These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
config TARGET_GALAXY5200
bool "Support galaxy5200"
-config TARGET_ICECUBE
- bool "Support IceCube"
-
config TARGET_INKA4X0
bool "Support inka4x0"
config TARGET_V38B
bool "Support v38b"
-config TARGET_CPCI5200
- bool "Support cpci5200"
-
-config TARGET_MECP5200
- bool "Support mecp5200"
-
-config TARGET_PF5200
- bool "Support pf5200"
-
config TARGET_O2D
bool "Support O2D"
source "board/bc3450/Kconfig"
source "board/canmb/Kconfig"
source "board/cm5200/Kconfig"
-source "board/esd/cpci5200/Kconfig"
-source "board/esd/mecp5200/Kconfig"
-source "board/esd/pf5200/Kconfig"
source "board/galaxy5200/Kconfig"
-source "board/icecube/Kconfig"
source "board/ifm/o2dnt2/Kconfig"
source "board/inka4x0/Kconfig"
source "board/intercontrol/digsy_mtc/Kconfig"
*(volatile u32 *)MPC5XXX_PCI_CAR = (1 << 31) | dev | offset;
eieio();
udelay(10);
-#if (defined CONFIG_PF5200 || defined CONFIG_CPCI5200)
- if (dev & 0x00ff0000) {
- u32 val;
- val = in_le16((volatile u16 *)(CONFIG_PCI_IO_PHYS+2));
- udelay(10);
- val = val << 16;
- val |= in_le16((volatile u16 *)(CONFIG_PCI_IO_PHYS+0));
- *value = val;
- } else {
- *value = in_le32((volatile u32 *)CONFIG_PCI_IO_PHYS);
- }
- udelay(10);
-#else
*value = in_le32((volatile u32 *)CONFIG_PCI_IO_PHYS);
-#endif
eieio();
*(volatile u32 *)MPC5XXX_PCI_CAR = 0;
udelay(10);
+++ /dev/null
-if TARGET_CPCI5200
-
-config SYS_BOARD
- default "cpci5200"
-
-config SYS_VENDOR
- default "esd"
-
-config SYS_CONFIG_NAME
- default "cpci5200"
-
-endif
+++ /dev/null
-CPCI5200 BOARD
-M: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
-S: Maintained
-F: board/esd/cpci5200/
-F: include/configs/cpci5200.h
-F: configs/cpci5200_defconfig
+++ /dev/null
-#
-# (C) Copyright 2003-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-# Objects for Xilinx JTAG programming (CPLD)
-# CPLD = ../common/xilinx_jtag/lenval.o \
-# ../common/xilinx_jtag/micro.o \
-# ../common/xilinx_jtag/ports.o
-
-# obj-y = cpci5200.o flash.o $(CPLD)
-obj-y = cpci5200.o strataflash.o
+++ /dev/null
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * cpci5200.c - main board support/init for the esd cpci5200.
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-#include <pci.h>
-#include <command.h>
-#include <netdev.h>
-
-#include "mt46v16m16-75.h"
-
-void init_ata_reset(void);
-
-static void sdram_start(int hi_addr)
-{
- long hi_addr_bit = hi_addr ? 0x01000000 : 0;
-
- /* unlock mode register */
- *(vu_long *) MPC5XXX_SDRAM_CTRL =
- SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* precharge all banks */
- *(vu_long *) MPC5XXX_SDRAM_CTRL =
- SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* set mode register: extended mode */
- *(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
- __asm__ volatile ("sync");
-
- /* set mode register: reset DLL */
- *(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
- __asm__ volatile ("sync");
-
- /* precharge all banks */
- *(vu_long *) MPC5XXX_SDRAM_CTRL =
- SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* auto refresh */
- *(vu_long *) MPC5XXX_SDRAM_CTRL =
- SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* set mode register */
- *(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE;
- __asm__ volatile ("sync");
-
- /* normal operation */
- *(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
- __asm__ volatile ("sync");
-}
-
-/*
- * ATTENTION: Although partially referenced initdram does NOT make real use
- * use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE
- * is something else than 0x00000000.
- */
-
-phys_size_t initdram(int board_type)
-{
- ulong dramsize = 0;
- ulong test1, test2;
-
- /* setup SDRAM chip selects */
- *(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0x0000001e; /* 2G at 0x0 */
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x80000000; /* disabled */
- __asm__ volatile ("sync");
-
- /* setup config registers */
- *(vu_long *) MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
- *(vu_long *) MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
- __asm__ volatile ("sync");
-
- /* set tap delay */
- *(vu_long *) MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
- __asm__ volatile ("sync");
-
- /* find RAM size using SDRAM CS0 only */
- sdram_start(0);
- test1 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x80000000);
- sdram_start(1);
- test2 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x80000000);
-
- if (test1 > test2) {
- sdram_start(0);
- dramsize = test1;
- } else {
- dramsize = test2;
- }
-
- /* memory smaller than 1MB is impossible */
- if (dramsize < (1 << 20)) {
- dramsize = 0;
- }
-
- /* set SDRAM CS0 size according to the amount of RAM found */
- if (dramsize > 0) {
- *(vu_long *) MPC5XXX_SDRAM_CS0CFG =
- 0x13 + __builtin_ffs(dramsize >> 20) - 1;
- /* let SDRAM CS1 start right after CS0 */
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e; /* 2G */
- } else {
-#if 0
- *(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
- /* let SDRAM CS1 start right after CS0 */
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e; /* 2G */
-#else
- *(vu_long *) MPC5XXX_SDRAM_CS0CFG =
- 0x13 + __builtin_ffs(0x08000000 >> 20) - 1;
- /* let SDRAM CS1 start right after CS0 */
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x08000000 + 0x0000001e; /* 2G */
-#endif
- }
-
-#if 0
- /* find RAM size using SDRAM CS1 only */
- sdram_start(0);
- get_ram_size((ulong *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
- sdram_start(1);
- get_ram_size((ulong *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
- sdram_start(0);
-#endif
- /* set SDRAM CS1 size according to the amount of RAM found */
-
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
-
- init_ata_reset();
- return (dramsize);
-}
-
-int checkboard(void)
-{
- puts("Board: esd CPCI5200 (cpci5200)\n");
- return 0;
-}
-
-void flash_preinit(void)
-{
- /*
- * Now, when we are in RAM, enable flash write
- * access for detection process.
- * Note that CS_BOOT cannot be cleared when
- * executing in flash.
- */
- *(vu_long *) MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
-}
-
-void flash_afterinit(ulong size)
-{
- if (size == 0x02000000) {
- /* adjust mapping */
- *(vu_long *) MPC5XXX_BOOTCS_START =
- *(vu_long *) MPC5XXX_CS0_START =
- START_REG(CONFIG_SYS_BOOTCS_START | size);
- *(vu_long *) MPC5XXX_BOOTCS_STOP =
- *(vu_long *) MPC5XXX_CS0_STOP =
- STOP_REG(CONFIG_SYS_BOOTCS_START | size, size);
- }
-}
-
-#ifdef CONFIG_PCI
-static struct pci_controller hose;
-
-extern void pci_mpc5xxx_init(struct pci_controller *);
-
-void pci_init_board(void) {
- pci_mpc5xxx_init(&hose);
-}
-#endif
-
-#if defined(CONFIG_CMD_IDE) && defined (CONFIG_IDE_RESET)
-
-void init_ide_reset(void)
-{
- debug("init_ide_reset\n");
-
- /* Configure PSC1_4 as GPIO output for ATA reset */
- *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
- *(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
-}
-
-void ide_set_reset(int idereset)
-{
- debug("ide_reset(%d)\n", idereset);
-
- if (idereset) {
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
- } else {
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
- }
-}
-#endif
-
-#define MPC5XXX_SIMPLEIO_GPIO_ENABLE (MPC5XXX_GPIO + 0x0004)
-#define MPC5XXX_SIMPLEIO_GPIO_DIR (MPC5XXX_GPIO + 0x000C)
-#define MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT (MPC5XXX_GPIO + 0x0010)
-#define MPC5XXX_SIMPLEIO_GPIO_DATA_INPUT (MPC5XXX_GPIO + 0x0014)
-
-#define MPC5XXX_INTERRUPT_GPIO_ENABLE (MPC5XXX_GPIO + 0x0020)
-#define MPC5XXX_INTERRUPT_GPIO_DIR (MPC5XXX_GPIO + 0x0028)
-#define MPC5XXX_INTERRUPT_GPIO_DATA_OUTPUT (MPC5XXX_GPIO + 0x002C)
-#define MPC5XXX_INTERRUPT_GPIO_STATUS (MPC5XXX_GPIO + 0x003C)
-
-#define GPIO_WU6 0x40000000UL
-#define GPIO_USB0 0x00010000UL
-#define GPIO_USB9 0x08000000UL
-#define GPIO_USB9S 0x00080000UL
-
-void init_ata_reset(void)
-{
- debug("init_ata_reset\n");
-
- /* Configure GPIO_WU6 as GPIO output for ATA reset */
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_WU6;
- *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_WU6;
- *(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_WU6;
- __asm__ volatile ("sync");
-
- *(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT &= ~GPIO_USB0;
- *(vu_long *) MPC5XXX_SIMPLEIO_GPIO_ENABLE |= GPIO_USB0;
- *(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DIR |= GPIO_USB0;
- __asm__ volatile ("sync");
-
- *(vu_long *) MPC5XXX_INTERRUPT_GPIO_DATA_OUTPUT &= ~GPIO_USB9;
- *(vu_long *) MPC5XXX_INTERRUPT_GPIO_ENABLE &= ~GPIO_USB9;
- __asm__ volatile ("sync");
-
- if ((*(vu_long *) MPC5XXX_INTERRUPT_GPIO_STATUS & GPIO_USB9S) == 0) {
- *(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT |= GPIO_USB0;
- __asm__ volatile ("sync");
- }
-}
-
-int board_eth_init(bd_t *bis)
-{
- return pci_eth_init(bis);
-}
-
-int do_writepci(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
- unsigned int addr;
- unsigned int size;
- int i;
- volatile unsigned long *ptr;
-
- addr = simple_strtol(argv[1], NULL, 16);
- size = simple_strtol(argv[2], NULL, 16);
-
- printf("\nWriting at addr %08x, size %08x.\n", addr, size);
-
- while (1) {
- ptr = (volatile unsigned long *)addr;
- for (i = 0; i < (size >> 2); i++) {
- *ptr++ = i;
- }
-
- /* Abort if ctrl-c was pressed */
- if (ctrlc()) {
- puts("\nAbort\n");
- return 0;
- }
- putc('.');
- }
- return 0;
-}
-
-U_BOOT_CMD(writepci, 3, 1, do_writepci,
- "Write some data to pcibus",
- "<addr> <size>\n"
- ""
-);
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#define SDRAM_DDR 1 /* is DDR */
-
-/* Settings for XLB = 132 MHz */
-#define SDRAM_MODE 0x018D0000
-#define SDRAM_EMODE 0x40090000
-#define SDRAM_CONTROL 0x705f0f00
-#define SDRAM_CONFIG1 0x73722930
-#define SDRAM_CONFIG2 0x47770000
-#define SDRAM_TAPDELAY 0x10000000
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Brad Kemp, Seranoa Networks, Brad.Kemp@seranoa.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/processor.h>
-#include <asm/cache.h>
-
-#undef DEBUG_FLASH
-/*
- * This file implements a Common Flash Interface (CFI) driver for U-Boot.
- * The width of the port and the width of the chips are determined at initialization.
- * These widths are used to calculate the address for access CFI data structures.
- * It has been tested on an Intel Strataflash implementation.
- *
- * References
- * JEDEC Standard JESD68 - Common Flash Interface (CFI)
- * JEDEC Standard JEP137-A Common Flash Interface (CFI) ID Codes
- * Intel Application Note 646 Common Flash Interface (CFI) and Command Sets
- * Intel 290667-008 3 Volt Intel StrataFlash Memory datasheet
- *
- * TODO
- * Use Primary Extended Query table (PRI) and Alternate Algorithm Query Table (ALT) to determine if protection is available
- * Add support for other command sets Use the PRI and ALT to determine command set
- * Verify erase and program timeouts.
- */
-
-#define FLASH_CMD_CFI 0x98
-#define FLASH_CMD_READ_ID 0x90
-#define FLASH_CMD_RESET 0xff
-#define FLASH_CMD_BLOCK_ERASE 0x20
-#define FLASH_CMD_ERASE_CONFIRM 0xD0
-#define FLASH_CMD_WRITE 0x40
-#define FLASH_CMD_PROTECT 0x60
-#define FLASH_CMD_PROTECT_SET 0x01
-#define FLASH_CMD_PROTECT_CLEAR 0xD0
-#define FLASH_CMD_CLEAR_STATUS 0x50
-#define FLASH_CMD_WRITE_TO_BUFFER 0xE8
-#define FLASH_CMD_WRITE_BUFFER_CONFIRM 0xD0
-
-#define FLASH_STATUS_DONE 0x80
-#define FLASH_STATUS_ESS 0x40
-#define FLASH_STATUS_ECLBS 0x20
-#define FLASH_STATUS_PSLBS 0x10
-#define FLASH_STATUS_VPENS 0x08
-#define FLASH_STATUS_PSS 0x04
-#define FLASH_STATUS_DPS 0x02
-#define FLASH_STATUS_R 0x01
-#define FLASH_STATUS_PROTECT 0x01
-
-#define FLASH_OFFSET_CFI 0x55
-#define FLASH_OFFSET_CFI_RESP 0x10
-#define FLASH_OFFSET_WTOUT 0x1F
-#define FLASH_OFFSET_WBTOUT 0x20
-#define FLASH_OFFSET_ETOUT 0x21
-#define FLASH_OFFSET_CETOUT 0x22
-#define FLASH_OFFSET_WMAX_TOUT 0x23
-#define FLASH_OFFSET_WBMAX_TOUT 0x24
-#define FLASH_OFFSET_EMAX_TOUT 0x25
-#define FLASH_OFFSET_CEMAX_TOUT 0x26
-#define FLASH_OFFSET_SIZE 0x27
-#define FLASH_OFFSET_INTERFACE 0x28
-#define FLASH_OFFSET_BUFFER_SIZE 0x2A
-#define FLASH_OFFSET_NUM_ERASE_REGIONS 0x2C
-#define FLASH_OFFSET_ERASE_REGIONS 0x2D
-#define FLASH_OFFSET_PROTECT 0x02
-#define FLASH_OFFSET_USER_PROTECTION 0x85
-#define FLASH_OFFSET_INTEL_PROTECTION 0x81
-
-#define FLASH_MAN_CFI 0x01000000
-
-typedef union {
- unsigned char c;
- unsigned short w;
- unsigned long l;
-} cfiword_t;
-
-typedef union {
- unsigned char *cp;
- unsigned short *wp;
- unsigned long *lp;
-} cfiptr_t;
-
-#define NUM_ERASE_REGIONS 4
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-
-static void flash_add_byte(flash_info_t * info, cfiword_t * cword, uchar c);
-static void flash_make_cmd(flash_info_t * info, uchar cmd, void *cmdbuf);
-static void flash_write_cmd(flash_info_t * info, int sect, uchar offset,
- uchar cmd);
-static int flash_isequal(flash_info_t * info, int sect, uchar offset,
- uchar cmd);
-static int flash_isset(flash_info_t * info, int sect, uchar offset, uchar cmd);
-static int flash_detect_cfi(flash_info_t * info);
-static ulong flash_get_size(ulong base, int banknum);
-static int flash_write_cfiword(flash_info_t * info, ulong dest,
- cfiword_t cword);
-static int flash_full_status_check(flash_info_t * info, ulong sector,
- ulong tout, char *prompt);
-#ifdef CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-static int flash_write_cfibuffer(flash_info_t * info, ulong dest, uchar * cp,
- int len);
-#endif
-/*-----------------------------------------------------------------------
- * create an address based on the offset and the port width
- */
-inline uchar *flash_make_addr(flash_info_t * info, int sect, int offset)
-{
- return ((uchar *) (info->start[sect] + (offset * info->portwidth)));
-}
-
-/*-----------------------------------------------------------------------
- * read a character at a port width address
- */
-inline uchar flash_read_uchar(flash_info_t * info, uchar offset)
-{
- uchar *cp;
- cp = flash_make_addr(info, 0, offset);
- return (cp[info->portwidth - 1]);
-}
-
-/*-----------------------------------------------------------------------
- * read a short word by swapping for ppc format.
