a320evb FA526 (ARM920T-like) (a320 SoC)
+Eric Cooper <ecc@cmu.edu>
+
+ dockstar ARM926EJS (Kirkwood SoC)
+
George G. Davis <gdavis@mvista.com>
assabet SA1100
--- /dev/null
+#
+# Copyright (C) 2010 Eric C. Cooper <ecc@cmu.edu>
+#
+# Based on sheevaplug/Makefile originally written by
+# Prafulla Wadaskar <prafulla@marvell.com>
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := dockstar.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+/*
+ * Copyright (C) 2010 Eric C. Cooper <ecc@cmu.edu>
+ *
+ * Based on sheevaplug.c originally written by
+ * Prafulla Wadaskar <prafulla@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "dockstar.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ kw_config_gpio(DOCKSTAR_OE_VAL_LOW,
+ DOCKSTAR_OE_VAL_HIGH,
+ DOCKSTAR_OE_LOW, DOCKSTAR_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_UART0_RTS,
+ MPP9_UART0_CTS,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_SD_CLK,
+ MPP13_SD_CMD,
+ MPP14_SD_D0,
+ MPP15_SD_D1,
+ MPP16_SD_D2,
+ MPP17_SD_D3,
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GPIO,
+ MPP21_GPIO,
+ MPP22_GPIO,
+ MPP23_GPIO,
+ MPP24_GPIO,
+ MPP25_GPIO,
+ MPP26_GPIO,
+ MPP27_GPIO,
+ MPP28_GPIO,
+ MPP29_TSMP9,
+ MPP30_GPIO,
+ MPP31_GPIO,
+ MPP32_GPIO,
+ MPP33_GPIO,
+ MPP34_GPIO,
+ MPP35_GPIO,
+ MPP36_GPIO,
+ MPP37_GPIO,
+ MPP38_GPIO,
+ MPP39_GPIO,
+ MPP40_GPIO,
+ MPP41_GPIO,
+ MPP42_GPIO,
+ MPP43_GPIO,
+ MPP44_GPIO,
+ MPP45_GPIO,
+ MPP46_GPIO,
+ MPP47_GPIO,
+ MPP48_GPIO,
+ MPP49_GPIO,
+ 0
+ };
+ kirkwood_mpp_conf(kwmpp_config);
+ return 0;
+}
+
+int board_init(void)
+{
+ /*
+ * arch number of board
+ */
+ gd->bd->bi_arch_number = MACH_TYPE_DOCKSTAR;
+
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1116 PHY */
+void reset_phy(void)
+{
+ u16 reg;
+ u16 devadr;
+ char *name = "egiga0";
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..%s could not read PHY dev address\n",
+ __FUNCTION__);
+ return;
+ }
+
+ /*
+ * Enable RGMII delay on Tx and Rx for CPU port
+ * Ref: sec 4.7.2 of chip datasheet
+ */
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+ miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
+ reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+ /* reset the phy */
+ miiphy_reset(name, devadr);
+
+ printf("88E1116 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
+
+#define GREEN_LED (1 << 14)
+#define ORANGE_LED (1 << 15)
+#define BOTH_LEDS (GREEN_LED | ORANGE_LED)
+#define NEITHER_LED 0
+
+static void set_leds(u32 leds, u32 blinking)
+{
+ struct kwgpio_registers *r = (struct kwgpio_registers *)KW_GPIO1_BASE;
+ u32 oe = readl(&r->oe) | BOTH_LEDS;
+ writel(oe & ~leds, &r->oe); /* active low */
+ u32 bl = readl(&r->blink_en) & ~BOTH_LEDS;
+ writel(bl | blinking, &r->blink_en);
+}
+
+void show_boot_progress(int val)
+{
+ switch (val) {
+ case 15: /* booting Linux */
+ set_leds(BOTH_LEDS, NEITHER_LED);
+ break;
+ case 64: /* Ethernet initialization */
+ set_leds(GREEN_LED, GREEN_LED);
+ break;
+ default:
+ if (val < 0) /* error */
+ set_leds(ORANGE_LED, ORANGE_LED);
+ break;
+ }
+}
--- /dev/null
+/*
+ * Copyright (C) 2010 Eric C. Cooper <ecc@cmu.edu>
+ *
+ * Based on sheevaplug.h originally written by
+ * Prafulla Wadaskar <prafulla@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __DOCKSTAR_H
+#define __DOCKSTAR_H
+
+#define DOCKSTAR_OE_LOW (~(0))
+#define DOCKSTAR_OE_HIGH (~(0))
+#define DOCKSTAR_OE_VAL_LOW (1 << 29) /* USB_PWEN low */
+#define DOCKSTAR_OE_VAL_HIGH (1 << 17) /* LED pin high */
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG 10
+#define MV88E1116_CPRSP_CR3_REG 21
+#define MV88E1116_MAC_CTRL_REG 21
+#define MV88E1116_PGADR_REG 22
+#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
+
+#endif /* __DOCKSTAR_H */
--- /dev/null
+#
+# Copyright (C) 2010 Eric C. Cooper <ecc@cmu.edu>
+#
+# Based on sheevaplug/kwbimage.cfg originally written by
+# Prafulla Wadaskar <prafulla@marvell.com>
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM nand
+NAND_ECC_MODE default
+NAND_PAGE_SIZE 0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b1b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000c30 # DDR Configuration register
+# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
+# bit 4: 0=addr/cmd in smame cycle
+# bit 5: 0=clk is driven during self refresh, we don't care for APX
+# bit 6: 0=use recommended falling edge of clk for addr/cmd
+# bit14: 0=input buffer always powered up
