Move all of the status LED feature to drivers/led/Kconfig.
The LED status definitions were moved from the board configuration
files to the defconfig files.
TBD: Move all of the definitions in the include/status_led.h to the
relevant board's defconfig files.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
#include <config.h>
#include <status_led.h>
-static uint8_t saved_state[2] = {STATUS_LED_OFF, STATUS_LED_OFF};
-static uint32_t gpio_pin[2] = {1 << STATUS_LED_GREEN,
- 1 << STATUS_LED_RED};
+static uint8_t saved_state[2] = {CONFIG_LED_STATUS_OFF, CONFIG_LED_STATUS_OFF};
+static uint32_t gpio_pin[2] = {1 << CONFIG_LED_STATUS_GREEN,
+ 1 << CONFIG_LED_STATUS_RED};
static inline void switch_LED_on(uint8_t led)
{
register struct gpio_regs *gpio = (struct gpio_regs *)GPIO_BASE;
writel(readl(&gpio->pedr) | gpio_pin[led], &gpio->pedr);
- saved_state[led] = STATUS_LED_ON;
+ saved_state[led] = CONFIG_LED_STATUS_ON;
}
static inline void switch_LED_off(uint8_t led)
register struct gpio_regs *gpio = (struct gpio_regs *)GPIO_BASE;
writel(readl(&gpio->pedr) & ~gpio_pin[led], &gpio->pedr);
- saved_state[led] = STATUS_LED_OFF;
+ saved_state[led] = CONFIG_LED_STATUS_OFF;
}
void red_led_on(void)
{
- switch_LED_on(STATUS_LED_RED);
+ switch_LED_on(CONFIG_LED_STATUS_RED);
}
void red_led_off(void)
{
- switch_LED_off(STATUS_LED_RED);
+ switch_LED_off(CONFIG_LED_STATUS_RED);
}
void green_led_on(void)
{
- switch_LED_on(STATUS_LED_GREEN);
+ switch_LED_on(CONFIG_LED_STATUS_GREEN);
}
void green_led_off(void)
{
- switch_LED_off(STATUS_LED_GREEN);
+ switch_LED_off(CONFIG_LED_STATUS_GREEN);
}
void __led_init(led_id_t mask, int state)
void __led_toggle(led_id_t mask)
{
- if (STATUS_LED_RED == mask) {
- if (STATUS_LED_ON == saved_state[STATUS_LED_RED])
+ if (CONFIG_LED_STATUS_RED == mask) {
+ if (CONFIG_LED_STATUS_ON == saved_state[CONFIG_LED_STATUS_RED])
red_led_off();
else
red_led_on();
- } else if (STATUS_LED_GREEN == mask) {
- if (STATUS_LED_ON == saved_state[STATUS_LED_GREEN])
+ } else if (CONFIG_LED_STATUS_GREEN == mask) {
+ if (CONFIG_LED_STATUS_ON ==
+ saved_state[CONFIG_LED_STATUS_GREEN])
green_led_off();
else
green_led_on();
void __led_set(led_id_t mask, int state)
{
- if (STATUS_LED_RED == mask) {
- if (STATUS_LED_ON == state)
+ if (CONFIG_LED_STATUS_RED == mask) {
+ if (CONFIG_LED_STATUS_ON == state)
red_led_on();
else
red_led_off();
- } else if (STATUS_LED_GREEN == mask) {
- if (STATUS_LED_ON == state)
+ } else if (CONFIG_LED_STATUS_GREEN == mask) {
+ if (CONFIG_LED_STATUS_ON == state)
green_led_on();
else
green_led_off();
#define __ASM_STATUS_LED_H__
/* if not overridden */
-#ifndef CONFIG_BOARD_SPECIFIC_LED
+#ifndef CONFIG_LED_STATUS_BOARD_SPECIFIC
# if defined(CONFIG_8xx)
# include <mpc8xx.h>
# elif defined(CONFIG_MPC8260)
#endif
#if (STATUS_LED_ACTIVE == 0)
- if (state == STATUS_LED_ON)
+ if (state == CONFIG_LED_STATUS_ON)
immr->STATUS_LED_DAT &= ~mask;
else
immr->STATUS_LED_DAT |= mask;
#else
- if (state == STATUS_LED_ON)
+ if (state == CONFIG_LED_STATUS_ON)
immr->STATUS_LED_DAT |= mask;
else
immr->STATUS_LED_DAT &= ~mask;
volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
#if (STATUS_LED_ACTIVE == 0)
- if (state == STATUS_LED_ON)
+ if (state == CONFIG_LED_STATUS_ON)
immr->STATUS_LED_DAT &= ~mask;
else
immr->STATUS_LED_DAT |= mask;
#else
- if (state == STATUS_LED_ON)
+ if (state == CONFIG_LED_STATUS_ON)
immr->STATUS_LED_DAT |= mask;
else
immr->STATUS_LED_DAT &= ~mask;
#include <common.h>
#include <asm/processor.h>
#include <watchdog.h>
-#ifdef CONFIG_STATUS_LED
+#ifdef CONFIG_LED_STATUS
#include <status_led.h>
#endif
WATCHDOG_RESET ();
#endif /* CONFIG_WATCHDOG || CONFIG_HW_WATCHDOG */
-#ifdef CONFIG_STATUS_LED
+#ifdef CONFIG_LED_STATUS
status_led_tick (timestamp);
-#endif /* CONFIG_STATUS_LED */
+#endif /* CONFIG_LED_STATUS */
#ifdef CONFIG_SHOW_ACTIVITY
board_show_activity (timestamp);
void __led_set(led_id_t mask, int state)
{
- if (state == STATUS_LED_ON)
+ if (state == CONFIG_LED_STATUS_ON)
MCFGPTA_GPTPORT |= (1 << 3);
else
MCFGPTA_GPTPORT &= ~(1 << 3);
#ifdef CONFIG_SHOW_BOOT_PROGRESS
-#define STATUS_LED_OFF 0
-#define STATUS_LED_ON 1
+#define CONFIG_LED_STATUS_OFF 0
+#define CONFIG_LED_STATUS_ON 1
static int gpio_setup;
{
switch (status) {
case BOOTSTAGE_ID_CHECK_MAGIC:
- stamp_led_set(STATUS_LED_OFF, STATUS_LED_OFF, STATUS_LED_ON);
+ stamp_led_set(CONFIG_LED_STATUS_OFF, CONFIG_LED_STATUS_OFF,
+ CONFIG_LED_STATUS_ON);
break;
case BOOTSTAGE_ID_CHECK_HEADER:
- stamp_led_set(STATUS_LED_OFF, STATUS_LED_ON, STATUS_LED_OFF);
+ stamp_led_set(CONFIG_LED_STATUS_OFF, CONFIG_LED_STATUS_ON,
+ CONFIG_LED_STATUS_OFF);
break;
case BOOTSTAGE_ID_CHECK_CHECKSUM:
- stamp_led_set(STATUS_LED_OFF, STATUS_LED_ON, STATUS_LED_ON);
+ stamp_led_set(CONFIG_LED_STATUS_OFF, CONFIG_LED_STATUS_ON,
+ CONFIG_LED_STATUS_ON);
break;
case BOOTSTAGE_ID_CHECK_ARCH:
- stamp_led_set(STATUS_LED_ON, STATUS_LED_OFF, STATUS_LED_OFF);
+ stamp_led_set(CONFIG_LED_STATUS_ON, CONFIG_LED_STATUS_OFF,
+ CONFIG_LED_STATUS_OFF);
break;
case BOOTSTAGE_ID_CHECK_IMAGETYPE:
case BOOTSTAGE_ID_DECOMP_IMAGE:
- stamp_led_set(STATUS_LED_ON, STATUS_LED_OFF, STATUS_LED_ON);
+ stamp_led_set(CONFIG_LED_STATUS_ON, CONFIG_LED_STATUS_OFF,
+ CONFIG_LED_STATUS_ON);
break;
case BOOTSTAGE_ID_KERNEL_LOADED:
case BOOTSTAGE_ID_CHECK_BOOT_OS:
- stamp_led_set(STATUS_LED_ON, STATUS_LED_ON, STATUS_LED_OFF);
+ stamp_led_set(CONFIG_LED_STATUS_ON, CONFIG_LED_STATUS_ON,
+ CONFIG_LED_STATUS_OFF);
break;
case BOOTSTAGE_ID_BOOT_OS_RETURNED:
case BOOTSTAGE_ID_RD_MAGIC:
case BOOTSTAGE_ID_RAMDISK:
case BOOTSTAGE_ID_NO_RAMDISK:
case BOOTSTAGE_ID_RUN_OS:
- stamp_led_set(STATUS_LED_OFF, STATUS_LED_OFF, STATUS_LED_OFF);
+ stamp_led_set(CONFIG_LED_STATUS_OFF, CONFIG_LED_STATUS_OFF,
+ CONFIG_LED_STATUS_OFF);
break;
default:
- stamp_led_set(STATUS_LED_ON, STATUS_LED_ON, STATUS_LED_ON);
+ stamp_led_set(CONFIG_LED_STATUS_ON, CONFIG_LED_STATUS_ON,