- */
-ushort flash_read_ushort(flash_info_t * info, int sect, uchar offset)
-{
- uchar *addr;
-
- addr = flash_make_addr(info, sect, offset);
- return ((addr[(2 * info->portwidth) - 1] << 8) |
- addr[info->portwidth - 1]);
-
-}
-
-/*-----------------------------------------------------------------------
- * read a long word by picking the least significant byte of each maiximum
- * port size word. Swap for ppc format.
- */
-ulong flash_read_long(flash_info_t * info, int sect, uchar offset)
-{
- uchar *addr;
-
- addr = flash_make_addr(info, sect, offset);
- return ((addr[(2 * info->portwidth) - 1] << 24) |
- (addr[(info->portwidth) - 1] << 16) |
- (addr[(4 * info->portwidth) - 1] << 8) |
- addr[(3 * info->portwidth) - 1]);
-
-}
-
-/*-----------------------------------------------------------------------
- */
-unsigned long flash_init(void)
-{
- unsigned long size;
- int i;
- unsigned long address;
-
- /* The flash is positioned back to back, with the demultiplexing of the chip
- * based on the A24 address line.
- *
- */
-
- address = CONFIG_SYS_FLASH_BASE;
- size = 0;
-
- /* Init: no FLASHes known */
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- size += flash_info[i].size = flash_get_size(address, i);
- address += CONFIG_SYS_FLASH_INCREMENT;
- if (flash_info[i].flash_id == FLASH_UNKNOWN) {
- printf
- ("## Unknown FLASH on Bank %d - Size = 0x%08lx = %ld MB\n",
- i, flash_info[0].size, flash_info[i].size << 20);
- }
- }
-
-#if 0 /* test-only */
- /* Monitor protection ON by default */
-#if (CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE)
- for (i = 0;
- flash_info[0].start[i] < CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1;
- i++)
- (void)flash_real_protect(&flash_info[0], i, 1);
-#endif
-#endif
-
- return (size);
-}
-
-/*-----------------------------------------------------------------------
- */
-int flash_erase(flash_info_t * info, int s_first, int s_last)
-{
- int rcode = 0;
- int prot;
- int sect;
-
- if (info->flash_id != FLASH_MAN_CFI) {
- printf("Can't erase unknown flash type - aborted\n");
- return 1;
- }
- if ((s_first < 0) || (s_first > s_last)) {
- printf("- no sectors to erase\n");
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
- if (prot) {
- printf("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf("\n");
- }
-
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- flash_write_cmd(info, sect, 0, FLASH_CMD_CLEAR_STATUS);
- flash_write_cmd(info, sect, 0, FLASH_CMD_BLOCK_ERASE);
- flash_write_cmd(info, sect, 0, FLASH_CMD_ERASE_CONFIRM);
-
- if (flash_full_status_check
- (info, sect, info->erase_blk_tout, "erase")) {
- rcode = 1;
- } else
- printf(".");
- }
- }
- printf(" done\n");
- return rcode;
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info(flash_info_t * info)
-{
- int i;
-
- if (info->flash_id != FLASH_MAN_CFI) {
- printf("missing or unknown FLASH type\n");
- return;
- }
-
- printf("CFI conformant FLASH (%d x %d)",
- (info->portwidth << 3), (info->chipwidth << 3));
- printf(" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
- printf
- (" Erase timeout %ld ms, write timeout %ld ms, buffer write timeout %ld ms, buffer size %d\n",
- info->erase_blk_tout, info->write_tout, info->buffer_write_tout,
- info->buffer_size);
-
- printf(" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf("\n");
- printf(" %08lX%5s",
- info->start[i], info->protect[i] ? " (RO)" : " ");
- }
- printf("\n");
- return;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-int write_buff(flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- ulong wp;
- ulong cp;
- int aln;
- cfiword_t cword;
- int i, rc;
-
- /* get lower aligned address */
- wp = (addr & ~(info->portwidth - 1));
-
- /* handle unaligned start */
- if ((aln = addr - wp) != 0) {
- cword.l = 0;
- cp = wp;
- for (i = 0; i < aln; ++i, ++cp)
- flash_add_byte(info, &cword, (*(uchar *) cp));
-
- for (; (i < info->portwidth) && (cnt > 0); i++) {
- flash_add_byte(info, &cword, *src++);
- cnt--;
- cp++;
- }
- for (; (cnt == 0) && (i < info->portwidth); ++i, ++cp)
- flash_add_byte(info, &cword, (*(uchar *) cp));
- if ((rc = flash_write_cfiword(info, wp, cword)) != 0)
- return rc;
- wp = cp;
- }
-#ifdef CONFIG_SYS_FLASH_USE_BUFFER_WRITE
- while (cnt >= info->portwidth) {
- i = info->buffer_size > cnt ? cnt : info->buffer_size;
- if ((rc = flash_write_cfibuffer(info, wp, src, i)) != ERR_OK)
- return rc;
- wp += i;
- src += i;
- cnt -= i;
- }
-#else
- /* handle the aligned part */
- while (cnt >= info->portwidth) {
- cword.l = 0;
- for (i = 0; i < info->portwidth; i++) {
- flash_add_byte(info, &cword, *src++);
- }
- if ((rc = flash_write_cfiword(info, wp, cword)) != 0)
- return rc;
- wp += info->portwidth;
- cnt -= info->portwidth;
- }
-#endif /* CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- cword.l = 0;
- for (i = 0, cp = wp; (i < info->portwidth) && (cnt > 0); ++i, ++cp) {
- flash_add_byte(info, &cword, *src++);
- --cnt;
- }
- for (; i < info->portwidth; ++i, ++cp) {
- flash_add_byte(info, &cword, (*(uchar *) cp));
- }
-
- return flash_write_cfiword(info, wp, cword);
-}
-
-/*-----------------------------------------------------------------------
- */
-int flash_real_protect(flash_info_t * info, long sector, int prot)
-{
- int retcode = 0;
-
- flash_write_cmd(info, sector, 0, FLASH_CMD_CLEAR_STATUS);
- flash_write_cmd(info, sector, 0, FLASH_CMD_PROTECT);
- if (prot)
- flash_write_cmd(info, sector, 0, FLASH_CMD_PROTECT_SET);
- else
- flash_write_cmd(info, sector, 0, FLASH_CMD_PROTECT_CLEAR);
-
- if ((retcode =
- flash_full_status_check(info, sector, info->erase_blk_tout,
- prot ? "protect" : "unprotect")) == 0) {
-
- info->protect[sector] = prot;
- /* Intel's unprotect unprotects all locking */
- if (prot == 0) {
- int i;
- for (i = 0; i < info->sector_count; i++) {
- if (info->protect[i])
- flash_real_protect(info, i, 1);
- }
- }
- }
-
- return retcode;
-}
-
-/*-----------------------------------------------------------------------
- * wait for XSR.7 to be set. Time out with an error if it does not.
- * This routine does not set the flash to read-array mode.
- */
-static int flash_status_check(flash_info_t * info, ulong sector, ulong tout,
- char *prompt)
-{
- ulong start;
-
- /* Wait for command completion */
- start = get_timer(0);
- while (!flash_isset(info, sector, 0, FLASH_STATUS_DONE)) {
- if (get_timer(start) > info->erase_blk_tout) {
- printf("Flash %s timeout at address %lx\n", prompt,
- info->start[sector]);
- flash_write_cmd(info, sector, 0, FLASH_CMD_RESET);
- return ERR_TIMOUT;
- }
- }
- return ERR_OK;
-}
-
-/*-----------------------------------------------------------------------
- * Wait for XSR.7 to be set, if it times out print an error, otherwise do a full status check.
- * This routine sets the flash to read-array mode.
- */
-static int flash_full_status_check(flash_info_t * info, ulong sector,
- ulong tout, char *prompt)
-{
- int retcode;
- retcode = flash_status_check(info, sector, tout, prompt);
- if ((retcode == ERR_OK)
- && !flash_isequal(info, sector, 0, FLASH_STATUS_DONE)) {
- retcode = ERR_INVAL;
- printf("Flash %s error at address %lx\n", prompt,
- info->start[sector]);
- if (flash_isset
- (info, sector, 0,
- FLASH_STATUS_ECLBS | FLASH_STATUS_PSLBS)) {
- printf("Command Sequence Error.\n");
- } else if (flash_isset(info, sector, 0, FLASH_STATUS_ECLBS)) {
- printf("Block Erase Error.\n");
- retcode = ERR_NOT_ERASED;
- } else if (flash_isset(info, sector, 0, FLASH_STATUS_PSLBS)) {
- printf("Locking Error\n");
- }
- if (flash_isset(info, sector, 0, FLASH_STATUS_DPS)) {
- printf("Block locked.\n");
- retcode = ERR_PROTECTED;
- }
- if (flash_isset(info, sector, 0, FLASH_STATUS_VPENS))
- printf("Vpp Low Error.\n");
- }
- flash_write_cmd(info, sector, 0, FLASH_CMD_RESET);
- return retcode;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_add_byte(flash_info_t * info, cfiword_t * cword, uchar c)
-{
- switch (info->portwidth) {
- case FLASH_CFI_8BIT:
- cword->c = c;
- break;
- case FLASH_CFI_16BIT:
- cword->w = (cword->w << 8) | c;
- break;
- case FLASH_CFI_32BIT:
- cword->l = (cword->l << 8) | c;
- }
-}
-
-/*-----------------------------------------------------------------------
- * make a proper sized command based on the port and chip widths
- */
-static void flash_make_cmd(flash_info_t * info, uchar cmd, void *cmdbuf)
-{
- int i;
- uchar *cp = (uchar *) cmdbuf;
- for (i = 0; i < info->portwidth; i++)
- *cp++ = ((i + 1) % info->chipwidth) ? '\0' : cmd;
-}
-
-/*
- * Write a proper sized command to the correct address
- */
-static void flash_write_cmd(flash_info_t * info, int sect, uchar offset,
- uchar cmd)
-{
-
- volatile cfiptr_t addr;
- cfiword_t cword;
- addr.cp = flash_make_addr(info, sect, offset);
- flash_make_cmd(info, cmd, &cword);
- switch (info->portwidth) {
- case FLASH_CFI_8BIT:
- *addr.cp = cword.c;
- break;
- case FLASH_CFI_16BIT:
- *addr.wp = cword.w;
- break;
- case FLASH_CFI_32BIT:
- *addr.lp = cword.l;
- break;
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-static int flash_isequal(flash_info_t * info, int sect, uchar offset, uchar cmd)
-{
- cfiptr_t cptr;
- cfiword_t cword;
- int retval;
- cptr.cp = flash_make_addr(info, sect, offset);
- flash_make_cmd(info, cmd, &cword);
- switch (info->portwidth) {
- case FLASH_CFI_8BIT:
- retval = (cptr.cp[0] == cword.c);
- break;
- case FLASH_CFI_16BIT:
- retval = (cptr.wp[0] == cword.w);
- break;
- case FLASH_CFI_32BIT:
- retval = (cptr.lp[0] == cword.l);
- break;
- default:
- retval = 0;
- break;
- }
- return retval;
-}
-
-/*-----------------------------------------------------------------------
- */
-static int flash_isset(flash_info_t * info, int sect, uchar offset, uchar cmd)
-{
- cfiptr_t cptr;
- cfiword_t cword;
- int retval;
- cptr.cp = flash_make_addr(info, sect, offset);
- flash_make_cmd(info, cmd, &cword);
- switch (info->portwidth) {
- case FLASH_CFI_8BIT:
- retval = ((cptr.cp[0] & cword.c) == cword.c);
- break;
- case FLASH_CFI_16BIT:
- retval = ((cptr.wp[0] & cword.w) == cword.w);
- break;
- case FLASH_CFI_32BIT:
- retval = ((cptr.lp[0] & cword.l) == cword.l);
- break;
- default:
- retval = 0;
- break;
- }
- return retval;
-}
-
-/*-----------------------------------------------------------------------
- * detect if flash is compatible with the Common Flash Interface (CFI)
- * http://www.jedec.org/download/search/jesd68.pdf
- *
- */
-static int flash_detect_cfi(flash_info_t * info)
-{
-
- for (info->portwidth = FLASH_CFI_8BIT;
- info->portwidth <= FLASH_CFI_32BIT; info->portwidth <<= 1) {
- for (info->chipwidth = FLASH_CFI_BY8;
- info->chipwidth <= info->portwidth;
- info->chipwidth <<= 1) {
- flash_write_cmd(info, 0, 0, FLASH_CMD_RESET);
- flash_write_cmd(info, 0, FLASH_OFFSET_CFI,
- FLASH_CMD_CFI);
- if (flash_isequal(info, 0, FLASH_OFFSET_CFI_RESP, 'Q')
- && flash_isequal(info, 0, FLASH_OFFSET_CFI_RESP + 1,
- 'R')
- && flash_isequal(info, 0, FLASH_OFFSET_CFI_RESP + 2,
- 'Y'))
- return 1;
- }
- }
- return 0;
-}
-
-/*
- * The following code cannot be run from FLASH!