+# bit18: 1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31: 0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
+# bit3-0: TRAS lsbs
+# bit7-4: TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20: TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
+# bit6-0: TRFC
+# bit8-7: TR2R
+# bit10-9: TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x0000000d # DDR Address Control
+# bit1-0: 00, Cs0width=x8
+# bit3-2: 11, Cs0size=1Gb
+# bit5-4: 00, Cs1width=nonexistent
+# bit7-6: 00, Cs1size =nonexistent
+# bit9-8: 00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16: 0, Cs0AddrSel
+# bit17: 0, Cs1AddrSel
+# bit18: 0, Cs2AddrSel
+# bit19: 0, Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
+# bit0: 0, OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000 # DDR Operation
+# bit3-0: 0x0, DDR cmd
+# bit31-4: 0 required
+
+DATA 0xFFD0141C 0x00000C52 # DDR Mode
+# bit2-0: 2, BurstLen=2 required
+# bit3: 0, BurstType=0 required
+# bit6-4: 4, CL=5
+# bit7: 0, TestMode=0 normal
+# bit8: 0, DLL reset=0 normal
+# bit11-9: 6, auto-precharge write recovery ????????????
+# bit12: 0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000040 # DDR Extended Mode
+# bit0: 0, DDR DLL enabled
+# bit1: 0, DDR drive strenght normal
+# bit2: 0, DDR ODT control lsd (disabled)
+# bit5-3: 000, required
+# bit6: 1, DDR ODT control msb, (disabled)
+# bit9-7: 000, required
+# bit10: 0, differential DQS enabled
+# bit11: 0, required
+# bit12: 0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
+# bit2-0: 111, required
+# bit3 : 1 , MBUS Burst Chop disabled
+# bit6-4: 111, required
+# bit7 : 0
+# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9 : 0 , no half clock cycle addition to dataout
+# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0 required
+
+DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size
+# bit0: 1, Window enabled
+# bit1: 0, Write Protect disabled
+# bit3-2: 00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x07, Size (i.e. 128MB)
+
+DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
+DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
+
+DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low)
+DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
+# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
+# bit3-2: 01, ODT1 active NEVER!
+# bit31-4: zero, required
+
+DATA 0xFFD0149C 0x0000E803 # CPU ODT Control
+DATA 0xFFD01480 0x00000001 # DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0
pm9263 arm arm926ejs - ronetix at91
suen3 arm arm926ejs km_arm keymile kirkwood
rd6281a arm arm926ejs - Marvell kirkwood
+dockstar arm arm926ejs - Seagate kirkwood
jadecpu arm arm926ejs jadecpu syteco mb86r0x
mx51evk arm armv7 mx51evk freescale mx5
vision2 arm armv7 vision2 ttcontrol mx5
--- /dev/null
+/*
+ * Copyright (C) 2010 Eric C. Cooper <ecc@cmu.edu>
+ *
+ * Based on sheevaplug.h originally written by
+ * Prafulla Wadaskar <prafulla@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_DOCKSTAR_H
+#define _CONFIG_DOCKSTAR_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING "\nSeagate FreeAgent DockStar"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_MACH_DOCKSTAR /* Machine type */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+#undef CONFIG_SYS_PROMPT /* previously defined in mv-common.h */
+#define CONFIG_SYS_PROMPT "DockStar> " /* Command Prompt */
+
+/*
+ * Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE 0x20000 /* 128k */
+#define CONFIG_ENV_ADDR 0x60000
+#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND \
+ "setenv bootargs ${console} ${mtdparts} ${bootargs_root}; " \
+ "ubi part root; " \
+ "ubifsmount root; " \
+ "ubifsload 0x800000 ${kernel}; " \
+ "ubifsload 0x1100000 ${initrd}; " \
+ "bootm 0x800000 0x1100000"
+
+#define CONFIG_MTDPARTS "mtdparts=orion_nand:1m(uboot),-(root)\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "console=console=ttyS0,115200\0" \
+ "mtdids=nand0=orion_nand\0" \
+ "mtdparts="CONFIG_MTDPARTS \
+ "kernel=/boot/uImage\0" \
+ "initrd=/boot/uInitrd\0" \
+ "bootargs_root=ubi.mtd=1 root=ubi0:root rootfstype=ubifs ro\0"
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR 0
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * File system
+ */
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_LZO
+
+#endif /* _CONFIG_DOCKSTAR_H */
projects / u-boot / commitdiff