+++ /dev/null
-/*
- * Copyright 2007-2012 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <pci.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/cache.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_pci.h>
-#include <fsl_ddr_sdram.h>
-#include <asm/io.h>
-#include <asm/fsl_serdes.h>
-#include <miiphy.h>
-#include <libfdt.h>
-#include <fdt_support.h>
-#include <fsl_mdio.h>
-#include <tsec.h>
-#include <asm/fsl_law.h>
-#include <netdev.h>
-
-#include "../common/ngpixis.h"
-#include "../common/sgmii_riser.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
-#ifdef CONFIG_MMC
- ccsr_gur_t *gur = (ccsr_gur_t *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-
- setbits_be32(&gur->pmuxcr,
- (MPC85xx_PMUXCR_SDHC_CD |
- MPC85xx_PMUXCR_SDHC_WP));
-#endif
-
- return 0;
-}
-
-int checkboard(void)
-{
- u8 sw;
-
- printf("Board: P2020DS Sys ID: 0x%02x, "
- "Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
- in_8(&pixis->id), in_8(&pixis->arch), in_8(&pixis->scver));
-
- sw = in_8(&PIXIS_SW(PIXIS_LBMAP_SWITCH));
- sw = (sw & PIXIS_LBMAP_MASK) >> PIXIS_LBMAP_SHIFT;
-
- if (sw < 0x8)
- /* The lower two bits are the actual vbank number */
- printf("vBank: %d\n", sw & 3);
- else
- puts("Promjet\n");
-
- return 0;
-}
-
-#if !defined(CONFIG_DDR_SPD)
-/*
- * Fixed sdram init -- doesn't use serial presence detect.
- */
-
-phys_size_t fixed_sdram(void)
-{
- struct ccsr_ddr __iomem *ddr =
- (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
- uint d_init;
-
- ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
- ddr->timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
- ddr->timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
- ddr->sdram_mode = CONFIG_SYS_DDR_MODE_1;
- ddr->sdram_mode_2 = CONFIG_SYS_DDR_MODE_2;
- ddr->sdram_md_cntl = CONFIG_SYS_DDR_MODE_CTRL;
- ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL;
- ddr->sdram_data_init = CONFIG_SYS_DDR_DATA_INIT;
- ddr->sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL;
- ddr->sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL2;
- ddr->ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CNTL;
- ddr->ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CNTL;
- ddr->ddr_cdr1 = CONFIG_SYS_DDR_CDR1;
- ddr->timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4;
- ddr->timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5;
-
- if (!strcmp("performance", getenv("perf_mode"))) {
- /* Performance Mode Values */
-
- ddr->cs1_config = CONFIG_SYS_DDR_CS1_CONFIG_PERF;
- ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS_PERF;
- ddr->cs1_bnds = CONFIG_SYS_DDR_CS1_BNDS_PERF;
- ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_PERF;
- ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_PERF;
-
- asm("sync;isync");
-
- udelay(500);
-
- ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL_PERF;
- } else {
- /* Stable Mode Values */
-
- ddr->cs1_config = CONFIG_SYS_DDR_CS1_CONFIG;
- ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
- ddr->cs1_bnds = CONFIG_SYS_DDR_CS1_BNDS;
- ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
- ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
-
- /* ECC will be assumed in stable mode */
- ddr->err_int_en = CONFIG_SYS_DDR_ERR_INT_EN;
- ddr->err_disable = CONFIG_SYS_DDR_ERR_DIS;
- ddr->err_sbe = CONFIG_SYS_DDR_SBE;
-
- asm("sync;isync");
-
- udelay(500);
-
- ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL;
- }
-
-#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
- d_init = 1;
- debug("DDR - 1st controller: memory initializing\n");
- /*
- * Poll until memory is initialized.
- * 512 Meg at 400 might hit this 200 times or so.
