This board has not been converted to generic board by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
select CPU_V7
select SUPPORT_SPL
-config TARGET_IMA3_MX53
- bool "Support ima3-mx53"
- select CPU_V7
-
config TARGET_MX51EVK
bool "Support mx51evk"
select CPU_V7
source "board/davedenx/qong/Kconfig"
source "board/denx/m28evk/Kconfig"
source "board/denx/m53evk/Kconfig"
-source "board/esg/ima3-mx53/Kconfig"
source "board/freescale/ls2085a/Kconfig"
source "board/freescale/ls2085aqds/Kconfig"
source "board/freescale/ls2085ardb/Kconfig"
+++ /dev/null
-if TARGET_IMA3_MX53
-
-config SYS_BOARD
- default "ima3-mx53"
-
-config SYS_VENDOR
- default "esg"
-
-config SYS_SOC
- default "mx5"
-
-config SYS_CONFIG_NAME
- default "ima3-mx53"
-
-endif
+++ /dev/null
-IMA3-MX53 BOARD
-#M: -
-S: Maintained
-F: board/esg/ima3-mx53/
-F: include/configs/ima3-mx53.h
-F: configs/ima3-mx53_defconfig
+++ /dev/null
-#
-# Copyright (C) 2012, Stefano Babic <sbabic@denx.de>
-#
-# Based on ti/evm/Makefile
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := ima3-mx53.o
+++ /dev/null
-/*
- * (C) Copyright 2012, Stefano Babic <sbabic@denx.de>
- *
- * (C) Copyright 2010 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/iomux-mx53.h>
-#include <asm/errno.h>
-#include <netdev.h>
-#include <mmc.h>
-#include <fsl_esdhc.h>
-#include <asm/gpio.h>
-
-/* NOR flash configuration */
-#define IMA3_MX53_CS0GCR1 (CSEN | DSZ(2))
-#define IMA3_MX53_CS0GCR2 0
-#define IMA3_MX53_CS0RCR1 (RCSN(2) | OEN(1) | RWSC(15))
-#define IMA3_MX53_CS0RCR2 0
-#define IMA3_MX53_CS0WCR1 (WBED1 | WCSN(2) | WEN(1) | WWSC(15))
-#define IMA3_MX53_CS0WCR2 0
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static void weim_nor_settings(void)
-{
- struct weim *weim_regs = (struct weim *)WEIM_BASE_ADDR;
-
- writel(IMA3_MX53_CS0GCR1, &weim_regs->cs0gcr1);
- writel(IMA3_MX53_CS0GCR2, &weim_regs->cs0gcr2);
- writel(IMA3_MX53_CS0RCR1, &weim_regs->cs0rcr1);
- writel(IMA3_MX53_CS0RCR2, &weim_regs->cs0rcr2);
- writel(IMA3_MX53_CS0WCR1, &weim_regs->cs0wcr1);
- writel(IMA3_MX53_CS0WCR2, &weim_regs->cs0wcr2);
- writel(0x0, &weim_regs->wcr);
-
- set_chipselect_size(CS0_128);
-}
-
-int dram_init(void)
-{
- gd->ram_size = get_ram_size((void *) CONFIG_SYS_SDRAM_BASE,
- PHYS_SDRAM_1_SIZE);
- return 0;
-}
-
-#define UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
-
-static void setup_iomux_uart(void)
-{
- static const iomux_v3_cfg_t uart_pads[] = {
- NEW_PAD_CTRL(MX53_PAD_CSI0_DAT13__UART4_RXD_MUX, UART_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_CSI0_DAT12__UART4_TXD_MUX, UART_PAD_CTRL),
- };
-
- imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
-}
-
-static void setup_iomux_fec(void)
-{
- static const iomux_v3_cfg_t fec_pads[] = {
- NEW_PAD_CTRL(MX53_PAD_FEC_MDIO__FEC_MDIO, PAD_CTL_HYS |
- PAD_CTL_DSE_HIGH | PAD_CTL_PUS_22K_UP | PAD_CTL_ODE),
- NEW_PAD_CTRL(MX53_PAD_FEC_MDC__FEC_MDC, PAD_CTL_DSE_HIGH),
- NEW_PAD_CTRL(MX53_PAD_KEY_COL0__FEC_RDATA_3,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_KEY_COL2__FEC_RDATA_2,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_FEC_RXD1__FEC_RDATA_1,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_FEC_RXD0__FEC_RDATA_0,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_GPIO_19__FEC_TDATA_3, PAD_CTL_DSE_HIGH),
