uniphier-ph1-ld4-ref.dtb \
uniphier-ph1-ld6b-ref.dtb \
uniphier-ph1-pro4-ref.dtb \
+ uniphier-ph1-pro5-4kbox.dtb \
uniphier-ph1-sld3-ref.dtb \
uniphier-ph1-sld8-ref.dtb
dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
--- /dev/null
+/*
+ * Device Tree Source for UniPhier PH1-Pro5 4KBOX Board (EVB-Pro5-4KBOX-M-V0)
+ *
+ * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/dts-v1/;
+/include/ "uniphier-ph1-pro5.dtsi"
+
+/ {
+ model = "UniPhier PH1-Pro5 4KBOX Board";
+ compatible = "socionext,ph1-pro5-4kbox", "socionext,ph1-pro5";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS1,115200";
+ stdout-path = &serial1;
+ };
+
+ aliases {
+ serial1 = &serial1;
+ serial2 = &serial2;
+ i2c0 = &i2c0;
+ i2c5 = &i2c5;
+ i2c6 = &i2c6;
+ };
+};
+
+&serial1 {
+ status = "okay";
+};
+
+&serial2 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+};
+
+/* for U-boot only */
+/ {
+ soc {
+ u-boot,dm-pre-reloc;
+ };
+};
+
+&serial1 {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl_uart1 {
+ u-boot,dm-pre-reloc;
+};
help
This enables support for UniPhier PH1-sLD8 SoC.
+config ARCH_UNIPHIER_PH1_PRO5
+ bool "UniPhier PH1-Pro5 SoC"
+ select UNIPHIER_SMP
+ depends on !ARCH_UNIPHIER_PH1_SLD3 && \
+ !ARCH_UNIPHIER_PH1_LD4 && \
+ !ARCH_UNIPHIER_PH1_SLD8
+ help
+ This enables support for UniPhier PH1-Pro5 SoC.
+
config MICRO_SUPPORT_CARD
bool "Use Micro Support Card"
help
led_puts("U1");
ph1_ld4_clk_init();
break;
+#endif
+#if defined(CONFIG_ARCH_UNIPHIER_PH1_PRO5)
+ case SOC_UNIPHIER_PH1_PRO5:
+ ph1_pro5_pin_init();
+ led_puts("U1");
+ ph1_pro5_clk_init();
+ break;
#endif
default:
break;
};
#endif
+#if defined(CONFIG_ARCH_UNIPHIER_PH1_PRO5)
+static const struct uniphier_board_data ph1_pro5_data = {
+ .dram_ch0_base = 0x80000000,
+ .dram_ch0_size = 0x20000000,
+ .dram_ch0_width = 32,
+ .dram_ch1_base = 0xa0000000,
+ .dram_ch1_size = 0x20000000,
+ .dram_ch1_width = 32,
+ .dram_freq = 1866,
+};
+#endif
+
struct uniphier_board_id {
const char *compatible;
const struct uniphier_board_data *param;
#if defined(CONFIG_ARCH_UNIPHIER_PH1_SLD8)
{ "socionext,ph1-sld8", &ph1_sld8_data, },
#endif
+#if defined(CONFIG_ARCH_UNIPHIER_PH1_PRO5)
+ { "socionext,ph1-pro5", &ph1_pro5_data, },
+#endif
};
const struct uniphier_board_data *uniphier_get_board_param(const void *fdt)
obj-$(CONFIG_ARCH_UNIPHIER_PH1_LD4) += boot-mode-ph1-ld4.o
obj-$(CONFIG_ARCH_UNIPHIER_PH1_PRO4) += boot-mode-ph1-ld4.o
obj-$(CONFIG_ARCH_UNIPHIER_PH1_SLD8) += boot-mode-ph1-ld4.o
+obj-$(CONFIG_ARCH_UNIPHIER_PH1_PRO5) += boot-mode-ph1-pro5.o
--- /dev/null
+/*
+ * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <linux/io.h>
