sdr0_pfc1);
- mfsdr(SDR0_USB2D0CR, usb2d0cr);
- mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
- mfsdr(SDR0_USB2H0CR, usb2h0cr);
-
- usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK;
- usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; /*0*/
- usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK;
- usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ; /*1*/
- usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK;
- usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS; /*0*/
- usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK;
- usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST; /*1*/
- usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK;
- usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST; /*1*/
-
- /* An 8-bit/60MHz interface is the only possible alternative
- * when connecting the Device to the PHY
- */
- usb2h0cr = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK;
- usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ; /*1*/
-
- /* To enable the USB 2.0 Device function through the UTMI interface */
- usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK;
- usb2d0cr = usb2d0cr | SDR0_USB2D0CR_USB2DEV_SELECTION; /*1*/
-
- sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK;
- sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_USB2D_SEL; /*0*/
-
- mtsdr(SDR0_PFC1, sdr0_pfc1);
- mtsdr(SDR0_USB2D0CR, usb2d0cr);
- mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
- mtsdr(SDR0_USB2H0CR, usb2h0cr);
-
- /*clear resets*/
- udelay(1000);
- mtsdr(SDR0_SRST1, 0x00000000);
- udelay(1000);
- mtsdr(SDR0_SRST0, 0x00000000);
- printf("USB: Host(int phy) Device(ext phy)\n");
-
- common_misc_init_r();
- set_params_for_sw_install( sys_install_requested(), "hcu5" );
- /* We cannot easily enable trace before, as there are other
- * routines messing around with sdr0_pfc1. And I do not need it.
- */
- if (mfspr(SPRN_DBCR0) & 0x80000000) {
- /* External debugger alive
- * enable trace facilty for Lauterbach
- * CCR0[DTB]=0 Enable broadcast of trace information
- * SDR0_PFC0[TRE] Trace signals are enabled instead of
- * GPIO49-63
- */
- mtspr(SPRN_CCR0, mfspr(SPRN_CCR0) &~ (CCR0_DTB));
- mtsdr(SDR0_PFC0, sdr0_pfc1 | SDR0_PFC0_TRE_ENABLE);
- }
- return 0;
-}
-#ifdef CONFIG_PCI
-int board_with_pci(void)
-{
- u32 reg;
-
- mfsdr(SDR0_PCI0, reg);
- return (reg & SDR0_PCI0_PAE_MASK);
-}
-
-/*
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- */
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long addr;
-
- if (!board_with_pci()) { return 0; }
-
- /*
- * Set priority for all PLB3 devices to 0.
- * Set PLB3 arbiter to fair mode.
- */
- mfsdr(SDR0_AMP1, addr);
- mtsdr(SDR0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB3A0_ACR);
- mtdcr(PLB3A0_ACR, addr | 0x80000000); /* Sequoia */
-
- /*
- * Set priority for all PLB4 devices to 0.
- */
- mfsdr(SDR0_AMP0, addr);
- mtsdr(SDR0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB4A0_ACR) | 0xa0000000; /* Was 0x8---- */
- mtdcr(PLB4A0_ACR, addr); /* Sequoia */
-
- /*
- * As of errata version 0.4, CHIP_8: Incorrect Write to DDR SDRAM.
- * Workaround: Disable write pipelining to DDR SDRAM by setting
- * PLB4A0_ACR[WRP] = 0.
- */
- mtdcr(PLB4A0_ACR, 0); /* PATCH HAB: WRITE PIPELINING OFF */
-
- /* Segment1 */
- mtdcr(PLB4A1_ACR, 0); /* PATCH HAB: WRITE PIPELINING OFF */
-
- return board_with_pci();
-}
-
-/*
- * Override weak default pci_master_init()
- */
-void pci_master_init(struct pci_controller *hose)
-{
- if (!board_with_pci())
- return;
-
- __pci_master_init(hose);
-}
-#endif /* defined(CONFIG_PCI) */
-
-#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
-void ft_board_setup(void *blob, bd_t *bd)
-{
- ft_cpu_setup(blob, bd);
-
-}
-#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
-
-/*
- * Hardcoded flash setup:
- * Flash 0 is a non-CFI AMD AM29F040 flash, 8 bit flash / 8 bit bus.
- */
-ulong board_flash_get_legacy (ulong base, int banknum, flash_info_t * info)
-{
- if (banknum == 0) { /* non-CFI boot flash */
- info->portwidth = 1;
- info->chipwidth = 1;
- info->interface = FLASH_CFI_X8;
- return 1;
- } else
- return 0;
-}
+++ /dev/null
-/*
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <ppc_asm.tmpl>
-#include <config.h>
-#include <asm/mmu.h>
-
-/**************************************************************************
- * TLB TABLE
- *
- * This table is used by the cpu boot code to setup the initial tlb
- * entries. Rather than make broad assumptions in the cpu source tree,
- * this table lets each board set things up however they like.
- *
- * Pointer to the table is returned in r1
- *
- *************************************************************************/
- .section .bootpg,"ax"
- .globl tlbtab
-
-tlbtab:
- tlbtab_start
-
- /* TLB#0: vxWorks needs this entry for the Machine Check interrupt, */
- tlbentry( 0x40000000, SZ_256M, 0, 0, AC_RWX | SA_IG )
- /* TLB#1: TLB-entry for DDR SDRAM (Up to 2GB) */
- tlbentry( CONFIG_SYS_SDRAM_BASE, SZ_256M, CONFIG_SYS_SDRAM_BASE, 0,
- AC_RWX | SA_IG )
-
- /* TLB#2: TLB-entry for EBC */
- tlbentry( 0x80000000, SZ_256M, 0x80000000, 1, AC_RWX | SA_IG)
-
- /*
- * TLB#3: BOOT_CS (FLASH) must be forth. Before relocation SA_I can be
- * off to use the speed up boot process. It is patched after relocation
- * to enable SA_I
- */
- tlbentry( CONFIG_SYS_BOOT_BASE_ADDR, SZ_1M, CONFIG_SYS_BOOT_BASE_ADDR, 1,
- AC_RWX | SA_G)
-
- /*
- * TLB entries for SDRAM are not needed on this platform.
- * They are dynamically generated in the SPD DDR(2) detection
- * routine.