- NEW_PAD_CTRL(MX53_PAD_KEY_ROW2__FEC_TDATA_2, PAD_CTL_DSE_HIGH),
- NEW_PAD_CTRL(MX53_PAD_FEC_TXD1__FEC_TDATA_1, PAD_CTL_DSE_HIGH),
- NEW_PAD_CTRL(MX53_PAD_FEC_TXD0__FEC_TDATA_0, PAD_CTL_DSE_HIGH),
- NEW_PAD_CTRL(MX53_PAD_FEC_TX_EN__FEC_TX_EN, PAD_CTL_DSE_HIGH),
- NEW_PAD_CTRL(MX53_PAD_FEC_REF_CLK__FEC_TX_CLK,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_FEC_RX_ER__FEC_RX_ER,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_FEC_CRS_DV__FEC_RX_DV,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_KEY_COL3__FEC_CRS,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_KEY_ROW1__FEC_COL,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_KEY_COL1__FEC_RX_CLK,
- PAD_CTL_HYS | PAD_CTL_PKE),
- };
-
- imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
-}
-
-#ifdef CONFIG_FSL_ESDHC
-struct fsl_esdhc_cfg esdhc_cfg = { MMC_SDHC1_BASE_ADDR };
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- int ret;
-
- ret = !gpio_get_value(IMX_GPIO_NR(1, 1));
-
- return ret;
-}
-
-#define SD_CMD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
- PAD_CTL_PUS_100K_UP)
-#define SD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | \
- PAD_CTL_DSE_HIGH)
-#define SD_CD_PAD_CTRL (PAD_CTL_DSE_HIGH | PAD_CTL_HYS | PAD_CTL_PKE)
-
-int board_mmc_init(bd_t *bis)
-{
- static const iomux_v3_cfg_t sd1_pads[] = {
- NEW_PAD_CTRL(MX53_PAD_SD1_CMD__ESDHC1_CMD, SD_CMD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_CLK__ESDHC1_CLK, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_DATA0__ESDHC1_DAT0, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_DATA1__ESDHC1_DAT1, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_DATA2__ESDHC1_DAT2, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_DATA3__ESDHC1_DAT3, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_GPIO_1__GPIO1_1, SD_CD_PAD_CTRL),
- };
-
- imx_iomux_v3_setup_multiple_pads(sd1_pads, ARRAY_SIZE(sd1_pads));
- gpio_direction_input(IMX_GPIO_NR(1, 1));
-
- esdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
- return fsl_esdhc_initialize(bis, &esdhc_cfg);
-}
-#endif
-
-#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | PAD_CTL_PUS_47K_UP)
-
-static void setup_iomux_spi(void)
-{
- static const iomux_v3_cfg_t spi_pads[] = {
- NEW_PAD_CTRL(MX53_PAD_CSI0_DAT8__ECSPI2_SCLK, SPI_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_CSI0_DAT9__ECSPI2_MOSI, SPI_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_CSI0_DAT10__ECSPI2_MISO, SPI_PAD_CTRL),
- /* SSEL 0 */
- NEW_PAD_CTRL(MX53_PAD_CSI0_DAT11__GPIO5_29, SPI_PAD_CTRL),
- };
-
- imx_iomux_v3_setup_multiple_pads(spi_pads, ARRAY_SIZE(spi_pads));
- gpio_direction_output(IMX_GPIO_NR(5, 29), 1);
-}
-
-int board_early_init_f(void)
-{
- /* configure I/O pads */
- setup_iomux_uart();
- setup_iomux_fec();
-
- weim_nor_settings();
-
- /* configure spi */
- setup_iomux_spi();
-
- return 0;
-}
-
-int board_init(void)
-{
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
- mxc_set_sata_internal_clock();