+ CONFIG_LED_STATUS_ON);
break;
}
}
gpmc_init();
-#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
- status_led_set(STATUS_LED_BOOT, STATUS_LED_OFF);
+#if defined(CONFIG_LED_STATUS) && defined(CONFIG_LED_STATUS_BOOT_ENABLE)
+ status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_OFF);
#endif
return 0;
}
/* boot param addr */
gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
-#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
- status_led_set(STATUS_LED_BOOT, STATUS_LED_ON);
+#if defined(CONFIG_LED_STATUS) && defined(CONFIG_LED_STATUS_BOOT_ENABLE)
+ status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_ON);
#endif
return 0;
/* boot param addr */
gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
-#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
- status_led_set(STATUS_LED_BOOT, STATUS_LED_ON);
+#if defined(CONFIG_LED_STATUS) && defined(CONFIG_LED_STATUS_BOOT_ENABLE)
+ status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_ON);
#endif
cm_t3517_musb_init();
void __led_toggle(led_id_t mask)
{
int toggle_gpio = 0;
-#ifdef STATUS_LED_BIT
- if (!toggle_gpio && STATUS_LED_BIT & mask)
+#ifdef CONFIG_LED_STATUS0
+ if (!toggle_gpio && CONFIG_LED_STATUS_BIT & mask)
toggle_gpio = TRICORDER_STATUS_LED_GREEN;
#endif
-#ifdef STATUS_LED_BIT1
- if (!toggle_gpio && STATUS_LED_BIT1 & mask)
+#ifdef CONFIG_LED_STATUS1
+ if (!toggle_gpio && CONFIG_LED_STATUS_BIT1 & mask)
toggle_gpio = TRICORDER_STATUS_LED_YELLOW;
#endif
-#ifdef STATUS_LED_BIT2
- if (!toggle_gpio && STATUS_LED_BIT2 & mask) {
+#ifdef CONFIG_LED_STATUS2
+ if (!toggle_gpio && CONFIG_LED_STATUS_BIT2 & mask) {
uint8_t val;
twl4030_i2c_read_u8(TWL4030_CHIP_LED, TWL4030_LED_LEDEN,
&val);
void __led_set(led_id_t mask, int state)
{
-#ifdef STATUS_LED_BIT
- if (STATUS_LED_BIT & mask) {
+#ifdef CONFIG_LED_STATUS0
+ if (CONFIG_LED_STATUS_BIT & mask) {
gpio_request(TRICORDER_STATUS_LED_GREEN, "");
gpio_direction_output(TRICORDER_STATUS_LED_GREEN, 0);
gpio_set_value(TRICORDER_STATUS_LED_GREEN, state);
}
#endif
-#ifdef STATUS_LED_BIT1
- if (STATUS_LED_BIT1 & mask) {
+#ifdef CONFIG_LED_STATUS1
+ if (CONFIG_LED_STATUS_BIT1 & mask) {
gpio_request(TRICORDER_STATUS_LED_YELLOW, "");
gpio_direction_output(TRICORDER_STATUS_LED_YELLOW, 0);
gpio_set_value(TRICORDER_STATUS_LED_YELLOW, state);
}
#endif
-#ifdef STATUS_LED_BIT2
- if (STATUS_LED_BIT2 & mask) {
- if (STATUS_LED_OFF == state)
+#ifdef CONFIG_LED_STATUS2
+ if (CONFIG_LED_STATUS_BIT2 & mask) {
+ if (CONFIG_LED_STATUS_OFF == state)
twl4030_i2c_write_u8(TWL4030_CHIP_LED,
TWL4030_LED_LEDEN, 0);
else
print_hwversion(&eeprom);
twl4030_power_init();
- status_led_set(0, STATUS_LED_ON);
- status_led_set(1, STATUS_LED_ON);
- status_led_set(2, STATUS_LED_ON);
+ status_led_set(0, CONFIG_LED_STATUS_ON);
+ status_led_set(1, CONFIG_LED_STATUS_ON);
+ status_led_set(2, CONFIG_LED_STATUS_ON);
omap_die_id_display();
/* boot param addr */
gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
-#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
- status_led_set(STATUS_LED_BOOT, STATUS_LED_ON);
+#if defined(CONFIG_LED_STATUS) && defined(CONFIG_LED_STATUS_BOOT_ENABLE)
+ status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_ON);
#endif
return 0;
#include <miiphy.h>
#include <libfdt.h>
-#if defined(CONFIG_STATUS_LED)
+#if defined(CONFIG_LED_STATUS)
#include <status_led.h>
-#endif /* CONFIG_STATUS_LED */
+#endif /* CONFIG_LED_STATUS */
/* Kollmorgen DPR initialization data */
struct init_elem {
#endif /* CONFIG_OF_BOARD_SETUP */
-#if defined(CONFIG_STATUS_LED)
-void __led_init(led_id_t regaddr, int state)
+#if defined(CONFIG_LED_STATUS)
+vu_long *regcode_to_regaddr(led_id_t regcode)
{
- *((vu_long *) regaddr) |= ENABLE_GPIO_OUT;
+ /* GPT Enable and Mode Select Register address */
+ vu_long *reg_translate[] = {
+ (vu_long *)MPC5XXX_GPT6_ENABLE,
+ (vu_long *)MPC5XXX_GPT7_ENABLE,
+ };
+
+ if (ARRAY_SIZE(reg_translate) <= regcode)
+ return NULL;
+ return reg_translate[regcode];
+}
+
+void __led_init(led_id_t regcode, int state)
+{
+ vu_long *regaddr = regcode_to_regaddr(regcode);
+
+ *regaddr |= ENABLE_GPIO_OUT;
- if (state == STATUS_LED_ON)
+ if (state == CONFIG_LED_STATUS_ON)
*((vu_long *) regaddr) |= LED_ON;
else
*((vu_long *) regaddr) &= ~LED_ON;
}
-void __led_set(led_id_t regaddr, int state)
+void __led_set(led_id_t regcode, int state)
{
- if (state == STATUS_LED_ON)
- *((vu_long *) regaddr) |= LED_ON;
+ vu_long *regaddr = regcode_to_regaddr(regcode);
+
+ if (state == CONFIG_LED_STATUS_ON)
+ *regaddr |= LED_ON;
else
- *((vu_long *) regaddr) &= ~LED_ON;
+ *regaddr &= ~LED_ON;
}
-void __led_toggle(led_id_t regaddr)
+void __led_toggle(led_id_t regcode)
{
- *((vu_long *) regaddr) ^= LED_ON;
+ vu_long *regaddr = regcode_to_regaddr(regcode);
+
+ *regaddr ^= LED_ON;
}
-#endif /* CONFIG_STATUS_LED */
+#endif /* CONFIG_LED_STATUS */
#include <asm/arch/imx-regs.h>
#include <asm/arch/clock.h>
#include <asm/arch/sys_proto.h>
-#ifdef CONFIG_STATUS_LED
+#ifdef CONFIG_LED_STATUS
#include <status_led.h>
#endif
/* Adress of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
- status_led_set(STATUS_LED_BOOT, STATUS_LED_STATE);
+#if defined(CONFIG_LED_STATUS) && defined(CONFIG_LED_STATUS_BOOT_ENABLE)
+ status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_STATE);
#endif
return 0;
const unsigned int usb_nrst_gpio = 35;
int ret;
- status_led_set(1, STATUS_LED_ON);
- status_led_set(2, STATUS_LED_ON);
+ status_led_set(1, CONFIG_LED_STATUS_ON);
+ status_led_set(2, CONFIG_LED_STATUS_ON);
/* Address of boot parameters for ATAG (if ATAG is used) */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
#
obj-y := beagle.o
-obj-$(CONFIG_STATUS_LED) += led.o
+obj-$(CONFIG_LED_STATUS) += led.o
#include <common.h>
#include <dm.h>
#include <ns16550.h>
-#ifdef CONFIG_STATUS_LED
+#ifdef CONFIG_LED_STATUS
#include <status_led.h>
#endif
#include <twl4030.h>