- */
- while ((ddr->sdram_cfg_2 & (d_init << 4)) != 0)
- udelay(1000);
- debug("DDR: memory initialized\n\n");
- asm("sync; isync");
- udelay(500);
-#endif
-
- if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE,
- CONFIG_SYS_SDRAM_SIZE * 1024 * 1024,
- LAW_TRGT_IF_DDR) < 0) {
- printf("ERROR setting Local Access Windows for DDR\n");
- return 0;
- };
-
- return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
-}
-
-#endif
-
-#ifdef CONFIG_PCI
-void pci_init_board(void)
-{
- fsl_pcie_init_board(0);
-}
-#endif
-
-int board_early_init_r(void)
-{
- const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
- int flash_esel = find_tlb_idx((void *)flashbase, 1);
-
- /*
- * Remap Boot flash + PROMJET region to caching-inhibited
- * so that flash can be erased properly.
- */
-
- /* Flush d-cache and invalidate i-cache of any FLASH data */
- flush_dcache();
- invalidate_icache();
-
- if (flash_esel == -1) {
- /* very unlikely unless something is messed up */
- puts("Error: Could not find TLB for FLASH BASE\n");
- flash_esel = 2; /* give our best effort to continue */
- } else {
- /* invalidate existing TLB entry for flash + promjet */
- disable_tlb(flash_esel);
- }
-
- set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, flash_esel, BOOKE_PAGESZ_256M, 1);
-
- return 0;
-}
-
-#ifdef CONFIG_TSEC_ENET
-int board_eth_init(bd_t *bis)
-{
- struct fsl_pq_mdio_info mdio_info;
- struct tsec_info_struct tsec_info[4];
- int num = 0;
-
-#ifdef CONFIG_TSEC1
- SET_STD_TSEC_INFO(tsec_info[num], 1);
- num++;
-#endif
-#ifdef CONFIG_TSEC2
- SET_STD_TSEC_INFO(tsec_info[num], 2);
- if (is_serdes_configured(SGMII_TSEC2)) {
- puts("eTSEC2 is in sgmii mode.\n");
- tsec_info[num].flags |= TSEC_SGMII;
- }
- num++;
-#endif
-#ifdef CONFIG_TSEC3
- SET_STD_TSEC_INFO(tsec_info[num], 3);
- if (is_serdes_configured(SGMII_TSEC3)) {
- puts("eTSEC3 is in sgmii mode.\n");
- tsec_info[num].flags |= TSEC_SGMII;
-}
- num++;
-#endif
-
- if (!num) {
- printf("No TSECs initialized\n");
-
- return 0;
- }
-
-#ifdef CONFIG_FSL_SGMII_RISER
- fsl_sgmii_riser_init(tsec_info, num);
-#endif
-
- mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
- mdio_info.name = DEFAULT_MII_NAME;
-
- fsl_pq_mdio_init(bis, &mdio_info);
-
- tsec_eth_init(bis, tsec_info, num);
-
- return pci_eth_init(bis);
-}
-#endif
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, bd_t *bd)
-{
- phys_addr_t base;
- phys_size_t size;
-
- ft_cpu_setup(blob, bd);
-
- base = getenv_bootm_low();
- size = getenv_bootm_size();
-
- fdt_fixup_memory(blob, (u64)base, (u64)size);
-
-#ifdef CONFIG_HAS_FSL_DR_USB
- fdt_fixup_dr_usb(blob, bd);
-#endif
-
- FT_FSL_PCI_SETUP;
-
-#ifdef CONFIG_FSL_SGMII_RISER
- fsl_sgmii_riser_fdt_fixup(blob);
-#endif
-
- return 0;
-}
-#endif
+++ /dev/null
-/*
- * Copyright 2008-2011 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
- /* TLB 0 - for temp stack in cache */
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
-
- /* TLB 1 */
- /* *I*** - Covers boot page */
- SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_4K, 1),
-
- /* *I*G* - CCSRBAR */
- SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 1, BOOKE_PAGESZ_1M, 1),
-
- /* W**G* - Flash/promjet, localbus */
- /* This will be changed to *I*G* after relocation to RAM. */
- SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
- MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
- 0, 2, BOOKE_PAGESZ_256M, 1),
-
- /* *I*G* - PCI */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 3, BOOKE_PAGESZ_1G, 1),
-
- /* *I*G* - PCI */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x40000000,
- CONFIG_SYS_PCIE3_MEM_PHYS + 0x40000000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 4, BOOKE_PAGESZ_256M, 1),
-
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x50000000,
- CONFIG_SYS_PCIE3_MEM_PHYS + 0x50000000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 5, BOOKE_PAGESZ_256M, 1),
-
- /* *I*G* - PCI I/O */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_IO_VIRT, CONFIG_SYS_PCIE3_IO_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 6, BOOKE_PAGESZ_256K, 1),
-
- /* *I*G - NAND */
- SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 7, BOOKE_PAGESZ_1M, 1),
-
- SET_TLB_ENTRY(1, PIXIS_BASE, PIXIS_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 8, BOOKE_PAGESZ_4K, 1),
-
