+++ /dev/null
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * (C) Copyright 2006
- * Eric Schumann, Phytec Messtechnik GmbH
- *
- * (C) Copyright 2009
- * Eric Millbrandt, DEKA Research and Development Corporation
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-#include <pci.h>
-#include <asm/io.h>
-
-#ifndef CONFIG_SYS_RAMBOOT
-static void sdram_start(int hi_addr)
-{
- volatile struct mpc5xxx_cdm *cdm =
- (struct mpc5xxx_cdm *)MPC5XXX_CDM;
- volatile struct mpc5xxx_sdram *sdram =
- (struct mpc5xxx_sdram *)MPC5XXX_SDRAM;
-
- long hi_addr_bit = hi_addr ? 0x01000000 : 0;
-
- /* unlock mode register */
- out_be32 (&sdram->ctrl,
- (SDRAM_CONTROL | 0x80000000 | hi_addr_bit));
-
- /* precharge all banks */
- out_be32 (&sdram->ctrl,
- (SDRAM_CONTROL | 0x80000002 | hi_addr_bit));
-
-#ifdef SDRAM_DDR
- /* set mode register: extended mode */
- out_be32 (&sdram->mode, (SDRAM_EMODE));
-
- /* set mode register: reset DLL */
- out_be32 (&sdram->mode, (SDRAM_MODE | 0x04000000));
-#endif
-
- /* precharge all banks */
- out_be32 (&sdram->ctrl,
- (SDRAM_CONTROL | 0x80000002 | hi_addr_bit));
-
- /* auto refresh */
- out_be32 (&sdram->ctrl,
- (SDRAM_CONTROL | 0x80000004 | hi_addr_bit));
-
- /* set mode register */
- out_be32 (&sdram->mode, (SDRAM_MODE));
-
- /* normal operation */
- out_be32 (&sdram->ctrl,
- (SDRAM_CONTROL | hi_addr_bit));
-
- /* set CDM clock enable register, set MPC5200B SDRAM bus */
- /* to reduced driver strength */
- out_be32 (&cdm->clock_enable, (0x00CFFFFF));
-}
-#endif
-
-/*
- * ATTENTION: Although partially referenced initdram does NOT make
- * real use of CONFIG_SYS_SDRAM_BASE. The code does not
- * work if CONFIG_SYS_SDRAM_BASE
- * is something else than 0x00000000.
- */
-
-phys_size_t initdram(int board_type)
-{
- volatile struct mpc5xxx_mmap_ctl *mm =
- (struct mpc5xxx_mmap_ctl *)CONFIG_SYS_MBAR;
- volatile struct mpc5xxx_sdram *sdram =
- (struct mpc5xxx_sdram *)MPC5XXX_SDRAM;
- ulong dramsize = 0;
- ulong dramsize2 = 0;
-#ifndef CONFIG_SYS_RAMBOOT
- ulong test1, test2;
-
- /* setup SDRAM chip selects */
- /* 256MB at 0x0 */
- out_be32 (&mm->sdram0, 0x0000001b);
- /* disabled */
- out_be32 (&mm->sdram1, 0x10000000);
-
- /* setup config registers */
- out_be32 (&sdram->config1, SDRAM_CONFIG1);
- out_be32 (&sdram->config2, SDRAM_CONFIG2);
-
- /* find RAM size using SDRAM CS0 only */
- sdram_start(0);
- test1 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x10000000);
- sdram_start(1);
- test2 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x10000000);
- if (test1 > test2) {
- sdram_start(0);
- dramsize = test1;
- } else
- dramsize = test2;
-
- /* memory smaller than 1MB is impossible */
- if (dramsize < (1 << 20))
- dramsize = 0;
-
- /* set SDRAM CS0 size according to the amount of RAM found */
- if (dramsize > 0) {
- out_be32 (&mm->sdram0,
- (0x13 + __builtin_ffs(dramsize >> 20) - 1));
- } else {
- /* disabled */
- out_be32 (&mm->sdram0, 0);
- }
-
-#else /* CONFIG_SYS_RAMBOOT */
-
- /* retrieve size of memory connected to SDRAM CS0 */
- dramsize = in_be32(&mm->sdram0) & 0xFF;
- if (dramsize >= 0x13)
- dramsize = (1 << (dramsize - 0x13)) << 20;
- else
- dramsize = 0;
-
- /* retrieve size of memory connected to SDRAM CS1 */
- dramsize2 = in_be32(&mm->sdram1) & 0xFF;
- if (dramsize2 >= 0x13)
- dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
- else
- dramsize2 = 0;
-
-#endif /* CONFIG_SYS_RAMBOOT */
-
- return dramsize + dramsize2;
-}
-
-int checkboard(void)
-{
- puts("Board: galaxy5200\n");
- return 0;
-}
-
-#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, bd_t *bd)
-{
- ft_cpu_setup(blob, bd);
-
- return 0;
-}
-#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
-
-void init_ide_reset (void)
-{
- volatile struct mpc5xxx_gpt *gpt = (struct mpc5xxx_gpt *)MPC5XXX_GPT;
- debug ("init_ide_reset\n");
-
- /* Configure TIMER_5 as GPIO output for ATA reset */
- /* Deassert reset */
- gpt[5].emsr = MPC5XXX_GPT_GPIO_OUT1 | MPC5XXX_GPT_TMS_GPIO;
-}
-
-void ide_set_reset (int idereset)
-{
- volatile struct mpc5xxx_gpt *gpt = (struct mpc5xxx_gpt *)MPC5XXX_GPT;
- debug ("ide_reset(%d)\n", idereset);
-
- /* Configure TIMER_5 as GPIO output for ATA reset */
- if (idereset) {
- gpt[5].emsr = MPC5XXX_GPT_GPIO_OUT0 | MPC5XXX_GPT_TMS_GPIO;
-
- /* Make a delay. MPC5200 spec says 25 usec min */
- udelay(50);
- } else {
- gpt[5].emsr = MPC5XXX_GPT_GPIO_OUT1 | MPC5XXX_GPT_TMS_GPIO;
- udelay(50);
- }
-}
-#endif /* defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET) */
+++ /dev/null
-/*
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2006
- * Eric Schumann, Phytec Messatechnik GmbH
- *
- * (C) Copyright 2009
- * Jon Smirl <jonsmirl@gmail.com>
- *
- * (C) Copyright 2009
- * Eric Millbrandt, DEKA Research and Development Corporation
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_BOARDINFO "galaxy5200"
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */
-#define CONFIG_SYS_MPC5XXX_CLKIN 33333333 /* ... running at 33.333333MHz */
-
-/*
- * Valid values for CONFIG_SYS_TEXT_BASE are:
- * 0xFFF00000 boot high (standard configuration)
- * 0xFE000000 boot low
- * 0x00100000 boot from RAM (for testing only) does not work
- */
-#ifdef CONFIG_galaxy5200_LOWBOOT
-#define CONFIG_SYS_TEXT_BASE 0xFE000000
-#endif
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000 /* Standard: boot high */
-#endif
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE 4 /* console is on PSC4 -> */
- /* define gps port conf. */
- /* register later on to */
- /* enable UART function! */
-#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_FAT
-
-#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */
-
-#if (CONFIG_SYS_TEXT_BASE == 0xFE000000) /* Boot low */
-#define CONFIG_SYS_LOWBOOT 1
-#endif
-/* RAMBOOT will be defined automatically in memory section */
-
-#define MTDIDS_DEFAULT "nor0=physmap-flash.0"
-#define MTDPARTS_DEFAULT "mtdparts=physmap-flash.0:256k(ubootl)," \
- "1792k(kernel),13312k(jffs2),256k(uboot)ro,256k(oftree),-(space)"
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY 10 /* autoboot after 10 seconds */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* allow stopping of boot process */
- /* even with bootdelay=0 */
-#define CONFIG_BOOT_RETRY_TIME 120 /* Reset if no command is entered */
-#define CONFIG_RESET_TO_RETRY
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Welcome to U-Boot;"\
- "echo"
-
-#define CONFIG_BOOTCOMMAND "go ff300004 0; go ff300004 2 2;" \
- "bootm ff040000 ff900000 fffc0000"
-#define CONFIG_BOOTARGS "console=ttyPSC0,115200"
-#define CONFIG_EXTRA_ENV_SETTINGS "epson=yes\0"
-
-/*
- * IPB Bus clocking configuration.