- */
-
- /* TLB#4: */
- tlbentry( CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 1,
- AC_RW | SA_IG )
- /* TLB#5: */
- tlbentry( CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 1,
- AC_RW | SA_IG )
- /* TLB#6: */
- tlbentry( CONFIG_SYS_PCI_MEMBASE3, SZ_256M, CONFIG_SYS_PCI_MEMBASE3, 1,
- AC_RW | SA_IG )
-
- /* TLB-entry for Internal Registers & OCM */
- /* TLB#7: */
- tlbentry( 0xe0000000, SZ_16M, 0xe0000000, 0,
- AC_RWX | SA_IG )
-
- /*TLB-entry PCI registers*/
- /* TLB#8: */
- tlbentry( 0xEEC00000, SZ_1K, 0xEEC00000, 1, AC_RWX | SA_IG )
-
- /* TLB-entry for peripherals */
- /* TLB#9: */
- tlbentry( 0xEF000000, SZ_16M, 0xEF000000, 1, AC_RWX | SA_IG)
-
- /* CAN */
- /* TLB#10: */
- tlbentry( CONFIG_SYS_CS_1, SZ_1K, CONFIG_SYS_CS_1, 1, AC_RWX | SA_IG )
-
- /* TLB#11: CPLD and IMC-Standard 32 MB */
- tlbentry( CONFIG_SYS_CS_2, SZ_16M, CONFIG_SYS_CS_2, 1, AC_RWX | SA_IG )
-
- /* TLB#12: */
- tlbentry( CONFIG_SYS_CS_2 + 0x1000000, SZ_16M, CONFIG_SYS_CS_2 + 0x1000000, 1,
- AC_RWX | SA_IG )
-
- /* IMC-Fast 32 MB */
- /* TLB#13: */
- tlbentry( CONFIG_SYS_CS_3, SZ_16M, CONFIG_SYS_CS_3, 1, AC_RWX | SA_IG )
- /* TLB#14: */
- tlbentry( CONFIG_SYS_CS_3 + 0x1000000, SZ_16M, CONFIG_SYS_CS_3, 1,
- AC_RWX | SA_IG )
-
- tlbtab_end
+++ /dev/null
-/*
- * (C) Copyright 2007
- * Niklaus Giger (Niklaus.Giger@netstal.com)
- * (C) Copyright 2006
- * Sylvie Gohl, AMCC/IBM, gohl.sylvie@fr.ibm.com
- * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
- * Thierry Roman, AMCC/IBM, thierry_roman@fr.ibm.com
- * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com
- * Robert Snyder, AMCC/IBM, rob.snyder@fr.ibm.com
- *
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/* define DEBUG for debug output */
-#undef DEBUG
-
-#include <common.h>
-#include <asm/processor.h>
-#include <asm/io.h>
-#include <asm/mmu.h>
-#include <asm/cache.h>
-#include <asm/ppc440.h>
-
-void hcu_led_set(u32 value);
-void dcbz_area(u32 start_address, u32 num_bytes);
-
-#define ECC_RAM 0x03267F0B
-#define NO_ECC_RAM 0x00267F0B
-
-#define HCU_HW_SDRAM_CONFIG_MASK 0x7
-
-#define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE
- /* disable caching on DDR2 */
-
-void board_add_ram_info(int use_default)
-{
- PPC4xx_SYS_INFO board_cfg;
- u32 val;
-
- mfsdram(DDR0_22, val);
- val &= DDR0_22_CTRL_RAW_MASK;
- switch (val) {
- case DDR0_22_CTRL_RAW_ECC_DISABLE:
- puts(" (ECC disabled");
- break;
- case DDR0_22_CTRL_RAW_ECC_CHECK_ONLY:
- puts(" (ECC check only");
- break;
- case DDR0_22_CTRL_RAW_NO_ECC_RAM:
- puts(" (no ECC ram");
- break;
- case DDR0_22_CTRL_RAW_ECC_ENABLE:
- puts(" (ECC enabled");
- break;
- }
-
- get_sys_info(&board_cfg);
- printf(", %lu MHz", (board_cfg.freqPLB * 2) / 1000000);
-
- mfsdram(DDR0_03, val);
- val = DDR0_03_CASLAT_DECODE(val);
- printf(", CL%d)", val);
-}
-
-/*--------------------------------------------------------------------
- * wait_for_dlllock.
- *--------------------------------------------------------------------*/
-static int wait_for_dlllock(void)
-{
- unsigned long val;
- int wait = 0;
-
- /* -----------------------------------------------------------+
- * Wait for the DCC master delay line to finish calibration
- * ----------------------------------------------------------*/
- mtdcr(SDRAM0_CFGADDR, DDR0_17);
- val = DDR0_17_DLLLOCKREG_UNLOCKED;
-
- while (wait != 0xffff) {
- val = mfdcr(SDRAM0_CFGDATA);
- if ((val & DDR0_17_DLLLOCKREG_MASK) ==
- DDR0_17_DLLLOCKREG_LOCKED)
- /* dlllockreg bit on */
- return 0;
- else
- wait++;
- }
- debug("0x%04x: DDR0_17 Value (dlllockreg bit): 0x%08x\n", wait, val);
- debug("Waiting for dlllockreg bit to raise\n");
-
- return -1;
-}
-
-/***********************************************************************
- *
- * sdram_panic -- Panic if we cannot configure the sdram correctly
- *
- ************************************************************************/
-void sdram_panic(const char *reason)
-{
- printf("\n%s: reason %s", __FUNCTION__, reason);
- hcu_led_set(0xff);
- while (1) {
- }
- /* Never return */
-}
-
-#ifdef CONFIG_DDR_ECC
-void blank_string(int size)
-{
- int i;
-
- for (i=0; i<size; i++)
- putc('\b');
- for (i=0; i<size; i++)
- putc(' ');
- for (i=0; i<size; i++)
- putc('\b');
-}
-/*---------------------------------------------------------------------------+
- * program_ecc.
- *---------------------------------------------------------------------------*/
-static void program_ecc(unsigned long start_address, unsigned long num_bytes)
-{
- u32 val;
- char str[] = "ECC generation -";
-#if defined(CONFIG_PRAM)
- u32 *magicPtr;
- u32 magic;
-
- if ((mfspr(SPRN_DBCR0) & 0x80000000) == 0) {
- /* only if no external debugger is alive!