-#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L2_ADDR)
- /* *I*G - L2SRAM */
- SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 9, BOOKE_PAGESZ_256K, 1),
- SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + 0x40000,
- CONFIG_SYS_INIT_L2_ADDR_PHYS + 0x40000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 10, BOOKE_PAGESZ_256K, 1),
-#endif
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
+++ /dev/null
-/*
- * Copyright 2007-2012 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * p2020ds board configuration file
- *
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include "../board/freescale/common/ics307_clk.h"
-
-#ifdef CONFIG_36BIT
-#define CONFIG_PHYS_64BIT
-#endif
-
-#ifdef CONFIG_SDCARD
-#define CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_SYS_TEXT_BASE 0xf8f40000
-#define CONFIG_RESET_VECTOR_ADDRESS 0xf8fffffc
-#endif
-
-#ifdef CONFIG_SPIFLASH
-#define CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_SYS_TEXT_BASE 0xf8f40000
-#define CONFIG_RESET_VECTOR_ADDRESS 0xf8fffffc
-#endif
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE 1 /* BOOKE */
-#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_P2020 1
-#define CONFIG_P2020DS 1
-#define CONFIG_MP 1 /* support multiple processors */
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xeff40000
-#endif
-
-#ifndef CONFIG_RESET_VECTOR_ADDRESS
-#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
-#endif
-
-#define CONFIG_SYS_SRIO
-#define CONFIG_SRIO1 /* SRIO port 1 */
-#define CONFIG_SRIO2 /* SRIO port 2 */
-
-#define CONFIG_FSL_ELBC 1 /* Has Enhanced localbus controller */
-#define CONFIG_PCI 1 /* Enable PCI/PCIE */
-#define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */
-#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */
-#define CONFIG_PCIE3 1 /* PCIE controler 3 (ULI bridge) */
-#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
-#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
-#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-
-#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
-#define CONFIG_E1000 1 /* Defind e1000 pci Ethernet card*/
-
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */
-#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() /* ddrclk for MPC85xx */
-#define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-
-#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */
-
-#define CONFIG_ENABLE_36BIT_PHYS 1
-
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_ADDR_MAP 1
-#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
-#endif
-
-#define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */
-#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00400000
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
-
-/*
- * Config the L2 Cache
- */
-#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_INIT_L2_ADDR_PHYS 0xff8f80000ull
-#else
-#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
-#endif
-#define CONFIG_SYS_L2_SIZE (512 << 10)
-#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
-
-#define CONFIG_SYS_CCSRBAR 0xffe00000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-
-/* DDR Setup */
-#define CONFIG_VERY_BIG_RAM
-#ifdef CONFIG_DDR2
-#define CONFIG_SYS_FSL_DDR2
-#else
-#define CONFIG_SYS_FSL_DDR3 1
-#endif
-
-/* ECC will be enabled based on perf_mode environment variable */
-/* #define CONFIG_DDR_ECC */
-
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_NUM_DDR_CONTROLLERS 1
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 2
-
-/* I2C addresses of SPD EEPROMs */
-#define CONFIG_DDR_SPD
-#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD EEPROM located on I2C bus 0 */
-#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
-
-/* These are used when DDR doesn't use SPD. */
-#define CONFIG_SYS_SDRAM_SIZE 1024 /* DDR is 1GB */
-
-/* Default settings for "stable" mode */
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F
-#define CONFIG_SYS_DDR_CS1_BNDS 0x00000000
-#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202
-#define CONFIG_SYS_DDR_CS1_CONFIG 0x00000000
-#define CONFIG_SYS_DDR_TIMING_3 0x00020000
-#define CONFIG_SYS_DDR_TIMING_0 0x00330804
-#define CONFIG_SYS_DDR_TIMING_1 0x6f6b4846
-#define CONFIG_SYS_DDR_TIMING_2 0x0fa890d4
-#define CONFIG_SYS_DDR_MODE_1 0x00421422
-#define CONFIG_SYS_DDR_MODE_2 0x00000000