+#include <mach/boot-device.h>
+#include <mach/sbc-regs.h>
+#include <mach/sg-regs.h>
+
+static struct boot_device_info boot_device_table[] = {
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 8, EraseSize 128KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 16, EraseSize 128KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 8, EraseSize 256KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 16, EraseSize 256KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 8, EraseSize 512KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 16, EraseSize 512KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 8, EraseSize 128KB, Addr 4)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 16, EraseSize 128MB, Addr 4)"},
+ {BOOT_DEVICE_NONE, "Reserved"},
+ {BOOT_DEVICE_NONE, "Reserved"},
+ {BOOT_DEVICE_NONE, "Reserved"},
+ {BOOT_DEVICE_NONE, "Reserved"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 8, EraseSize 512MB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 16, EraseSize 512KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 8, EraseSize 128KB, Addr 4)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 16, EraseSize 128KB, Addr 4)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 8, ONFI, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 16, ONFI, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 8, ONFI, Addr 4)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 16, ONFI, Addr 4)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 8, ONFI, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 16, ONFI, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 8, ONFI, Addr 4)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 16, ONFI, Addr 4)"},
+ {BOOT_DEVICE_NONE, "Reserved"},
+ {BOOT_DEVICE_MMC1, "eMMC Boot (1.8V)"},
+ {BOOT_DEVICE_NONE, "Reserved"},
+ {BOOT_DEVICE_NONE, "Reserved"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 8, EraseSize 128MB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 16, EraseSize 128KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 8, EraseSize 256KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 16, EraseSize 256KB, Addr 5)"},
+ { /* sentinel */ }
+};
+
+static int get_boot_mode_sel(void)
+{
+ return (readl(SG_PINMON0) >> 1) & 0x1f;
+}
+
+u32 ph1_pro5_boot_device(void)
+{
+ int boot_mode;
+
+ boot_mode = get_boot_mode_sel();
+
+ return boot_device_table[boot_mode].type;
+}
+
+void ph1_pro5_boot_mode_show(void)
+{
+ int mode_sel, i;
+
+ mode_sel = get_boot_mode_sel();
+
+ puts("Boot Mode Pin:\n");
+
+ for (i = 0; i < ARRAY_SIZE(boot_device_table); i++)
+ printf(" %c %02x %s\n", i == mode_sel ? '*' : ' ', i,