- * Check whether vxWorks is using EDR logging, if yes zero
- * also PostMortem and user reserved memory
- */
- magicPtr = (u32 *)(start_address + num_bytes -
- (CONFIG_PRAM*1024) + sizeof(u32));
- magic = in_be32(magicPtr);
- debug("%s: CONFIG_PRAM %d kB magic 0x%x 0x%p\n",
- __FUNCTION__, CONFIG_PRAM,
- magicPtr, magic);
- if (magic == 0xbeefbabe) {
- printf("%s: preserving at %p\n", __FUNCTION__, magicPtr);
- num_bytes -= (CONFIG_PRAM*1024) - PM_RESERVED_MEM;
- }
- }
-#endif
-
- sync();
-
- puts(str);
-
- /* ECC bit set method for cached memory */
- /* Fast method, no noticeable delay */
- dcbz_area(start_address, num_bytes);
- /* Write modified dcache lines back to memory */
- clean_dcache_range(start_address, start_address + num_bytes);
- blank_string(strlen(str));
-
- /* Clear error status */
- mfsdram(DDR0_00, val);
- mtsdram(DDR0_00, val | DDR0_00_INT_ACK_ALL);
-
- /*
- * Clear possible ECC errors
- * If not done, then we could get an interrupt later on when
- * exceptions are enabled.
- */
- mtspr(SPRN_MCSR, mfspr(SPRN_MCSR));
-
- /* Set 'int_mask' parameter to functionnal value */
- mfsdram(DDR0_01, val);
- mtsdram(DDR0_01, ((val &~ DDR0_01_INT_MASK_MASK) |
- DDR0_01_INT_MASK_ALL_OFF));
-
- return;
-}
-#endif
-
-
-/***********************************************************************
- *
- * initdram -- 440EPx's DDR controller is a DENALI Core
- *
- ************************************************************************/
-phys_size_t initdram (int board_type)
-{
- unsigned int dram_size = 0;
-
- mtsdram(DDR0_02, 0x00000000);
-
- /* Values must be kept in sync with Excel-table <<A0001492.>> ! */
- mtsdram(DDR0_00, 0x0000190A);
- mtsdram(DDR0_01, 0x01000000);
- mtsdram(DDR0_03, 0x02030602);
- mtsdram(DDR0_04, 0x0A020200);
- mtsdram(DDR0_05, 0x02020307);
- switch (in_be16((u16 *)HCU_HW_VERSION_REGISTER) & HCU_HW_SDRAM_CONFIG_MASK) {
- case 1:
- dram_size = 256 * 1024 * 1024 ;
- mtsdram(DDR0_06, 0x0102C812); /* 256MB RAM */
- mtsdram(DDR0_11, 0x0014C800); /* 256MB RAM */
- mtsdram(DDR0_43, 0x030A0200); /* 256MB RAM */
- break;
- case 0:
- default:
- dram_size = 128 * 1024 * 1024 ;
- mtsdram(DDR0_06, 0x0102C80D); /* 128MB RAM */
- mtsdram(DDR0_11, 0x000FC800); /* 128MB RAM */
- mtsdram(DDR0_43, 0x030A0300); /* 128MB RAM */
- break;
- }
- mtsdram(DDR0_07, 0x00090100);
-
- /*
- * TCPD=200 cycles of clock input is required to lock the DLL.
- * CKE must be HIGH the entire time.mtsdram(DDR0_08, 0x02C80001);
- */
- mtsdram(DDR0_08, 0x02C80001);
- mtsdram(DDR0_09, 0x00011D5F);
- mtsdram(DDR0_10, 0x00000100);
- mtsdram(DDR0_12, 0x00000003);
- mtsdram(DDR0_14, 0x00000000);
- mtsdram(DDR0_17, 0x1D000000);
- mtsdram(DDR0_18, 0x1D1D1D1D);
- mtsdram(DDR0_19, 0x1D1D1D1D);
- mtsdram(DDR0_20, 0x0B0B0B0B);
- mtsdram(DDR0_21, 0x0B0B0B0B);
-#ifdef CONFIG_DDR_ECC
- mtsdram(DDR0_22, ECC_RAM);
-#else
- mtsdram(DDR0_22, NO_ECC_RAM);
-#endif
-
- mtsdram(DDR0_23, 0x00000000);
- mtsdram(DDR0_24, 0x01020001);
- mtsdram(DDR0_26, 0x2D930517);
- mtsdram(DDR0_27, 0x00008236);
- mtsdram(DDR0_28, 0x00000000);
- mtsdram(DDR0_31, 0x00000000);
- mtsdram(DDR0_42, 0x01000006);
- mtsdram(DDR0_44, 0x00000003);
- mtsdram(DDR0_02, 0x00000001);
- wait_for_dlllock();
- mtsdram(DDR0_00, 0x40000000); /* Zero init bit */
-
- /*
- * Program tlb entries for this size (dynamic)
- */
- remove_tlb(CONFIG_SYS_SDRAM_BASE, 256 << 20);
- program_tlb(0, 0, dram_size, TLB_WORD2_W_ENABLE | TLB_WORD2_I_ENABLE);
-
- /*
- * Setup 2nd TLB with same physical address but different virtual
- * address with cache enabled. This is done for fast ECC generation.
- */
- program_tlb(0, CONFIG_SYS_DDR_CACHED_ADDR, dram_size, 0);
-
-#ifdef CONFIG_DDR_ECC
- /*
- * If ECC is enabled, initialize the parity bits.
- */
- program_ecc(CONFIG_SYS_DDR_CACHED_ADDR, dram_size);
-#endif
-
- return (dram_size);
-}
+++ /dev/null
-#
-# (C) Copyright 2007-2008 Netstal Maschinen AG
-# Niklaus Giger (ng@netstal.com)
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-ifneq ($(OBJTREE),$(SRCTREE))
-$(shell mkdir -p $(obj)../common)
-endif
-
-LIB = $(obj)lib$(BOARD).o
-
-COBJS = $(BOARD).o \
- ../common/fixed_sdram.o \
- ../common/nm_bsp.o
-
-SRCS := $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-
-$(LIB): $(OBJS)
- $(call cmd_link_o_target, $^)
-
-clean:
- rm -f $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
+++ /dev/null
-MCU25 Configuration Details
-
-Memory Bank 0 -- Flash chip
----------------------------
-
-0xfff00000 - 0xffffffff
-
-The flash chip is really only 512Kbytes, but the high address bit of
-the 1Meg region is ignored, so the flash is replicated through the
-region. Thus, this is consistent with a flash base address 0xfff80000.
-
-The placement at the end is to be consistent with reset behavior,
-where the processor itself initially uses this bus to load the branch
-vector and start running.
-
-On-Chip Memory
---------------
-
-0xf4000000 - 0xf4000fff
-
-The 405GPr includes a 4K on-chip memory that can be placed however
-software chooses. I choose to place the memory at this address, to
-keep it out of the cachable areas.