/* boot param addr */
gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
-#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
- status_led_set (STATUS_LED_BOOT, STATUS_LED_ON);
+#if defined(CONFIG_LED_STATUS) && defined(CONFIG_LED_STATUS_BOOT_ENABLE)
+ status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_ON);
#endif
return 0;
#define BEAGLE_LED_USR0 150
#define BEAGLE_LED_USR1 149
-#ifdef STATUS_LED_GREEN
+#ifdef CONFIG_LED_STATUS_GREEN
void green_led_off(void)
{
- __led_set (STATUS_LED_GREEN, 0);
+ __led_set(CONFIG_LED_STATUS_GREEN, 0);
}
void green_led_on(void)
{
- __led_set (STATUS_LED_GREEN, 1);
+ __led_set(CONFIG_LED_STATUS_GREEN, 1);
}
#endif
static int get_led_gpio(led_id_t mask)
{
-#ifdef STATUS_LED_BIT
- if (STATUS_LED_BIT & mask)
+#ifdef CONFIG_LED_STATUS0
+ if (CONFIG_LED_STATUS_BIT & mask)
return BEAGLE_LED_USR0;
#endif
-#ifdef STATUS_LED_BIT1
- if (STATUS_LED_BIT1 & mask)
+#ifdef CONFIG_LED_STATUS1
+ if (CONFIG_LED_STATUS_BIT1 & mask)
return BEAGLE_LED_USR1;
#endif
obj-$(CONFIG_CMD_JFFS2) += jffs2.o
obj-$(CONFIG_CMD_CRAMFS) += cramfs.o
obj-$(CONFIG_CMD_LDRINFO) += ldrinfo.o
-obj-$(CONFIG_CMD_LED) += led.o
+obj-$(CONFIG_LED_STATUS_CMD) += led.o
obj-$(CONFIG_CMD_LICENSE) += license.o
obj-y += load.o
obj-$(CONFIG_LOGBUFFER) += log.o
#include <ide.h>
#include <ata.h>
-#ifdef CONFIG_STATUS_LED
+#ifdef CONFIG_LED_STATUS
# include <status_led.h>
#endif
typedef struct led_tbl_s led_tbl_t;
static const led_tbl_t led_commands[] = {
-#ifdef CONFIG_BOARD_SPECIFIC_LED
-#ifdef STATUS_LED_BIT
- { "0", STATUS_LED_BIT, NULL, NULL, NULL },
+#ifdef CONFIG_LED_STATUS_BOARD_SPECIFIC
+#ifdef CONFIG_LED_STATUS0
+ { "0", CONFIG_LED_STATUS_BIT, NULL, NULL, NULL },
#endif
-#ifdef STATUS_LED_BIT1
- { "1", STATUS_LED_BIT1, NULL, NULL, NULL },
+#ifdef CONFIG_LED_STATUS1
+ { "1", CONFIG_LED_STATUS_BIT1, NULL, NULL, NULL },
#endif
-#ifdef STATUS_LED_BIT2
- { "2", STATUS_LED_BIT2, NULL, NULL, NULL },
+#ifdef CONFIG_LED_STATUS2
+ { "2", CONFIG_LED_STATUS_BIT2, NULL, NULL, NULL },
#endif
-#ifdef STATUS_LED_BIT3
- { "3", STATUS_LED_BIT3, NULL, NULL, NULL },
+#ifdef CONFIG_LED_STATUS3
+ { "3", CONFIG_LED_STATUS_BIT3, NULL, NULL, NULL },
#endif
-#ifdef STATUS_LED_BIT4
- { "4", STATUS_LED_BIT4, NULL, NULL, NULL },
+#ifdef CONFIG_LED_STATUS4
+ { "4", CONFIG_LED_STATUS_BIT4, NULL, NULL, NULL },
#endif
-#ifdef STATUS_LED_BIT5
- { "5", STATUS_LED_BIT5, NULL, NULL, NULL },
+#ifdef CONFIG_LED_STATUS5
+ { "5", CONFIG_LED_STATUS_BIT5, NULL, NULL, NULL },
#endif
#endif
-#ifdef STATUS_LED_GREEN
- { "green", STATUS_LED_GREEN, green_led_off, green_led_on, NULL },
+#ifdef CONFIG_LED_STATUS_GREEN
+ { "green", CONFIG_LED_STATUS_GREEN, green_led_off, green_led_on, NULL },
#endif
-#ifdef STATUS_LED_YELLOW
- { "yellow", STATUS_LED_YELLOW, yellow_led_off, yellow_led_on, NULL },
+#ifdef CONFIG_LED_STATUS_YELLOW
+ { "yellow", CONFIG_LED_STATUS_YELLOW, yellow_led_off, yellow_led_on,
+ NULL },
#endif
-#ifdef STATUS_LED_RED
- { "red", STATUS_LED_RED, red_led_off, red_led_on, NULL },
+#ifdef CONFIG_LED_STATUS_RED
+ { "red", CONFIG_LED_STATUS_RED, red_led_off, red_led_on, NULL },
#endif
-#ifdef STATUS_LED_BLUE
- { "blue", STATUS_LED_BLUE, blue_led_off, blue_led_on, NULL },
+#ifdef CONFIG_LED_STATUS_BLUE
+ { "blue", CONFIG_LED_STATUS_BLUE, blue_led_off, blue_led_on, NULL },
#endif
{ NULL, 0, NULL, NULL, NULL }
};
led_commands[i].on();
else
__led_set(led_commands[i].mask,
- STATUS_LED_ON);
+ CONFIG_LED_STATUS_ON);
break;
case LED_OFF:
if (led_commands[i].off)
led_commands[i].off();
else
__led_set(led_commands[i].mask,
- STATUS_LED_OFF);
+ CONFIG_LED_STATUS_OFF);
break;
case LED_TOGGLE:
if (led_commands[i].toggle)
U_BOOT_CMD(
led, 4, 1, do_led,
"["
-#ifdef CONFIG_BOARD_SPECIFIC_LED
-#ifdef STATUS_LED_BIT
+#ifdef CONFIG_LED_STATUS_BOARD_SPECIFIC
+#ifdef CONFIG_LED_STATUS0
"0|"
#endif
-#ifdef STATUS_LED_BIT1
+#ifdef CONFIG_LED_STATUS1
"1|"
#endif
-#ifdef STATUS_LED_BIT2
+#ifdef CONFIG_LED_STATUS2
"2|"
#endif
-#ifdef STATUS_LED_BIT3
+#ifdef CONFIG_LED_STATUS3
"3|"
#endif
-#ifdef STATUS_LED_BIT4
+#ifdef CONFIG_LED_STATUS4
"4|"
#endif
-#ifdef STATUS_LED_BIT5
+#ifdef CONFIG_LED_STATUS5
"5|"
#endif
#endif
-#ifdef STATUS_LED_GREEN
+#ifdef CONFIG_LED_STATUS_GREEN
"green|"
#endif
-#ifdef STATUS_LED_YELLOW
+#ifdef CONFIG_LED_STATUS_YELLOW
"yellow|"
#endif
-#ifdef STATUS_LED_RED
+#ifdef CONFIG_LED_STATUS_RED
"red|"
#endif
-#ifdef STATUS_LED_BLUE
+#ifdef CONFIG_LED_STATUS_BLUE
"blue|"
#endif
"all] [on|off|toggle|blink] [blink-freq in ms]",
}
#endif
-#if defined(CONFIG_STATUS_LED)
+#if defined(CONFIG_LED_STATUS)
static int initr_status_led(void)
{
-#if defined(STATUS_LED_BOOT)
- status_led_set(STATUS_LED_BOOT, STATUS_LED_BLINKING);
+#if defined(CONFIG_LED_STATUS_BOOT)
+ status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_BLINKING);
#else
status_led_init();
#endif
#if defined(CONFIG_MICROBLAZE) || defined(CONFIG_AVR32) || defined(CONFIG_M68K)
timer_init, /* initialize timer */
#endif
-#if defined(CONFIG_STATUS_LED)
+#if defined(CONFIG_LED_STATUS)
initr_status_led,
#endif
/* PPC has a udelay(20) here dating from 2002. Why? */
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_EXT2=y
+CONFIG_LED_STATUS=y
+# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=1
+CONFIG_LED_STATUS_STATE=1
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
# CONFIG_PCI is not set
CONFIG_OF_LIBFDT=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_EXT2=y
+CONFIG_LED_STATUS=y
+# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=1
+CONFIG_LED_STATUS_STATE=1
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
# CONFIG_PCI is not set
CONFIG_OF_LIBFDT=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_EXT2=y
+CONFIG_LED_STATUS=y
+# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=1
+CONFIG_LED_STATUS_STATE=1
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