- *
- */
-static ulong flash_get_size(ulong base, int banknum)
-{
- flash_info_t *info = &flash_info[banknum];
- int i, j;
- int sect_cnt;
- unsigned long sector;
- unsigned long tmp;
- int size_ratio = 0;
- uchar num_erase_regions;
- int erase_region_size;
- int erase_region_count;
-
- info->start[0] = base;
-#if 0
- invalidate_dcache_range(base, base + 0x400);
-#endif
- if (flash_detect_cfi(info)) {
-
- size_ratio = info->portwidth / info->chipwidth;
- num_erase_regions =
- flash_read_uchar(info, FLASH_OFFSET_NUM_ERASE_REGIONS);
-
- sect_cnt = 0;
- sector = base;
- for (i = 0; i < num_erase_regions; i++) {
- if (i > NUM_ERASE_REGIONS) {
- printf("%d erase regions found, only %d used\n",
- num_erase_regions, NUM_ERASE_REGIONS);
- break;
- }
- tmp =
- flash_read_long(info, 0,
- FLASH_OFFSET_ERASE_REGIONS);
- erase_region_size =
- (tmp & 0xffff) ? ((tmp & 0xffff) * 256) : 128;
- tmp >>= 16;
- erase_region_count = (tmp & 0xffff) + 1;
- for (j = 0; j < erase_region_count; j++) {
- info->start[sect_cnt] = sector;
- sector += (erase_region_size * size_ratio);
- info->protect[sect_cnt] =
- flash_isset(info, sect_cnt,
- FLASH_OFFSET_PROTECT,
- FLASH_STATUS_PROTECT);
- sect_cnt++;
- }
- }
-
- info->sector_count = sect_cnt;
- /* multiply the size by the number of chips */
- info->size =
- (1 << flash_read_uchar(info, FLASH_OFFSET_SIZE)) *
- size_ratio;
- info->buffer_size =
- (1 << flash_read_ushort(info, 0, FLASH_OFFSET_BUFFER_SIZE));
- tmp = 1 << flash_read_uchar(info, FLASH_OFFSET_ETOUT);
- info->erase_blk_tout =
- (tmp *
- (1 << flash_read_uchar(info, FLASH_OFFSET_EMAX_TOUT)));
- tmp = 1 << flash_read_uchar(info, FLASH_OFFSET_WBTOUT);
- info->buffer_write_tout =
- (tmp *
- (1 << flash_read_uchar(info, FLASH_OFFSET_WBMAX_TOUT)));
- tmp = 1 << flash_read_uchar(info, FLASH_OFFSET_WTOUT);
- info->write_tout =
- (tmp *
- (1 << flash_read_uchar(info, FLASH_OFFSET_WMAX_TOUT))) /
- 1000;
- info->flash_id = FLASH_MAN_CFI;
- }
-
- flash_write_cmd(info, 0, 0, FLASH_CMD_RESET);
-#ifdef DEBUG_FLASH
- printf("portwidth=%d chipwidth=%d\n", info->portwidth, info->chipwidth); /* test-only */
-#endif
-#ifdef DEBUG_FLASH
- printf("found %d erase regions\n", num_erase_regions);
-#endif
-#ifdef DEBUG_FLASH
- printf("size=%08x sectors=%08x \n", info->size, info->sector_count);
-#endif
- return (info->size);
-}
-
-/*-----------------------------------------------------------------------
- */
-static int flash_write_cfiword(flash_info_t * info, ulong dest, cfiword_t cword)
-{
-
- cfiptr_t cptr;
- int flag;
-
- cptr.cp = (uchar *)dest;
-
- /* Check if Flash is (sufficiently) erased */
- switch (info->portwidth) {
- case FLASH_CFI_8BIT:
- flag = ((cptr.cp[0] & cword.c) == cword.c);
- break;
- case FLASH_CFI_16BIT:
- flag = ((cptr.wp[0] & cword.w) == cword.w);
- break;
- case FLASH_CFI_32BIT:
- flag = ((cptr.lp[0] & cword.l) == cword.l);
- break;
- default:
- return 2;
- }
- if (!flag)
- return 2;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- flash_write_cmd(info, 0, 0, FLASH_CMD_CLEAR_STATUS);
- flash_write_cmd(info, 0, 0, FLASH_CMD_WRITE);
-
- switch (info->portwidth) {
- case FLASH_CFI_8BIT:
- cptr.cp[0] = cword.c;
- break;
- case FLASH_CFI_16BIT:
- cptr.wp[0] = cword.w;
- break;
- case FLASH_CFI_32BIT:
- cptr.lp[0] = cword.l;
- break;
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- return flash_full_status_check(info, 0, info->write_tout, "write");
-}
-
-#ifdef CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-
-/* loop through the sectors from the highest address
- * when the passed address is greater or equal to the sector address
- * we have a match
- */
-static int find_sector(flash_info_t * info, ulong addr)
-{
- int sector;
- for (sector = info->sector_count - 1; sector >= 0; sector--) {
- if (addr >= info->start[sector])
- break;
- }
- return sector;
-}
-
-static int flash_write_cfibuffer(flash_info_t * info, ulong dest, uchar * cp,
- int len)
-{
-
- int sector;
- int cnt;
- int retcode;
- volatile cfiptr_t src;
- volatile cfiptr_t dst;
-
- src.cp = cp;
- dst.cp = (uchar *) dest;
- sector = find_sector(info, dest);
- flash_write_cmd(info, sector, 0, FLASH_CMD_CLEAR_STATUS);
- flash_write_cmd(info, sector, 0, FLASH_CMD_WRITE_TO_BUFFER);
- if ((retcode = flash_status_check(info, sector, info->buffer_write_tout,
- "write to buffer")) == ERR_OK) {
- switch (info->portwidth) {
- case FLASH_CFI_8BIT:
- cnt = len;
- break;
- case FLASH_CFI_16BIT:
- cnt = len >> 1;
- break;
- case FLASH_CFI_32BIT:
- cnt = len >> 2;
- break;
- default:
- return ERR_INVAL;
- break;
- }
- flash_write_cmd(info, sector, 0, (uchar) cnt - 1);
- while (cnt-- > 0) {
- switch (info->portwidth) {
- case FLASH_CFI_8BIT:
- *dst.cp++ = *src.cp++;
- break;
- case FLASH_CFI_16BIT:
- *dst.wp++ = *src.wp++;
- break;
- case FLASH_CFI_32BIT:
- *dst.lp++ = *src.lp++;
- break;
- default:
- return ERR_INVAL;
- break;
- }
- }
- flash_write_cmd(info, sector, 0,
- FLASH_CMD_WRITE_BUFFER_CONFIRM);
- retcode =
- flash_full_status_check(info, sector,
- info->buffer_write_tout,
- "buffer write");
- }
- flash_write_cmd(info, sector, 0, FLASH_CMD_CLEAR_STATUS);
- return retcode;
-}
-#endif /* CONFIG_SYS_USE_FLASH_BUFFER_WRITE */
+++ /dev/null
-if TARGET_MECP5200
-
-config SYS_BOARD
- default "mecp5200"
-
-config SYS_VENDOR
- default "esd"
-
-config SYS_CONFIG_NAME
- default "mecp5200"
-
-endif
+++ /dev/null
-MECP5200 BOARD
-M: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
-S: Maintained
-F: board/esd/mecp5200/
-F: include/configs/mecp5200.h
-F: configs/mecp5200_defconfig
+++ /dev/null
-#
-# (C) Copyright 2003-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = mecp5200.o
+++ /dev/null
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * pf5200.c - main board support/init for the esd pf5200.
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-#include <pci.h>
-#include <command.h>
-#include <netdev.h>
-
-#include "mt46v16m16-75.h"
-
-void init_power_switch(void);
-
-static void sdram_start(int hi_addr)
-{
- long hi_addr_bit = hi_addr ? 0x01000000 : 0;
-
- /* unlock mode register */
- *(vu_long *) MPC5XXX_SDRAM_CTRL =
- SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* precharge all banks */
- *(vu_long *) MPC5XXX_SDRAM_CTRL =
- SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* set mode register: extended mode */
- *(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
- __asm__ volatile ("sync");
-
- /* set mode register: reset DLL */
- *(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
- __asm__ volatile ("sync");
-
- /* precharge all banks */
- *(vu_long *) MPC5XXX_SDRAM_CTRL =
- SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* auto refresh */
- *(vu_long *) MPC5XXX_SDRAM_CTRL =
- SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* set mode register */
- *(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE;
- __asm__ volatile ("sync");
-
- /* normal operation */
- *(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
- __asm__ volatile ("sync");
-}
-
-/*
- * ATTENTION: Although partially referenced initdram does NOT make real use
- * use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE
- * is something else than 0x00000000.
- */
-
-phys_size_t initdram(int board_type)
-{
- ulong dramsize = 0;
- ulong test1, test2;
-
- /* setup SDRAM chip selects */
- *(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0x0000001e; /* 2G at 0x0 */
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x80000000; /* disabled */
- __asm__ volatile ("sync");
-
- /* setup config registers */
- *(vu_long *) MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
- *(vu_long *) MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
- __asm__ volatile ("sync");
-
- /* set tap delay */
- *(vu_long *) MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
- __asm__ volatile ("sync");
-
- /* find RAM size using SDRAM CS0 only */
- sdram_start(0);
- test1 = get_ram_size(CONFIG_SYS_SDRAM_BASE, 0x80000000);
- sdram_start(1);
- test2 = get_ram_size(CONFIG_SYS_SDRAM_BASE, 0x80000000);
-
- if (test1 > test2) {
- sdram_start(0);
- dramsize = test1;
- } else {
- dramsize = test2;
- }
-
- /* memory smaller than 1MB is impossible */
- if (dramsize < (1 << 20))
- dramsize = 0;
-
- /* set SDRAM CS0 size according to the amount of RAM found */
- if (dramsize > 0) {
- *(vu_long *) MPC5XXX_SDRAM_CS0CFG =
- 0x13 + __builtin_ffs(dramsize >> 20) - 1;
- /* let SDRAM CS1 start right after CS0 */
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e; /* 2G */
- } else {
-#if 0
- *(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
- /* let SDRAM CS1 start right after CS0 */
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e; /* 2G */
-#else
- *(vu_long *) MPC5XXX_SDRAM_CS0CFG =
- 0x13 + __builtin_ffs(0x08000000 >> 20) - 1;
- /* let SDRAM CS1 start right after CS0 */
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x08000000 + 0x0000001e; /* 2G */
-#endif
- }
-
-#if 0
- /* find RAM size using SDRAM CS1 only */
- sdram_start(0);
- get_ram_size((ulong *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
- sdram_start(1);
- get_ram_size((ulong *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
- sdram_start(0);
-#endif
- /* set SDRAM CS1 size according to the amount of RAM found */
-
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
-
- init_power_switch();
- return (dramsize);
-}
-
-int checkboard(void)
-{
- puts("Board: esd CPX CPU5200 (mecp5200)\n");
- return 0;
-}
-
-void flash_preinit(void)
-{
- /*
- * Now, when we are in RAM, enable flash write
- * access for detection process.
- * Note that CS_BOOT cannot be cleared when
- * executing in flash.
- */
- *(vu_long *) MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
-}
-
-void flash_afterinit(ulong size)
-{
- if (size == CONFIG_SYS_FLASH_SIZE) {
- /* adjust mapping */
- *(vu_long *) MPC5XXX_BOOTCS_START =
- *(vu_long *) MPC5XXX_CS0_START =
- START_REG(CONFIG_SYS_BOOTCS_START | size);
- *(vu_long *) MPC5XXX_BOOTCS_STOP =
- *(vu_long *) MPC5XXX_CS0_STOP =
- STOP_REG(CONFIG_SYS_BOOTCS_START | size, size);
- }
-}
-
-#ifdef CONFIG_PCI
-static struct pci_controller hose;
-
-extern void pci_mpc5xxx_init(struct pci_controller *);
-
-void pci_init_board(void)
-{
- pci_mpc5xxx_init(&hose);
-}
-#endif
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
-
-#define GPIO_PSC1_4 0x01000000UL
-
-void init_ide_reset(void)
-{
- debug("init_ide_reset\n");
-
- /* Configure PSC1_4 as GPIO output for ATA reset */
- *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
- *(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
-}
-
-void ide_set_reset(int idereset)
-{
- debug("ide_reset(%d)\n", idereset);
-
- if (idereset)
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
- else
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
-}
-#endif
-
-#define MPC5XXX_SIMPLEIO_GPIO_ENABLE (MPC5XXX_GPIO + 0x0004)
-#define MPC5XXX_SIMPLEIO_GPIO_DIR (MPC5XXX_GPIO + 0x000C)
-#define MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT (MPC5XXX_GPIO + 0x0010)
-#define MPC5XXX_SIMPLEIO_GPIO_DATA_INPUT (MPC5XXX_GPIO + 0x0014)
-
-#define MPC5XXX_INTERRUPT_GPIO_ENABLE (MPC5XXX_GPIO + 0x0020)
-#define MPC5XXX_INTERRUPT_GPIO_DIR (MPC5XXX_GPIO + 0x0028)
-#define MPC5XXX_INTERRUPT_GPIO_DATA_OUTPUT (MPC5XXX_GPIO + 0x002C)
-#define MPC5XXX_INTERRUPT_GPIO_STATUS (MPC5XXX_GPIO + 0x003C)
-
-#define GPIO_WU6 0x40000000UL
-#define GPIO_USB0 0x00010000UL
-#define GPIO_USB9 0x08000000UL
-#define GPIO_USB9S 0x00080000UL
-
-void init_power_switch(void)
-{
- debug("init_power_switch\n");
-
- /* Configure GPIO_WU6 as GPIO output for ATA reset */
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_WU6;
- *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_WU6;
- *(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_WU6;
- __asm__ volatile ("sync");
-
- *(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT &= ~GPIO_USB0;
- *(vu_long *) MPC5XXX_SIMPLEIO_GPIO_ENABLE |= GPIO_USB0;
- *(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DIR |= GPIO_USB0;
- __asm__ volatile ("sync");
-
- *(vu_long *) MPC5XXX_INTERRUPT_GPIO_DATA_OUTPUT &= ~GPIO_USB9;
- *(vu_long *) MPC5XXX_INTERRUPT_GPIO_ENABLE &= ~GPIO_USB9;
- __asm__ volatile ("sync");
-
- if ((*(vu_long *) MPC5XXX_INTERRUPT_GPIO_STATUS & GPIO_USB9S) == 0) {
- *(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT |= GPIO_USB0;
- __asm__ volatile ("sync");
- }
-}
-
-int board_eth_init(bd_t *bis)
-{
- return pci_eth_init(bis);
-}
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#define SDRAM_DDR 1 /* is DDR */
-
-/* Settings for XLB = 132 MHz */
-#define SDRAM_MODE 0x018D0000
-#define SDRAM_EMODE 0x40090000
-#define SDRAM_CONTROL 0x705f0f00
-#define SDRAM_CONFIG1 0x73722930
-#define SDRAM_CONFIG2 0x47770000
-#define SDRAM_TAPDELAY 0x10000000
+++ /dev/null
-if TARGET_PF5200
-
-config SYS_BOARD
- default "pf5200"
-
-config SYS_VENDOR
- default "esd"
-
-config SYS_CONFIG_NAME
- default "pf5200"
-
-endif
+++ /dev/null
-PF5200 BOARD
-M: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
-S: Maintained
-F: board/esd/pf5200/
-F: include/configs/pf5200.h
-F: configs/pf5200_defconfig
+++ /dev/null
-#
-# (C) Copyright 2003-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-# Objects for Xilinx JTAG programming (CPLD)
-# CPLD = ../common/xilinx_jtag/lenval.o \
-# ../common/xilinx_jtag/micro.o \
-# ../common/xilinx_jtag/ports.o
-
-# obj-y = pf5200.o flash.o $(CPLD)
-obj-y = pf5200.o flash.o
+++ /dev/null
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-typedef unsigned short FLASH_PORT_WIDTH;
-typedef volatile unsigned short FLASH_PORT_WIDTHV;
-
-#define FLASH_ID_MASK 0x00FF
-
-#define FPW FLASH_PORT_WIDTH
-#define FPWV FLASH_PORT_WIDTHV
-
-#define FLASH_CYCLE1 0x0555
-#define FLASH_CYCLE2 0x0aaa
-#define FLASH_ID1 0x00
-#define FLASH_ID2 0x01
-#define FLASH_ID3 0x0E
-#define FLASH_ID4 0x0F
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size(FPWV * addr, flash_info_t * info);
-static void flash_reset(flash_info_t * info);