+ boot_device_table[i].info);
+}
case SOC_UNIPHIER_PH1_PRO4:
case SOC_UNIPHIER_PH1_SLD8:
return ph1_ld4_boot_device();
+#endif
+#if defined(CONFIG_ARCH_UNIPHIER_PH1_PRO5)
+ case SOC_UNIPHIER_PH1_PRO5:
+ return ph1_pro5_boot_device();
#endif
default:
return BOOT_DEVICE_NONE;
obj-$(CONFIG_ARCH_UNIPHIER_PH1_LD4) += clk-ph1-ld4.o
obj-$(CONFIG_ARCH_UNIPHIER_PH1_PRO4) += clk-ph1-pro4.o
obj-$(CONFIG_ARCH_UNIPHIER_PH1_SLD8) += clk-ph1-ld4.o
+obj-$(CONFIG_ARCH_UNIPHIER_PH1_PRO5) += clk-ph1-pro5.o
--- /dev/null
+/*
+ * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <linux/io.h>
+#include <mach/init.h>
+#include <mach/sc-regs.h>
+
+void ph1_pro5_clk_init(void)
+{
+ u32 tmp;
+
+ /* deassert reset */
+ tmp = readl(SC_RSTCTRL);
+#ifdef CONFIG_USB_XHCI_UNIPHIER
+ tmp |= SC_RSTCTRL_NRST_USB3B0 | SC_RSTCTRL_NRST_GIO;
+#endif
+#ifdef CONFIG_NAND_DENALI
+ tmp |= SC_RSTCTRL_NRST_NAND;
+#endif
+ writel(tmp, SC_RSTCTRL);
+ readl(SC_RSTCTRL); /* dummy read */
+
+#ifdef CONFIG_USB_XHCI_UNIPHIER
+ tmp = readl(SC_RSTCTRL2);
+ tmp |= SC_RSTCTRL2_NRST_USB3B1;
+ writel(tmp, SC_RSTCTRL2);
+ readl(SC_RSTCTRL2); /* dummy read */
+#endif
+
+ /* privide clocks */
+ tmp = readl(SC_CLKCTRL);
+#ifdef CONFIG_USB_XHCI_UNIPHIER
+ tmp |= SC_CLKCTRL_CEN_USB31 | SC_CLKCTRL_CEN_USB30 |
+ SC_CLKCTRL_CEN_GIO;
+#endif
+#ifdef CONFIG_NAND_DENALI
+ tmp |= SC_CLKCTRL_CEN_NAND;
+#endif
+ writel(tmp, SC_CLKCTRL);
+ readl(SC_CLKCTRL); /* dummy read */
+}
case SOC_UNIPHIER_PH1_SLD8:
ph1_ld4_boot_mode_show();
break;
+#endif
+#if defined(CONFIG_ARCH_UNIPHIER_PH1_PRO5)
+ case SOC_UNIPHIER_PH1_PRO5:
+ ph1_pro5_boot_mode_show();
+ break;
#endif
default:
break;
b init_uart
ph1_sld8_end:
#endif
+#if defined(CONFIG_ARCH_UNIPHIER_PH1_PRO5)
+#define PH1_PRO5_UART_CLK 73728000
+ cmp r1, #0x2A
+ bne ph1_pro5_end
+
+ sg_set_pinsel 47, 0, 4, 8, r0, r1 @ TXD0 -> TXD0
+ sg_set_pinsel 49, 0, 4, 8, r0, r1 @ TXD1 -> TXD1
+ sg_set_pinsel 51, 0, 4, 8, r0, r1 @ TXD2 -> TXD2
+ sg_set_pinsel 53, 0, 4, 8, r0, r1 @ TXD3 -> TXD3
+
+ ldr r0, =SG_LOADPINCTRL
+ mov r1, #1
+ str r1, [r0]
+
+ ldr r0, =SC_CLKCTRL
+ ldr r1, [r0]
+ orr r1, r1, #SC_CLKCTRL_CEN_PERI
+ str r1, [r0]
+
+ ldr r3, =DIV_ROUND(PH1_PRO5_UART_CLK, 16 * BAUDRATE)
+
+ b init_uart
+ph1_pro5_end:
+#endif
init_uart:
addruart r0, r1, r2
obj-$(CONFIG_ARCH_UNIPHIER_PH1_LD4) += early-clk-ph1-ld4.o
obj-$(CONFIG_ARCH_UNIPHIER_PH1_PRO4) += early-clk-ph1-ld4.o
obj-$(CONFIG_ARCH_UNIPHIER_PH1_SLD8) += early-clk-ph1-ld4.o
+obj-$(CONFIG_ARCH_UNIPHIER_PH1_PRO5) += early-clk-ph1-pro5.o
--- /dev/null
+/*
+ * Copyright (C) 2015 Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <linux/io.h>
