This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Matthias Weisser <weisserm@arcor.de>
Acked-by: Marek Vasut <marex@denx.de>
bool "Support devkit3250"
select CPU_ARM926EJS
-config TARGET_JADECPU
- bool "Support jadecpu"
- select CPU_ARM926EJS
-
config TARGET_MX25PDK
bool "Support mx25pdk"
select CPU_ARM926EJS
source "board/st-ericsson/u8500/Kconfig"
source "board/st/stv0991/Kconfig"
source "board/sunxi/Kconfig"
-source "board/syteco/jadecpu/Kconfig"
source "board/syteco/zmx25/Kconfig"
source "board/tbs/tbs2910/Kconfig"
source "board/ti/am335x/Kconfig"
obj-$(CONFIG_ARMADA100) += armada100/
obj-$(if $(filter lpc32xx,$(SOC)),y) += lpc32xx/
-obj-$(CONFIG_MB86R0x) += mb86r0x/
obj-$(CONFIG_MX25) += mx25/
obj-$(CONFIG_MX27) += mx27/
obj-$(if $(filter mxs,$(SOC)),y) += mxs/
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = clock.o reset.o timer.o
+++ /dev/null
-/*
- * (C) Copyright 2010
- * Matthias Weisser <weisserm@arcor.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-
-/*
- * Get the peripheral bus frequency depending on pll pin settings
- */
-ulong get_bus_freq(ulong dummy)
-{
- struct mb86r0x_crg * crg = (struct mb86r0x_crg *)
- MB86R0x_CRG_BASE;
- uint32_t pllmode;
-
- pllmode = readl(&crg->crpr) & MB86R0x_CRG_CRPR_PLLMODE;
-
- if (pllmode == MB86R0x_CRG_CRPR_PLLMODE_X20)
- return 40000000;
-
- return 41164767;
-}
+++ /dev/null
-/*
- * (C) Copyright 2010
- * Matthias Weisser <weisserm@arcor.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-
-/*
- * Reset the cpu by setting software reset request bit
- */
-void reset_cpu(ulong ignored)
-{
- struct mb86r0x_crg * crg = (struct mb86r0x_crg *)
- MB86R0x_CRG_BASE;
-
- writel(MB86R0x_CRSR_SWRSTREQ, &crg->crsr);
- while (1)
- /* NOP */;
- /* Never reached */
-}
+++ /dev/null
-/*
- * (C) Copyright 2007-2008
- * Stelian Pop <stelian@popies.net>
- * Lead Tech Design <www.leadtechdesign.com>
- *
- * (C) Copyright 2010
- * Matthias Weisser, Graf-Syteco <weisserm@arcor.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <div64.h>
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-
-#define TIMER_LOAD_VAL 0xffffffff
-#define TIMER_FREQ (CONFIG_MB86R0x_IOCLK / 256)
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define timestamp gd->arch.tbl
-#define lastdec gd->arch.lastinc
-
-static inline unsigned long long tick_to_time(unsigned long long tick)
-{
- tick *= CONFIG_SYS_HZ;
- do_div(tick, TIMER_FREQ);
-
- return tick;
-}
-
-static inline unsigned long long usec_to_tick(unsigned long long usec)
-{
- usec *= TIMER_FREQ;
- do_div(usec, 1000000);
-
- return usec;
-}
-
-/* nothing really to do with interrupts, just starts up a counter. */
-int timer_init(void)
-{
- struct mb86r0x_timer * timer = (struct mb86r0x_timer *)
- MB86R0x_TIMER_BASE;
- ulong ctrl = readl(&timer->control);
-
- writel(TIMER_LOAD_VAL, &timer->load);
-
- ctrl |= MB86R0x_TIMER_ENABLE | MB86R0x_TIMER_PRS_8S |
- MB86R0x_TIMER_SIZE_32;
-
- writel(ctrl, &timer->control);
-
- /* capture current value time */
- lastdec = readl(&timer->value);
- timestamp = 0; /* start "advancing" time stamp from 0 */
-
- return 0;
-}
-
-/*
- * timer without interrupts
- */
-unsigned long long get_ticks(void)
-{
- struct mb86r0x_timer * timer = (struct mb86r0x_timer *)
- MB86R0x_TIMER_BASE;
- ulong now = readl(&timer->value);
-
- if (now <= lastdec) {
- /* normal mode (non roll) */
- /* move stamp forward with absolut diff ticks */
- timestamp += lastdec - now;
- } else {
- /* we have rollover of incrementer */
- timestamp += lastdec + TIMER_LOAD_VAL - now;
- }
- lastdec = now;
- return timestamp;
-}
-
-ulong get_timer_masked(void)
-{
- return tick_to_time(get_ticks());
-}
-
-void __udelay(unsigned long usec)
-{
- unsigned long long tmp;
- ulong tmo;
-
- tmo = usec_to_tick(usec);
- tmp = get_ticks(); /* get current timestamp */
-
- while ((get_ticks() - tmp) < tmo) /* loop till event */
- /*NOP*/;
-}
-
-ulong get_timer(ulong base)
-{
- return get_timer_masked() - base;
-}
-
-/*
- * This function is derived from PowerPC code (timebase clock frequency).
- * On ARM it returns the number of timer ticks per second.
- */
-ulong get_tbclk(void)
-{
- ulong tbclk;
-
- tbclk = TIMER_FREQ;
- return tbclk;
-}
+++ /dev/null
-/*
- * (C) Copyright 2007
- *
- * Author : Carsten Schneider, mycable GmbH
- * <cs@mycable.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-#include <linux/sizes.h>
-#include <asm/arch/mb86r0x.h>
-
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2007
- *
- * mb86r0x definitions
- *
- * Author : Carsten Schneider, mycable GmbH
- * <cs@mycable.de>
- *
- * (C) Copyright 2010
- * Matthias Weisser <weisserm@arcor.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef MB86R0X_H
-#define MB86R0X_H
-
-#ifndef __ASSEMBLY__
-
-/* GPIO registers */
-struct mb86r0x_gpio {
- uint32_t gpdr0;
- uint32_t gpdr1;
- uint32_t gpdr2;
- uint32_t res;
- uint32_t gpddr0;
- uint32_t gpddr1;
- uint32_t gpddr2;
-};
-
-/* PWM registers */
-struct mb86r0x_pwm {
- uint32_t bcr;
- uint32_t tpr;
- uint32_t pr;
- uint32_t dr;
- uint32_t cr;
- uint32_t sr;
- uint32_t ccr;
- uint32_t ir;
-};
-
-/* The mb86r0x chip control (CCNT) register set. */
-struct mb86r0x_ccnt {
- uint32_t ccid;
- uint32_t csrst;
- uint32_t pad0[2];
- uint32_t cist;
- uint32_t cistm;
- uint32_t cgpio_ist;
- uint32_t cgpio_istm;
- uint32_t cgpio_ip;
- uint32_t cgpio_im;
- uint32_t caxi_bw;
- uint32_t caxi_ps;
- uint32_t cmux_md;
- uint32_t cex_pin_st;
- uint32_t cmlb;
- uint32_t pad1[1];
- uint32_t cusb;
