--- /dev/null
+ST DWC3 glue logic
+
+This file documents the parameters for the dwc3-st driver.
+This driver controls the glue logic used to configure the dwc3 core on
+STiH407 based platforms.
+
+Required properties:
+ - compatible : must be "st,stih407-dwc3"
+ - reg : glue logic base address and USB syscfg ctrl register offset
+ - reg-names : should be "reg-glue" and "syscfg-reg"
+ - st,syscon : should be phandle to system configuration node which
+ encompasses the glue registers
+ - resets : list of phandle and reset specifier pairs. There should be two entries, one
+ for the powerdown and softreset lines of the usb3 IP
+ - reset-names : list of reset signal names. Names should be "powerdown" and "softreset"
+
+ - #address-cells, #size-cells : should be '1' if the device has sub-nodes
+ with 'reg' property
+
+ - pinctl-names : A pinctrl state named "default" must be defined
+
+ - pinctrl-0 : Pin control group
+
+ - ranges : allows valid 1:1 translation between child's address space and
+ parent's address space
+
+Sub-nodes:
+The dwc3 core should be added as subnode to ST DWC3 glue as shown in the
+example below.
+
+NB: The dr_mode property is NOT optional for this driver, as the default value
+is "otg", which isn't supported by this SoC. Valid dr_mode values for dwc3-st are
+either "host" or "device".
+
+Example:
+
+st_dwc3: dwc3@8f94000 {
+ status = "disabled";
+ compatible = "st,stih407-dwc3";
+ reg = <0x08f94000 0x1000>, <0x110 0x4>;
+ reg-names = "reg-glue", "syscfg-reg";
+ st,syscfg = <&syscfg_core>;
+ resets = <&powerdown STIH407_USB3_POWERDOWN>,
+ <&softreset STIH407_MIPHY2_SOFTRESET>;
+ reset-names = "powerdown", "softreset";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb3>;
+ ranges;
+
+ dwc3: dwc3@9900000 {
+ compatible = "snps,dwc3";
+ reg = <0x09900000 0x100000>;
+ interrupts = <GIC_SPI 155 IRQ_TYPE_NONE>;
+ dr_mode = "host";
+ phy-names = "usb2-phy", "usb3-phy";
+ phys = <&usb2_picophy2>, <&phy_port2 PHY_TYPE_USB3>;
+ };
+};
--- /dev/null
+/*
+ * STiH407 family DWC3 specific Glue layer
+ *
+ * Copyright (c) 2017
+ * Patrice Chotard <patrice.chotard@st.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <dm.h>
+#include <errno.h>
+#include <fdtdec.h>
+#include <libfdt.h>
+#include <dm/lists.h>
+#include <regmap.h>
+#include <reset-uclass.h>
+#include <syscon.h>
+#include <usb.h>
+
+#include <linux/usb/dwc3.h>
+#include <linux/usb/otg.h>
+#include <dwc3-sti-glue.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * struct sti_dwc3_glue_platdata - dwc3 STi glue driver private structure
+ * @syscfg_base: addr for the glue syscfg
+ * @glue_base: addr for the glue registers
+ * @syscfg_offset: usb syscfg control offset
+ * @powerdown_ctl: rest controller for powerdown signal
+ * @softreset_ctl: reset controller for softreset signal
+ * @mode: drd static host/device config
+ */
+struct sti_dwc3_glue_platdata {
+ phys_addr_t syscfg_base;
+ phys_addr_t glue_base;
+ phys_addr_t syscfg_offset;
+ struct reset_ctl powerdown_ctl;
+ struct reset_ctl softreset_ctl;
+ enum usb_dr_mode mode;
+};
+
+static int sti_dwc3_glue_drd_init(struct sti_dwc3_glue_platdata *plat)
+{
+ unsigned long val;
+
+ val = readl(plat->syscfg_base + plat->syscfg_offset);
+