-
- return 0;
-}
-
-#if defined(CONFIG_RESET_PHY_R)
-#include <miiphy.h>
-
-void reset_phy(void)
-{
- unsigned short reg;
-
- /* reset the phy */
- miiphy_reset("FEC", CONFIG_PHY_ADDR);
-
- /* set hard link to 100Mbit, full-duplex */
- miiphy_read("FEC", CONFIG_PHY_ADDR, MII_BMCR, ®);
- reg &= ~BMCR_ANENABLE;
- reg |= (BMCR_SPEED100 | BMCR_FULLDPLX);
- miiphy_write("FEC", CONFIG_PHY_ADDR, MII_BMCR, reg);
-
- miiphy_read("FEC", CONFIG_PHY_ADDR, 0x16, ®);
- reg |= (1 << 5);
- miiphy_write("FEC", CONFIG_PHY_ADDR, 0x16, reg);
-}
-#endif
-
-int checkboard(void)
-{
- puts("Board: IMA3_MX53\n");
-
- return 0;
-}
+++ /dev/null
-/*
- * (C) Copyright 2012
- * Stefano Babic DENX Software Engineering sbabic@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- *
- * Refer doc/README.imximage for more details about how-to configure
- * and create imximage boot image
- *
- * The syntax is taken as close as possible with the kwbimage
- */
-
-/* image version */
-IMAGE_VERSION 2
-
-/*
- * Boot Device : one of
- * spi, sd (the board has no nand neither onenand)
- */
-BOOT_FROM nor
-
-/*
- * Device Configuration Data (DCD)
- *
- * Each entry must have the format:
- * Addr-type Address Value
- *
- * where:
- * Addr-type register length (1,2 or 4 bytes)
- * Address absolute address of the register
- * value value to be stored in the register
- */
-/* IOMUX for RAM only */
-DATA 4 0x53fa8554 0x300020
-DATA 4 0x53fa8560 0x300020
-DATA 4 0x53fa8594 0x300020
-DATA 4 0x53fa8584 0x300020
-DATA 4 0x53fa8558 0x300040
-DATA 4 0x53fa8568 0x300040
-DATA 4 0x53fa8590 0x300040
-DATA 4 0x53fa857c 0x300040
-DATA 4 0x53fa8564 0x300040
-DATA 4 0x53fa8580 0x300040
-DATA 4 0x53fa8570 0x300220
-DATA 4 0x53fa8578 0x300220
-DATA 4 0x53fa872c 0x300000
-DATA 4 0x53fa8728 0x300000
-DATA 4 0x53fa871c 0x300000
-DATA 4 0x53fa8718 0x300000
-DATA 4 0x53fa8574 0x300020
-DATA 4 0x53fa8588 0x300020
-DATA 4 0x53fa855c 0x0
-DATA 4 0x53fa858c 0x0
-DATA 4 0x53fa856c 0x300040
-DATA 4 0x53fa86f0 0x300000
-DATA 4 0x53fa8720 0x300000
-DATA 4 0x53fa86fc 0x0
-DATA 4 0x53fa86f4 0x0
-DATA 4 0x53fa8714 0x0
-DATA 4 0x53fa8724 0x4000000
-
-/* DDR RAM */
-DATA 4 0x63fd9088 0x40404040
-DATA 4 0x63fd9090 0x40404040
-DATA 4 0x63fd907C 0x01420143
-DATA 4 0x63fd9080 0x01450146
-DATA 4 0x63fd9018 0x00111740
-DATA 4 0x63fd9000 0x84190000
-
-/* esdcfgX */
-DATA 4 0x63fd900C 0x9f5152e3
-DATA 4 0x63fd9010 0xb68e8a63
-DATA 4 0x63fd9014 0x01ff00db
-
-/* Read/Write command delay */
-DATA 4 0x63fd902c 0x000026d2
-
-/* Out of reset delays */
-DATA 4 0x63fd9030 0x00ff0e21
-
-/* ESDCTL ODT timing control */
-DATA 4 0x63fd9008 0x12273030
-
-/* ESDCTL power down control */
-DATA 4 0x63fd9004 0x0002002d
-
-/* Set registers in DDR memory chips */
-DATA 4 0x63fd901c 0x00008032
-DATA 4 0x63fd901c 0x00008033
-DATA 4 0x63fd901c 0x00028031
-DATA 4 0x63fd901c 0x052080b0
-DATA 4 0x63fd901c 0x04008040
-
-/* ESDCTL refresh control */
-DATA 4 0x63fd9020 0x00005800
-
-/* PHY ZQ HW control */
-DATA 4 0x63fd9040 0x05380003
-
-/* PHY ODT control */
-DATA 4 0x63fd9058 0x00022222
-
-/* start DDR3 */
-DATA 4 0x63fd901c 0x00000000