- uint32_t pad2[41];
- uint32_t cbsc;
- uint32_t cdcrc;
- uint32_t cmsr0;
- uint32_t cmsr1;
- uint32_t pad3[2];
-};
-
-/* The mb86r0x clock reset generator */
-struct mb86r0x_crg {
- uint32_t crpr;
- uint32_t pad0;
- uint32_t crwr;
- uint32_t crsr;
- uint32_t crda;
- uint32_t crdb;
- uint32_t crha;
- uint32_t crpa;
- uint32_t crpb;
- uint32_t crhb;
- uint32_t cram;
-};
-
-/* The mb86r0x timer */
-struct mb86r0x_timer {
- uint32_t load;
- uint32_t value;
- uint32_t control;
- uint32_t intclr;
- uint32_t ris;
- uint32_t mis;
- uint32_t bgload;
-};
-
-/* mb86r0x gdc display controller */
-struct mb86r0x_gdc_dsp {
- /* Display settings */
- uint32_t dcm0;
- uint16_t pad00;
- uint16_t htp;
- uint16_t hdp;
- uint16_t hdb;
- uint16_t hsp;
- uint8_t hsw;
- uint8_t vsw;
- uint16_t pad01;
- uint16_t vtr;
- uint16_t vsp;
- uint16_t vdp;
- uint16_t wx;
- uint16_t wy;
- uint16_t ww;
- uint16_t wh;
-
- /* Layer 0 */
- uint32_t l0m;
- uint32_t l0oa;
- uint32_t l0da;
- uint16_t l0dx;
- uint16_t l0dy;
-
- /* Layer 1 */
- uint32_t l1m;
- uint32_t cbda0;
- uint32_t cbda1;
- uint32_t pad02;
-
- /* Layer 2 */
- uint32_t l2m;
- uint32_t l2oa0;
- uint32_t l2da0;
- uint32_t l2oa1;
- uint32_t l2da1;
- uint16_t l2dx;
- uint16_t l2dy;
-
- /* Layer 3 */
- uint32_t l3m;
- uint32_t l3oa0;
- uint32_t l3da0;
- uint32_t l3oa1;
- uint32_t l3da1;
- uint16_t l3dx;
- uint16_t l3dy;
-
- /* Layer 4 */
- uint32_t l4m;
- uint32_t l4oa0;
- uint32_t l4da0;
- uint32_t l4oa1;
- uint32_t l4da1;
- uint16_t l4dx;
- uint16_t l4dy;
-
- /* Layer 5 */
- uint32_t l5m;
- uint32_t l5oa0;
- uint32_t l5da0;
- uint32_t l5oa1;
- uint32_t l5da1;
- uint16_t l5dx;
- uint16_t l5dy;
-
- /* Cursor */
- uint16_t cutc;
- uint8_t cpm;
- uint8_t csize;
- uint32_t cuoa0;
- uint16_t cux0;
- uint16_t cuy0;
- uint32_t cuoa1;
- uint16_t cux1;
- uint16_t cuy1;
-
- /* Layer blending */
- uint32_t l0bld;
- uint32_t pad03;
- uint32_t l0tc;
- uint16_t l3tc;
- uint16_t l2tc;
- uint32_t pad04[15];
-
- /* Display settings */
- uint32_t dcm1;
- uint32_t dcm2;
- uint32_t dcm3;
- uint32_t pad05;
-
- /* Layer 0 extended */
- uint32_t l0em;
- uint16_t l0wx;
- uint16_t l0wy;
- uint16_t l0ww;
- uint16_t l0wh;
- uint32_t pad06;
-
- /* Layer 1 extended */
- uint32_t l1em;
- uint16_t l1wx;
- uint16_t l1wy;
- uint16_t l1ww;
- uint16_t l1wh;
- uint32_t pad07;
-
- /* Layer 2 extended */
- uint32_t l2em;
- uint16_t l2wx;
- uint16_t l2wy;
- uint16_t l2ww;
- uint16_t l2wh;
- uint32_t pad08;
-
- /* Layer 3 extended */
- uint32_t l3em;
- uint16_t l3wx;
- uint16_t l3wy;
- uint16_t l3ww;
- uint16_t l3wh;
- uint32_t pad09;
-
- /* Layer 4 extended */
- uint32_t l4em;
- uint16_t l4wx;
- uint16_t l4wy;
- uint16_t l4ww;
- uint16_t l4wh;
- uint32_t pad10;
-
- /* Layer 5 extended */
- uint32_t l5em;
- uint16_t l5wx;
- uint16_t l5wy;
- uint16_t l5ww;
- uint16_t l5wh;
- uint32_t pad11;
-
- /* Multi screen control */
- uint32_t msc;
- uint32_t pad12[3];
- uint32_t dls;
- uint32_t dbgc;
-
- /* Layer blending */
- uint32_t l1bld;
- uint32_t l2bld;
- uint32_t l3bld;
- uint32_t l4bld;
- uint32_t l5bld;
- uint32_t pad13;
-
- /* Extended transparency control */
- uint32_t l0etc;
- uint32_t l1etc;
- uint32_t l2etc;
- uint32_t l3etc;
- uint32_t l4etc;
- uint32_t l5etc;
- uint32_t pad14[10];
-
- /* YUV coefficients */
- uint32_t l1ycr0;
- uint32_t l1ycr1;
- uint32_t l1ycg0;
- uint32_t l1ycg1;
- uint32_t l1ycb0;
- uint32_t l1ycb1;
- uint32_t pad15[130];
-
- /* Layer palletes */
- uint32_t l0pal[256];
- uint32_t l1pal[256];
- uint32_t pad16[256];
- uint32_t l2pal[256];
- uint32_t l3pal[256];
- uint32_t pad17[256];
-
- /* PWM settings */
- uint32_t vpwmm;
- uint16_t vpwms;
- uint16_t vpwme;
- uint32_t vpwmc;
- uint32_t pad18[253];
-};
-
-/* mb86r0x gdc capture controller */
-struct mb86r0x_gdc_cap {
- uint32_t vcm;
- uint32_t csc;
- uint32_t vcs;
- uint32_t pad01;
-
- uint32_t cbm;
- uint32_t cboa;
- uint32_t cbla;
- uint16_t cihstr;
- uint16_t civstr;
- uint16_t cihend;
- uint16_t civend;
- uint32_t pad02;
-
- uint32_t chp;
- uint32_t cvp;
- uint32_t pad03[4];
-
- uint32_t clpf;
- uint32_t pad04;
- uint32_t cmss;
- uint32_t cmds;
- uint32_t pad05[12];
-
- uint32_t rgbhc;
- uint32_t rgbhen;
- uint32_t rgbven;
- uint32_t pad06;
- uint32_t rgbs;
- uint32_t pad07[11];
-
- uint32_t rgbcmy;
- uint32_t rgbcmcb;
- uint32_t rgbcmcr;
- uint32_t rgbcmb;
- uint32_t pad08[12 + 1984];
-};
-
-/* mb86r0x gdc draw */
-struct mb86r0x_gdc_draw {
- uint32_t ys;
- uint32_t xs;
- uint32_t dxdy;
- uint32_t xus;
- uint32_t dxudy;
- uint32_t xls;
- uint32_t dxldy;
- uint32_t usn;
- uint32_t lsn;
- uint32_t pad01[7];
- uint32_t rs;
- uint32_t drdx;
- uint32_t drdy;
- uint32_t gs;
- uint32_t dgdx;
- uint32_t dgdy;
- uint32_t bs;
- uint32_t dbdx;
- uint32_t dbdy;
- uint32_t pad02[7];
- uint32_t zs;
- uint32_t dzdx;
- uint32_t dzdy;
- uint32_t pad03[13];
- uint32_t ss;
- uint32_t dsdx;
- uint32_t dsdy;
- uint32_t ts;
- uint32_t dtdx;
- uint32_t dtdy;
- uint32_t qs;
- uint32_t dqdx;
- uint32_t dqdy;
- uint32_t pad04[23];
- uint32_t lpn;
- uint32_t lxs;
- uint32_t lxde;
- uint32_t lys;
- uint32_t lyde;
- uint32_t lzs;
- uint32_t lzde;
- uint32_t pad05[13];
- uint32_t pxdc;
- uint32_t pydc;
- uint32_t pzdc;
- uint32_t pad06[25];
- uint32_t rxs;
- uint32_t rys;
- uint32_t rsizex;
- uint32_t rsizey;
- uint32_t pad07[12];
- uint32_t saddr;
- uint32_t sstride;
- uint32_t srx;
- uint32_t sry;
- uint32_t daddr;
- uint32_t dstride;
- uint32_t drx;
- uint32_t dry;
- uint32_t brsizex;
- uint32_t brsizey;
- uint32_t tcolor;
- uint32_t pad08[93];