+ val &= USB3_CONTROL_MASK;
+
+ switch (plat->mode) {
+ case USB_DR_MODE_PERIPHERAL:
+ val &= ~(USB3_DELAY_VBUSVALID
+ | USB3_SEL_FORCE_OPMODE | USB3_FORCE_OPMODE(0x3)
+ | USB3_SEL_FORCE_DPPULLDOWN2 | USB3_FORCE_DPPULLDOWN2
+ | USB3_SEL_FORCE_DMPULLDOWN2 | USB3_FORCE_DMPULLDOWN2);
+
+ val |= USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID;
+ break;
+
+ case USB_DR_MODE_HOST:
+ val &= ~(USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID
+ | USB3_SEL_FORCE_OPMODE | USB3_FORCE_OPMODE(0x3)
+ | USB3_SEL_FORCE_DPPULLDOWN2 | USB3_FORCE_DPPULLDOWN2
+ | USB3_SEL_FORCE_DMPULLDOWN2 | USB3_FORCE_DMPULLDOWN2);
+
+ val |= USB3_DELAY_VBUSVALID;
+ break;
+
+ default:
+ error("Unsupported mode of operation %d\n", plat->mode);
+ return -EINVAL;
+ }
+ writel(val, plat->syscfg_base + plat->syscfg_offset);
+
+ return 0;
+}
+
+static void sti_dwc3_glue_init(struct sti_dwc3_glue_platdata *plat)
+{
+ unsigned long reg;
+
+ reg = readl(plat->glue_base + CLKRST_CTRL);
+
+ reg |= AUX_CLK_EN | EXT_CFG_RESET_N | XHCI_REVISION;
+ reg &= ~SW_PIPEW_RESET_N;
+
+ writel(reg, plat->glue_base + CLKRST_CTRL);
+
+ /* configure mux for vbus, powerpresent and bvalid signals */
+ reg = readl(plat->glue_base + USB2_VBUS_MNGMNT_SEL1);
+
+ reg |= SEL_OVERRIDE_VBUSVALID(USB2_VBUS_UTMIOTG) |
+ SEL_OVERRIDE_POWERPRESENT(USB2_VBUS_UTMIOTG) |
+ SEL_OVERRIDE_BVALID(USB2_VBUS_UTMIOTG);
+
+ writel(reg, plat->glue_base + USB2_VBUS_MNGMNT_SEL1);
+
+ setbits_le32(plat->glue_base + CLKRST_CTRL, SW_PIPEW_RESET_N);
+}
+
+static int sti_dwc3_glue_ofdata_to_platdata(struct udevice *dev)
+{
+ struct sti_dwc3_glue_platdata *plat = dev_get_platdata(dev);
+ struct udevice *syscon;
+ struct regmap *regmap;
+ int ret;
+ u32 reg[4];
+
+ ret = fdtdec_get_int_array(gd->fdt_blob, dev_of_offset(dev),
+ "reg", reg, ARRAY_SIZE(reg));
+ if (ret) {
+ error("unable to find st,stih407-dwc3 reg property(%d)\n", ret);
+ return ret;
+ }
+
+ plat->glue_base = reg[0];
+ plat->syscfg_offset = reg[2];
+
+ /* get corresponding syscon phandle */
+ ret = uclass_get_device_by_phandle(UCLASS_SYSCON, dev, "st,syscfg",
+ &syscon);
+ if (ret) {
+ error("unable to find syscon device (%d)\n", ret);
+ return ret;
+ }
+
+ /* get syscfg-reg base address */
+ regmap = syscon_get_regmap(syscon);
+ if (!regmap) {
+ error("unable to find regmap\n");
+ return -ENODEV;
+ }
+ plat->syscfg_base = regmap->base;
+
+ /* get powerdown reset */
+ ret = reset_get_by_name(dev, "powerdown", &plat->powerdown_ctl);
+ if (ret) {
+ error("can't get powerdown reset for %s (%d)", dev->name, ret);
+ return ret;
+ }
+
+ /* get softreset reset */
+ ret = reset_get_by_name(dev, "softreset", &plat->softreset_ctl);
+ if (ret)
+ error("can't get soft reset for %s (%d)", dev->name, ret);
+
+ return ret;
+};
+
+static int sti_dwc3_glue_bind(struct udevice *dev)
+{
+ struct sti_dwc3_glue_platdata *plat = dev_get_platdata(dev);
+ int dwc3_node;
+
+ /* check if one subnode is present */
+ dwc3_node = fdt_first_subnode(gd->fdt_blob, dev_of_offset(dev));
+ if (dwc3_node <= 0) {
+ error("Can't find subnode for %s\n", dev->name);
+ return -ENODEV;
+ }
+
+ /* check if the subnode compatible string is the dwc3 one*/
+ if (fdt_node_check_compatible(gd->fdt_blob, dwc3_node,
+ "snps,dwc3") != 0) {