# CONFIG_PCI is not set
CONFIG_OF_LIBFDT=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_EXT2=y
+CONFIG_LED_STATUS=y
+# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=1
+CONFIG_LED_STATUS_STATE=1
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
# CONFIG_PCI is not set
CONFIG_OF_LIBFDT=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_EXT2=y
+CONFIG_LED_STATUS=y
+# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=1
+CONFIG_LED_STATUS_STATE=1
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
# CONFIG_PCI is not set
CONFIG_OF_LIBFDT=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_EXT2=y
+CONFIG_LED_STATUS=y
+# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=1
+CONFIG_LED_STATUS_STATE=1
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
# CONFIG_PCI is not set
CONFIG_OF_LIBFDT=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_EXT2=y
+CONFIG_LED_STATUS=y
+# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=1
+CONFIG_LED_STATUS_STATE=1
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
# CONFIG_PCI is not set
CONFIG_OF_LIBFDT=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_EXT2=y
+CONFIG_LED_STATUS=y
+# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=1
+CONFIG_LED_STATUS_STATE=1
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
# CONFIG_PCI is not set
CONFIG_OF_LIBFDT=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_EXT2=y
+CONFIG_LED_STATUS=y
+# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=1
+CONFIG_LED_STATUS_STATE=1
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
# CONFIG_PCI is not set
CONFIG_OF_LIBFDT=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_EXT2=y
+CONFIG_LED_STATUS=y
+# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=1
+CONFIG_LED_STATUS_STATE=1
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
# CONFIG_PCI is not set
CONFIG_OF_LIBFDT=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_EXT2=y
+CONFIG_LED_STATUS=y
+# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=1
+CONFIG_LED_STATUS_STATE=1
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
# CONFIG_PCI is not set
CONFIG_OF_LIBFDT=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_EXT2=y
+CONFIG_LED_STATUS=y
+# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=1
+CONFIG_LED_STATUS_STATE=1
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
# CONFIG_PCI is not set
CONFIG_OF_LIBFDT=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS_GPIO=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=37
+CONFIG_LED_STATUS_STATE=2
CONFIG_MMC_OMAP_HS=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS_GPIO=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=64
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_OF_LIBFDT=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS_GPIO=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=186
+CONFIG_LED_STATUS_STATE=2
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS_GPIO=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=186
+CONFIG_LED_STATUS_STATE=2
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=8
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
+CONFIG_LED_STATUS_CMD=y
# CONFIG_CFB_CONSOLE is not set
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=8
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
+CONFIG_LED_STATUS_CMD=y
# CONFIG_CFB_CONSOLE is not set
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_FAT=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=0
+CONFIG_LED_STATUS_STATE=2
+CONFIG_LED_STATUS1=y
+CONFIG_LED_STATUS_BIT1=1
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
+CONFIG_LED_STATUS_RED_ENABLE=y
+CONFIG_LED_STATUS_RED=1
+CONFIG_LED_STATUS_GREEN_ENABLE=y
+CONFIG_LED_STATUS_GREEN=0
CONFIG_USB=y
CONFIG_USB_STORAGE=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_CMD_UBI=y
CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS_GPIO=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=27
+CONFIG_LED_STATUS_STATE=2
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_OF_LIBFDT=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_UBI=y
CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS_GPIO=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=16
+CONFIG_LED_STATUS_STATE=2
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_OF_LIBFDT=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=0
+CONFIG_LED_STATUS_STATE=1
+CONFIG_LED_STATUS_FREQ=10
+CONFIG_LED_STATUS1=y
+CONFIG_LED_STATUS_BIT1=1
+CONFIG_LED_STATUS_FREQ1=10
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
# CONFIG_PCI is not set
CONFIG_OF_LIBFDT=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS_GPIO=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=59
+CONFIG_LED_STATUS_STATE=2
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
+CONFIG_LED_STATUS_CMD=y
CONFIG_MMC_MXS=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_EXT4_WRITE=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=1
+CONFIG_LED_STATUS_STATE=2
+CONFIG_LED_STATUS1=y
+CONFIG_LED_STATUS_BIT1=2
+CONFIG_LED_STATUS_STATE1=2
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=1
+CONFIG_LED_STATUS_GREEN_ENABLE=y
+CONFIG_LED_STATUS_GREEN=2
+CONFIG_LED_STATUS_CMD=y
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_DFU_SF=y
CONFIG_DM_GPIO=y
CONFIG_DWAPB_GPIO=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS_GPIO=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=48
+CONFIG_LED_STATUS1=y
+CONFIG_LED_STATUS_BIT1=53
+CONFIG_LED_STATUS2=y
+CONFIG_LED_STATUS_BIT2=54
+CONFIG_LED_STATUS3=y
+CONFIG_LED_STATUS_BIT3=65
+CONFIG_LED_STATUS_CMD=y
CONFIG_DM_MMC=y
CONFIG_MMC_DW=y
CONFIG_SPI_FLASH=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=0
+CONFIG_LED_STATUS_STATE=2
+CONFIG_LED_STATUS1=y
+CONFIG_LED_STATUS_BIT1=1
+CONFIG_LED_STATUS_STATE1=2
+CONFIG_LED_STATUS2=y
+CONFIG_LED_STATUS_BIT2=2
+CONFIG_LED_STATUS_STATE2=2
+CONFIG_LED_STATUS3=y