-static int write_word_amd(flash_info_t * info, FPWV * dest, FPW data);
-static flash_info_t *flash_get_info(ulong base);
-
-/*-----------------------------------------------------------------------
- * flash_init()
- *
- * sets up flash_info and returns size of FLASH (bytes)
- */
-unsigned long flash_init(void)
-{
- unsigned long size = 0;
- int i = 0;
- extern void flash_preinit(void);
- extern void flash_afterinit(uint, ulong, ulong);
-
- ulong flashbase = CONFIG_SYS_FLASH_BASE;
-
- flash_preinit();
-
- /* There is only ONE FLASH device */
- memset(&flash_info[i], 0, sizeof(flash_info_t));
- flash_info[i].size = flash_get_size((FPW *) flashbase, &flash_info[i]);
- size += flash_info[i].size;
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET, CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
- flash_get_info(CONFIG_SYS_MONITOR_BASE));
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- flash_protect(FLAG_PROTECT_SET, CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1,
- flash_get_info(CONFIG_ENV_ADDR));
-#endif
-
- flash_afterinit(i, flash_info[i].start[0], flash_info[i].size);
- return size ? size : 1;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_reset(flash_info_t * info) {
- FPWV *base = (FPWV *) (info->start[0]);
-
- /* Put FLASH back in read mode */
- if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
- *base = (FPW) 0x00FF00FF; /* Intel Read Mode */
- } else if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_AMD) {
- *base = (FPW) 0x00F000F0; /* AMD Read Mode */
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-
-static flash_info_t *flash_get_info(ulong base) {
- int i;
- flash_info_t *info;
-
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
- info = &flash_info[i];
- if ((info->size) && (info->start[0] <= base)
- && (base <= info->start[0] + info->size - 1)) {
- break;
- }
- }
- return (i == CONFIG_SYS_MAX_FLASH_BANKS ? 0 : info);
-}
-
-/*-----------------------------------------------------------------------
- */
-
-void flash_print_info(flash_info_t * info) {
- int i;
- char *fmt;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD:
- printf("AMD ");
- break;
- default:
- printf("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AMLV256U:
- fmt = "29LV256M (256 Mbit)\n";
- break;
- default:
- fmt = "Unknown Chip Type\n";
- break;
- }
-
- printf(fmt);
- printf(" Size: %ld MB in %d Sectors\n", info->size >> 20,
- info->sector_count);
- printf(" Sector Start Addresses:");
-
- for (i = 0; i < info->sector_count; ++i) {
- ulong size;
- int erased;
- ulong *flash = (unsigned long *)info->start[i];
-
- if ((i % 5) == 0) {
- printf("\n ");
- }
-
- /*
- * Check if whole sector is erased
- */
- size =
- (i !=
- (info->sector_count - 1)) ? (info->start[i + 1] -
- info->start[i]) >> 2 : (info->
- start
- [0] +
- info->
- size -
- info->
- start
- [i])
- >> 2;
-
- for (flash = (unsigned long *)info->start[i], erased = 1;
- (flash != (unsigned long *)info->start[i] + size)
- && erased; flash++) {
- erased = *flash == ~0x0UL;
- }
- printf(" %08lX %s %s", info->start[i], erased ? "E" : " ",
- info->protect[i] ? "(RO)" : " ");
- }
-
- printf("\n");
-}
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-ulong flash_get_size(FPWV * addr, flash_info_t * info) {
- int i;
-
- /* Write auto select command: read Manufacturer ID */
- /* Write auto select command sequence and test FLASH answer */
- addr[FLASH_CYCLE1] = (FPW) 0x00AA00AA; /* for AMD, Intel ignores this */
- addr[FLASH_CYCLE2] = (FPW) 0x00550055; /* for AMD, Intel ignores this */
- addr[FLASH_CYCLE1] = (FPW) 0x00900090; /* selects Intel or AMD */
-
- /* The manufacturer codes are only 1 byte, so just use 1 byte. */
- /* This works for any bus width and any FLASH device width. */
- udelay(100);
- switch (addr[FLASH_ID1] & 0x00ff) {
- case (uchar) AMD_MANUFACT:
- info->flash_id = FLASH_MAN_AMD;
- break;
- default:
- printf("unknown vendor=%x ", addr[FLASH_ID1] & 0xff);
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- break;
- }
-
- /* Check 16 bits or 32 bits of ID so work on 32 or 16 bit bus. */
- if (info->flash_id != FLASH_UNKNOWN) {
- switch ((FPW) addr[FLASH_ID2]) {
- case (FPW) AMD_ID_MIRROR:
- /* MIRROR BIT FLASH, read more ID bytes */
- if ((FPW) addr[FLASH_ID3] == (FPW) AMD_ID_LV256U_2
- && (FPW) addr[FLASH_ID4] == (FPW) AMD_ID_LV256U_3) {
- /* attention: only the first 16 MB will be used in u-boot */
- info->flash_id += FLASH_AMLV256U;
- info->sector_count = 512;
- info->size = 0x02000000;
- for (i = 0; i < info->sector_count; i++) {
- info->start[i] =
- (ulong) addr + 0x10000 * i;
- }
- break;
- }
- /* fall thru to here ! */
- default:
- printf("unknown AMD device=%x %x %x",
- (FPW) addr[FLASH_ID2], (FPW) addr[FLASH_ID3],
- (FPW) addr[FLASH_ID4]);
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0x800000;
- break;
- }
-
- /* Put FLASH back in read mode */
- flash_reset(info);
- }
- return (info->size);
-}
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase(flash_info_t * info, int s_first, int s_last) {
- FPWV *addr;
- int flag, prot, sect;
- int intel = (info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL;
- ulong start, now, last;
- int rcode = 0;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf("- missing\n");
- } else {
- printf("- no sectors to erase\n");
- }
- return 1;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AMLV256U:
- break;
- case FLASH_UNKNOWN:
- default:
- printf("Can't erase unknown flash type %08lx - aborted\n",
- info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf("\n");
- }
-
- last = get_timer(0);
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last && rcode == 0; sect++) {
- if (info->protect[sect] != 0) { /* protected, skip it */
- continue;
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr = (FPWV *) (info->start[sect]);
- if (intel) {
- *addr = (FPW) 0x00500050; /* clear status register */
- *addr = (FPW) 0x00200020; /* erase setup */
- *addr = (FPW) 0x00D000D0; /* erase confirm */
- } else {
- /* must be AMD style if not Intel */
- FPWV *base; /* first address in bank */
-
- base = (FPWV *) (info->start[0]);
- base[FLASH_CYCLE1] = (FPW) 0x00AA00AA; /* unlock */
- base[FLASH_CYCLE2] = (FPW) 0x00550055; /* unlock */
- base[FLASH_CYCLE1] = (FPW) 0x00800080; /* erase mode */
- base[FLASH_CYCLE1] = (FPW) 0x00AA00AA; /* unlock */
- base[FLASH_CYCLE2] = (FPW) 0x00550055; /* unlock */
- *addr = (FPW) 0x00300030; /* erase sector */
- }
-
- /* re-enable interrupts if necessary */
- if (flag) {
- enable_interrupts();
- }
- start = get_timer(0);
-
- /* wait at least 50us for AMD, 80us for Intel. */
- /* Let's wait 1 ms. */
- udelay(1000);
-
- while ((*addr & (FPW) 0x00800080) != (FPW) 0x00800080) {
- if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf("Timeout\n");
- if (intel) {
- /* suspend erase */
- *addr = (FPW) 0x00B000B0;
- }
- flash_reset(info); /* reset to read mode */
- rcode = 1; /* failed */
- break;
- }
- /* show that we're waiting */
- if ((get_timer(last)) > CONFIG_SYS_HZ) {
- /* every second */
- putc('.');
- last = get_timer(0);
- }
- }
- /* show that we're waiting */
- if ((get_timer(last)) > CONFIG_SYS_HZ) {
- /* every second */
- putc('.');
- last = get_timer(0);
- }
- flash_reset(info); /* reset to read mode */
- }
- printf(" done\n");
- return (rcode);
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-int write_buff(flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- FPW data = 0; /* 16 or 32 bit word, matches flash bus width on MPC8XX */
- int bytes; /* number of bytes to program in current word */
- int left; /* number of bytes left to program */
- int i, res;
-
- for (left = cnt, res = 0;
- left > 0 && res == 0;
- addr += sizeof(data), left -= sizeof(data) - bytes) {
-
- bytes = addr & (sizeof(data) - 1);
- addr &= ~(sizeof(data) - 1);
-
- /* combine source and destination data so can program
- * an entire word of 16 or 32 bits
- */
- for (i = 0; i < sizeof(data); i++) {
- data <<= 8;
- if (i < bytes || i - bytes >= left)
- data += *((uchar *) addr + i);
- else
- data += *src++;
- }
-
- /* write one word to the flash */
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD:
- res = write_word_amd(info, (FPWV *) addr, data);
- break;
- default:
- /* unknown flash type, error! */
- printf("missing or unknown FLASH type\n");
- res = 1; /* not really a timeout, but gives error */
- break;
- }
- }
- return (res);
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash for AMD FLASH
- * A word is 16 or 32 bits, whichever the bus width of the flash bank
- * (not an individual chip) is.
- *
- * returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word_amd(flash_info_t * info, FPWV * dest, FPW data) {
- ulong start;
- int flag;
- int res = 0; /* result, assume success */
- FPWV *base; /* first address in flash bank */
-
- /* Check if Flash is (sufficiently) erased */
- if ((*dest & data) != data) {
- return (2);
- }
-
- base = (FPWV *) (info->start[0]);
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- base[FLASH_CYCLE1] = (FPW) 0x00AA00AA; /* unlock */
- base[FLASH_CYCLE2] = (FPW) 0x00550055; /* unlock */
- base[FLASH_CYCLE1] = (FPW) 0x00A000A0; /* selects program mode */
-
- *dest = data; /* start programming the data */
-
- /* re-enable interrupts if necessary */
- if (flag) {
- enable_interrupts();
- }
- start = get_timer(0);
-
- /* data polling for D7 */
- while (res == 0
- && (*dest & (FPW) 0x00800080) != (data & (FPW) 0x00800080)) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- *dest = (FPW) 0x00F000F0; /* reset bank */
- res = 1;
- }
- }
- return (res);
-}
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#define SDRAM_DDR 1 /* is DDR */
-
-/* Settings for XLB = 132 MHz */
-#define SDRAM_MODE 0x018D0000
-#define SDRAM_EMODE 0x40090000
-#define SDRAM_CONTROL 0x705f0f00
-#define SDRAM_CONFIG1 0x73722930
-#define SDRAM_CONFIG2 0x47770000
-#define SDRAM_TAPDELAY 0x10000000
+++ /dev/null
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * pf5200.c - main board support/init for the esd pf5200.
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-#include <pci.h>
-#include <command.h>
-#include <netdev.h>
-
-#include "mt46v16m16-75.h"
-
-void init_power_switch(void);
-
-static void sdram_start(int hi_addr)
-{
- long hi_addr_bit = hi_addr ? 0x01000000 : 0;
-
- /* unlock mode register */
- *(vu_long *) MPC5XXX_SDRAM_CTRL =
- SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* precharge all banks */
- *(vu_long *) MPC5XXX_SDRAM_CTRL =
- SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* set mode register: extended mode */
- *(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
- __asm__ volatile ("sync");
-
- /* set mode register: reset DLL */
- *(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
- __asm__ volatile ("sync");
-
- /* precharge all banks */
- *(vu_long *) MPC5XXX_SDRAM_CTRL =
- SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* auto refresh */
- *(vu_long *) MPC5XXX_SDRAM_CTRL =
- SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* set mode register */
- *(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE;
- __asm__ volatile ("sync");
-
- /* normal operation */
- *(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
- __asm__ volatile ("sync");
-}
-
-/*
- * ATTENTION: Although partially referenced initdram does NOT make real use
- * use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE
- * is something else than 0x00000000.
- */
-
-phys_size_t initdram(int board_type)
-{
- ulong dramsize = 0;
- ulong test1, test2;
-
- /* setup SDRAM chip selects */
- *(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0x0000001e; /* 2G at 0x0 */
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x80000000; /* disabled */
- __asm__ volatile ("sync");
-
- /* setup config registers */
- *(vu_long *) MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
- *(vu_long *) MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
- __asm__ volatile ("sync");
-
- /* set tap delay */
- *(vu_long *) MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
- __asm__ volatile ("sync");
-
- /* find RAM size using SDRAM CS0 only */
- sdram_start(0);
- test1 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x80000000);
- sdram_start(1);
- test2 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x80000000);
-
- if (test1 > test2) {
- sdram_start(0);
- dramsize = test1;
- } else {
- dramsize = test2;
- }
-
- /* memory smaller than 1MB is impossible */
- if (dramsize < (1 << 20)) {
- dramsize = 0;
- }
-
- /* set SDRAM CS0 size according to the amount of RAM found */
- if (dramsize > 0) {
- *(vu_long *) MPC5XXX_SDRAM_CS0CFG =
- 0x13 + __builtin_ffs(dramsize >> 20) - 1;
- /* let SDRAM CS1 start right after CS0 */
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e; /* 2G */
- } else {
-#if 0
- *(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
- /* let SDRAM CS1 start right after CS0 */
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e; /* 2G */
-#else
- *(vu_long *) MPC5XXX_SDRAM_CS0CFG =
- 0x13 + __builtin_ffs(0x08000000 >> 20) - 1;
- /* let SDRAM CS1 start right after CS0 */
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x08000000 + 0x0000001e; /* 2G */
-#endif
- }
-
-#if 0
- /* find RAM size using SDRAM CS1 only */
- sdram_start(0);
- get_ram_size((ulong *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
- sdram_start(1);
- get_ram_size((ulong *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
- sdram_start(0);
-#endif
- /* set SDRAM CS1 size according to the amount of RAM found */
-
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
-
- init_power_switch();
- return (dramsize);
-}
-
-int checkboard(void)
-{
- puts("Board: esd ParaFinder (pf5200)\n");
- return 0;
-}
-
-void flash_preinit(void)
-{
- /*
- * Now, when we are in RAM, enable flash write
- * access for detection process.
- * Note that CS_BOOT cannot be cleared when
- * executing in flash.