+ error("Can't find dwc3 subnode for %s\n", dev->name);
+ return -ENODEV;
+ }
+
+ /* retrieve the DWC3 dual role mode */
+ plat->mode = usb_get_dr_mode(dwc3_node);
+ if (plat->mode == USB_DR_MODE_UNKNOWN)
+ /* by default set dual role mode to HOST */
+ plat->mode = USB_DR_MODE_HOST;
+
+ return dm_scan_fdt_dev(dev);
+}
+
+static int sti_dwc3_glue_probe(struct udevice *dev)
+{
+ struct sti_dwc3_glue_platdata *plat = dev_get_platdata(dev);
+ int ret;
+
+ /* deassert both powerdown and softreset */
+ ret = reset_deassert(&plat->powerdown_ctl);
+ if (ret < 0) {
+ error("DWC3 powerdown reset deassert failed: %d", ret);
+ return ret;
+ }
+
+ ret = reset_deassert(&plat->softreset_ctl);
+ if (ret < 0) {
+ error("DWC3 soft reset deassert failed: %d", ret);
+ goto softreset_err;
+ }
+
+ ret = sti_dwc3_glue_drd_init(plat);
+ if (ret)
+ goto init_err;
+
+ sti_dwc3_glue_init(plat);
+
+ return 0;
+
+init_err:
+ ret = reset_assert(&plat->softreset_ctl);
+ if (ret < 0) {
+ error("DWC3 soft reset deassert failed: %d", ret);
+ return ret;
+ }
+
+softreset_err:
+ ret = reset_assert(&plat->powerdown_ctl);
+ if (ret < 0)
+ error("DWC3 powerdown reset deassert failed: %d", ret);
+
+ return ret;
+}
+
+static int sti_dwc3_glue_remove(struct udevice *dev)
+{
+ struct sti_dwc3_glue_platdata *plat = dev_get_platdata(dev);
+ int ret;
+
+ /* assert both powerdown and softreset */
+ ret = reset_assert(&plat->powerdown_ctl);
+ if (ret < 0) {
+ error("DWC3 powerdown reset deassert failed: %d", ret);
+ return ret;
+ }
+
+ ret = reset_assert(&plat->softreset_ctl);
+ if (ret < 0)
+ error("DWC3 soft reset deassert failed: %d", ret);
+
+ return ret;
+}
+
+static const struct udevice_id sti_dwc3_glue_ids[] = {
+ { .compatible = "st,stih407-dwc3" },
+ { }
+};
+
+U_BOOT_DRIVER(dwc3_sti_glue) = {
+ .name = "dwc3_sti_glue",
+ .id = UCLASS_MISC,
+ .of_match = sti_dwc3_glue_ids,
+ .ofdata_to_platdata = sti_dwc3_glue_ofdata_to_platdata,
+ .probe = sti_dwc3_glue_probe,
+ .remove = sti_dwc3_glue_remove,
+ .bind = sti_dwc3_glue_bind,
+ .platdata_auto_alloc_size = sizeof(struct sti_dwc3_glue_platdata),
+ .flags = DM_FLAG_ALLOC_PRIV_DMA,
+};
--- /dev/null
+/*
+ * Copyright (c) 2017
+ * Patrice Chotard <patrice.chotard@st.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __DWC3_STI_UBOOT_H_
+#define __DWC3_STI_UBOOT_H_
+
+/* glue registers */
+#define CLKRST_CTRL 0x00
+#define AUX_CLK_EN BIT(0)
+#define SW_PIPEW_RESET_N BIT(4)
+#define EXT_CFG_RESET_N BIT(8)
+
+#define XHCI_REVISION BIT(12)
+
+#define USB2_VBUS_MNGMNT_SEL1 0x2C
+#define USB2_VBUS_UTMIOTG 0x1
+
+#define SEL_OVERRIDE_VBUSVALID(n) ((n) << 0)
+#define SEL_OVERRIDE_POWERPRESENT(n) ((n) << 4)
+#define SEL_OVERRIDE_BVALID(n) ((n) << 8)
+
+/* Static DRD configuration */
+#define USB3_CONTROL_MASK 0xf77
+
+#define USB3_DEVICE_NOT_HOST BIT(0)
+#define USB3_FORCE_VBUSVALID BIT(1)
+#define USB3_DELAY_VBUSVALID BIT(2)
+#define USB3_SEL_FORCE_OPMODE BIT(4)
+#define USB3_FORCE_OPMODE(n) ((n) << 5)
+#define USB3_SEL_FORCE_DPPULLDOWN2 BIT(8)
+#define USB3_FORCE_DPPULLDOWN2 BIT(9)
+#define USB3_SEL_FORCE_DMPULLDOWN2 BIT(10)
+#define USB3_FORCE_DMPULLDOWN2 BIT(11)
+
+int sti_dwc3_init(enum usb_dr_mode mode);
+
+#endif /* __DWC3_STI_UBOOT_H_ */
projects / u-boot / commitdiff