This option has a bool type, not hex.
Fix it and enable it if CONFIG_DM is on because Driver Model always
requires malloc memory. Devices are scanned twice, before/after
relocation. CONFIG_SYS_MALLOC_F should be enabled to use malloc
memory before relocation. As it is board-independent, handle it
globally.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>
config SYS_MALLOC_F
bool "Enable malloc() pool before relocation"
- default 0x400
+ default y if DM
help
Before relocation memory is very limited on many platforms. Still,
we can provide a small malloc() pool if needed. Driver model in
config DM_GPIO
default y
-config SYS_MALLOC_F
- default y
-
source "board/samsung/smdkv310/Kconfig"
source "board/samsung/trats/Kconfig"
source "board/samsung/universal_c210/Kconfig"
config DM_SERIAL
default y if DM
-config SYS_MALLOC_F
- default y if DM
-
config SYS_SOC
default "omap3"
endchoice
-config SYS_MALLOC_F
- default y
-
config SYS_MALLOC_F_LEN
default 0x1800
endchoice
-config SYS_MALLOC_F
- default y
-
config CMD_PINMON
bool "Enable boot mode pins monitor command"
default y
config DM_SERIAL
default y
-config SYS_MALLOC_F
- default y
-
config SYS_MALLOC_F_LEN
default 0x800
config DM_SERIAL
default y
-config SYS_MALLOC_F
- bool
- default y
-
endif
config DM_SERIAL
default y if DM
-config SYS_MALLOC_F
- default y if DM
-
endif
CONFIG_DRAM_CLK=480
CONFIG_DRAM_ZQ=122
CONFIG_DRAM_EMR1=4
-CONFIG_SYS_MALLOC_F=y
CONFIG_SPL_STACK_R_ADDR=0x82000000
CONFIG_ARM=y
CONFIG_TARGET_AM335X_IGEP0033=y
-CONFIG_SYS_MALLOC_F=y
CONFIG_DM=y
CONFIG_DM_GPIO=y
CONFIG_DM_SERIAL=y
-CONFIG_SYS_MALLOC_F=y
CONFIG_SPL=y
CONFIG_ARM=y
CONFIG_TARGET_CM_T335=y
-CONFIG_SYS_MALLOC_F=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qsabreauto/mx6dl.cfg,MX6DL"
CONFIG_ARM=y
CONFIG_TARGET_MX6QSABREAUTO=y
-CONFIG_SYS_MALLOC_F=y
CONFIG_DM=y
CONFIG_DM_THERMAL=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qsabreauto/imximage.cfg,MX6Q"
CONFIG_ARM=y
CONFIG_TARGET_MX6QSABREAUTO=y
-CONFIG_SYS_MALLOC_F=y
CONFIG_DM=y
CONFIG_DM_THERMAL=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg,MX6Q"
CONFIG_ARM=y
CONFIG_TARGET_MX6SABRESD=y
-CONFIG_SYS_MALLOC_F=y
CONFIG_DM=y
CONFIG_DM_THERMAL=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6sxsabresd/imximage.cfg,MX6SX"
CONFIG_ARM=y
CONFIG_TARGET_MX6SXSABRESD=y
-CONFIG_SYS_MALLOC_F=y
CONFIG_DM=y
CONFIG_DM_THERMAL=y
CONFIG_DM=n
CONFIG_DM_SERIAL=n
CONFIG_DM_GPIO=n
-CONFIG_SYS_MALLOC_F=y
CONFIG_SYS_EXTRA_OPTIONS="REV1"
CONFIG_ARM=y
CONFIG_TARGET_PCM051=y
-CONFIG_SYS_MALLOC_F=y
CONFIG_SYS_EXTRA_OPTIONS="REV3"
CONFIG_ARM=y
CONFIG_TARGET_PCM051=y
-CONFIG_SYS_MALLOC_F=y
CONFIG_SPL=y
CONFIG_ARM=y
CONFIG_TARGET_PENGWYN=y
-CONFIG_SYS_MALLOC_F=y
CONFIG_SPL=y
CONFIG_ARM=y
CONFIG_TARGET_PEPPER=y
-CONFIG_SYS_MALLOC_F=y
CONFIG_ARM=y
CONFIG_TARGET_RPI_2=y
-CONFIG_SYS_MALLOC_F=y
CONFIG_ARM=y
CONFIG_TARGET_RPI=y
-CONFIG_SYS_MALLOC_F=y
CONFIG_ARCH_S5PC1XX=y
CONFIG_TARGET_S5P_GONI=y
CONFIG_DEFAULT_DEVICE_TREE="s5pc1xx-goni"
-CONFIG_SYS_MALLOC_F=y
CONFIG_FIT_SIGNATURE=y
CONFIG_DM=y
CONFIG_DEFAULT_DEVICE_TREE="sandbox"
-CONFIG_SYS_MALLOC_F=y
CONFIG_CROS_EC=y
CONFIG_DM_CROS_EC=y
CONFIG_CROS_EC_SANDBOX=y
CONFIG_TARGET_SMDKC100=y
CONFIG_ARCH_S5PC1XX=y
CONFIG_DEFAULT_DEVICE_TREE="s5pc1xx-smdkc100"
-CONFIG_SYS_MALLOC_F=y
CONFIG_DM=y
CONFIG_DM_GPIO=y
CONFIG_DM_SERIAL=y
-CONFIG_SYS_MALLOC_F=y
CONFIG_DM=y
CONFIG_DM_GPIO=y
CONFIG_DM_SERIAL=y
-CONFIG_SYS_MALLOC_F=y
CONFIG_SYS_EXTRA_OPTIONS="stv0991"
CONFIG_ARM=y
CONFIG_TARGET_STV0991=y
-CONFIG_SYS_MALLOC_F=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_DM=y
CONFIG_DM_SERIAL=y
#define CONFIG_SYS_THUMB_BUILD
#define CONFIG_SYS_GENERIC_BOARD
-#define CONFIG_SYS_MALLOC_F_LEN (1 << 10)
-
/* Support File sytems */
#define CONFIG_FAT_WRITE
#define CONFIG_DOS_PARTITION