--- /dev/null
+/*
+ * (C) Copyright 2007 Netstal Maschinen AG
+ * Niklaus Giger (Niklaus.Giger@netstal.com)
+ *
+ * (C) Copyright 2006-2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * (C) Copyright 2006
+ * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
+ * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * hcu5.h - configuration for HCU5 board (derived from sequoia.h)
+ ***********************************************************************/
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_HCU5 1 /* Board is HCU5 */
+#define CONFIG_440EPX 1 /* Specific PPC440EPx */
+#define CONFIG_440 1 /* ... PPC440 family */
+#define CONFIG_4xx 1 /* ... PPC4xx family */
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
+#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
+#define CONFIG_ADD_RAM_INFO 1 /* Print additional info */
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
+#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
+
+#define CFG_BOOT_BASE_ADDR 0xfff00000
+#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
+#define CFG_FLASH_BASE 0xfff80000 /* start of FLASH */
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_OCM_BASE 0xe0010000 /* ocm */
+#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */
+#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
+#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
+#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
+#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
+
+/* Don't change either of these */
+#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
+
+#define CFG_USB2D0_BASE 0xe0000100
+#define CFG_USB_DEVICE 0xe0000000
+#define CFG_USB_HOST 0xe0000400
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer
+ *----------------------------------------------------------------------*/
+/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
+#define CFG_INIT_RAM_OCM 1 /* OCM as init ram */
+#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */
+
+#define CFG_INIT_RAM_END (4 << 10)
+#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
+#define CONFIG_BAUDRATE 9600
+#undef CONFIG_SERIAL_MULTI /* needed to be able to define
+ CONFIG_SERIAL_SOFTWARE_FIFO, but
+ CONFIG_SERIAL_SOFTWARE_FIFO (16) does not work */
+/* Size (bytes) of interrupt driven serial port buffer.
+ * Set to 0 to use polling instead of interrupts.
+ * Setting to 0 will also disable RTS/CTS handshaking.
+ */
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#undef CONFIG_UART1_CONSOLE
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+
+#undef CFG_ENV_IS_IN_NVRAM
+#undef CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_IS_IN_EEPROM
+#undef CFG_ENV_IS_NOWHERE
+
+#ifdef CFG_ENV_IS_IN_EEPROM
+/* Put the environment after the SDRAM and bootstrap configuration */
+#define PROM_SIZE 2048
+#define CFG_BOOSTRAP_OPTION_OFFSET 512
+#define CFG_ENV_OFFSET (CFG_BOOSTRAP_OPTION_OFFSET + 0x10)
+#define CFG_ENV_SIZE (PROM_SIZE-CFG_ENV_OFFSET)
+#endif
+
+#ifdef CFG_ENV_IS_IN_FLASH
+/* Put the environment in Flash */
+#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
+#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
+
+/* Address and size of Redundant Environment Sector */
+#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#endif
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#define CFG_MBYTES_SDRAM (128) /* 128 MB or 256 MB */
+#define CFG_DDR_CACHED_ADDR 0x40000000 /* setup 2nd TLB cached here */
+#undef CONFIG_DDR_DATA_EYE /* Do not use DDR2 optimization */
+#define CONFIG_DDR_ECC 1 /* enable ECC */
+
+/*-----------------------------------------------------------------------
+ * I2C stuff for a ATMEL AT24C16 (2kB holding ENV, we are using the
+ * the second internal I2C controller of the PPC440EPx
+ *----------------------------------------------------------------------*/
+#define CFG_SPD_BUS_NUM 1
+
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+/* This is the 7bit address of the device, not including P. */
+#define CFG_I2C_EEPROM_ADDR 0x50
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+
+/* The EEPROM can do 16byte ( 1 << 4 ) page writes. */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 4
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#undef CFG_I2C_MULTI_EEPROMS
+
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \"run nfs\" to mount Linux root filesystem over NFS;"\
+ "echo"
+
+#undef CONFIG_BOOTARGS
+
+/* Setup some board specific values for the default environment variables */