+CONFIG_LED_STATUS_BIT3=3
+CONFIG_LED_STATUS_STATE3=2
+CONFIG_LED_STATUS4=y
+CONFIG_LED_STATUS_BIT4=4
+CONFIG_LED_STATUS_STATE4=2
+CONFIG_LED_STATUS5=y
+CONFIG_LED_STATUS_BIT5=5
+CONFIG_LED_STATUS_STATE5=2
+CONFIG_LED_STATUS_CMD=y
CONFIG_PCA9551_LED=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_UBI=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=1
+CONFIG_LED_STATUS_STATE=2
+CONFIG_LED_STATUS1=y
+CONFIG_LED_STATUS_BIT1=2
+CONFIG_LED_STATUS_STATE1=2
+CONFIG_LED_STATUS2=y
+CONFIG_LED_STATUS_BIT2=4
+CONFIG_LED_STATUS_STATE2=2
+CONFIG_LED_STATUS_CMD=y
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_OF_LIBFDT=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_UBI=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=1
+CONFIG_LED_STATUS_STATE=2
+CONFIG_LED_STATUS1=y
+CONFIG_LED_STATUS_BIT1=2
+CONFIG_LED_STATUS_STATE1=2
+CONFIG_LED_STATUS2=y
+CONFIG_LED_STATUS_BIT2=4
+CONFIG_LED_STATUS_STATE2=2
+CONFIG_LED_STATUS_CMD=y
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_OF_LIBFDT=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_LED_STATUS=y
+CONFIG_LED_STATUS0=y
+CONFIG_LED_STATUS_BIT=16
+CONFIG_LED_STATUS_STATE=1
+CONFIG_LED_STATUS_BOOT_ENABLE=y
+CONFIG_LED_STATUS_BOOT=0
# CONFIG_PCI is not set
CONFIG_USB=y
CONFIG_USB_STORAGE=y
obj-$(CONFIG_CROS_EC_SPI) += cros_ec_spi.o
endif
obj-$(CONFIG_FSL_IIM) += fsl_iim.o
-obj-$(CONFIG_GPIO_LED) += gpio_led.o
+obj-$(CONFIG_LED_STATUS_GPIO) += gpio_led.o
obj-$(CONFIG_I2C_EEPROM) += i2c_eeprom.o
obj-$(CONFIG_FSL_MC9SDZ60) += mc9sdz60.o
obj-$(CONFIG_MXC_OCOTP) += mxc_ocotp.o
endif
obj-$(CONFIG_SMSC_LPC47M) += smsc_lpc47m.o
obj-$(CONFIG_SMSC_SIO1007) += smsc_sio1007.o
-obj-$(CONFIG_STATUS_LED) += status_led.o
+obj-$(CONFIG_LED_STATUS) += status_led.o
obj-$(CONFIG_SANDBOX) += swap_case.o
ifdef CONFIG_SPL_OF_PLATDATA
ifdef CONFIG_SPL_BUILD
static int gpio_led_gpio_value(led_id_t mask, int state)
{
- int i, gpio_value = (state == STATUS_LED_ON);
+ int i, gpio_value = (state == CONFIG_LED_STATUS_ON);
for (i = 0; i < ARRAY_SIZE(gpio_led_inv); i++) {
if (gpio_led_inv[i] == mask)
/* 'generic' override of colored LED stubs, to use GPIO functions instead */
-#ifdef STATUS_LED_RED
+#ifdef CONFIG_LED_STATUS_RED
void red_led_on(void)
{
- __led_set(STATUS_LED_RED, STATUS_LED_ON);
+ __led_set(CONFIG_LED_STATUS_RED, CONFIG_LED_STATUS_ON);
}
void red_led_off(void)
{
- __led_set(STATUS_LED_RED, STATUS_LED_OFF);
+ __led_set(CONFIG_LED_STATUS_RED, CONFIG_LED_STATUS_OFF);
}
#endif
-#ifdef STATUS_LED_GREEN
+#ifdef CONFIG_LED_STATUS_GREEN
void green_led_on(void)
{
- __led_set(STATUS_LED_GREEN, STATUS_LED_ON);
+ __led_set(CONFIG_LED_STATUS_GREEN, CONFIG_LED_STATUS_ON);
}
void green_led_off(void)
{
- __led_set(STATUS_LED_GREEN, STATUS_LED_OFF);
+ __led_set(CONFIG_LED_STATUS_GREEN, CONFIG_LED_STATUS_OFF);
}
#endif
-#ifdef STATUS_LED_YELLOW
+#ifdef CONFIG_LED_STATUS_YELLOW
void yellow_led_on(void)
{
- __led_set(STATUS_LED_YELLOW, STATUS_LED_ON);
+ __led_set(CONFIG_LED_STATUS_YELLOW, CONFIG_LED_STATUS_ON);
}
void yellow_led_off(void)
{
- __led_set(STATUS_LED_YELLOW, STATUS_LED_OFF);
+ __led_set(CONFIG_LED_STATUS_YELLOW, CONFIG_LED_STATUS_OFF);
}
#endif
-#ifdef STATUS_LED_BLUE
+#ifdef CONFIG_LED_STATUS_BLUE
void blue_led_on(void)
{
- __led_set(STATUS_LED_BLUE, STATUS_LED_ON);
+ __led_set(CONFIG_LED_STATUS_BLUE, CONFIG_LED_STATUS_ON);
}
void blue_led_off(void)
{
- __led_set(STATUS_LED_BLUE, STATUS_LED_OFF);
+ __led_set(CONFIG_LED_STATUS_BLUE, CONFIG_LED_STATUS_OFF);
}
#endif
void __led_set(led_id_t mask, int state)
{
- if (state == STATUS_LED_OFF)
+ if (state == CONFIG_LED_STATUS_OFF)
pca9551_led_set_state(mask, PCA9551_LED_STATE_OFF);
else
pca9551_led_set_state(mask, PCA9551_LED_STATE_ON);
} led_dev_t;
led_dev_t led_dev[] = {
- { STATUS_LED_BIT,
- STATUS_LED_STATE,
- STATUS_LED_PERIOD,
- 0,
- },
-#if defined(STATUS_LED_BIT1)
- { STATUS_LED_BIT1,
- STATUS_LED_STATE1,
- STATUS_LED_PERIOD1,
- 0,
- },
+ { CONFIG_LED_STATUS_BIT,
+ CONFIG_LED_STATUS_STATE,
+ LED_STATUS_PERIOD,
+ 0,
+ },
+#if defined(CONFIG_LED_STATUS1)
+ { CONFIG_LED_STATUS_BIT1,
+ CONFIG_LED_STATUS_STATE1,
+ LED_STATUS_PERIOD1,
+ 0,
+ },
#endif
-#if defined(STATUS_LED_BIT2)
- { STATUS_LED_BIT2,
- STATUS_LED_STATE2,
- STATUS_LED_PERIOD2,
- 0,
- },
+#if defined(CONFIG_LED_STATUS2)
+ { CONFIG_LED_STATUS_BIT2,
+ CONFIG_LED_STATUS_STATE2,
+ LED_STATUS_PERIOD2,
+ 0,
+ },
#endif
-#if defined(STATUS_LED_BIT3)
- { STATUS_LED_BIT3,
- STATUS_LED_STATE3,
- STATUS_LED_PERIOD3,
- 0,
- },
+#if defined(CONFIG_LED_STATUS3)
+ { CONFIG_LED_STATUS_BIT3,
+ CONFIG_LED_STATUS_STATE3,
+ LED_STATUS_PERIOD3,
+ 0,
+ },
#endif
-#if defined(STATUS_LED_BIT4)
- { STATUS_LED_BIT4,
- STATUS_LED_STATE4,
- STATUS_LED_PERIOD4,
- 0,
- },
+#if defined(CONFIG_LED_STATUS4)
+ { CONFIG_LED_STATUS_BIT4,
+ CONFIG_LED_STATUS_STATE4,
+ LED_STATUS_PERIOD4,
+ 0,
+ },
#endif
-#if defined(STATUS_LED_BIT5)
- { STATUS_LED_BIT5,
- STATUS_LED_STATE5,
- STATUS_LED_PERIOD5,
- 0,
- },
+#if defined(CONFIG_LED_STATUS5)
+ { CONFIG_LED_STATUS_BIT5,
+ CONFIG_LED_STATUS_STATE5,
+ LED_STATUS_PERIOD5,
+ 0,
+ },
#endif
};
for (i = 0, ld = led_dev; i < MAX_LED_DEV; i++, ld++) {
- if (ld->state != STATUS_LED_BLINKING)
+ if (ld->state != CONFIG_LED_STATUS_BLINKING)
continue;
if (++ld->cnt >= ld->period) {
ld = &led_dev[led];
ld->state = state;
- if (state == STATUS_LED_BLINKING) {
+ if (state == CONFIG_LED_STATUS_BLINKING) {
ld->cnt = 0; /* always start with full period */
- state = STATUS_LED_ON; /* always start with LED _ON_ */
+ state = CONFIG_LED_STATUS_ON; /* always start with LED _ON_ */
}
__led_set (ld->mask, state);
}
int pcmcia_init (void);
-#ifdef CONFIG_STATUS_LED
+#ifdef CONFIG_LED_STATUS
# include <status_led.h>
#endif
#define CONFIG_WATCHDOG /* turn on platform specific watchdog */
-/*#define CONFIG_STATUS_LED 1 */ /* Enable status led */
-
#define CONFIG_LOADS_ECHO 1 /* Echo on for serial download */