- */
- *(vu_long *) MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
-}
-
-void flash_afterinit(ulong size)
-{
- if (size == 0x02000000) {
- /* adjust mapping */
- *(vu_long *) MPC5XXX_BOOTCS_START =
- *(vu_long *) MPC5XXX_CS0_START =
- START_REG(CONFIG_SYS_BOOTCS_START | size);
- *(vu_long *) MPC5XXX_BOOTCS_STOP =
- *(vu_long *) MPC5XXX_CS0_STOP =
- STOP_REG(CONFIG_SYS_BOOTCS_START | size, size);
- }
-}
-
-#ifdef CONFIG_PCI
-static struct pci_controller hose;
-
-extern void pci_mpc5xxx_init(struct pci_controller *);
-
-void pci_init_board(void) {
- pci_mpc5xxx_init(&hose);
-}
-#endif
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
-
-void init_ide_reset(void)
-{
- debug("init_ide_reset\n");
-
- /* Configure PSC1_4 as GPIO output for ATA reset */
- *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
- *(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
-}
-
-void ide_set_reset(int idereset)
-{
- debug("ide_reset(%d)\n", idereset);
-
- if (idereset) {
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
- } else {
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
- }
-}
-#endif
-
-#define MPC5XXX_SIMPLEIO_GPIO_ENABLE (MPC5XXX_GPIO + 0x0004)
-#define MPC5XXX_SIMPLEIO_GPIO_DIR (MPC5XXX_GPIO + 0x000C)
-#define MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT (MPC5XXX_GPIO + 0x0010)
-#define MPC5XXX_SIMPLEIO_GPIO_DATA_INPUT (MPC5XXX_GPIO + 0x0014)
-
-#define MPC5XXX_INTERRUPT_GPIO_ENABLE (MPC5XXX_GPIO + 0x0020)
-#define MPC5XXX_INTERRUPT_GPIO_DIR (MPC5XXX_GPIO + 0x0028)
-#define MPC5XXX_INTERRUPT_GPIO_DATA_OUTPUT (MPC5XXX_GPIO + 0x002C)
-#define MPC5XXX_INTERRUPT_GPIO_STATUS (MPC5XXX_GPIO + 0x003C)
-
-#define GPIO_WU6 0x40000000UL
-#define GPIO_USB0 0x00010000UL
-#define GPIO_USB9 0x08000000UL
-#define GPIO_USB9S 0x00080000UL
-
-void init_power_switch(void)
-{
- debug("init_power_switch\n");
-
- /* Configure GPIO_WU6 as GPIO output for ATA reset */
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_WU6;
- *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_WU6;
- *(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_WU6;
- __asm__ volatile ("sync");
-
- *(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT &= ~GPIO_USB0;
- *(vu_long *) MPC5XXX_SIMPLEIO_GPIO_ENABLE |= GPIO_USB0;
- *(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DIR |= GPIO_USB0;
- __asm__ volatile ("sync");
-
- *(vu_long *) MPC5XXX_INTERRUPT_GPIO_DATA_OUTPUT &= ~GPIO_USB9;
- *(vu_long *) MPC5XXX_INTERRUPT_GPIO_ENABLE &= ~GPIO_USB9;
- __asm__ volatile ("sync");
-
- if ((*(vu_long *) MPC5XXX_INTERRUPT_GPIO_STATUS & GPIO_USB9S) == 0) {
- *(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT |= GPIO_USB0;
- __asm__ volatile ("sync");
- }
- *(vu_char *) CONFIG_SYS_CS1_START = 0x02; /* Red Power LED on */
- __asm__ volatile ("sync");
-
- *(vu_char *) (CONFIG_SYS_CS1_START + 1) = 0x02; /* Disable driver for KB11 */
- __asm__ volatile ("sync");
-}
-
-int board_eth_init(bd_t *bis)
-{
- return pci_eth_init(bis);
-}
-
-void power_set_reset(int power)
-{
- debug("ide_set_reset(%d)\n", power);
-
- if (power) {
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_WU6;
- *(vu_long *) MPC5XXX_INTERRUPT_GPIO_DATA_OUTPUT &= ~GPIO_USB9;
- } else {
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_WU6;
- if ((*(vu_long *) MPC5XXX_INTERRUPT_GPIO_STATUS & GPIO_USB9S) ==
- 0) {
- *(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT |=
- GPIO_USB0;
- }
-
- }
-}
-
-int do_poweroff(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
- power_set_reset(1);
- return (0);
-}
-
-U_BOOT_CMD(poweroff, 1, 1, do_poweroff, "Switch off power", "");
-
-int phypower(int flag)
-{
- u32 addr;
- vu_long *reg;
- int status;
- pci_dev_t dev;
-
- dev = PCI_BDF(0, 0x18, 0);
- status = pci_read_config_dword(dev, PCI_BASE_ADDRESS_1, &addr);
- if (status == 0) {
- reg = (vu_long *) (addr + 0x00000040);
- *reg |= 0x40000000;
- __asm__ volatile ("sync");
-
- reg = (vu_long *) (addr + 0x001000c);
- *reg |= 0x20000000;
- __asm__ volatile ("sync");
-
- reg = (vu_long *) (addr + 0x0010004);
- if (flag != 0) {
- *reg &= ~0x20000000;
- } else {
- *reg |= 0x20000000;
- }
- __asm__ volatile ("sync");
- }
- return (status);
-}
-
-int do_phypower(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
- if (argv[1][0] == '0')
- (void)phypower(0);
- else
- (void)phypower(1);
-
- return (0);
-}
-
-U_BOOT_CMD(phypower, 2, 2, do_phypower,
- "Switch power of ethernet phy", "");
-
-int do_writepci(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
- unsigned int addr;
- unsigned int size;
- int i;
- volatile unsigned long *ptr;
-
- addr = simple_strtol(argv[1], NULL, 16);
- size = simple_strtol(argv[2], NULL, 16);
-
- printf("\nWriting at addr %08x, size %08x.\n", addr, size);
-
- while (1) {
- ptr = (volatile unsigned long *)addr;
- for (i = 0; i < (size >> 2); i++) {
- *ptr++ = i;
- }
-
- /* Abort if ctrl-c was pressed */
- if (ctrlc()) {
- puts("\nAbort\n");
- return 0;
- }
- putc('.');
- }
- return 0;
-}
-
-U_BOOT_CMD(writepci, 3, 1, do_writepci,
- "Write some data to pcibus",
- "<addr> <size>\n"
- ""
-);
+++ /dev/null
-if TARGET_ICECUBE
-
-config SYS_BOARD
- default "icecube"
-
-config SYS_CONFIG_NAME
- default "IceCube"
-
-endif
+++ /dev/null
-ICECUBE BOARD
-M: Wolfgang Denk <wd@denx.de>
-S: Maintained
-F: board/icecube/
-F: include/configs/IceCube.h
-F: configs/icecube_5200_defconfig
-
-ICECUBE_5200_DDR BOARD
-#M: -
-S: Maintained
-F: configs/icecube_5200_DDR_defconfig
-F: configs/icecube_5200_DDR_LOWBOOT_defconfig
-F: configs/icecube_5200_DDR_LOWBOOT08_defconfig
-F: configs/icecube_5200_LOWBOOT_defconfig
-F: configs/icecube_5200_LOWBOOT08_defconfig
-F: configs/Lite5200_defconfig
-F: configs/Lite5200_LOWBOOT_defconfig
-F: configs/Lite5200_LOWBOOT08_defconfig
-F: configs/lite5200b_defconfig
-F: configs/lite5200b_LOWBOOT_defconfig
-F: configs/lite5200b_PM_defconfig
+++ /dev/null
-#
-# (C) Copyright 2003-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := icecube.o flash.o
+++ /dev/null
----------------------------------------------------------------------------
-Build target Flash address | BDI "go" command | Reset Vector
----------------------------------------------------------------------------
-Lite5200 0xFFF00000 | 0xFFF00100 | 0xFFF00100
-Lite5200_LOWBOOT 0xFF000000 | 0xFF000100 | 0x00000100
-Lite5200_LOWBOOT08 0xFF800000 | 0xFF800100 | 0x00000100
-icecube_5200 0xFFF00000 | 0xFFF00100 | 0xFFF00100
-icecube_5200_LOWBOOT 0xFF000000 | 0xFF000100 | 0x00000100
-icecube_5200_LOWBOOT08 0xFF800000 | 0xFF800100 | 0x00000100
-icecube_5200_DDR 0xFFF00000 | 0xFFF00100 | 0xFFF00100
-icecube_5200_DDR_LOWBOOT 0xFF800000 | 0xFF800100 | 0x00000100
-icecube_5200_DDR_LOWBOOT08 0xFF800000 | 0xFF800100 | 0x00000100
----------------------------------------------------------------------------
+++ /dev/null
-Lite5200B wakeup from low-power mode (CONFIG_LITE5200B_PM)
-----------------------------------------------------------
-
-Low-power mode as described in Lite5200B User's Manual, means that
-with support of MC68HLC908QT1 microcontroller (refered to as QT),
-everything but the SDRAM can be powered down. This brings
-maximum power saving, while one can still restore previous state
-quickly.
-
-Quick overview where U-Boot comes into the picture:
-- OS saves device states
-- OS saves wakeup handler address to physical 0x0, puts SDRAM into
- self-refresh and signals to QT, it should power down the board
-- / board is sleeping here /
-- someone presses SW4 (connected to QT)
-- U-Boot checks PSC2_4 pin, if QT drives it down, then we woke up,
- so get SDRAM out of self-refresh and transfer control to OS
- wakeup handler
-- OS restores device states
-
-This was tested on Linux with USB and Ethernet in use. Adding
-support for other devices is an OS issue.
+++ /dev/null
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-#ifndef CONFIG_FLASH_CFI_DRIVER
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-/* NOTE - CONFIG_FLASH_16BIT means the CPU interface is 16-bit, it
- * has nothing to do with the flash chip being 8-bit or 16-bit.
- */
-#ifdef CONFIG_FLASH_16BIT
-typedef unsigned short FLASH_PORT_WIDTH;
-typedef volatile unsigned short FLASH_PORT_WIDTHV;
-#define FLASH_ID_MASK 0xFFFF
-#else
-typedef unsigned char FLASH_PORT_WIDTH;
-typedef volatile unsigned char FLASH_PORT_WIDTHV;
-#define FLASH_ID_MASK 0xFF
-#endif
-
-#define FPW FLASH_PORT_WIDTH
-#define FPWV FLASH_PORT_WIDTHV
-
-#define ORMASK(size) ((-size) & OR_AM_MSK)
-
-#define FLASH_CYCLE1 0x0555
-#define FLASH_CYCLE2 0x02aa
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size(FPWV *addr, flash_info_t *info);
-static void flash_reset(flash_info_t *info);
-static int write_word_amd(flash_info_t *info, FPWV *dest, FPW data);
-static flash_info_t *flash_get_info(ulong base);
-
-/*-----------------------------------------------------------------------
- * flash_init()
- *
- * sets up flash_info and returns size of FLASH (bytes)
- */
-unsigned long flash_init (void)
-{
- unsigned long size = 0;
- int i;
- extern void flash_preinit(void);
- extern void flash_afterinit(ulong);
- ulong flashbase = CONFIG_SYS_FLASH_BASE;
-
- flash_preinit();
-
- /* Init: no FLASHes known */
- for (i=0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- memset(&flash_info[i], 0, sizeof(flash_info_t));
-
- flash_info[i].size =
- flash_get_size((FPW *)flashbase, &flash_info[i]);
-
- size += flash_info[i].size;
- flashbase += 0x800000;
- }
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1,
- flash_get_info(CONFIG_SYS_MONITOR_BASE));
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR+CONFIG_ENV_SIZE-1,
- flash_get_info(CONFIG_ENV_ADDR));
-#endif
-
-
- flash_afterinit(size);
- return size ? size : 1;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_reset(flash_info_t *info)
-{
- FPWV *base = (FPWV *)(info->start[0]);
-
- /* Put FLASH back in read mode */
- if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL)
- *base = (FPW)0x00FF00FF; /* Intel Read Mode */
- else if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_AMD)
- *base = (FPW)0x00F000F0; /* AMD Read Mode */
-}
-
-/*-----------------------------------------------------------------------
- */
-
-static flash_info_t *flash_get_info(ulong base)
-{
- int i;
- flash_info_t * info;
-
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i ++) {
- info = & flash_info[i];
- if (info->size &&
- info->start[0] <= base && base <= info->start[0] + info->size - 1)
- break;
- }
-
- return i == CONFIG_SYS_MAX_FLASH_BANKS ? 0 : info;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-void flash_print_info (flash_info_t *info)
-{
- int i;
- uchar *boottype;
- uchar *bootletter;
- char *fmt;
- uchar botbootletter[] = "B";
- uchar topbootletter[] = "T";
- uchar botboottype[] = "bottom boot sector";
- uchar topboottype[] = "top boot sector";
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD: printf ("AMD "); break;
- case FLASH_MAN_BM: printf ("BRIGHT MICRO "); break;
- case FLASH_MAN_FUJ: printf ("FUJITSU "); break;
- case FLASH_MAN_SST: printf ("SST "); break;
- case FLASH_MAN_STM: printf ("STM "); break;
- case FLASH_MAN_INTEL: printf ("INTEL "); break;
- default: printf ("Unknown Vendor "); break;
- }
-
- /* check for top or bottom boot, if it applies */
- if (info->flash_id & FLASH_BTYPE) {
- boottype = botboottype;
- bootletter = botbootletter;
- }
- else {
- boottype = topboottype;
- bootletter = topbootletter;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AMDLV065D:
- fmt = "29LV065 (64 Mbit, uniform sectors)\n";
- break;
- default:
- fmt = "Unknown Chip Type\n";
- break;
- }
-
- printf (fmt, bootletter, boottype);
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20,
- info->sector_count);
-
- printf (" Sector Start Addresses:");
-
- for (i=0; i<info->sector_count; ++i) {
- if ((i % 5) == 0) {
- printf ("\n ");
- }
-
- printf (" %08lX%s", info->start[i],
- info->protect[i] ? " (RO)" : " ");
- }
-
- printf ("\n");
-}
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-ulong flash_get_size (FPWV *addr, flash_info_t *info)
-{
- int i;
- FPWV* addr2;
-
- /* Write auto select command: read Manufacturer ID */
- /* Write auto select command sequence and test FLASH answer */
- addr[FLASH_CYCLE1] = (FPW)0x00AA00AA; /* for AMD, Intel ignores this */
- addr[FLASH_CYCLE2] = (FPW)0x00550055; /* for AMD, Intel ignores this */
- addr[FLASH_CYCLE1] = (FPW)0x00900090; /* selects Intel or AMD */
-
- /* The manufacturer codes are only 1 byte, so just use 1 byte.
- * This works for any bus width and any FLASH device width.
- */
- udelay(100);
- switch (addr[0] & 0xff) {
-
- case (uchar)AMD_MANUFACT:
- info->flash_id = FLASH_MAN_AMD;
- break;
-
- case (uchar)INTEL_MANUFACT:
- info->flash_id = FLASH_MAN_INTEL;
- break;
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- break;
- }
-
- /* Check 16 bits or 32 bits of ID so work on 32 or 16 bit bus. */
- if (info->flash_id != FLASH_UNKNOWN) switch ((FPW)addr[1]) {
-
- case (FPW)AMD_ID_LV065D:
- info->flash_id += FLASH_AMDLV065D;
- info->sector_count = 128;
- info->size = 0x00800000;
- for( i = 0; i < info->sector_count; i++ )
- info->start[i] = (ulong)addr + (i * 0x10000);
- break; /* => 8 or 16 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- return (0); /* => no or unknown flash */
- }
-
- /* test for real flash at bank 1 */
- addr2 = (FPW *)((ulong)addr | 0x800000);
- if (addr2 != addr &&
- ((addr2[0] & 0xff) == (addr[0] & 0xff)) && ((FPW)addr2[1] == (FPW)addr[1])) {
- /* Seems 2 banks are the same space (8Mb chip is installed,
- * J24 in default position (CS0)). Disable this (first) bank.
- */
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- }
- /* Put FLASH back in read mode */
- flash_reset(info);
-
- return (info->size);
-}
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
- FPWV *addr;
- int flag, prot, sect;
- int intel = (info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL;
- ulong start, now, last;
- int rcode = 0;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AMDLV065D:
- break;
- case FLASH_UNKNOWN:
- default:
- printf ("Can't erase unknown flash type %08lx - aborted\n",
- info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect=s_first; sect<=s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- last = get_timer(0);
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect<=s_last && rcode == 0; sect++) {
-
- if (info->protect[sect] != 0) /* protected, skip it */
- continue;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr = (FPWV *)(info->start[sect]);
- if (intel) {
- *addr = (FPW)0x00500050; /* clear status register */
- *addr = (FPW)0x00200020; /* erase setup */
- *addr = (FPW)0x00D000D0; /* erase confirm */
- }
- else {
- /* must be AMD style if not Intel */
- FPWV *base; /* first address in bank */
-
- base = (FPWV *)(info->start[0]);
- base[FLASH_CYCLE1] = (FPW)0x00AA00AA; /* unlock */
- base[FLASH_CYCLE2] = (FPW)0x00550055; /* unlock */
- base[FLASH_CYCLE1] = (FPW)0x00800080; /* erase mode */
- base[FLASH_CYCLE1] = (FPW)0x00AA00AA; /* unlock */
- base[FLASH_CYCLE2] = (FPW)0x00550055; /* unlock */
- *addr = (FPW)0x00300030; /* erase sector */
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- start = get_timer(0);
-
- /* wait at least 50us for AMD, 80us for Intel.