- */
-#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#define CONFIG_SYS_XLB_PIPELINING 1
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_INIT_MPC5XXX /* Reset devices on i2c bus */
-
-/*
- * EEPROM CAT24WC32 configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010100x */
-#define CONFIG_SYS_I2C_FACT_ADDR 0x52 /* EEPROM CAT24WC32 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
-#define CONFIG_SYS_EEPROM_SIZE 4096
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15
-
-/*
- * RTC configuration
- */
-#define RTC
-#define CONFIG_RTC_DS3231 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-
-/*
- * Flash configuration
- */
-
-#define CONFIG_SYS_FLASH_BASE 0xfe000000
-/*
- * The flash size is autoconfigured, but arch/powerpc/cpu/mpc5xxx/cpu_init.c needs this
- * variable defined
- */
-#define CONFIG_SYS_FLASH_SIZE 0x02000000
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_MAX_FLASH_SECT 259 /* max num of sects on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
- /* (= chip selects) */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-
-/*
- * Use hardware protection. This seems required, as the BDI uses hardware
- * protection. Without this, U-Boot can't work with this sectors as its
- * protection is software only by default.
- */
-#define CONFIG_SYS_FLASH_PROTECTION 1
-
-/*
- * Environment settings
- */
-
-#define CONFIG_ENV_IS_IN_EEPROM 1
-#define CONFIG_ENV_OFFSET 0x00 /* environment starts at the */
- /* beginning of the EEPROM */
-#define CONFIG_ENV_SIZE CONFIG_SYS_EEPROM_SIZE
-
-#define CONFIG_ENV_OVERWRITE 1
-
-/*
- * SDRAM configuration
- */
-#define SDRAM_DDR 1
-#define SDRAM_MODE 0x018D0000
-#define SDRAM_EMODE 0x40090000
-#define SDRAM_CONTROL 0x71500F00
-#define SDRAM_CONFIG1 0x73711930
-#define SDRAM_CONFIG2 0x47770000
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR 0xF0000000 /* MBAR has to be switched by other */
- /* bootloader or debugger config */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
-
-/* Use SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
-
-/* End of used area in SPRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT 1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/* Chip Select configuration for NAND flash */
-#define CONFIG_SYS_CS1_START 0x20000000
-#define CONFIG_SYS_CS1_SIZE 0x90000
-#define CONFIG_SYS_CS1_CFG 0x00025b00
-
-/* Chip Select configuration for Epson S1D13513 */
-#define CONFIG_SYS_CS3_START 0x10000000
-#define CONFIG_SYS_CS3_SIZE 0x400000
-#define CONFIG_SYS_CS3_CFG 0xffff3d10
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC 1
-#define CONFIG_MPC5xxx_FEC_MII100
-#define CONFIG_PHY_ADDR 0x01
-#define CONFIG_NO_AUTOLOAD 1
-
-/*
- * GPIO configuration
- *
- * GPS port configuration
- *
- * [29:31] = 01x
- * AC97 on PSC1
- * PSC1_0 -> AC97 SDATA out
- * PSC1_1 -> AC97 SDTA in
- * PSC1_2 -> AC97 SYNC out
- * PSC1_3 -> AC97 bitclock out
- * PSC1_4 -> AC97 reset out
- *
- * [28] = Reserved
- *
- * [25:27] = 110
- * SPI on PSC2
- * PSC2_0 -> MOSI
- * PSC2_1 -> MISO
- * PSC2_2 -> n/a
- * PSC2_3 -> CLK
- * PSC2_4 -> SS
- *
- * [24] = Reserved
- *
- * [20:23] = 0001
- * USB on PSC3