- uint32_t blpo;
- uint32_t pad09[7];
- uint32_t ctr;
- uint32_t ifsr;
- uint32_t ifcnt;
- uint32_t sst;
- uint32_t ds;
- uint32_t pst;
- uint32_t est;
- uint32_t pad10;
- uint32_t mdr0;
- uint32_t mdr1;
- uint32_t mdr2;
- uint32_t mdr3;
- uint32_t mdr4;
- uint32_t pad14[2];
- uint32_t mdr7;
- uint32_t fbr;
- uint32_t xres;
- uint32_t zbr;
- uint32_t tbr;
- uint32_t pfbr;
- uint32_t cxmin;
- uint32_t cxmax;
- uint32_t cymin;
- uint32_t cymax;
- uint32_t txs;
- uint32_t tis;
- uint32_t toa;
- uint32_t sho;
- uint32_t abr;
- uint32_t pad15[2];
- uint32_t fc;
- uint32_t bc;
- uint32_t alf;
- uint32_t blp;
- uint32_t pad16;
- uint32_t tbc;
- uint32_t pad11[42];
- uint32_t lx0dc;
- uint32_t ly0dc;
- uint32_t lx1dc;
- uint32_t ly1dc;
- uint32_t pad12[12];
- uint32_t x0dc;
- uint32_t y0dc;
- uint32_t x1dc;
- uint32_t y1dc;
- uint32_t x2dc;
- uint32_t y2dc;
- uint32_t pad13[666];
-};
-
-/* mb86r0x gdc geometry engine */
-struct mb86r0x_gdc_geom {
- uint32_t gctr;
- uint32_t pad00[15];
- uint32_t gmdr0;
- uint32_t gmdr1;
- uint32_t gmdr2;
- uint32_t pad01[237];
- uint32_t dfifog;
- uint32_t pad02[767];
-};
-
-/* mb86r0x gdc */
-struct mb86r0x_gdc {
- uint32_t pad00[2];
- uint32_t lts;
- uint32_t pad01;
- uint32_t lsta;
- uint32_t pad02[3];
- uint32_t ist;
- uint32_t imask;
- uint32_t pad03[6];
- uint32_t lsa;
- uint32_t lco;
- uint32_t lreq;
-
- uint32_t pad04[16*1024 - 19];
- struct mb86r0x_gdc_dsp dsp0;
- struct mb86r0x_gdc_dsp dsp1;
- uint32_t pad05[4*1024 - 2];
- uint32_t vccc;
- uint32_t vcsr;
- struct mb86r0x_gdc_cap cap0;
- struct mb86r0x_gdc_cap cap1;
- uint32_t pad06[4*1024];
- uint32_t texture_base[16*1024];
- struct mb86r0x_gdc_draw draw;
- uint32_t pad07[7*1024];
- struct mb86r0x_gdc_geom geom;
- uint32_t pad08[7*1024];
-};
-
-/* mb86r0x ddr2c */
-struct mb86r0x_ddr2c {
- uint16_t dric;
- uint16_t dric1;
- uint16_t dric2;
- uint16_t drca;
- uint16_t drcm;
- uint16_t drcst1;
- uint16_t drcst2;
- uint16_t drcr;
- uint16_t pad00[8];
- uint16_t drcf;
- uint16_t pad01[7];
- uint16_t drasr;
- uint16_t pad02[15];
- uint16_t drims;
- uint16_t pad03[7];
- uint16_t dros;
- uint16_t pad04;
- uint16_t dribsodt1;
- uint16_t dribsocd;
- uint16_t dribsocd2;
- uint16_t pad05[3];
- uint16_t droaba;
- uint16_t pad06[9];
- uint16_t drobs;
- uint16_t pad07[5];
- uint16_t drimr1;
- uint16_t drimr2;
- uint16_t drimr3;
- uint16_t drimr4;
- uint16_t droisr1;
- uint16_t droisr2;
-};
-
-/* mb86r0x memc */
-struct mb86r0x_memc {
- uint32_t mcfmode[8];
- uint32_t mcftim[8];
- uint32_t mcfarea[8];
-};
-
-#endif /* __ASSEMBLY__ */
-
-/*
- * Physical Address Defines
- */
-#define MB86R0x_DDR2_BASE 0xf3000000
-#define MB86R0x_GDC_BASE 0xf1fc0000
-#define MB86R0x_CCNT_BASE 0xfff42000
-#define MB86R0x_CAN0_BASE 0xfff54000
-#define MB86R0x_CAN1_BASE 0xfff55000
-#define MB86R0x_I2C0_BASE 0xfff56000
-#define MB86R0x_I2C1_BASE 0xfff57000
-#define MB86R0x_EHCI_BASE 0xfff80000
-#define MB86R0x_OHCI_BASE 0xfff81000
-#define MB86R0x_IRC1_BASE 0xfffb0000
-#define MB86R0x_MEMC_BASE 0xfffc0000
-#define MB86R0x_TIMER_BASE 0xfffe0000
-#define MB86R0x_UART0_BASE 0xfffe1000
-#define MB86R0x_UART1_BASE 0xfffe2000
-#define MB86R0x_IRCE_BASE 0xfffe4000
-#define MB86R0x_CRG_BASE 0xfffe7000
-#define MB86R0x_IRC0_BASE 0xfffe8000
-#define MB86R0x_GPIO_BASE 0xfffe9000
-#define MB86R0x_PWM0_BASE 0xfff41000
-#define MB86R0x_PWM1_BASE 0xfff41100
-
-#define MB86R0x_CRSR_SWRSTREQ (1 << 1)
-
-/*
- * Timer register bits
- */
-#define MB86R0x_TIMER_ENABLE (1 << 7)
-#define MB86R0x_TIMER_MODE_MSK (1 << 6)
-#define MB86R0x_TIMER_MODE_FR (0 << 6)
-#define MB86R0x_TIMER_MODE_PD (1 << 6)
-
-#define MB86R0x_TIMER_INT_EN (1 << 5)
-#define MB86R0x_TIMER_PRS_MSK (3 << 2)
-#define MB86R0x_TIMER_PRS_4S (1 << 2)
-#define MB86R0x_TIMER_PRS_8S (1 << 3)
-#define MB86R0x_TIMER_SIZE_32 (1 << 1)
-#define MB86R0x_TIMER_ONE_SHT (1 << 0)
-
-/*
- * Clock reset generator bits
- */
-#define MB86R0x_CRG_CRPR_PLLRDY (1 << 8)
-#define MB86R0x_CRG_CRPR_PLLMODE (0x1f << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X49 (0 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X46 (1 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X37 (2 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X20 (3 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X47 (4 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X44 (5 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X36 (6 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X19 (7 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X39 (8 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X38 (9 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X30 (10 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X15 (11 << 0)
-/*
- * DDR2 controller bits
- */
-#define MB86R0x_DDR2_DRCI_DRINI (1 << 15)
-#define MB86R0x_DDR2_DRCI_CKEN (1 << 14)
-#define MB86R0x_DDR2_DRCI_DRCMD (1 << 0)
-#define MB86R0x_DDR2_DRCI_CMD (MB86R0x_DDR2_DRCI_DRINI | \
- MB86R0x_DDR2_DRCI_CKEN | \
- MB86R0x_DDR2_DRCI_DRCMD)
-#define MB86R0x_DDR2_DRCI_INIT (MB86R0x_DDR2_DRCI_DRINI | \
- MB86R0x_DDR2_DRCI_CKEN)
-#define MB86R0x_DDR2_DRCI_NORMAL MB86R0x_DDR2_DRCI_CKEN
-#endif /* MB86R0X_H */
#include <common.h>
#include <linux/kbuild.h>
-#if defined(CONFIG_MB86R0x)
-#include <asm/arch/mb86r0x.h>
-#endif
#if defined(CONFIG_MX25) || defined(CONFIG_MX27) || defined(CONFIG_MX35) \
|| defined(CONFIG_MX51) || defined(CONFIG_MX53)
#include <asm/arch/imx-regs.h>
{
/*
* TODO : Check if each entry in this file is really necessary.