- * Let's wait 1 ms.
- */
- udelay (1000);
-
- while ((*addr & (FPW)0x00800080) != (FPW)0x00800080) {
- if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
-
- if (intel) {
- /* suspend erase */
- *addr = (FPW)0x00B000B0;
- }
-
- flash_reset(info); /* reset to read mode */
- rcode = 1; /* failed */
- break;
- }
-
- /* show that we're waiting */
- if ((get_timer(last)) > CONFIG_SYS_HZ) {/* every second */
- putc ('.');
- last = get_timer(0);
- }
- }
-
- /* show that we're waiting */
- if ((get_timer(last)) > CONFIG_SYS_HZ) { /* every second */
- putc ('.');
- last = get_timer(0);
- }
-
- flash_reset(info); /* reset to read mode */
- }
-
- printf (" done\n");
- return rcode;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- FPW data = 0; /* 16 or 32 bit word, matches flash bus width on MPC8XX */
- int bytes; /* number of bytes to program in current word */
- int left; /* number of bytes left to program */
- int i, res;
-
- for (left = cnt, res = 0;
- left > 0 && res == 0;
- addr += sizeof(data), left -= sizeof(data) - bytes) {
-
- bytes = addr & (sizeof(data) - 1);
- addr &= ~(sizeof(data) - 1);
-
- /* combine source and destination data so can program
- * an entire word of 16 or 32 bits
- */
- for (i = 0; i < sizeof(data); i++) {
- data <<= 8;
- if (i < bytes || i - bytes >= left )
- data += *((uchar *)addr + i);
- else
- data += *src++;
- }
-
- /* write one word to the flash */
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD:
- res = write_word_amd(info, (FPWV *)addr, data);
- break;
- default:
- /* unknown flash type, error! */
- printf ("missing or unknown FLASH type\n");
- res = 1; /* not really a timeout, but gives error */
- break;
- }
- }
-
- return (res);
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash for AMD FLASH
- * A word is 16 or 32 bits, whichever the bus width of the flash bank
- * (not an individual chip) is.
- *
- * returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word_amd (flash_info_t *info, FPWV *dest, FPW data)
-{
- ulong start;
- int flag;
- int res = 0; /* result, assume success */
- FPWV *base; /* first address in flash bank */
-
- /* Check if Flash is (sufficiently) erased */
- if ((*dest & data) != data) {
- return (2);
- }
-
-
- base = (FPWV *)(info->start[0]);
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- base[FLASH_CYCLE1] = (FPW)0x00AA00AA; /* unlock */
- base[FLASH_CYCLE2] = (FPW)0x00550055; /* unlock */
- base[FLASH_CYCLE1] = (FPW)0x00A000A0; /* selects program mode */
-
- *dest = data; /* start programming the data */
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- start = get_timer (0);
-
- /* data polling for D7 */
- while (res == 0 && (*dest & (FPW)0x00800080) != (data & (FPW)0x00800080)) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- *dest = (FPW)0x00F000F0; /* reset bank */
- res = 1;
- }
- }
-
- return (res);
-}
-#endif /*CONFIG_FLASH_CFI_DRIVER*/
+++ /dev/null
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-#include <pci.h>
-#include <asm/processor.h>
-#include <libfdt.h>
-#include <netdev.h>
-
-#if defined(CONFIG_LITE5200B)
-#include "mt46v32m16.h"
-#else
-# if defined(CONFIG_MPC5200_DDR)
-# include "mt46v16m16-75.h"
-# else
-#include "mt48lc16m16a2-75.h"
-# endif
-#endif
-
-#ifdef CONFIG_LITE5200B_PM
-/* u-boot part of low-power mode implementation */
-#define SAVED_ADDR (*(void **)0x00000000)
-#define PSC2_4 0x02
-
-void lite5200b_wakeup(void)
-{
- unsigned char wakeup_pin;
- void (*linux_wakeup)(void);
-
- /* check PSC2_4, if it's down "QT" is signaling we have a wakeup
- * from low power mode */
- *(vu_char *)MPC5XXX_WU_GPIO_ENABLE = PSC2_4;
- __asm__ volatile ("sync");
-
- wakeup_pin = *(vu_char *)MPC5XXX_WU_GPIO_DATA_I;
- if (wakeup_pin & PSC2_4)
- return;
-
- /* acknowledge to "QT"
- * by holding pin at 1 for 10 uS */
- *(vu_char *)MPC5XXX_WU_GPIO_DIR = PSC2_4;
- __asm__ volatile ("sync");
- *(vu_char *)MPC5XXX_WU_GPIO_DATA_O = PSC2_4;
- __asm__ volatile ("sync");
- udelay(10);
-
- /* put ram out of self-refresh */
- *(vu_long *)MPC5XXX_SDRAM_CTRL |= 0x80000000; /* mode_en */
- __asm__ volatile ("sync");
- *(vu_long *)MPC5XXX_SDRAM_CTRL |= 0x50000000; /* cke ref_en */
- __asm__ volatile ("sync");
- *(vu_long *)MPC5XXX_SDRAM_CTRL &= ~0x80000000; /* !mode_en */
- __asm__ volatile ("sync");
- udelay(10); /* wait a bit */
-
- /* jump back to linux kernel code */
- linux_wakeup = SAVED_ADDR;
- printf("\n\nLooks like we just woke, transferring control to 0x%08lx\n",
- (unsigned long)linux_wakeup);
- linux_wakeup();
-}
-#else
-#define lite5200b_wakeup()
-#endif
-
-#ifndef CONFIG_SYS_RAMBOOT
-static void sdram_start (int hi_addr)
-{
- long hi_addr_bit = hi_addr ? 0x01000000 : 0;
-
- /* unlock mode register */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* precharge all banks */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
- __asm__ volatile ("sync");
-
-#if SDRAM_DDR
- /* set mode register: extended mode */
- *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
- __asm__ volatile ("sync");
-
- /* set mode register: reset DLL */
- *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
- __asm__ volatile ("sync");
-#endif
-
- /* precharge all banks */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* auto refresh */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* set mode register */
- *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE;
- __asm__ volatile ("sync");
-
- /* normal operation */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
- __asm__ volatile ("sync");
-}
-#endif
-
-/*
- * ATTENTION: Although partially referenced initdram does NOT make real use
- * use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE
- * is something else than 0x00000000.
- */
-
-phys_size_t initdram (int board_type)
-{
- ulong dramsize = 0;
- ulong dramsize2 = 0;
- uint svr, pvr;
-
-#ifndef CONFIG_SYS_RAMBOOT
- ulong test1, test2;
-
- /* setup SDRAM chip selects */
- *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001e;/* 2G at 0x0 */
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x80000000;/* disabled */
- __asm__ volatile ("sync");
-
- /* setup config registers */
- *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
- *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
- __asm__ volatile ("sync");
-
-#if SDRAM_DDR
- /* set tap delay */
- *(vu_long *)MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
- __asm__ volatile ("sync");
-#endif
-
- /* find RAM size using SDRAM CS0 only */
- sdram_start(0);
- test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
- sdram_start(1);
- test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
- if (test1 > test2) {
- sdram_start(0);
- dramsize = test1;
- } else {
- dramsize = test2;
- }
-
- /* memory smaller than 1MB is impossible */
- if (dramsize < (1 << 20)) {
- dramsize = 0;
- }
-
- /* set SDRAM CS0 size according to the amount of RAM found */
- if (dramsize > 0) {
- *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 + __builtin_ffs(dramsize >> 20) - 1;
- } else {
- *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
- }
-
- /* let SDRAM CS1 start right after CS0 */
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;/* 2G */
-
- /* find RAM size using SDRAM CS1 only */
- if (!dramsize)
- sdram_start(0);
- test2 = test1 = get_ram_size((long *)(CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
- if (!dramsize) {
- sdram_start(1);
- test2 = get_ram_size((long *)(CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
- }
- if (test1 > test2) {
- sdram_start(0);
- dramsize2 = test1;
- } else {
- dramsize2 = test2;
- }
-
- /* memory smaller than 1MB is impossible */
- if (dramsize2 < (1 << 20)) {
- dramsize2 = 0;
- }
-
- /* set SDRAM CS1 size according to the amount of RAM found */
- if (dramsize2 > 0) {
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize
- | (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
- } else {
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
- }
-
-#else /* CONFIG_SYS_RAMBOOT */
-
- /* retrieve size of memory connected to SDRAM CS0 */
- dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF;
- if (dramsize >= 0x13) {
- dramsize = (1 << (dramsize - 0x13)) << 20;
- } else {
- dramsize = 0;
- }
-
- /* retrieve size of memory connected to SDRAM CS1 */
- dramsize2 = *(vu_long *)MPC5XXX_SDRAM_CS1CFG & 0xFF;
- if (dramsize2 >= 0x13) {
- dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
- } else {
- dramsize2 = 0;
- }
-
-#endif /* CONFIG_SYS_RAMBOOT */
-
- /*
- * On MPC5200B we need to set the special configuration delay in the
- * DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM
- * Initialization and Configuration", 3.3.1 SDelay--MBAR + 0x0190:
- *
- * "The SDelay should be written to a value of 0x00000004. It is
- * required to account for changes caused by normal wafer processing
- * parameters."
- */
- svr = get_svr();
- pvr = get_pvr();
- if ((SVR_MJREV(svr) >= 2) &&
- (PVR_MAJ(pvr) == 1) && (PVR_MIN(pvr) == 4)) {
-
- *(vu_long *)MPC5XXX_SDRAM_SDELAY = 0x04;
- __asm__ volatile ("sync");
- }
-
- lite5200b_wakeup();
-
- return dramsize + dramsize2;
-}
-
-int checkboard (void)
-{
-#if defined (CONFIG_LITE5200B)
- puts ("Board: Freescale Lite5200B\n");
-#else
- puts ("Board: Motorola MPC5200 (IceCube)\n");
-#endif
- return 0;
-}
-
-void flash_preinit(void)
-{
- /*
- * Now, when we are in RAM, enable flash write
- * access for detection process.
- * Note that CS_BOOT cannot be cleared when
- * executing in flash.
- */
- *(vu_long *)MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
-}
-
-void flash_afterinit(ulong size)
-{
- if (size == 0x800000) { /* adjust mapping */
- *(vu_long *)MPC5XXX_BOOTCS_START = *(vu_long *)MPC5XXX_CS0_START =
- START_REG(CONFIG_SYS_BOOTCS_START | size);
- *(vu_long *)MPC5XXX_BOOTCS_STOP = *(vu_long *)MPC5XXX_CS0_STOP =
- STOP_REG(CONFIG_SYS_BOOTCS_START | size, size);
- }
-}
-
-#ifdef CONFIG_PCI
-static struct pci_controller hose;
-
-extern void pci_mpc5xxx_init(struct pci_controller *);
-
-void pci_init_board(void)
-{
- pci_mpc5xxx_init(&hose);
-}
-#endif
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
-
-void init_ide_reset (void)
-{
- debug ("init_ide_reset\n");
-
- /* Configure PSC1_4 as GPIO output for ATA reset */
- *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
- *(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
- /* Deassert reset */
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
-}
-
-void ide_set_reset (int idereset)
-{
- debug ("ide_reset(%d)\n", idereset);
-
- if (idereset) {
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
- /* Make a delay. MPC5200 spec says 25 usec min */
- udelay(500000);
- } else {
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
- }
-}
-#endif
-
-#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, bd_t *bd)
-{
- ft_cpu_setup(blob, bd);
-
- return 0;
-}
-#endif
-
-int board_eth_init(bd_t *bis)
-{
- cpu_eth_init(bis); /* Built in FEC comes first */
- return pci_eth_init(bis);
-}
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#define SDRAM_DDR 1 /* is DDR */
-
-/* Settings for XLB = 132 MHz */
-#define SDRAM_MODE 0x018D0000
-#define SDRAM_EMODE 0x40090000
-#define SDRAM_CONTROL 0x705f0f00
-#define SDRAM_CONFIG1 0x73722930
-#define SDRAM_CONFIG2 0x47770000
-#define SDRAM_TAPDELAY 0x10000000
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#define SDRAM_DDR 1 /* is DDR */
-
-/* Settings for XLB = 132 MHz */
-#define SDRAM_MODE 0x018D0000
-#define SDRAM_EMODE 0x40090000
-#define SDRAM_CONTROL 0x704f0f00
-#define SDRAM_CONFIG1 0x73722930
-#define SDRAM_CONFIG2 0x47770000
-#define SDRAM_TAPDELAY 0x10000000
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#define SDRAM_DDR 0 /* is SDR */
-
-/* Settings for XLB = 132 MHz */
-#define SDRAM_MODE 0x00CD0000
-#define SDRAM_CONTROL 0x504F0000
-#define SDRAM_CONFIG1 0xD2322800
-#define SDRAM_CONFIG2 0x8AD70000
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFF800000"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_ICECUBE=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFF000000"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_ICECUBE=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_ICECUBE=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_CPCI5200=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFF800000,MPC5200_DDR"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_ICECUBE=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFF800000,MPC5200_DDR"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_ICECUBE=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="MPC5200_DDR"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_ICECUBE=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFF800000"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_ICECUBE=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFF000000"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_ICECUBE=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_ICECUBE=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="MPC5200_DDR,LITE5200B,SYS_TEXT_BASE=0xFF000000"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_ICECUBE=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="MPC5200_DDR,LITE5200B,LITE5200B_PM"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_ICECUBE=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="MPC5200_DDR,LITE5200B"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_ICECUBE=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_MECP5200=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_PF5200=y
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+icecube_5200 powerpc mpc5xxx - - Wolfgang Denk <wd@denx.de>
+Lite5200 powerpc mpc5xxx - -
+cpci5200 powerpc mpc5xxx - - Reinhard Arlt <reinhard.arlt@esd-electronics.com>
+mecp5200 powerpc mpc5xxx - - Reinhard Arlt <reinhard.arlt@esd-electronics.com>
+pf5200 powerpc mpc5xxx - - Reinhard Arlt <reinhard.arlt@esd-electronics.com>
PM520 powerpc mpc5xxx - - Josef Wagner <Wagner@Microsys.de>
Total5200 powerpc mpc5xxx - -
CATcenter powerpc ppc4xx - -
+++ /dev/null
-/*
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */
-#define CONFIG_ICECUBE 1 /* ... on IceCube board */
-
-/*
- * Valid values for CONFIG_SYS_TEXT_BASE are:
- * 0xFFF00000 boot high (standard configuration)
- * 0xFF000000 boot low for 16 MiB boards
- * 0xFF800000 boot low for 8 MiB boards
- * 0x00100000 boot from RAM (for testing only)
- */
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-#endif
-
-#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
-#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-
-/*
- * PCI Mapping:
- * 0x40000000 - 0x4fffffff - PCI Memory
- * 0x50000000 - 0x50ffffff - PCI IO Space
- */
-#define CONFIG_PCI
-
-#if defined(CONFIG_PCI)
-#define CONFIG_PCI_PNP 1
-#define CONFIG_PCI_SCAN_SHOW 1
-#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
-
-#define CONFIG_PCI_MEM_BUS 0x40000000
-#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
-#define CONFIG_PCI_MEM_SIZE 0x10000000
-
-#define CONFIG_PCI_IO_BUS 0x50000000
-#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
-#define CONFIG_PCI_IO_SIZE 0x01000000
-#endif
-
-#define CONFIG_SYS_XLB_PIPELINING 1
-
-#define CONFIG_MII 1
-#define CONFIG_EEPRO100 1
-#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
-#define CONFIG_NS8382X 1
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
-/* USB */
-#define CONFIG_USB_OHCI_NEW
-#define CONFIG_USB_STORAGE
-#define CONFIG_SYS_OHCI_BE_CONTROLLER
-#undef CONFIG_SYS_USB_OHCI_BOARD_INIT
-#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
-#define CONFIG_SYS_USB_OHCI_REGS_BASE MPC5XXX_USB
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME "mpc5200"
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
-
-#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-#define CONFIG_CMD_USB
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#endif
-
-
-#if (CONFIG_SYS_TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
-# define CONFIG_SYS_LOWBOOT 1
-# define CONFIG_SYS_LOWBOOT16 1
-#endif
-#if (CONFIG_SYS_TEXT_BASE == 0xFF800000) /* Boot low with 8 MB Flash */
-#if defined(CONFIG_LITE5200B)
-# error CONFIG_SYS_LOWBOOT08 is incompatible with the Lite5200B
-#else
-# define CONFIG_SYS_LOWBOOT 1
-# define CONFIG_SYS_LOWBOOT08 1
-#endif
-#endif
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_82xx\0" \
- "bootfile=/tftpboot/MPC5200/uImage\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-/*
- * IPB Bus clocking configuration.