- * PSC3_0 -> USB_OE OE out
- * PSC3_1 -> USB_TXN Tx- out
- * PSC3_2 -> USB_TXP Tx+ out
- * PSC3_3 -> USB_TXD
- * PSC3_4 -> USB_RXP Rx+ in
- * PSC3_5 -> USB_RXN Rx- in
- * PSC3_6 -> USB_PWR PortPower out
- * PSC3_7 -> USB_SPEED speed out
- * PSC3_8 -> USB_SUSPEND suspend
- * PSC3_9 -> USB_OVRCURNT overcurrent in
- *
- * [18:19] = 10
- * Two UARTs
- *
- * [17] = 0
- * USB differential mode
- *
- * [16] = 1
- * PCI disabled
- *
- * [12:15] = 0101
- * Ethernet 100Mbit with MD
- * ETH_0 -> ETH Txen
- * ETH_1 -> ETH TxD0
- * ETH_2 -> ETH TxD1
- * ETH_3 -> ETH TxD2
- * ETH_4 -> ETH TxD3
- * ETH_5 -> ETH Txerr
- * ETH_6 -> ETH MDC
- * ETH_7 -> ETH MDIO
- * ETH_8 -> ETH RxDv
- * ETH_9 -> ETH RxCLK
- * ETH_10 -> ETH Collision
- * ETH_11 -> ETH TxD
- * ETH_12 -> ETH RxD0
- * ETH_13 -> ETH RxD1
- * ETH_14 -> ETH RxD2
- * ETH_15 -> ETH RxD3
- * ETH_16 -> ETH Rxerr
- * ETH_17 -> ETH CRS
- *
- * [9:11] = 111
- * SPI on PSC6
- * PSC6_0 -> MISO
- * PSC6_1 -> SS#
- * PSC6_2 -> MOSI
- * PSC6_3 -> CLK
- *
- * [8] = 0
- * IrDA/USB 48MHz clock generated internally
- *
- * [6:7] = 01
- * ATA chip selects on csb_4/5
- * CSB_4 -> ATA_CS0 out
- * CSB_5 -> ATA_CS1 out
- *
- * [5] = 1
- * PSC3_4 is used as CS6
- *
- * [4] = 1
- * PSC3_5 is used as CS7
- *
- * [2:3] = 00
- * No Alternatives
- *
- * [1] = 0
- * gpio_wkup_7 is GPIO
- *
- * [0] = 0
- * gpio_wkup_6 is GPIO
- *
- */
-#define CONFIG_SYS_GPS_PORT_CONFIG 0x0d75a162
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "uboot> " /* Monitor Command Prompt */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
- /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
-
-#define CONFIG_DISPLAY_BOARDINFO 1
-
-#define CONFIG_SYS_HUSH_PARSER 1
-
-#define CONFIG_CRC32_VERIFY 1
-
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-
-#define CONFIG_VERSION_VARIABLE 1
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL HID0_ICE
-
-/* no burst access on the LPB */
-#define CONFIG_SYS_CS_BURST 0x00000000
-/* one deadcycle for the 33MHz statemachine */
-#define CONFIG_SYS_CS_DEADCYCLE 0x33333331
-
-#define CONFIG_SYS_BOOTCS_CFG 0x0002d900
-#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
-
-#define CONFIG_SYS_RESET_ADDRESS 0xff000000
-
-/*
- * USB settings
- */
-#define CONFIG_USB_CLOCK 0x0001bbbb
-/* USB is on PSC3 */
-#define CONFIG_PSC3_USB
-#define CONFIG_USB_CONFIG 0x00000100
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_STORAGE
-
-/*
- * IDE/ATA stuff Supports IDE harddisk
- */
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-
-#define CONFIG_IDE_RESET 1 /* reset for ide supported */
-#define CONFIG_IDE_PREINIT
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
-/* Interval between registers */
-#define CONFIG_SYS_ATA_STRIDE 4
-#define CONFIG_ATAPI 1
-
-/* we enable IDE and FAT support, so we also need partition support */
-#define CONFIG_DOS_PARTITION 1
-
-/*
- * Open Firmware flat tree
- */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
-#define OF_CPU "PowerPC,5200@0"
-#define OF_TBCLK CONFIG_SYS_MPC5XXX_CLKIN
-#define OF_SOC "soc5200@f0000000"
-#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2600"
-
-#endif /* __CONFIG_H */
projects / u-boot / commitdiff