-#define CONFIG_SYS_DDR_MODE_CTRL 0x00000000
-#define CONFIG_SYS_DDR_INTERVAL 0x61800100
-#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
-#define CONFIG_SYS_DDR_CLK_CTRL 0x02000000
-#define CONFIG_SYS_DDR_TIMING_4 0x00220001
-#define CONFIG_SYS_DDR_TIMING_5 0x03402400
-#define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600
-#define CONFIG_SYS_DDR_WRLVL_CNTL 0x8655A608
-#define CONFIG_SYS_DDR_CONTROL 0xE7000000 /* Type = DDR3: ECC enabled, No Interleaving */
-#define CONFIG_SYS_DDR_CONTROL2 0x24400011
-#define CONFIG_SYS_DDR_CDR1 0x00040000
-#define CONFIG_SYS_DDR_CDR2 0x00000000
-
-#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d
-#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
-#define CONFIG_SYS_DDR_SBE 0x00010000
-
-/* Settings that differ for "performance" mode */
-#define CONFIG_SYS_DDR_CS0_BNDS_PERF 0x0000007F /* Interleaving Enabled */
-#define CONFIG_SYS_DDR_CS1_BNDS_PERF 0x00000000 /* Interleaving Enabled */
-#define CONFIG_SYS_DDR_CS1_CONFIG_PERF 0x80014202
-#define CONFIG_SYS_DDR_TIMING_1_PERF 0x5d5b4543
-#define CONFIG_SYS_DDR_TIMING_2_PERF 0x0fa890ce
-#define CONFIG_SYS_DDR_CONTROL_PERF 0xC7004000 /* Type = DDR3: ECC disabled, cs0-cs1 interleaving */
-
-/*
- * The following set of values were tested for DDR2
- * with a DDR3 to DDR2 interposer
- *
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-#define CONFIG_SYS_DDR_TIMING_0 0x00260802
-#define CONFIG_SYS_DDR_TIMING_1 0x3935d322
-#define CONFIG_SYS_DDR_TIMING_2 0x14904cc8
-#define CONFIG_SYS_DDR_MODE_1 0x00480432
-#define CONFIG_SYS_DDR_MODE_2 0x00000000
-#define CONFIG_SYS_DDR_INTERVAL 0x06180100
-#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
-#define CONFIG_SYS_DDR_CLK_CTRL 0x03800000
-#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
-#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000
-#define CONFIG_SYS_DDR_CONTROL 0xC3008000
-#define CONFIG_SYS_DDR_CONTROL2 0x04400010
- *
- */
-
-/*
- * Memory map
- *
- * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
- * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
- * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
- * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
- *
- * Localbus cacheable (TBD)
- * 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable
- *
- * Localbus non-cacheable
- * 0xe000_0000 0xe80f_ffff Promjet/free 128M non-cacheable
- * 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable
- * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable
- * 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0
- * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
- * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
- */
-
-/*
- * Local Bus Definitions
- */
-#define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull
-#else
-#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
-#endif
-
-#define CONFIG_FLASH_BR_PRELIM \
- (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000) | BR_PS_16 | BR_V)
-#define CONFIG_FLASH_OR_PRELIM 0xf8000ff7
-
-#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
-#define CONFIG_SYS_OR1_PRELIM 0xf8000ff7
-
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
-
-#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
-
-#define CONFIG_HWCONFIG /* enable hwconfig */
-#define CONFIG_FSL_NGPIXIS /* use common ngPIXIS code */
-
-#ifdef CONFIG_FSL_NGPIXIS
-#define PIXIS_BASE 0xffdf0000 /* PIXIS registers */
-#ifdef CONFIG_PHYS_64BIT
-#define PIXIS_BASE_PHYS 0xfffdf0000ull
-#else
-#define PIXIS_BASE_PHYS PIXIS_BASE
-#endif
-
-#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
-#define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */
-
-#define PIXIS_LBMAP_SWITCH 7
-#define PIXIS_LBMAP_MASK 0xf0
-#define PIXIS_LBMAP_SHIFT 4
-#define PIXIS_LBMAP_ALTBANK 0x20
-#endif
-
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
-/* The assembler doesn't like typecast */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
- ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
- CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
-#else
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
-#endif
-#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
-
-#define CONFIG_SYS_NAND_BASE 0xffa00000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull
-#else