-
-
-Internal Peripherals
---------------------
-
-0xef600300 - 0xef6008ff
-
-These are scattered various peripherals internal to the PPC405GPr
-chip.
-
-Chip-Select 2: Flash Memory
----------------------------
-
-0x70000000
-
-Chip-Select 3: CAN Interface
-----------------------------
-0x7800000
-
-
-Chip-Select 4: IMC-bus standard
--------------------------------
-
-Our IO-Bus (slow version)
-
-
-Chip-Select 5: IMC-bus fast (inactive)
---------------------------------------
-
-Our IO-Bus (fast, but not yet use)
-
-
-Memory Bank 1 -- SDRAM
--------------------------------------
-
-0x00000000 - 0x2ffffff # Default 64 MB
+++ /dev/null
-#
-# (C) Copyright 2005 Netstal Maschinen AG
-# Niklaus Giger (ng@netstal.com)
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-#
-# Netstal Maschinen AG: MCU25 board
-#
-ifeq ($(debug),1)
-PLATFORM_CPPFLAGS += -DDEBUG -g
-endif
+++ /dev/null
-/*
- *(C) Copyright 2005-2008 Netstal Maschinen AG
- * Niklaus Giger (Niklaus.Giger@netstal.com)
- *
- * This source code is free software; you can redistribute it
- * and/or modify it in source code form under the terms of the GNU
- * General Public License as published by the Free Software
- * Foundation; either version 2 of the License, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA
- */
-
-#include <common.h>
-#include <asm/ppc4xx.h>
-#include <asm/processor.h>
-#include <asm/io.h>
-#include <asm/u-boot.h>
-#include "../common/nm.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define MCU25_SLOT_ADDRESS (0x7A000000 + 0x0A)
-#define MCU25_DIGITAL_IO_REGISTER (0x7A000000 + 0xc0)
-
-#define MCU25_LED_REGISTER_ADDRESS (0x7C000000 + 0x10)
-#define MCU25_VERSIONS_REGISTER (0x7C000000 + 0x0C)
-#define MCU25_IO_CONFIGURATION (0x7C000000 + 0x0e)
-#define MCU_SW_INSTALL_REQUESTED 0x08
-
-#define SDRAM_LEN (32 << 20) /* 32 MB - RAM */
-
-/*
- * This function is run very early, out of flash, and before devices are
- * initialized. It is called by arch/powerpc/lib/board.c:board_init_f by virtue
- * of being in the init_sequence array.
- *
- * The SDRAM has been initialized already -- start.S:start called
- * init.S:init_sdram early on -- but it is not yet being used for
- * anything, not even stack. So be careful.
- */
-
-/* Attention: If you want 1 microsecs times from the external oscillator
- * 0x00004051 is okay for u-boot/linux, but different from old vxworks values
- * 0x00804051 causes problems with u-boot and linux!
- */
-#define CPC0_CR0_VALUE 0x0007F03C
-#define CPC0_CR1_VALUE 0x00004051
-
-int board_early_init_f (void)
-{
- /* Documented in A-1171
- *
- * Interrupt controller setup for the MCU25 board.
- * Note: IRQ 0-15 405GP internally generated; high; level sensitive
- * IRQ 16 405GP internally generated; low; level sensitive
- * IRQ 17-24 RESERVED/UNUSED
- * IRQ 31 (EXT IRQ 6) (unused)
- */
- mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
- mtdcr(UIC0ER, 0x00000000); /* disable all ints */
- mtdcr(UIC0CR, 0x00000000); /* set all to be non-critical */
- mtdcr(UIC0PR, 0xFFFFE000); /* set int polarities */
- mtdcr(UIC0TR, 0x00000000); /* set int trigger levels */
- mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
-
- mtdcr(CPC0_CR1, CPC0_CR1_VALUE);
- mtdcr(CPC0_ECR, 0x60606000);
- mtdcr(CPC0_EIRR, 0x7C000000);
- out32(GPIO0_OR, CONFIG_SYS_GPIO0_OR );
- out32(GPIO0_TCR, CONFIG_SYS_GPIO0_TCR);
- out32(GPIO0_ODR, CONFIG_SYS_GPIO0_ODR);
- mtspr(SPRN_CCR0, 0x00700000);
-
- return 0;
-}
-
-#ifdef CONFIG_BOARD_PRE_INIT
-int board_pre_init (void)
-{
- return board_early_init_f ();
-}
-#endif
-
-int sys_install_requested(void)
-{
- u16 ioValue = in_be16((u16 *)MCU25_DIGITAL_IO_REGISTER);
- return (ioValue & MCU_SW_INSTALL_REQUESTED) != 0;
-}
-
-int checkboard (void)
-{
- u16 boardVersReg = in_be16((u16 *)MCU25_VERSIONS_REGISTER);
- u16 hwConfig = in_be16((u16 *)MCU25_IO_CONFIGURATION);
- u16 generation = boardVersReg & 0x0f;
- u16 index = boardVersReg & 0xf0;
-
- /* Cannot be done in board_early_init */
- mtdcr(CPC0_CR0, CPC0_CR0_VALUE);
-
- /* Force /RTS to active. The board it not wired quite
- * correctly to use cts/rtc flow control, so just force the
- * /RST active and forget about it.
- */
- writeb (readb (0xef600404) | 0x03, 0xef600404);
- nm_show_print(generation, index, hwConfig);
- return 0;
-}
-
-u32 hcu_led_get(void)
-{
- return in_be16((u16 *)MCU25_LED_REGISTER_ADDRESS) & 0x3ff;
-}
-
-/*
- * hcu_led_set value to be placed into the LEDs (max 6 bit)
- */
-void hcu_led_set(u32 value)
-{
- out_be16((u16 *)MCU25_LED_REGISTER_ADDRESS, value);
-}
-
-/*
- * hcu_get_slot
- */
-u32 hcu_get_slot(void)
-{
- u16 slot = in_be16((u16 *)MCU25_SLOT_ADDRESS);
- return slot & 0x7f;
-}
-
-/*
- * get_serial_number
- */
-u32 get_serial_number(void)
-{
- u32 serial = in_be32((u32 *)CONFIG_SYS_FLASH_BASE);
-
- if (serial == 0xffffffff)
- return 0;
-
- return serial;
-}
-
-
-/*
- * misc_init_r.