+#define CONFIG_HOSTNAME hcu5
+#define CONFIG_IPADDR 172.25.1.42
+#define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG MAC */
+#define CONFIG_OVERWRITE_ETHADDR_ONCE
+#define CONFIG_SERVERIP 172.25.1.3
+
+#define CFG_TFTP_LOADADDR 0x01000000 /* @16 MB */
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "loadaddr=0x01000000\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+ "nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
+ "bootm\0" \
+ "bootfile=hcu5/uImage\0" \
+ "rootpath=/home/hcu/eldk/ppc_4xxFP\0" \
+ "load=tftp 100000 hcu5/u-boot.bin\0" \
+ "update=protect off FFFa0000 FFFFFFFF;era FFFa0000 FFFFFFFF;" \
+ "cp.b 100000 FFFa0000 60000\0" \
+ "upd=run load;run update\0" \
+ "vx=tftp ${loadaddr} hcu5/hcu5_vx_rom;" \
+ "setenv bootargs emac(0,0)hcu5_vx_rom e=${ipaddr} " \
+ " h=${serverip} u=dpu pw=netstal8752 tn=hcu5 f=0x3008;" \
+ "bootvx ${loadaddr}\0" \
+ ""
+#define CONFIG_BOOTCOMMAND "run vx"
+
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_M88E1111_PHY 1
+#define CONFIG_IBM_EMAC4_V4 1
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
+
+#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
+
+#define CONFIG_HAS_ETH0
+#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NET_MULTI 1
+#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
+#define CONFIG_PHY1_ADDR 1
+
+/* USB */
+#define CONFIG_USB_OHCI
+#define CONFIG_USB_STORAGE
+
+/* Comment this out to enable USB 1.1 device */
+#define USB_2_0_DEVICE
+
+#define CMD_USB CFG_CMD_USB
+
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+
+// CFG_CMD_FLASH |
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_BSP | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_DIAG | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_ELF | \
+ CFG_CMD_FAT | \
+ CFG_CMD_I2C | \
+ CFG_CMD_IMMAP | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_MII | \
+ CFG_CMD_NET | \
+ CFG_CMD_NFS | \
+ CFG_CMD_PCI | \
+ CFG_CMD_PING | \
+ CFG_CMD_REGINFO | \
+ CFG_CMD_SDRAM | \
+ CMD_USB)
+
+#define CONFIG_SUPPORT_VFAT
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ *----------------------------------------------------------------------*/
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *----------------------------------------------------------------------*/
+/* General PCI */
+#define CONFIG_PCI /* include pci support */
+#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
+
+/* Board-specific PCI */
+#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */
+#define CFG_PCI_TARGET_INIT
+#define CFG_PCI_MASTER_INIT
+
+#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
+#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH CFG_FLASH_BASE
+#define CFG_CS_1 0xC8000000 /* CAN */
+#define CFG_CS_2 0xCC000000 /* CPLD and IMC-Bus Standard */
+#define CFG_CPLD CFG_CS_2
+#define CFG_CS_3 0xCD000000 /* CPLD and IMC-Bus Fast */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ * Memory Bank 0 (BOOT-FLASH) initialization
+ */
+#define CFG_BOOTFLASH_CS 0 /* Boot Flash chip connected to CSx */
+#define CFG_EBC_PB0AP 0x02005400
+#define CFG_EBC_PB0CR 0xFFF18000 /* (CFG_FLASH | 0xda000) */
+#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 32 /* max number of sectors on one chip */
+
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+/* Memory Bank 1 CAN-Chips initialization */
+#define CFG_EBC_PB1AP 0x02054500
+#define CFG_EBC_PB1CR 0xC8018000
+
+/* Memory Bank 2 CPLD/IMC-Bus standard initialization */
+#define CFG_EBC_PB2AP 0x01840300
+#define CFG_EBC_PB2CR 0xCC0BA000
+
+/* Memory Bank 3 IMC-Bus fast mode initialization */
+#define CFG_EBC_PB3AP 0x01800300
+#define CFG_EBC_PB3CR 0xCE0BA000
+
+/* Memory Bank 4 (not used) initialization */
+#undef CFG_EBC_PB4AP
+#undef CFG_EBC_PB4CR
+
+/* Memory Bank 5 (not used) initialization */
+#undef CFG_EBC_PB5AP
+#undef CFG_EBC_PB5CR
+
+#define HCU_CPLD_VERSION_REGISTER ( CFG_CPLD + 0x0F00000 )
+#define HCU_HW_VERSION_REGISTER ( CFG_CPLD + 0x1400000 )
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ *----------------------------------------------------------------------*/
+#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */
+#define CFG_CACHELINE_SIZE 32 /* ... */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#define CFG_HUSH_PARSER /* use "hush" command parser */
+#ifdef CFG_HUSH_PARSER
+ #define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+#endif /* __CONFIG_H */
+
projects / u-boot / commitdiff