+#include <mach/init.h>
+#include <mach/sc-regs.h>
+
+int ph1_pro5_early_clk_init(const struct uniphier_board_data *bd)
+{
+ u32 tmp;
+
+ /*
+ * deassert reset
+ * UMCA2: Ch1 (DDR3)
+ * UMCA1, UMC31: Ch0 (WIO1)
+ * UMCA0, UMC30: Ch0 (WIO0)
+ */
+ tmp = readl(SC_RSTCTRL4);
+ tmp |= SC_RSTCTRL4_NRST_UMCSB | SC_RSTCTRL4_NRST_UMCA2 |
+ SC_RSTCTRL4_NRST_UMCA1 | SC_RSTCTRL4_NRST_UMCA0 |
+ SC_RSTCTRL4_NRST_UMC31 | SC_RSTCTRL4_NRST_UMC30;
+ writel(tmp, SC_RSTCTRL4);
+ readl(SC_RSTCTRL); /* dummy read */
+
+ /* privide clocks */
+ tmp = readl(SC_CLKCTRL);
+ tmp |= SC_CLKCTRL_CEN_SBC | SC_CLKCTRL_CEN_PERI;
+ writel(tmp, SC_CLKCTRL);
+ tmp = readl(SC_CLKCTRL4);
+ tmp |= SC_CLKCTRL4_CEN_UMCSB | SC_CLKCTRL4_CEN_UMC1 |
+ SC_CLKCTRL4_CEN_UMC0;
+ writel(tmp, SC_CLKCTRL4);
+ readl(SC_CLKCTRL4); /* dummy read */
+
+ return 0;
+}
u32 ph1_sld3_boot_device(void);
u32 ph1_ld4_boot_device(void);
+u32 ph1_pro5_boot_device(void);
void ph1_sld3_boot_mode_show(void);
void ph1_ld4_boot_mode_show(void);
+void ph1_pro5_boot_mode_show(void);
#endif /* _ASM_BOOT_DEVICE_H_ */
int ph1_ld4_init(const struct uniphier_board_data *bd);
int ph1_pro4_init(const struct uniphier_board_data *bd);
int ph1_sld8_init(const struct uniphier_board_data *bd);
+int ph1_pro5_init(const struct uniphier_board_data *bd);
#if defined(CONFIG_MICRO_SUPPORT_CARD)
int ph1_sld3_sbc_init(const struct uniphier_board_data *bd);
int ph1_ld4_enable_dpll_ssc(const struct uniphier_board_data *bd);
int ph1_ld4_early_clk_init(const struct uniphier_board_data *bd);
+int ph1_pro5_early_clk_init(const struct uniphier_board_data *bd);
int ph1_sld3_early_pin_init(const struct uniphier_board_data *bd);
void ph1_ld4_pin_init(void);
void ph1_pro4_pin_init(void);
void ph1_sld8_pin_init(void);
+void ph1_pro5_pin_init(void);
void ph1_ld4_clk_init(void);
void ph1_pro4_clk_init(void);
+void ph1_pro5_clk_init(void);
#define pr_err(fmt, args...) printf(fmt, ##args)
#define SC_BASE_ADDR 0x61840000
#endif
+#define SC_DPLLOSCCTRL (SC_BASE_ADDR | 0x1110)
+#define SC_DPLLOSCCTRL_DPLLST (0x1 << 1)
+#define SC_DPLLOSCCTRL_DPLLEN (0x1 << 0)
+
#define SC_DPLLCTRL (SC_BASE_ADDR | 0x1200)
#define SC_DPLLCTRL_SSC_EN (0x1 << 31)
#define SC_DPLLCTRL_FOUTMODE_MASK (0xf << 16)
#define SC_RSTCTRL_NRST_ETHER (0x1 << 12)
#define SC_RSTCTRL_NRST_STDMAC (0x1 << 10)
#define SC_RSTCTRL_NRST_GIO (0x1 << 6)
+/* Pro4 or older */
#define SC_RSTCTRL_NRST_UMC1 (0x1 << 5)
#define SC_RSTCTRL_NRST_UMC0 (0x1 << 4)
#define SC_RSTCTRL_NRST_NAND (0x1 << 2)
#define SC_RSTCTRL3 (SC_BASE_ADDR | 0x2008)
+/* Pro5 or newer */
+#define SC_RSTCTRL4 (SC_BASE_ADDR | 0x200c)
