select DM
select DM_THERMAL
+config TARGET_PICO_IMX7D
+ bool "pico-imx7d"
+ select BOARD_LATE_INIT
+ select MX7D
+ select DM
+ select DM_THERMAL
+
config TARGET_WARP7
bool "warp7"
select BOARD_LATE_INIT
default "mx7"
source "board/freescale/mx7dsabresd/Kconfig"
+source "board/technexion/pico-imx7d/Kconfig"
source "board/toradex/colibri_imx7/Kconfig"
source "board/warp7/Kconfig"
--- /dev/null
+if TARGET_PICO_IMX7D
+
+config SYS_BOARD
+ default "pico-imx7d"
+
+config SYS_VENDOR
+ default "technexion"
+
+config SYS_SOC
+ default "mx7"
+
+config SYS_CONFIG_NAME
+ default "pico-imx7d"
+
+endif
--- /dev/null
+Technexion PICO-IMX7D board
+M: Wig Cheng <wig.cheng@technexion.com>
+M: Vanessa Maegima <vanessa.maegima@nxp.com>
+S: Maintained
+F: board/technexion/pico-imx7d/
+F: include/configs/pico-imx7d.h
+F: configs/pico-imx7d_defconfig
--- /dev/null
+# (C) Copyright 2017 NXP Semiconductors
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := pico-imx7d.o
--- /dev/null
+How to update U-Boot on pico-imx7d board
+----------------------------------------
+
+Required software on the host PC:
+
+- imx_usb_loader: https://github.com/boundarydevices/imx_usb_loader
+
+Build U-Boot for pico:
+
+$ make mrproper
+$ make pico-imx7d_defconfig
+$ make
+
+This generates the U-Boot binary called u-boot.imx.
+
+Put pico board in USB download mode (refer to the PICO-iMX7D Quick Start Guide
+page 3)
+
+Connect a USB to serial adapter between the host PC and pico.
+
+Connect a USB cable between the OTG pico port and the host PC.
+
+Open a terminal program such as minicom.
+
+Copy u-boot.imx to the imx_usb_loader folder.
+
+Load u-boot.imx via USB:
+
+$ sudo ./imx_usb u-boot.imx
+
+Then U-Boot starts and its messages appear in the console program.
+
+Use the default environment variables:
+
+=> env default -f -a
+=> saveenv
+
+Run the UMS command:
+=> ums 0 mmc 0
+
+Transfer u-boot.imx to be flashed into the eMMC:
+
+$ sudo dd if=u-boot.imx of=/dev/sdX bs=1K seek=1; sync
+
+Remove power from the pico board.
+
+Put pico board into normal boot mode.
+
+Power up the board and the new updated U-Boot should boot from eMMC.
--- /dev/null
+/*
+ * Copyright (C) 2017 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+BOOT_FROM sd
+
+/* Secure boot support */
+#ifdef CONFIG_SECURE_BOOT
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type Address Value
+ *
+ * where:
+ * Addr-type register length (1,2 or 4 bytes)
+ * Address absolute address of the register
+ * value value to be stored in the register
+ */
+
+DATA 4 0x30340004 0x4F400005
+/* Clear then set bit30 to ensure exit from DDR retention */
+DATA 4 0x30360388 0x40000000
+DATA 4 0x30360384 0x40000000
+
+DATA 4 0x30391000 0x00000002
+DATA 4 0x307a0000 0x01040001
+DATA 4 0x307a01a0 0x80400003
+DATA 4 0x307a01a4 0x00100020
+DATA 4 0x307a01a8 0x80100004
+DATA 4 0x307a0064 0x00400046
+DATA 4 0x307a0490 0x00000001
+DATA 4 0x307a00d0 0x00020083
+DATA 4 0x307a00d4 0x00690000
+DATA 4 0x307a00dc 0x09300004
+DATA 4 0x307a00e0 0x04080000
+DATA 4 0x307a00e4 0x00100004
+DATA 4 0x307a00f4 0x0000033f
+DATA 4 0x307a0100 0x09081109
+DATA 4 0x307a0104 0x0007020d
+DATA 4 0x307a0108 0x03040407
+DATA 4 0x307a010c 0x00002006
+DATA 4 0x307a0110 0x04020205
+DATA 4 0x307a0114 0x03030202
+DATA 4 0x307a0120 0x00000803
+DATA 4 0x307a0180 0x00800020
+DATA 4 0x307a0184 0x02000100
+DATA 4 0x307a0190 0x02098204
+DATA 4 0x307a0194 0x00030303
+DATA 4 0x307a0200 0x00000016
+DATA 4 0x307a0204 0x00080808
+DATA 4 0x307a0210 0x00000f0f
+DATA 4 0x307a0214 0x07070707
+DATA 4 0x307a0218 0x0f070707
+DATA 4 0x307a0240 0x06000604
+DATA 4 0x307a0244 0x00000001
+DATA 4 0x30391000 0x00000000
+DATA 4 0x30790000 0x17420f40
+DATA 4 0x30790004 0x10210100