- */
-
-int misc_init_r(void)
-{
- common_misc_init_r();
- set_params_for_sw_install( sys_install_requested(), "mcu25" );
- return 0;
-}
-
-phys_size_t initdram(int board_type)
-{
- unsigned int dram_size = 64*1024*1024;
- init_ppc405_sdram(dram_size);
-
-#ifdef DEBUG
- show_sdram_registers();
-#endif
-
- return dram_size;
-}
-
-#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
-void ft_board_setup(void *blob, bd_t *bd)
-{
- ft_cpu_setup(blob, bd);
-
-}
-#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
-
-/*
- * Hardcoded flash setup:
- * Flash 0 is a non-CFI AMD AM29F040 flash, 8 bit flash / 8 bit bus.
- */
-ulong board_flash_get_legacy (ulong base, int banknum, flash_info_t * info)
-{
- if (banknum == 0) { /* non-CFI boot flash */
- info->portwidth = 1;
- info->chipwidth = 1;
- info->interface = FLASH_CFI_X8;
- return 1;
- } else
- return 0;
-}
MIP405 powerpc ppc4xx mip405 mpl
MIP405T powerpc ppc4xx mip405 mpl - MIP405:MIP405T
PIP405 powerpc ppc4xx pip405 mpl
-hcu4 powerpc ppc4xx hcu4 netstal
-hcu5 powerpc ppc4xx hcu5 netstal
-mcu25 powerpc ppc4xx mcu25 netstal
alpr powerpc ppc4xx - prodrive
p3p440 powerpc ppc4xx - prodrive
KAREF powerpc ppc4xx karef sandburst
+++ /dev/null
-/*
- *(C) Copyright 2005-2008 Netstal Maschinen AG
- * Niklaus Giger (Niklaus.Giger@netstal.com)
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/************************************************************************
- * hcu4.h - configuration for HCU4 board (similar to hcu5.h)
- ***********************************************************************/
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*-----------------------------------------------------------------------
- * High Level Configuration Options
- *----------------------------------------------------------------------*/
-#define CONFIG_HCU4 1 /* Board is HCU4 */
-#define CONFIG_4xx 1 /* ... PPC4xx family */
-#define CONFIG_405GP 1
-#define CONFIG_4xx 1
-#define CONFIG_HOSTNAME hcu4
-
-#define CONFIG_SYS_TEXT_BASE 0xFFFB0000
-
-/*
- * Include common defines/options for all boards produced by Netstal Maschinen
- */
-#include "netstal-common.h"
-
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
-
-/*-----------------------------------------------------------------------
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
-*----------------------------------------------------------------------*/
-#define CONFIG_SYS_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-
-
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CONFIG_SYS_FLASH_BASE 0xfff80000 /* start of FLASH */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-/* ... with on-chip memory here (4KBytes) */
-#define CONFIG_SYS_OCM_DATA_ADDR 0xF4000000
-#define CONFIG_SYS_OCM_DATA_SIZE 0x00001000
-/* Do not set up locked dcache as init ram. */
-#undef CONFIG_SYS_INIT_DCACHE_CS
-
-/* Use the On-Chip-Memory (OCM) as a temporary stack for the startup code. */
-#define CONFIG_SYS_TEMP_STACK_OCM 1
-
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* OCM */
-#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
-
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-/*
- * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
- * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
- * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
- * The Linux BASE_BAUD define should match this configuration.
- * baseBaud = cpuClock/(uartDivisor*16)
- * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
- * set Linux BASE_BAUD to 403200.
- */
-#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
-#define CONFIG_SYS_BASE_BAUD 691200
-
-/* Set console baudrate to 9600 */
-#define CONFIG_BAUDRATE 9600
-
-/*-----------------------------------------------------------------------
- * Flash
- *----------------------------------------------------------------------*/
-
-/* Use common CFI driver */
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-/* board provides its own flash_init code */
-#define CONFIG_FLASH_CFI_LEGACY 1
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
-#define CONFIG_SYS_FLASH_LEGACY_512Kx8 1
-
-/* print 'E' for empty sector on flinfo */
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
-
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-
-#undef CONFIG_ENV_IS_IN_NVRAM
-#define CONFIG_ENV_IS_IN_FLASH
-#undef CONFIG_ENV_IS_NOWHERE
-
-#ifdef CONFIG_ENV_IS_IN_EEPROM
-/* Put the environment after the SDRAM configuration */
-#define PROM_SIZE 2048
-#define CONFIG_ENV_OFFSET 512
-#define CONFIG_ENV_SIZE (PROM_SIZE-CONFIG_ENV_OFFSET)
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-/* Put the environment in Flash */
-#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
-#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE 8*1024 /* 8 KB Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-#endif
-
-/*-----------------------------------------------------------------------
- * I2C stuff for a ATMEL AT24C16 (2kB holding ENV, we are using the
- * the first internal I2C controller of the PPC440EPx
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_SPD_BUS_NUM 0
-
-#define CONFIG_IPADDR 172.25.1.14
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_NETSTAL_DEF_ENV \
- CONFIG_NETSTAL_DEF_ENV_POWERPC \
- ""
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SDRAM
-
-/* SPD EEPROM (sdram speed config) disabled */
-#define CONFIG_SPD_EEPROM 1
-#define SPD_EEPROM_ADDRESS 0x50
-
-/* POST support */
-#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
- CONFIG_SYS_POST_CPU | \
- CONFIG_SYS_POST_UART | \
- CONFIG_SYS_POST_I2C | \
- CONFIG_SYS_POST_CACHE | \
- CONFIG_SYS_POST_ETHER | \
- CONFIG_SYS_POST_SPR)
-
-#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 }
-#undef CONFIG_LOGBUFFER
-#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
- #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- */
-
-#define CONFIG_SYS_EBC_CFG 0x98400000
-
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CONFIG_SYS_EBC_PB0AP 0x02005400
-#define CONFIG_SYS_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */
-
-#define CONFIG_SYS_EBC_PB1AP 0x03041200
-#define CONFIG_SYS_EBC_PB1CR 0x7009A000 /* BAS=,BS=MB,BU=R/W,BW=bit */
-
-#define CONFIG_SYS_EBC_PB2AP 0x02054500
-#define CONFIG_SYS_EBC_PB2CR 0x78018000 /* BAS=,BS=MB,BU=R/W,BW=bit */
-
-#define CONFIG_SYS_EBC_PB3AP 0x01840300
-#define CONFIG_SYS_EBC_PB3CR 0x7c0ba000 /* BAS=,BS=MB,BU=R/W,BW=bit */