+#define SC_RSTCTRL4_NRST_UMCSB (0x1 << 12) /* UMC system bus */
+#define SC_RSTCTRL4_NRST_UMCA2 (0x1 << 10) /* UMC ch2 standby */
+#define SC_RSTCTRL4_NRST_UMCA1 (0x1 << 9) /* UMC ch1 standby */
+#define SC_RSTCTRL4_NRST_UMCA0 (0x1 << 8) /* UMC ch0 standby */
+#define SC_RSTCTRL4_NRST_UMC31 (0x1 << 5) /* UMC ch1 */
+#define SC_RSTCTRL4_NRST_UMC30 (0x1 << 4) /* UMC ch0 */
+
#define SC_CLKCTRL (SC_BASE_ADDR | 0x2104)
#define SC_CLKCTRL_CEN_USB31 (0x1 << 17) /* USB3 #1 */
#define SC_CLKCTRL_CEN_USB30 (0x1 << 16) /* USB3 #0 */
#define SC_CLKCTRL_CEN_MIO (0x1 << 11)
#define SC_CLKCTRL_CEN_STDMAC (0x1 << 10)
#define SC_CLKCTRL_CEN_GIO (0x1 << 6)
+/* Pro4 or older */
#define SC_CLKCTRL_CEN_UMC (0x1 << 4)
#define SC_CLKCTRL_CEN_NAND (0x1 << 2)
#define SC_CLKCTRL_CEN_SBC (0x1 << 1)
#define SC_CLKCTRL_CEN_PERI (0x1 << 0)
+/* Pro5 or newer */
+#define SC_CLKCTRL4 (SC_BASE_ADDR | 0x210c)
+#define SC_CLKCTRL4_CEN_UMCSB (0x1 << 12) /* UMC system bus */
+#define SC_CLKCTRL4_CEN_UMC1 (0x1 << 1) /* UMC ch1 */
+#define SC_CLKCTRL4_CEN_UMC0 (0x1 << 0) /* UMC ch0 */
+
/* System reset control register */
#define SC_IRQTIMSET (SC_BASE_ADDR | 0x3000)
#define SC_SLFRSTSEL (SC_BASE_ADDR | 0x3010)
/* Pin Control */
#define SG_PINCTRL_BASE (SG_CTRL_BASE | 0x1000)
-/* Only for PH1-Pro4 */
+/* PH1-Pro4, PH1-Pro5 */
#define SG_LOADPINCTRL (SG_CTRL_BASE | 0x1700)
/* Input Enable */
obj-$(CONFIG_ARCH_UNIPHIER_PH1_LD4) += init-ph1-ld4.o
obj-$(CONFIG_ARCH_UNIPHIER_PH1_PRO4) += init-ph1-pro4.o
obj-$(CONFIG_ARCH_UNIPHIER_PH1_SLD8) += init-ph1-sld8.o
+obj-$(CONFIG_ARCH_UNIPHIER_PH1_PRO5) += init-ph1-pro5.o
--- /dev/null
+/*
+ * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <linux/compiler.h>
+#include <mach/init.h>
+#include <mach/micro-support-card.h>
+
+int ph1_pro5_init(const struct uniphier_board_data *bd)
+{
+ ph1_pro4_sbc_init(bd);
+
+ support_card_reset();
+
+ support_card_init();
+
+ led_puts("L0");
+
+ memconf_init(bd);
+
+ led_puts("L1");
+
+ ph1_pro5_early_clk_init(bd);
+
+ led_puts("L2");
+
+ led_puts("L3");
+
+#ifdef CONFIG_SPL_SERIAL_SUPPORT
+ preloader_console_init();
+#endif
+
+ led_puts("L4");
+
+ led_puts("L5");
+
+ return 0;
+}
case SOC_UNIPHIER_PH1_SLD8:
ph1_sld8_init(param);
break;
+#endif
+#if defined(CONFIG_ARCH_UNIPHIER_PH1_PRO5)
+ case SOC_UNIPHIER_PH1_PRO5:
+ ph1_pro5_init(param);
+ break;
#endif
default:
break;
obj-$(CONFIG_ARCH_UNIPHIER_PH1_LD4) += pinctrl-ph1-ld4.o
obj-$(CONFIG_ARCH_UNIPHIER_PH1_PRO4) += pinctrl-ph1-pro4.o
obj-$(CONFIG_ARCH_UNIPHIER_PH1_SLD8) += pinctrl-ph1-sld8.o
+obj-$(CONFIG_ARCH_UNIPHIER_PH1_PRO5) += pinctrl-ph1-pro5.o
--- /dev/null
+/*
+ * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <linux/io.h>
+#include <mach/init.h>
+#include <mach/sg-regs.h>
+
+void ph1_pro5_pin_init(void)
+{
+ /* Comment format: PAD Name -> Function Name */
+
+#ifdef CONFIG_NAND_DENALI
+ sg_set_pinsel(19, 0, 4, 8); /* XNFRE -> XNFRE */
+ sg_set_pinsel(20, 0, 4, 8); /* XNFWE -> XNFWE */
+ sg_set_pinsel(21, 0, 4, 8); /* NFALE -> NFALE */
+ sg_set_pinsel(22, 0, 4, 8); /* NFCLE -> NFCLE */
+ sg_set_pinsel(23, 0, 4, 8); /* XNFWP -> XNFWP */
+ sg_set_pinsel(24, 0, 4, 8); /* XNFCE0 -> XNFCE0 */
+ sg_set_pinsel(25, 0, 4, 8); /* NRYBY0 -> NRYBY0 */
+ sg_set_pinsel(26, 0, 4, 8); /* XNFCE1 -> XNFCE1 */
+ sg_set_pinsel(27, 0, 4, 8); /* NRYBY1 -> NRYBY1 */
+ sg_set_pinsel(28, 0, 4, 8); /* NFD0 -> NFD0 */
+ sg_set_pinsel(29, 0, 4, 8); /* NFD1 -> NFD1 */
+ sg_set_pinsel(30, 0, 4, 8); /* NFD2 -> NFD2 */
+ sg_set_pinsel(31, 0, 4, 8); /* NFD3 -> NFD3 */
+ sg_set_pinsel(32, 0, 4, 8); /* NFD4 -> NFD4 */
+ sg_set_pinsel(33, 0, 4, 8); /* NFD5 -> NFD5 */
+ sg_set_pinsel(34, 0, 4, 8); /* NFD6 -> NFD6 */
+ sg_set_pinsel(35, 0, 4, 8); /* NFD7 -> NFD7 */
+#endif
+
+#ifdef CONFIG_USB_XHCI_UNIPHIER
+ sg_set_pinsel(124, 0, 4, 8); /* USB0VBUS -> USB0VBUS */
+ sg_set_pinsel(125, 0, 4, 8); /* USB0OD -> USB0OD */
+ sg_set_pinsel(126, 0, 4, 8); /* USB1VBUS -> USB1VBUS */
+ sg_set_pinsel(127, 0, 4, 8); /* USB1OD -> USB1OD */
+#endif
+
+ writel(1, SG_LOADPINCTRL);
+}
obj-$(CONFIG_ARCH_UNIPHIER_PH1_LD4) += sbc-ph1-ld4.o
obj-$(CONFIG_ARCH_UNIPHIER_PH1_PRO4) += sbc-ph1-pro4.o
obj-$(CONFIG_ARCH_UNIPHIER_PH1_SLD8) += sbc-ph1-ld4.o
+obj-$(CONFIG_ARCH_UNIPHIER_PH1_PRO5) += sbc-ph1-pro4.o
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_UNIPHIER=y
+CONFIG_ARCH_UNIPHIER_PH1_PRO5=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_MICRO_SUPPORT_CARD=y
+CONFIG_SYS_TEXT_BASE=0x84000000
+CONFIG_DEFAULT_DEVICE_TREE="uniphier-ph1-pro5-4kbox"
+CONFIG_HUSH_PARSER=y
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_ENV_EXISTS is not set
+CONFIG_CMD_NAND=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_TIME=y
+# CONFIG_CMD_MISC is not set
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_SIMPLE_BUS=y
+CONFIG_NAND_DENALI=y
+CONFIG_SYS_NAND_DENALI_64BIT=y
+CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES=8
+CONFIG_SPL_NAND_DENALI=y
+CONFIG_UNIPHIER_SERIAL=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_STORAGE=y
$ make ph1_sld8_defconfig
$ make CROSS_COMPILE=arm-linux-gnueabi-
+PH1-Pro5:
+ $ make ph1_pro5_defconfig
+ $ make CROSS_COMPILE=arm-linux-gnueabi-
+
You may wish to change the "CROSS_COMPILE=arm-linux-gnueabi-"
to use your favorite compiler.
projects / u-boot / commitdiff