- * - struct mb86r0x_ddr2
- * - struct mb86r0x_memc
* - struct esdramc_regs
* - struct max_regs
* - struct aips_regs
* code. Is it better to define the macros directly in headers?
*/
-#if defined(CONFIG_MB86R0x)
- /* ddr2 controller */
- DEFINE(DDR2_DRIC, offsetof(struct mb86r0x_ddr2c, dric));
- DEFINE(DDR2_DRIC1, offsetof(struct mb86r0x_ddr2c, dric1));
- DEFINE(DDR2_DRIC2, offsetof(struct mb86r0x_ddr2c, dric2));
- DEFINE(DDR2_DRCA, offsetof(struct mb86r0x_ddr2c, drca));
- DEFINE(DDR2_DRCM, offsetof(struct mb86r0x_ddr2c, drcm));
- DEFINE(DDR2_DRCST1, offsetof(struct mb86r0x_ddr2c, drcst1));
- DEFINE(DDR2_DRCST2, offsetof(struct mb86r0x_ddr2c, drcst2));
- DEFINE(DDR2_DRCR, offsetof(struct mb86r0x_ddr2c, drcr));
- DEFINE(DDR2_DRCF, offsetof(struct mb86r0x_ddr2c, drcf));
- DEFINE(DDR2_DRASR, offsetof(struct mb86r0x_ddr2c, drasr));
- DEFINE(DDR2_DRIMS, offsetof(struct mb86r0x_ddr2c, drims));
- DEFINE(DDR2_DROS, offsetof(struct mb86r0x_ddr2c, dros));
- DEFINE(DDR2_DRIBSODT1, offsetof(struct mb86r0x_ddr2c, dribsodt1));
- DEFINE(DDR2_DROABA, offsetof(struct mb86r0x_ddr2c, droaba));
- DEFINE(DDR2_DROBS, offsetof(struct mb86r0x_ddr2c, drobs));
-
- /* clock reset generator */
- DEFINE(CRG_CRPR, offsetof(struct mb86r0x_crg, crpr));
- DEFINE(CRG_CRHA, offsetof(struct mb86r0x_crg, crha));
- DEFINE(CRG_CRPA, offsetof(struct mb86r0x_crg, crpa));
- DEFINE(CRG_CRPB, offsetof(struct mb86r0x_crg, crpb));
- DEFINE(CRG_CRHB, offsetof(struct mb86r0x_crg, crhb));
- DEFINE(CRG_CRAM, offsetof(struct mb86r0x_crg, cram));
-
- /* chip control module */
- DEFINE(CCNT_CDCRC, offsetof(struct mb86r0x_ccnt, cdcrc));
-
- /* external bus interface */
- DEFINE(MEMC_MCFMODE0, offsetof(struct mb86r0x_memc, mcfmode[0]));
- DEFINE(MEMC_MCFMODE2, offsetof(struct mb86r0x_memc, mcfmode[2]));
- DEFINE(MEMC_MCFMODE4, offsetof(struct mb86r0x_memc, mcfmode[4]));
- DEFINE(MEMC_MCFTIM0, offsetof(struct mb86r0x_memc, mcftim[0]));
- DEFINE(MEMC_MCFTIM2, offsetof(struct mb86r0x_memc, mcftim[2]));
- DEFINE(MEMC_MCFTIM4, offsetof(struct mb86r0x_memc, mcftim[4]));
- DEFINE(MEMC_MCFAREA0, offsetof(struct mb86r0x_memc, mcfarea[0]));
- DEFINE(MEMC_MCFAREA2, offsetof(struct mb86r0x_memc, mcfarea[2]));
- DEFINE(MEMC_MCFAREA4, offsetof(struct mb86r0x_memc, mcfarea[4]));
-#endif
-
#if defined(CONFIG_MX25)
/* Clock Control Module */
DEFINE(CCM_CCTL, offsetof(struct ccm_regs, cctl));
+++ /dev/null
-if TARGET_JADECPU
-
-config SYS_BOARD
- default "jadecpu"
-
-config SYS_VENDOR
- default "syteco"
-
-config SYS_SOC
- default "mb86r0x"
-
-config SYS_CONFIG_NAME
- default "jadecpu"
-
-endif
+++ /dev/null
-JADECPU BOARD
-M: Matthias Weisser <weisserm@arcor.de>
-S: Maintained
-F: board/syteco/jadecpu/
-F: include/configs/jadecpu.h
-F: configs/jadecpu_defconfig
+++ /dev/null
-#
-# (C) Copyright 2003-2008
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# (C) Copyright 2008
-# Stelian Pop <stelian@popies.net>
-# Lead Tech Design <www.leadtechdesign.com>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y += jadecpu.o
-obj-y += lowlevel_init.o
+++ /dev/null
-/*
- * (c) 2010 Graf-Syteco, Matthias Weisser
- * <weisserm@arcor.de>
- *
- * (C) Copyright 2007, mycable GmbH
- * Carsten Schneider <cs@mycable.de>, Alexander Bigga <ab@mycable.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#include <asm/io.h>
-#include <asm/arch/mb86r0x.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-int board_init(void)
-{
- struct mb86r0x_ccnt * ccnt = (struct mb86r0x_ccnt *)
- MB86R0x_CCNT_BASE;
-
- /* We select mode 0 for group 2 and mode 1 for group 4 */
- writel(0x00000010, &ccnt->cmux_md);
-
- gd->flags = 0;
- gd->bd->bi_boot_params = PHYS_SDRAM + PHYS_SDRAM_SIZE - 0x10000;
-
- icache_enable();
- dcache_enable();
-
- return 0;
-}
-
-static void setup_display_power(uint32_t pwr_bit, char *pwm_opts,
- unsigned long pwm_base)
-{
- struct mb86r0x_gpio *gpio = (struct mb86r0x_gpio *)
- MB86R0x_GPIO_BASE;
- struct mb86r0x_pwm *pwm = (struct mb86r0x_pwm *) pwm_base;
- const char *e;
-
- writel(readl(&gpio->gpdr2) | pwr_bit, &gpio->gpdr2);
-
- e = getenv(pwm_opts);
- if (e != NULL) {
- const char *s;
- uint32_t freq, init;
-
- freq = 0;
- init = 0;
-
- s = strchr(e, 'f');
- if (s != NULL)
- freq = simple_strtol(s + 2, NULL, 0);
-
- s = strchr(e, 'i');
- if (s != NULL)
- init = simple_strtol(s + 2, NULL, 0);
-
- if (freq > 0) {
- writel(CONFIG_MB86R0x_IOCLK / 1000 / freq,
- &pwm->bcr);
- writel(1002, &pwm->tpr);
- writel(1, &pwm->pr);
- writel(init * 10 + 1, &pwm->dr);
- writel(1, &pwm->cr);
- writel(1, &pwm->sr);
- }
- }
-}
-
-int board_late_init(void)
-{
- struct mb86r0x_gpio *gpio = (struct mb86r0x_gpio *)
- MB86R0x_GPIO_BASE;
- uint32_t in_word;
-
-#ifdef CONFIG_VIDEO_MB86R0xGDC
- /* Check if we have valid display settings and turn on power if so */
- /* Display 0 */
- if (getenv("gs_dsp_0_param") || getenv("videomode"))
- setup_display_power((1 << 3), "gs_dsp_0_pwm",
- MB86R0x_PWM0_BASE);
-
- /* The corresponding GPIO is always an output */
- writel(readl(&gpio->gpddr2) | (1 << 3), &gpio->gpddr2);
