]> git.sur5r.net Git - u-boot/commitdiff
ARMV7: OMAP3: Remove erroneous hard coded sdram setup for 128MB/bank
authorSteve Sakoman <steve@sakoman.com>
Fri, 20 Aug 2010 03:09:57 +0000 (20:09 -0700)
committerSandeep Paulraj <s-paulraj@ti.com>
Wed, 8 Sep 2010 18:51:24 +0000 (14:51 -0400)
Upcoming Beagle and Overo revisions use POP memory with 256MB or 512MB
per bank.  This patches uses the SDRC settings from x-load or the config
header to set up timing properly.

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
arch/arm/cpu/armv7/omap3/sdrc.c

index 96fd990c71c44c622f1177311b014e9e61d076fe..8905224439b5e7d07204c2b5b2b4f180c5599ce8 100644 (file)
@@ -107,18 +107,12 @@ u32 get_sdr_cs_offset(u32 cs)
 /*
  * do_sdrc_init -
  *  - Initialize the SDRAM for use.
- *  - Sets up SDRC timings for CS0
  *  - code called once in C-Stack only context for CS0 and a possible 2nd
  *    time depending on memory configuration from stack+global context
  */
 void do_sdrc_init(u32 cs, u32 early)
 {
-       struct sdrc_actim *sdrc_actim_base;
-
-       if (cs)
-               sdrc_actim_base = (struct sdrc_actim *)SDRC_ACTIM_CTRL1_BASE;
-       else
-               sdrc_actim_base = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
+       struct sdrc_actim *sdrc_actim_base0, *sdrc_actim_base1;
 
        if (early) {
                /* reset sdrc controller */
@@ -138,24 +132,29 @@ void do_sdrc_init(u32 cs, u32 early)
                sdelay(0x20000);
        }
 
-       writel(RASWIDTH_13BITS | CASWIDTH_10BITS | ADDRMUXLEGACY |
-                       RAMSIZE_128 | BANKALLOCATION | B32NOT16 | B32NOT16 |
-                       DEEPPD | DDR_SDRAM, &sdrc_base->cs[cs].mcfg);
-       writel(ARCV | ARE_ARCV_1, &sdrc_base->cs[cs].rfr_ctrl);
-       writel(V_ACTIMA_165, &sdrc_actim_base->ctrla);
-       writel(V_ACTIMB_165, &sdrc_actim_base->ctrlb);
-
-       writel(CMD_NOP, &sdrc_base->cs[cs].manual);
-       writel(CMD_PRECHARGE, &sdrc_base->cs[cs].manual);
-       writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
-       writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
-
        /*
-        * CAS latency 3, Write Burst = Read Burst, Serial Mode,
-        * Burst length = 4
+        * SDRC timings are set up by x-load or config header
+        * We don't need to redo them here.
+        * Older x-loads configure only CS0
+        * configure CS1 to handle this ommission
         */
-       writel(CASL3 | BURSTLENGTH4, &sdrc_base->cs[cs].mr);
+       if (cs) {
+               sdrc_actim_base0 = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
+               sdrc_actim_base1 = (struct sdrc_actim *)SDRC_ACTIM_CTRL1_BASE;
+               writel(readl(&sdrc_base->cs[CS0].mcfg),
+                       &sdrc_base->cs[CS1].mcfg);
+               writel(readl(&sdrc_base->cs[CS0].rfr_ctrl),
+                       &sdrc_base->cs[CS1].rfr_ctrl);
+               writel(readl(&sdrc_actim_base0->ctrla),
+                       &sdrc_actim_base1->ctrla);
+               writel(readl(&sdrc_actim_base0->ctrlb),
+                       &sdrc_actim_base1->ctrlb);
+       }
 
+       /*
+        * Test ram in this bank
+        * Disable if bad or not present
+        */
        if (!mem_ok(cs))
                writel(0, &sdrc_base->cs[cs].mcfg);
 }