i2c, mpc83xx: add CONFIG_SYS_I2C_INIT_BOARD for fsl_i2c

This patch adds the possibility to call a board specific
i2c bus reset routine for the fsl_i2c bus driver, and adds
this option for the keymile kmeter1 board.

The deblock sequence for this board is implemented and
tested in the following way:

CR = 0x20 (release SDA and SCL pin)
CR = 0xa0 (start read)
dummy read
dummy read
if 2. dummy read == 0x00
	3. dummy read

CR = 0x80 (SDA and SCL now 1 SR = 0x86)
CR = 0x00 (Modul reset SR=0x81)
CR = 0x80 (SDA and SCL = 1, SR = 0x81)

Signed-off-by: Heiko Schocher <hs@denx.de>

diff --git a/board/keymile/common/common.c b/board/keymile/common/common.c
index 259462360ce6ba4d41970c8ca5fecc792888fc95..ec27bdae2239c1a92409e03e4df5b753ecad1826 100644 (file)
--- a/board/keymile/common/common.c
+++ b/board/keymile/common/common.c
@@ -424,6 +424,7 @@ static int get_scl (void)
 
 #endif
 
+#if !defined(CONFIG_KMETER1)
 static void writeStartSeq (void)
 {
        set_sda (1);
@@ -474,6 +475,7 @@ static int i2c_make_abort (void)
        get_sda ();
        return ret;
 }
+#endif
 
 /**
  * i2c_init_board - reset i2c bus. When the board is powercycled during a
@@ -481,6 +483,23 @@ static int i2c_make_abort (void)
  */
 void i2c_init_board(void)
 {
+#if defined(CONFIG_KMETER1)
+       struct fsl_i2c *dev;
+       dev = (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C_OFFSET);
+       uchar   dummy;
+
+       out_8 (&dev->cr, (I2C_CR_MSTA));
+       out_8 (&dev->cr, (I2C_CR_MEN | I2C_CR_MSTA));
+       dummy = in_8(&dev->dr);
+       dummy = in_8(&dev->dr);
+       if (dummy != 0xff) {
+               dummy = in_8(&dev->dr);
+       }
+       out_8 (&dev->cr, (I2C_CR_MEN));
+       out_8 (&dev->cr, 0x00);
+       out_8 (&dev->cr, (I2C_CR_MEN));
+
+#else
 #if defined(CONFIG_HARD_I2C)
        volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR ;
        volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c;
@@ -500,6 +519,7 @@ void i2c_init_board(void)
        /* Set the PortPins back to use for I2C */
        setports (0);
 #endif
+#endif
 }
 #endif
 #endif

diff --git a/drivers/i2c/fsl_i2c.c b/drivers/i2c/fsl_i2c.c
index 6ab7d3d9fcf6d9726987f0c61ed92e50e083106e..ce0f301e131077f9b8450711fc4dfdf7f944896c 100644 (file)
--- a/drivers/i2c/fsl_i2c.c
+++ b/drivers/i2c/fsl_i2c.c
@@ -178,6 +178,12 @@ i2c_init(int speed, int slaveadd)
        struct fsl_i2c *dev;
        unsigned int temp;
 
+#ifdef CONFIG_SYS_I2C_INIT_BOARD
+       /* call board specific i2c bus reset routine before accessing the   */
+       /* environment, which might be in a chip on that bus. For details   */
+       /* about this problem see doc/I2C_Edge_Conditions.                  */
+       i2c_init_board();
+#endif
        dev = (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C_OFFSET);
 
        writeb(0, &dev->cr);                    /* stop I2C controller */

diff --git a/include/configs/kmeter1.h b/include/configs/kmeter1.h
index 347b47c6516f901e07e66e98050b9a889264a3a8..63ecdae0e0edcdec1c940a2aff9aeda55c273958 100644 (file)
--- a/include/configs/kmeter1.h
+++ b/include/configs/kmeter1.h
@@ -33,7 +33,6 @@
 /* include common defines/options for all Keymile boards */
 #include "keymile-common.h"
 
-#undef CONFIG_SYS_I2C_INIT_BOARD
 #define CONFIG_MISC_INIT_R     1
 /*
  * System Clock Setup