-
- /* Display 1 */
- if (getenv("gs_dsp_1_param") || getenv("videomode1"))
- setup_display_power((1 << 4), "gs_dsp_1_pwm",
- MB86R0x_PWM1_BASE);
-
- /* The corresponding GPIO is always an output */
- writel(readl(&gpio->gpddr2) | (1 << 4), &gpio->gpddr2);
-#endif /* CONFIG_VIDEO_MB86R0xGDC */
-
- /* 5V enable */
- writel(readl(&gpio->gpdr1) & ~(1 << 5), &gpio->gpdr1);
- writel(readl(&gpio->gpddr1) | (1 << 5), &gpio->gpddr1);
-
- /* We have special boot options if told by GPIOs */
- in_word = readl(&gpio->gpdr1);
-
- if ((in_word & 0xC0) == 0xC0) {
- setenv("stdin", "serial");
- setenv("stdout", "serial");
- setenv("stderr", "serial");
- setenv("preboot", "run gs_slow_boot");
- } else if ((in_word & 0xC0) != 0) {
- setenv("stdout", "vga");
- setenv("preboot", "run gs_slow_boot");
- } else {
- setenv("stdin", "serial");
- setenv("stdout", "serial");
- setenv("stderr", "serial");
- if (getenv("gs_devel")) {
- setenv("preboot", "run gs_slow_boot");
- } else {
- setenv("preboot", "run gs_fast_boot");
- }
- }
-
- return 0;
-}
-
-int misc_init_r(void)
-{
- return 0;
-}
-
-/*
- * DRAM configuration
- */
-int dram_init(void)
-{
- /* dram_init must store complete ramsize in gd->ram_size */
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
- PHYS_SDRAM_SIZE);
-
- return 0;
-}
-
-void dram_init_banksize(void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM;
- gd->bd->bi_dram[0].size = gd->ram_size;
-}
-
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_SMC911X
- rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
-#endif
- return rc;
-}
+++ /dev/null
-/*
- * Board specific setup info
- *
- * (C) Copyright 2007, mycable GmbH
- * Carsten Schneider <cs@mycable.de>, Alexander Bigga <ab@mycable.de>
- *
- * (C) Copyright 2003, ARM Ltd.
- * Philippe Robin, <philippe.robin@arm.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/macro.h>
-#include <asm/arch/mb86r0x.h>
-#include <generated/asm-offsets.h>
-
-/* Set up the platform, once the cpu has been initialized */
-.globl lowlevel_init
-lowlevel_init:
-/*
- * Initialize Clock Reset Generator (CRG)
- */
-
- ldr r0, =MB86R0x_CRG_BASE
-
- /* Not change the initial value that is set by external pin.*/
-WAIT_PLL:
- ldr r2, [r0, #CRG_CRPR] /* Wait for PLLREADY */
- tst r2, #MB86R0x_CRG_CRPR_PLLRDY
- beq WAIT_PLL
-
- /* Set clock gate control */
- ldr r1, =CONFIG_SYS_CRG_CRHA_INIT
- str r1, [r0, #CRG_CRHA]
- ldr r1, =CONFIG_SYS_CRG_CRPA_INIT
- str r1, [r0, #CRG_CRPA]
- ldr r1, =CONFIG_SYS_CRG_CRPB_INIT
- str r1, [r0, #CRG_CRPB]
- ldr r1, =CONFIG_SYS_CRG_CRHB_INIT
- str r1, [r0, #CRG_CRHB]
- ldr r1, =CONFIG_SYS_CRG_CRAM_INIT
- str r1, [r0, #CRG_CRAM]
-
-/*
- * Initialize External Bus Interface
- */
- ldr r0, =MB86R0x_MEMC_BASE
-
- ldr r1, =CONFIG_SYS_MEMC_MCFMODE0_INIT
- str r1, [r0, #MEMC_MCFMODE0]
- ldr r1, =CONFIG_SYS_MEMC_MCFMODE2_INIT
- str r1, [r0, #MEMC_MCFMODE2]
- ldr r1, =CONFIG_SYS_MEMC_MCFMODE4_INIT
- str r1, [r0, #MEMC_MCFMODE4]
-
- ldr r1, =CONFIG_SYS_MEMC_MCFTIM0_INIT
- str r1, [r0, #MEMC_MCFTIM0]
- ldr r1, =CONFIG_SYS_MEMC_MCFTIM2_INIT
- str r1, [r0, #MEMC_MCFTIM2]
- ldr r1, =CONFIG_SYS_MEMC_MCFTIM4_INIT
- str r1, [r0, #MEMC_MCFTIM4]
-
- ldr r1, =CONFIG_SYS_MEMC_MCFAREA0_INIT
- str r1, [r0, #MEMC_MCFAREA0]
- ldr r1, =CONFIG_SYS_MEMC_MCFAREA2_INIT
- str r1, [r0, #MEMC_MCFAREA2]
- ldr r1, =CONFIG_SYS_MEMC_MCFAREA4_INIT
- str r1, [r0, #MEMC_MCFAREA4]
-
-/*
- * Initialize DDR2 Controller
- */
-
- /* Wait for PLL LOCK up time or more */
- wait_timer 20
-
- /*
- * (2) Initialize DDRIF
- */
- ldr r0, =MB86R0x_DDR2_BASE
- ldr r1, =CONFIG_SYS_DDR2_DRIMS_INIT
- strh r1, [r0, #DDR2_DRIMS]
-
- /*
- * (3) Wait for 20MCKPs(120nsec) or more
- */
- wait_timer 20
-
- /*
- * (4) IRESET/IUSRRST release
- */
- ldr r0, =MB86R0x_CCNT_BASE
- ldr r1, =CONFIG_SYS_CCNT_CDCRC_INIT_1
- str r1, [r0, #CCNT_CDCRC]
-
- /*
- * (5) Wait for 20MCKPs(120nsec) or more
- */
- wait_timer 20
-
- /*
- * (6) IDLLRST release
- */
- ldr r0, =MB86R0x_CCNT_BASE
- ldr r1, =CONFIG_SYS_CCNT_CDCRC_INIT_2
- str r1, [r0, #CCNT_CDCRC]
-
- /*
- * (7+8) Wait for 200us(=200000ns) or more (DDR2 Spec)
- */
- wait_timer 33536
-
- /*
- * (9) MCKE ON
- */
- ldr r0, =MB86R0x_DDR2_BASE
- ldr r1, =CONFIG_SYS_DDR2_DRIC1_INIT
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_DRIC2_INIT
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =CONFIG_SYS_DDR2_DRCA_INIT
- strh r1, [r0, #DDR2_DRCA]
- ldr r1, =MB86R0x_DDR2_DRCI_INIT
- strh r1, [r0, #DDR2_DRIC]
-
- /*
- * (10) Initialize SDRAM
- */
-
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- wait_timer 67 /* 400ns wait */
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_1
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_1
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_2
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_2
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_3
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_3
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_4
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_4