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_TARGET_IMA3_MX53=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/esg/ima3-mx53/imximage.cfg"
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_SPI_FLASH=y
-CONFIG_SYS_PROMPT="IMA3 MX53 U-Boot > "
+++ /dev/null
-/*
- * (C) Copyright 2012, Stefano Babic <sbabic@denx.de>
- *
- * Copyright (C) 2010 Freescale Semiconductor, Inc.
- *
- * Configuration settings for the MX53-EVK Freescale board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* SOC type must be included before imx-regs.h */
-#define CONFIG_MX53
-#include <asm/arch/imx-regs.h>
-
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DISPLAY_BOARDINFO
-
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-#define CONFIG_OF_LIBFDT
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024)
-
-#define CONFIG_BOARD_EARLY_INIT_F
-
-/* Enable GPIOs */
-#define CONFIG_MXC_GPIO
-
-/* UART */
-#define CONFIG_MXC_UART
-#define CONFIG_MXC_UART_BASE UART4_BASE_ADDR
-
-/* MMC */
-#define CONFIG_FSL_ESDHC
-#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-#define CONFIG_SYS_FSL_ESDHC_NUM 1
-
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_DOS_PARTITION
-
-/* Ethernet on FEC */
-#define CONFIG_MII
-
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE FEC_BASE_ADDR
-#define CONFIG_FEC_MXC_PHYADDR 0x01
-#define CONFIG_PHY_ADDR CONFIG_FEC_MXC_PHYADDR
-#define CONFIG_RESET_PHY_R
-#define CONFIG_FEC_MXC_NO_ANEG
-#define CONFIG_ETHPRIME "FEC0"
-
-/* SPI */
-#define CONFIG_HARD_SPI
-#define CONFIG_MXC_SPI
-#define CONFIG_DEFAULT_SPI_BUS 1
-#define CONFIG_DEFAULT_SPI_MODE SPI_MODE_0
-
-/* SPI FLASH - not used for environment */
-#define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
-#define CONFIG_SF_DEFAULT_SPEED 25000000
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/* Command definition */
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_MMC
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_CMD_SPI
-#define CONFIG_CMD_SF
-#define CONFIG_CMD_GPIO
-
-#define CONFIG_BOOTDELAY 3
-
-#define CONFIG_LOADADDR 0x70800000 /* loadaddr env var */
-#define CONFIG_SYS_TEXT_BASE 0xf0001400 /* uboot in nor flash */
-
-#define CONFIG_ARP_TIMEOUT 200UL
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x70000000
-#define CONFIG_SYS_MEMTEST_END 0x10000
-
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-
-#define CONFIG_CMDLINE_EDITING
-
-/* Physical Memory Map */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM_1 CSD0_BASE_ADDR
-#define PHYS_SDRAM_1_SIZE (1024 * 1024 * 1024)
-
-#define CONFIG_SYS_SDRAM_BASE (PHYS_SDRAM_1)
-#define CONFIG_SYS_INIT_RAM_ADDR (IRAM_BASE_ADDR)
-#define CONFIG_SYS_INIT_RAM_SIZE (IRAM_SIZE)
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define MTDIDS_DEFAULT "nor0=f0000000.flash"
-
-/* FLASH and environment organization */
-
-#define CONFIG_SYS_FLASH_BASE 0xF0000000
-#define CONFIG_SYS_FLASH_CFI /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER /* Use the common driver */
-#define CONFIG_FLASH_CFI_MTD /* with MTD support */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_MAX_FLASH_SECT 1024