+DATA 4 0x30790010 0x00060807
+DATA 4 0x307900b0 0x1010007e
+DATA 4 0x3079009c 0x00000b24
+DATA 4 0x30790020 0x08080808
+DATA 4 0x30790030 0x08080808
+DATA 4 0x30790050 0x01000010
+DATA 4 0x30790050 0x00000010
+
+DATA 4 0x307900c0 0x0e407304
+DATA 4 0x307900c0 0x0e447304
+DATA 4 0x307900c0 0x0e447306
+
+CHECK_BITS_SET 4 0x307900c4 0x1
+
+DATA 4 0x307900c0 0x0e407304
+
+DATA 4 0x30384130 0x00000000
+DATA 4 0x30340020 0x00000178
+DATA 4 0x30384130 0x00000002
+DATA 4 0x30790018 0x0000000f
+
+CHECK_BITS_SET 4 0x307a0004 0x1
--- /dev/null
+/*
+ * Copyright (C) 2017 NXP Semiconductors
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx7-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/io.h>
+#include <common.h>
+#include <fsl_esdhc.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <mmc.h>
+#include <netdev.h>
+#include <usb.h>
+#include <power/pmic.h>
+#include <power/pfuze3000_pmic.h>
+#include "../../freescale/common/pfuze.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | \
+ PAD_CTL_PUS_PU100KOHM | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
+ PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
+
+#define ENET_PAD_CTRL (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
+#define ENET_PAD_CTRL_MII (PAD_CTL_DSE_3P3V_32OHM)
+
+#define ENET_RX_PAD_CTRL (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
+
+#define I2C_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
+ PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU100KOHM)
+
+#ifdef CONFIG_SYS_I2C_MXC
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+/* I2C4 for PMIC */
+static struct i2c_pads_info i2c_pad_info4 = {
+ .scl = {
+ .i2c_mode = MX7D_PAD_SAI1_RX_SYNC__I2C4_SCL | PC,
+ .gpio_mode = MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16 | PC,
+ .gp = IMX_GPIO_NR(6, 16),
+ },
+ .sda = {
+ .i2c_mode = MX7D_PAD_SAI1_RX_BCLK__I2C4_SDA | PC,
+ .gpio_mode = MX7D_PAD_SAI1_RX_BCLK__GPIO6_IO17 | PC,
+ .gp = IMX_GPIO_NR(6, 17),
+ },
+};
+#endif
+
+int dram_init(void)
+{
+ gd->ram_size = PHYS_SDRAM_SIZE;
+
+ return 0;
+}
+
+#ifdef CONFIG_POWER
+#define I2C_PMIC 3
+int power_init_board(void)
+{
+ struct pmic *p;
+ int ret;
+ unsigned int reg, rev_id;
+
+ ret = power_pfuze3000_init(I2C_PMIC);
+ if (ret)
+ return ret;
+
+ p = pmic_get("PFUZE3000");
+ ret = pmic_probe(p);
+ if (ret)
+ return ret;
+
+ pmic_reg_read(p, PFUZE3000_DEVICEID, ®);
+ pmic_reg_read(p, PFUZE3000_REVID, &rev_id);
+ printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id);
+
+ /* disable Low Power Mode during standby mode */
+ pmic_reg_read(p, PFUZE3000_LDOGCTL, ®);
+ reg |= 0x1;
+ pmic_reg_write(p, PFUZE3000_LDOGCTL, reg);
+
+ /* SW1A/1B mode set to APS/APS */
+ reg = 0x8;
+ pmic_reg_write(p, PFUZE3000_SW1AMODE, reg);
+ pmic_reg_write(p, PFUZE3000_SW1BMODE, reg);
+
+ /* SW1A/1B standby voltage set to 1.025V */
+ reg = 0xd;
+ pmic_reg_write(p, PFUZE3000_SW1ASTBY, reg);
+ pmic_reg_write(p, PFUZE3000_SW1BSTBY, reg);
+
+ /* decrease SW1B normal voltage to 0.975V */
+ pmic_reg_read(p, PFUZE3000_SW1BVOLT, ®);
+ reg &= ~0x1f;
+ reg |= PFUZE3000_SW1AB_SETP(975);
+ pmic_reg_write(p, PFUZE3000_SW1BVOLT, reg);
+
+ return 0;
+}
+#endif
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+ MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart5_pads[] = {
+ MX7D_PAD_I2C4_SCL__UART5_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX7D_PAD_I2C4_SDA__UART5_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc3_emmc_pads[] = {