/*
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#if defined(CONFIG_LCD)
-# undef CONFIG_STATUS_LED /* disturbs display */
-#else
-# define CONFIG_STATUS_LED 1 /* Status LED enabled */
-#endif /* CONFIG_LCD */
-
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
/*
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#ifdef CONFIG_LCD
-# undef CONFIG_STATUS_LED /* disturbs display */
-#else
-# define CONFIG_STATUS_LED 1 /* Status LED enabled */
-#endif /* CONFIG_LCD */
-
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
/*
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
/*
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
/*
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
/*
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
/* enable I2C and select the hardware/software driver */
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
/*
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
/*
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
/*
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
/*
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
/* enable I2C and select the hardware/software driver */
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
/* enable I2C and select the hardware/software driver */
#define CONFIG_UART_CONSOLE 1
/* define to enable run status via led */
-/* #define CONFIG_STATUS_LED */
-#ifdef CONFIG_STATUS_LED
-#define CONFIG_GPIO_LED
-#define CONFIG_BOARD_SPECIFIC_LED
-/* use LED0 to indicate booting/alive */
-#define STATUS_LED_BOOT 0
-#define STATUS_LED_BIT GPIO_PF8
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4)
-/* use LED1 to indicate crash */
-#define STATUS_LED_CRASH 1
-#define STATUS_LED_BIT1 GPIO_PG11
-#define STATUS_LED_STATE1 STATUS_LED_ON
-#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
-/* #define STATUS_LED_BIT2 GPIO_PG12 */
-#endif
/*
* Pull in common ADI header for remaining command/environment setup
/* #define CONFIG_SHOW_BOOT_PROGRESS */
/* define to enable run status via led */
-/* #define CONFIG_STATUS_LED */
-#ifdef CONFIG_STATUS_LED
-#define CONFIG_GPIO_LED
-#define CONFIG_BOARD_SPECIFIC_LED
-/* use LED0 to indicate booting/alive */
-#define STATUS_LED_BOOT 0
-#define STATUS_LED_BIT GPIO_PF2
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4)
-/* use LED1 to indicate crash */
-#define STATUS_LED_CRASH 1
-#define STATUS_LED_BIT1 GPIO_PF3
-#define STATUS_LED_STATE1 STATUS_LED_ON
-#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
-/* #define STATUS_LED_BIT2 GPIO_PF4 */
-#endif
/* define to enable splash screen support */
#define CONFIG_MISC_INIT_R
#define CONFIG_REVISION_TAG
-/* Status LED */
-#define CONFIG_STATUS_LED /* Status LED enabled */
-#define CONFIG_GPIO_LED
-#define CONFIG_BOARD_SPECIFIC_LED
-#define GREEN_LED_DEV 0
- /* cl_som_am57x Green LED is GPIO2_5 */
-#define GREEN_LED_GPIO 37
-#define STATUS_LED_BIT GREEN_LED_GPIO
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-
/* PMIC I2C bus number */
#define CONFIG_SYS_SPD_BUS_NUM 3
#define GPIO_PIN(_bank, _pin) ((_bank << 5) + _pin)
/* Status LED */
-#define CONFIG_STATUS_LED
-#define CONFIG_GPIO_LED
-#define CONFIG_BOARD_SPECIFIC_LED
-#define STATUS_LED_BIT GPIO_PIN(2, 0)
/* Status LED polarity is inversed, so init it in the "off" state */
-#define STATUS_LED_STATE STATUS_LED_OFF
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BOOT 0
/* EEPROM */
#define CONFIG_CMD_EEPROM
GENERATED_GBL_DATA_SIZE)
/* Status LED */
-#define CONFIG_STATUS_LED /* Status LED enabled */
-#define CONFIG_BOARD_SPECIFIC_LED
-#define CONFIG_GPIO_LED
#define GREEN_LED_GPIO 186 /* CM-T35 Green LED is GPIO186 */
-#define GREEN_LED_DEV 0
-#define STATUS_LED_BIT GREEN_LED_GPIO
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BOOT GREEN_LED_DEV
#define CONFIG_SPLASHIMAGE_GUARD
/* GPIO banks */
-#ifdef CONFIG_STATUS_LED
+#ifdef CONFIG_LED_STATUS
#define CONFIG_OMAP3_GPIO_6 /* GPIO186 is in GPIO bank 6 */
#endif
GENERATED_GBL_DATA_SIZE)
/* Status LED */
-#define CONFIG_STATUS_LED /* Status LED enabled */
-#define CONFIG_BOARD_SPECIFIC_LED
-#define CONFIG_GPIO_LED
#define GREEN_LED_GPIO 186 /* CM-T3517 Green LED is GPIO186 */
-#define GREEN_LED_DEV 0
-#define STATUS_LED_BIT GREEN_LED_GPIO
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BOOT GREEN_LED_DEV
/* GPIO banks */
-#ifdef CONFIG_STATUS_LED
+#ifdef CONFIG_LED_STATUS
#define CONFIG_OMAP3_GPIO_6 /* GPIO186 is in GPIO bank 6 */
#endif
#define CONFIG_HW_WATCHDOG
-#define CONFIG_STATUS_LED
-#define CONFIG_BOARD_SPECIFIC_LED
#define STATUS_LED_ACTIVE 0
-#define STATUS_LED_BIT 0x0008 /* Timer7 GPIO */
-#define STATUS_LED_BOOT 0
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_STATE STATUS_LED_OFF
/*----------------------------------------------------------------------*
* Configuration for environment *
*/
#define CONFIG_CMDLINE_EDITING
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_LED
#define CONFIG_MCFTMR
#define CONFIG_PL01x_PORTS {(void *)CONFIG_SYS_SERIAL0}
/* Status LED */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-#define CONFIG_BOARD_SPECIFIC_LED 1
-#define STATUS_LED_GREEN 0
-#define STATUS_LED_RED 1
-/* Green */
-#define STATUS_LED_BIT STATUS_LED_GREEN
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-/* Red */
-#define STATUS_LED_BIT1 STATUS_LED_RED
-#define STATUS_LED_STATE1 STATUS_LED_OFF
-#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
/* Optional value */
-#define STATUS_LED_BOOT STATUS_LED_BIT
/* Network hardware configuration */
#define CONFIG_DRIVER_EP93XX_MAC
/*
* Status LED configuration
*/
-#define CONFIG_STATUS_LED /* Status LED enabled */
-#define CONFIG_BOARD_SPECIFIC_LED
#define ENABLE_GPIO_OUT 0x00000024
#define LED_ON 0x00000010
-#ifndef __ASSEMBLY__
-/*
- * In case of Motion-PRO, a LED is identified by its corresponding
- * GPT Enable and Mode Select Register.