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_5
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_5
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- wait_timer 200
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_6
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_6
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_7
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_7
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- wait_timer 18 /* 105ns wait */
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_8
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_8
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- wait_timer 200 /* MRS to OCD: 200clock */
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_9
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_9
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_10
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_10
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- ldr r1, =CONFIG_SYS_DDR2_DRCM_INIT
- strh r1, [r0, #DDR2_DRCM]
-
- ldr r1, =CONFIG_SYS_DDR2_DRCST1_INIT
- strh r1, [r0, #DDR2_DRCST1]
-
- ldr r1, =CONFIG_SYS_DDR2_DRCST2_INIT
- strh r1, [r0, #DDR2_DRCST2]
-
- ldr r1, =CONFIG_SYS_DDR2_DRCR_INIT
- strh r1, [r0, #DDR2_DRCR]
-
- ldr r1, =CONFIG_SYS_DDR2_DRCF_INIT
- strh r1, [r0, #DDR2_DRCF]
-
- ldr r1, =CONFIG_SYS_DDR2_DRASR_INIT
- strh r1, [r0, #DDR2_DRASR]
-
- /*
- * (11) ODT setting
- */
- ldr r1, =CONFIG_SYS_DDR2_DROBS_INIT
- strh r1, [r0, #DDR2_DROBS]
- ldr r1, =CONFIG_SYS_DDR2_DROABA_INIT
- strh r1, [r0, #DDR2_DROABA]
- ldr r1, =CONFIG_SYS_DDR2_DRIBSODT1_INIT
- strh r1, [r0, #DDR2_DRIBSODT1]
-
- /*
- * (12) Shift to ODTCONT ON (SDRAM side) and DDR2 usual operation mode
- */
- ldr r1, =CONFIG_SYS_DDR2_DROS_INIT
- strh r1, [r0, #DDR2_DROS]
- ldr r1, =MB86R0x_DDR2_DRCI_NORMAL
- strh r1, [r0, #DDR2_DRIC]
-
- mov pc, lr
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_TARGET_JADECPU=y
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
-icecube_5200 powerpc mpc5xxx - - Wolfgang Denk <wd@denx.de>
-Lite5200 powerpc mpc5xxx - -
-cpci5200 powerpc mpc5xxx - - Reinhard Arlt <reinhard.arlt@esd-electronics.com>
-mecp5200 powerpc mpc5xxx - - Reinhard Arlt <reinhard.arlt@esd-electronics.com>
-pf5200 powerpc mpc5xxx - - Reinhard Arlt <reinhard.arlt@esd-electronics.com>
-PM520 powerpc mpc5xxx - - Josef Wagner <Wagner@Microsys.de>
-Total5200 powerpc mpc5xxx - -
-CATcenter powerpc ppc4xx - -
-PPChameleonEVB powerpc ppc4xx - - Andrea "llandre" Marson <andrea.marson@dave-tech.it>
-P2020DS powerpc mpc85xx - -
-P2020COME powerpc mpc85xx - - Ira W. Snyder <iws@ovro.caltech.edu>
-P2020RDB powerpc mpc85xx - - Poonam Aggrwal <poonam.aggrwal@freescale.com>
-P2010RDB powerpc mpc85xx - -
-P1020RDB powerpc mpc85xx - -
-P1011RDB powerpc mpc85xx - -
-MPC8360EMDS powerpc mpc83xx - - Dave Liu <daveliu@freescale.com>
-MPC8360ERDK powerpc mpc83xx - - Anton Vorontsov <avorontsov@ru.mvista.com>
+jadecpu arm arm926ejs - - Matthias Weisser <weisserm@arcor.de>
+icecube_5200 powerpc mpc5xxx 37b608a5 2015-01-23 Wolfgang Denk <wd@denx.de>
+Lite5200 powerpc mpc5xxx 37b608a5 2015-01-23
+cpci5200 powerpc mpc5xxx 37b608a5 2015-01-23 Reinhard Arlt <reinhard.arlt@esd-electronics.com>
+mecp5200 powerpc mpc5xxx 37b608a5 2015-01-23 Reinhard Arlt <reinhard.arlt@esd-electronics.com>
+pf5200 powerpc mpc5xxx 37b608a5 2015-01-23 Reinhard Arlt <reinhard.arlt@esd-electronics.com>
+PM520 powerpc mpc5xxx a258e732 2015-01-23 Josef Wagner <Wagner@Microsys.de>
+Total5200 powerpc mpc5xxx ad734f7d 2015-01-23
+CATcenter powerpc ppc4xx 5344cc1a 2015-01-23
+PPChameleonEVB powerpc ppc4xx 5344cc1a 2015-01-23 Andrea "llandre" Marson <andrea.marson@dave-tech.it>
+P2020DS powerpc mpc85xx 168dcc6c 2015-01-23
+P2020COME powerpc mpc85xx 89123536 2015-01-23 Ira W. Snyder <iws@ovro.caltech.edu>
+P2020RDB powerpc mpc85xx 743d4815 2015-01-23 Poonam Aggrwal <poonam.aggrwal@freescale.com>
+P2010RDB powerpc mpc85xx 743d4815 2015-01-23
+P1020RDB powerpc mpc85xx 743d4815 2015-01-23
+P1011RDB powerpc mpc85xx 743d4815 2015-01-23
+MPC8360EMDS powerpc mpc83xx 8d1e3cb1 2015-01-23 Dave Liu <daveliu@freescale.com>
+MPC8360ERDK powerpc mpc83xx 8d1e3cb1 2015-01-23 Anton Vorontsov <avorontsov@ru.mvista.com>
P3G4 powerpc 74xx_7xx d928664f 2015-01-16 Wolfgang Denk <wd@denx.de>
ZUMA powerpc 74xx_7xx d928664f 2015-01-16 Nye Liu <nyet@zumanetworks.com>
ppmc7xx powerpc 74xx_7xx d928664f 2015-01-16
obj-$(CONFIG_VIDEO_LCD_HITACHI_TX18D42VM) += hitachi_tx18d42vm_lcd.o
obj-$(CONFIG_VIDEO_LCD_SSD2828) += ssd2828.o
obj-$(CONFIG_VIDEO_MB862xx) += mb862xx.o videomodes.o
-obj-$(CONFIG_VIDEO_MB86R0xGDC) += mb86r0xgdc.o videomodes.o
obj-$(CONFIG_VIDEO_MX3) += mx3fb.o videomodes.o
obj-$(CONFIG_VIDEO_IPUV3) += mxc_ipuv3_fb.o ipu_common.o ipu_disp.o
obj-$(CONFIG_VIDEO_MXS) += mxsfb.o videomodes.o
+++ /dev/null
-/*
- * (C) Copyright 2010
- * Matthias Weisser <weisserm@arcor.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * mb86r0xgdc.c - Graphic interface for Fujitsu MB86R0x integrated graphic
- * controller.