- */
-#if defined(CONFIG_LITE5200B)
-#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#else
-#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
-#define OF_CPU "PowerPC,5200@0"
-#define OF_SOC "soc5200@f0000000"
-#define OF_TBCLK (bd->bi_busfreq / 4)
-#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
-
-/*
- * Flash configuration
- */
-#if defined(CONFIG_LITE5200B)
-#define CONFIG_SYS_FLASH_BASE 0xFE000000
-#define CONFIG_SYS_FLASH_SIZE 0x01000000
-#if !defined(CONFIG_SYS_LOWBOOT)
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x01760000 + 0x00800000)
-#else /* CONFIG_SYS_LOWBOOT */
-#if defined(CONFIG_SYS_LOWBOOT08)
-# error CONFIG_SYS_LOWBOOT08 is incompatible with the Lite5200B
-#endif
-#if defined(CONFIG_SYS_LOWBOOT16)
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x01060000)
-#endif
-#endif /* CONFIG_SYS_LOWBOOT */
-#else /* !CONFIG_LITE5200B (IceCube)*/
-#define CONFIG_SYS_FLASH_BASE 0xFF000000
-#define CONFIG_SYS_FLASH_SIZE 0x01000000
-#if !defined(CONFIG_SYS_LOWBOOT)
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00740000 + 0x00800000)
-#else /* CONFIG_SYS_LOWBOOT */
-#if defined(CONFIG_SYS_LOWBOOT08)
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000 + 0x00800000)
-#endif
-#if defined(CONFIG_SYS_LOWBOOT16)
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000)
-#endif
-#endif /* CONFIG_SYS_LOWBOOT */
-#endif /* CONFIG_LITE5200B */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of memory banks */
-
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
-
-#undef CONFIG_FLASH_16BIT /* Flash is 8-bit */
-
-#if defined(CONFIG_LITE5200B)
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_CS1_START,CONFIG_SYS_CS0_START}
-#endif
-
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SIZE 0x10000
-#if defined(CONFIG_LITE5200B)
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#else
-#define CONFIG_ENV_SECT_SIZE 0x10000
-#endif
-#define CONFIG_ENV_OVERWRITE 1
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR 0xF0000000
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
-
-/* Use SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */
-
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT 1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC 1
-#define CONFIG_MPC5xxx_FEC_MII100
-/*
- * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
- */
-/* #define CONFIG_MPC5xxx_FEC_MII10 */
-#define CONFIG_PHY_ADDR 0x00
-
-/*
- * GPIO configuration
- */
-#ifdef CONFIG_MPC5200_DDR
-#define CONFIG_SYS_GPS_PORT_CONFIG 0x90000004
-#else
-#define CONFIG_SYS_GPS_PORT_CONFIG 0x10000004
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL HID0_ICE
-
-#if defined(CONFIG_LITE5200B)
-#define CONFIG_SYS_CS1_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS1_SIZE CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_CS1_CFG 0x00047800
-#define CONFIG_SYS_CS0_START (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE)
-#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_CS0_START
-#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_CFG 0x00047800
-#else /* IceCube aka Lite5200 */
-#ifdef CONFIG_MPC5200_DDR
-
-#define CONFIG_SYS_BOOTCS_START (CONFIG_SYS_CS1_START + CONFIG_SYS_CS1_SIZE)
-#define CONFIG_SYS_BOOTCS_SIZE 0x00800000
-#define CONFIG_SYS_BOOTCS_CFG 0x00047801
-#define CONFIG_SYS_CS1_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS1_SIZE 0x00800000
-#define CONFIG_SYS_CS1_CFG 0x00047800
-
-#else /* !CONFIG_MPC5200_DDR */
-
-#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_CFG 0x00047801
-#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-
-#endif /* CONFIG_MPC5200_DDR */
-#endif /*CONFIG_LITE5200B */
-
-#define CONFIG_SYS_CS_BURST 0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
-
-#define CONFIG_SYS_RESET_ADDRESS 0xff000000
-
-/*-----------------------------------------------------------------------
- * USB stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_USB_CLOCK 0x0001BBBB
-#define CONFIG_USB_CONFIG 0x00001000
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff Supports IDE harddisk
- *-----------------------------------------------------------------------
- */
-
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-
-#define CONFIG_IDE_RESET /* reset for ide supported */
-#define CONFIG_IDE_PREINIT
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
-
-/* Interval between registers */
-#define CONFIG_SYS_ATA_STRIDE 4
-
-#define CONFIG_ATAPI 1
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * (C) Copyright 2003-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
-
- */
-
-/*************************************************************************
- * (c) 2005 esd gmbh Hannover
- *
- *
- * from IceCube.h file
- * by Reinhard Arlt reinhard.arlt@esd-electronics.com
- *
- *************************************************************************/
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */
-#define CONFIG_ICECUBE 1 /* ... on IceCube board */
-#define CONFIG_CPCI5200 1 /* ... on CPCI5200 board */
-#define CONFIG_MPC5200_DDR 1 /* ... use DDR RAM */
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000 /* Standard: boot high */
-#endif
-
-#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
-#define CONFIG_BAUDRATE 9600 /* ... at 115200 bps */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*
- * PCI Mapping:
- * 0x40000000 - 0x4fffffff - PCI Memory
- * 0x50000000 - 0x50ffffff - PCI IO Space
- */
-#if 1
-#define CONFIG_PCI 1
-#if 1
-#define CONFIG_PCI_PNP 1
-#endif
-#define CONFIG_PCI_SCAN_SHOW 1
-#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
-
-#define CONFIG_PCI_MEM_BUS 0x40000000
-#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
-#define CONFIG_PCI_MEM_SIZE 0x10000000
-
-#define CONFIG_PCI_IO_BUS 0x50000000
-#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
-#define CONFIG_PCI_IO_SIZE 0x01000000
-#endif
-
-#define CONFIG_MII
-#if 0 /* test-only !!! */
-#define CONFIG_EEPRO100 1
-#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
-#define CONFIG_NS8382X 1
-#endif
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-/* USB */
-#if 0
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_STORAGE
-#endif
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#endif
-
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_DATE
-
-#if (CONFIG_SYS_TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
-# define CONFIG_SYS_LOWBOOT 1
-# define CONFIG_SYS_LOWBOOT16 1
-#endif
-#if (CONFIG_SYS_TEXT_BASE == 0xFF800000) /* Boot low with 8 MB Flash */
-# define CONFIG_SYS_LOWBOOT 1
-# define CONFIG_SYS_LOWBOOT08 1
-#endif
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Welcome to esd CPU CPCI/5200;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "flash_vxworks0=run ata_vxworks_args;setenv loadaddr ff000000;bootvx\0" \
- "flash_vxworks1=run ata_vxworks_args;setenv loadaddr ff200000:bootvx\0" \
- "net_vxworks=phypower 1;sleep 2;tftp ${loadaddr} ${image};run vxworks_args;bootvx\0" \
- "vxworks_args=setenv bootargs fec(0,0)${host}:${image} h=${serverip} e=${ipaddr} g=${gatewayip} u=${user} ${pass} tn=${target} s=${script}\0" \
- "ata_vxworks_args=setenv bootargs /ata0/vxWorks h=${serverip} e=${ipaddr} g=${gatewayip} u=${user} ${pass} tn=${target} s=${script} o=fec0 \0" \
- "loadaddr=01000000\0" \
- "serverip=192.168.2.99\0" \
- "gatewayip=10.0.0.79\0" \
- "user=mu\0" \
- "target=cpci5200.esd\0" \
- "script=cpci5200.bat\0" \
- "image=/tftpboot/vxWorks_cpci5200\0" \
- "ipaddr=10.0.13.196\0" \
- "netmask=255.255.0.0\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run flash_vxworks0"
-
-#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
-#define CONFIG_SYS_NVRAM_BASE_ADDR 0xfd010000
-#define CONFIG_SYS_NVRAM_SIZE 32*1024
-
-/*
- * IPB Bus clocking configuration.
- */
-#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED 86000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
-#define CONFIG_SYS_I2C_MULTI_EEPROMS 1
-/*
- * Flash configuration
- */
-
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_SYS_FLASH_BASE 0xFE000000
-#define CONFIG_SYS_FLASH_SIZE 0x02000000
-#define CONFIG_SYS_FLASH_INCREMENT 0x01000000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00000000)
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 128
-
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware protection */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
-
-/*
- * Environment settings
- */
-#if 1 /* test-only */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SIZE 0x20000
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_OVERWRITE 1
-#else
-#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CONFIG_ENV_OFFSET 0x0000 /* environment starts at the beginning of the EEPROM */
-#define CONFIG_ENV_SIZE 0x0400 /* 8192 bytes may be used for env vars */
- /* total size of a CAT24WC32 is 8192 bytes */
-#define CONFIG_ENV_OVERWRITE 1
-#endif
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR 0xF0000000
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
-
-/* Use SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT 1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC 1
-#define CONFIG_MPC5xxx_FEC_MII100
-/*
- * Define CONFIG_FEC_10MBIT to force FEC at 10Mb
- */
-/* #define CONFIG_FEC_10MBIT 1 */
-#define CONFIG_PHY_ADDR 0x00
-#define CONFIG_UDP_CHECKSUM 1
-
-/*
- * GPIO configuration
- */
-#define CONFIG_SYS_GPS_PORT_CONFIG 0x01052444
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL HID0_ICE
-
-#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_CFG 0x0004DD00
-
-#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-
-#define CONFIG_SYS_CS1_START 0xfd000000
-#define CONFIG_SYS_CS1_SIZE 0x00010000
-#define CONFIG_SYS_CS1_CFG 0x10101410
-
-#define CONFIG_SYS_CS3_START 0xfd010000
-#define CONFIG_SYS_CS3_SIZE 0x00010000
-#define CONFIG_SYS_CS3_CFG 0x10109410
-
-#define CONFIG_SYS_CS_BURST 0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
-
-#define CONFIG_SYS_RESET_ADDRESS 0xff000000
-
-/*-----------------------------------------------------------------------
- * USB stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_USB_CLOCK 0x0001BBBB
-#define CONFIG_USB_CONFIG 0x00001000
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff Supports IDE harddisk
- *-----------------------------------------------------------------------
- */
-
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-
-#define CONFIG_IDE_RESET /* reset for ide supported */
-#define CONFIG_IDE_PREINIT
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
-
-/* Interval between registers */
-#define CONFIG_SYS_ATA_STRIDE 4
-
-/*-----------------------------------------------------------------------
- * CPLD stuff
- */
-#define CONFIG_SYS_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */
-#define CONFIG_SYS_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for CPLD */
-
-/* CPLD program pin configuration */
-#define CONFIG_SYS_FPGA_PRG 0x20000000 /* JTAG TMS pin (ppc output) */
-#define CONFIG_SYS_FPGA_CLK 0x10000000 /* JTAG TCK pin (ppc output) */
-#define CONFIG_SYS_FPGA_DATA 0x20000000 /* JTAG TDO->TDI data pin (ppc output) */
-#define CONFIG_SYS_FPGA_DONE 0x10000000 /* JTAG TDI->TDO pin (ppc input) */
-
-#define JTAG_GPIO_ADDR_TMS (CONFIG_SYS_MBAR + 0xB10) /* JTAG TMS pin (GPS data out value reg.) */
-#define JTAG_GPIO_ADDR_TCK (CONFIG_SYS_MBAR + 0xC0C) /* JTAG TCK pin (GPW data out value reg.) */
-#define JTAG_GPIO_ADDR_TDI (CONFIG_SYS_MBAR + 0xC0C) /* JTAG TDO->TDI pin (GPW data out value reg.) */
-#define JTAG_GPIO_ADDR_TDO (CONFIG_SYS_MBAR + 0xB14) /* JTAG TDI->TDO pin (GPS data in value reg.) */
-
-#define JTAG_GPIO_ADDR_CFG (CONFIG_SYS_MBAR + 0xB00)
-#define JTAG_GPIO_CFG_SET 0x00000000
-#define JTAG_GPIO_CFG_RESET 0x00F00000
-
-#define JTAG_GPIO_ADDR_EN_TMS (CONFIG_SYS_MBAR + 0xB04)
-#define JTAG_GPIO_TMS_EN_SET 0x20000000 /* Enable for GPIO */
-#define JTAG_GPIO_TMS_EN_RESET 0x00000000
-#define JTAG_GPIO_ADDR_DDR_TMS (CONFIG_SYS_MBAR + 0xB0C)
-#define JTAG_GPIO_TMS_DDR_SET 0x20000000 /* Set as output */
-#define JTAG_GPIO_TMS_DDR_RESET 0x00000000
-
-#define JTAG_GPIO_ADDR_EN_TCK (CONFIG_SYS_MBAR + 0xC00)
-#define JTAG_GPIO_TCK_EN_SET 0x20000000 /* Enable for GPIO */
-#define JTAG_GPIO_TCK_EN_RESET 0x00000000
-#define JTAG_GPIO_ADDR_DDR_TCK (CONFIG_SYS_MBAR + 0xC08)
-#define JTAG_GPIO_TCK_DDR_SET 0x20000000 /* Set as output */
-#define JTAG_GPIO_TCK_DDR_RESET 0x00000000
-
-#define JTAG_GPIO_ADDR_EN_TDI (CONFIG_SYS_MBAR + 0xC00)
-#define JTAG_GPIO_TDI_EN_SET 0x10000000 /* Enable as GPIO */
-#define JTAG_GPIO_TDI_EN_RESET 0x00000000
-#define JTAG_GPIO_ADDR_DDR_TDI (CONFIG_SYS_MBAR + 0xC08)
-#define JTAG_GPIO_TDI_DDR_SET 0x10000000 /* Set as output */
-#define JTAG_GPIO_TDI_DDR_RESET 0x00000000
-
-#define JTAG_GPIO_ADDR_EN_TDO (CONFIG_SYS_MBAR + 0xB04)
-#define JTAG_GPIO_TDO_EN_SET 0x10000000 /* Enable as GPIO */
-#define JTAG_GPIO_TDO_EN_RESET 0x00000000
-#define JTAG_GPIO_ADDR_DDR_TDO (CONFIG_SYS_MBAR + 0xB0C)
-#define JTAG_GPIO_TDO_DDR_SET 0x00000000
-#define JTAG_GPIO_TDO_DDR_RESET 0x10000000 /* Set as input */
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * (C) Copyright 2003-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-
-/*************************************************************************
- * (c) 2005 esd gmbh Hannover
- *
- *
- * from IceCube.h file
- * by Reinhard Arlt reinhard.arlt@esd-electronics.com
- *
- *************************************************************************/
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */
-#define CONFIG_ICECUBE 1 /* ... on IceCube board */
-#define CONFIG_MECP5200 1 /* ... on MECP5200 board */
-#define CONFIG_MPC5200_DDR 1 /* ... use DDR RAM */
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-#endif
-
-#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
-#if 0 /* test-only */
-#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#else
-#define CONFIG_BAUDRATE 9600 /* ... at 115200 bps */
-#endif
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-#define CONFIG_MII
-#if 0 /* test-only !!! */
-#define CONFIG_EEPRO100 1
-#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
-#define CONFIG_NS8382X 1
-#endif
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-/* USB */
-#if 0
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_STORAGE
-#endif
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_ELF
-
-
-#if (CONFIG_SYS_TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
-# define CONFIG_SYS_LOWBOOT 1
-# define CONFIG_SYS_LOWBOOT16 1
-#endif
-#if (CONFIG_SYS_TEXT_BASE == 0xFF800000) /* Boot low with 8 MB Flash */
-# define CONFIG_SYS_LOWBOOT 1
-# define CONFIG_SYS_LOWBOOT08 1
-#endif
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Welcome to CBX-CPU5200 (mecp5200);" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "flash_vxworks0=run ata_vxworks_args;setenv loadaddr ff000000;bootvx\0" \
- "flash_vxworks1=run ata_vxworks_args;setenv loadaddr ff200000:bootvx\0" \
- "net_vxworks=tftp $(loadaddr) $(image);run vxworks_args;bootvx\0" \
- "vxworks_args=setenv bootargs fec(0,0)$(host):$(image) h=$(serverip) e=$(ipaddr) g=$(gatewayip) u=$(user) $(pass) tn=$(target) s=$(script)\0" \
- "ata_vxworks_args=setenv bootargs /ata0/vxWorks h=$(serverip) e=$(ipaddr) g=$(gatewayip) u=$(user) $(pass) tn=$(target) s=$(script) o=fec0 \0" \
- "loadaddr=01000000\0" \
- "serverip=192.168.2.99\0" \
- "gatewayip=10.0.0.79\0" \
- "user=mu\0" \
- "target=mecp5200.esd\0" \
- "script=mecp5200.bat\0" \
- "image=/tftpboot/vxWorks_mecp5200\0" \
- "ipaddr=10.0.13.196\0" \
- "netmask=255.255.0.0\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run flash_vxworks0"
-
-/*
- * IPB Bus clocking configuration.