-
-#define CONFIG_SYS_EBC_PB4AP 0x01800300
-#define CONFIG_SYS_EBC_PB4CR 0x7e0ba000 /* BAS=,BS=MB,BU=R/W,BW=bit */
-
-#define CONFIG_SYS_GPIO0_OR 0xF27FFFFF /* GPIO value */
-#define CONFIG_SYS_GPIO0_TCR 0x7FFE0000 /* GPIO value */
-#define CONFIG_SYS_GPIO0_ODR 0x00E897FC /* GPIO value */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20)/* Initial Memory map for Linux */
-
-/* Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
-
-
-/* Configuration Port location */
-#define CONFIG_PORT_ADDR 0xF0000500
-
-#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * (C) Copyright 2007-2008 Netstal Maschinen AG
- * Niklaus Giger (Niklaus.Giger@netstal.com)
- *
- * (C) Copyright 2006-2007
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * (C) Copyright 2006
- * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
- * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/************************************************************************
- * hcu5.h - configuration for HCU5 board (derived from sequoia.h)
- ***********************************************************************/
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*-----------------------------------------------------------------------
- * High Level Configuration Options
- *----------------------------------------------------------------------*/
-#define CONFIG_HCU5 1 /* Board is HCU5 */
-#define CONFIG_440EPX 1 /* Specific PPC440EPx */
-#define CONFIG_440 1 /* ... PPC440 family */
-#define CONFIG_4xx 1 /* ... PPC4xx family */
-#define CONFIG_HOSTNAME hcu5
-
-#define CONFIG_SYS_TEXT_BASE 0xFFFB0000
-
-/*
- * Include common defines/options for all boards produced by Netstal Maschinen
- */
-#include "netstal-common.h"
-
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
-
-/*-----------------------------------------------------------------------
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-
-#define CONFIG_SYS_TLB_FOR_BOOT_FLASH 3
-#define CONFIG_SYS_BOOT_BASE_ADDR 0xfff00000
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CONFIG_SYS_FLASH_BASE 0xfff80000 /* start of FLASH */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */
-#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_OCM_BASE
-#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */
-#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
-#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
-#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
-#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
-
-#define CONFIG_SYS_USB2D0_BASE 0xe0000100
-#define CONFIG_SYS_USB_DEVICE 0xe0000000
-#define CONFIG_SYS_USB_HOST 0xe0000400
-
-/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer
- *----------------------------------------------------------------------*/
-/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */
-
-#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10)
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
-
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
-#define CONFIG_BAUDRATE 115200
-
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-
-#undef CONFIG_ENV_IS_IN_NVRAM
-#define CONFIG_ENV_IS_IN_FLASH
-#undef CONFIG_ENV_IS_IN_EEPROM
-#undef CONFIG_ENV_IS_NOWHERE
-
-#ifdef CONFIG_ENV_IS_IN_EEPROM
-/* Put the environment after the SDRAM and bootstrap configuration */
-#define PROM_SIZE 2048
-#define CONFIG_SYS_BOOSTRAP_OPTION_OFFSET 512
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_BOOSTRAP_OPTION_OFFSET + 0x10)
-#define CONFIG_ENV_SIZE (PROM_SIZE-CONFIG_ENV_OFFSET)
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-/* Put the environment in Flash */
-#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
-#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE 8*1024 /* 8 KB Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#endif
-
-/*-----------------------------------------------------------------------
- * DDR SDRAM
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MBYTES_SDRAM (128) /* 128 MB or 256 MB */
-#define CONFIG_SYS_DDR_CACHED_ADDR 0x50000000 /* setup 2nd TLB cached here */
-#undef CONFIG_DDR_DATA_EYE /* Do not use DDR2 optimization */
-#define CONFIG_DDR_ECC 1 /* enable ECC */
-
-/* Following two definitions must be kept in sync with config.h of vxWorks */
-#define USER_RESERVED_MEM ( 0) /* in kB */
-#define PM_RESERVED_MEM ( 64) /* in kB: pmLib reserved area size */
-#define CONFIG_PRAM ( USER_RESERVED_MEM + PM_RESERVED_MEM )
-
-#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
- /* 440EPx errata CHIP 11 */
-
-/*-----------------------------------------------------------------------
- * I2C stuff for a ATMEL AT24C16 (2kB holding ENV, we are using the
- * the second internal I2C controller of the PPC440EPx
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_SPD_BUS_NUM 1
-
-/* Setup some board specific values for the default environment variables */
-#define CONFIG_IPADDR 172.25.1.15
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_NETSTAL_DEF_ENV \
- CONFIG_NETSTAL_DEF_ENV_POWERPC \
- ""
-
-#define CONFIG_M88E1111_PHY 1
-#define CONFIG_IBM_EMAC4_V4 1
-
-#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
-#define CONFIG_PHY1_ADDR 2
-
-/* USB */
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_STORAGE
-
-/* Comment this out to enable USB 1.1 device */
-#define USB_2_0_DEVICE
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_USB
-
-/* POST support */
-#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
- CONFIG_SYS_POST_UART | \
- CONFIG_SYS_POST_I2C | \
- CONFIG_SYS_POST_CACHE | \
- CONFIG_SYS_POST_FPU | \
- CONFIG_SYS_POST_ETHER | \
- CONFIG_SYS_POST_SPR)
-
-#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 }
-#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
-
-#define CONFIG_SUPPORT_VFAT
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *----------------------------------------------------------------------*/
-/* General PCI */
-#define CONFIG_PCI 1 /* include pci support */
-#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */
-#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr map to CONFIG_SYS_PCI_MEMBASE*/
-
-/* Board-specific PCI */
-#define CONFIG_SYS_PCI_TARGET_INIT
-#define CONFIG_SYS_PCI_MASTER_INIT
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
-#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * Flash
- *----------------------------------------------------------------------*/
-
-/* Use common CFI driver */
