CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
host
CONFIG_CMD_RUN run command in env variable
- CONFIG_CMD_SAVES * save S record dump
CONFIG_CMD_SDRAM * print SDRAM configuration information
(requires CONFIG_CMD_I2C)
CONFIG_CMD_SF * Read/write/erase SPI NOR flash
config ARCH_DAVINCI
bool "TI DaVinci"
select CPU_ARM926EJS
+ imply CMD_SAVES
help
Support for TI's DaVinci platform.
bool "Support spear300"
select CPU_ARM926EJS
select BOARD_EARLY_INIT_F
+ imply CMD_SAVES
config TARGET_SPEAR310
bool "Support spear310"
select CPU_ARM926EJS
select BOARD_EARLY_INIT_F
+ imply CMD_SAVES
config TARGET_SPEAR320
bool "Support spear320"
select CPU_ARM926EJS
select BOARD_EARLY_INIT_F
+ imply CMD_SAVES
config TARGET_SPEAR600
bool "Support spear600"
select CPU_ARM926EJS
select BOARD_EARLY_INIT_F
+ imply CMD_SAVES
config TARGET_STV0991
bool "Support stv0991"
select CMD_POWEROFF
imply CMD_MTDPARTS
imply FIT
+ imply CMD_SAVES
config ARCH_OMAP2PLUS
bool "TI OMAP2+"
Attachment, where AT refers to an IBM AT (Advanced Technology)
computer released in 1984.
+config CMD_SAVES
+ bool "saves - Save a file over serial in S-Record format"
+ help
+ Provides a way to save a binary file using the Motorola S-Record
+ format over the serial line.
+
config CMD_SF
bool "sf"
help
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_SAVES=y
CONFIG_CMD_RARP=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_ASKENV=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_MFSL=y
+CONFIG_CMD_SAVES=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_TFTPPUT=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_USB=y
CONFIG_CMD_FPGA_LOADMK=y
CONFIG_CMD_GPIO=y
+CONFIG_CMD_SAVES=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_AUTOBOOT_STOP_STR=" "
CONFIG_CMD_ASKENV=y
CONFIG_CRC32_VERIFY=y
+CONFIG_CMD_SAVES=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_DIAG=y
* Alphabetical list of all possible commands.
*/
-#define CONFIG_CMD_SAVES /* save S record dump */
#define CONFIG_CMD_SDRAM /* SDRAM DIMM SPD info printout */
#define CONFIG_CMD_TERMINAL /* built-in Serial Terminal */
#define CONFIG_CMD_UNIVERSE /* Tundra Universe Support */
"echo Product: $product; " \
"gpio c 1; gpio c 2;"
-/*
- * U-Boot commands
- */
-#define CONFIG_CMD_SAVES
-
-#ifndef CONFIG_DRIVER_TI_EMAC
-#endif
-
/* additions for new relocation code, must added to all boards */
#define CONFIG_SYS_SDRAM_BASE 0xc0000000
/* initial stack pointer in internal SRAM */
"mem=32M console=ttyS2,115200n8 root=/dev/mtdblock2 rw noinitrd ip=dhcp"
#define CONFIG_EXTRA_ENV_SETTINGS "hwconfig=dsp:wake=yes"
-/*
- * U-Boot commands
- */
-#define CONFIG_CMD_SAVES
-
#ifdef CONFIG_CMD_BDI
#define CONFIG_CLOCKS
#endif
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
-/*
- * U-Boot commands
- */
-#define CONFIG_CMD_SAVES
-
#ifdef CONFIG_CMD_BDI
#define CONFIG_CLOCKS
#endif
#define CONFIG_ENV_SPI_MAX_HZ 15000000
#ifndef MINIMAL_LOADER
-#define CONFIG_CMD_SAVES
#endif
/* NAND flash */
"nand write c0000100 180000 20000\0" \
"\0"
-/*
- * U-Boot commands
- */
-#define CONFIG_CMD_SAVES
-
#ifdef CONFIG_CMD_BDI
#define CONFIG_CLOCKS
#endif
"loadbootscr=fatload mmc 0 ${bootscraddr} boot.scr\0" \
"bootscript=source ${bootscraddr}\0" \
-/*
- * U-Boot commands
- */
-#define CONFIG_CMD_SAVES
-
#ifdef CONFIG_CMD_BDI
#define CONFIG_CLOCKS
#endif
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
-/*
- * Command line configuration.
- */
-
-#if defined(FLASH)
-# if !defined(RAMENV)
-# define CONFIG_CMD_SAVES
-# endif
-
-#else
-#if defined(SPIFLASH)
-
-# if !defined(RAMENV)
-# define CONFIG_CMD_SAVES
-# endif
-#endif
-#endif
-
#if defined(CONFIG_CMD_JFFS2)
# define CONFIG_MTD_PARTITIONS
#endif
"boot_fit=0\0" \
"console=ttyS2,115200n8\0"
-/*
- * U-Boot commands
- */
-#define CONFIG_CMD_SAVES
#ifdef CONFIG_CMD_BDI
#define CONFIG_CLOCKS
#endif
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_ONFI_DETECTION
-/*
- * Command support defines
- */
-#define CONFIG_CMD_SAVES
-
/*
* Default Environment Varible definitions
*/
#define CONFIG_DEV_USB_PHY_BASE KS2_DEV_USB_PHY_BASE
#define CONFIG_USB_PHY_CFG_BASE KS2_USB_PHY_CFG_BASE
-/* U-Boot command configuration */
-#define CONFIG_CMD_SAVES
-
/* U-Boot general configuration */
#define CONFIG_MISC_INIT_R
#define CONFIG_MX_CYCLIC
#define CONFIG_USB_EHCI_SPEAR
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
-/*
- * Command support defines
- */
-#define CONFIG_CMD_SAVES
-
/* Filesystem support (for USB key) */
#define CONFIG_SUPPORT_VFAT
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-/*=================*/
-/* U-Boot commands */
-/*=================*/
-
-#define CONFIG_CMD_SAVES
-
/*==============================*/
/* U-Boot autoboot configuration */
/*==============================*/
CONFIG_CMDLINE_EDITING
CONFIG_CMDLINE_PS_SUPPORT
CONFIG_CMDLINE_TAG
-CONFIG_CMD_SAVES
CONFIG_CMD_SCSI
CONFIG_CMD_SDRAM
CONFIG_CMD_SF_TEST