-#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
-#endif
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE,\
- CONFIG_SYS_NAND_BASE + 0x40000, \
- CONFIG_SYS_NAND_BASE + 0x80000,\
- CONFIG_SYS_NAND_BASE + 0xC0000}
-#define CONFIG_SYS_MAX_NAND_DEVICE 4
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_CMD_NAND 1
-#define CONFIG_NAND_FSL_ELBC 1
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-
-/* NAND flash config */
-#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
- | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
- | BR_PS_8 /* Port Size = 8bit */ \
- | BR_MS_FCM /* MSEL = FCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \
- | OR_FCM_PGS /* Large Page*/ \
- | OR_FCM_CSCT \
- | OR_FCM_CST \
- | OR_FCM_CHT \
- | OR_FCM_SCY_1 \
- | OR_FCM_TRLX \
- | OR_FCM_EHTR)
-
-#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
-#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
-#define CONFIG_SYS_BR2_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
-#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-
-#define CONFIG_SYS_BR4_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0x40000) \
- | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
- | BR_PS_8 /* Port Size = 8bit */ \
- | BR_MS_FCM /* MSEL = FCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_OR4_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-#define CONFIG_SYS_BR5_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0x80000) \
- | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
- | BR_PS_8 /* Port Size = 8bit */ \
- | BR_MS_FCM /* MSEL = FCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_OR5_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-
-#define CONFIG_SYS_BR6_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0xc0000) \
- | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
- | BR_PS_8 /* Port Size = 8bit */ \
- | BR_MS_FCM /* MSEL = FCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_OR6_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-
-/* Serial Port - controlled on board with jumper J8
- * open - index 2
- * shorted - index 1
- */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
-
-/*
- * I2C2 EEPROM
- */
-#define CONFIG_ID_EEPROM
-#ifdef CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#endif
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_BUS_NUM 0
-
-/*
- * eSPI - Enhanced SPI
- */
-#define CONFIG_FSL_ESPI
-
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_SPANSION
-
-#define CONFIG_CMD_SF
-#define CONFIG_SF_DEFAULT_SPEED 10000000
-#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-
-/* controller 3, Slot 1, tgtid 3, Base address b000 */
-#define CONFIG_SYS_PCIE3_NAME "Slot 1"
-#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull
-#else
-#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
-#endif
-#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
-#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull
-#else
-#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000
-#endif
-#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
-
-/* controller 2, direct to uli, tgtid 2, Base address 9000 */
-#define CONFIG_SYS_PCIE2_NAME "ULI"
-#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
-#else
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
-#endif
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull
-#else
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
-#endif
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
-
-/* controller 1, Slot 2, tgtid 1, Base address a000 */
-#define CONFIG_SYS_PCIE1_NAME "Slot 2"
-#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull
-#else
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
-#endif
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull
-#else
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000
-#endif
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-
-#if defined(CONFIG_PCI)
-
-/*PCIE video card used*/
-#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT
-
-/* video */
-#undef CONFIG_VIDEO
-
-#if defined(CONFIG_VIDEO)
-#define CONFIG_BIOSEMU
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_SW_CURSOR
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_ATI_RADEON_FB
-#define CONFIG_VIDEO_LOGO
-/*#define CONFIG_CONSOLE_CURSOR*/
-#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