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-/* board provides its own flash_init code */
-#define CONFIG_FLASH_CFI_LEGACY 1
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
-#define CONFIG_SYS_FLASH_LEGACY_512Kx8 1
-
-/* print 'E' for empty sector on flinfo */
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS_1 0xC8000000 /* CAN */
-#define CONFIG_SYS_CS_2 0xCC000000 /* CPLD and IMC-Bus Standard */
-#define CONFIG_SYS_CPLD CONFIG_SYS_CS_2
-#define CONFIG_SYS_CS_3 0xCE000000 /* CPLD and IMC-Bus Fast */
-
-#define CONFIG_SYS_BOOTFLASH_CS 0 /* Boot Flash chip connected to CSx */
-#define CONFIG_SYS_EBC_PB0AP 0x02005400
-#define CONFIG_SYS_EBC_PB0CR 0xFFF18000 /* (CONFIG_SYS_FLASH | 0xda000) */
-#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
-
-/* Memory Bank 1 CAN-Chips initialization */
-#define CONFIG_SYS_EBC_PB1AP 0x02054500
-#define CONFIG_SYS_EBC_PB1CR 0xC8018000
-
-/* Memory Bank 2 CPLD/IMC-Bus standard initialization */
-#define CONFIG_SYS_EBC_PB2AP 0x01840300
-#define CONFIG_SYS_EBC_PB2CR 0xCC0BA000
-
-/* Memory Bank 3 IMC-Bus fast mode initialization */
-#define CONFIG_SYS_EBC_PB3AP 0x01800300
-#define CONFIG_SYS_EBC_PB3CR 0xCE0BA000
-
-/* Memory Bank 4 (not used) initialization */
-#undef CONFIG_SYS_EBC_PB4AP
-#undef CONFIG_SYS_EBC_PB4CR
-
-/* Memory Bank 5 (not used) initialization */
-#undef CONFIG_SYS_EBC_PB5AP
-#undef CONFIG_SYS_EBC_PB5CR
-
-#define HCU_CPLD_VERSION_REGISTER ( CONFIG_SYS_CPLD + 0x0F00000 )
-#define HCU_HW_VERSION_REGISTER ( CONFIG_SYS_CPLD + 0x1400000 )
-
-#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#ifdef CONFIG_SYS_HUSH_PARSER
- #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- *(C) Copyright 2005-2007 Netstal Maschinen AG
- * Niklaus Giger (Niklaus.Giger@netstal.com)
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/************************************************************************
- * mcu25.h - configuration for MCU25 board (similar to hcu4.h)
- ***********************************************************************/
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*-----------------------------------------------------------------------
- * High Level Configuration Options
- *----------------------------------------------------------------------*/
-#define CONFIG_MCU25 1 /* Board is MCU25 */
-#define CONFIG_4xx 1 /* ... PPC4xx family */
-#define CONFIG_405GP 1
-#define CONFIG_4xx 1
-#define CONFIG_HOSTNAME mcu25
-
-#define CONFIG_SYS_TEXT_BASE 0xFFFB0000
-
-/*
- * Include common defines/options for all boards produced by Netstal Maschinen
- */
-#include "netstal-common.h"
-
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
-
-/*-----------------------------------------------------------------------
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
-*----------------------------------------------------------------------*/
-#define CONFIG_SYS_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-
-
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CONFIG_SYS_FLASH_BASE 0xfff80000 /* start of FLASH */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-/* ... with on-chip memory here (4KBytes) */
-#define CONFIG_SYS_OCM_DATA_ADDR 0xF4000000
-#define CONFIG_SYS_OCM_DATA_SIZE 0x00001000
-/* Do not set up locked dcache as init ram. */
-#undef CONFIG_SYS_INIT_DCACHE_CS
-
-/* Use the On-Chip-Memory (OCM) as a temporary stack for the startup code. */
-#define CONFIG_SYS_TEMP_STACK_OCM 1
-
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* OCM */
-#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
-
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-/*
- * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
- * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
- * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
- * The Linux BASE_BAUD define should match this configuration.
- * baseBaud = cpuClock/(uartDivisor*16)
- * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
- * set Linux BASE_BAUD to 403200.
- */
-#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
-#define CONFIG_SYS_BASE_BAUD 691200
-
-/* Set console baudrate to 9600 */
-#define CONFIG_BAUDRATE 9600
-
-/*-----------------------------------------------------------------------
- * Flash
- *----------------------------------------------------------------------*/
-
-/* Use common CFI driver */
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-/* board provides its own flash_init code */
-#define CONFIG_FLASH_CFI_LEGACY 1
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
-#define CONFIG_SYS_FLASH_LEGACY_512Kx8 1
-
-/* print 'E' for empty sector on flinfo */
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
-
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-
-#undef CONFIG_ENV_IS_IN_NVRAM
-#define CONFIG_ENV_IS_IN_FLASH
-#undef CONFIG_ENV_IS_NOWHERE
-
-#ifdef CONFIG_ENV_IS_IN_EEPROM
-/* Put the environment after the SDRAM configuration */
-#define PROM_SIZE 2048
-#define CONFIG_ENV_OFFSET 512
-#define CONFIG_ENV_SIZE (PROM_SIZE-CONFIG_ENV_OFFSET)
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-/* Put the environment in Flash */
-#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
-#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE 8*1024 /* 8 KB Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-#endif
-
-/*-----------------------------------------------------------------------
- * I2C stuff for a ATMEL AT24C16 (2kB holding ENV, we are using the
- * the first internal I2C controller of the PPC440EPx
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_SPD_BUS_NUM 0
-
-/* Setup some board specific values for the default environment variables */
-#define CONFIG_IPADDR 172.25.1.25
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_NETSTAL_DEF_ENV \
- CONFIG_NETSTAL_DEF_ENV_POWERPC \
- ""
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SDRAM
-
-/* SPD EEPROM (sdram speed config) disabled */
-#define CONFIG_SPD_EEPROM 1
-#define SPD_EEPROM_ADDRESS 0x50
-
-/* POST support */
-#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
- CONFIG_SYS_POST_CPU | \
- CONFIG_SYS_POST_UART | \
- CONFIG_SYS_POST_I2C | \
- CONFIG_SYS_POST_CACHE | \
- CONFIG_SYS_POST_ETHER | \
- CONFIG_SYS_POST_SPR)
-
-#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 }
-#undef CONFIG_LOGBUFFER
-#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
- #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- */