- */
-
-#include <common.h>
-
-#include <malloc.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-#include <video_fb.h>
-#include "videomodes.h"
-
-/*
- * 4MB (at the end of system RAM)
- */
-#define VIDEO_MEM_SIZE 0x400000
-
-#define FB_SYNC_CLK_INV (1<<16) /* pixel clock inverted */
-
-/*
- * Graphic Device
- */
-static GraphicDevice mb86r0x;
-
-static void dsp_init(struct mb86r0x_gdc_dsp *dsp, char *modestr,
- u32 *videomem)
-{
- struct ctfb_res_modes var_mode;
- u32 dcm1, dcm2, dcm3;
- u16 htp, hdp, hdb, hsp, vtr, vsp, vdp;
- u8 hsw, vsw;
- u32 l2m, l2em, l2oa0, l2da0, l2oa1, l2da1;
- u16 l2dx, l2dy, l2wx, l2wy, l2ww, l2wh;
- unsigned long div;
- int bpp;
-
- bpp = video_get_params(&var_mode, modestr);
-
- if (bpp == 0) {
- var_mode.xres = 640;
- var_mode.yres = 480;
- var_mode.pixclock = 39721; /* 25MHz */
- var_mode.left_margin = 48;
- var_mode.right_margin = 16;
- var_mode.upper_margin = 33;
- var_mode.lower_margin = 10;
- var_mode.hsync_len = 96;
- var_mode.vsync_len = 2;
- var_mode.sync = 0;
- var_mode.vmode = 0;
- bpp = 15;
- }
-
- /* Fill memory with white */
- memset(videomem, 0xFF, var_mode.xres * var_mode.yres * 2);
-
- mb86r0x.winSizeX = var_mode.xres;
- mb86r0x.winSizeY = var_mode.yres;
-
- /* LCD base clock is ~ 660MHZ. We do calculations in kHz */
- div = 660000 / (1000000000L / var_mode.pixclock);
- if (div > 64)
- div = 64;
- if (0 == div)
- div = 1;
-
- dcm1 = (div - 1) << 8;
- dcm2 = 0x00000000;
- if (var_mode.sync & FB_SYNC_CLK_INV)
- dcm3 = 0x00000100;
- else
- dcm3 = 0x00000000;
-
- htp = var_mode.left_margin + var_mode.xres +
- var_mode.hsync_len + var_mode.right_margin;
- hdp = var_mode.xres;
- hdb = var_mode.xres;
- hsp = var_mode.xres + var_mode.right_margin;
- hsw = var_mode.hsync_len;
-
- vsw = var_mode.vsync_len;
- vtr = var_mode.upper_margin + var_mode.yres +
- var_mode.vsync_len + var_mode.lower_margin;
- vsp = var_mode.yres + var_mode.lower_margin;
- vdp = var_mode.yres;
-
- l2m = ((var_mode.yres - 1) << (0)) |
- (((var_mode.xres * 2) / 64) << (16)) |
- ((1) << (31));
-
- l2em = (1 << 0) | (1 << 1);
-
- l2oa0 = mb86r0x.frameAdrs;
- l2da0 = mb86r0x.frameAdrs;
- l2oa1 = mb86r0x.frameAdrs;
- l2da1 = mb86r0x.frameAdrs;
- l2dx = 0;
- l2dy = 0;
- l2wx = 0;
- l2wy = 0;
- l2ww = var_mode.xres;
- l2wh = var_mode.yres - 1;
-
- writel(dcm1, &dsp->dcm1);
- writel(dcm2, &dsp->dcm2);
- writel(dcm3, &dsp->dcm3);
-
- writew(htp, &dsp->htp);
- writew(hdp, &dsp->hdp);
- writew(hdb, &dsp->hdb);
- writew(hsp, &dsp->hsp);
- writeb(hsw, &dsp->hsw);
-
- writeb(vsw, &dsp->vsw);
- writew(vtr, &dsp->vtr);
- writew(vsp, &dsp->vsp);
- writew(vdp, &dsp->vdp);
-
- writel(l2m, &dsp->l2m);
- writel(l2em, &dsp->l2em);
- writel(l2oa0, &dsp->l2oa0);
- writel(l2da0, &dsp->l2da0);
- writel(l2oa1, &dsp->l2oa1);
- writel(l2da1, &dsp->l2da1);
- writew(l2dx, &dsp->l2dx);
- writew(l2dy, &dsp->l2dy);
- writew(l2wx, &dsp->l2wx);
- writew(l2wy, &dsp->l2wy);
- writew(l2ww, &dsp->l2ww);
- writew(l2wh, &dsp->l2wh);
-
- writel(dcm1 | (1 << 18) | (1 << 31), &dsp->dcm1);
-}
-
-void *video_hw_init(void)
-{
- struct mb86r0x_gdc *gdc = (struct mb86r0x_gdc *) MB86R0x_GDC_BASE;
- GraphicDevice *pGD = &mb86r0x;
- char *s;
- u32 *vid;
-
- memset(pGD, 0, sizeof(GraphicDevice));
-
- pGD->gdfIndex = GDF_15BIT_555RGB;
- pGD->gdfBytesPP = 2;
- pGD->memSize = VIDEO_MEM_SIZE;
- pGD->frameAdrs = PHYS_SDRAM + PHYS_SDRAM_SIZE - VIDEO_MEM_SIZE;
-
- vid = (u32 *)pGD->frameAdrs;
-
- s = getenv("videomode");
- if (s != NULL)
- dsp_init(&gdc->dsp0, s, vid);
-
- s = getenv("videomode1");
- if (s != NULL)
- dsp_init(&gdc->dsp1, s, vid);
-
- return pGD;
-}
+++ /dev/null
-/*
- * (C) Copyright 2010
- * Matthias Weisser <weisserm@arcor.de>
- *
- * Configuation settings for the jadecpu board
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_MB86R0x
-#define CONFIG_MB86R0x_IOCLK get_bus_freq(0)
-#define CONFIG_SYS_TEXT_BASE 0x10000000
-
-
-#define CONFIG_USE_ARCH_MEMCPY
-#define CONFIG_USE_ARCH_MEMSET
-
-#define MACH_TYPE_JADECPU 2636
-
-#define CONFIG_MACH_TYPE MACH_TYPE_JADECPU
-
-/*
- * Environment settings
- */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "gs_fast_boot=setenv bootdelay 5\0" \
- "gs_slow_boot=setenv bootdelay 10\0" \
- "bootcmd=dcache off; mw.l 0x40000000 0 1024; usb start;" \
- "fatls usb 0; fatload usb 0 0x40000000 jadecpu-init.bin;" \
- "bootelf 0x40000000\0" \
- ""
-
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-#define CONFIG_BOARD_LATE_INIT
-
-/*
- * Compressions
- */
-#define CONFIG_LZO
-
-/*
- * Hardware drivers
- */
-
-/*
- * Serial
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CONFIG_SYS_NS16550_COM1 0xfffe1000 /* UART 0 */
-#define CONFIG_SYS_NS16550_COM2 0xfff50000 /* UART 2 */
-#define CONFIG_SYS_NS16550_COM3 0xfff51000 /* UART 3 */
-#define CONFIG_SYS_NS16550_COM4 0xfff43000 /* UART 4 */
-
-#define CONFIG_CONS_INDEX 4
-
-/*
- * Ethernet
- */
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_BASE 0x02000000
-#define CONFIG_SMC911X_16_BIT
-
-/*
- * Video
- */
-#define CONFIG_VIDEO
-#define CONFIG_VIDEO_MB86R0xGDC
-#define CONFIG_SYS_WHITE_ON_BLACK
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_SPLASH_SCREEN_ALIGN
-#define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_VIDEO_BMP_GZIP
-#define CONFIG_VIDEO_BMP_RLE8
-#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (800*480 + 256*4 + 10*1024)
-#define VIDEO_FB_16BPP_WORD_SWAP
-#define VIDEO_KBD_INIT_FCT 0
-#define VIDEO_TSTC_FCT serial_stub_tstc
-#define VIDEO_GETC_FCT serial_stub_getc