-#endif
-
-/* SRIO1 uses the same window as PCIE2 mem window */
-#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
-#else
-#define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000
-#endif
-#define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */
-
-/* SRIO2 uses the same window as PCIE1 mem window */
-#define CONFIG_SYS_SRIO2_MEM_VIRT 0xc0000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc40000000ull
-#else
-#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc0000000
-#endif
-#define CONFIG_SYS_SRIO2_MEM_SIZE 0x20000000 /* 512M */
-
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
-#define CONFIG_SCSI_AHCI
-
-#ifdef CONFIG_SCSI_AHCI
-#define CONFIG_LIBATA
-#define CONFIG_SATA_ULI5288
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
-#define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE
-#endif /* SCSI */
-
-#endif /* CONFIG_PCI */
-
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC1"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC2"
-#define CONFIG_TSEC3 1
-#define CONFIG_TSEC3_NAME "eTSEC3"
-
-#define CONFIG_FSL_SGMII_RISER 1
-#define SGMII_RISER_PHY_OFFSET 0x1b
-
-#ifdef CONFIG_FSL_SGMII_RISER
-#define CONFIG_SYS_TBIPA_VALUE 0x10 /* avoid conflict with eTSEC4 paddr */
-#endif
-
-#define TSEC1_PHY_ADDR 0
-#define TSEC2_PHY_ADDR 1
-#define TSEC3_PHY_ADDR 2
-
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#define TSEC3_PHYIDX 0
-
-#define CONFIG_ETHPRIME "eTSEC1"
-
-#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-#endif /* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-#if defined(CONFIG_SDCARD)
-#define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_FSL_FIXED_MMC_LOCATION
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#elif defined(CONFIG_SPIFLASH)
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SPI_BUS 0
-#define CONFIG_ENV_SPI_CS 0
-#define CONFIG_ENV_SPI_MAX_HZ 10000000
-#define CONFIG_ENV_SPI_MODE 0
-#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
-#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
-#define CONFIG_ENV_SECT_SIZE 0x10000
-#else
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_SETEXPR
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_SCSI
-#define CONFIG_CMD_EXT2
-#endif
-
-/*
- * USB
- */
-#define CONFIG_HAS_FSL_DR_USB
-#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#endif
-#endif
-
-/*
- * SDHC/MMC
- */
-#define CONFIG_MMC
-
-#ifdef CONFIG_MMC
-#define CONFIG_FSL_ESDHC
-#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_CMD_MMC
-#define CONFIG_GENERIC_MMC
-#endif
-
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-/* The mac addresses for all ethernet interface */
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#endif
-
-#define CONFIG_IPADDR 192.168.1.254
-
-#define CONFIG_HOSTNAME unknown
-#define CONFIG_ROOTPATH "/opt/nfsroot"
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
-
-#define CONFIG_SERVERIP 192.168.1.1
-#define CONFIG_GATEWAYIP 192.168.1.1
-#define CONFIG_NETMASK 255.255.255.0
-
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR 1000000
-
-#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-"perf_mode=performance\0" \
- "hwconfig=fsl_ddr:ctlr_intlv=bank,bank_intlv=cs0_cs1;" \
- "usb1:dr_mode=host,phy_type=ulpi\0" \
-"netdev=eth0\0" \
-"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
-"tftpflash=tftpboot $loadaddr $uboot; " \
- "protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
- "erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
- "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \
- "protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
- "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
-"satabootcmd=setenv bootargs root=/dev/$bdev rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr" \
-"consoledev=ttyS0\0" \
-"ramdiskaddr=2000000\0" \
-"ramdiskfile=p2020ds/ramdisk.uboot\0" \
-"fdtaddr=c00000\0" \
-"othbootargs=cache-sram-size=0x10000\0" \
-"fdtfile=p2020ds/p2020ds.dtb\0" \
-"bdev=sda3\0" \
-"partition=scsi 0:0\0"
-
-#define CONFIG_HDBOOT \
- "setenv bootargs root=/dev/$bdev rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "ext2load $partition $loadaddr $bootfile;" \
- "ext2load $partition $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT
-
-#endif /* __CONFIG_H */
projects / u-boot / commitdiff