-
-#define CONFIG_SYS_EBC_CFG 0x98400000
-
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CONFIG_SYS_EBC_PB0AP 0x02005400
-#define CONFIG_SYS_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit*/
-
-#define CONFIG_SYS_EBC_PB1AP 0x03041200
-#define CONFIG_SYS_EBC_PB1CR 0x7009A000 /* BAS=,BS=MB,BU=R/W,BW=bit */
-
-#define CONFIG_SYS_EBC_PB2AP 0x01845200u /* BAS=,BS=MB,BU=R/W,BW=bit */
-#define CONFIG_SYS_EBC_PB2CR 0x7A09A000u
-
-#define CONFIG_SYS_EBC_PB3AP 0x01845200u /* BAS=,BS=MB,BU=R/W,BW=bit */
-#define CONFIG_SYS_EBC_PB3CR 0x7B09A000u
-
-#define CONFIG_SYS_EBC_PB4AP 0x01845200u /* BAS=,BS=MB,BU=R/W,BW=bit */
-#define CONFIG_SYS_EBC_PB4CR 0x7C09A000u
-
-#define CONFIG_SYS_EBC_PB5AP 0x00800200u
-#define CONFIG_SYS_EBC_PB5CR 0x7D81A000u
-
-#define CONFIG_SYS_EBC_PB6AP 0x01040200u
-#define CONFIG_SYS_EBC_PB6CR 0x7D91A000u
-
-#define CONFIG_SYS_GPIO0_OR 0x087FFFFF /* GPIO value */
-#define CONFIG_SYS_GPIO0_TCR 0x7FFF8000 /* GPIO value */
-#define CONFIG_SYS_GPIO0_ODR 0xFFFF0000 /* GPIO value */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/* Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
-
-
-/* Configuration Port location */
-#define CONFIG_PORT_ADDR 0xF0000500
-
-#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * (C) Copyright 2008
- * Niklaus Giger, Netstal Maschinen AG, niklaus.giger@netstal.com
- * adapted from amcc-common.h by
- * (C) Copyright 2008
- * * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * Common configuration options for all Netstal boards
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __NETSTAL_COMMON_H
-#define __NETSTAL_COMMON_H
-
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* Start of U-Boot */
-#define CONFIG_SYS_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-
-/*
- * UART
- */
-#define CONFIG_CONS_INDEX 1 /* Use UART0 */
-#define CONFIG_SERIAL_MULTI
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_serial_clock()
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-/*
- * I2C
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/* This is the 7bit address of the device, not including P. */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/* The EEPROM can do 16byte ( 1 << 4 ) page writes. */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE
-
-/*
- * Ethernet/EMAC/PHY
- */
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII /* MII PHY management */
-#define CONFIG_PHY_ADDR 1 /* PHY address */
-#define CONFIG_NET_MULTI 1
-#if defined(CONFIG_440)
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_SYS_RX_ETH_BUFFER 32 /* number of eth rx buffers */
-#else
-#define CONFIG_SYS_RX_ETH_BUFFER 16 /* number of eth rx buffers */
-#endif
-#define CONFIG_HAS_ETH0
-
-/*
- * Commands
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#if defined(CONFIG_440)
-#define CONFIG_CMD_CACHE
-#endif
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_BOOT_RETRY_TIME 30
-#define CONFIG_RESET_TO_RETRY
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO /* To use extended board_into (bd_t) */
-
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING /* add command line history */
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
-#define CONFIG_LOOPW /* enable loopw command */
-#define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE /* include version env variable */
-#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup*/
-
-#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
-
-#define CONFIG_LOADS_ECHO /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-
-/*
- * Booting and default environment
- */
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run net_nfs\" to mount root filesystem over NFS;" \
- "echo"
-#define CONFIG_BOOTCOMMAND "run vx"
-
-/*
- * Only very few boards have default console not on ttyS0 (like Taishan)
- */
-#if !defined(CONFIG_USE_TTY)
-#define CONFIG_USE_TTY ttyS0
-#endif
-
-/*
- * Only some 4xx PPC's are equipped with an FPU
- */
-#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \
- defined(CONFIG_460EX) || defined(CONFIG_460GT)
-#define CONFIG_NETSTAL_DEF_ENV_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0"
-#else
-#define CONFIG_NETSTAL_DEF_ENV_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0"
-#endif
-
-/*
- * Only some boards need to extend the bootargs by some additional
- * parameters (like Makalu)
- */
-#if !defined(CONFIG_ADDMISC)
-#define CONFIG_ADDMISC "addmisc=setenv bootargs ${bootargs}\0"
-#endif
-
-#define xstr(s) str(s)
-#define str(s) #s
-
-/* Setup some values for the default environment variables */
-#define CONFIG_SERVERIP 172.25.1.1
-#define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG MAC */
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-
-#define CONFIG_SYS_TFTP_LOADADDR 0x01000000
-#define CONFIG_SYS_VXWORKS_ADD_PARAMS "u=dpu pw=netstal8752"
-#define CONFIG_SYS_VXWORKS_SERVERNAME "c"
-/*
- * General common environment variables shared by all boards produced by Netstal Maschinen
- */
-#define CONFIG_NETSTAL_DEF_ENV \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs}" \
- " console=" xstr(CONFIG_USE_TTY) ",${baudrate}\0" \
- CONFIG_ADDMISC \
- "initrd_high=30000000\0" \
- "kernel_addr_r=400000\0" \
- "fdt_addr_r=800000\0" \
- "hostname=" xstr(CONFIG_HOSTNAME) "\0" \
- "bootfile=" xstr(CONFIG_HOSTNAME) "/uImage\0" \
- "uload=tftp " xstr(CONFIG_SYS_TFTP_LOADADDR) " " \
- xstr(CONFIG_HOSTNAME) "/u-boot.bin\0" \
- "vx_rom=" xstr(CONFIG_HOSTNAME) "/" \
- xstr(CONFIG_HOSTNAME) "_vx_rom\0" \
- "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) " FFFFFFFF;"\
- "era " xstr(CONFIG_SYS_MONITOR_BASE) " FFFFFFFF;" \
- "cp.b ${fileaddr} "xstr(CONFIG_SYS_MONITOR_BASE) \
- " ${filesize}; setenv filesize\0" \
- "upd=run uload update\0" \
- "vx=setenv bootfile ${vx_rom}; tftp " \
- xstr(CONFIG_SYS_TFTP_LOADADDR) "; bootvx\0" \
- CONFIG_NETSTAL_DEF_ENV_ROOTPATH
-
-/*
- * Default environment for arch/powerpc booting
- * for boards that are ported to arch/powerpc
- */
-#define CONFIG_NETSTAL_DEF_ENV_POWERPC \
- "flash_self=run ramargs addip addtty addmisc;" \
- "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
- "flash_nfs=run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "tftp ${fdt_addr_r} ${fdt_file}; " \
- "run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
- "fdt_file=" xstr(CONFIG_HOSTNAME) "/" xstr(CONFIG_HOSTNAME) ".dtb\0"
-
-#endif /* __NETSTAL_COMMON_H */
projects / u-boot / commitdiff