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
-
-#define CONFIG_ENV_SIZE (8 * 1024)
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
- CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
- CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
-
-/*
- * Default environment and default scripts
- * to update uboot and load kernel
- */
-
-#define HOSTNAME ima3-mx53
-
-#define CONFIG_HOSTNAME ima3-mx53
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram0 rw\0" \
- "addip_sta=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \
- "addip=if test -n ${ipdyn};then run addip_dyn;" \
- "else run addip_sta;fi\0" \
- "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
- "addtty=setenv bootargs ${bootargs}" \
- " console=${console},${baudrate}\0" \
- "addmisc=setenv bootargs ${bootargs} ${misc}\0" \
- "console=ttymxc3\0" \
- "loadaddr=70800000\0" \
- "kernel_addr_r=70800000\0" \
- "ramdisk_addr_r=71000000\0" \
- "hostname=" __stringify(CONFIG_HOSTNAME) "\0" \
- "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0" \
- "ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/uRamdisk\0" \
- "mmcargs=setenv bootargs root=${mmcroot} " \
- "rootfstype=${mmcrootfstype}\0" \
- "mmcroot=/dev/mmcblk0p3 rw\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "run mmcargs addip addtty addmtd addmisc mmcload;" \
- "bootm\0" \
- "mmcload=fatload mmc ${mmcdev}:${mmcpart} " \
- "${loadaddr} ${uimage}\0" \
- "mmcrootfstype=ext3 rootwait\0" \
- "flash_self=run ramargs addip addtty addmtd addmisc;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
- "bootm ${kernel_addr}\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "run nfsargs addip addtty addmtd addmisc;" \
- "bootm ${kernel_addr_r}\0" \
- "net_self_load=tftp ${ramdisk_addr_r} ${ramdisk_file};" \
- "tftp ${kernel_addr_r} ${bootfile}\0" \
- "net_self=if run net_self_load;then " \
- "run ramargs addip addtty addmtd addmisc;" \
- "bootm ${kernel_addr_r} ${ramdisk_addr_r};" \
- "else echo Images not loades;fi\0" \
- "satargs=setenv bootargs root=/dev/sda1\0" \
- "satafile=boot/uImage\0" \
- "ssdboot=echo Booting from ssd ...; " \
- "run satargs addip addtty addmtd addmisc;" \
- "sata init;ext2load sata 0:1 ${kernel_addr_r} " \
- "${satafile};bootm\0" \
- "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.imx\0" \
- "uimage=uImage\0" \
- "load=tftp ${loadaddr} ${u-boot}\0" \
- "uboot_addr=0xf0001000\0" \
- "update=protect off 0xf0000000 +60000;" \
- "erase ${uboot_addr} +60000;" \
- "cp.b ${loadaddr} ${uboot_addr} ${filesize}\0" \
- "upd=if run load;then echo Updating u-boot;if run update;" \
- "then echo U-Boot updated;" \
- "else echo Error updating u-boot !;" \
- "echo Board without bootloader !!;" \
- "fi;" \
- "else echo U-Boot not downloaded..exiting;fi\0" \
- "bootcmd=run net_nfs\0"
-
-
-#define CONFIG_CMD_SATA
-#ifdef CONFIG_CMD_SATA
- #define CONFIG_DWC_AHSATA
- #define CONFIG_SYS_SATA_MAX_DEVICE 1
- #define CONFIG_DWC_AHSATA_PORT_ID 0
- #define CONFIG_DWC_AHSATA_BASE_ADDR SATA_BASE_ADDR
- #define CONFIG_LBA48
- #define CONFIG_LIBATA
-#endif
-
-#endif /* __CONFIG_H */
projects / u-boot / commitdiff