mx28evk: Move README file inside board directory

Board specific READMEs should be located inside the respective board directory.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

diff --git a/board/freescale/mx28evk/README b/board/freescale/mx28evk/README
new file mode 100644 (file)
index 0000000..524f3fc
--- /dev/null
+++ b/board/freescale/mx28evk/README
@@ -0,0 +1,46 @@
+FREESCALE MX28EVK
+==================
+
+Supported hardware: only MX28EVK rev D is supported in U-boot.
+
+Files of the MX28EVK port
+--------------------------
+
+arch/arm/cpu/arm926ejs/mxs/    - The CPU support code for the Freescale i.MX28
+arch/arm/include/asm/arch-mxs/ - Header files for the Freescale i.MX28
+board/freescale/mx28evk/       - MX28EVK board specific files
+include/configs/mx28evk.h      - MX28EVK configuration file
+
+Jumper configuration
+---------------------
+
+To boot MX28EVK from an SD card, set the boot mode DIP switches as:
+
+   * Boot Mode Select: 1 0 0 1 (Boot from SD card Slot 0 - U42)
+   * JTAG PSWITCH RESET: To the right (reset disabled)
+   * Battery Source: Down
+   * Wall 5V: Up
+   * VDD 5V: To the left (off)
+   * Hold Button: Down (off)
+
+
+Environment Storage
+-------------------
+
+There are two targets for mx28evk:
+
+"make mx28evk_config"          - store enviroment variables into MMC
+
+or
+
+"make mx28evk_nand_config"     - store enviroment variables into NAND flash
+
+Choose the target accordingly.
+
+Note: The mx28evk board does not come with a NAND flash populated from the
+factory. It comes with an empty slot (U23), which allows the insertion of a
+48-pin TSOP flash device.
+
+Follow the instructions from doc/README.mxs to generate a bootable SD card.
+
+Insert the SD card in slot 0, power up the board and U-boot will boot.

diff --git a/doc/README.mx28evk b/doc/README.mx28evk
deleted file mode 100644 (file)
index 524f3fc..0000000
--- a/doc/README.mx28evk
+++ /dev/null
@@ -1,46 +0,0 @@
-FREESCALE MX28EVK
-==================
-
-Supported hardware: only MX28EVK rev D is supported in U-boot.
-
-Files of the MX28EVK port
---------------------------
-
-arch/arm/cpu/arm926ejs/mxs/    - The CPU support code for the Freescale i.MX28
-arch/arm/include/asm/arch-mxs/ - Header files for the Freescale i.MX28
-board/freescale/mx28evk/       - MX28EVK board specific files
-include/configs/mx28evk.h      - MX28EVK configuration file
-
-Jumper configuration
----------------------
-
-To boot MX28EVK from an SD card, set the boot mode DIP switches as:
-
-   * Boot Mode Select: 1 0 0 1 (Boot from SD card Slot 0 - U42)
-   * JTAG PSWITCH RESET: To the right (reset disabled)
-   * Battery Source: Down
-   * Wall 5V: Up
-   * VDD 5V: To the left (off)
-   * Hold Button: Down (off)
-
-
-Environment Storage
--------------------
-
-There are two targets for mx28evk:
-
-"make mx28evk_config"          - store enviroment variables into MMC
-
-or
-
-"make mx28evk_nand_config"     - store enviroment variables into NAND flash
-
-Choose the target accordingly.
-
-Note: The mx28evk board does not come with a NAND flash populated from the
-factory. It comes with an empty slot (U23), which allows the insertion of a
-48-pin TSOP flash device.
-
-Follow the instructions from doc/README.mxs to generate a bootable SD card.
-
-Insert the SD card in slot 0, power up the board and U-boot will boot.