If defined, the x86 reset vector code is included. This is not
needed when U-Boot is running from Coreboot.
-- CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC:
- Enables the RTC32K OSC on AM33xx based plattforms
-
- CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
Option to disable subpage write in NAND driver
driver that uses this:
If your ATF is affected, say Y.
+config SPL_AM33XX_ENABLE_RTC32K_OSC
+ bool "Enable the RTC32K OSC on AM33xx based platforms"
+ default y if AM33XX
+ help
+ Enable access to the AM33xx RTC and select the external 32kHz clock
+ source.
+
config TPL
bool
depends on SUPPORT_TPL
CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_POWER_SUPPORT=y
CONFIG_SPL_YMODEM_SUPPORT=y
+# CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is not set
CONFIG_SYS_PROMPT="U-Boot# "
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Enter 'shc' to enter prompt (times out) %d \nEnter 'noautoboot' to enter prompt without timeout\n"
CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_POWER_SUPPORT=y
CONFIG_SPL_YMODEM_SUPPORT=y
+# CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is not set
CONFIG_SYS_PROMPT="U-Boot# "
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Enter 'shc' to enter prompt (times out) %d \nEnter 'noautoboot' to enter prompt without timeout\n"
CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_POWER_SUPPORT=y
CONFIG_SPL_YMODEM_SUPPORT=y
+# CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is not set
CONFIG_SYS_PROMPT="U-Boot# "
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Enter 'shc' to enter prompt (times out) %d \nEnter 'noautoboot' to enter prompt without timeout\n"
CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_POWER_SUPPORT=y
CONFIG_SPL_YMODEM_SUPPORT=y
+# CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is not set
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Enter 'shc' to enter prompt (times out) %d \nEnter 'noautoboot' to enter prompt without timeout\n"
CONFIG_AUTOBOOT_DELAY_STR="shc"
CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_POWER_SUPPORT=y
CONFIG_SPL_YMODEM_SUPPORT=y
+# CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is not set
CONFIG_SYS_PROMPT="U-Boot# "
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Enter 'shc' to enter prompt (times out) %d \nEnter 'noautoboot' to enter prompt without timeout\n"
CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_POWER_SUPPORT=y
CONFIG_SPL_YMODEM_SUPPORT=y
+# CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is not set
CONFIG_SYS_PROMPT="U-Boot# "
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Enter 'shc' to enter prompt (times out) %d \nEnter 'noautoboot' to enter prompt without timeout\n"
CONFIG_SPL_I2C_SUPPORT=y
CONFIG_SPL_MTD_SUPPORT=y
CONFIG_SPL_POWER_SUPPORT=y
+# CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is not set
CONFIG_SYS_PROMPT="CM-T335 # "
CONFIG_CMD_ASKENV=y
CONFIG_CMD_EEPROM=y
CONFIG_SPL=y
CONFIG_SPL_I2C_SUPPORT=y
CONFIG_SPL_YMODEM_SUPPORT=y
+# CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is not set
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot# "
CONFIG_AUTOBOOT_KEYED=y
CONFIG_SPL=y
CONFIG_SPL_I2C_SUPPORT=y
CONFIG_SPL_YMODEM_SUPPORT=y
+# CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is not set
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot# "
CONFIG_AUTOBOOT_KEYED=y
CONFIG_SPL=y
CONFIG_SPL_I2C_SUPPORT=y
CONFIG_SPL_YMODEM_SUPPORT=y
+# CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is not set
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot# "
CONFIG_AUTOBOOT_KEYED=y
CONFIG_SPL=y
CONFIG_SPL_I2C_SUPPORT=y
CONFIG_SPL_YMODEM_SUPPORT=y
+# CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is not set
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot# "
CONFIG_AUTOBOOT_KEYED=y
config BOOTCOUNT_AM33XX
bool "Boot counter in AM33XX RTC IP block"
depends on AM33XX || SOC_DA8XX
+ select SPL_AM33XX_ENABLE_RTC32K_OSC if AM33XX
help
A bootcount driver for the RTC IP block found on many TI platforms.
This requires the RTC clocks, etc, to be enabled prior to use and
#include <configs/ti_am335x_common.h>
/* settings we don;t want on this board */
-#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
#undef CONFIG_CMD_SPI
#define CONFIG_CMD_CACHE
/* Timer information */
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */
-#define CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC /* enable 32kHz OSC at bootime */
#define CONFIG_POWER_TPS65217
#include <asm/arch/omap.h>
#include <configs/ti_am335x_common.h>
#undef CONFIG_SPI
-#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
#undef CONFIG_MAX_RAM_BANK_SIZE
#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* 512MB */
#include "siemens-am33x-common.h"
#define DDR_PLL_FREQ 303
-#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
#define BOARD_DFU_BUTTON_GPIO 27 /* Use as default */
#define GPIO_LAN9303_NRST 88 /* GPIO2_24 = gpio88 */
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define DDR_PLL_FREQ 303
-#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
/* FWD Button = 27
* SRV Button = 87 */
#include "siemens-am33x-common.h"
#define DDR_PLL_FREQ 303
-#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
/* FWD Button = 27
* SRV Button = 87 */
#include "siemens-am33x-common.h"
#define DDR_PLL_FREQ 303
-#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
#define BOARD_DFU_BUTTON_GPIO 27 /* Use as default */
#define GPIO_LAN9303_NRST 88 /* GPIO2_24 = gpio88 */
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */
#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */
-#define CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
#include <asm/arch/omap.h>
CONFIG_SPLASH_SOURCE
CONFIG_SPLL_FREQ
CONFIG_SPL_
-CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
CONFIG_SPL_ATMEL_SIZE
CONFIG_SPL_BOARD_LOAD_IMAGE
CONFIG_SPL_BOOTROM_SAVE