- */
-typedef volatile unsigned long * led_id_t;
-
-extern void __led_init(led_id_t id, int state);
-extern void __led_toggle(led_id_t id);
-extern void __led_set(led_id_t id, int state);
-#endif /* __ASSEMBLY__ */
-
/*
* Temperature sensor
*/
#define CONFIG_SYS_NO_FLASH
#define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_LED
-
/* Memory configuration */
#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */
#define PHYS_SDRAM_1 0x40000000 /* Base address */
#endif
/* Status LED */
-#define CONFIG_STATUS_LED
-#define CONFIG_GPIO_LED
-#define CONFIG_BOARD_SPECIFIC_LED
-#define STATUS_LED_BOOT 0
-#define STATUS_LED_BIT MX23_PAD_SSP1_DETECT__GPIO_2_1
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
/* USB */
#ifdef CONFIG_CMD_USB
#define CONFIG_ENV_OVERWRITE
/* Status LED */
-#define CONFIG_STATUS_LED 1
-#define CONFIG_BOARD_SPECIFIC_LED 1
-#define STATUS_LED_BIT 0x01
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT1 0x02
-#define STATUS_LED_STATE1 STATUS_LED_ON
-#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BOOT STATUS_LED_BIT
-#define STATUS_LED_GREEN STATUS_LED_BIT1
/* Enable Multi Bus support for I2C */
#define CONFIG_I2C_MULTI_BUS 1
"4m(kernel),-(fs)"
#define CONFIG_CMD_NAND /* NAND support */
-#define CONFIG_CMD_LED /* LED support */
#define CONFIG_VIDEO_OMAP3 /* DSS Support */
/* Status LED available for IGEP0020 and IGEP0030 but not IGEP0032 */
#if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0020) || \
(CONFIG_MACH_TYPE == MACH_TYPE_IGEP0030)
-#define CONFIG_STATUS_LED
-#define CONFIG_BOARD_SPECIFIC_LED
-#define CONFIG_GPIO_LED
#if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0020)
#define RED_LED_GPIO 27
#elif (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0030)
#define RED_LED_GPIO 16
#endif
-#define RED_LED_DEV 0
-#define STATUS_LED_BIT RED_LED_GPIO
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BOOT RED_LED_DEV
#endif
/* GPIO banks */
#define CONFIG_HW_WATCHDOG
#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_LED
/* Memory configurations */
#define PHYS_SDRAM_1_SIZE 0x40000000 /* 1GiB on VINING_FPGA */
* 2 ... Bottom Green
* 3 ... Bottom Red
*/
-#define CONFIG_STATUS_LED
-#define CONFIG_GPIO_LED
-#define CONFIG_BOARD_SPECIFIC_LED
-#define STATUS_LED_BIT 48
-#define STATUS_LED_STATE STATUS_LED_OFF
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT1 53
-#define STATUS_LED_STATE1 STATUS_LED_OFF
-#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT2 54
-#define STATUS_LED_STATE2 STATUS_LED_OFF
-#define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT3 65
-#define STATUS_LED_STATE3 STATUS_LED_OFF
-#define STATUS_LED_PERIOD3 (CONFIG_SYS_HZ / 2)
/* Ethernet on SoC (EMAC) */
#if defined(CONFIG_CMD_NET)
#define CONFIG_ENV_SECT_SIZE (128 << 10)
#define CONFIG_ENV_SIZE (8 << 10)
-#define CONFIG_BOARD_SPECIFIC_LED
#define CONFIG_RED_LED 110
#define CONFIG_GREEN_LED 109
#define CONFIG_CMD_DATE
/* LED */
-#define CONFIG_CMD_LED
-#define CONFIG_STATUS_LED
-#define CONFIG_BOARD_SPECIFIC_LED
-#define STATUS_LED_BIT 0
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT1 1
-#define STATUS_LED_STATE1 STATUS_LED_ON
-#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT2 2
-#define STATUS_LED_STATE2 STATUS_LED_ON
-#define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT3 3
-#define STATUS_LED_STATE3 STATUS_LED_ON
-#define STATUS_LED_PERIOD3 (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT4 4
-#define STATUS_LED_STATE4 STATUS_LED_ON
-#define STATUS_LED_PERIOD4 (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT5 5
-#define STATUS_LED_STATE5 STATUS_LED_ON
-#define STATUS_LED_PERIOD5 (CONFIG_SYS_HZ / 2)
/* Bootcounter */
#define CONFIG_BOOTCOUNT_LIMIT
#define CONFIG_OMAP3_GPIO_2 /* GPIO32..63 are in GPIO bank 2 */
/* LED support */
-#define CONFIG_STATUS_LED
-#define CONFIG_BOARD_SPECIFIC_LED
-#define CONFIG_CMD_LED /* LED command */
-#define STATUS_LED_BIT (1 << 0)
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT1 (1 << 1)
-#define STATUS_LED_STATE1 STATUS_LED_ON
-#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BIT2 (1 << 2)
-#define STATUS_LED_STATE2 STATUS_LED_ON
-#define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 2)
/* NS16550 Configuration */
#define CONFIG_SYS_NS16550_SERIAL
/*
* Status LED
*/
-#define CONFIG_STATUS_LED /* Status LED enabled */
-#define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */
#define CONFIG_SYS_LED_BASE MPC5XXX_GPT7_ENABLE /* Timer 7 GPIO */
#ifndef __ASSEMBLY__
#ifndef _STATUS_LED_H_
#define _STATUS_LED_H_
-#ifdef CONFIG_STATUS_LED
-
-#define STATUS_LED_OFF 0
-#define STATUS_LED_BLINKING 1
-#define STATUS_LED_ON 2
+#ifdef CONFIG_LED_STATUS
+
+#define LED_STATUS_PERIOD (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ)
+#ifdef CONFIG_LED_STATUS1
+#define LED_STATUS_PERIOD1 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ1)
+#endif /* CONFIG_LED_STATUS1 */
+#ifdef CONFIG_LED_STATUS2
+#define LED_STATUS_PERIOD2 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ2)
+#endif /* CONFIG_LED_STATUS2 */
+#ifdef CONFIG_LED_STATUS3
+#define LED_STATUS_PERIOD3 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ3)
+#endif /* CONFIG_LED_STATUS3 */
+#ifdef CONFIG_LED_STATUS4
+#define LED_STATUS_PERIOD4 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ4)
+#endif /* CONFIG_LED_STATUS4 */
+#ifdef CONFIG_LED_STATUS5
+#define LED_STATUS_PERIOD5 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ5)
+#endif /* CONFIG_LED_STATUS5 */
void status_led_init(void);
void status_led_tick (unsigned long timestamp);
# define STATUS_LED_ODR im_cpm.cp_pbodr
# define STATUS_LED_DAT im_cpm.cp_pbdat
-# define STATUS_LED_BIT 0x00000001
-# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-# define STATUS_LED_STATE STATUS_LED_BLINKING
-
# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
-# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
-
/***** MVS v1 **********************************************************/
#elif (defined(CONFIG_MVS) && CONFIG_MVS < 2)
# define STATUS_LED_PAR im_ioport.iop_pdpar
# undef STATUS_LED_ODR
# define STATUS_LED_DAT im_ioport.iop_pddat
-# define STATUS_LED_BIT 0x00000001
-# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-# define STATUS_LED_STATE STATUS_LED_BLINKING
-
# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
-# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
-
/***** Someone else defines these *************************************/
#elif defined(STATUS_LED_PAR)
-
/*
* ADVICE: Define in your board configuration file rather than
* filling this file up with lots of custom board stuff.