+ MX7D_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX7D_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX7D_PAD_SD3_DATA0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX7D_PAD_SD3_DATA1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX7D_PAD_SD3_DATA2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX7D_PAD_SD3_DATA3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX7D_PAD_SD3_DATA4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX7D_PAD_SD3_DATA5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX7D_PAD_SD3_DATA6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX7D_PAD_SD3_DATA7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX7D_PAD_GPIO1_IO14__GPIO1_IO14 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+#ifdef CONFIG_FEC_MXC
+static iomux_v3_cfg_t const fec1_pads[] = {
+ MX7D_PAD_SD2_CD_B__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
+ MX7D_PAD_SD2_WP__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
+ MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+ MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+ MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+ MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+ MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+ MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+ MX7D_PAD_SD3_STROBE__GPIO6_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX7D_PAD_SD3_RESET_B__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+#define FEC1_RST_GPIO IMX_GPIO_NR(6, 11)
+
+static void setup_iomux_fec(void)
+{
+ imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
+
+ gpio_direction_output(FEC1_RST_GPIO, 0);
+ udelay(500);
+ gpio_set_value(FEC1_RST_GPIO, 1);
+}
+
+int board_eth_init(bd_t *bis)
+{
+ setup_iomux_fec();
+
+ return fecmxc_initialize_multi(bis, 0,
+ CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
+}
+
+static int setup_fec(void)
+{
+ struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
+ = (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
+
+ /* Use 125M anatop REF_CLK1 for ENET1, clear gpr1[13], gpr1[17] */
+ clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
+ (IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_MASK |
+ IOMUXC_GPR_GPR1_GPR_ENET1_CLK_DIR_MASK), 0);
+
+ return set_clk_enet(ENET_125MHz);
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+ unsigned short val;
+
+ /* To enable AR8035 ouput a 125MHz clk from CLK_25M */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
+
+ val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
+ val &= 0xffe7;
+ val |= 0x18;
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
+
+ /* introduce tx clock delay */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
+ val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
+ val |= 0x0100;
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
+
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
+#endif
+
+static void setup_iomux_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
+}
+
+static struct fsl_esdhc_cfg usdhc_cfg[1] = {
+ {USDHC3_BASE_ADDR},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ /* Assume uSDHC3 emmc is always present */
+ return 1;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc3_emmc_pads, ARRAY_SIZE(usdhc3_emmc_pads));
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+
+ return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+}
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+
+#ifdef CONFIG_SYS_I2C_MXC
+ setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info4);
+#endif
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_FEC_MXC
+ setup_fec();
+#endif
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+ struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
+
+ imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+
+ set_wdog_reset(wdog);
+
+ /*
+ * Do not assert internal WDOG_RESET_B_DEB(controlled by bit 4),
+ * since we use PMIC_PWRON to reset the board.
