CONFIG_MMC_OMAP_HS=y
CONFIG_NAND=y
CONFIG_DRIVER_TI_CPSW=y
+CONFIG_PHY_ADDR_ENABLE=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_USB=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_MMC_OMAP_HS=y
CONFIG_DRIVER_TI_CPSW=y
+CONFIG_PHY_ADDR_ENABLE=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_FAT_WRITE=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_MMC_OMAP_HS=y
CONFIG_DRIVER_TI_CPSW=y
+CONFIG_PHY_ADDR_ENABLE=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_FAT_WRITE=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_MMC_OMAP_HS=y
CONFIG_DRIVER_TI_CPSW=y
+CONFIG_PHY_ADDR_ENABLE=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_FAT_WRITE=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_MMC_OMAP_HS=y
CONFIG_DRIVER_TI_CPSW=y
+CONFIG_PHY_ADDR_ENABLE=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_FAT_WRITE=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_MMC_OMAP_HS=y
CONFIG_DRIVER_TI_CPSW=y
+CONFIG_PHY_ADDR_ENABLE=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_FAT_WRITE=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_MMC_OMAP_HS=y
CONFIG_DRIVER_TI_CPSW=y
+CONFIG_PHY_ADDR_ENABLE=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_FAT_WRITE=y
CONFIG_NAND=y
CONFIG_SPL_NAND_SIMPLE=y
CONFIG_PHYLIB=y
+CONFIG_PHY_ADDR_ENABLE=y
CONFIG_PHY_ADDR=31
CONFIG_DM_SERIAL=y
CONFIG_SYS_NS16550=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_PHY_ADDR_ENABLE=y
CONFIG_PHY_GIGE=y
CONFIG_MVNETA=y
CONFIG_PCI=y
CONFIG_DM_GPIO=y
CONFIG_DM_MMC=y
CONFIG_MMC_MESON_GX=y
+CONFIG_PHY_ADDR_ENABLE=y
CONFIG_PHY_ADDR=8
CONFIG_PHY_MESON_GXL=y
CONFIG_DM_ETH=y
CONFIG_DM_GPIO=y
CONFIG_DM_MMC=y
CONFIG_MMC_MESON_GX=y
+CONFIG_PHY_ADDR_ENABLE=y
CONFIG_PHY_ADDR=8
CONFIG_PHY_MESON_GXL=y
CONFIG_DM_ETH=y
CONFIG_DM_GPIO=y
CONFIG_DM_MMC=y
CONFIG_MMC_MESON_GX=y
+CONFIG_PHY_ADDR_ENABLE=y
CONFIG_PHY_ADDR=8
CONFIG_PHY_MESON_GXL=y
CONFIG_DM_ETH=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
CONFIG_DRIVER_TI_CPSW=y
+CONFIG_PHY_ADDR_ENABLE=y
CONFIG_NETDEVICES=y
CONFIG_SYS_NS16550=y
CONFIG_OMAP3_SPI=y
CONFIG_DM_GPIO=y
# CONFIG_MMC is not set
CONFIG_PHYLIB=y
+CONFIG_PHY_ADDR_ENABLE=y
CONFIG_DM_SERIAL=y
CONFIG_SYS_NS16550=y
CONFIG_LPC32XX_SSP=y
CONFIG_SYS_I2C_DW=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
+CONFIG_PHY_ADDR_ENABLE=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
CONFIG_NETDEVICES=y
if PHYLIB
+config PHY_ADDR_ENABLE
+ bool "Limit phy address"
+ default y if ARCH_SUNXI
+ help
+ Select this if you want to control which phy address is used
+
+if PHY_ADDR_ENABLE
config PHY_ADDR
int "PHY address"
default 1 if ARCH_SUNXI
default 0
help
The address of PHY on MII bus. Usually in range of 0 to 31.
+endif
config B53_SWITCH
bool "Broadcom BCM53xx (RoboSwitch) Ethernet switch PHY support."