- */
-#undef CONFIG_SYS_IPBSPEED_133 /* define for 133MHz speed */
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED 86000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
-#define CONFIG_SYS_I2C_MULTI_EEPROMS 1
-/*
- * Flash configuration
- */
-#define CONFIG_SYS_FLASH_BASE 0xFFC00000
-#define CONFIG_SYS_FLASH_SIZE 0x00400000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x003E0000)
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
-
-/*
- * Environment settings
- */
-#if 1 /* test-only */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SIZE 0x10000
-#define CONFIG_ENV_SECT_SIZE 0x10000
-#define CONFIG_ENV_OVERWRITE 1
-#else
-#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CONFIG_ENV_OFFSET 0x0000 /* environment starts at the beginning of the EEPROM */
-#define CONFIG_ENV_SIZE 0x0400 /* 8192 bytes may be used for env vars*/
- /* total size of a CAT24WC32 is 8192 bytes */
-#define CONFIG_ENV_OVERWRITE 1
-#endif
-
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Flash is CFI conformant */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware protection */
-#if 0
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#endif
-#define CONFIG_SYS_FLASH_INCREMENT 0x00400000 /* size of flash bank */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO 1 /* show if bank is empty */
-
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR 0xF0000000
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
-
-/* Use SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */
-
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT 1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC 1
-#define CONFIG_MPC5xxx_FEC_MII100
-/*
- * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
- */
-/* #define CONFIG_MPC5xxx_FEC_MII10 */
-#define CONFIG_PHY_ADDR 0x00
-#define CONFIG_UDP_CHECKSUM 1
-
-
-/*
- * GPIO configuration
- */
-#define CONFIG_SYS_GPS_PORT_CONFIG 0x01052444
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL HID0_ICE
-
-#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_CFG 0x00085d00
-
-#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-
-#define CONFIG_SYS_CS1_START 0xfd000000
-#define CONFIG_SYS_CS1_SIZE 0x00010000
-#define CONFIG_SYS_CS1_CFG 0x10101410
-
-#define CONFIG_SYS_CS_BURST 0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
-
-#define CONFIG_SYS_RESET_ADDRESS 0xff000000
-
-/*-----------------------------------------------------------------------
- * USB stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_USB_CLOCK 0x0001BBBB
-#define CONFIG_USB_CONFIG 0x00001000
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff Supports IDE harddisk
- *-----------------------------------------------------------------------
- */
-
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-
-#define CONFIG_IDE_RESET /* reset for ide supported */
-#define CONFIG_IDE_PREINIT
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
-
-/* Interval between registers */
-#define CONFIG_SYS_ATA_STRIDE 4
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * (C) Copyright 2003-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*************************************************************************
- * (c) 2005 esd gmbh Hannover
- *
- *
- * from IceCube.h file
- * by Reinhard Arlt reinhard.arlt@esd-electronics.com
- *
- *************************************************************************/
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */
-#define CONFIG_ICECUBE 1 /* ... on IceCube board */
-#define CONFIG_PF5200 1 /* ... on PF5200 board */
-#define CONFIG_MPC5200_DDR 1 /* ... use DDR RAM */
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-#endif
-
-#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
-#if 0 /* test-only */
-#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#else
-#define CONFIG_BAUDRATE 9600 /* ... at 115200 bps */
-#endif
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*
- * PCI Mapping:
- * 0x40000000 - 0x4fffffff - PCI Memory
- * 0x50000000 - 0x50ffffff - PCI IO Space
- */
-#define CONFIG_PCI 1
-#define CONFIG_PCI_PNP 1
-#define CONFIG_PCI_SCAN_SHOW 1
-#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
-
-#define CONFIG_PCI_MEM_BUS 0x40000000
-#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
-#define CONFIG_PCI_MEM_SIZE 0x10000000
-
-#define CONFIG_PCI_IO_BUS 0x50000000
-#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
-#define CONFIG_PCI_IO_SIZE 0x01000000
-
-#define CONFIG_MII 1
-#if 0 /* test-only !!! */
-#define CONFIG_EEPRO100 1
-#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
-#define CONFIG_NS8382X 1
-#endif
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-/* USB */
-#if 0
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_STORAGE
-#endif
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-
-#define CONFIG_CMD_PCI
-
-
-#if (CONFIG_SYS_TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
-# define CONFIG_SYS_LOWBOOT 1
-# define CONFIG_SYS_LOWBOOT16 1
-#endif
-#if (CONFIG_SYS_TEXT_BASE == 0xFF800000) /* Boot low with 8 MB Flash */
-# define CONFIG_SYS_LOWBOOT 1
-# define CONFIG_SYS_LOWBOOT08 1
-#endif
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Welcome to ParaFinder pf5200;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "flash_vxworks0=run ata_vxworks_args;setenv loadaddr ff000000;bootvx\0" \
- "flash_vxworks1=run ata_vxworks_args;setenv loadaddr ff200000:bootvx\0" \
- "net_vxworks=phypower 1;sleep 2;tftp ${loadaddr} ${image};run vxworks_args;bootvx\0" \
- "vxworks_args=setenv bootargs fec(0,0)${host}:${image} h=${serverip} e=${ipaddr} g=${gatewayip} u=${user} ${pass} tn=${target} s=${script}\0" \
- "ata_vxworks_args=setenv bootargs /ata0/vxWorks h=${serverip} e=${ipaddr} g=${gatewayip} u=${user} ${pass} tn=${target} s=${script} o=fec0 \0" \
- "loadaddr=01000000\0" \
- "serverip=192.168.2.99\0" \
- "gatewayip=10.0.0.79\0" \
- "user=mu\0" \
- "target=pf5200.esd\0" \
- "script=pf5200.bat\0" \
- "image=/tftpboot/vxWorks_pf5200\0" \
- "ipaddr=10.0.13.196\0" \
- "netmask=255.255.0.0\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run flash_vxworks0"
-
-/*
- * IPB Bus clocking configuration.
- */
-#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED 86000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
-#define CONFIG_SYS_I2C_MULTI_EEPROMS 1
-/*
- * Flash configuration
- */
-#define CONFIG_SYS_FLASH_BASE 0xFE000000
-#define CONFIG_SYS_FLASH_SIZE 0x02000000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00000000)
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
-
-/*
- * Environment settings
- */
-#if 1 /* test-only */
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SIZE 0x10000
-#define CONFIG_ENV_SECT_SIZE 0x10000
-#define CONFIG_ENV_OVERWRITE 1
-#else
-#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CONFIG_ENV_OFFSET 0x0000 /* environment starts at the beginning of the EEPROM */
-#define CONFIG_ENV_SIZE 0x0400 /* 8192 bytes may be used for env vars */
- /* total size of a CAT24WC32 is 8192 bytes */
-#define CONFIG_ENV_OVERWRITE 1
-#endif
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR 0xF0000000
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
-
-/* Use SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT 1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC 1
-#define CONFIG_MPC5xxx_FEC_MII100
-/*
- * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
- */
-/* #define CONFIG_MPC5xxx_FEC_MII10 */
-#define CONFIG_PHY_ADDR 0x00
-#define CONFIG_UDP_CHECKSUM 1
-
-/*
- * GPIO configuration
- */
-#define CONFIG_SYS_GPS_PORT_CONFIG 0x01052444
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL HID0_ICE
-
-#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_CFG 0x0004DD00
-
-#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-
-#define CONFIG_SYS_CS1_START 0xfd000000
-#define CONFIG_SYS_CS1_SIZE 0x00010000
-#define CONFIG_SYS_CS1_CFG 0x10101410
-
-#define CONFIG_SYS_CS_BURST 0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
-
-#define CONFIG_SYS_RESET_ADDRESS 0xff000000
-
-/*-----------------------------------------------------------------------
- * USB stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_USB_CLOCK 0x0001BBBB
-#define CONFIG_USB_CONFIG 0x00001000
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff Supports IDE harddisk
- *-----------------------------------------------------------------------
- */
-
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-
-#define CONFIG_IDE_RESET /* reset for ide supported */
-#define CONFIG_IDE_PREINIT
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
-
-/* Interval between registers */
-#define CONFIG_SYS_ATA_STRIDE 4
-
-/*-----------------------------------------------------------------------
- * CPLD stuff
- */
-#define CONFIG_SYS_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */
-#define CONFIG_SYS_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for CPLD */
-
-/* CPLD program pin configuration */
-#define CONFIG_SYS_FPGA_PRG 0x20000000 /* JTAG TMS pin (ppc output) */
-#define CONFIG_SYS_FPGA_CLK 0x10000000 /* JTAG TCK pin (ppc output) */
-#define CONFIG_SYS_FPGA_DATA 0x20000000 /* JTAG TDO->TDI data pin (ppc output) */
-#define CONFIG_SYS_FPGA_DONE 0x10000000 /* JTAG TDI->TDO pin (ppc input) */
-
-#define JTAG_GPIO_ADDR_TMS (CONFIG_SYS_MBAR + 0xB10) /* JTAG TMS pin (GPS data out value reg.) */
-#define JTAG_GPIO_ADDR_TCK (CONFIG_SYS_MBAR + 0xC0C) /* JTAG TCK pin (GPW data out value reg.) */
-#define JTAG_GPIO_ADDR_TDI (CONFIG_SYS_MBAR + 0xC0C) /* JTAG TDO->TDI pin (GPW data out value reg.) */
-#define JTAG_GPIO_ADDR_TDO (CONFIG_SYS_MBAR + 0xB14) /* JTAG TDI->TDO pin (GPS data in value reg.) */
-
-#define JTAG_GPIO_ADDR_CFG (CONFIG_SYS_MBAR + 0xB00)
-#define JTAG_GPIO_CFG_SET 0x00000000
-#define JTAG_GPIO_CFG_RESET 0x00F00000
-
-#define JTAG_GPIO_ADDR_EN_TMS (CONFIG_SYS_MBAR + 0xB04)
-#define JTAG_GPIO_TMS_EN_SET 0x20000000 /* Enable for GPIO */
-#define JTAG_GPIO_TMS_EN_RESET 0x00000000
-#define JTAG_GPIO_ADDR_DDR_TMS (CONFIG_SYS_MBAR + 0xB0C)
-#define JTAG_GPIO_TMS_DDR_SET 0x20000000 /* Set as output */
-#define JTAG_GPIO_TMS_DDR_RESET 0x00000000
-
-#define JTAG_GPIO_ADDR_EN_TCK (CONFIG_SYS_MBAR + 0xC00)
-#define JTAG_GPIO_TCK_EN_SET 0x20000000 /* Enable for GPIO */
-#define JTAG_GPIO_TCK_EN_RESET 0x00000000
-#define JTAG_GPIO_ADDR_DDR_TCK (CONFIG_SYS_MBAR + 0xC08)
-#define JTAG_GPIO_TCK_DDR_SET 0x20000000 /* Set as output */
-#define JTAG_GPIO_TCK_DDR_RESET 0x00000000
-
-#define JTAG_GPIO_ADDR_EN_TDI (CONFIG_SYS_MBAR + 0xC00)
-#define JTAG_GPIO_TDI_EN_SET 0x10000000 /* Enable as GPIO */
-#define JTAG_GPIO_TDI_EN_RESET 0x00000000
-#define JTAG_GPIO_ADDR_DDR_TDI (CONFIG_SYS_MBAR + 0xC08)
-#define JTAG_GPIO_TDI_DDR_SET 0x10000000 /* Set as output */
-#define JTAG_GPIO_TDI_DDR_RESET 0x00000000
-
-#define JTAG_GPIO_ADDR_EN_TDO (CONFIG_SYS_MBAR + 0xB04)
-#define JTAG_GPIO_TDO_EN_SET 0x10000000 /* Enable as GPIO */
-#define JTAG_GPIO_TDO_EN_RESET 0x00000000
-#define JTAG_GPIO_ADDR_DDR_TDO (CONFIG_SYS_MBAR + 0xB0C)
-#define JTAG_GPIO_TDO_DDR_SET 0x00000000
-#define JTAG_GPIO_TDO_DDR_RESET 0x10000000 /* Set as input */
-
-#endif /* __CONFIG_H */
projects / u-boot / commitdiff