+ */
+ clrsetbits_le16(&wdog->wcr, 0, 0x10);
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: i.MX7D PICOSOM\n");
+
+ return 0;
+}
+
+int board_usb_phy_mode(int port)
+{
+ return USB_INIT_DEVICE;
+}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_MX7=y
+CONFIG_TARGET_PICO_IMX7D=y
+CONFIG_IMX_RDC=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/technexion/pico-imx7d/imximage.cfg"
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_BOOTD is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_G_DNL_MANUFACTURER="FSL"
+CONFIG_G_DNL_VENDOR_NUM=0x0525
+CONFIG_G_DNL_PRODUCT_NUM=0xa4a5
+CONFIG_OF_LIBFDT=y
--- /dev/null
+/*
+ * Copyright (C) 2017 NXP Semiconductors
+ *
+ * Configuration settings for the i.MX7D Pico board.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __PICO_IMX7D_CONFIG_H
+#define __PICO_IMX7D_CONFIG_H
+
+#include "mx7_common.h"
+
+#define PHYS_SDRAM_SIZE SZ_1G
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M)
+
+#define CONFIG_MXC_UART_BASE UART5_IPS_BASE_ADDR
+
+/* Network */
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define CONFIG_FEC_XCV_TYPE RGMII
+#define CONFIG_ETHPRIME "FEC"
+#define CONFIG_FEC_MXC_PHYADDR 1
+
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ATHEROS
+
+/* ENET1 */
+#define IMX_FEC_BASE ENET_IPS_BASE_ADDR
+
+/* MMC Config */
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+
+#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
+#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "script=boot.scr\0" \
+ "image=zImage\0" \
+ "console=ttymxc4\0" \
+ "fdt_high=0xffffffff\0" \
+ "initrd_high=0xffffffff\0" \
+ "fdt_file=imx7d-pico.dtb\0" \
+ "fdt_addr=0x83000000\0" \
+ "ip_dyn=yes\0" \
+ "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+ "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+ "finduuid=part uuid mmc 0:2 uuid\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate} " \
+ "root=PARTUUID=${uuid} rootwait rw\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run finduuid; " \
+ "run mmcargs; " \
+ "if run loadfdt; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi;\0" \
+ "netargs=setenv bootargs console=${console},${baudrate} " \
+ "root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${image}; " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "if mmc rescan; then " \
+ "if run loadimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "else run netboot; fi"
+
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x20000000)
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_SYS_HZ 1000
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* I2C configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1
+#define CONFIG_SYS_I2C_MXC_I2C2
+#define CONFIG_SYS_I2C_MXC_I2C3
+#define CONFIG_SYS_I2C_MXC_I2C4
+#define CONFIG_SYS_I2C_SPEED 100000
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE3000
+#define CONFIG_POWER_PFUZE3000_I2C_ADDR 0x08
+
+/* FLASH and environment organization */
+#define CONFIG_ENV_SIZE SZ_8K
+#define CONFIG_ENV_IS_IN_MMC
+
+#define CONFIG_ENV_OFFSET (8 * SZ_64K)
+#define CONFIG_SYS_FSL_USDHC_NUM 2
+
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_SYS_MMC_ENV_PART 0
+
+/* USB Configs */
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS 0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+
+#define CONFIG_IMX_THERMAL
+
+#define CONFIG_USB_FUNCTION_MASS_STORAGE
+
+#endif
projects / u-boot / commitdiff