#elif defined(CONFIG_V38B)
-# define STATUS_LED_BIT 0x0010 /* Timer7 GPIO */
-# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-# define STATUS_LED_STATE STATUS_LED_BLINKING
-
# define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */
-# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
-
-#elif defined(CONFIG_MOTIONPRO)
-
-#define STATUS_LED_BIT ((vu_long *) MPC5XXX_GPT6_ENABLE)
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 10)
-#define STATUS_LED_STATE STATUS_LED_BLINKING
-
-#define STATUS_LED_BIT1 ((vu_long *) MPC5XXX_GPT7_ENABLE)
-#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 10)
-#define STATUS_LED_STATE1 STATUS_LED_OFF
-
-#define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
-#elif defined(CONFIG_BOARD_SPECIFIC_LED)
+#elif defined(CONFIG_LED_STATUS_BOARD_SPECIFIC)
/* led_id_t is unsigned long mask */
typedef unsigned long led_id_t;
#endif
/************************************************************************/
-#ifndef CONFIG_BOARD_SPECIFIC_LED
+#ifndef CONFIG_LED_STATUS_BOARD_SPECIFIC
# include <asm/status_led.h>
#endif
-#endif /* CONFIG_STATUS_LED */
+#endif /* CONFIG_LED_STATUS */
/*
* Coloured LEDs API
#include <net/tftp.h>
#include "bootp.h"
#include "nfs.h"
-#ifdef CONFIG_STATUS_LED
+#ifdef CONFIG_LED_STATUS
#include <status_led.h>
#endif
#ifdef CONFIG_BOOTP_RANDOM_DELAY
/*
* Got a good BOOTP reply. Copy the data into our variables.
*/
-#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
- status_led_set(STATUS_LED_BOOT, STATUS_LED_OFF);
+#if defined(CONFIG_LED_STATUS) && defined(CONFIG_LED_STATUS_BOOT_ENABLE)
+ status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_OFF);
#endif
store_net_params(bp); /* Store net parameters from reply */
#include <errno.h>
#include <net.h>
#include <net/tftp.h>
-#if defined(CONFIG_STATUS_LED)
+#if defined(CONFIG_LED_STATUS)
#include <miiphy.h>
#include <status_led.h>
#endif
#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
#if defined(CONFIG_SYS_FAULT_ECHO_LINK_DOWN) && \
- defined(CONFIG_STATUS_LED) && \
- defined(STATUS_LED_RED)
+ defined(CONFIG_LED_STATUS) && \
+ defined(CONFIG_LED_STATUS_RED)
/*
* Echo the inverted link state to the fault LED.
*/
if (miiphy_link(eth_get_dev()->name, CONFIG_SYS_FAULT_MII_ADDR))
- status_led_set(STATUS_LED_RED, STATUS_LED_OFF);
+ status_led_set(CONFIG_LED_STATUS_RED, CONFIG_LED_STATUS_OFF);
else
- status_led_set(STATUS_LED_RED, STATUS_LED_ON);
+ status_led_set(CONFIG_LED_STATUS_RED, CONFIG_LED_STATUS_ON);
#endif /* CONFIG_SYS_FAULT_ECHO_LINK_DOWN, ... */
#endif /* CONFIG_MII, ... */
#ifdef CONFIG_USB_KEYBOARD
#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
#if defined(CONFIG_SYS_FAULT_ECHO_LINK_DOWN) && \
- defined(CONFIG_STATUS_LED) && \
- defined(STATUS_LED_RED)
+ defined(CONFIG_LED_STATUS) && \
+ defined(CONFIG_LED_STATUS_RED)
/*
* Echo the inverted link state to the fault LED.
*/
if (miiphy_link(eth_get_dev()->name,
CONFIG_SYS_FAULT_MII_ADDR))
- status_led_set(STATUS_LED_RED, STATUS_LED_OFF);
+ status_led_set(CONFIG_LED_STATUS_RED,
+ CONFIG_LED_STATUS_OFF);
else
- status_led_set(STATUS_LED_RED, STATUS_LED_ON);
+ status_led_set(CONFIG_LED_STATUS_RED,
+ CONFIG_LED_STATUS_ON);
#endif /* CONFIG_SYS_FAULT_ECHO_LINK_DOWN, ... */
#endif /* CONFIG_MII, ... */
debug_cond(DEBUG_INT_STATE, "--- net_loop timeout\n");
CONFIG_BOARD_RESET
CONFIG_BOARD_REVISION_TAG
CONFIG_BOARD_SIZE_LIMIT
-CONFIG_BOARD_SPECIFIC_LED
CONFIG_BOARD_TAURUS
CONFIG_BOARD_TYPES
CONFIG_BOOGER
CONFIG_CMD_JFFS2
CONFIG_CMD_KGDB
CONFIG_CMD_LDRINFO
-CONFIG_CMD_LED
CONFIG_CMD_LOADY
CONFIG_CMD_LZMADEC
CONFIG_CMD_MAX6957
CONFIG_GPCS_PHY_ADDR
CONFIG_GPIO
CONFIG_GPIO_ENABLE_SPI_FLASH
-CONFIG_GPIO_LED
CONFIG_GPIO_LED_INVERTED_TABLE
CONFIG_GPIO_LED_STUBS
CONFIG_GREEN_LED
CONFIG_STANDALONE_LOAD_ADDR
CONFIG_STATIC_BOARD_REV
CONFIG_STATIC_RELA
-CONFIG_STATUS_LED
CONFIG_STD_DEVICES_SETTINGS
CONFIG_STK52XX
CONFIG_STK52XX_REV100
projects / u-boot / commitdiff