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE 1
-#define CONFIG_BOOTP_BOOTPATH 1
-#define CONFIG_BOOTP_GATEWAY 1
-#define CONFIG_BOOTP_HOSTNAME 1
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_SOURCE
-#undef CONFIG_CMD_NFS
-#undef CONFIG_CMD_XIMG
-
-#define CONFIG_CMD_BMP
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_CACHE
-
-#define CONFIG_SYS_HUSH_PARSER
-
-/* USB */
-#define CONFIG_USB_OHCI_NEW
-#define CONFIG_SYS_USB_OHCI_REGS_BASE 0xFFF81000
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME "mb86r0x"
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 1
-#define CONFIG_USB_STORAGE
-#define CONFIG_DOS_PARTITION
-
-/* SDRAM */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM 0x40000000 /* Start address of DDRRAM */
-#define PHYS_SDRAM_SIZE 0x08000000 /* 128 megs */
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
-#define CONFIG_SYS_INIT_SP_ADDR 0x01008000
-
-/*
- * FLASH and environment organization
- */
-#define CONFIG_SYS_FLASH_BASE 0x10000000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_MAX_FLASH_SECT 256
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000)
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SECT_SIZE (128 * 1024)
-#define CONFIG_ENV_SIZE (128 * 1024)
-
-/*
- * CFI FLASH driver setup
- */
-#define CONFIG_SYS_FLASH_CFI 1
-#define CONFIG_FLASH_CFI_DRIVER 1
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* ~10x faster */
-
-#define CONFIG_SYS_LOAD_ADDR 0x40000000 /* load address */
-
-#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM + (512*1024))
-#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM + PHYS_SDRAM_SIZE)
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_SYS_PROMPT "jade> "
-#define CONFIG_SYS_CBSIZE 256
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP 1
-#define CONFIG_CMDLINE_EDITING 1
-
-#define CONFIG_PREBOOT ""
-
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT "boot in %d s\n", bootdelay
-#define CONFIG_AUTOBOOT_DELAY_STR "delaygs"
-#define CONFIG_AUTOBOOT_STOP_STR "stopgs"
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (10 << 20)
-#define CONFIG_SYS_MEM_TOP_HIDE (4 << 20)
-
-/*
- * Clock reset generator init
- */
-#define CONFIG_SYS_CRG_CRHA_INIT 0xffff
-#define CONFIG_SYS_CRG_CRPA_INIT 0xffff
-#define CONFIG_SYS_CRG_CRPB_INIT 0xfffe
-#define CONFIG_SYS_CRG_CRHB_INIT 0xffff
-#define CONFIG_SYS_CRG_CRAM_INIT 0xffef
-
-/*
- * Memory controller settings
- */
-#define CONFIG_SYS_MEMC_MCFMODE0_INIT 0x00000001 /* 16bit */
-#define CONFIG_SYS_MEMC_MCFMODE2_INIT 0x00000001 /* 16bit */
-#define CONFIG_SYS_MEMC_MCFMODE4_INIT 0x00000021 /* 16bit, Page*/
-#define CONFIG_SYS_MEMC_MCFTIM0_INIT 0x16191008
-#define CONFIG_SYS_MEMC_MCFTIM2_INIT 0x03061008
-#define CONFIG_SYS_MEMC_MCFTIM4_INIT 0x03061804
-#define CONFIG_SYS_MEMC_MCFAREA0_INIT 0x000000c0 /* 0x0c000000 1MB */
-#define CONFIG_SYS_MEMC_MCFAREA2_INIT 0x00000020 /* 0x02000000 1MB */
-#define CONFIG_SYS_MEMC_MCFAREA4_INIT 0x001f0000 /* 0x10000000 32 MB */
-
-/*
- * DDR2 controller init settings
- */
-#define CONFIG_SYS_DDR2_DRIMS_INIT 0x5555
-#define CONFIG_SYS_CCNT_CDCRC_INIT_1 0x00000002
-#define CONFIG_SYS_CCNT_CDCRC_INIT_2 0x00000003
-#define CONFIG_SYS_DDR2_DRIC1_INIT 0x003f
-#define CONFIG_SYS_DDR2_DRIC2_INIT 0x0000
-#define CONFIG_SYS_DDR2_DRCA_INIT 0xc124 /* 512Mbit DDR2SDRAM x 2 */
-#define CONFIG_SYS_DDR2_DRCM_INIT 0x0032
-#define CONFIG_SYS_DDR2_DRCST1_INIT 0x3418
-#define CONFIG_SYS_DDR2_DRCST2_INIT 0x6e32
-#define CONFIG_SYS_DDR2_DRCR_INIT 0x0141
-#define CONFIG_SYS_DDR2_DRCF_INIT 0x0002
-#define CONFIG_SYS_DDR2_DRASR_INIT 0x0001
-#define CONFIG_SYS_DDR2_DROBS_INIT 0x0001
-#define CONFIG_SYS_DDR2_DROABA_INIT 0x0103
-#define CONFIG_SYS_DDR2_DRIBSODT1_INIT 0x003F
-#define CONFIG_SYS_DDR2_DROS_INIT 0x0001
-
-/*
- * DRAM init sequence
- */
-
-/* PALL Command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_1 0x0017
-#define CONFIG_SYS_DDR2_INIT_DRIC2_1 0x0400
-
-/* EMR(2) command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_2 0x0006
-#define CONFIG_SYS_DDR2_INIT_DRIC2_2 0x0000
-
-/* EMR(3) command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_3 0x0007
-#define CONFIG_SYS_DDR2_INIT_DRIC2_3 0x0000
-
-/* EMR(1) command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_4 0x0005
-#define CONFIG_SYS_DDR2_INIT_DRIC2_4 0x0000
-
-/* MRS command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_5 0x0004
-#define CONFIG_SYS_DDR2_INIT_DRIC2_5 0x0532
-
-/* PALL command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_6 0x0017
-#define CONFIG_SYS_DDR2_INIT_DRIC2_6 0x0400
-
-/* REF command 1 */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_7 0x000f
-#define CONFIG_SYS_DDR2_INIT_DRIC2_7 0x0000
-
-/* MRS command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_8 0x0004
-#define CONFIG_SYS_DDR2_INIT_DRIC2_8 0x0432
-
-/* EMR(1) command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_9 0x0005
-#define CONFIG_SYS_DDR2_INIT_DRIC2_9 0x0380
-
-/* EMR(1) command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_10 0x0005
-#define CONFIG_SYS_DDR2_INIT_DRIC2_10 0x0002
-
-#endif /* __CONFIG_H */
#if defined(CONFIG_405GP) || \
defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \
defined(CONFIG_405EX) || defined(CONFIG_440) || \
- defined(CONFIG_MB86R0x) || defined(CONFIG_MPC5xxx) || \
+ defined(CONFIG_MPC5xxx) || \
defined(CONFIG_MPC83xx) || defined(CONFIG_MPC85xx) || \
defined(CONFIG_MPC86xx) || defined(CONFIG_SYS_SC520) || \
defined(CONFIG_TEGRA) || defined(CONFIG_SYS_COREBOOT) || \
projects / u-boot / commitdiff